As we now store enough information in the device_node.
Also the Flags field was not used either, do remove that.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
As we now store enough information in the device_node to allocate the
irq number in pcibios_final_fixup.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
We can now scan the list of device nodes instead. This also allows us
to remove the Device_list member of struct pci_dn.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Add a function for generic parsing of dma-window properties (ie,
ibm,dma-window and ibm,my-dma-window) of pci and virtual device nodes.
This function will also be used by cell.
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch allows the compiler to catch any printf-like mismatches for
udbg_printf(). After some brute force building I've only found issues
with my own code and lparcfg.c It could break some developers, but
IMHO that would be goodness.
Signed-off-by: Jimi Xenidis <jimix@watson.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
We need to know the base address of the kdump kernel even when we're not a
kdump kernel, so add a #define for it. Move the logic that sets the kdump
kernelbase into kdump.h instead of page.h.
Rename kdump_setup() to setup_kdump_trampoline() to make it clearer what it's
doing, and add an empty definition for the !CRASH_DUMP case to avoid a
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
We currently do mem= handling in three seperate places. And as benh pointed out
I wrote two of them. Now that we parse command line parameters earlier we can
clean this mess up.
Moving the parsing out of prom_init means the device tree might be allocated
above the memory limit. If that happens we'd have to move it. As it happens
we already have logic to do that for kdump, so just genericise it.
This also means we might have reserved regions above the memory limit, if we
do the bootmem allocator will blow up, so we have to modify
lmb_enforce_memory_limit() to truncate the reserves as well.
Tested on P5 LPAR, iSeries, F50, 44p. Tested moving device tree on P5 and
44p and F50.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
In reg.h we mostly have #define<space> but there are a few #define<tab>
around. Clean these up so we use space exclusively.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
We have a case where __get_user and __put_user can validly be used
on kernel addresses in interrupt context - namely, the alignment
exception handler, as our get/put_unaligned just do a single access
and rely on the alignment exception handler to fix things up in the
rare cases where the cpu can't handle it in hardware. Thus we can
get alignment exceptions in the network stack at interrupt level.
The alignment exception handler does a __get_user to read the
instruction and blows up in might_sleep().
Since a __get_user on a kernel address won't actually ever sleep,
this makes the might_sleep conditional on the address being less
than PAGE_OFFSET.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Add an nid member to the spu structure, and store the numa id of the spu there
on creation.
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Change of_node_to_nid() to traverse the device tree, looking for a numa id.
Cell uses this to assign ids to SPUs, which are children of the CPU node.
Existing users of of_node_to_nid() are altered to use of_node_to_nid_single(),
which doesn't do the traversal.
Export an attach_sysdev_to_node() function, allowing system devices (eg.
SPUs) to link themselves into the numa topology in sysfs.
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
It's been long overdue to kill the union tce_entry in the pSeries/iSeries
TCE code, especially since I asked the Summit guys to do it on the code
they copied from us.
Also, while I was at it, I cleaned up some whitespace.
Built and booted on pSeries, built on iSeries.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This requires the compatible properties having vaules that are empty
strings instead of just being empty properties.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
As an added bonus, since every vio_dev now has a device_node
associated with it, hotplug now works.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Add a cputable entry for the POWER6 processor.
The SIHV and SIPR bits in the mmcra have moved in POWER6, so disable
support for that until oprofile is fixed.
Also tell firmware that we know about POWER6.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
These aren't needed by glibc or klibc, and they're broken in some cases
anyway. The uClibc folks are apparently switching over to stop using
them too (now that we agreed that they should be dropped, at least).
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Wire up *at syscalls.
This patch has been tested on ppc64 (using glibc's testsuite, both 32bit
and 64bit), and compile-tested for ppc32 (I have currently no ppc32 system
available, but I expect no problems).
Signed-off-by: Andreas Schwab <schwab@suse.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Some people report that we die on some Macs when we are expecting to
catch machine checks after poking at some random I/O address. I'd seen
it happen on my dual G4 with serial ports until we fixed those to use
OF, but now other users are reporting it with i8042.
This expands the use of check_legacy_ioport() to avoid that situation
even on 32-bit kernels.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
At present, ARCH=powerpc kernels can waste considerable space in
pagetables when making large hugepage mappings. Hugepage PTEs go in
PMD pages, but each PMD page maps 256M and so contains only 16
hugepage PTEs (128 bytes of data), but takes up a 1024 byte
allocation. With CONFIG_PPC_64K_PAGES enabled (64k base page size),
the situation is worse. Now hugepage PTEs are at the PTE page level
(also mapping 256M), so we store 16 hugepage PTEs in a 64k allocation.
The PowerPC MMU already means that any 256M region is either all
hugepage, or all normal pages. Thus, with some care, we can use a
different allocation for the hugepage PTE tables and only allocate the
128 bytes necessary.
Signed-off-by: Paul Mackerras <paulus@samba.org>
sys_splice() moves data to/from pipes with a file input/output. sys_vmsplice()
moves data to a pipe, with the input being a user address range instead.
This uses an approach suggested by Linus, where we can hold partial ranges
inside the pages[] map. Hopefully this will be useful for network
receive support as well.
Signed-off-by: Jens Axboe <axboe@suse.de>
machine_is() was always returning 0 when used in a module, because
we weren't exporting the machine definitions. This was why sound
wasn't working on powermacs when CONFIG_SND_POWERMAC=m. Original
fix from Ben Herrenschmidt, further fixed by me.
Signed-off-by: Paul Mackerras <paulus@samba.org>
The current PCI error recovery system keeps track of the number of PCI card
resets, and refuses to bring a card back up if this number is too large.
The goal of doing this was to avoid an infinite loop of resets if a card is
obviously dead. However, if the failures are rare, but the machine has a
high uptime, this mechanism might still be triggered; this is too harsh.
This patch will avoids this problem by decrementing the fail count after an
hour. Thus, as long as a pci card BSOD's less than 6 times an hour, it
will continue to be reset indefinitely. If it's failure rate is greater
than that, it will be taken off-line permanently.
This patch is larger than it might otherwise be because it changes
indentation by removing a pointless while-loop. The while loop is not
needed, as the handler is invoked once fo each event (by schedule_work());
the loop is leftover cruft from an earlier implementation.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Cleanup patch which removes the io_page_mask. It fixes the reset on
some e1000 devices which is needed for clean kexec reboots. The legacy
devices which broke with this patch (parallel port and PC speaker) have
now been fixed in Linus' tree.
Signed-off-by: Anton Blanchard <anton@samba.org>
Acked-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Some devices don't support full 32-bit DMA address space, which we currently
assume. Add the required mask-passing to the IOMMU allocators.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc-merge:
powerpc: Use correct sequence for putting CPU into nap mode
[PATCH] spufs: fix context-switch decrementer code
[PATCH] powerpc32: Set cpu explicitly in kernel compiles
[PATCH] powerpc/pseries: bugfix: balance calls to pci_device_put
[PATCH] powerpc: Fix machine detection in prom_init.c
[PATCH] ppc32: Fix string comparing in platform_notify_map
[PATCH] powerpc: Avoid __initcall warnings
[PATCH] powerpc: Ensure runlatch is off in the idle loop
powerpc: Fix CHRP booting - needs a define_machine call
powerpc: iSeries has only 256 IRQs
We weren't using the recommended sequence for putting the CPU into
nap mode. When I changed the idle loop, for some reason 7447A cpus
started hanging when we put them into nap mode. Changing to the
recommended sequence fixes that.
The complexity here is that the recommended sequence is a loop that
keeps putting the cpu back into nap mode. Clearly we need some way
to break out of the loop when an interrupt (external interrupt,
decrementer, performance monitor) occurs. Here we use a bit in
the thread_info struct to indicate that we need this, and the exception
entry code notices this and arranges for the exception to return
to the value in the link register, thus breaking out of the loop.
We use a new `local_flags' field in the thread_info which we can
alter without needing to use an atomic update sequence.
The PPC970 has the same recommended sequence, so we do the same thing
there too.
This also fixes a bug in the kernel stack overflow handling code on
32-bit, since it was causing a value that we needed in a register to
get trashed.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Basically an in-kernel implementation of tee, which uses splice and the
pipe buffers as an intelligent way to pass data around by reference.
Where the user space tee consumes the input and produces a stdout and
file output, this syscall merely duplicates the data inside a pipe to
another pipe. No data is copied, the output just grabs a reference to the
input pipe data.
Signed-off-by: Jens Axboe <axboe@suse.de>
Current implementations define NODES_SHIFT in include/asm-xxx/numnodes.h for
each arch. Its definition is sometimes configurable. Indeed, ia64 defines 5
NODES_SHIFT values in the current git tree. But it looks a bit messy.
SGI-SN2(ia64) system requires 1024 nodes, and the number of nodes already has
been changeable by config. Suitable node's number may be changed in the
future even if it is other architecture. So, I wrote configurable node's
number.
This patch set defines just default value for each arch which needs multi
nodes except ia64. But, it is easy to change to configurable if necessary.
On ia64 the number of nodes can be already configured in generic ia64 and SN2
config. But, NODES_SHIFT is defined for DIG64 and HP'S machine too. So, I
changed it so that all platforms can be configured via CONFIG_NODES_SHIFT. It
would be simpler.
See also: http://marc.theaimsgroup.com/?l=linux-kernel&m=114358010523896&w=2
Signed-off-by: Yasunori Goto <y-goto@jp.fujitsu.com>
Cc: Hirokazu Takata <takata@linux-m32r.org>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Andi Kleen <ak@muc.de>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Kyle McMartin <kyle@mcmartin.ca>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Jack Steiner <steiner@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The iSeries Hypervisor only allows us to specify IRQ numbers up to 255 (it
has a u8 field to pass it in). This patch allows platforms to specify a
maximum to the virtual IRQ numbers we will use and has iSeries set that
to 255. If not set, the maximum is NR_IRQS - 1 (as before).
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
This patch removes unnecessary exports, marks functions as static when
possible, and simplifies some list-related code.
Signed-off-by: Nathan Fontenot <nfont@austin.ibm.com>
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This extends the HCALL interface for InfiniBand usage. I've
made the patch against the linux-2.6 git tree and Segher's patch:
[PATCH] Change H_StudlyCaps to H_SHOUTING_CAPS
We moved this into the common powerpc code based on comments we
got after posting the first eHCA InfiniBand device driver patch.
Signed-off-by: Heiko j Schick <schickhj@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Also cleans up some nearby whitespace problems.
Signed-off-by: Segher Boessenkool <segher@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Previously we added NET_IP_ALIGN so an architecture can override the
padding done to align headers. The next step is to allow the skb
headroom to be overridden.
We currently always reserve 16 bytes to grow into, meaning all DMAs
start 16 bytes into a cacheline. On ppc64 we really want DMA writes to
start on a cacheline boundary, so we increase that headroom to one
cacheline.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds support for the sys_splice system call. Using a pipe as a
transport, it can connect to files or sockets (latter as output only).
From the splice.c comments:
"splice": joining two ropes together by interweaving their strands.
This is the "extended pipe" functionality, where a pipe is used as
an arbitrary in-memory buffer. Think of a pipe as a small kernel
buffer that you can use to transfer data from one end to the other.
The traditional unix read/write is extended with a "splice()" operation
that transfers data buffers to or from a pipe buffer.
Named by Larry McVoy, original implementation from Linus, extended by
Jens to support splicing to files and fixing the initial implementation
bugs.
Signed-off-by: Jens Axboe <axboe@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Remove oprofile spinlock backtrace code now we have proper calltrace
support. Also make MMCRA sihv and sipr bits a variable since they may
change in future cpus. Finally, MMCRA should be a 64bit quantity.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Add oprofile calltrace support to powerpc. Disable spinlock backtracing
now we can use calltrace info.
(Updated to work on both 32bit and 64bit by me).
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
for_each_cpu() actually iterates across all possible CPUs. We've had mistakes
in the past where people were using for_each_cpu() where they should have been
iterating across only online or present CPUs. This is inefficient and
possibly buggy.
We're renaming for_each_cpu() to for_each_possible_cpu() to avoid this in the
future.
This patch replaces for_each_cpu with for_each_possible_cpu.
Signed-off-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This removes statically assigned platform numbers and reworks the
powerpc platform probe code to use a better mechanism. With this,
board support files can simply declare a new machine type with a
macro, and implement a probe() function that uses the flattened
device-tree to detect if they apply for a given machine.
We now have a machine_is() macro that replaces the comparisons of
_machine with the various PLATFORM_* constants. This commit also
changes various drivers to use the new macro instead of looking at
_machine.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
There are at least 14 different implementations of WARN() in the tree already.
The build fails all over the place.
Cc: Paul Mackerras <paulus@samba.org>
Cc: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
We used to assume that a DMA mapping request with a NULL dev was for
ISA DMA. This assumption was broken at some point. Now we explicitly
pass the detected ISA PCI device in the floppy setup.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
These are some updates from both Ryan and Arnd for the hvc_console
driver:
The main point is to enable the inclusion of a console driver
for rtas, which is currrently needed for the cell platform.
Also shuffle around some data-type declarations and moves some
functions out of include/asm-ppc64/hvconsole.h and into a new
drivers/char/hvc_console.h file.
Signed-off-by: "Ryan S. Arnold" <rsa@us.ibm.com>
Signed-off-by: Arnd Bergmann <abergman@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
We need to export ppc64_firmware_features for modules. Before we do that
I think we should probably rename it to powerpc_firmware_features.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Export validate_sp so we can use it in the oprofile calltrace code.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
- No one uses op_counter_config.valid, so remove it
- No need to ifdef around function protypes.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
32-bit CHRP machines are now supported only in arch/powerpc, as are
all 64-bit PowerPC processors. This means that we don't use
Open Firmware on any platform in arch/ppc any more.
This makes PReP support a single-platform option like every other
platform support option in arch/ppc now, thus CONFIG_PPC_MULTIPLATFORM
is gone from arch/ppc. CONFIG_PPC_PREP is the option that selects
PReP support and is generally what has replaced
CONFIG_PPC_MULTIPLATFORM within arch/ppc.
_machine is all but dead now, being #defined to 0.
Updated Makefiles, comments and Kconfig options generally to reflect
these changes.
Signed-off-by: Paul Mackerras <paulus@samba.org>
The kernel's implementation of notifier chains is unsafe. There is no
protection against entries being added to or removed from a chain while the
chain is in use. The issues were discussed in this thread:
http://marc.theaimsgroup.com/?l=linux-kernel&m=113018709002036&w=2
We noticed that notifier chains in the kernel fall into two basic usage
classes:
"Blocking" chains are always called from a process context
and the callout routines are allowed to sleep;
"Atomic" chains can be called from an atomic context and
the callout routines are not allowed to sleep.
We decided to codify this distinction and make it part of the API. Therefore
this set of patches introduces three new, parallel APIs: one for blocking
notifiers, one for atomic notifiers, and one for "raw" notifiers (which is
really just the old API under a new name). New kinds of data structures are
used for the heads of the chains, and new routines are defined for
registration, unregistration, and calling a chain. The three APIs are
explained in include/linux/notifier.h and their implementation is in
kernel/sys.c.
With atomic and blocking chains, the implementation guarantees that the chain
links will not be corrupted and that chain callers will not get messed up by
entries being added or removed. For raw chains the implementation provides no
guarantees at all; users of this API must provide their own protections. (The
idea was that situations may come up where the assumptions of the atomic and
blocking APIs are not appropriate, so it should be possible for users to
handle these things in their own way.)
There are some limitations, which should not be too hard to live with. For
atomic/blocking chains, registration and unregistration must always be done in
a process context since the chain is protected by a mutex/rwsem. Also, a
callout routine for a non-raw chain must not try to register or unregister
entries on its own chain. (This did happen in a couple of places and the code
had to be changed to avoid it.)
Since atomic chains may be called from within an NMI handler, they cannot use
spinlocks for synchronization. Instead we use RCU. The overhead falls almost
entirely in the unregister routine, which is okay since unregistration is much
less frequent that calling a chain.
Here is the list of chains that we adjusted and their classifications. None
of them use the raw API, so for the moment it is only a placeholder.
ATOMIC CHAINS
-------------
arch/i386/kernel/traps.c: i386die_chain
arch/ia64/kernel/traps.c: ia64die_chain
arch/powerpc/kernel/traps.c: powerpc_die_chain
arch/sparc64/kernel/traps.c: sparc64die_chain
arch/x86_64/kernel/traps.c: die_chain
drivers/char/ipmi/ipmi_si_intf.c: xaction_notifier_list
kernel/panic.c: panic_notifier_list
kernel/profile.c: task_free_notifier
net/bluetooth/hci_core.c: hci_notifier
net/ipv4/netfilter/ip_conntrack_core.c: ip_conntrack_chain
net/ipv4/netfilter/ip_conntrack_core.c: ip_conntrack_expect_chain
net/ipv6/addrconf.c: inet6addr_chain
net/netfilter/nf_conntrack_core.c: nf_conntrack_chain
net/netfilter/nf_conntrack_core.c: nf_conntrack_expect_chain
net/netlink/af_netlink.c: netlink_chain
BLOCKING CHAINS
---------------
arch/powerpc/platforms/pseries/reconfig.c: pSeries_reconfig_chain
arch/s390/kernel/process.c: idle_chain
arch/x86_64/kernel/process.c idle_notifier
drivers/base/memory.c: memory_chain
drivers/cpufreq/cpufreq.c cpufreq_policy_notifier_list
drivers/cpufreq/cpufreq.c cpufreq_transition_notifier_list
drivers/macintosh/adb.c: adb_client_list
drivers/macintosh/via-pmu.c sleep_notifier_list
drivers/macintosh/via-pmu68k.c sleep_notifier_list
drivers/macintosh/windfarm_core.c wf_client_list
drivers/usb/core/notify.c usb_notifier_list
drivers/video/fbmem.c fb_notifier_list
kernel/cpu.c cpu_chain
kernel/module.c module_notify_list
kernel/profile.c munmap_notifier
kernel/profile.c task_exit_notifier
kernel/sys.c reboot_notifier_list
net/core/dev.c netdev_chain
net/decnet/dn_dev.c: dnaddr_chain
net/ipv4/devinet.c: inetaddr_chain
It's possible that some of these classifications are wrong. If they are,
please let us know or submit a patch to fix them. Note that any chain that
gets called very frequently should be atomic, because the rwsem read-locking
used for blocking chains is very likely to incur cache misses on SMP systems.
(However, if the chain's callout routines may sleep then the chain cannot be
atomic.)
The patch set was written by Alan Stern and Chandra Seetharaman, incorporating
material written by Keith Owens and suggestions from Paul McKenney and Andrew
Morton.
[jes@sgi.com: restructure the notifier chain initialization macros]
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Chandra Seetharaman <sekharan@us.ibm.com>
Signed-off-by: Jes Sorensen <jes@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- fix: initialize the robust list(s) to NULL in copy_process.
- doc update
- cleanup: rename _inuser to _inatomic
- __user cleanups and other small cleanups
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Arjan van de Ven <arjan@infradead.org>
Cc: Ulrich Drepper <drepper@redhat.com>
Cc: Andi Kleen <ak@muc.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patchset provides a new (written from scratch) implementation of robust
futexes, called "lightweight robust futexes". We believe this new
implementation is faster and simpler than the vma-based robust futex solutions
presented before, and we'd like this patchset to be adopted in the upstream
kernel. This is version 1 of the patchset.
Background
----------
What are robust futexes? To answer that, we first need to understand what
futexes are: normal futexes are special types of locks that in the
noncontended case can be acquired/released from userspace without having to
enter the kernel.
A futex is in essence a user-space address, e.g. a 32-bit lock variable
field. If userspace notices contention (the lock is already owned and someone
else wants to grab it too) then the lock is marked with a value that says
"there's a waiter pending", and the sys_futex(FUTEX_WAIT) syscall is used to
wait for the other guy to release it. The kernel creates a 'futex queue'
internally, so that it can later on match up the waiter with the waker -
without them having to know about each other. When the owner thread releases
the futex, it notices (via the variable value) that there were waiter(s)
pending, and does the sys_futex(FUTEX_WAKE) syscall to wake them up. Once all
waiters have taken and released the lock, the futex is again back to
'uncontended' state, and there's no in-kernel state associated with it. The
kernel completely forgets that there ever was a futex at that address. This
method makes futexes very lightweight and scalable.
"Robustness" is about dealing with crashes while holding a lock: if a process
exits prematurely while holding a pthread_mutex_t lock that is also shared
with some other process (e.g. yum segfaults while holding a pthread_mutex_t,
or yum is kill -9-ed), then waiters for that lock need to be notified that the
last owner of the lock exited in some irregular way.
To solve such types of problems, "robust mutex" userspace APIs were created:
pthread_mutex_lock() returns an error value if the owner exits prematurely -
and the new owner can decide whether the data protected by the lock can be
recovered safely.
There is a big conceptual problem with futex based mutexes though: it is the
kernel that destroys the owner task (e.g. due to a SEGFAULT), but the kernel
cannot help with the cleanup: if there is no 'futex queue' (and in most cases
there is none, futexes being fast lightweight locks) then the kernel has no
information to clean up after the held lock! Userspace has no chance to clean
up after the lock either - userspace is the one that crashes, so it has no
opportunity to clean up. Catch-22.
In practice, when e.g. yum is kill -9-ed (or segfaults), a system reboot is
needed to release that futex based lock. This is one of the leading
bugreports against yum.
To solve this problem, 'Robust Futex' patches were created and presented on
lkml: the one written by Todd Kneisel and David Singleton is the most advanced
at the moment. These patches all tried to extend the futex abstraction by
registering futex-based locks in the kernel - and thus give the kernel a
chance to clean up.
E.g. in David Singleton's robust-futex-6.patch, there are 3 new syscall
variants to sys_futex(): FUTEX_REGISTER, FUTEX_DEREGISTER and FUTEX_RECOVER.
The kernel attaches such robust futexes to vmas (via
vma->vm_file->f_mapping->robust_head), and at do_exit() time, all vmas are
searched to see whether they have a robust_head set.
Lots of work went into the vma-based robust-futex patch, and recently it has
improved significantly, but unfortunately it still has two fundamental
problems left:
- they have quite complex locking and race scenarios. The vma-based
patches had been pending for years, but they are still not completely
reliable.
- they have to scan _every_ vma at sys_exit() time, per thread!
The second disadvantage is a real killer: pthread_exit() takes around 1
microsecond on Linux, but with thousands (or tens of thousands) of vmas every
pthread_exit() takes a millisecond or more, also totally destroying the CPU's
L1 and L2 caches!
This is very much noticeable even for normal process sys_exit_group() calls:
the kernel has to do the vma scanning unconditionally! (this is because the
kernel has no knowledge about how many robust futexes there are to be cleaned
up, because a robust futex might have been registered in another task, and the
futex variable might have been simply mmap()-ed into this process's address
space).
This huge overhead forced the creation of CONFIG_FUTEX_ROBUST, but worse than
that: the overhead makes robust futexes impractical for any type of generic
Linux distribution.
So it became clear to us, something had to be done. Last week, when Thomas
Gleixner tried to fix up the vma-based robust futex patch in the -rt tree, he
found a handful of new races and we were talking about it and were analyzing
the situation. At that point a fundamentally different solution occured to
me. This patchset (written in the past couple of days) implements that new
solution. Be warned though - the patchset does things we normally dont do in
Linux, so some might find the approach disturbing. Parental advice
recommended ;-)
New approach to robust futexes
------------------------------
At the heart of this new approach there is a per-thread private list of robust
locks that userspace is holding (maintained by glibc) - which userspace list
is registered with the kernel via a new syscall [this registration happens at
most once per thread lifetime]. At do_exit() time, the kernel checks this
user-space list: are there any robust futex locks to be cleaned up?
In the common case, at do_exit() time, there is no list registered, so the
cost of robust futexes is just a simple current->robust_list != NULL
comparison. If the thread has registered a list, then normally the list is
empty. If the thread/process crashed or terminated in some incorrect way then
the list might be non-empty: in this case the kernel carefully walks the list
[not trusting it], and marks all locks that are owned by this thread with the
FUTEX_OWNER_DEAD bit, and wakes up one waiter (if any).
The list is guaranteed to be private and per-thread, so it's lockless. There
is one race possible though: since adding to and removing from the list is
done after the futex is acquired by glibc, there is a few instructions window
for the thread (or process) to die there, leaving the futex hung. To protect
against this possibility, userspace (glibc) also maintains a simple per-thread
'list_op_pending' field, to allow the kernel to clean up if the thread dies
after acquiring the lock, but just before it could have added itself to the
list. Glibc sets this list_op_pending field before it tries to acquire the
futex, and clears it after the list-add (or list-remove) has finished.
That's all that is needed - all the rest of robust-futex cleanup is done in
userspace [just like with the previous patches].
Ulrich Drepper has implemented the necessary glibc support for this new
mechanism, which fully enables robust mutexes. (Ulrich plans to commit these
changes to glibc-HEAD later today.)
Key differences of this userspace-list based approach, compared to the vma
based method:
- it's much, much faster: at thread exit time, there's no need to loop
over every vma (!), which the VM-based method has to do. Only a very
simple 'is the list empty' op is done.
- no VM changes are needed - 'struct address_space' is left alone.
- no registration of individual locks is needed: robust mutexes dont need
any extra per-lock syscalls. Robust mutexes thus become a very lightweight
primitive - so they dont force the application designer to do a hard choice
between performance and robustness - robust mutexes are just as fast.
- no per-lock kernel allocation happens.
- no resource limits are needed.
- no kernel-space recovery call (FUTEX_RECOVER) is needed.
- the implementation and the locking is "obvious", and there are no
interactions with the VM.
Performance
-----------
I have benchmarked the time needed for the kernel to process a list of 1
million (!) held locks, using the new method [on a 2GHz CPU]:
- with FUTEX_WAIT set [contended mutex]: 130 msecs
- without FUTEX_WAIT set [uncontended mutex]: 30 msecs
I have also measured an approach where glibc does the lock notification [which
it currently does for !pshared robust mutexes], and that took 256 msecs -
clearly slower, due to the 1 million FUTEX_WAKE syscalls userspace had to do.
(1 million held locks are unheard of - we expect at most a handful of locks to
be held at a time. Nevertheless it's nice to know that this approach scales
nicely.)
Implementation details
----------------------
The patch adds two new syscalls: one to register the userspace list, and one
to query the registered list pointer:
asmlinkage long
sys_set_robust_list(struct robust_list_head __user *head,
size_t len);
asmlinkage long
sys_get_robust_list(int pid, struct robust_list_head __user **head_ptr,
size_t __user *len_ptr);
List registration is very fast: the pointer is simply stored in
current->robust_list. [Note that in the future, if robust futexes become
widespread, we could extend sys_clone() to register a robust-list head for new
threads, without the need of another syscall.]
So there is virtually zero overhead for tasks not using robust futexes, and
even for robust futex users, there is only one extra syscall per thread
lifetime, and the cleanup operation, if it happens, is fast and
straightforward. The kernel doesnt have any internal distinction between
robust and normal futexes.
If a futex is found to be held at exit time, the kernel sets the highest bit
of the futex word:
#define FUTEX_OWNER_DIED 0x40000000
and wakes up the next futex waiter (if any). User-space does the rest of
the cleanup.
Otherwise, robust futexes are acquired by glibc by putting the TID into the
futex field atomically. Waiters set the FUTEX_WAITERS bit:
#define FUTEX_WAITERS 0x80000000
and the remaining bits are for the TID.
Testing, architecture support
-----------------------------
I've tested the new syscalls on x86 and x86_64, and have made sure the parsing
of the userspace list is robust [ ;-) ] even if the list is deliberately
corrupted.
i386 and x86_64 syscalls are wired up at the moment, and Ulrich has tested the
new glibc code (on x86_64 and i386), and it works for his robust-mutex
testcases.
All other architectures should build just fine too - but they wont have the
new syscalls yet.
Architectures need to implement the new futex_atomic_cmpxchg_inuser() inline
function before writing up the syscalls (that function returns -ENOSYS right
now).
This patch:
Add placeholder futex_atomic_cmpxchg_inuser() implementations to every
architecture that supports futexes. It returns -ENOSYS.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Arjan van de Ven <arjan@infradead.org>
Acked-by: Ulrich Drepper <drepper@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
PowerPC can use generic ones.
Signed-off-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
On CHRP machines we are supposed to call into firmware (RTAS)
periodically, to give it a chance to check for errors and other
events. Under ppc we had some special code in timer_interrupt
to do this, but that didn't get transferred over to arch/powerpc.
Instead, we use an array of timer_list structs, one per CPU,
and use add_timer_on to make sure each one gets called on the
appropriate CPU.
With this we can remove the heartbeat_* elements of the ppc_md
struct.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Since pSeries only wants to do something different in the idle loop when
there is no work to do, we can simplify the code by implementing
ppc_md.power_save functions instead of complete idle loops. There are
two versions: one for shared-processor partitions and one for dedicated-
processor partitions.
With this we also do a cede_processor() call on dedicated processor
partitions if the poll_pending() call indicates that the hypervisor
has work it wants to do.
Signed-off-by: Paul Mackerras <paulus@samba.org>
This unifies the 32-bit (ARCH=ppc and ARCH=powerpc) and 64-bit idle
loops. It brings over the concept of having a ppc_md.power_save
function from 32-bit to ARCH=powerpc, which lets us get rid of
native_idle(). With this we will also be able to simplify the idle
handling for pSeries and cell.
Signed-off-by: Paul Mackerras <paulus@samba.org>
We currently have a hack to flip the boot cpu and its secondary thread
to logical cpuid 0 and 1. This means the logical - physical mapping will
differ depending on which cpu is boot cpu. This is most apparent on
kexec, where we might kexec on any cpu and therefore change the mapping
from boot to boot.
The patch below does a first pass early on to work out the logical cpuid
of the boot thread. We then fix up some paca structures to match.
Ive also removed the boot_cpuid_phys variable for ppc64, to be
consistent we use get_hard_smp_processor_id(boot_cpuid) everywhere.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch is layered on top of CONFIG_SPARSEMEM
and is patterned after direct mapping of LS.
This patch allows mmap() of the following regions:
"mfc", which represents the area from [0x3000 - 0x3fff];
"cntl", which represents the area from [0x4000 - 0x4fff];
"signal1" which begins at offset 0x14000; "signal2" which
begins at offset 0x1c000.
The signal1 & signal2 files may be mmap()'d by regular user
processes. The cntl and mfc file, on the other hand, may
only be accessed if the owning process has CAP_SYS_RAWIO,
because they have the potential to confuse the kernel
with regard to parallel access to the same files with
regular file operations: the kernel always holds a spinlock
when accessing registers in these areas to serialize them,
which can not be guaranteed with user mmaps,
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch adds a new file called 'mfc' to each spufs directory.
The file accepts DMA commands that are a subset of what would
be legal DMA commands for problem state register access. Upon
reading the file, a bitmask is returned with the completed
tag groups set.
The file is meant to be used from an abstraction in libspe
that is added by a different patch.
From the kernel perspective, this means a process can now
offload a memory copy from or into an SPE local store
without having to run code on the SPE itself.
The transfer will only be performed while the SPE is owned
by one thread that is waiting in the spu_run system call
and the data will be transferred into that thread's
address space, independent of which thread started the
transfer.
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
An SPU does not have a way to implement system calls
itself, but it can create intercepts to the kernel.
This patch uses the method defined by the JSRE interface
for C99 host library calls from an SPU to implement
Linux system calls. It uses the reserved SPU stop code
0x2104 for this, using the structure layout and syscall
numbers for ppc64-linux.
I'm still undecided wether it is better to have a list
of allowed syscalls or a list of forbidden syscalls,
since we can't allow an SPU to call all syscalls that
are defined for ppc64-linux.
This patch implements the easier choice of them, with a
blacklist that only prevents an SPU from calling anything
that interacts with its own execution, e.g fork, execve,
clone, vfork, exit, spu_run and spu_create and everything
that deals with signals.
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
powerpc currently declares some of its own system calls
in <asm/unistd.h>, but not all of them. That place also
contains remainders of the now almost unused kernel syscall
hack.
- Add a new <asm/syscalls.h> with clean declarations
- Include that file from every source that implements one
of these
- Get rid of old declarations in <asm/unistd.h>
This patch is required as a base for implementing system
calls from an SPU, but also makes sense as a general
cleanup.
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
So that we can use firmware_has_feature() in a BUG_ON() and have the compiler
elide the code entirely if the feature can never be set, change
firmware_has_feature to a macro. Unfortunate, but necessary at least until
GCC bug #26724 is fixed.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Change BUG_ON and WARN_ON to give the compiler a chance to perform
compile-time optimsations. Depending on the complexity of the condition,
the compiler may not do this very well, so if it's important check the
object code.
Current GCC's (4.x) produce good code as long as the condition does not
include a function call, including a static inline.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Christoph noticed that sparse warned about all the enum tags in cuptable.h
that had values that required them to be type log. (enum tags are ints
according to the standard.)
This patch attempts to fix them in the least intrusive way possible by
turning them all into #defines except for the 32 bit CPU_FTRS_POSSIBLE and
CPU_FTRS_ALWAYS which are hard to construct that way. This works because
these last two contain no bits above 2^31.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Add blkcnt_t as the type of inode.i_blocks. This enables you to make the size
of blkcnt_t either 4 bytes or 8 bytes on 32 bits architecture with CONFIG_LSF.
- CONFIG_LSF
Add new configuration parameter.
- blkcnt_t
On h8300, i386, mips, powerpc, s390 and sh that define sector_t,
blkcnt_t is defined as u64 if CONFIG_LSF is enabled; otherwise it is
defined as unsigned long.
On other architectures, it is defined as unsigned long.
- inode.i_blocks
Change the type from sector_t to blkcnt_t.
Signed-off-by: Takashi Sato <sho@tnes.nec.co.jp>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Implement the half-closed devices notifiation, by adding a new POLLRDHUP
(and its alias EPOLLRDHUP) bit to the existing poll/select sets. Since the
existing POLLHUP handling, that does not report correctly half-closed
devices, was feared to be changed, this implementation leaves the current
POLLHUP reporting unchanged and simply add a new bit that is set in the few
places where it makes sense. The same thing was discussed and conceptually
agreed quite some time ago:
http://lkml.org/lkml/2003/7/12/116
Since this new event bit is added to the existing Linux poll infrastruture,
even the existing poll/select system calls will be able to use it. As far
as the existing POLLHUP handling, the patch leaves it as is. The
pollrdhup-2.6.16.rc5-0.10.diff defines the POLLRDHUP for all the existing
archs and sets the bit in the six relevant files. The other attached diff
is the simple change required to sys/epoll.h to add the EPOLLRDHUP
definition.
There is "a stupid program" to test POLLRDHUP delivery here:
http://www.xmailserver.org/pollrdhup-test.c
It tests poll(2), but since the delivery is same epoll(2) will work equally.
Signed-off-by: Davide Libenzi <davidel@xmailserver.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Michael Kerrisk <mtk-manpages@gmx.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
When we stop allocating percpu memory for not-possible CPUs we must not touch
the percpu data for not-possible CPUs at all. The correct way of doing this
is to test cpu_possible() or to use for_each_cpu().
This patch is a kernel-wide sweep of all instances of NR_CPUS. I found very
few instances of this bug, if any. But the patch converts lots of open-coded
test to use the preferred helper macros.
Cc: Mikael Starvik <starvik@axis.com>
Cc: David Howells <dhowells@redhat.com>
Acked-by: Kyle McMartin <kyle@parisc-linux.org>
Cc: Anton Blanchard <anton@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: William Lee Irwin III <wli@holomorphy.com>
Cc: Andi Kleen <ak@muc.de>
Cc: Christian Zankel <chris@zankel.net>
Cc: Philippe Elie <phil.el@wanadoo.fr>
Cc: Nathan Scott <nathans@sgi.com>
Cc: Jens Axboe <axboe@suse.de>
Cc: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
free_pgtables() has special logic to call hugetlb_free_pgd_range() instead
of the normal free_pgd_range() on hugepage VMAs. However, the test it uses
to do so is incorrect: it calls is_hugepage_only_range on a hugepage sized
range at the start of the vma. is_hugepage_only_range() will return true
if the given range has any intersection with a hugepage address region, and
in this case the given region need not be hugepage aligned. So, for
example, this test can return true if called on, say, a 4k VMA immediately
preceding a (nicely aligned) hugepage VMA.
At present we get away with this because the powerpc version of
hugetlb_free_pgd_range() is just a call to free_pgd_range(). On ia64 (the
only other arch with a non-trivial is_hugepage_only_range()) we get away
with it for a different reason; the hugepage area is not contiguous with
the rest of the user address space, and VMAs are not permitted in between,
so the test can't return a false positive there.
Nonetheless this should be fixed. We do that in the patch below by
replacing the is_hugepage_only_range() test with an explicit test of the
VMA using is_vm_hugetlb_page().
This in turn changes behaviour for platforms where is_hugepage_only_range()
returns false always (everything except powerpc and ia64). We address this
by ensuring that hugetlb_free_pgd_range() is defined to be identical to
free_pgd_range() (instead of a no-op) on everything except ia64. Even so,
it will prevent some otherwise possible coalescing of calls down to
free_pgd_range(). Since this only happens for hugepage VMAs, removing this
small optimization seems unlikely to cause any trouble.
This patch causes no regressions on the libhugetlbfs testsuite - ppc64
POWER5 (8-way), ppc64 G5 (2-way) and i386 Pentium M (UP).
Signed-off-by: David Gibson <dwg@au1.ibm.com>
Cc: William Lee Irwin III <wli@holomorphy.com>
Acked-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
In mm_init_ppc64() we calculate the location of the "IO hole", but then
no one ever looks at the value. So don't bother.
That's actually all mm_init_ppc64() does, so get rid of it too.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Add strne2a() which converts a string from EBCDIC to ASCII.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Make mf_get_rtc(), mf_get_boot_rtc() and mf_set_rtc() static, cause they can
be. We need to move mf_set_rtc() to avoid a forward declaration.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
These routines just call through to the mf routines, so point ppc_md straight
at the mf routines. We need to pass the cmd through to mf_reboot to make it
work, but that seems reasonable.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Some cleanups in the iSeries code.
- Make mf_display_progress() check mf_initialized rather than the caller.
- Set mf_initialized in mf_init() rather than in setup.c
- Then move mf_initialized into mf.c, the only place it's used.
- Move the mf related logic from iSeries_progress() to mf_display_progress()
- Use a #define to size the pending_event_prealloc array
- Use that define in the initialsation loop rather than sizeof jiggery pokery
- Remove stupid comment(s)
- Mark stuff static and/or __init
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
It has been decreed that platform numbers are evil, so as a step in that
direction, replace platform_is_lpar() with a FW_FEATURE_LPAR bit.
Currently FW_FEATURE_LPAR really means i/pSeries LPAR, in the future we might
have to clean that up if we need to be more specific about what LPAR actually
means. But that's another patch ...
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Remove redundant whitespace in include/asm-powerpc/cputable.h
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Typical use for of_find_node_by_name and of_find_node_by_type is to
iterate over all nodes of a given type/name. Add a helper macro to
do that (in spirit of the list_for_each* macros).
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
At present, the powerpc pmd_bad() and pud_bad() macros return false
unless the given pmd or pud is zero. This patch makes these tests
more thorough, checking if the given pmd or pud looks like a plausible
pte page or pmd page pointer respectively. This can result in helpful
error messages when messing with the pagetable code.
Signed-off-by: David Gibson <dwg@au1.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The dynamic add path for PCI Host Bridges can fail to configure children
adapters under P5IOC controllers. It fails to properly fixup bus/device
resources, and it fails to properly enable EEH. Both of these steps
need to occur before any children devices are enabled in
pci_bus_add_devices().
Signed-off-by: John Rose <johnrose@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
While testing kexec and kdump we hit problems where the new kernel would
freeze or instantly reboot. The easiest way to trigger it was to kexec a
kernel compiled for CONFIG_M586 on an athlon cpu. Compiling for CONFIG_MK7
instead would work fine.
The patch fixes a few problems with the kexec inline asm.
Signed-off-by: Chris Mason <mason@suse.com>
Acked-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
We fixed this:
arch/powerpc/platforms/pseries/eeh.c: In function `eeh_add_device_tree_late':
arch/powerpc/platforms/pseries/eeh.c:901: warning: implicit declaration of function `eeh_add_device_late'
arch/powerpc/platforms/pseries/eeh.c: At top level:
arch/powerpc/platforms/pseries/eeh.c:918: error: conflicting types for 'eeh_add_device_late'
arch/powerpc/platforms/pseries/eeh.c:901: error: previous implicit declaration of 'eeh_add_device_late' was here
make[2]: *** [arch/powerpc/platforms/pseries/eeh.o] Error 1
But we forgot the !CONFIG_EEH stub.
Signed-off-by: Mark Fasheh <mark.fasheh@oracle.com>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
A careful reading of the recent changes to the system call entry/exit
paths revealed several problems, plus some things that could be
simplified and improved:
* 32-bit wasn't testing the _TIF_NOERROR bit in the syscall fast exit
path, so it was only doing anything with it once it saw some other
bit being set. In other words, the noerror behaviour would apply to
the next system call where we had to reschedule or deliver a signal,
which is not necessarily the current system call.
* 32-bit wasn't doing the call to ptrace_notify in the syscall exit
path when the _TIF_SINGLESTEP bit was set.
* _TIF_RESTOREALL was in both _TIF_USER_WORK_MASK and
_TIF_PERSYSCALL_MASK, which is odd since _TIF_RESTOREALL is only set
by system calls. I took it out of _TIF_USER_WORK_MASK.
* On 64-bit, _TIF_RESTOREALL wasn't causing the non-volatile registers
to be restored (unless perhaps a signal was delivered or the syscall
was traced or single-stepped). Thus the non-volatile registers
weren't restored on exit from a signal handler. We probably got
away with it mostly because signal handlers written in C wouldn't
alter the non-volatile registers.
* On 32-bit I simplified the code and made it more like 64-bit by
making the syscall exit path jump to ret_from_except to handle
preemption and signal delivery.
* 32-bit was calling do_signal unnecessarily when _TIF_RESTOREALL was
set - but I think because of that 32-bit was actually restoring the
non-volatile registers on exit from a signal handler.
* I changed the order of enabling interrupts and saving the
non-volatile registers before calling do_syscall_trace_leave; now we
enable interrupts first.
Signed-off-by: Paul Mackerras <paulus@samba.org>
The powerpc pud_ERROR() function misleadingly prints a message
indicating a pmd error. This patch fixes it.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch makes userland aware of the icache snoop capability of the
POWER5 (and possibly others in the future) and of SMT capabilities.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch should fixe a problem with eeh_add_device_late() not being
defined in the ppc64 build process, causing the build to break.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Some hotplug driver functions were migrated to the kernel for use by EEH
in commit 2bf6a8fa21.
Previously, the PCI Hotplug module had been changed to use the new
OFDT-based PCI probe when appropriate:
5fa80fcdca
When rpaphp_pci_config_slot() was moved from the rpaphp driver to the
new kernel function pcibios_add_pci_devices(), the OFDT-based probe
stuff was dropped. This patch restores it.
Signed-off-by: John Rose <johnrose@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Do atomic_add_unless natively instead of using cmpxchg.
Improved register allocation idea from Joel Schopp.
Signed-off-by: Nick Piggin <npiggin@suse.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Add a newline at the end of the ISYNC_ON_SMP string.
Needed for a subsequent patch.
Signed-off-by: Nick Piggin <npiggin@suse.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Currently ARCH=powerpc will not compile when STRICT_MM_TYPECHECKS is
turned on and CONFIG_64K_PAGES is turned off. This corrects the
problem.
Signed-off-by: David Gibson <dwg@au1.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This implements accurate task and cpu time accounting for 64-bit
powerpc kernels. Instead of accounting a whole jiffy of time to a
task on a timer interrupt because that task happened to be running at
the time, we now account time in units of timebase ticks according to
the actual time spent by the task in user mode and kernel mode. We
also count the time spent processing hardware and software interrupts
accurately. This is conditional on CONFIG_VIRT_CPU_ACCOUNTING. If
that is not set, we do tick-based approximate accounting as before.
To get this accurate information, we read either the PURR (processor
utilization of resources register) on POWER5 machines, or the timebase
on other machines on
* each entry to the kernel from usermode
* each exit to usermode
* transitions between process context, hard irq context and soft irq
context in kernel mode
* context switches.
On POWER5 systems with shared-processor logical partitioning we also
read both the PURR and the timebase at each timer interrupt and
context switch in order to determine how much time has been taken by
the hypervisor to run other partitions ("steal" time). Unfortunately,
since we need values of the PURR on both threads at the same time to
accurately calculate the steal time, and since we can only calculate
steal time on a per-core basis, the apportioning of the steal time
between idle time (time which we ceded to the hypervisor in the idle
loop) and actual stolen time is somewhat approximate at the moment.
This is all based quite heavily on what s390 does, and it uses the
generic interfaces that were added by the s390 developers,
i.e. account_system_time(), account_user_time(), etc.
This patch doesn't add any new interfaces between the kernel and
userspace, and doesn't change the units in which time is reported to
userspace by things such as /proc/stat, /proc/<pid>/stat, getrusage(),
times(), etc. Internally the various task and cpu times are stored in
timebase units, but they are converted to USER_HZ units (1/100th of a
second) when reported to userspace. Some precision is therefore lost
but there should not be any accumulating error, since the internal
accumulation is at full precision.
Signed-off-by: Paul Mackerras <paulus@samba.org>
The runlatch SPR can take a lot of time to write. My original runlatch
code would set it on every exception entry even though most of the time
this was not required. It would also continually set it in the idle
loop, which is an issue on an SMT capable processor.
Now we cache the runlatch value in a threadinfo bit, and only check for
it in decrementer and hardware interrupt exceptions as well as the idle
loop. Boot on POWER3, POWER5 and iseries, and compile tested on pmac32.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
On the 83xx platform to ensure the PCI inbound memory is handled properly we
have to turn on coherency for all pages in the MMU. Otherwise we see
corruption if inbound "prefetching/streaming" is enabled on the PCI controller.
Signed-off-by: Randy Vinson <rvinson@mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
For kexec we need to know the size of the MMU hash table.
Currently we calculate the size once in the htab code, and then twice more in
the kexec code, once using htab_hash_mask and once using ppc64_pft_size.
On some machines the ppc64_pft_size calculation is broken because
ppc64_pft_size is not set.
So we need to fix the second calculation, but better still we should just
calculate the size once and use it everywhere else.
Tested on Power5 LPAR, Power4 non-LPAR and Power3.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
One of the parameters to the __pud_free_tlb() macro for powerpc is
incorrect (see patch) . We get away with it by accident, because the one
place the macro is called, the second parameter is a variable named "pud".
Signed-off-by: David Gibson <dwg@au1.ibm.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Make new MADV_REMOVE, MADV_DONTFORK, MADV_DOFORK consistent across all
arches. The idea is to make it possible to use them portably even before
distros include them in libc headers.
Move common flags to asm-generic/mman.h
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Cc: Roland Dreier <rolandd@cisco.com>
Cc: Badari Pulavarty <pbadari@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Currently, copy-on-write may change the physical address of a page even if the
user requested that the page is pinned in memory (either by mlock or by
get_user_pages). This happens if the process forks meanwhile, and the parent
writes to that page. As a result, the page is orphaned: in case of
get_user_pages, the application will never see any data hardware DMA's into
this page after the COW. In case of mlock'd memory, the parent is not getting
the realtime/security benefits of mlock.
In particular, this affects the Infiniband modules which do DMA from and into
user pages all the time.
This patch adds madvise options to control whether memory range is inherited
across fork. Useful e.g. for when hardware is doing DMA from/into these
pages. Could also be useful to an application wanting to speed up its forks
by cutting large areas out of consideration.
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Acked-by: Hugh Dickins <hugh@veritas.com>
Cc: Michael Kerrisk <mtk-manpages@gmx.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch removes all self references and fixes references to files
in the now defunct arch/ppc64 tree. I think this accomplises
everything wanted, though there might be a few references I missed.
Signed-off-by: Jon Mason <jdmason@us.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Currently we have some stuff in firmware.h and kernel/firmware.c that is
#ifdef CONFIG_PPC_PSERIES. Move it all into platforms/pseries.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Registers system call for the powerpc architecture.
Signed-off-by: Janak Desai <janak@us.ibm.com>
Cc: Al Viro <viro@ftp.linux.org.uk>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Michael Kerrisk <mtk-manpages@gmx.net>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Andi Kleen <ak@muc.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch adds a windfarm module, windfarm_pm112, for the dual core G5s
(both 2 and 4 core models), keeping the machine from getting into
vacuum-cleaner mode ;) For proper credits, the patch was initially
written by Paul Mackerras, and slightly reworked by me to add overtemp
handling among others. The patch also removes the sysfs attributes from
windfarm_pm81 and windfarm_pm91 and instead adds code to the windfarm
core to automagically expose attributes for sensor & controls.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
A bunch of asm/bug.h includes are both not needed (since it will get
pulled anyway) and bogus (since they are done too early). Removed.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Prototypes aren't so useful without parameter names, add them to lmb.h based
on the names in lmb.c
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
LMB_ALLOC_ANYWHERE doesn't need to be part of the API, it's only used in
lmb.c - so move it out of the header file.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Currently most callers of lmb_alloc() don't check if it worked or not, if it
ever does weird bad things will probably happen. The few callers who do check
just panic or BUG_ON.
So make lmb_alloc() panic internally, to catch bugs at the source. The few
callers who did check the result no longer need to.
The only caller that did anything interesting with the return result was
careful_allocation(). For it we create __lmb_alloc_base() which _doesn't_ panic
automatically, a little messy, but passable.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
It's possible for prom_init to allocate the flat device tree inside the
kdump crash kernel region. If this happens, when we load the kdump kernel we
overwrite the flattened device tree, which is bad.
We could make prom_init try and avoid allocating inside the crash kernel
region, but then we run into issues if the crash kernel region uses all the
space inside the RMO. The easiest solution is to move the flat device tree
once we're running in the kernel.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
- kexec.h is included from assembly code, thus C code must be properly
protected.
- (embedded) ppc32 systems use machine_kexec_simple whose declaration
vanished during a recent powerpc merge change.
Signed-off-by: Albert Herranz <albert_herranz@yahoo.es>
Cc: <fastboot@osdl.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Make the platform function interrupt functions actually work. Calls
irq_enable() for the first in the list, and irq_disable() for the last.
Added *func to struct irq_client so the the user can pass just that to
pmf_unregister_irq_client().
Signed-off-by: Ben Collins <bcollins@ubuntu.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Implement the TIF_RESTORE_SIGMASK flag in the new arch/powerpc kernel, for
both 32-bit and 64-bit system call paths.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The TIF_RESTORE_SIGMASK flag allows us to have a generic implementation of
sys_rt_sigsuspend() instead of duplicating it for each architecture. This
provides such an implementation and makes arch/powerpc use it.
It also tidies up the ppc32 sys_sigsuspend() to use TIF_RESTORE_SIGMASK.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
sparse can't parse a struct definition in include/asm-powerpc/lppaca.h,
even though gcc can accept it. The form looks like this:
struct __attribute__((whatever)) foo { };
An equivalent that both gcc and sparse can handle is
struct foo { } __attribute__((whatever));
This is the only definition of this type in the tree, and fixing it is
easier than fixing sparse.
Signed-off-by: Bryan O'Sullivan <bos@serpentine.com>
[ Side note: fixing sparse wouldn't be hard, but the "attribute at the
end" version is the canonical one, and the one that makes sense. So
let's just fix the kernel instead. Luc Van Oostenryck already sent
out a sparse patch to the sparse mailing list in case anybody cares.
-- Linus ]
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- This contains the arch specific changes for the following the
kdump generic fixes which were already accepted in the upstream.
. Capturing CPU registers (for the case of 'panic' and invoking
the dump using 'sysrq-trigger') from a function (stack frame) which will
be not be available during the kdump boot. Hence, might result in
invalid stack trace.
. Dynamically allocating per cpu ELF notes section instead of
statically for NR_CPUS.
- Fix the compiler warning in prom_init.c.
Signed-off-by: Haren Myneni <haren@us.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
In 2.6.15-git6 a change was commited in the oprofile support in
the powerpc architecture. It introduced the powerpc_oprofile_type
which contains the define G4. This causes a name clash with the
existing wacom usb tablet driver.
CC [M] drivers/usb/input/wacom.o
drivers/usb/input/wacom.c:98: error: conflicting types for `G4'
include/asm/cputable.h:37: error: previous declaration of `G4'
CC [M] drivers/usb/mon/mon_text.o
make[3]: *** [drivers/usb/input/wacom.o] Error 1
make[2]: *** [drivers/usb/input] Error 2
The elements of an enum declared in global scope are effectivly
global identifiers themselves. As such we need to ensure the names
are unique. This patch updates the later oprofile support to use
unique names.
Signed-off-by: Andy Whitcroft <apw@shadowen.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The glibc folks want to use AT_PLATFORM to select between possible
alternative versions of shared libraries. This commit makes the kernel
supply an AT_PLATFORM string that indicates what class of processor
we are running on. Processors with the same set of user-level
instructions and roughly the same instruction scheduling characteristics
are given the same AT_PLATFORM value; for example, 821, 823 and 860
are all reported as "ppc823", and 7447, 7447A, 7448, 7450, 7451, 7455
are all called "ppc7450".
The intention is that the AT_PLATFORM values match the values that
gcc accepts for the -mcpu= option. For values which are numeric
(e.g. -mcpu=750), "ppc" has been prepended.
This also adds a PPC_FEATURE_BOOKE bit to the AT_HWCAP value and sets
it for the 440 family and the Freescale 85xx family.
Signed-off-by: Paul Mackerras <paulus@samba.org>
eieio is only a store - store ordering. When used to order an unlock
operation loads may leak out of the critical region. This is potentially
buggy, one example is if a user wants to atomically read a couple of
values.
We can solve this with an lwsync which orders everything except store - load.
I removed the (now unused) EIEIO_ON_SMP macros and the c versions
isync_on_smp and eieio_on_smp now we dont use them. I also removed some
old comments that were used to identify inline spinlocks in assembly,
they dont make sense now our locks are out of line.
Another interesting thing was that read_unlock was using an eieio even
though the rest of the spinlock code had already been converted to
use lwsync.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
At present the lppaca - the structure shared with the iSeries
hypervisor and phyp - is contained within the PACA, our own low-level
per-cpu structure. This doesn't have to be so, the patch below
removes it, making a separate array of lppaca structures.
This saves approximately 500*NR_CPUS bytes of image size and kernel
memory, because we don't need aligning gap between the Linux and
hypervisor portions of every PACA. On the other hand it means an
extra level of dereference in many accesses to the lppaca.
The patch also gets rid of several places where we assign the paca
address to a local variable for no particular reason.
Signed-off-by: David Gibson <dwg@au1.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch consolidates the variety of macros used for loading 32 or
64-bit constants in assembler (LOADADDR, LOADBASE, SET_REG_TO_*). The
idea is to make the set of macros consistent across 32 and 64 bit and
to make it more obvious which is the appropriate one to use in a given
situation. The new macros and their semantics are described in the
comments in ppc_asm.h.
In the process, we change several places that were unnecessarily using
immediate loads on ppc64 to use the GOT/TOC. Likewise we cleanup a
couple of places where we were clumsily subtracting PAGE_OFFSET with
asm instructions to use assemble-time arithmetic or the toreal() macro
instead.
Signed-off-by: David Gibson <dwg@au1.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Add an of_find_property function that returns a struct property
given a property name. Then change the get_property function to
use that routine internally.
Signed-off-by: Dave Boutcher <sleddog@us.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Add support for updating and removing device tree
properties. Since we hand out pointers to properties with gay
abandon, we can't just free the property storage. Instead we
move deleted, or the old copy of an updated property, to a
"dead properties" list.
Also note, its not feasable to kref device tree properties.
we call get_property() all over the kernel in a wild variety
of contexts.
One consequence of this change is that we now take a
read_lock(&devtree_lock) when doing get_property().
Signed-off-by: Dave Boutcher <sleddog@us.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
{get,put}_thread_info() were introduced in 2.5.4 and never
had been called by anything in the tree.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
)
From: Ingo Molnar <mingo@elte.hu>
This is the latest version of the scheduler cache-hot-auto-tune patch.
The first problem was that detection time scaled with O(N^2), which is
unacceptable on larger SMP and NUMA systems. To solve this:
- I've added a 'domain distance' function, which is used to cache
measurement results. Each distance is only measured once. This means
that e.g. on NUMA distances of 0, 1 and 2 might be measured, on HT
distances 0 and 1, and on SMP distance 0 is measured. The code walks
the domain tree to determine the distance, so it automatically follows
whatever hierarchy an architecture sets up. This cuts down on the boot
time significantly and removes the O(N^2) limit. The only assumption
is that migration costs can be expressed as a function of domain
distance - this covers the overwhelming majority of existing systems,
and is a good guess even for more assymetric systems.
[ People hacking systems that have assymetries that break this
assumption (e.g. different CPU speeds) should experiment a bit with
the cpu_distance() function. Adding a ->migration_distance factor to
the domain structure would be one possible solution - but lets first
see the problem systems, if they exist at all. Lets not overdesign. ]
Another problem was that only a single cache-size was used for measuring
the cost of migration, and most architectures didnt set that variable
up. Furthermore, a single cache-size does not fit NUMA hierarchies with
L3 caches and does not fit HT setups, where different CPUs will often
have different 'effective cache sizes'. To solve this problem:
- Instead of relying on a single cache-size provided by the platform and
sticking to it, the code now auto-detects the 'effective migration
cost' between two measured CPUs, via iterating through a wide range of
cachesizes. The code searches for the maximum migration cost, which
occurs when the working set of the test-workload falls just below the
'effective cache size'. I.e. real-life optimized search is done for
the maximum migration cost, between two real CPUs.
This, amongst other things, has the positive effect hat if e.g. two
CPUs share a L2/L3 cache, a different (and accurate) migration cost
will be found than between two CPUs on the same system that dont share
any caches.
(The reliable measurement of migration costs is tricky - see the source
for details.)
Furthermore i've added various boot-time options to override/tune
migration behavior.
Firstly, there's a blanket override for autodetection:
migration_cost=1000,2000,3000
will override the depth 0/1/2 values with 1msec/2msec/3msec values.
Secondly, there's a global factor that can be used to increase (or
decrease) the autodetected values:
migration_factor=120
will increase the autodetected values by 20%. This option is useful to
tune things in a workload-dependent way - e.g. if a workload is
cache-insensitive then CPU utilization can be maximized by specifying
migration_factor=0.
I've tested the autodetection code quite extensively on x86, on 3
P3/Xeon/2MB, and the autodetected values look pretty good:
Dual Celeron (128K L2 cache):
---------------------
migration cost matrix (max_cache_size: 131072, cpu: 467 MHz):
---------------------
[00] [01]
[00]: - 1.7(1)
[01]: 1.7(1) -
---------------------
cacheflush times [2]: 0.0 (0) 1.7 (1784008)
---------------------
Here the slow memory subsystem dominates system performance, and even
though caches are small, the migration cost is 1.7 msecs.
Dual HT P4 (512K L2 cache):
---------------------
migration cost matrix (max_cache_size: 524288, cpu: 2379 MHz):
---------------------
[00] [01] [02] [03]
[00]: - 0.4(1) 0.0(0) 0.4(1)
[01]: 0.4(1) - 0.4(1) 0.0(0)
[02]: 0.0(0) 0.4(1) - 0.4(1)
[03]: 0.4(1) 0.0(0) 0.4(1) -
---------------------
cacheflush times [2]: 0.0 (33900) 0.4 (448514)
---------------------
Here it can be seen that there is no migration cost between two HT
siblings (CPU#0/2 and CPU#1/3 are separate physical CPUs). A fast memory
system makes inter-physical-CPU migration pretty cheap: 0.4 msecs.
8-way P3/Xeon [2MB L2 cache]:
---------------------
migration cost matrix (max_cache_size: 2097152, cpu: 700 MHz):
---------------------
[00] [01] [02] [03] [04] [05] [06] [07]
[00]: - 19.2(1) 19.2(1) 19.2(1) 19.2(1) 19.2(1) 19.2(1) 19.2(1)
[01]: 19.2(1) - 19.2(1) 19.2(1) 19.2(1) 19.2(1) 19.2(1) 19.2(1)
[02]: 19.2(1) 19.2(1) - 19.2(1) 19.2(1) 19.2(1) 19.2(1) 19.2(1)
[03]: 19.2(1) 19.2(1) 19.2(1) - 19.2(1) 19.2(1) 19.2(1) 19.2(1)
[04]: 19.2(1) 19.2(1) 19.2(1) 19.2(1) - 19.2(1) 19.2(1) 19.2(1)
[05]: 19.2(1) 19.2(1) 19.2(1) 19.2(1) 19.2(1) - 19.2(1) 19.2(1)
[06]: 19.2(1) 19.2(1) 19.2(1) 19.2(1) 19.2(1) 19.2(1) - 19.2(1)
[07]: 19.2(1) 19.2(1) 19.2(1) 19.2(1) 19.2(1) 19.2(1) 19.2(1) -
---------------------
cacheflush times [2]: 0.0 (0) 19.2 (19281756)
---------------------
This one has huge caches and a relatively slow memory subsystem - so the
migration cost is 19 msecs.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Ashok Raj <ashok.raj@intel.com>
Signed-off-by: Ken Chen <kenneth.w.chen@intel.com>
Cc: <wilder@us.ibm.com>
Signed-off-by: John Hawkes <hawkes@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add per-arch sched_cacheflush() which is a write-back cacheflush used by
the migration-cost calibration code at bootup time.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Cc: Nick Piggin <nickpiggin@yahoo.com.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
pcibios_claim_one_bus is not needed on iSeries and phbs_remap_io can be
mode static.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
There was a function declared for CONFIG_PSERIES which no longer exists
and the two function declarations for CONFIG_ISERIES have been moved
into an include file in platforms/iseries since they are defined and
used only there.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This reverts part of "ppc64 iSeries: allow build with no PCI"
(145d01e428) which affected generic code
and applies a fix in the arch specific code.
Commit "partly merge iseries do_IRQ"
(5fee9b3b39eb55c7e3619a3b36ceeabffeb8f144) introduced iSeries_get_irq
which was only available if CONFIG_PCI is set.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Mainly just removing file names from the comments.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Also does some comment cleanups and removal of unnecessary
variables.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Heikki Lindholm pointed out that there was a potential race with the
lazy CPU state (FP, VR, EVR) stuff if preempt is enabled. The race
is that in the process of restoring FP state on sigreturn, the task
gets preempted by a user task that wants to use the FPU. It will take
an FP unavailable exception, which will write the current FPU state
to the thread_struct, overwriting the values which sigreturn has
stored. Note that this can only happen on UP since we don't implement
lazy CPU state on SMP.
The fix is to flush the lazy CPU state before updating the
thread_struct. To do this we re-use the flush_lazy_cpu_state()
function from process.c.
Signed-off-by: Paul Mackerras <paulus@samba.org>
PPC32 is still using asm-generic/4level-fixup.h, but asm-powerpc/page.h
was defining pud_t and pgd_t. Depending on the order in which files
got included, this could result in a compilation error. Tweak the ifdef
so that page.h doesn't try to define pud_t on ppc32 (which uses 2-level
page tables).
Signed-off-by: Paul Mackerras <paulus@samba.org>
The current ppc64 per cpu data implementation is quite slow. eg:
lhz 11,18(13) /* smp_processor_id() */
ld 9,.LC63-.LCTOC1(30) /* per_cpu__variable_name */
ld 8,.LC61-.LCTOC1(30) /* __per_cpu_offset */
sldi 11,11,3 /* form index into __per_cpu_offset */
mr 10,9
ldx 9,11,8 /* __per_cpu_offset[smp_processor_id()] */
ldx 0,10,9 /* load per cpu data */
5 loads for something that is supposed to be fast, pretty awful. One
reason for the large number of loads is that we have to synthesize 2
64bit constants (per_cpu__variable_name and __per_cpu_offset).
By putting __per_cpu_offset into the paca we can avoid the 2 loads
associated with it:
ld 11,56(13) /* paca->data_offset */
ld 9,.LC59-.LCTOC1(30) /* per_cpu__variable_name */
ldx 0,9,11 /* load per cpu data
Longer term we can should be able to do even better than 3 loads.
If per_cpu__variable_name wasnt a 64bit constant and paca->data_offset
was in a register we could cut it down to one load. A suggestion from
Rusty is to use gcc's __thread extension here. In order to do this we
would need to free up r13 (the __thread register and where the paca
currently is). So far Ive had a few unsuccessful attempts at doing that :)
The patch also allocates per cpu memory node local on NUMA machines.
This patch from Rusty has been sitting in my queue _forever_ but stalled
when I hit the compiler bug. Sorry about that.
Finally I also only allocate per cpu data for possible cpus, which comes
straight out of the x86-64 port. On a pseries kernel (with NR_CPUS == 128)
and 4 possible cpus we see some nice gains:
total used free shared buffers cached
Mem: 4012228 212860 3799368 0 0 162424
total used free shared buffers cached
Mem: 4016200 212984 3803216 0 0 162424
A saving of 3.75MB. Quite nice for smaller machines. Note: we now have
to be careful of per cpu users that touch data for !possible cpus.
At this stage it might be worth making the NUMA and possible cpu
optimisations generic, but per cpu init is done so early we have to be
careful that all architectures have their possible map setup correctly.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This stops parport from accessing nonexistent parallel ports.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch adds Kconfig entries to control the early debugging options,
currently in setup_64.c.
Doing this via Kconfig rather than #defines means you can have one source tree,
which is buildable for multiple platforms - and you can enable the correct
early debug option for each platform via .config.
I made udbg_early_init() a static inline because otherwise GCC is to daft to
optimise it away when debugging is off.
Now that we have udbg_init_rtas() we can make call_rtas_display_status* static.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The following patch (against 2.6.15-rc5-mm3) fixes a kprobes build break
due to changes introduced in the kprobe locking in 2.6.15-rc5-mm3. In
addition, the patch reverts back the open-coding of kprobe_mutex.
Signed-off-by: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Acked-by: Anil S Keshavamurthy <anil.s.keshavamurthy@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Currently arch_remove_kprobes() is only implemented/required for x86_64 and
powerpc. All other architecture like IA64, i386 and sparc64 implementes a
dummy function which is being called from arch independent kprobes.c file.
This patch removes the dummy functions and replaces it with
#define arch_remove_kprobe(p, s) do { } while(0)
Signed-off-by: Anil S Keshavamurthy <anil.s.keshavamurthy@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The arch specific kprobes.h files never gets included when CONFIG_KPROBES is
turned off. Hence check for CONFIG_KPROBES is not appropriate here in this
arch specific kprobes.h files.
Also the below defined function kprobes_exception_notify() is not needed when
CONFIG_KPROBES is off.
Compile tested for both CONFIG_KPROBES=y and N.
Signed-off-by: Anil S Keshavamurthy <anil.s.keshavamurthy@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Kernel/kprobes.c defines get_insn_slot() and free_insn_slot() which are
currently required _only_ for x86_64 and powerpc (which has no-exec support).
FYI, get{free}_insn_slot() functions manages the memory page which is mapped
as executable, required for instruction emulation.
This patch moves those two functions under __ARCH_WANT_KPROBES_INSN_SLOT and
defines __ARCH_WANT_KPROBES_INSN_SLOT in arch specific kprobes.h file.
Signed-off-by: Anil S Keshavamurthy <anil.s.keshavamurthy@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
)
From: Vivek Goyal <vgoyal@in.ibm.com>
crash_setup_regs() is an architecture dependent function which is called in
architecture independent section. So every architecture supporting kexec
should at least provide a dummy definition of crash_setup_regs() even if
crash dumping is not implemented yet, to avoid build failures.
Signed-off-by: Vivek Goyal <vgoyal@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- In case of system crash, current state of cpu registers is saved in memory
in elf note format. So far memory for storing elf notes was being allocated
statically for NR_CPUS.
- This patch introduces dynamic allocation of memory for storing elf notes.
It uses alloc_percpu() interface. This should lead to better memory usage.
- Introduced based on Andi Kleen's and Eric W. Biederman's suggestions.
- This patch also moves memory allocation for elf notes from architecture
dependent portion to architecture independent portion. Now crash_notes is
architecture independent. The whole idea is that size of memory to be
allocated per cpu (MAX_NOTE_BYTES) can be architecture dependent and
allocation of this memory can be architecture independent.
Signed-off-by: Vivek Goyal <vgoyal@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The previous change by Kumar Gala in this area led to legacy_serial.c
and udbg_16550.c being built as modules when CONFIG_SERIAL_8250=m.
Fix this by introducing a new symbol, CONFIG_PPC_UDBG_16550, to
control whether these files get built, and arrange for it to be selected
for those platforms that need it.
Signed-off-by: Paul Mackerras <paulus@samba.org>
241-eeh-save-bars-earlier.patch
Save the PCI device bars *before* any PCI probing is done.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
(cherry picked from 76c902b919098860f3d4e125f847abcc4cb1782a commit)
238-eeh-stop-if-reset_failed.patch
If the firmware is unable to reset the PCI slot for some reason, then
don't attempt any further recovery steps after that point. Instead,
mark the device as permanently failed.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
(cherry picked from e06b942521eb2cdaf232726f45a820d5837acb12 commit)
234-eeh-find-pe.patch
The find_device_pe() routine is duplicated in two files. Remove one of
the two copies, declare the other extern.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
(cherry picked from 48408e708282d4d0269136ff27ea5acbd9410b5a commit)
26-eeh-partition-endpoint.patch
New versions of firmware introduce a new method by which the
"partitionable endpoint" (the point at which the pci bus is cut)
should be located. This code adds the support for this (mandatory)
new feature.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
(cherry picked from 9fcfb5d35b5294659f9299aa9cae6fd16325c07e commit)
25-pci-address-cache.patch
The core EEH file is rather large. This patch splits out a self-contained
chunk of it into its own file. This is the chunk that performes the
caching and lookup of pci devices based on the i/o addresses of thier
resoures. This code is almos architecture-independent and could be
used by any system that wanted to find a pci device based only on
the i/o address used by the device.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
(cherry picked from b0b291d59906d4a9a89ed9e34d9fd684c7188924 commit)
Various PCI bus errors can be signaled by newer PCI controllers. The
core error recovery routines are architecture dependent. This patch adds
a recovery infrastructure for the PPC64 pSeries systems.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
(cherry picked from e8ca11b460c4c9c7fa6b529be221529ebd770e38 commit)
add the per-arch mutex.h files for the remaining architectures.
We default to asm-generic/mutex-dec.h, because that performs
quite well on most arches. Arches that do not have atomic
decrement/increment instructions should switch to mutex-xchg.h
instead. Arches can also provide their own implementation for
the mutex fastpath primitives.
Signed-off-by: Arjan van de Ven <arjan@infradead.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
add atomic_xchg() to all the architectures. Needed by the new mutex code.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Arjan van de Ven <arjan@infradead.org>
My recent changes to oprofile broke it when built as a module. Fix it by
using an enum instead of a function pointer. This way we still retain
the oprofile configuration in the cputable.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This is the platform function interpreter itself along with the backends
for UniN/U3/U4, mac-io, GPIOs and i2c. It adds the ability to execute
those do-platform-* scripts in the device-tree (at least for most
devices for which a backend is provided). This should replace the clock
spreading hacks properly. It might also have an impact on all sort of
machines since some of the scripts marked "at init" will now be executed
on boot (or some other on sleep/wakeup), those will possibly do things
that the kernel didn't do at all, like setting some values into some i2c
devices (changing thermal sensor calibration or conversion rate) etc...
Thus regression testing is MUCH welcome. Also loook for errors in dmesg.
That's also why I've left rather verbose debugging enabled in this
version of the patch.
(I do expect some Windtunnel G4s to show some errors as they have an i2c
clock chip on the PMU bus that uses some primitives that the i2c backend
doesn't implement yet. I really need users that have one of those
machine to come back to me so we can get that done right, though the
errors themselves should be harmless, I suspect the machine might not
run at full speed).
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This is the continuation of the previous patch. This one removes the old
PowerMac i2c drivers (i2c-keywest and i2c-pmac-smu) and replaces them
both with a single stub driver that uses the new PowerMac low i2c layer.
Now that i2c-keywest is gone, the low-i2c code is extended to support
interrupt driver transfers. All i2c busses now appear as platform
devices. Compatibility with existing drivers should be maintained as the
i2c bus names have been kept identical, except for the SMU bus but in
that later case, all users has been fixed.
With that patch added, matching a device node to an i2c_adapter becomes
trivial.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This is the first part of a rework of the PowerMac i2c code. It
completely reworks the "low_i2c" layer. It is now more flexible,
supports KeyWest, SMU and PMU i2c busses, and provides functions to
match device nodes to i2c busses and adapters.
This patch also extends & fix some bugs in the SMU driver related to i2c
support and removes the clock spreading hacks from the pmac feature code
rather than adapting them to the new API since they'll be replaced by
the platform function code completely in patch 3/5
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
For far, all SPU triggered interrupts always end up on
the first SMT thread, which is a bad solution.
This patch implements setting the affinity to the
CPU that was running last when entering execution on
an SPU. This should result in a significant reduction
in IPI calls and better cache locality for SPE thread
specific data.
Signed-off-by: Arnd Bergmann <arndb@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The size of the local store is architecture defined
and independent from the page size, so it should
not be defined in terms of pages in the first place.
This mistake broke a few places when building for
64kb pages.
Signed-off-by: Arnd Bergmann <arndb@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
In a hypervisor based setup, direct access to the first
priviledged register space can typically not be allowed
to the kernel and has to be implemented through hypervisor
calls.
As suggested by Masato Noguchi, let's abstract the register
access trough a number of function calls. Since there is
currently no public specification of actual hypervisor
calls to implement this, I only provide a place that
makes it easier to hook into.
Cc: Masato Noguchi <Masato.Noguchi@jp.sony.com>
Cc: Geoff Levand <geoff.levand@am.sony.com>
Signed-off-by: Arnd Bergmann <arndb@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
checking bits manually might not be synchonized with
the use of set_bit/clear_bit. Make sure we always use
the correct bitops by removing the unnecessary
identifiers.
Signed-off-by: Arnd Bergmann <arndb@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch enables support for pause(0) power management state
for the Cell Broadband Processor, which is import for power efficient
operation. The pervasive infrastructure will in the future enable
us to introduce more functionality specific to the Cell's
pervasive unit.
From: Maximino Aguilar <maguilar@us.ibm.com>
Signed-off-by: Arnd Bergmann <arndb@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Undefined symbols (eeh_add_device_tree_early and eeh_remove_bus_device)
when EEH is not enabled. This small patch will fix this.
Acked-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Added a common udbg_progress for use by ppc_md.progress()
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Kill L1_CACHE_SHIFT from all arches. Since L1_CACHE_SHIFT_MAX is not used
anymore with the introduction of INTERNODE_CACHE, kill L1_CACHE_SHIFT_MAX.
Signed-off-by: Ravikiran Thirumalai <kiran@scalex86.org>
Signed-off-by: Shai Fultheim <shai@scalex86.org>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
include/asm-ppc/ had #ifdef __KERNEL__ in all header files that
are not meant for use by user space, include/asm-powerpc does
not have this yet.
This patch gets us a lot closer there. There are a few cases
where I was not sure, so I left them out. I have verified
that no CONFIG_* symbols are used outside of __KERNEL__
any more and that there are no obvious compile errors when
including any of the headers in user space libraries.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch adds oprofile support for the 7450 and all its multitudinous
derivatives.
* Added 7450 (and derivatives) support for oprofile
* Changed e500 cputable to have oprofile model and cpu_type fields
* Added support for classic 32-bit performance monitor interrupt
* Cleaned up common powerpc oprofile code to be as common as possible
* Cleaned up oprofile_impl.h to reflect 32 bit classic code
* Added 32-bit MMCRx bitfield definitions and SPR numbers
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This fixes pci_address_to_pio() to return an unsigned long (to be safe)
and fixes a bug in the implementation that caused it to return a bogus
IO port number
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
On ppc64, we independently define VMALLOCBASE and VMALLOC_START to be
the same thing: the start of the vmalloc() area at 0xd000000000000000.
VMALLOC_START is used much more widely, including in generic code, so
this patch gets rid of the extraneous VMALLOCBASE.
This does require moving the definitions of region IDs from page_64.h
to pgtable.h, but they don't clearly belong in the former rather than
the latter, anyway. While we're moving them, clean up the definitions
of the REGION_IDs:
- Abolish REGION_SIZE, it was only used once, to define
REGION_MASK anyway
- Define the specific region ids in terms of the REGION_ID()
macro.
- Define KERNEL_REGION_ID in terms of PAGE_OFFSET rather than
KERNELBASE. It amounts to the same thing, but conceptually this is
about the region of the linear mapping (which starts at PAGE_OFFSET)
rather than of the kernel text itself (which is at KERNELBASE).
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This adds some very basic support for the new machines, including the
Quad G5 (tested), and other new dual core based machines and iMac G5
iSight (untested). This is still experimental ! There is no thermal
control yet, there is no proper handing of MSIs, etc.. but it
boots, I have all 4 cores up on my machine. Compared to the previous
version of this patch, this one adds DART IOMMU support for the U4
chipset and thus should work fine on setups with more than 2Gb of RAM.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
There is code in the RPAPHP directory that is identical to this routine;
I'll be removing that code in an upcoming patch, but this patch is needed
to expose the function to make it callable.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Cleanup the MPIC IO-APIC workarounds, make them a bit more generic,
smaller and faster.
Signed-off-by: Segher Boessenkool <segher@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The pre-parsed addrs/n_addrs fields in struct device_node are finally
gone. Remove the dodgy heuristics that did that parsing at boot and
remove the fields themselves since we now have a good replacement with
the new OF parsing code. This patch also fixes a bunch of drivers to use
the new code instead, so that at least pmac32, pseries, iseries and g5
defconfigs build.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
