When the driver probe fails, all the resources that were allocated prior
to the failure must be freed. However, hwrm dma response memory is not
getting freed.
This patch fixes the problem described above.
Fixes: c0c050c58d ("bnxt_en: New Broadcom ethernet driver.")
Signed-off-by: Venkat Duvvuru <venkatkumar.duvvuru@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In HWRM_QUEUE_COS2BW_CFG request, enables field should have the bits
set only for the queue ids which are having the valid parameters.
This causes firmware to return error when the TC to hardware CoS queue
mapping is not 1:1 during DCBNL ETS setup.
Fixes: 2e8ef77ee0 ("bnxt_en: Add TC to hardware QoS queue mapping logic.")
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The enables bit for VNIC was set wrong when calling the HWRM_FUNC_CFG
firmware call to reserve VNICs. This has the effect that the firmware
will keep a large number of VNICs for the PF, and having very few for
VFs. DPDK driver running on the VFs, which requires more VNICs, may not
work properly as a result.
Fixes: 674f50a5b0 ("bnxt_en: Implement new method to reserve rings.")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The AON_PM_L2 is normally used to trigger and identify the source of a
wake-up event. Since the RX_SYS clock is no longer turned off, we also
have an interrupt being sent to the SYSTEMPORT INTRL_2_0 controller, and
that interrupt remains active up until the magic packet detector is
disabled which happens much later during the driver resumption.
The race happens if we have a CPU that is entering the SYSTEMPORT
INTRL2_0 handler during resume, and another CPU has managed to clear the
wake-up interrupt during bcm_sysport_resume_from_wol(). In that case, we
have the first CPU stuck in the interrupt handler with an interrupt
cause that has been cleared under its feet, and so we keep returning
IRQ_NONE and we never make any progress.
This was not a problem before because we would always turn off the
RX_SYS clock during WoL, so the SYSTEMPORT INTRL2_0 would also be turned
off as well, thus not latching the interrupt.
The fix is to make sure we do not enable either the MPD or
BRCM_TAG_MATCH interrupts since those are redundant with what the
AON_PM_L2 interrupt controller already processes and they would cause
such a race to occur.
Fixes: bb9051a2b2 ("net: systemport: Add support for WAKE_FILTER")
Fixes: 83e82f4c70 ("net: systemport: add Wake-on-LAN support")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current netpoll implementation in the bnxt_en driver has problems
that may miss TX completion events. bnxt_poll_work() in effect is
only handling at most 1 TX packet before exiting. In addition,
there may be in flight TX completions that ->poll() may miss even
after we fix bnxt_poll_work() to handle all visible TX completions.
netpoll may not call ->poll() again and HW may not generate IRQ
because the driver does not ARM the IRQ when the budget (0 for netpoll)
is reached.
We fix it by handling all TX completions and to always ARM the IRQ
when we exit ->poll() with 0 budget.
Also, the logic to ACK the completion ring in case it is almost filled
with TX completions need to be adjusted to take care of the 0 budget
case, as discussed with Eric Dumazet <edumazet@google.com>
Reported-by: Song Liu <songliubraving@fb.com>
Reviewed-by: Song Liu <songliubraving@fb.com>
Tested-by: Song Liu <songliubraving@fb.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As diagnosed by Song Liu, ndo_poll_controller() can
be very dangerous on loaded hosts, since the cpu
calling ndo_poll_controller() might steal all NAPI
contexts (for all RX/TX queues of the NIC). This capture
can last for unlimited amount of time, since one
cpu is generally not able to drain all the queues under load.
bnxt uses NAPI for TX completions, so we better let core
networking stack call the napi->poll() to avoid the capture.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As diagnosed by Song Liu, ndo_poll_controller() can
be very dangerous on loaded hosts, since the cpu
calling ndo_poll_controller() might steal all NAPI
contexts (for all RX/TX queues of the NIC). This capture
can last for unlimited amount of time, since one
cpu is generally not able to drain all the queues under load.
bnx2x uses NAPI for TX completions, so we better let core
networking stack call the napi->poll() to avoid the capture.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
bnxt offload code currently supports only 'push' and 'pop' operation: let
.ndo_setup_tc() return -EOPNOTSUPP if VLAN 'modify' action is configured.
Fixes: 2ae7408fed ("bnxt_en: bnxt: add TC flower filter offload support")
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Acked-by: Sathya Perla <sathya.perla@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the following compile warning:
drivers/net/ethernet/broadcom/bnxt/bnxt_devlink.c:49:5: warning: nvm_param.dir_type may be used uninitialized in this function [-Wmaybe-uninitialized]
if (nvm_param.dir_type == BNXT_NVM_PORT_CFG)
Signed-off-by: zhong jiang <zhongjiang@huawei.com>
Acked-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The recent commit to always forward the VF MAC address to the PF for
approval may not work if the PF driver or the firmware is older. This
will cause the VF driver to fail during probe:
bnxt_en 0000:00:03.0 (unnamed net_device) (uninitialized): hwrm req_type 0xf seq id 0x5 error 0xffff
bnxt_en 0000:00:03.0 (unnamed net_device) (uninitialized): VF MAC address 00:00:17:02:05:d0 not approved by the PF
bnxt_en 0000:00:03.0: Unable to initialize mac address.
bnxt_en: probe of 0000:00:03.0 failed with error -99
We fix it by treating the error as fatal only if the VF MAC address is
locally generated by the VF.
Fixes: 707e7e9660 ("bnxt_en: Always forward VF MAC address to the PF.")
Reported-by: Seth Forshee <seth.forshee@canonical.com>
Reported-by: Siwei Liu <loseweigh@gmail.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, the driver adjusts the bp->hw_resc.max_cp_rings by the number
of MSIX vectors used by RDMA. There is one code path in open that needs
to check the true max_cp_rings including any used by RDMA. This code
is now checking for the reduced max_cp_rings which will fail when the
number of cp rings is very small.
To fix this in a clean way, we don't adjust max_cp_rings anymore.
Instead, we add a helper bnxt_get_max_func_cp_rings_for_en() to get the
reduced max_cp_rings when appropriate.
Fixes: ec86f14ea5 ("bnxt_en: Add ULP calls to stop and restart IRQs.")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove unused bnxt_subtract_ulp_resources(). Change
bnxt_get_max_func_irqs() to static since it is only locally used.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the driver detects that resources have changed during open, it
should reset the rx and tx rings to 0. This will properly setup the
init sequence to initialize the default rings again. We also need
to signal the RDMA driver to stop and clear its interrupts. We then
call the RoCE driver to restart if a new set of default rings is
successfully reserved.
Fixes: 25e1acd6b9 ("bnxt_en: Notify firmware about IF state changes.")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When using the fixed PHY with GENET (e.g. MOCA) the PHY link
status can be determined from the internal link status captured
by the MAC. This allows the PHY state machine to use the correct
link state with the fixed PHY even if MAC link event interrupts
are missed when the net device is opened.
Fixes: 8d88c6ebb3 ("net: bcmgenet: enable MoCA link state change detection")
Signed-off-by: Doug Berger <opendmb@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After commit 90b73b77d0, list_head is no longer needed.
Now we just need to convert the list iteration to array
iteration for drivers.
Fixes: 90b73b77d0 ("net: sched: change action API to use array of pointers to actions")
Cc: Jiri Pirko <jiri@mellanox.com>
Cc: Vlad Buslov <vladbu@mellanox.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The bnxt_coredump_record structure is very long, causing a warning
about possible stack overflow on 32-bit architectures:
drivers/net/ethernet/broadcom/bnxt/bnxt_ethtool.c: In function 'bnxt_get_coredump':
drivers/net/ethernet/broadcom/bnxt/bnxt_ethtool.c:2989:1: error: the frame size of 1188 bytes is larger than 1024 bytes [-Werror=frame-larger-than=]
I could not see any reason to operate on an on-stack copy of the
structure before copying it back into the caller-provided buffer, which
also simplifies the code here.
Fixes: 6c5657d085 ("bnxt_en: Add support for ethtool get dump.")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The only remaining caller of this function is inside of an #ifdef
after another caller got removed. This causes a harmless warning
in some configurations:
drivers/net/ethernet/broadcom/bcmsysport.c:1068:13: error: 'bcm_sysport_resume_from_wol' defined but not used [-Werror=unused-function]
Removing the #ifdef around the PM functions simplifies the code
and avoids the problem but letting the compiler drop the unused
functions silently.
Fixes: 9e85e22713 ("net: systemport: Do not re-configure upon WoL interrupt")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The utsname()->nodename string may be 64 bytes long, and it gets
copied without the trailing nul byte into the shorter record->system_name,
as gcc now warns:
In file included from include/linux/bitmap.h:9,
from include/linux/ethtool.h:16,
from drivers/net/ethernet/broadcom/bnxt/bnxt_ethtool.c:13:
In function 'strncpy',
inlined from 'bnxt_fill_coredump_record' at drivers/net/ethernet/broadcom/bnxt/bnxt_ethtool.c:2863:2:
include/linux/string.h:254:9: error: '__builtin_strncpy' output truncated before terminating nul copying as many bytes from a string as its length [-Werror=stringop-truncation]
Using strlcpy() at least avoids overflowing the destination buffer
and adds proper nul-termination. It may still truncate long names
though, which probably can't be solved here.
Fixes: 6c5657d085 ("bnxt_en: Add support for ethtool get dump.")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes following smatch warnings:
drivers/net/ethernet/broadcom/bnxt/bnxt_ethtool.c:2826 bnxt_fill_coredump_seg_hdr() error: strcpy() '"sEgM"' too large for 'seg_hdr->signature' (5 vs 4)
drivers/net/ethernet/broadcom/bnxt/bnxt_ethtool.c:2858 bnxt_fill_coredump_record() error: strcpy() '"cOrE"' too large for 'record->signature' (5 vs 4)
drivers/net/ethernet/broadcom/bnxt/bnxt_ethtool.c:2879 bnxt_fill_coredump_record() error: strcpy() 'utsname()->sysname' too large for 'record->os_name' (65 vs 32)
Fixes: 6c5657d085 ("bnxt_en: Add support for ethtool get dump.")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Addresses-Coverity-ID: 114878 ("Missing break in switch")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The SYSTEMPORT MAC allows up to 8 filters to be programmed to wake-up
from LAN. Verify that we have up to 8 filters and program them to the
appropriate RXCHK entries to be matched (along with their masks).
We need to update the entry and exit to Wake-on-LAN mode to keep the
RXCHK engine running to match during suspend, but this is otherwise
fairly similar to Magic Packet detection.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The CNP CoS queue is reserved for internal RDMA Congestion Notification
Packets (CNP) and should not be used for a TC. Modify the CoS queue
discovery code to skip over the CNP CoS queue and to reduce
bp->max_tc accordingly. However, if RDMA is disabled in NVRAM, the
the CNP CoS queue can be used for a TC.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Expand the .ieee_setapp() and ieee_delapp() DCBNL methods to support
DSCP. This allows DSCP values to user priority mappings instead
of using VLAN priorities. Each DSCP mapping is added or deleted one
entry at a time using the firmware API. The firmware call can only be
made from a PF.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Export temperature sensor reading via hwmon sysfs.
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use latest firmware API to notify firmware about IF state changes.
Firmware has the option to clean up resources during IF down and
to require the driver to reserve resources again during IF up.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The flags field is almost getting full. Move firmware capability flags
to a new fw_cap field to better organize these firmware flags.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The BNXT_FLAG_NEW_RM flag is checked a lot in the code to determine if
the new resource manager is in effect. Define a macro to perform
this check.
Signed-off-by: Michael Chan <michael.chan@broadocm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support to collect live firmware coredump via ethtool.
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set the default hash mode flag in HWRM_VNIC_RSS_CFG to signal to the
firmware that the driver is compliant with the latest spec. With
that, the firmware can return expanded RSS profile IDs that the driver
checks to setup the proper gso_type for GRO-HW packets. But instead
of checking for the new profile IDs, we check the IP_TYPE flag
in TPA_START which is more straight forward than checking a list of
profile IDs.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The new mode is "minimal-static" to be used when resources are more
limited to support a large number of VFs, for example The PF driver
will provision guaranteed minimum resources of 0. Each VF has no
guranteed resources until it tries to reserve resources during device
open.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During hotplug, the driver's open function can be called almost
immediately after power on reset. The PHY may not be ready and the
firmware may return failure when the driver tries to update PHY
settings. Add retry logic fired from the driver's timer to retry
the operation for 5 seconds.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add code to detect firmware support for external loopback and the extra
test entry for external loopback.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver gathers statistics using 2 mechanisms. Some stats are DMA'ed
directly from hardware and others are polled from the driver's timer.
Currently, we only adjust the DMA frequency based on the ethtool
stats-block-usecs setting. This patch adjusts the driver's timer
frequency as well to make everything consistent.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
New interface has firmware core dump support, new extended port
statistics, and IF state change notifications to the firmware.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Create a helper function to turn on/off MPD, this will be used to avoid
duplicating code as we are going to add additional types of wake-up
types.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
We already properly resume from Wake-on-LAN whether such a condition
occured or not, no need to process the WoL interrupt for functional
changes since that could race with other settings.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The else-if branch and else branch set mac_ok to true similarly,
so combine the two into single else branch.
Also add comments to explain the two conditions, which
from Michael Chan and Vasundhara Volam.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Do not define again the polynomial but use header with existing define.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Rx hash/filter table configuration uses rss_conf_obj to configure filters
in the hardware. This object is initialized only when the interface is
brought up.
This patch adds driver changes to configure rss params only when the device
is in opened state. In port disabled case, the config will be cached in the
driver structure which will be applied in the successive load path.
Please consider applying it to 'net' branch.
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Both BCMGENET and SYSTEMPORT build just fine with CONFIG_OF=n, we do have a
dependency on HAS_IOMEM that was not being reflected for SYSTEMPORT so add
that.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch has fix for TX timeout while running bi-directional
traffic with 100 Mbps using 5762.
Signed-off-by: Sanjeev Bansal <sanjeevb.bansal@broadcom.com>
Signed-off-by: Siva Reddy Kallam <siva.kallam@broadcom.com>
Reviewed-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Siva Reddy Kallam <siva.kallam@broadcom.com>
Reviewed-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
hwrm_dbg_resp_addr and hwrm_dbg_resp_dma_addr are never used
and can be removed.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann says:
====================
pull-request: bpf-next 2018-07-15
The following pull-request contains BPF updates for your *net-next* tree.
The main changes are:
1) Various different arm32 JIT improvements in order to optimize code emission
and make the JIT code itself more robust, from Russell.
2) Support simultaneous driver and offloaded XDP in order to allow for advanced
use-cases where some work is offloaded to the NIC and some to the host. Also
add ability for bpftool to load programs and maps beyond just the cgroup case,
from Jakub.
3) Add BPF JIT support in nfp for multiplication as well as division. For the
latter in particular, it uses the reciprocal algorithm to emulate it, from Jiong.
4) Add BTF pretty print functionality to bpftool in plain and JSON output
format, from Okash.
5) Add build and installation to the BPF helper man page into bpftool, from Quentin.
6) Add a TCP BPF callback for listening sockets which is triggered right after
the socket transitions to TCP_LISTEN state, from Andrey.
7) Add a new cgroup tree command to bpftool which iterates over the whole cgroup
tree and prints all attached programs, from Roman.
8) Improve xdp_redirect_cpu sample to support parsing of double VLAN tagged
packets, from Jesper.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
prog_attached of struct netdev_bpf should have been superseded
by simply setting prog_id long time ago, but we kept it around
to allow offloading drivers to communicate attachment mode (drv
vs hw). Subsequently drivers were also allowed to report back
attachment flags (prog_flags), and since nowadays only programs
attached will XDP_FLAGS_HW_MODE can get offloaded, we can tell
the attachment mode from the flags driver reports. Remove
prog_attached member.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
SYSTEMPORT Lite reversed the logic compared to SYSTEMPORT, the
GIB_FCS_STRIP bit is set when the Ethernet FCS is stripped, and that bit
is not set by default. Fix the logic such that we properly check whether
that bit is set or not and we don't forward an extra 4 bytes to the
network stack.
Fixes: 44a4524c54 ("net: systemport: Add support for SYSTEMPORT Lite")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
