- Remove socket skb caches
- Add a SO_RESERVE_MEM socket op to forward allocate buffer space
and avoid memory accounting overhead on each message sent
- Introduce managed neighbor entries - added by control plane and
resolved by the kernel for use in acceleration paths (BPF / XDP
right now, HW offload users will benefit as well)
- Make neighbor eviction on link down controllable by userspace
to work around WiFi networks with bad roaming implementations
- vrf: Rework interaction with netfilter/conntrack
- fq_codel: implement L4S style ce_threshold_ect1 marking
- sch: Eliminate unnecessary RCU waits in mini_qdisc_pair_swap()
BPF:
- Add support for new btf kind BTF_KIND_TAG, arbitrary type tagging
as implemented in LLVM14
- Introduce bpf_get_branch_snapshot() to capture Last Branch Records
- Implement variadic trace_printk helper
- Add a new Bloomfilter map type
- Track <8-byte scalar spill and refill
- Access hw timestamp through BPF's __sk_buff
- Disallow unprivileged BPF by default
- Document BPF licensing
Netfilter:
- Introduce egress hook for looking at raw outgoing packets
- Allow matching on and modifying inner headers / payload data
- Add NFT_META_IFTYPE to match on the interface type either from
ingress or egress
Protocols:
- Multi-Path TCP:
- increase default max additional subflows to 2
- rework forward memory allocation
- add getsockopts: MPTCP_INFO, MPTCP_TCPINFO, MPTCP_SUBFLOW_ADDRS
- MCTP flow support allowing lower layer drivers to configure msg
muxing as needed
- Automatic Multicast Tunneling (AMT) driver based on RFC7450
- HSR support the redbox supervision frames (IEC-62439-3:2018)
- Support for the ip6ip6 encapsulation of IOAM
- Netlink interface for CAN-FD's Transmitter Delay Compensation
- Support SMC-Rv2 eliminating the current same-subnet restriction,
by exploiting the UDP encapsulation feature of RoCE adapters
- TLS: add SM4 GCM/CCM crypto support
- Bluetooth: initial support for link quality and audio/codec
offload
Driver APIs:
- Add a batched interface for RX buffer allocation in AF_XDP
buffer pool
- ethtool: Add ability to control transceiver modules' power mode
- phy: Introduce supported interfaces bitmap to express MAC
capabilities and simplify PHY code
- Drop rtnl_lock from DSA .port_fdb_{add,del} callbacks
New drivers:
- WiFi driver for Realtek 8852AE 802.11ax devices (rtw89)
- Ethernet driver for ASIX AX88796C SPI device (x88796c)
Drivers:
- Broadcom PHYs
- support 72165, 7712 16nm PHYs
- support IDDQ-SR for additional power savings
- PHY support for QCA8081, QCA9561 PHYs
- NXP DPAA2: support for IRQ coalescing
- NXP Ethernet (enetc): support for software TCP segmentation
- Renesas Ethernet (ravb) - support DMAC and EMAC blocks of
Gigabit-capable IP found on RZ/G2L SoC
- Intel 100G Ethernet
- support for eswitch offload of TC/OvS flow API, including
offload of GRE, VxLAN, Geneve tunneling
- support application device queues - ability to assign Rx and Tx
queues to application threads
- PTP and PPS (pulse-per-second) extensions
- Broadcom Ethernet (bnxt)
- devlink health reporting and device reload extensions
- Mellanox Ethernet (mlx5)
- offload macvlan interfaces
- support HW offload of TC rules involving OVS internal ports
- support HW-GRO and header/data split
- support application device queues
- Marvell OcteonTx2:
- add XDP support for PF
- add PTP support for VF
- Qualcomm Ethernet switch (qca8k): support for QCA8328
- Realtek Ethernet DSA switch (rtl8366rb)
- support bridge offload
- support STP, fast aging, disabling address learning
- support for Realtek RTL8365MB-VC, a 4+1 port 10M/100M/1GE switch
- Mellanox Ethernet/IB switch (mlxsw)
- multi-level qdisc hierarchy offload (e.g. RED, prio and shaping)
- offload root TBF qdisc as port shaper
- support multiple routing interface MAC address prefixes
- support for IP-in-IP with IPv6 underlay
- MediaTek WiFi (mt76)
- mt7921 - ASPM, 6GHz, SDIO and testmode support
- mt7915 - LED and TWT support
- Qualcomm WiFi (ath11k)
- include channel rx and tx time in survey dump statistics
- support for 80P80 and 160 MHz bandwidths
- support channel 2 in 6 GHz band
- spectral scan support for QCN9074
- support for rx decapsulation offload (data frames in 802.3
format)
- Qualcomm phone SoC WiFi (wcn36xx)
- enable Idle Mode Power Save (IMPS) to reduce power consumption
during idle
- Bluetooth driver support for MediaTek MT7922 and MT7921
- Enable support for AOSP Bluetooth extension in Qualcomm WCN399x
and Realtek 8822C/8852A
- Microsoft vNIC driver (mana)
- support hibernation and kexec
- Google vNIC driver (gve)
- support for jumbo frames
- implement Rx page reuse
Refactor:
- Make all writes to netdev->dev_addr go thru helpers, so that we
can add this address to the address rbtree and handle the updates
- Various TCP cleanups and optimizations including improvements
to CPU cache use
- Simplify the gnet_stats, Qdisc stats' handling and remove
qdisc->running sequence counter
- Driver changes and API updates to address devlink locking
deficiencies
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
-----BEGIN PGP SIGNATURE-----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=srde
-----END PGP SIGNATURE-----
Merge tag 'net-next-for-5.16' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next
Pull networking updates from Jakub Kicinski:
"Core:
- Remove socket skb caches
- Add a SO_RESERVE_MEM socket op to forward allocate buffer space and
avoid memory accounting overhead on each message sent
- Introduce managed neighbor entries - added by control plane and
resolved by the kernel for use in acceleration paths (BPF / XDP
right now, HW offload users will benefit as well)
- Make neighbor eviction on link down controllable by userspace to
work around WiFi networks with bad roaming implementations
- vrf: Rework interaction with netfilter/conntrack
- fq_codel: implement L4S style ce_threshold_ect1 marking
- sch: Eliminate unnecessary RCU waits in mini_qdisc_pair_swap()
BPF:
- Add support for new btf kind BTF_KIND_TAG, arbitrary type tagging
as implemented in LLVM14
- Introduce bpf_get_branch_snapshot() to capture Last Branch Records
- Implement variadic trace_printk helper
- Add a new Bloomfilter map type
- Track <8-byte scalar spill and refill
- Access hw timestamp through BPF's __sk_buff
- Disallow unprivileged BPF by default
- Document BPF licensing
Netfilter:
- Introduce egress hook for looking at raw outgoing packets
- Allow matching on and modifying inner headers / payload data
- Add NFT_META_IFTYPE to match on the interface type either from
ingress or egress
Protocols:
- Multi-Path TCP:
- increase default max additional subflows to 2
- rework forward memory allocation
- add getsockopts: MPTCP_INFO, MPTCP_TCPINFO, MPTCP_SUBFLOW_ADDRS
- MCTP flow support allowing lower layer drivers to configure msg
muxing as needed
- Automatic Multicast Tunneling (AMT) driver based on RFC7450
- HSR support the redbox supervision frames (IEC-62439-3:2018)
- Support for the ip6ip6 encapsulation of IOAM
- Netlink interface for CAN-FD's Transmitter Delay Compensation
- Support SMC-Rv2 eliminating the current same-subnet restriction, by
exploiting the UDP encapsulation feature of RoCE adapters
- TLS: add SM4 GCM/CCM crypto support
- Bluetooth: initial support for link quality and audio/codec offload
Driver APIs:
- Add a batched interface for RX buffer allocation in AF_XDP buffer
pool
- ethtool: Add ability to control transceiver modules' power mode
- phy: Introduce supported interfaces bitmap to express MAC
capabilities and simplify PHY code
- Drop rtnl_lock from DSA .port_fdb_{add,del} callbacks
New drivers:
- WiFi driver for Realtek 8852AE 802.11ax devices (rtw89)
- Ethernet driver for ASIX AX88796C SPI device (x88796c)
Drivers:
- Broadcom PHYs
- support 72165, 7712 16nm PHYs
- support IDDQ-SR for additional power savings
- PHY support for QCA8081, QCA9561 PHYs
- NXP DPAA2: support for IRQ coalescing
- NXP Ethernet (enetc): support for software TCP segmentation
- Renesas Ethernet (ravb) - support DMAC and EMAC blocks of
Gigabit-capable IP found on RZ/G2L SoC
- Intel 100G Ethernet
- support for eswitch offload of TC/OvS flow API, including
offload of GRE, VxLAN, Geneve tunneling
- support application device queues - ability to assign Rx and Tx
queues to application threads
- PTP and PPS (pulse-per-second) extensions
- Broadcom Ethernet (bnxt)
- devlink health reporting and device reload extensions
- Mellanox Ethernet (mlx5)
- offload macvlan interfaces
- support HW offload of TC rules involving OVS internal ports
- support HW-GRO and header/data split
- support application device queues
- Marvell OcteonTx2:
- add XDP support for PF
- add PTP support for VF
- Qualcomm Ethernet switch (qca8k): support for QCA8328
- Realtek Ethernet DSA switch (rtl8366rb)
- support bridge offload
- support STP, fast aging, disabling address learning
- support for Realtek RTL8365MB-VC, a 4+1 port 10M/100M/1GE switch
- Mellanox Ethernet/IB switch (mlxsw)
- multi-level qdisc hierarchy offload (e.g. RED, prio and shaping)
- offload root TBF qdisc as port shaper
- support multiple routing interface MAC address prefixes
- support for IP-in-IP with IPv6 underlay
- MediaTek WiFi (mt76)
- mt7921 - ASPM, 6GHz, SDIO and testmode support
- mt7915 - LED and TWT support
- Qualcomm WiFi (ath11k)
- include channel rx and tx time in survey dump statistics
- support for 80P80 and 160 MHz bandwidths
- support channel 2 in 6 GHz band
- spectral scan support for QCN9074
- support for rx decapsulation offload (data frames in 802.3
format)
- Qualcomm phone SoC WiFi (wcn36xx)
- enable Idle Mode Power Save (IMPS) to reduce power consumption
during idle
- Bluetooth driver support for MediaTek MT7922 and MT7921
- Enable support for AOSP Bluetooth extension in Qualcomm WCN399x and
Realtek 8822C/8852A
- Microsoft vNIC driver (mana)
- support hibernation and kexec
- Google vNIC driver (gve)
- support for jumbo frames
- implement Rx page reuse
Refactor:
- Make all writes to netdev->dev_addr go thru helpers, so that we can
add this address to the address rbtree and handle the updates
- Various TCP cleanups and optimizations including improvements to
CPU cache use
- Simplify the gnet_stats, Qdisc stats' handling and remove
qdisc->running sequence counter
- Driver changes and API updates to address devlink locking
deficiencies"
* tag 'net-next-for-5.16' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (2122 commits)
Revert "net: avoid double accounting for pure zerocopy skbs"
selftests: net: add arp_ndisc_evict_nocarrier
net: ndisc: introduce ndisc_evict_nocarrier sysctl parameter
net: arp: introduce arp_evict_nocarrier sysctl parameter
libbpf: Deprecate AF_XDP support
kbuild: Unify options for BTF generation for vmlinux and modules
selftests/bpf: Add a testcase for 64-bit bounds propagation issue.
bpf: Fix propagation of signed bounds from 64-bit min/max into 32-bit.
bpf: Fix propagation of bounds from 64-bit min/max into 32-bit and var_off.
net: vmxnet3: remove multiple false checks in vmxnet3_ethtool.c
net: avoid double accounting for pure zerocopy skbs
tcp: rename sk_wmem_free_skb
netdevsim: fix uninit value in nsim_drv_configure_vfs()
selftests/bpf: Fix also no-alu32 strobemeta selftest
bpf: Add missing map_delete_elem method to bloom filter map
selftests/bpf: Add bloom map success test for userspace calls
bpf: Add alignment padding for "map_extra" + consolidate holes
bpf: Bloom filter map naming fixups
selftests/bpf: Add test cases for struct_ops prog
bpf: Add dummy BPF STRUCT_OPS for test purpose
...
This update has a single change which will use the maximum transfer and
message sizes advertised by SPI controllers to configure limits within
the regmap core, ensuring better interoperation.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAmF/6F8ACgkQJNaLcl1U
h9Calgf+PaI6wr17nU0/m4N50Vjat0bL7iBuEQYPKFWu963M0QasPZEKteJV7sa+
8XVxcBh43E2unQkY+iMfldmBIEfZJwmsaWecdxSair6cWcm8MT6agOOkl6KjiCHM
AQiPI2+UbXDHnPociBmyA+MqI3hWSPZIMirVC+3WAFGLs8wHuRe0G97egkcPh88a
doQ5f2Ei7eCgP4uy+p93S4QWXbsbQVm/yszw0BH0gaqnBylwUfQtU1vdlLyBXW4y
9bB1MnzCdlLbKf4bQd7NcjB2bA8lgAuZ3t5rJoRjZtnf+//fRTB1cu/UkLRFlZme
vsrt60wo52r2v5tiLKA4wrgcvEFR+A==
=8MR4
-----END PGP SIGNATURE-----
Merge tag 'regmap-v5.16' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap
Pull regmap update from Mark Brown:
"A single change to use the maximum transfer and message sizes
advertised by SPI controllers to configure limits within the
regmap core, ensuring better interoperation"
* tag 'regmap-v5.16' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap:
regmap: spi: Set regmap max raw r/w from max_transfer_size
This converts users of mdiobus to mdiodev using the following semantic
patch:
@@
identifier mdiodev;
expression regnum;
@@
- mdiobus_read(mdiodev->bus, mdiodev->addr, regnum)
+ mdiodev_read(mdiodev, regnum)
@@
identifier mdiodev;
expression regnum, val;
@@
- mdiobus_write(mdiodev->bus, mdiodev->addr, regnum, val)
+ mdiodev_write(mdiodev, regnum, val)
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set regmap raw read/write from spi max_transfer_size
so regmap_raw_read/write can split the access into chunks
Signed-off-by: Lucas Tanure <tanureal@opensource.cirrus.com>
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
[André: fix build warning]
Signed-off-by: André Almeida <andrealmeid@collabora.com>
Link: https://lore.kernel.org/r/20211021132721.13669-1-andrealmeid@collabora.com
Signed-off-by: Mark Brown <broonie@kernel.org>
In regcache_rbtree_insert_to_block(), when 'present' realloc failed,
the 'blk' which is supposed to assign to 'rbnode->block' will be freed,
so 'rbnode->block' points a freed memory, in the error handling path of
regcache_rbtree_init(), 'rbnode->block' will be freed again in
regcache_rbtree_exit(), KASAN will report double-free as follows:
BUG: KASAN: double-free or invalid-free in kfree+0xce/0x390
Call Trace:
slab_free_freelist_hook+0x10d/0x240
kfree+0xce/0x390
regcache_rbtree_exit+0x15d/0x1a0
regcache_rbtree_init+0x224/0x2c0
regcache_init+0x88d/0x1310
__regmap_init+0x3151/0x4a80
__devm_regmap_init+0x7d/0x100
madera_spi_probe+0x10f/0x333 [madera_spi]
spi_probe+0x183/0x210
really_probe+0x285/0xc30
To fix this, moving up the assignment of rbnode->block to immediately after
the reallocation has succeeded so that the data structure stays valid even
if the second reallocation fails.
Reported-by: Hulk Robot <hulkci@huawei.com>
Fixes: 3f4ff561bc ("regmap: rbtree: Make cache_present bitmap per node")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20211012023735.1632786-1-yangyingliang@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The ls-extirq irqchip driver accesses regmap inside its implementation
of the struct irq_chip :: irq_set_type method, and currently regmap
only knows to lock using normal spinlocks. But the method above wants
raw spinlock context, so this isn't going to work and triggers a
"[ BUG: Invalid wait context ]" splat.
The best we can do given the arrangement of the code is to patch regmap
and the syscon driver: regmap to support raw spinlocks, and syscon to
request them on behalf of its ls-extirq consumer.
Link: https://lore.kernel.org/lkml/20210825135438.ubcuxm5vctt6ne2q@skbuf/T/#u
Vladimir Oltean (2):
regmap: teach regmap to use raw spinlocks if requested in the config
mfd: syscon: request a regmap with raw spinlocks for some devices
drivers/base/regmap/internal.h | 4 ++++
drivers/base/regmap/regmap.c | 35 +++++++++++++++++++++++++++++-----
drivers/mfd/syscon.c | 16 ++++++++++++++++
include/linux/regmap.h | 2 ++
4 files changed, 52 insertions(+), 5 deletions(-)
--
2.25.1
base-commit: 6efb943b86
Some drivers might access regmap in a context where a raw spinlock is
held. An example is drivers/irqchip/irq-ls-extirq.c, which calls
regmap_update_bits() from struct irq_chip :: irq_set_type, which is a
method called by __irq_set_trigger() under the desc->lock raw spin lock.
Since desc->lock is a raw spin lock and the regmap internal lock for
mmio is a plain spinlock (which can become sleepable on RT), this is an
invalid locking scheme and we get a splat stating that this is a
"[ BUG: Invalid wait context ]".
It seems reasonable for regmap to have an option use a raw spinlock too,
so add that in the config such that drivers can request it.
Suggested-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/20210825205041.927788-2-vladimir.oltean@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The reg_fields array fed to {devm_}regmap_field_bulk_alloc is currently
not const, which is not correct on semantics (the functions shouldn't
change reg_field contents) and prevents pre-defined const reg_field
array to be used.
As the implementation of this function doesn't change the content of it,
just add const to its prototype.
Signed-off-by: Icenowy Zheng <icenowy@sipeed.com>
Link: https://lore.kernel.org/r/20210802063741.76301-1-icenowy@sipeed.com
Signed-off-by: Mark Brown <broonie@kernel.org>
A const qualifier was omitted in the declaration of the regmap_bus
pointer, resulting in the following errors:
drivers/base/regmap/regmap-mdio.c: In function ‘__regmap_init_mdio’:
drivers/base/regmap/regmap-mdio.c:87:7: warning: assignment discards
‘const’ qualifier from pointer target type [-Wdiscarded-qualifiers]
87 | bus = ®map_mdio_c22_bus;
| ^
drivers/base/regmap/regmap-mdio.c:89:7: warning: assignment discards
‘const’ qualifier from pointer target type [-Wdiscarded-qualifiers]
89 | bus = ®map_mdio_c45_bus;
| ^
Fix this by ensuring the pointer has the same qualifiers as the assigned
values.
Fixes: f083be9db0 ("regmap: mdio: Add clause-45 support")
Signed-off-by: Sander Vanheule <sander@svanheule.net>
Link: https://lore.kernel.org/r/f304ca638ffdc66d4803a6df1f75436894bd1d5f.1623244066.git.sander@svanheule.net
Signed-off-by: Mark Brown <broonie@kernel.org>
Modern ethernet phys support the so-called clause-45 register access
mode, which allows for register address widths of 16 bit.
Also allow for 16-bit register address widths, and return a regmap for
clause-45 access in that case.
Signed-off-by: Sander Vanheule <sander@svanheule.net>
Link: https://lore.kernel.org/r/9cc263e3e7d5865edd90453b4183f1cf363cb636.1622743333.git.sander@svanheule.net
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently a regmap configuration for regmap-mdio must have a register
address width of 5 bits (cf. clause-22 register access). This is not
enforced on the provided register addresses, which would enable
clause-45 MDIO bus access, if the right bit packing is used.
Prevent clause-45 access, and other invalid addresses, by masking the
provided register address.
Signed-off-by: Sander Vanheule <sander@svanheule.net>
Link: https://lore.kernel.org/r/f7013f67e6d6ff56ec98660f18320f6ffcc1a777.1622743333.git.sander@svanheule.net
Signed-off-by: Mark Brown <broonie@kernel.org>
Some interrupt controllers have inverted status register:
cleared bits is active interrupts and set bits is inactive interrupts,
so add inverted status support to the framework.
Signed-off-by: Maxim Kochetkov <fido_max@inbox.ru>
Link: https://lore.kernel.org/r/20210525034204.5272-1-fido_max@inbox.ru
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds support for 7 bits register, 17 bits value type register
formating. This is used, for example, by the Analog Devices
ADMV1013/ADMV1014.
Signed-off-by: Antoniu Miclaus <antoniu.miclaus@analog.com>
Signed-off-by: Andrei Drimbarean <andrei.drimbarean@analog.com>
Message-Id: <20210526085223.14896-1-antoniu.miclaus@analog.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
regmap_mdio_read() breaks the principle of "no touch output till it's known
that the operation succeeds". Refactor it accordingly.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20210520120518.30490-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The RTL8231 GPIO and LED expander can be configured for use as an MDIO or SMI
bus device. Currently only the MDIO mode is supported, although SMI mode
support should be fairly straightforward, once an SMI bus driver is available.
Provided features by the RTL8231:
- Up to 37 GPIOs
- Configurable drive strength: 8mA or 4mA (currently unsupported)
- Input debouncing on high GPIOs (currently unsupported)
- Up to 88 LEDs in multiple scan matrix groups
- On, off, or one of six toggling intervals
- "single-color mode": 2×36 single color LEDs + 8 bi-color LEDs
- "bi-color mode": (12 + 2×6) bi-color LEDs + 24 single color LEDs
- Up to one PWM output (currently unsupported)
- Fixed duty cycle, 8 selectable frequencies (1.2kHz - 4.8kHz)
Register access is provided through a new MDIO regmap provider. The GPIO
controller uses gpio-regmap, although a patch is required to support a
limitation of the chip.
There remain some log warnings when probing the device, possibly due to the way
I'm using the MFD subsystem. Would it be possible to avoid these?
[ 2.602242] rtl8231-pinctrl: Failed to locate of_node [id: -2]
[ 2.609380] rtl8231-pinctrl rtl8231-pinctrl.0.auto: no of_node; not parsing pinctrl DT
When no 'leds' sub-node is specified:
[ 2.922262] rtl8231-leds: Failed to locate of_node [id: -2]
[ 2.967149] rtl8231-leds rtl8231-leds.1.auto: no of_node; not parsing pinctrl DT
[ 2.975673] rtl8231-leds rtl8231-leds.1.auto: scan mode missing or invalid
[ 2.983531] rtl8231-leds: probe of rtl8231-leds.1.auto failed with error -22
Changes since v1:
- Reintroduce MDIO regmap, with fixed Kconfig dependencies
- Add configurable dir/value order for gpio-regmap direction_out call
- Drop allocations for regmap fields that are used only on init
- Move some definitions to MFD header
- Add PM ops to replace driver remove for MFD
- Change pinctrl driver to (modified) gpio-regmap
- Change leds driver to use fwnode
Link: https://lore.kernel.org/lkml/cover.1620735871.git.sander@svanheule.net/
Changes since RFC:
- Dropped MDIO regmap interface. I was unable to resolve the Kconfig
dependency issue, so have reverted to using regmap_config.reg_read/write.
- Added pinctrl support
- Added LED support
- Changed root device to MFD, with pinctrl and leds child devices. Root
device is now an mdio_device driver.
Link: https://lore.kernel.org/linux-gpio/cover.1617914861.git.sander@svanheule.net/
Sander Vanheule (7):
regmap: Add MDIO bus support
gpio: regmap: Add configurable dir/value order
dt-bindings: leds: Binding for RTL8231 scan matrix
dt-bindings: mfd: Binding for RTL8231
mfd: Add RTL8231 core device
pinctrl: Add RTL8231 pin control and GPIO support
leds: Add support for RTL8231 LED scan matrix
.../bindings/leds/realtek,rtl8231-leds.yaml | 159 ++++++++
.../bindings/mfd/realtek,rtl8231.yaml | 202 ++++++++++
drivers/base/regmap/Kconfig | 6 +-
drivers/base/regmap/Makefile | 1 +
drivers/base/regmap/regmap-mdio.c | 57 +++
drivers/gpio/gpio-regmap.c | 20 +-
drivers/leds/Kconfig | 10 +
drivers/leds/Makefile | 1 +
drivers/leds/leds-rtl8231.c | 293 ++++++++++++++
drivers/mfd/Kconfig | 9 +
drivers/mfd/Makefile | 1 +
drivers/mfd/rtl8231.c | 153 +++++++
drivers/pinctrl/Kconfig | 11 +
drivers/pinctrl/Makefile | 1 +
drivers/pinctrl/pinctrl-rtl8231.c | 377 ++++++++++++++++++
include/linux/gpio/regmap.h | 3 +
include/linux/mfd/rtl8231.h | 57 +++
include/linux/regmap.h | 36 ++
18 files changed, 1393 insertions(+), 4 deletions(-)
create mode 100644 Documentation/devicetree/bindings/leds/realtek,rtl8231-leds.yaml
create mode 100644 Documentation/devicetree/bindings/mfd/realtek,rtl8231.yaml
create mode 100644 drivers/base/regmap/regmap-mdio.c
create mode 100644 drivers/leds/leds-rtl8231.c
create mode 100644 drivers/mfd/rtl8231.c
create mode 100644 drivers/pinctrl/pinctrl-rtl8231.c
create mode 100644 include/linux/mfd/rtl8231.h
base-commit: 6efb943b86
--
2.31.1
The clean up of struct d can potentiallly index into a null array
d->virt_buf causing errorenous pointer dereferencing issues on
kfree calls. Fix this by adding a null check on d->virt_buf before
attempting to traverse the array to kfree the objects.
Addresses-Coverity: ("Dereference after null check")
Fixes: 4c50144563 ("regmap-irq: Introduce virtual regs to handle more config regs")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Link: https://lore.kernel.org/r/20210406164002.430221-1-colin.king@canonical.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Enable drivers to configure and modify "virtual" registers, which are
non-standard registers that further configure irq type on some devices.
Since they are non-standard, enable drivers to configure them according
to their particular idiosyncrasies by specifying an optional callback
function while registering with the framework.
Signed-off-by: Guru Das Srinagesh <gurus@codeaurora.org>
Link: https://lore.kernel.org/r/07e058cdec2297d15c95c825aa0263064d962d5a.1616613838.git.gurus@codeaurora.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Add "virtual" registers support to handle any irq configuration
registers in addition to the ones the framework currently supports
(status, mask, unmask, wake, type and ack). These are non-standard
registers that further configure irq type on some devices, so enable the
framework to add a variable number of them.
Signed-off-by: Guru Das Srinagesh <gurus@codeaurora.org>
Link: https://lore.kernel.org/r/a1787067004b0e11cb960319082764397469215a.1616613838.git.gurus@codeaurora.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Qualcomm's MFD chips have a top level interrupt status register and
sub-irqs (peripherals). When a bit in the main status register goes
high, it means that the peripheral corresponding to that bit has an
unserviced interrupt. If the bit is not set, this means that the
corresponding peripheral does not.
Commit a2d21848d9 ("regmap: regmap-irq: Add main status register
support") introduced the sub-irq logic that is currently applied only
when reading status registers, but not for any other functions like acking
or masking. Extend the use of sub-irq to all other functions, with two
caveats regarding the specification of offsets:
- Each member of the sub_reg_offsets array should be of length 1
- The specified offsets should be the unequal strides for each sub-irq
device.
In QCOM's case, all the *_base registers are to be configured to the
base addresses of the first sub-irq group, with offsets of each
subsequent group calculated as a difference from these addresses.
Continuing from the example mentioned in the cover letter:
/*
* Address of MISC_INT_MASK = 0x1011
* Address of TEMP_ALARM_INT_MASK = 0x2011
* Address of GPIO01_INT_MASK = 0x3011
*
* Calculate offsets as:
* offset_0 = 0x1011 - 0x1011 = 0 (to access MISC's
* registers)
* offset_1 = 0x2011 - 0x1011 = 0x1000
* offset_2 = 0x3011 - 0x1011 = 0x2000
*/
static unsigned int sub_unit0_offsets[] = {0};
static unsigned int sub_unit1_offsets[] = {0x1000};
static unsigned int sub_unit2_offsets[] = {0x2000};
static struct regmap_irq_sub_irq_map chip_sub_irq_offsets[] = {
REGMAP_IRQ_MAIN_REG_OFFSET(sub_unit0_offsets),
REGMAP_IRQ_MAIN_REG_OFFSET(sub_unit0_offsets),
REGMAP_IRQ_MAIN_REG_OFFSET(sub_unit0_offsets),
};
static struct regmap_irq_chip chip_irq_chip = {
--------8<--------
.not_fixed_stride = true,
.mask_base = MISC_INT_MASK,
.type_base = MISC_INT_TYPE,
.ack_base = MISC_INT_ACK,
.sub_reg_offsets = chip_sub_irq_offsets,
--------8<--------
};
Signed-off-by: Guru Das Srinagesh <gurus@codeaurora.org>
Link: https://lore.kernel.org/r/526562423eaa58b4075362083f561841f1d6956c.1615423027.git.gurus@codeaurora.org
Signed-off-by: Mark Brown <broonie@kernel.org>
There is a upstream commit cffa4b2122f5("regmap:debugfs:
Fix a memory leak when calling regmap_attach_dev") that
adds a if condition when create name for debugfs_name.
With below function invoking logical, debugfs_name is
freed in regmap_debugfs_exit(), but it is not created again
because of the if condition introduced by above commit.
regmap_reinit_cache()
regmap_debugfs_exit()
...
regmap_debugfs_init()
So, set debugfs_name to NULL after it is freed.
Fixes: cffa4b2122 ("regmap: debugfs: Fix a memory leak when calling regmap_attach_dev")
Signed-off-by: Meng Li <Meng.Li@windriver.com>
Link: https://lore.kernel.org/r/20210226021737.7690-1-Meng.Li@windriver.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Here is the large set of char/misc/whatever driver subsystem updates for
5.12-rc1. Over time it seems like this tree is collecting more and more
tiny driver subsystems in one place, making it easier for those
maintainers, which is why this is getting larger.
Included in here are:
- coresight driver updates
- habannalabs driver updates
- virtual acrn driver addition (proper acks from the x86
maintainers)
- broadcom misc driver addition
- speakup driver updates
- soundwire driver updates
- fpga driver updates
- amba driver updates
- mei driver updates
- vfio driver updates
- greybus driver updates
- nvmeem driver updates
- phy driver updates
- mhi driver updates
- interconnect driver udpates
- fsl-mc bus driver updates
- random driver fix
- some small misc driver updates (rtsx, pvpanic, etc.)
All of these have been in linux-next for a while, with the only reported
issue being a merge conflict in include/linux/mod_devicetable.h that you
will hit in your tree due to the dfl_device_id addition from the fpga
subsystem in here. The resolution should be simple.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCYDZf9w8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+yk3xgCcCEN+pCJTum+uAzSNH3YKs/onaDgAnRSVwOUw
tNW6n1JhXLYl9f5JdhvS
=MOHs
-----END PGP SIGNATURE-----
Merge tag 'char-misc-5.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver updates from Greg KH:
"Here is the large set of char/misc/whatever driver subsystem updates
for 5.12-rc1. Over time it seems like this tree is collecting more and
more tiny driver subsystems in one place, making it easier for those
maintainers, which is why this is getting larger.
Included in here are:
- coresight driver updates
- habannalabs driver updates
- virtual acrn driver addition (proper acks from the x86 maintainers)
- broadcom misc driver addition
- speakup driver updates
- soundwire driver updates
- fpga driver updates
- amba driver updates
- mei driver updates
- vfio driver updates
- greybus driver updates
- nvmeem driver updates
- phy driver updates
- mhi driver updates
- interconnect driver udpates
- fsl-mc bus driver updates
- random driver fix
- some small misc driver updates (rtsx, pvpanic, etc.)
All of these have been in linux-next for a while, with the only
reported issue being a merge conflict due to the dfl_device_id
addition from the fpga subsystem in here"
* tag 'char-misc-5.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (311 commits)
spmi: spmi-pmic-arb: Fix hw_irq overflow
Documentation: coresight: Add PID tracing description
coresight: etm-perf: Support PID tracing for kernel at EL2
coresight: etm-perf: Clarify comment on perf options
ACRN: update MAINTAINERS: mailing list is subscribers-only
regmap: sdw-mbq: use MODULE_LICENSE("GPL")
regmap: sdw: use no_pm routines for SoundWire 1.2 MBQ
regmap: sdw: use _no_pm functions in regmap_read/write
soundwire: intel: fix possible crash when no device is detected
MAINTAINERS: replace my with email with replacements
mhi: Fix double dma free
uapi: map_to_7segment: Update example in documentation
uio: uio_pci_generic: don't fail probe if pdev->irq equals to IRQ_NOTCONNECTED
drivers/misc/vmw_vmci: restrict too big queue size in qp_host_alloc_queue
firewire: replace tricky statement by two simple ones
vme: make remove callback return void
firmware: google: make coreboot driver's remove callback return void
firmware: xilinx: Use explicit values for all enum values
sample/acrn: Introduce a sample of HSM ioctl interface usage
virt: acrn: Introduce an interface for Service VM to control vCPU
...
Some late changes for sdw:
- fix for crash on intel driver
- support for _no_pm IO calls in sdw regmap
-----BEGIN PGP SIGNATURE-----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=eJnY
-----END PGP SIGNATURE-----
Merge tag 'soundwire-2_5.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/vkoul/soundwire into char-misc-next
Vinod writes:
soundwire second update for 5.12-rc1
Some late changes for sdw:
- fix for crash on intel driver
- support for _no_pm IO calls in sdw regmap
* tag 'soundwire-2_5.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/vkoul/soundwire:
regmap: sdw-mbq: use MODULE_LICENSE("GPL")
regmap: sdw: use no_pm routines for SoundWire 1.2 MBQ
regmap: sdw: use _no_pm functions in regmap_read/write
soundwire: intel: fix possible crash when no device is detected
"GPL v2" is the same as "GPL". It exists for historic reasons.
See Documentation/process/license-rules.rst
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Acked-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20210122070634.12825-8-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Use no_pm versions for write and read.
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@linux.intel.com>
Acked-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20210122070634.12825-7-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
sdw_update_slave_status will be invoked when a codec is attached,
and the codec driver will initialize the codec with regmap functions
while the codec device is pm_runtime suspended.
regmap routines currently rely on regular SoundWire IO functions,
which will call pm_runtime_get_sync()/put_autosuspend.
This causes a deadlock where the resume routine waits for an
initialization complete signal that while the initialization complete
can only be reached when the resume completes.
The only solution if we allow regmap functions to be used in resume
operations as well as during codec initialization is to use _no_pm
routines. The duty of making sure the bus is operational needs to be
handled above the regmap level.
Fixes: 7c22ce6e21 ('regmap: Add SoundWire bus support')
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Acked-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20210122070634.12825-6-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Fix the following coccicheck warnings:
./drivers/base/regmap/regcache.c:71:3-18: WARNING: Assignment of
0/1 to bool variable.
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Jiapeng Zhong <abaci-bugfix@linux.alibaba.com>
Link: https://lore.kernel.org/r/1611215961-33725-1-git-send-email-abaci-bugfix@linux.alibaba.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This code will leak "map->debugfs_name" because the if statement is
reversed so it only frees NULL pointers instead of non-NULL. In
fact the if statement is not required and should just be removed
because kfree() accepts NULL pointers.
Fixes: cffa4b2122 ("regmap: debugfs: Fix a memory leak when calling regmap_attach_dev")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://lore.kernel.org/r/X/RQpfAwRdLg0GqQ@mwanda
Signed-off-by: Mark Brown <broonie@kernel.org>
After initializing the regmap through
syscon_regmap_lookup_by_compatible, then regmap_attach_dev to the
device, because the debugfs_name has been allocated, there is no
need to redistribute it again
unreferenced object 0xd8399b80 (size 64):
comm "swapper/0", pid 1, jiffies 4294937641 (age 278.590s)
hex dump (first 32 bytes):
64 75 6d 6d 79 2d 69 6f 6d 75 78 63 2d 67 70 72
dummy-iomuxc-gpr
40 32 30 65 34 30 30 30 00 7f 52 5b d8 7e 42 69
@20e4000..R[.~Bi
backtrace:
[<ca384d6f>] kasprintf+0x2c/0x54
[<6ad3bbc2>] regmap_debugfs_init+0xdc/0x2fc
[<bc4181da>] __regmap_init+0xc38/0xd88
[<1f7e0609>] of_syscon_register+0x168/0x294
[<735e8766>] device_node_get_regmap+0x6c/0x98
[<d96c8982>] imx6ul_init_machine+0x20/0x88
[<0456565b>] customize_machine+0x1c/0x30
[<d07393d8>] do_one_initcall+0x80/0x3ac
[<7e584867>] kernel_init_freeable+0x170/0x1f0
[<80074741>] kernel_init+0x8/0x120
[<285d6f28>] ret_from_fork+0x14/0x20
[<00000000>] 0x0
Fixes: 9b947a13e7 ("regmap: use debugfs even when no device")
Signed-off-by: Xiaolei Wang <xiaolei.wang@windriver.com>
Link: https://lore.kernel.org/r/20201229105046.41984-1-xiaolei.wang@windriver.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This is quite a busy release for regmap with two substantial features
being added:
- Support for register maps Soundwire 1.2 multi-byte operations,
allowing atomic support for registers larger than a single byte.
- Support for relaxed I/O without barriers in MMIO regmaps, allowing
them to be used efficiently on systems where default MMIO operations
include barriers.
There was also an addition and revert of use of the new Soundwire
support for RT715 due to build issues with the driver built in, my tests
only covered building it as a module, the patch wasn't just dropped as
it had already been merged elsewhere.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAl/XdOYACgkQJNaLcl1U
h9DKWwf7BVgrH1vcgOdZ/8xbVnu2pmNGJzHydfV2XD2fHuEgkuVN1dv756HFCzBj
XpHGa+XRGt1j39KsBqhcBOGuCLiTmjmoxWXq4MnBFVHcXBNRk1z6YFtkeZBkRi0j
ZxZNlrrCCaFp8KmqyqMeIU9DbiQ/ITTH/1VBcffnprYI1J9gK4JQE0iisaMIap90
XwKx4VUwT63yVZQGJPW4t65uMUbPTRqcZQzfj3DGhjmkhNI/EvpPU44K11I+op/6
7J9enekMlbOR5t7606h9gAapW1Qt+YrvTwciT9mzGNsmO8MmyUIRQUYuZAzp5RIT
BH5aIRfTUb6lYuktSKI8STrbOUdi/A==
=194Y
-----END PGP SIGNATURE-----
Merge tag 'regmap-v5.11' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap
Pull regmap updates from Mark Brown:
"This is quite a busy release for regmap with two substantial features
being added:
- Support for register maps Soundwire 1.2 multi-byte operations,
allowing atomic support for registers larger than a single byte.
- Support for relaxed I/O without barriers in MMIO regmaps, allowing
them to be used efficiently on systems where default MMIO
operations include barriers.
There was also an addition and revert of use of the new Soundwire
support for RT715 due to build issues with the driver built in, my
tests only covered building it as a module, the patch wasn't just
dropped as it had already been merged elsewhere"
* tag 'regmap-v5.11' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap:
ASoC: rt715: Fix build
regmap: sdw: add required header files
regmap: Remove duplicate `type` field from regmap `regcache_sync` trace event
regmap: Fix order of regmap write log
regmap: mmio: add config option to allow relaxed MMIO accesses
Core:
- Consolidation and robustness changes for irq time accounting
- Cleanup and consolidation of irq stats
- Remove the fasteoi IPI flow which has been proved useless
- Provide an interface for converting legacy interrupt mechanism into
irqdomains
Drivers:
The rare event of not having completely new chip driver code, just new
DT bindings and extensions of existing drivers to accomodate new
variants!
- Preliminary support for managed interrupts on platform devices
- Correctly identify allocation of MSIs proxyied by another device
- Generalise the Ocelot support to new SoCs
- Improve GICv4.1 vcpu entry, matching the corresponding KVM optimisation
- Work around spurious interrupts on Qualcomm PDC
- Random fixes and cleanups
Thanks,
tglx
-----BEGIN PGP SIGNATURE-----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=iytv
-----END PGP SIGNATURE-----
Merge tag 'irq-core-2020-12-15' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull irq updates from Thomas Gleixner:
"Generic interrupt and irqchips subsystem updates. Unusually, there is
not a single completely new irq chip driver, just new DT bindings and
extensions of existing drivers to accomodate new variants!
Core:
- Consolidation and robustness changes for irq time accounting
- Cleanup and consolidation of irq stats
- Remove the fasteoi IPI flow which has been proved useless
- Provide an interface for converting legacy interrupt mechanism into
irqdomains
Drivers:
- Preliminary support for managed interrupts on platform devices
- Correctly identify allocation of MSIs proxyied by another device
- Generalise the Ocelot support to new SoCs
- Improve GICv4.1 vcpu entry, matching the corresponding KVM
optimisation
- Work around spurious interrupts on Qualcomm PDC
- Random fixes and cleanups"
* tag 'irq-core-2020-12-15' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (54 commits)
irqchip/qcom-pdc: Fix phantom irq when changing between rising/falling
driver core: platform: Add devm_platform_get_irqs_affinity()
ACPI: Drop acpi_dev_irqresource_disabled()
resource: Add irqresource_disabled()
genirq/affinity: Add irq_update_affinity_desc()
irqchip/gic-v3-its: Flag device allocation as proxied if behind a PCI bridge
irqchip/gic-v3-its: Tag ITS device as shared if allocating for a proxy device
platform-msi: Track shared domain allocation
irqchip/ti-sci-intr: Fix freeing of irqs
irqchip/ti-sci-inta: Fix printing of inta id on probe success
drivers/irqchip: Remove EZChip NPS interrupt controller
Revert "genirq: Add fasteoi IPI flow"
irqchip/hip04: Make IPIs use handle_percpu_devid_irq()
irqchip/bcm2836: Make IPIs use handle_percpu_devid_irq()
irqchip/armada-370-xp: Make IPIs use handle_percpu_devid_irq()
irqchip/gic, gic-v3: Make SGIs use handle_percpu_devid_irq()
irqchip/ocelot: Add support for Jaguar2 platforms
irqchip/ocelot: Add support for Serval platforms
irqchip/ocelot: Add support for Luton platforms
irqchip/ocelot: prepare to support more SoC
...
The MIPI SoundWire Device Class standard will define audio functionality
beyond the scope of the existing SoundWire 1.2 standard, which is limited
to the bus and interface.
The description is inspired by the USB Audio Class, with "functions",
"entities", "control selectors", "audio clusters". The main difference
with the USB Audio class is that the devices are typically on a motherboard
and descriptors stored in platform firmware instead of being retrieved
from the device.
The current set of devices managed in this patchset are conformant with the
SDCA 0.6 specification and require dedicated drivers since the descriptors
and platform firmware specification is not complete at this time. They do
however rely on the hierarchical addressing required by the SDCA standard.
Future devices conformant with SDCA 1.0 should rely on a class driver.
This series adds support for the hierarchical SDCA addressing and extends
regmap. It then provides 3 codecs for RT711-sdca headset codec, RT1316
amplifier and RT715-scda microphone codec.
Note that the release of this code before the formal adoption of the
SDCA 1.0 specification was formally endorsed by the MIPI Board to make
sure there is no delay for Linux-based support of this specification.
Jack Yu (1):
ASoC/SoundWire: rt715-sdca: First version of rt715 sdw sdca codec
driver
Pierre-Louis Bossart (2):
soundwire: SDCA: add helper macro to access controls
regmap/SoundWire: sdw: add support for SoundWire 1.2 MBQ
Shuming Fan (2):
ASoC/SoundWire: rt1316: Add RT1316 SDCA vendor-specific driver
ASoC/SoundWire: rt711-sdca: Add RT711 SDCA vendor-specific driver
drivers/base/regmap/Kconfig | 6 +-
drivers/base/regmap/Makefile | 1 +
drivers/base/regmap/regmap-sdw-mbq.c | 101 ++
include/linux/regmap.h | 35 +
include/linux/soundwire/sdw_registers.h | 32 +
sound/soc/codecs/Kconfig | 20 +
sound/soc/codecs/Makefile | 6 +
sound/soc/codecs/rt1316-sdw.c | 756 ++++++++++++
sound/soc/codecs/rt1316-sdw.h | 115 ++
sound/soc/codecs/rt711-sdca-sdw.c | 424 +++++++
sound/soc/codecs/rt711-sdca-sdw.h | 101 ++
sound/soc/codecs/rt711-sdca.c | 1481 +++++++++++++++++++++++
sound/soc/codecs/rt711-sdca.h | 246 ++++
sound/soc/codecs/rt715-sdca-sdw.c | 278 +++++
sound/soc/codecs/rt715-sdca-sdw.h | 170 +++
sound/soc/codecs/rt715-sdca.c | 936 ++++++++++++++
sound/soc/codecs/rt715-sdca.h | 124 ++
17 files changed, 4831 insertions(+), 1 deletion(-)
create mode 100644 drivers/base/regmap/regmap-sdw-mbq.c
create mode 100644 sound/soc/codecs/rt1316-sdw.c
create mode 100644 sound/soc/codecs/rt1316-sdw.h
create mode 100644 sound/soc/codecs/rt711-sdca-sdw.c
create mode 100644 sound/soc/codecs/rt711-sdca-sdw.h
create mode 100644 sound/soc/codecs/rt711-sdca.c
create mode 100644 sound/soc/codecs/rt711-sdca.h
create mode 100644 sound/soc/codecs/rt715-sdca-sdw.c
create mode 100644 sound/soc/codecs/rt715-sdca-sdw.h
create mode 100644 sound/soc/codecs/rt715-sdca.c
create mode 100644 sound/soc/codecs/rt715-sdca.h
base-commit: 3650b228f8
--
2.17.1
The SoundWire 1.1 specification only allowed for reads and writes of
bytes. The SoundWire 1.2 specification adds a new capability to
transfer "Multi-Byte Quantities" (MBQ) across the bus. The transfers
still happens one-byte-at-a-time, but the update is atomic.
For example when writing a 16-bit volume, the first byte transferred
is only taken into account when the second byte is successfully
transferred.
The mechanism is symmetrical for read and writes:
- On a read, the address of the last byte to be read is modified by
setting the MBQ bit
- On a write, the address of all but the last byte to be written are
modified by setting the MBQ bit. The address for the last byte relies
on the MBQ bit being cleared.
The current definitions for MBQ-based controls in the SDCA draft
standard are limited to 16 bits for volumes, so for now this is the
only supported format. An update will be provided if and when support
for 24-bit and 32-bit values is specified by the SDCA standard.
One possible objection is that this code could have been handled with
regmap-sdw.c. However this is a new spec addition not handled by every
SoundWire 1.1 and non-SDCA device, so there's no reason to load code
that will never be used.
Also in practice it's extremely unlikely that CONFIG_REGMAP would not
be selected with CONFIG_REGMAP_MBQ selected. However there's no
functional dependency between the two modules so they can be selected
separately.
Reviewed-by: Rander Wang <rander.wang@linux.intel.com>
Reviewed-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/20201103172226.4278-3-yung-chuan.liao@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
I have an error saying that `regcache_sync` has 2 fields named `type`
while using libtraceevent.
Erase the `int field` type, which is not assigned. This field is
introduced by mistake and this commit removes it.
Fixes: 5936008901 ("regmap: Add the regcache_sync trace event")
Signed-off-by: Philippe Duplessis-Guindon <pduplessis@efficios.com>
Link: https://lore.kernel.org/r/20201124135730.9185-1-pduplessis@efficios.com
Signed-off-by: Mark Brown <broonie@kernel.org>
_regmap_write can trigger a _regmap_select_page, which will call
another _regmap_write that will be executed first, but the log shows
the inverse order
Also, keep consistency with _regmap_read which only logs in case of
success
Signed-off-by: Lucas Tanure <tanureal@opensource.cirrus.com>
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20201112150217.459844-1-tanureal@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
irq_domain_create_legacy() takes a fwnode as parameter contrary to
irq_domain_add_legacy() which requires a OF node.
Switch the regmap irq domain creation to use that new function so it is not
longer limited to OF based usage.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20201030165919.86234-6-andriy.shevchenko@linux.intel.com
On some platforms (eg armv7 due to the CONFIG_ARM_DMA_MEM_BUFFERABLE)
MMIO R/W operations always add memory barriers which can increase load,
decrease battery life or in general reduce performance unnecessarily
on devices which access a lot of configuration registers and where
ordering does not matter (eg. media accelerators like the Verisilicon /
Hantro video decoders).
Drivers used to call the relaxed MMIO variants directly but since they
are now accessing the MMIO registers via regmaps (to compensate for
different VPU HW reg layouts via regmap fields), there is a need for a
relaxed API / config to preserve existing behaviour.
Cc: Mark Brown <broonie@kernel.org>
Signed-off-by: Adrian Ratiu <adrian.ratiu@collabora.com>
Link: https://lore.kernel.org/r/20201014203024.954369-1-adrian.ratiu@collabora.com
Signed-off-by: Mark Brown <broonie@kernel.org>
For particular codec HWs have requirement to toggle interrupt clear
register twice 0->1->0. To accommodate it, need to add one more field
(clear_ack) in the regmap_irq struct and update regmap-irq driver to
support it.
Signed-off-by: Laxminath Kasam <lkasam@codeaurora.org>
Link: https://lore.kernel.org/r/1601907440-13373-1-git-send-email-lkasam@codeaurora.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Useful for devices with many fields.
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAl9yPoATHGJyb29uaWVA
a2VybmVsLm9yZwAKCRAk1otyXVSH0JsoB/9zhtYrqKbof0AKuMfEeO+pPo4dC/9l
O7ENgSXCb9PWy0auVpU62ISXBPadbbrQXXe3hJ1Zof5q17lYqbaLM7Uem3bxIYtc
0HHRIb49R1sP+99T2JB3RDu/ykzHJsfxCkLgMR5MvBgS5e3KKf0SqZgNSVTYT4Y5
oPt81sxW56Z8FLrLn0j1sVDXlro4/uBpDOcHyzgq4GWgQ6ACvnIOH+PQUTTcGBfT
LtIkRMO8mHNKsDCy9Qy12NRsaparIbYb7KKEY9IR+6TN+qJ/g5PJQcPmsU6b0NIl
pb7fv4IRTvPDaEPa1g20U88qkSE5H3PXp88R3y/JbSMuFJwWwS2AGwYd
=L+6w
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAl9yPpwTHGJyb29uaWVA
a2VybmVsLm9yZwAKCRAk1otyXVSH0PkDB/9ybt51NqJWyU3JaleY7otD2QvCmvl6
2dzpDncfjYZ8GOhvju74BQM9h/m9EHzb5FQ1yLMKEeICXZwxkDgHiqMLYLN1e6wx
ug5U6lvbT1TmeBa7IJYNNSGH2BKeIDM5Hm2zVvMpEJhF2Y9uAE0HqxjGL3CfbUOv
R2o2K3wgax83FfX86wmYNgkkp4Ri1qviD1Jr90zzFZRr0FAjiyrFHXdfdvK/wUx1
5n9wg+aIehQr1a8cKYQaqWd3HZR6pofmOj1cO4n/By+VEYRWaVds8OKUrqimZ2mE
moX9+ooY3eFdmS6kgtA31bgBFjKxfMNaTzTa4B3kikmxSOKMupQejBn9
=G3GG
-----END PGP SIGNATURE-----
Merge tag 'regmap-field-bulk-api' into regmap-5.10
regmap: Add a bulk field API
Useful for devices with many fields.
Usage of regmap_field_alloc becomes much overhead when number of fields
exceed more than 3.
QCOM LPASS driver has extensively converted to use regmap_fields.
Using new bulk api to allocate fields makes it much more cleaner code to read!
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Tested-by: Srinivasa Rao Mandadapu <srivasam@codeaurora.org>
Link: https://lore.kernel.org/r/20200925164856.10315-2-srinivas.kandagatla@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
While not destroying mutexes doesn't lead to memory leaks, it's still
the correct thing to do for mutex debugging accounting.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Link: https://lore.kernel.org/r/20200928120614.23172-1-brgl@bgdev.pl
Signed-off-by: Mark Brown <broonie@kernel.org>
