After f65aad41772f("MIPS: Cavium: Add EDAC support."), when entering
the "Device Drivers" toplevel menu in menuconfig, the suboptions behind
EDAC appeared merged with the rest of the device drivers types. This was
because the menuconfig option EDAC is querying an EDAC_SUPPORT Kconfig
bool which was defined after the menu definition.
When pushing EDAC_SUPPORT up, before the menu definition, the variable
is defined earlier and the above menuconfig artifact doesn't happen.
Drop a useless menuconfig comment while at it.
Cc: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Borislav Petkov <bp@alien8.de>
Pull MIPS updates from Ralf Baechle:
"The MIPS bits for 3.8. This also includes a bunch fixes that were
sitting in the linux-mips.org git tree for a long time. This pull
request contains updates to several OCTEON drivers and the board
support code for BCM47XX, BCM63XX, XLP, XLR, XLS, lantiq, Loongson1B,
updates to the SSB bus support, MIPS kexec code and adds support for
kdump.
When pulling this, there are two expected merge conflicts in
include/linux/bcma/bcma_driver_chipcommon.h which are trivial to
resolve, just remove the conflict markers and keep both alternatives."
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (90 commits)
MIPS: PMC-Sierra Yosemite: Remove support.
VIDEO: Newport Fix console crashes
MIPS: wrppmc: Fix build of PCI code.
MIPS: IP22/IP28: Fix build of EISA code.
MIPS: RB532: Fix build of prom code.
MIPS: PowerTV: Fix build.
MIPS: IP27: Correct fucked grammar in ops-bridge.c
MIPS: Highmem: Fix build error if CONFIG_DEBUG_HIGHMEM is disabled
MIPS: Fix potencial corruption
MIPS: Fix for warning from FPU emulation code
MIPS: Handle COP3 Unusable exception as COP1X for FP emulation
MIPS: Fix poweroff failure when HOTPLUG_CPU configured.
MIPS: MT: Fix build with CONFIG_UIDGID_STRICT_TYPE_CHECKS=y
MIPS: Remove unused smvp.h
MIPS/EDAC: Improve OCTEON EDAC support.
MIPS: OCTEON: Add definitions for OCTEON memory contoller registers.
MIPS: OCTEON: Add OCTEON family definitions to octeon-model.h
ata: pata_octeon_cf: Use correct byte order for DMA in when built little-endian.
MIPS/OCTEON/ata: Convert pata_octeon_cf.c to use device tree.
MIPS: Remove usage of CEVT_R4K_LIB config option.
...
Drivers for EDAC on Cavium. Supported subsystems are:
o CPU primary caches. These are parity protected only, so only error
reporting.
o Second level cache - ECC protected, provides SECDED.
o Memory: ECC / SECDEC if used with suitable DRAM modules. The driver will
will only initialize if ECC is enabled on a system so is safe to run on
non-ECC memory.
o PCI: Parity error reporting
Since it is very hard to test this sort of code the implementation is very
conservative and uses polling where possible for now.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Reviewed-by: Borislav Petkov <borislav.petkov@amd.com>
Only levels [0:4] are allowed so enforce that. Also, while at it,
massage Kconfig text and add valid debug levels range to the module
parameter description.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Add support for L2 ECC on Calxeda highbank platform.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add support for memory controller on Calxeda Highbank platforms. Highbank
platforms support a single 4GB mini-DIMM with 1-bit correction and 2-bit
detection.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The old EDAC API is broken. It only works fine for systems manufatured
before 2005 and for AMD 64. The reason is that it forces all memory
controller drivers to discover rank info.
Also, it doesn't allow grouping the several ranks into a DIMM.
So, what almost all modern drivers do is to create a fake virtual-rank
information, and use it to cheat the EDAC core to accept the driver.
While this works if the user has enough time to discover what DIMM slot
corresponds to each "virtual-rank" information, it prevents EDAC usage
for users with less available time. It also makes life hard for vendors
that may want to provide a table with their motherboards to the userspace
tool (edac-utils) as each driver has its own logic for the virtual
mapping.
So, the old API should be removed, in favor of a more flexible API that
allows newer drivers to not lie to the EDAC core.
Reviewed-by: Aristeu Rozanski <arozansk@redhat.com>
Cc: Doug Thompson <norsk5@yahoo.com>
Cc: Borislav Petkov <borislav.petkov@amd.com>
Cc: Randy Dunlap <rdunlap@xenotime.net>
Cc: Josh Boyer <jwboyer@redhat.com>
Cc: Hui Wang <jason77.wang@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This driver needs to access PCIe Extended Configuration Space
Registers (0x100~0xfff), to correctly access those registers, we need
to enable PCI_MMCONFIG option. Since this option is not enabled for
X86_64 by default, we let the driver depend on it to prevent users
forgetting to enable this option.
Signed-off-by: Hui Wang <jason77.wang@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The sb_edac driver is marginally useful on a 32-bit kernel, and
currently has 64-bit divide compile errors when building that config.
For now, make this build on only for 64-bit kernels.
Signed-off-by: Josh Boyer <jwboyer@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Some changes on it were required due to changeset cd90cc84c6bf0, that
changed the glue with the MCE logic.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Both AMD and Intel i7 EDAC drivers use MCE features and are thus
dependent of this functionality present in the kernel. Express this in
Kconfig so that randconfig builds don't break.
Reported-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Acked-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Remove edac_mce pieces and use the normal MCE decoder notifier chain by
retaining the same functionality with considerably less code.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This reverts commit af9d220bac.
It turns out that one was meant to be applied on top of the edac.git
tree in -next that has more i7core_edac changes, but that wasn't clear
in the original email.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Borislav Petkov <borislav.petkov@amd.com>
Cc: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Both AMD and Intel i7 EDAC drivers use MCE features and are thus
dependent of this functionality present in the kernel. Express this in
Kconfig so that randconfig builds don't break.
Reported-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Acked-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add tile support for the EDAC driver, which provides unified system
error (memory, PCI, etc.) reporting. For now, the TILEPro port
reports memory correctable error (CE) only.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
* 'devel' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/edac: (25 commits)
i7300_edac: Properly initialize per-csrow memory size
V4L/DVB: i7300_edac: better initialize page counts
MAINTAINERS: Add maintainer for i7300-edac driver
i7300-edac: CodingStyle cleanup
i7300_edac: Improve comments
i7300_edac: Cleanup: reorganize the file contents
i7300_edac: Properly detect channel on CE errors
i7300_edac: enrich FBD error info for corrected errors
i7300_edac: enrich FBD error info for fatal errors
i7300_edac: pre-allocate a buffer used to prepare err messages
i7300_edac: Fix MTR x4/x8 detection logic
i7300_edac: Make the debug messages coherent with the others
i7300_edac: Cleanup: remove get_error_info logic
i7300_edac: Add a code to cleanup error registers
i7300_edac: Add support for reporting FBD errors
i7300_edac: Properly detect the type of error correction
i7300_edac: Detect if the device is on single mode
i7300_edac: Adds detection for enhanced scrub mode on x8
i7300_edac: Clear the error bit after reading
i7300_edac: Add error detection code for global errors
...
Add sysfs injection facilities for testing of the MCE decoding code.
Remove large parts of amd64_edac_dbg.c, as a result, which did only
NB MCE injection anyway and the new injection code supports that
functionality already.
Add an injection module so that MCE decoding code in production kernels
like those in RHEL and SLES can be tested.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
The file names are somehow misleading as the code is not specific to
AMD K8 CPUs anymore. The files accomodate code for other AMD CPU
northbridges as well.
Same is true for the config option which is valid for AMD CPU
northbridges in general and not specific to K8.
Signed-off-by: Andreas Herrmann <andreas.herrmann3@amd.com>
LKML-Reference: <20100917160343.GD4958@loge.amd.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
This option differs from EDAC_DEBUG only by printing the file and
line of where the debug statement is placed, which contains unneeded
information. So remove it.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Acked-by: Doug Thompson <dougthompson@xmission.com>
Since commit 5753c082f6 ("powerpc/85xx:
Kconfig cleanup"), there is no MPC85xx Kconfig symbol anymore, so the
driver became non-selectable.
This patch fixes the issue by switching to PPC_85xx symbol.
Signed-off-by: Anton Vorontsov <avorontsov@mvista.com>
Cc: Doug Thompson <dougthompson@xmission.com>
Cc: Peter Tyser <ptyser@xes-inc.com>
Cc: Dave Jiang <djiang@mvista.com>
Cc: Kumar Gala <galak@kernel.crashing.org>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
edac_mce module is an interface module that gets mcelog data and
forwards to any registered edac module that expects to receive data via
mce.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This driver is meant to support i7 core/i7core extreme desktop
processors and Xeon 35xx/55xx series with integrated memory controller.
It is likely that it can be expanded in the future to work with other
processor series based at the same Memory Controller design.
For now, it has just a few MCH status reads.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This converts the MCE decoding logic into a standalone config
option which can be built-in or a module, the first one being the
default for MCEs happening early on in the boot process.
This, beyond being separated in a cleaner way, also saves RAM by
making the decoding logic modular.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Andi Kleen <andi@firstfloor.org>
LKML-Reference: <20091002133148.GD28682@aftab>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
A driver for the Intel 3200 and 3210 memory controllers. It has only had
light testing so far, and currently makes no attempt to decode error
addresses at anything finer than csrow granularity.
Signed-off-by: Jason Uhlenkott <juhlenko@akamai.com>
Signed-off-by: Doug Thompson <dougthompson@xmission.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add support for the Freescale MPC83xx memory controller to the existing
driver for the Freescale MPC85xx memory controller. The only difference
between the two processors are in the CS_BNDS register parsing code, which
has been changed so it will work on both processors.
The L2 cache controller does not exist on the MPC83xx, but the OF
subsystem will not use the driver if the device is not present in the OF
device tree.
I had to change the nr_pages calculation to make the math work out. I
checked it on my board and did the math by hand for a 64GB 85xx using 64K
pages. In both cases, nr_pages * PAGE_SIZE comes out to the correct
value.
Signed-off-by: Ira W. Snyder <iws@ovro.caltech.edu>
Signed-off-by: Doug Thompson <dougthompson@xmission.com>
Cc: Kumar Gala <galak@gate.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
-tip testing found the following build failure (config attached):
drivers/built-in.o: In function `amd64_check':
amd64_edac.c:(.text+0x3e9491): undefined reference to `amd_decode_nb_mce'
drivers/built-in.o: In function `amd64_init_2nd_stage':
amd64_edac.c:(.text+0x3e9b46): undefined reference to `amd_report_gart_errors'
amd64_edac.c:(.text+0x3e9b55): undefined reference to `amd_register_ecc_decoder'
drivers/built-in.o: In function `amd64_nbea_store':
amd64_edac_dbg.c:(.text+0x3ea22e): undefined reference to `amd_decode_nb_mce'
drivers/built-in.o: In function `amd64_remove_one_instance':
amd64_edac.c:(.devexit.text+0x3eea): undefined reference to `amd_report_gart_errors'
amd64_edac.c:(.devexit.text+0x3ef6): undefined reference to `amd_unregister_ecc_decoder'
the AMD EDAC code has a dependency on CONFIG_CPU_SUP_AMD facilities. The
patch below solves the problem here.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Introduce IBM CPC925 EDAC driver, which makes use of ECC, CPU and
HyperTransport Link error detections and corrections on the IBM
CPC925 Bridge and Memory Controller.
[akpm@linux-foundation.org: cleanup]
Signed-off-by: Harry Ciao <qingtao.cao@windriver.com>
Cc: Doug Thompson <norsk5@yahoo.com>
Cc: Michael Ellerman <michael@ellerman.id.au>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Kumar Gala <galak@gate.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Prevent EDAC compilation units from being built by default and let the
user explicitly select the needed modules.
Acked-by: Randy Dunlap <randy.dunlap@oracle.com>
Tested-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
While at it, fix a link failure when !K8_NB.
Acked-by: Doug Thompson <dougthompson@xmission.com>
Acked-by: Randy Dunlap <randy.dunlap@oracle.com>
Tested-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Also, link into Kbuild by adding Kconfig and Makefile entries.
Borislav:
- Kconfig/Makefile splitting
- use zero-sized arrays for the sysfs attrs if not enabled
- rename sysfs attrs to more conform values
- shorten CONFIG_ names
- make multiple structure members assignment vertically aligned
- fix/cleanup comments
- fix function return value patterns
- fix err labels
- fix a memleak bug caught by Ingo
- remove the NUMA dependency and use num_k8_northbrides for initializing
a driver instance per NB.
- do not copy the pvt contents into the mci struct in
amd64_init_2nd_stage() and save it in the mci->pvt_info void ptr
instead.
- cleanup debug calls
- simplify amd64_setup_pci_device()
Reviewed-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Doug Thompson <dougthompson@xmission.com>
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
The amd8111_edac.c driver will fail allmodconfig on architectures other
than PPC, introduce Kconfig dependency to avoid this, since both AMD8111
and AMD8131 chips are only adopted on Maple so far.
Signed-off-by: Harry Ciao <qingtao.cao@windriver.com>
Cc: Doug Thompson <norsk5@yahoo.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This adds support for an EDAC memory controller adaptation driver for the
"ibm,sdram-4xx-ddr2" ECC controller realized in the AMCC PowerPC 405EX[r].
At present, this driver has been developed and tested against the
controller realization in the AMCC PPC405EX[r] on the AMCC Kilauea and
Haleakala boards (256 MiB w/o ECC memory soldered onto the board) and a
proprietary board based on those designs (128 MiB ECC memory, also
soldered onto the board).
In the future, dynamic feature detection and handling needs to be added
for the other realizations of this controller found in the 440SP, 440SPe,
460EX, 460GT and 460SX.
Eventually, this driver will likely be evolved and adapted to the above
variant realizations of this controller as well as broken apart to handle
the other known ECC-capable controllers prevalent in other PPC4xx
processors:
- IBM SDRAM (405GP, 405CR and 405EP) "ibm,sdram-4xx"
- IBM DDR1 (440GP, 440GX, 440EP and 440GR) "ibm,sdram-4xx-ddr"
- Denali DDR1/DDR2 (440EPX and 440GRX) "denali,sdram-4xx-ddr2"
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Grant Erickson <gerickson@nuovations.com>
Signed-off-by: Doug Thompson <dougthompson@xmission.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
After 3 years, this is a patch to remove the EXPERIMENTAL tag on EDAC. We
now have many module drivers submitters in EDAC and believe EDAC is no
longer EXPERIMENTAL
Signed-off-by: Doug Thompson <dougthompson@xmission.com
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
A patch for making a debugging information more verbose for use in
development debugging.
By enabling the new option "More verbose debugging", information about
source file and line number will be added to debugging message.
This is sample output,
EDAC MC0: Giving out device to 'e7xxx_edac' 'E7205': DEV 0000:00:00.0
EDAC DEBUG: in drivers/edac/edac_pci.c, line at 48: edac_pci_alloc_ctl_info()
EDAC DEBUG: in drivers/edac/edac_pci.c, line at 334: edac_pci_add_device()
^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
Signed-off-by: Hitoshi Mitake <h.mitake@gmail.com>
Signed-off-by: Doug Thompson <dougthompson@xmission.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Since the QPACE (Chromodynamics Parallel Computing on the
Cell Broadband Engine) platform doesn't use a iommu, doesn't
have PCI devices and a MPIC much lesser setup and
configurations are needed. So far all devices are detected
as OF device. A notifier function is used to set the dma_ops
for the of_platform bus. Further this patch splits the
PPC_CELL_NATIVE into PPC_CELL_COMMON which are parts that are
shared with the QPACE platform and the rest.
Signed-off-by: Benjamin Krill <ben@codiert.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
I wrote a new module for Intel X38 chipset. This chipset is very similar
to Intel 3200 chipset, but there are some different points, so I copyed
i3200_edac.c and modified.
This is Intel's web page describing this chipset.
http://www.intel.com/Products/Desktop/Chipsets/X38/X38-overview.htm
I've tested this new module with broken memory, and it seems to be working
well.
Signed-off-by: Hitoshi Mitake <mitake@clustcom.com>
Signed-off-by: Doug Thompson <dougthompson@xmission.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Preliminary support for the Intel 5100 MCH. CE and UE errors are reported
along with the current DIMM label information and other memory parameters.
Reasons why this is preliminary:
1) This chip has 2 independent memory controllers which, for best
perforance, use interleaved accesses to the DDR2 memory. This
architecture does not map very well to the current edac data structures
which depend on symmetric channel access to the interleaved data.
Without core changes, the best I could do for now is to map both memory
controllers to different csrows (first all ranks of controller 0, then
all ranks of controller 1). Someone much more familiar with the edac
core than I will probably need to come up with a more general data
structure to handle the interleaving and de-interleaving of the two
memory controllers.
2) I have not yet tackled the de-interleaving of the rank/controller
address space into the physical address space of the CPU. There is
nothing fundamentally missing, it is just ending up to be a lot of
code, and I'd rather keep it separate for now, esp since it doesn't
work yet...
3) The code depends on a particular i5100 chip select to DIMM mainboard
chip select mapping. This mapping seems obvious to me in order to
support dual and single ranked memory, but it is not unique and DIMM
labels could be wrong on other mainboards. There is no way to query
this mapping that I know of.
4) The code requires that the i5100 is in 32GB mode. Only 4 ranks per
controller, 2 ranks per DIMM are supported. I do not have hardware
(nor do I expect to have hardware anytime soon) for the 48GB (6 ranks
per controller) mode.
5) The serial presence detect code should be broken out into a "real"
i2c driver so that decode-dimms.pl can work.
Signed-off-by: Arthur Jones <ajones@riverbed.com>
Signed-off-by: Doug Thompson <dougthompson@xmission.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Modified to run on x86_64 as well as x86
i3000_edac builds (and runs) fine on x86_64.
Signed-off-by: Jason Uhlenkott <juhlenko@akamai.com>
Signed-off-by: Doug Thompson <dougthompson@xmission.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
