Remove ena_device_io_suspend/resume() methods
Those methods were intend to be used by the device to trigger
suspend/resume but eventually it was dropped.
Signed-off-by: Netanel Belgazal <netanel@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ena admin commands timeout is in resolutions of 100ms.
Therefore, When the driver works in polling mode, it sleeps for 100ms
each time. The overall boot time of the ENA driver is ~1.5 sec.
To reduce the boot time, This change modifies the granularity of
the sleeps to 5ms.
This change improves the boot time to 220ms.
Signed-off-by: Netanel Belgazal <netanel@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ethtool ena_get_channels() expose the max number of queues as the max
number of queues ENA supports (128 queues) and not the actual number
of created queues.
Signed-off-by: Netanel Belgazal <netanel@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Decrease log level of checksum errors as these messages can be
triggered remotely by bad packets.
Signed-off-by: Netanel Belgazal <netanel@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Out of order flow is not working for iWARP.
This patch got cut out from initial series that added out
of order support for iWARP.
Make out of order code common for iWARP and iSCSI.
Add new configuration option CONFIG_QED_OOO. Set by
qedr and qedi Kconfigs.
Fixes: d1abfd0b4e ("qed: Add iWARP out of order support")
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: Manish Rangankar <Manish.Rangankar@cavium.com>
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When using tc qdisc, dcb_ops->setup_tc is used to tell hclge_dcb
module to do the tm related setup. Only TC_MQPRIO_MODE_CHANNEL
offload mode is supported.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
40GbE Intel Wired LAN Driver Updates 2017-10-17
This series contains updates to i40e and ethtool.
Alan provides most of the changes in this series which are mainly fixes
and cleanups. Renamed the ethtool "cmd" variable to "ks", since the new
ethtool API passes us ksettings structs instead of command structs.
Cleaned up an ifdef that was not accomplishing anything. Added function
header comments to provide better documentation. Fixed two issues in
i40e_get_link_ksettings(), by calling
ethtool_link_ksettings_zero_link_mode() to ensure the advertising and
link masks are cleared before we start setting bits. Cleaned up and fixed
code comments which were incorrect. Separated the setting of autoneg in
i40e_phy_types_to_ethtool() into its own conditional to clarify what PHYs
support and advertise autoneg, and makes it easier to add new PHY types in
the future. Added ethtool functionality to intersect two link masks
together to find the common ground between them. Overhauled i40e to
ensure that the new ethtool API macros are being used, instead of the
old ones. Fixed the usage of unsigned 64-bit division which is not
supported on all architectures.
Sudheer adds support for 25G Active Optical Cables (AOC) and Active Copper
Cables (ACC) PHY types.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Comment is no longer valid for a long time now.
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change just renames the FMan driver modules, using a common prefix
for the DPAA FMan and DPAA Ethernet drivers. Besides making the names more
aligned, this allows writing udev rules that match on either driver name,
if needed, using the fsl_dpaa_* prefix. The change of netdev dev required
for the DSA probing makes the previous rules written using this prefix
fail, this change makes them work again, ensuring backwards compatibility
for their users.
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change device used for DMA mapping to the MAC device that is an
of_device, with proper DMA ops. Using this device for the netdevice
should also address the issue with DSA scenarios that need the
netdevice to be backed by an of_device.
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The FMan MAC driver allocates a platform device for the Ethernet
driver to probe on. Setting pdev->dev.of_node with the MAC node
triggers the MAC driver probing of the new platform device. While
this fails quickly and does not affect the functionality of the
drivers, it is incorrect and must be removed. This was added to
address a report that DSA code using of_find_net_device_by_node()
is unable to use the DPAA interfaces. Error message seen before
this fix:
fsl_mac dpaa-ethernet.0: __devm_request_mem_region(mac) failed
fsl_mac: probe of dpaa-ethernet.0 failed with error -16
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Removes unused timer and its old initialization call.
Cc: Pantelis Antoniou <pantelis.antoniou@gmail.com>
Cc: Vitaly Bordug <vbordug@ru.mvista.com>
Cc: linuxppc-dev@lists.ozlabs.org
Cc: netdev@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly. Switches test of .data field to
.function, since .data will be going away.
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Cc: intel-wired-lan@lists.osuosl.org
Cc: netdev@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly. Switches test of .data field to
.function, since .data will be going away.
Cc: Yisen Zhuang <yisen.zhuang@huawei.com>
Cc: Salil Mehta <salil.mehta@huawei.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: lipeng <lipeng321@huawei.com>
Cc: Lin Yun Sheng <linyunsheng@huawei.com>
Cc: Kejian Yan <yankejian@huawei.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: netdev@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly.
Cc: Jon Mason <jdmason@kudzu.us>
Cc: netdev@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly.
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: netdev@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly.
Cc: Russell King <linux@armlinux.org.uk>
Cc: linux-arm-kernel@lists.infradead.org
Cc: netdev@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly.
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Philippe Reynes <tremyfr@gmail.com>
Cc: Jarod Wilson <jarod@redhat.com>
Cc: Shannon Nelson <shannon.nelson@oracle.com>
Cc: Rob Herring <robh@kernel.org>
Cc: chris hyser <chris.hyser@oracle.com>
Cc: Tushar Dave <tushar.n.dave@oracle.com>
Cc: Tobias Klauser <tklauser@distanz.ch>
Cc: netdev@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Acked-by: Shannon Nelson <shannon.nelson@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly.
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Johannes Berg <johannes.berg@intel.com>
Cc: Jarod Wilson <jarod@redhat.com>
Cc: Rob Herring <robh@kernel.org>
Cc: netdev@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly.
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Zhu Yanjun <yanjun.zhu@oracle.com>
Cc: Philippe Reynes <tremyfr@gmail.com>
Cc: netdev@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly.
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Johannes Berg <johannes.berg@intel.com>
Cc: Jarod Wilson <jarod@redhat.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Philippe Reynes <tremyfr@gmail.com>
Cc: netdev@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly.
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jarod Wilson <jarod@redhat.com>
Cc: Tobias Klauser <tklauser@distanz.ch>
Cc: Philippe Reynes <tremyfr@gmail.com>
Cc: netdev@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly.
Cc: Rasesh Mody <rasesh.mody@cavium.com>
Cc: Sudarsana Kalluru <sudarsana.kalluru@cavium.com>
Cc: Dept-GELinuxNICDev@cavium.com
Cc: netdev@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly.
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Jarod Wilson <jarod@redhat.com>
Cc: Philippe Reynes <tremyfr@gmail.com>
Cc: netdev@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly.
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Johannes Berg <johannes.berg@intel.com>
Cc: Eric Dumazet <edumazet@google.com>
Cc: netdev@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly.
Cc: Steffen Klassert <klassert@mathematik.tu-chemnitz.de>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jarod Wilson <jarod@redhat.com>
Cc: netdev@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly.
Cc: "David S. Miller" <davem@davemloft.net>
Cc: David Howells <dhowells@redhat.com>
Cc: Jarod Wilson <jarod@redhat.com>
Cc: Stephen Hemminger <stephen@networkplumber.org>
Cc: Johannes Berg <johannes.berg@intel.com>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Philippe Reynes <tremyfr@gmail.com>
Cc: "yuval.shaia@oracle.com" <yuval.shaia@oracle.com>
Cc: netdev@vger.kernel.org
Cc: linux-parisc@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly.
Cc: Jon Mason <jdmason@kudzu.us>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Miroslav Lichvar <mlichvar@redhat.com>
Cc: Jarod Wilson <jarod@redhat.com>
Cc: Eric Dumazet <edumazet@google.com>
Cc: stephen hemminger <stephen@networkplumber.org>
Cc: netdev@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly.
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: netdev@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly.
Cc: "David S. Miller" <davem@davemloft.net>
Cc: "yuval.shaia@oracle.com" <yuval.shaia@oracle.com>
Cc: Tobias Klauser <tklauser@distanz.ch>
Cc: Jarod Wilson <jarod@redhat.com>
Cc: Philippe Reynes <tremyfr@gmail.com>
Cc: netdev@vger.kernel.org
Cc: linux-parisc@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
helper to pass the timer pointer explicitly.
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: bcm-kernel-feedback-list@broadcom.com
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Jarod Wilson <jarod@redhat.com>
Cc: netdev@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly.
Cc: Samuel Chessman <chessman@tux.org>
Cc: netdev@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch correctly sets the number of additional header descriptors
that will be sent in an indirect SCRQ entry.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When an EMAD is transmitted, a timeout work item is scheduled with a
delay of 200ms, so that another EMAD will be retried until a maximum of
five retries.
In certain situations, it's possible for the function waiting on the
EMAD to be associated with a work item that is queued on the same
workqueue (`mlxsw_core`) as the timeout work item. This results in
flushing a work item on the same workqueue.
According to commit e159489baa ("workqueue: relax lockdep annotation
on flush_work()") the above may lead to a deadlock in case the workqueue
has only one worker active or if the system in under memory pressure and
the rescue worker is in use. The latter explains the very rare and
random nature of the lockdep splats we have been seeing:
[ 52.730240] ============================================
[ 52.736179] WARNING: possible recursive locking detected
[ 52.742119] 4.14.0-rc3jiri+ #4 Not tainted
[ 52.746697] --------------------------------------------
[ 52.752635] kworker/1:3/599 is trying to acquire lock:
[ 52.758378] (mlxsw_core_driver_name){+.+.}, at: [<ffffffff811c4fa4>] flush_work+0x3a4/0x5e0
[ 52.767837]
but task is already holding lock:
[ 52.774360] (mlxsw_core_driver_name){+.+.}, at: [<ffffffff811c65c4>] process_one_work+0x7d4/0x12f0
[ 52.784495]
other info that might help us debug this:
[ 52.791794] Possible unsafe locking scenario:
[ 52.798413] CPU0
[ 52.801144] ----
[ 52.803875] lock(mlxsw_core_driver_name);
[ 52.808556] lock(mlxsw_core_driver_name);
[ 52.813236]
*** DEADLOCK ***
[ 52.819857] May be due to missing lock nesting notation
[ 52.827450] 3 locks held by kworker/1:3/599:
[ 52.832221] #0: (mlxsw_core_driver_name){+.+.}, at: [<ffffffff811c65c4>] process_one_work+0x7d4/0x12f0
[ 52.842846] #1: ((&(&bridge->fdb_notify.dw)->work)){+.+.}, at: [<ffffffff811c65c4>] process_one_work+0x7d4/0x12f0
[ 52.854537] #2: (rtnl_mutex){+.+.}, at: [<ffffffff822ad8e7>] rtnl_lock+0x17/0x20
[ 52.863021]
stack backtrace:
[ 52.867890] CPU: 1 PID: 599 Comm: kworker/1:3 Not tainted 4.14.0-rc3jiri+ #4
[ 52.875773] Hardware name: Mellanox Technologies Ltd. "MSN2100-CB2F"/"SA001017", BIOS 5.6.5 06/07/2016
[ 52.886267] Workqueue: mlxsw_core mlxsw_sp_fdb_notify_work [mlxsw_spectrum]
[ 52.894060] Call Trace:
[ 52.909122] __lock_acquire+0xf6f/0x2a10
[ 53.025412] lock_acquire+0x158/0x440
[ 53.047557] flush_work+0x3c4/0x5e0
[ 53.087571] __cancel_work_timer+0x3ca/0x5e0
[ 53.177051] cancel_delayed_work_sync+0x13/0x20
[ 53.182142] mlxsw_reg_trans_bulk_wait+0x12d/0x7a0 [mlxsw_core]
[ 53.194571] mlxsw_core_reg_access+0x586/0x990 [mlxsw_core]
[ 53.225365] mlxsw_reg_query+0x10/0x20 [mlxsw_core]
[ 53.230882] mlxsw_sp_fdb_notify_work+0x2a3/0x9d0 [mlxsw_spectrum]
[ 53.237801] process_one_work+0x8f1/0x12f0
[ 53.321804] worker_thread+0x1fd/0x10c0
[ 53.435158] kthread+0x28e/0x370
[ 53.448703] ret_from_fork+0x2a/0x40
[ 53.453017] mlxsw_spectrum 0000:01:00.0: EMAD retries (2/5) (tid=bf4549b100000774)
[ 53.453119] mlxsw_spectrum 0000:01:00.0: EMAD retries (5/5) (tid=bf4549b100000770)
[ 53.453132] mlxsw_spectrum 0000:01:00.0: EMAD reg access failed (tid=bf4549b100000770,reg_id=200b(sfn),type=query,status=0(operation performed))
[ 53.453143] mlxsw_spectrum 0000:01:00.0: Failed to get FDB notifications
Fix this by creating another workqueue for EMAD timeouts, thereby
preventing the situation of a work item trying to flush a work item
queued on the same workqueue.
Fixes: caf7297e7a ("mlxsw: core: Introduce support for asynchronous EMAD register access")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reported-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
According to the ASPEED datasheet, gigabit speeds require a clock of
100MHz or higher. Other speeds require 25MHz or higher. This patch
configures a 100MHz clock if the system has a direct-attached
PHY, or 25MHz if the system is running NC-SI which is limited to 100MHz.
There appear to be no other upstream users of the FTGMAC100 driver it is
hard to know the clocking requirements of other platforms. Therefore a
conservative approach was taken with enabling clocks. If the platform is
not ASPEED, both requesting the clock and configuring the speed is
skipped.
Signed-off-by: Joel Stanley <joel@jms.id.au>
Tested-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 52eb1ff93e98 ("i40e: Add support setting TC max bandwidth rates")
and commit 1ea6f21ae530 ("i40e: Refactor VF BW rate limiting") add some
needed functionality for TC bandwidth rate limiting. Unfortunately they
introduce several usages of unsigned 64-bit division which needs to be
handled special by the kernel to support all architectures.
Fixes: 52eb1ff93e98 ("i40e: Add support setting TC max bandwidth
rates")
Fixes: 1ea6f21ae530 ("i40e: Refactor VF BW rate limiting")
Signed-off-by: Alan Brady <alan.brady@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This finishes off the conversion to the new ethtool API by removing the
old macros being used in i40e_set_link_ksettings and replacing them with
shiny new ones.
This conversion also allows us to provide link speed support for new 25G
and 10G macros which is included here as well.
Signed-off-by: Alan Brady <alan.brady@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This variable isn't actually very descriptive and makes the code a bit
confusing as to what it is being used for. This patch enhances the
variable with the longer name, 'autoneg_changed', which makes it clear
we are concerned with autoneg changing in this context.
Signed-off-by: Alan Brady <alan.brady@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This removes references to old ethtool API macros and functions in
i40e_get_settings_link_up as part of the process of converting to the
new API. The new API also allows us to provide more explicit support
for new 25G and 10G PHY types so some of the PHY types have been
adjusted where necessary as well.
Signed-off-by: Alan Brady <alan.brady@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We are still largely using the old ethtool API macros. This is
problematic because eventually they will be removed and they only
support 32 bits of PHY types.
This overhauls i40e_phy_type_to_ethtool to use only the new API. Doing
this also allows us to provide much better support for newer 25G and 10G
PHY types which is included here as well.
The remaining usages of the old ethtool API will be addressed in other
patches in the series.
Signed-off-by: Alan Brady <alan.brady@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds support for 25G Active Optical Cables (AOC) and Active
Copper Cables (ACC) PHY types.
Signed-off-by: Sudheer Mogilappagari <sudheer.mogilappagari@intel.com>
Signed-off-by: Krzysztof Malek <krzysztof.malek@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This separates the setting of autoneg in i40e_phy_types_to_ethtool into
its own conditional. Doing this adds clarity as what PHYs
support/advertise autoneg and makes it easier to add new PHY types in
the future.
This also fixes an issue on devices with CRT_RETIMER where advertising
autoneg was being set, but supported autoneg was not.
Signed-off-by: Alan Brady <alan.brady@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
There's a number of minor incidental whitespace issues in this file.
This addresses most of the ones I could find.
Signed-off-by: Alan Brady <alan.brady@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Someone forgot a word in this comment and it's confusing without it.
Signed-off-by: Alan Brady <alan.brady@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The function header erroneously listed 'phy_types' as a parameter. The
correct parameter is 'pf'.
Signed-off-by: Alan Brady <alan.brady@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This fixes two issues in i40e_get_link_ksettings. It adds calls to
ethtool_link_ksettings_zero_link_mode to make sure advertising and
supported link masks are cleared before we start setting bits in them.
This also replaces some funky bit manipulations with a much nicer call
to ethtool_link_ksettings_del_link_mode when removing link modes.
Signed-off-by: Alan Brady <alan.brady@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Someone left this poor little function naked with no header. This
dresses it up in a proper function header it deserves.
Signed-off-by: Alan Brady <alan.brady@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This 'ifdef' doesn't accomplish anything so remove it.
Signed-off-by: Alan Brady <alan.brady@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
After the switch to the new ethtool API, ethtool passes us
ethtool_ksettings structs instead of ethtool_command structs, however we
were still referring to them as 'cmd' variables. This renames them to
'ks' variables which makes the code easier to understand.
Signed-off-by: Alan Brady <alan.brady@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Formerly, IPIP entries were created lazily by next hops that referenced
an offloadable IP-in-IP netdevice. However now that they are created
eagerly as a reaction to events on such netdevices, the reference
counting is useless. Hence drop it.
The routes whose next hops reference an offloaded IP-in-IP netdevice
actually linger around a bit after their device is unregistered.
However, mlxsw_sp_ipip_entry_destroy() also destroys the backing
loopback, and mlxsw_sp_rif_destroy() transitively (via
mlxsw_sp_nexthop_rif_gone_sync()) calls mlxsw_sp_nexthop_ipip_fini(),
which unlinks the IPIP entry from a next hop. Thus no dangling pointers
are left behind for the brief window after netdevice is gone, but routes
not yet.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
IPIP entries are created as soon as an offloadable device is created.
That means that when such a device is later moved to a different VRF,
the loopback device that backs the tunnel is wrong.
Thus when an offloadable encapsulating netdevice moves from one VRF to
another, make sure that the loopback is updated as necessary.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Current code for offloading IP-in-IP tunneling assumes that there is no
decap without encap. But that's never true for IPv6 overlays, and is not
true for IPv4 ones either, if net.ipv4.conf.*.rp_filter is unset.
To support decap-only tunnels, an IPIP entry is now created as soon as
an offloadable tunneling device is created. When that netdevice is up'd,
a decap route is looked up and possibly offloaded. Thus decap is not
handled implicitly as part of mlxsw_sp_ipip_entry_get() call anymore,
but needs to be done explicitly after the get, if desired.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
So far, all netdevice notifications that the driver cared about were
related to its own ports, and mlxsw_sp could be retrieved from the
netdevice's private data. For IP-in-IP offloading however, the driver
cares about events on foreign netdevices, and getting at mlxsw_sp or
router data structures from the handler is inconvenient.
Therefore move the netdevice notifier blocks from global scope to struct
mlxsw_sp to allow retrieval from the notifier block pointer itself.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The notifier cause a link error when NET_DSA is a loadable
module:
drivers/net/ethernet/broadcom/bcmsysport.o: In function `bcm_sysport_remove':
bcmsysport.c:(.text+0x1582): undefined reference to `unregister_dsa_notifier'
drivers/net/ethernet/broadcom/bcmsysport.o: In function `bcm_sysport_probe':
bcmsysport.c:(.text+0x278d): undefined reference to `register_dsa_notifier'
This adds a dependency that forces the systemport driver to be
a loadable module as well when that happens, but otherwise
allows it to be built normally when DSA is either built-in or
completely disabled.
Fixes: d156576362 ("net: systemport: Establish lower/upper queue mapping")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This removes custom flag handling.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Saeed Mahameed says:
====================
mlx5-updates-2017-10-11: IPoIB Multi Pkey support
This series provides the support for IPoIB Multi Pkey.
InfiniBand Pkeys are the equivalent of Ethernet vlans.
Currently IPoIB device driver supports only default Pkey and IPoIB Pkey child
interfaces are not supported with IPoIB offloads mode, this series will add
the support for that by allowing creating mlx5 multiple IPoIB netdevices with
a non-default Pkey.
mlx5 IPoIB Pkey child interface is smaller version of mlx5i IPoIB interfaces and shares
most of its resources with the parent IPoIB interface, namely RX steering and ring
queue resources.
The only mlx5 resources a child Pkey interface will be creating are the TX rings,
since they should be assigned to a specific Pkey.
mlx5i Pkey netdev is implemented via new mlx5e netdev profile implemented in
mlx5/core/ipoib/ipoib_vlan.c.
The series starts with a refactoring of mlx5e PTP and mlx5 clock implementation
to move the code to be part of mlx5 core rather than mlx5e netdevice, in order to
make mlx5 clock and PTP registration part of the core to be shared with mlx5e
master Ethernet netdev/IPoIB parent netdev and mlx5_ib in the near future.
Add the support for attaching multiple underlay QPs for the different Pkeys
in mlx5 core RX steering.
Add Pkey index to rdma_netdev to add the ability to set PKEY index to lower
IPoIB offload netdev.
Use hash-table to map between DQPN (Destination QP number) to child netdev
for the IPoIB parent netdev to forward RX packets to the corresponding
child Pkey netdev, since the RX rings are shared.
The reset of the series adds the ipoib child Pkey: mlx5e netdev profile,
netdev nods implementation and minimal set of ethtool callbacks.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
hwrm_send_message() is replaced with _hwrm_send_message(), and
hwrm_cmd_lock mutex lock is grabbed for the whole period of
firmware call until the firmware DCB parameters have been copied.
This will prevent possible corruption of the firmware data.
Fixes: 7df4ae9fe8 ("bnxt_en: Implement DCBNL to support host-based DCBX.")
Signed-off-by: Sankar Patchineelam <sankar.patchineelam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In bnxt_find_nvram_item(), it is copying firmware response data after
releasing the mutex. This can cause the firmware response data
to be corrupted if the next firmware response overwrites the response
buffer. The rare problem shows up when running ethtool -i repeatedly.
Fix it by calling the new variant _hwrm_send_message_silent() that requires
the caller to take the mutex and to release it after the response data has
been copied.
Fixes: 3ebf6f0a09 ("bnxt_en: Add installed-package version reporting via Ethtool GDRVINFO")
Reported-by: Sarveswara Rao Mygapula <sarveswararao.mygapula@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In bnxt_sriov_enable(), we calculate to see if we have enough hardware
resources to enable the requested number of VFs. The logic to check
for minimum completion rings and statistics contexts is missing. Add
the required checks so that VF configuration won't fail.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
PCIE PCIE_EP_REG_LINK_STATUS_CONTROL register is only defined in PF
config space, so we must read it from the PF.
Fixes: 90c4f788f6 ("bnxt_en: Report PCIe link speed and width during driver load")
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As a further improvement to the PF/VF link change logic, use a private
mutex instead of the rtnl lock to protect link change logic. With the
new mutex, we don't have to take the rtnl lock in the workqueue when
we have to handle link related functions. If the VF and PF drivers
are running on the same host and both take the rtnl lock and one is
waiting for the other, it will cause timeout. This patch fixes these
timeouts.
Fixes: 90c694bb71 ("bnxt_en: Fix RTNL lock usage on bnxt_update_link().")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Link status query firmware messages originating from the VFs are forwarded
to the PF. The driver handles these interactions in a workqueue for the
VF and PF. The VF driver waits for the response from the PF in the
workqueue. If the PF and VF driver are running on the same host and the
work for both PF and VF are queued on the same workqueue, the VF driver
may not get the response if the PF work item is queued behind it on the
same workqueue. This will lead to the VF link query message timing out.
To prevent this, we create a private workqueue for PFs instead of using
the common workqueue. The VF query and PF response will never be on
the same workqueue.
Fixes: c0c050c58d ("bnxt_en: New Broadcom ethernet driver.")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
40GbE Intel Wired LAN Driver Updates 2017-10-13
This series contains updates to mqprio and i40e.
Amritha introduces a new hardware offload mode in tc/mqprio where the TCs,
the queue configurations and bandwidth rate limits are offloaded to the
hardware. The existing mqprio framework is extended to configure the queue
counts and layout and also added support for rate limiting. This is
achieved through new netlink attributes for the 'mode' option which takes
values such as 'dcb' (default) and 'channel' and a 'shaper' option for
QoS attributes such as bandwidth rate limits in hw mode 1. Legacy devices
can fall back to the existing setup supporting hw mode 1 without these
additional options where only the TCs are offloaded and then the 'mode'
and 'shaper' options defaults to DCB support. The i40e driver enables the
new mqprio hardware offload mechanism factoring the TCs, queue
configuration and bandwidth rates by creating HW channel VSIs.
In this new mode, the priority to traffic class mapping and the user
specified queue ranges are used to configure the traffic class when the
'mode' option is set to 'channel'. This is achieved by creating HW
channels(VSI). A new channel is created for each of the traffic class
configuration offloaded via mqprio framework except for the first TC (TC0)
which is for the main VSI. TC0 for the main VSI is also reconfigured as
per user provided queue parameters. Finally, bandwidth rate limits are set
on these traffic classes through the shaper attribute by sending these
rates in addition to the number of TCs and the queue configurations.
Colin Ian King makes an array of constant values "constant".
Alan fixes and issue where on some firmware versions, we were failing to
actually fill out the phy_types which caused ethtool to not report any
link types. Also hardened against a potentially malicious VF by not
letting the VF to reset itself after requesting to change the number of
queues (via ethtool), let the PF reset the VF to institute the requested
changes.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The break statement for the Macronix case is missing and will
fall through to the Winbond case and re-assign the size setting.
Fix this by adding the missing break statement. Also correctly
indent the return statements.
Detected by CoverityScan, CID#1458020 ("Missing break in switch")
Fixes: 96ac18f14a ("cxgb4: Add support for new flash parts")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Collect SGE, PCIE, PM, UP CIM, MA and HMA dumps.
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Try to access TP indirect registers via firmware first. If this fails,
fallback and access them directly. This ensures that driver and
firmware do not conflict each other while accessing the TP indirect
registers.
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Collect firmware mbox and device logs before collecting the rest of
the hardware dumps to snap the firmware state before the mailbox logs
are updated by other hardware dumps.
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Collect EDC0 and EDC1 memory dump.
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add base to collect dump entities. Collect register dump and
update template header accordingly.
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement operations to set/get dump data via ethtool. Also add
template header that precedes dump data, which helps in decoding
and extracting the dump data.
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Today's -next build encountered an error due to a missing definition of
WARN_ON(), caused by some header reorganization removing an implicit
inclusion of linux/bug.h. Fix this with an explicit inclusion.
Signed-off-by: Mark Brown <broonie@kernel.org>
Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Resources such as FT, QPN HT and mdev resources should be allocated
only by parent netdev. Shared resources are allocated and freed by the
parent interface since the parent is always present and created
before the IPoIB PKEY sub-interface.
Signed-off-by: Alex Vesker <valex@mellanox.com>
Reviewed-by: Erez Shitrit <erezsh@mellanox.com>
Similar to VLAN interfaces child interfaces have limited ethtool
support. In current code the main limitation that does not
allow child interface ethtool configuration is due to shared
resources which are managed by the parent.
Signed-off-by: Alex Vesker <valex@mellanox.com>
Reviewed-by: Erez Shitrit <erezsh@mellanox.com>
Child interface ndos will be called to support child interface
specific behaviour.
ndo_init flow:
-Acquire shared QPN to net-device HT from parent
-Continue with the same flow as parent interface
ndo_open flow:
-Initialize child underlay QP and connect to shared FT
-Create child send TIS
-Open child send channels
Signed-off-by: Alex Vesker <valex@mellanox.com>
Reviewed-by: Erez Shitrit <erezsh@mellanox.com>
Child interface profile will be called to support child interface
specific behaviour. The child code is sparse compared to the parent
since the RX channels are shared between the interfaces.
Creating a septate profile for child and parent will make a smother
code with a better ability for future expansion.
The profile stuct is exposed to the parent using a getter function.
Signed-off-by: Alex Vesker <valex@mellanox.com>
Reviewed-by: Erez Shitrit <erezsh@mellanox.com>
This change is needed for PKEY support, since the RQs are shared
between the child interface and the parent. The parent is responsible
for NAPI and the precessing of RX completions. Using the dqpn in the
completion descriptor we set the corresponding child IPoIB netdevice
on the SKB.
The mapping between the dqpn and the netdevice is done using a HT,
each mlx5 IPoIB interface registers its mapping on creation.
Signed-off-by: Alex Vesker <valex@mellanox.com>
Reviewed-by: Erez Shitrit <erezsh@mellanox.com>
Added a function to set PKEY index to IPoIB device driver using the
already present set_id function. PKEY index is attached to the QP
during state modification.
Signed-off-by: Alex Vesker <valex@mellanox.com>
Reviewed-by: Erez Shitrit <erezsh@mellanox.com>
Previous support allowed connecting only a single QPN to the FT.
Now using a linked list multiple QPNs can be attached to the same FT.
Supporting attaching multiple underlay QPs is required for PKEY
support in which child and parent share the same FT.
The actual attaching/detaching FW commands will be called inside the
function symmetrically.
This change requires a change in IPoIB open and close functions, the
attaching/detaching to/from the FT is done each time we open/close.
Signed-off-by: Alex Vesker <valex@mellanox.com>
Reviewed-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
During the creation of the underlay QP the PKEY index is unknown, the
PKEY index is known only when calling ndo_open.
PKEY index attached to the QP during state modification.
Splitting the functions will also make the code symmetric and more
readable. This split is also required for later PKEY support to be
called with the PKEY index during ndo_open.
Signed-off-by: Alex Vesker <valex@mellanox.com>
Reviewed-by: Erez Shitrit <erezsh@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
PTP code is moved to core section of mlx5 driver in order to share
it between ethernet and infiniband. This movement involves the following
changes:
- Change mlx5e_ prefix to be mlx5_
- Add clock structs to Core
- Add clock object to mlx5_core_dev
- Call Init/Uninit clock from core init/cleanup
- Rename mlx5e_tstamp to be mlx5_clock
Signed-off-by: Feras Daoud <ferasda@mellanox.com>
Signed-off-by: Eitan Rabin <rabin@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
en_clock.c renamed clock.c and moved to lib/ as first step
towards relocating code to core part of the driver to allow
sharing between Ethernet and Infiniband.
Signed-off-by: Feras Daoud <ferasda@mellanox.com>
Signed-off-by: Eitan Rabin <rabin@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Add support for direct packet access in TC, note that because
writing the packet will cause the verifier to generate a csum
fixup prologue we won't be able to offload packet writes from
TC, just yet, only the reads will work.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds ability to write packet contents using pre-validated
packet pointers (direct packet access).
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In direct packet access bound checks are already done, we can
simply dereference the packet pointer.
Verifier/parser logic needs to record pointer type. Note that
although verifier does protect us from CTX vs other pointer
changes we will also want to differentiate between PACKET vs
MAP_VALUE or STACK, so we can add the check already.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move data load into a separate function and separate it from
packet length checks of legacy I/O. This makes the code more
readable and easier to reuse.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sizes of fields in struct xdp_md/xdp_buff and some in sk_buff depend
on target architecture. Take that into account and use struct xdp_buff,
not struct xdp_md.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
eBPF is host-endian specific. Translating both BE and LE eBPF
to the NFP is feasible, but would require quite a bit of indirection.
The fact that I don't have access to any BE hosts that would fit
a 25G/40G/100G NIC is also limiting my ability to test big endian.
For now restrict the offload to little endian hosts only.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement byte swaps with rotations, shifts and byte loads.
Remember to clear upper parts of the 64 bit registers.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Register move operation is encoded as alu no op. This means
that one has to specify number of unused/none parameters to
the emit_alu(). Add a helper.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that we have BPF assemebler support in LLVM 6 we can easily
test all compare instructions (LLVM 4 didn't generate most of them
from C). Fix the compare to immediates and refactor the order
of compare to regs to make sure they both follow the same pattern.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We optimize comparisons to immediate 0 as if (reg.lo | reg.hi).
The early return statement was missing, however, which means we
would generate two comparisons - optimized one followed by a
normal 2x 32 bit compare.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ld_field instruction has the following format in NFP assembler:
ld_field[dst, 1000, src, <<24]
reoder parameters to emit_ld_field_any() to make it closer to
the familiar assembler order.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Flow control must be disabled for AVB enabled queues and TX
AVB queues must be enabled by setting BIT(2) of TXQEN.
Correct this by passing the queue mode to DMA callbacks
and by checking in these functions wether we are in AVB
performing the necessary adjustments.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently we are using all the available fifo size in RQS and
TQS fields. This will not work correctly in multi-queues IP's
because total fifo size must be splitted to the enabled queues.
Correct this by computing the available fifo size per queue and
setting the right value in TQS and RQS fields.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When using 'ethtool -L' on a VF to change number of requested queues
from PF, we shouldn't trust the VF to reset itself after making the
request. Doing it that way opens the door for a potentially malicious
VF to do nasty things to the PF which should never be the case.
This makes it such that after VF makes a successful request, PF will
then reset the VF to institute required changes. Only if the request
fails will PF send a message back to VF letting it know the request was
unsuccessful.
Testing-hints:
There should be no real functional changes. This is simply hardening
against a potentially malicious VF.
Signed-off-by: Alan Brady <alan.brady@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When querying the NVM for supported phy_types, on some firmware
versions, we were failing to actually fill out the phy_types which means
ethtool wouldn't report any link types.
Testing-hints:
Check 'ethtool <iface>' if you have the right (wrong?) firmware.
Without this patch, no link modes will be reported.
Signed-off-by: Alan Brady <alan.brady@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Don't populate const array patterns on the stack, instead make it
static. Makes the object code smaller by over 60 bytes:
Before:
text data bss dec hex filename
1953 496 0 2449 991 i40e_diag.o
After:
text data bss dec hex filename
1798 584 0 2382 94e i40e_diag.o
(gcc 6.3.0, x86-64)
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch enables setting up maximum Tx rates for the traffic
classes in i40e. The maximum rate is offloaded to the hardware through
the mqprio framework by specifying the mode option as 'channel' and
shaper option as 'bw_rlimit' and is configured for the VSI. Configuring
minimum Tx rate limit is not supported in the device. The minimum
usable value for Tx rate is 50Mbps.
Example:
# tc qdisc add dev eth0 root mqprio num_tc 2 map 0 0 0 0 1 1 1 1\
queues 4@0 4@4 hw 1 mode channel shaper bw_rlimit\
max_rate 4Gbit 5Gbit
To dump the bandwidth rates:
# tc qdisc show dev eth0
qdisc mqprio 804a: root tc 2 map 0 0 0 0 1 1 1 1 0 0 0 0 0 0 0 0
queues:(0:3) (4:7)
mode:channel
shaper:bw_rlimit max_rate:4Gbit 5Gbit
Signed-off-by: Amritha Nambiar <amritha.nambiar@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch refactors the BW rate limiting for Tx traffic
on the VF to be reused in the next patch for rate limiting Tx
traffic for the VSIs on the PF as well.
Signed-off-by: Amritha Nambiar <amritha.nambiar@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The i40e driver is modified to enable the new mqprio hardware
offload mode and factor the TCs and queue configuration by
creating channel VSIs. In this mode, the priority to traffic
class mapping and the user specified queue ranges are used
to configure the traffic classes by setting the mode option to
'channel'.
Example:
map 0 0 0 0 1 2 2 3 queues 2@0 2@2 1@4 1@5\
hw 1 mode channel
qdisc mqprio 8038: root tc 4 map 0 0 0 0 1 2 2 3 0 0 0 0 0 0 0 0
queues:(0:1) (2:3) (4:4) (5:5)
mode:channel
shaper:dcb
The HW channels created are removed and all the queue configuration
is set to default when the qdisc is detached from the root of the
device.
This patch also disables setting up channels via ethtool (ethtool -L)
when the TCs are configured using mqprio scheduler.
The patch also limits setting ethtool Rx flow hash indirection
(ethtool -X eth0 equal N) to max queues configured via mqprio.
The Rx flow hash indirection input through ethtool should be
validated so that it is within in the queue range configured via
tc/mqprio. The bound checking is achieved by reporting the current
rss size to the kernel when queues are configured via mqprio.
Example:
map 0 0 0 1 0 2 3 0 queues 2@0 4@2 8@6 11@14\
hw 1 mode channel
Cannot set RX flow hash configuration: Invalid argument
Signed-off-by: Amritha Nambiar <amritha.nambiar@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch sets up the infrastructure for offloading TCs and
queue configurations to the hardware by creating HW channels(VSI).
A new channel is created for each of the traffic class
configuration offloaded via mqprio framework except for the first TC
(TC0). TC0 for the main VSI is also reconfigured as per user provided
queue parameters. Queue counts that are not power-of-2 are handled by
reconfiguring RSS by reprogramming LUTs using the queue count value.
This patch also handles configuring the TX rings for the channels,
setting up the RX queue map for channel.
Also, the channels so created are removed and all the queue
configuration is set to default when the qdisc is detached from the
root of the device.
Signed-off-by: Amritha Nambiar <amritha.nambiar@intel.com>
Signed-off-by: Kiran Patil <kiran.patil@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Introduce a macro for the bit setting the PF reset flag and
update its usages. This makes it easier to use this flag
in functions to be introduced in future without encountering
checkpatch issues related to alignment and line over 80
characters.
Signed-off-by: Amritha Nambiar <amritha.nambiar@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The DMA reset timeout, used in read_poll_timeout, is
ten times shorter than the sleep time.
This patch fixes these values interchanging them, as it was
before the read_poll_timeout introduction.
Fixes: 8a70aeca80 ("net: stmmac: Use readl_poll_timeout")
Signed-off-by: Emiliano Ingrassia <ingrassia@epigenesys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While experimenting with changes to the timekeeping code, I
ran into a build error in the liquidio driver:
drivers/net/ethernet/cavium/liquidio/lio_main.c: In function 'liquidio_ptp_settime':
drivers/net/ethernet/cavium/liquidio/lio_main.c:1850:22: error: passing argument 1 of 'timespec_to_ns' from incompatible pointer type [-Werror=incompatible-pointer-types]
The driver had a type mismatch since it was first merged, but
this never caused problems because it is only built on 64-bit
architectures that define timespec and timespec64 to the same
type.
If we ever want to compile-test the driver on 32-bit or change
the way that 64-bit timespec64 is defined, we need to fix it,
so let's just do it now.
Fixes: f21fb3ed36 ("Add support of Cavium Liquidio ethernet adapters")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Felix Manlunas <felix.manlunas@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The module clock is used for two purposes:
- Wake-on-LAN (WoL), which is optional,
- gPTP Timer Increment (GTI) configuration, which is mandatory.
As the clock is needed for GTI configuration anyway, WoL is always
available. Hence remove duplication and repeated obtaining of the clock
by making GTI use the stored clock for WoL use.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are 4 very similar PHYs:
0x600d84a1: BCM54210E (rev B0)
0x600d84a2: BCM54210E (rev B1)
0x600d84a5: B50212E (rev B0)
0x600d84a6: B50212E (rev B1)
that need setting master mode manually. It's because they run in slave
mode by default with Automatic Slave/Master configuration disabled which
can lead to unreliable connection with massive ping loss.
So far it was reported for a board with BCM47189 SoC and B50212E B1 PHY
connected to the bgmac supported ethernet device. Telling PHY driver to
setup PHY properly solves this issue.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
Delete unused channel variables in vxge-traffic.
Signed-off-by: Christos Gkekas <chris.gekas@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that we have established the queue mapping between the switch port
egress queues and the SYSTEMPORT egress queues, we can turn on Advanced
Congestion Buffering (ACB) at the SYSTEMPORT level. This enables the
Ethernet MAC controller to get out of band flow control information
directly from the switch port and queue that it monitors such that its
internal TDMA can be appropriately backpressured.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Establish a queue mapping between the DSA slave network device queues
created that correspond to switch port queues, and the transmit queue
that SYSTEMPORT manages.
We need to configure the SYSTEMPORT transmit queue with the switch port number
and switch port queue number in order for the switch and SYSTEMPORT hardware to
utilize the out of band congestion notification. This hardware mechanism works
by looking at the switch port egress queue and determines whether there is
enough buffers for this queue, with that class of service for a successful
transmission and if not, backpressures the SYSTEMPORT queue that is being used.
For this to work, we implement a notifier which looks at the
DSA_PORT_REGISTER event. When DSA network devices are registered, the
framework calls the DSA notifiers when that happens, extracts the number
of queues for these devices and their associated port number, remembers
that in the driver private structure and linearly maps those queues to
TX rings/queues that we manage.
This scheme works because DSA slave network deviecs always transmit
through SYSTEMPORT so when DSA slave network devices are
destroyed/brought down, the corresponding SYSTEMPORT queues are no
longer used. Also, by design of the DSA framework, the master network
device (SYSTEMPORT) is registered first.
For faster lookups we use an array of up to DSA_MAX_PORTS * number of
queues per port, and then map pointers to bcm_sysport_tx_ring such that
our ndo_select_queue() implementation can just index into that array to
locate the corresponding ring index.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit df1ec1b9d0.
It turns out that memory allocated via dma_alloc_coherent is always
aligned to the size of the buffer, so there's no way the RRD and RFD
can ever be in separate 32-bit regions.
Signed-off-by: Timur Tabi <timur@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
In XDP_TX, some fields in tx_info and tx_desc are constants across
all entries of the different XDP_TX rings.
Assign values to these fields on ring creation time, rather than in
data-path.
Patchset performance tests:
Tested on ConnectX3Pro, Intel(R) Xeon(R) CPU E5-2680 v3 @ 2.50GHz
Single queue no-RSS optimization ON.
XDP_TX packet rate:
------------------------------
Before | After | Gain |
13.7 Mpps | 14.0 Mpps | %2.2 |
------------------------------
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Function mlx4_en_tx_write_desc() is not optimized to use of XDP xmit.
Use the relevant parts inline instead.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The struct net_device parameter was passed only to extract
struct mlx4_en_priv out of it.
Here we pass the priv parameter directly.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The only user of cls_flower->egress_dev is mlx5. So do the conversion
there alongside with the code originating the call in cls_flower
function fl_hw_replace_filter to the newly introduced egress device
callback infrastucture.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support to bridge two devices which can send multiplexing and
aggregation (MAP) data. This is done only when the data itself is
not going to be consumed in the stack but is being passed on to a
different endpoint. This is mainly used for testing.
Signed-off-by: Subash Abhinov Kasiviswanathan <subashab@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rather than using a static array, use a hlist to store the muxed
endpoints and use the mux id to query the rmnet_device.
This is useful as usually very few mux ids are used.
Signed-off-by: Subash Abhinov Kasiviswanathan <subashab@codeaurora.org>
Cc: Dan Williams <dcbw@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The rmnet_devices information is already stored in muxed_ep, so
storing this in rmnet_devices[] again is redundant.
Signed-off-by: Subash Abhinov Kasiviswanathan <subashab@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The end point is set twice in the local_ep as well as the mux_id and
the real_dev in the rmnet private structure. Remove the local_ep.
While these elements are equivalent, rmnet_endpoint will be
used only as part of the rmnet_port for muxed scenarios in VND mode.
Signed-off-by: Subash Abhinov Kasiviswanathan <subashab@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Mode information on the real device makes it easier to route packets
to rmnet device or bridged device based on the configuration.
Signed-off-by: Subash Abhinov Kasiviswanathan <subashab@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Most of these constants were used in the initial patchset where
custom netlink configuration was used and hence are no longer relevant.
Signed-off-by: Subash Abhinov Kasiviswanathan <subashab@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This will be rewritten in the following patches.
Signed-off-by: Subash Abhinov Kasiviswanathan <subashab@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some of the error messages that are printed by the interrupt handlers
are poorly written. For example, many don't include a device prefix,
so there's no indication that they are EMAC errors.
Also use rate limiting for all messages that could be printed from
interrupt context.
Signed-off-by: Timur Tabi <timur@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The EMAC has a restriction that the upper 32 bits of the base addresses
for the RFD and RRD rings must be the same. The ensure that restriction,
we allocate twice the space for the RRD and locate it at an appropriate
address.
We also re-arrange the allocations so that invalid addresses are even
less likely.
Signed-off-by: Timur Tabi <timur@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The EMAC is capable of multiple TX and RX rings, but the driver only
supports one ring for each. One function had some left-over unused
code that supports multiple rings, but all it did was make the code
harder to read.
Signed-off-by: Timur Tabi <timur@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 64/32-bit DMA mask hackery in the EMAC driver is not actually necessary,
and is technically not accurate. The EMAC hardware is limted to a 45-bit
DMA address. Although no EMAC-enabled system can have that much DDR,
an IOMMU could possible provide a larger address. Rather than play games
with the DMA mappings, the driver should provide a correct value and
trust the DMA/IOMMU layers to do the right thing.
Signed-off-by: Timur Tabi <timur@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
rtl_init_one() currently enables PCI wakeups if the ethernet device
is found to be WOL-capable. There is no need to do this when
rtl8169_set_wol() will correctly enable or disable the same wakeup flag
when WOL is activated/deactivated.
This works around an ACPI DSDT bug which prevents the Acer laptop models
Aspire ES1-533, Aspire ES1-732, PackardBell ENTE69AP and Gateway NE533
from entering S3 suspend - even when no ethernet cable is connected.
On these platforms, the DSDT says that GPE08 is a wakeup source for
ethernet, but this GPE fires as soon as the system goes into suspend,
waking the system up immediately. Having the wakeup normally disabled
avoids this issue in the default case.
With this change, WOL will continue to be unusable on these platforms
(it will instantly wake up if WOL is later enabled by the user) but we
do not expect this to be a commonly used feature on these consumer
laptops. We have separately determined that WOL works fine without any
ACPI GPEs enabled during sleep, so a DSDT fix or override would be
possible to make WOL work.
Signed-off-by: Daniel Drake <drake@endlessm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes the following sparse warnings:
drivers/net/ethernet/hisilicon/hns3/hns3pf/hns3_ethtool.c:464:5: warning:
symbol 'hns3_change_all_ring_bd_num' was not declared. Should it be static?
drivers/net/ethernet/hisilicon/hns3/hns3pf/hns3_ethtool.c:477:5: warning:
symbol 'hns3_set_ringparam' was not declared. Should it be static?
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
1GbE Intel Wired LAN Driver Updates 2017-10-10
This series contains updates to e1000e and igb.
Benjamin Poirier provides several fixes for e1000e, starting with a
correction to the return status which was always returning success even
if it was not successful. Fixed code comments to reflect the actual
code behavior. Fixed the conditional test for the correct return
value. Fixed a potential race condition reported by Lennart Sorensen,
where the single flag get_link_status is used to signal two different
states.
Sasha fixes a buffer overrun for i219 devices, where the chipset had
reduced the round-trip latency for the LAN controller DMA accesses
which in some high performance cases caused a buffer overrun while
processing the DMA transactions.
Willem de Bruijn changes the default behavior of e1000e to use the
burst mode settings by default unless the user specifies the
receive interrupt delay (RxIntDelay).
Florian Fainelli updates the driver to differentiate between when
e1000e_put_txbuf() is called from normal reclamation or when a
DMA mapping failure to make the driver more "drop monitor friendly".
Christophe JAILLET fixes a potential NULL pointer dereference by
properly returning -ENOMEM on memory allocation failures.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
page_address() does not handle NULL argument gracefully,
make sure we NULL-check the page pointer before passing it
to page_address().
Fixes: ecd63a0217 ("nfp: add XDP support in the driver")
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The while loop fetching 64 bit ethtool statistics may have
to retry multiple times, it shouldn't modify the outside state.
Fixes: 4c3523623d ("net: add driver for Netronome NFP4000/NFP6000 NIC VFs")
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove limitation of netif_get_num_default_rss_queues()
from logic of RX rings default number.
Signed-off-by: Inbar Karmy <inbark@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Limit the number of RX rings by the number of cores
in the system.
Signed-off-by: Inbar Karmy <inbark@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Limit the number of TX rings per UP by the number of cores
in the system.
Signed-off-by: Inbar Karmy <inbark@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fix the ring count for ETHTOOL_GRXRINGS. Ring count
not TC size should be return for command "ethtool -n ethx".
Signed-off-by: Lipeng <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch add support for ethtool's ETHTOOL_GRXFH in hns3_get_rxnfc().
Signed-off-by: Lipeng <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for new flash parts identification, and
also cleanup the flash Part identifying and decoding
code.
Based on the original work of Casey Leedom <leedom@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Check memory allocation failures and return -ENOMEM in such cases, as
already done for other memory allocations in this function.
This avoids NULL pointers dereference.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Tested-by: Aaron Brown <aaron.f.brown@intel.com
Acked-by: PJ Waskiewicz <peter.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
e1000e_put_txbuf() can be called from normal reclamation path as well as
when a DMA mapping failure, so we need to differentiate these two cases
when freeing SKBs to be drop monitor friendly. e1000e_tx_hwtstamp_work()
and e1000_remove() are processing TX timestamped SKBs and those should
not be accounted as drops either.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Devices that support FLAG2_DMA_BURST have different default values
for RDTR and RADV. Apply burst mode default settings only when no
explicit value was passed at module load.
The RDTR default is zero. If the module is loaded for low latency
operation with RxIntDelay=0, do not override this value with a burst
default of 32.
Move the decision to apply burst values earlier, where explicitly
initialized module variables can be distinguished from defaults.
Signed-off-by: Willem de Bruijn <willemb@google.com>
Acked-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Intel® 100/200 Series Chipset platforms reduced the round-trip
latency for the LAN Controller DMA accesses, causing in some high
performance cases a buffer overrun while the I219 LAN Connected
Device is processing the DMA transactions. I219LM and I219V devices
can fall into unrecovered Tx hang under very stressfully UDP traffic
and multiple reconnection of Ethernet cable. This Tx hang of the LAN
Controller is only recovered if the system is rebooted. Slightly slow
down DMA access by reducing the number of outstanding requests.
This workaround could have an impact on TCP traffic performance
on the platform. Disabling TSO eliminates performance loss for TCP
traffic without a noticeable impact on CPU performance.
Please, refer to I218/I219 specification update:
https://www.intel.com/content/www/us/en/embedded/products/networking/
ethernet-connection-i218-family-documentation.html
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Reviewed-by: Dima Ruinskiy <dima.ruinskiy@intel.com>
Reviewed-by: Raanan Avargil <raanan.avargil@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When e1000e_poll() is not fast enough to keep up with incoming traffic, the
adapter (when operating in msix mode) raises the Other interrupt to signal
Receiver Overrun.
This is a double problem because 1) at the moment e1000_msix_other()
assumes that it is only called in case of Link Status Change and 2) if the
condition persists, the interrupt is repeatedly raised again in quick
succession.
Ideally we would configure the Other interrupt to not be raised in case of
receiver overrun but this doesn't seem possible on this adapter. Instead,
we handle the first part of the problem by reverting to the practice of
reading ICR in the other interrupt handler, like before commit 16ecba59bc
("e1000e: Do not read ICR in Other interrupt"). Thanks to commit
0a8047ac68 ("e1000e: Fix msi-x interrupt automask") which cleared IAME
from CTRL_EXT, reading ICR doesn't interfere with RxQ0, TxQ0 interrupts
anymore. We handle the second part of the problem by not re-enabling the
Other interrupt right away when there is overrun. Instead, we wait until
traffic subsides, napi polling mode is exited and interrupts are
re-enabled.
Reported-by: Lennart Sorensen <lsorense@csclub.uwaterloo.ca>
Fixes: 16ecba59bc ("e1000e: Do not read ICR in Other interrupt")
Signed-off-by: Benjamin Poirier <bpoirier@suse.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Lennart reported the following race condition:
\ e1000_watchdog_task
\ e1000e_has_link
\ hw->mac.ops.check_for_link() === e1000e_check_for_copper_link
/* link is up */
mac->get_link_status = false;
/* interrupt */
\ e1000_msix_other
hw->mac.get_link_status = true;
link_active = !hw->mac.get_link_status
/* link_active is false, wrongly */
This problem arises because the single flag get_link_status is used to
signal two different states: link status needs checking and link status is
down.
Avoid the problem by using the return value of .check_for_link to signal
the link status to e1000e_has_link().
Reported-by: Lennart Sorensen <lsorense@csclub.uwaterloo.ca>
Signed-off-by: Benjamin Poirier <bpoirier@suse.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
All the helpers return -E1000_ERR_PHY.
Signed-off-by: Benjamin Poirier <bpoirier@suse.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Reading e1000e_check_for_copper_link() shows that get_link_status is set to
false after link has been detected. Therefore, it stays TRUE until then.
Signed-off-by: Benjamin Poirier <bpoirier@suse.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In case of error from e1e_rphy(), the loop will exit early and "success"
will be set to true erroneously.
Signed-off-by: Benjamin Poirier <bpoirier@suse.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
It looks like we weren't correctly placing the pages from buffers that had
been used to return a filter programming status back on the ring. As a
result they were being overwritten and tracking of the pages was lost.
This change works to correct that by incorporating part of
i40e_put_rx_buffer into the programming status handler code. As a result we
should now be correctly placing the pages for those buffers on the
re-allocation list instead of letting them stay in place.
Fixes: 0e626ff7cc ("i40e: Fix support for flow director programming status")
Reported-by: Anders K. Pedersen <akp@cohaesio.com>
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Anders K Pedersen <akp@cohaesio.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Caller needs to acquire the lock. Called functions will not.
Fixes: 09f79fd49d ("i40e: avoid NVM acquire deadlock during NVM update")
Signed-off-by: Stefano Brivio <sbrivio@redhat.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Jeff Kirsher says:
====================
40GbE Intel Wired LAN Driver Updates 2017-10-09
This series contains updates to i40e and i40evf only.
Jake fixes missed flag conversion from u64 to u32. Fixes a deafult ITR
value issue where the driver defaults to an ITR value of half the
expected value (in terms of minimum microseconds between interrupts). So
fix this by changing the default values to be calculated using the
ITR_REG_TO_USEC() macro which indicates that we are converting from the
register units into microseconds. Updates the drivers to bump the tail in
increments of 8 and double the number of descriptors we will bundle into
one tail bump when receiving. With the recent kernel support for
enabling XPS and QoS at the same time, we no longer need to worry about
the number of traffic classes when enabling XPS.
Lihong converts the use of hash_for_each() to hash_for_each_safe() to
safely remove a hash entry. Adds a check for the return value for
find_first_bit() in the case that it returns the size passed to search.
Alan fixes a bug in which filters are erroneously removed if they are
removed and then added again. So make sure that when adding a filter, if
we find it already existed in our list, make sure it is not marked to be
removed.
Jayaprakash adds the retrying of PHY reads when the I2C is busy for a
maximum period of 500ms.
Rami fixes code comment typo.
Stefano Brivio simplifies the code by removing the use of a local
return code variable and simply return the results of the read function.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
10GbE Intel Wired LAN Driver Updates 2017-10-09
This series contains updates to ixgbe only.
Emil fixes an issue where the semaphore bits could be stuck after a reset
or a crash, by adding the clearing of software resource bits in the
software/firmware synchronization register. Added error checks when we
attempt to identify and initialize the PHY to prevent a crash. Fixed a
few issues in the logic of ixgbe_clean_test_rings() which was exposed by
a previous commit that was causing a crash in ethtool diagnostics.
Bhumika Goyal fixes a couple of instances which were overlooked when we
made ixgbe_mac_operations constant.
Shannon Nelson fixes an issue to restore normal operations after the
last MACVLAN offload is removed, otherwise we get stuck in a single queue
operations.
The infamous Jesper Dangaard Brouer adds a counter which counts the
number of times the recycle fails and the real page allocator is invoked.
Alex updates the adaptive ITR algorithm to better support the needs of the
network. This attempt to make it so that our ITR algorithm will try to
prevent either starving a socket buffer for memory in the case of
transmit, or overrunning an receive socket buffer on receive. We should
function better with new features like XDP which can handle small packets
at high rates without needing to lock us into NAPI polling mode.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes a typo in i40e_vsi_alloc_arrays() documentation.
The first parameter name should be "vsi" instead of "type".
Signed-off-by: Rami Rosen <rami.rosen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The computed result of I40E_MAX_VSI_QP * I40E_VIRTCHNL_SUPPORTED_QTYPES
is used more than three times in function i40e_config_irq_link_list.
Simply declare a local variable to store it to improve readability.
Signed-off-by: Lihong Yang <lihong.yang@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
- When the I2C is busy, the PHY reads are delayed. The firmware will
return EGAIN in these cases with an expectation that the SW will
trigger the reads again
- This patch retries the operation for a maximum period of 500ms
Signed-off-by: Jayaprakash Shanmugam <jayaprakash.shanmugam@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The find_first_bit function will return the size passed to search
if the first set bit is not found. This patch adds the check in case
that happens as the return value would be used as the index in an array
and that would have caused the out-of-bounds access.
Detected by CoverityScan, CID 1295969 Out-of-bounds access
Signed-off-by: Lihong Yang <lihong.yang@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Recently, the kernel gained support for enabling XPS and QoS at the
same time. Thus, we no longer need to worry about the number of
traffic classes when enabling XPS.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Double the number of descriptors we'll bundle into one tail bump when
receiving. Empirical testing has shown that we reduce CPU utilization
and don't appear to reduce throughput or packet rate. 32 seems to be the
sweet spot, as it's half the default polling budget, so we'd essentially
reduce from 4 tail writes when polling down to 2. Increasing this up to
64 appears to have negative impacts as it may become possible that we
don't bump the tail each time we get polled, which could cause a long
delay between returning descriptors to the hardware.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Hardware only fetches descriptors on cachelines of 8, essentially
ignoring the lower 3 bits of the tail register. Thus, it is pointless to
bump tail by an unaligned access as the hardware will ignore some of the
new descriptors we allocated. Thus, it's ideal if we can ensure tail
writes are always aligned to 8.
At first, it seems like we'd already do this, since we allocate
descriptors in batches which are a multiple of 8. Since we'd always
increment by a multiple of 8, it seems like the value should always be
aligned.
However, this ignores allocation failures. If we fail to allocate
a buffer, our tail register will become unaligned. Once it has become
unaligned it will essentially be stuck unaligned until a buffer
allocation happens to fail at the exact amount necessary to re-align it.
We can do better, by simply rounding down the number of buffers we're
about to allocate (cleaned_count) such that "next_to_clean
+ cleaned_count" is rounded to the nearest multiple of 8.
We do this by calculating how far off that value is and subtracting it
from the cleaned_count. This essentially defers allocation of buffers if
they're going to be ignored by hardware anyways, and re-aligns our
next_to_use and tail values after a failure to allocate a descriptor.
This calculation ensures that we always align the tail writes in a way
the hardware expects and don't unnecessarily allocate buffers which
won't be fetched immediately.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The lrxq thresh value tells hardware to immediately interrupt when there
are fewer than N*64 packets left in the ring.
Counter intuitively, empirical testing has shown that decreasing this
value from 2 to 1, and thus changing from an immediate interrupt at
fewer than 128 descriptors down to 64 descriptors causes a small
increase in the maximum total packets per second we can receive. This
increase occurs even when we're polling with interrupts masked, as the
hardware must still handle interrupts internally even if we've disabled
them in software.
Also reduce the value for any VFs we allocate.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In the past we changed driver behavior to not clear the PBA when
re-enabling interrupts. This change was motivated by the flawed belief
that clearing the PBA would cause a lost interrupt if a receive
interrupt occurred while interrupts were disabled.
According to empirical testing this isn't the case. Additionally, the
data sheet specifically says that we should set the CLEARPBA bit when
re-enabling interrupts in a polling setup.
This reverts commit 40d72a5098 ("i40e/i40evf: don't lose interrupts")
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The ITR register expects to be programmed in units of 2 microseconds.
Because of this, all of the drivers I40E_ITR_* constants are in terms of
this 2 microsecond register.
Unfortunately, the rx_itr_default value is expected to be programmed in
microseconds.
Effectively the driver defaults to an ITR value of half the expected
value (in terms of minimum microseconds between interrupts).
Fix this by changing the default values to be calculated using
ITR_REG_TO_USEC macro which indicates that we're converting from the
register units into microseconds.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Due to the asynchronous nature in which mac filters are added and
deleted, there exists a bug in which filters are erroneously removed if
removed then added again quickly.
The events are as such:
- filter marked for removal
- same filter is re-added before watchdog that cleans up filters
- we skip re-adding the filter because we have it already in the
list
- watchdog filter cleanup kicks off and filter is removed
So when we were re-adding the same filter, it didn't actually get added
because it already existed in the list, but was marked for removal and
had yet to actually be removed.
This patch fixes the issue by making sure that when adding a filter, if
we find it already existing in our list, make sure it is not marked to
be removed.
Signed-off-by: Alan Brady <alan.brady@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch replaces hash_for_each function with hash_for_each_safe
when calling __i40e_del_filter. The hash_for_each_safe function is
the right one to use when iterating over a hash table to safely remove
a hash entry. Otherwise, incorrect values may be read from freed memory.
Detected by CoverityScan, CID 1402048 Read from pointer after free
Signed-off-by: Lihong Yang <lihong.yang@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Since we don't yet have more than 32 flags, we'll use a u32 for both the
hw_features and flag field. Should we gain more flags in the future, we
may need to convert to a u64 or separate flags out into two fields.
This was overlooked in the previous commit 2781de2134c4 ("i40e/i40evf:
organize and re-number feature flags"), where the feature flag was not
converted form u64 to u32.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Cc: Sunil Goutham <sgoutham@cavium.com>
Cc: Robert Richter <rric@kernel.org>
Cc: linux-arm-kernel@lists.infradead.org
Cc: netdev@vger.kernel.org
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In TX data-path, we intentionally do not byte-swap, as documented
in code and in the cited commit log.
This fixes sparse warning:
en_tx.c:720:23: warning: incorrect type in argument 1 (different base types)
en_tx.c:720:23: expected unsigned int [unsigned] [usertype] <noident>
en_tx.c:720:23: got restricted __be32 [usertype] doorbell_qpn
Fixes: 492f5add4b ("net/mlx4_en: Doorbell is byteswapped in Little Endian archs")
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the following SPARSE warning, in MLX4_GET() macro:
drivers/net/ethernet/mellanox/mlx4/fw.c:233:9: warning: cast to restricted __be64
Fixes: 17d5ceb6e4 ("net/mlx4_core: Fix unaligned accesses")
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Should take care of the endianness before assigning to params2 field.
Fixes: 53f33ae295 ("net/mlx4_core: Port aggregation upper layer interface")
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We continue to maintain a maximum of three buffers per fpdu, to ensure
that there are enough buffers for additional unaligned mpa packets.
To support this, if a fpdu is split over more than two tcp packets, we
use an intermediate buffer to copy the data to the previous buffer, then
we can release the data. We need an intermediate buffer as the initial
buffer partial packet could be located at the end of the packet, not
leaving room for additional data. This is a corner case, and will usually
not be the case.
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a special case where an MPA header is split over to tcp
packets, in this case we need to wait for the next packet to
get the fpdu length. We use the incomplete_bytes to mark this
fpdu as a "special" one which requires updating the length with
the next packet
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When posting a packet on the ll2 tx, we can provide a cookie that
will be returned upon tx completion. This cookie is the ll2 iwarp buffer
which is then reposted to the rx ring. Part of the unaligned mpa flow
is determining when a buffer can be reposted. Each buffer needs to be
sent only once as a cookie for on the tx ring. In packed fpdu case, only
the last packet will be sent with the buffer, meaning we need to handle the
case that a cookie can be NULL on tx complete. In addition, when a fpdu
splits over two buffers, but there are no more fpdus on the second buffer,
two buffers need to be provided as a cookie. To avoid changing the ll2
interface to provide two cookies, we introduce a piggy buf pointer,
relevant for iWARP only, that holds a pointer to a second buffer that
needs to be released during tx completion.
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The fpdu data structure is preallocated per connection.
Each connection stores the current status of the connection:
either nothing pending, or there is a partial fpdu that is waiting for
the rest of the fpdu (incomplete bytes != 0).
The same structure is also used for splitting a packet when there are
packed fpdus. The structure is initialized with all data required
for sending the fpdu back to the FW. A fpdu will always be spanned across
a maximum of 3 tx bds. One for the header, one for the partial fdpu
received and one for the remainder (unaligned) packet.
In case of packed fpdu's, two fragments are used, one for the header
and one for the data.
Corner cases are not handled in the patch for clarity, and will be added
as a separate patch.
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mpa buff is a descriptor for iwarp ll2 buffers that contains
additional information required for aligining fpdu's.
In some cases, an additional packet will arrive which will complete
the alignment of a fpdu, but we won't be able to post the fpdu due to
insufficient place on the tx ring. In this case we can't loose the data
and require storing it for later. Processing is therefore done
in two places, during rx completion, where we initialize a mpa buffer
descriptor and add it to the pending list, and during tx-completion, since
we free up an entry in the tx chain we can process any pending mpa packets.
The mpa buff descriptors are pre-allocated since we have to ensure that
we won't reach a state where we can't store an incoming unaligned packet.
All packets received on the ll2 MUST be processed by the driver at some
stage. Since they are preallocated, we hold a free list.
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds only the establishment and termination of the
ll2 connection that handles unaligned MPA packets.
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For iWARP unaligned MPA flow, a slowpath event of flushing an
MPA connection that entered an unaligned state is required.
The flush ramrod is received on the ll2 queue, and a pre-registered
callback function is called to handle the flush event.
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a packet is sent back to iWARP FW via the tx ll2 connection
the FW needs to know the source of the packet. Whether it is
OOO or unaligned MPA related. Since OOO is implemented entirely
inside the ll2 code (and shared with iSCSI), packets are marked
as IN_ORDER inside the ll2 code. For unaligned mpa the value
will be determined in the iWARP code and sent on the pkt->vlan
field.
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
enable_ip_cksum, enable_l4_cksum, calc_ip_len were added in
commit stated below but not passed through to FW. This was OK
until now as it wasn't used, but is required for the iWARP
unaligned flow
Fixes:7c7973b2ae27 ("qed: LL2 to use packed information for tx")
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The option of sending a packet on the ll2 and dropping it exists in
hardware and was not used until now, thus not exposed.
The iWARP unaligned MPA flow requires this functionality for
flushing the tx queue.
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When more than one ll2 queue is opened ( that is not an OOO queue )
ll2 code does not have enough information to determine whether
the queue is the main one or not, so a new field is added to the
acquire input data to expose the control of determining whether
the queue is the main queue or a secondary queue.
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
iWARP uses 3 ll2 connections, the maximum number of bds is known
during connection setup. This patch modifies the static array in
the ll2_tx_packet descriptor to be a flexible array and
significantlly reduces memory size.
In addition, some redundant fields in the ll2_tx_packet were
removed, which also contributed to decreasing the descriptor size.
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Support the SWITCHDEV_ATTR_ID_BRIDGE_MROUTER port attribute switchdev
notification.
To do that, add the mrouter flag to struct mlxsw_sp_bridge_device, which
indicates whether the bridge device was set to be mrouter port. This field
is set when:
- A new bridge is created, where the value is taken from the kernel
bridge value.
- A switchdev SWITCHDEV_ATTR_ID_BRIDGE_MROUTER notification is sent.
In addition, change the bridge MID entries to include the router port when
the bridge device is configured to be mrouter port. The MID entries are
updated in the following cases:
- When a new MID entry is created, update the router port according to the
bridge mrouter state.
- When a SWITCHDEV_ATTR_ID_BRIDGE_MROUTER notification is sent, update all
the bridge's MID entries.
This is aligned with the case where a bridge slave is configured to be
mrouter port.
Signed-off-by: Yotam Gigi <yotamg@mellanox.com>
Reviewed-by: Nogah Frankel <nogahf@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In Spectrum, MDB entries point to MID entries, that indicate which ports a
packet should be forwarded to. Add the support in creating MID entries that
forward the packet to the Spectrum router port.
This will be later used to handle the bridge mrouter port switchdev
notifications.
Signed-off-by: Yotam Gigi <yotamg@mellanox.com>
Reviewed-by: Nogah Frankel <nogahf@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In Spectrum hardware, the router port is a virtual port that is the gateway
to the routing mechanism. Hence, in order for a packet to be L3 forwarded,
it must first be L2 forwarded to the router port inside the hardware.
Further patches in this patchset are going to introduce support in bridge
device used as an mrouter port. In this case, the router port index will be
needed in order to update the MDB entries to include the router port. Thus,
export the mlxsw_sp_router_port function, which returns the index of the
Spectrum router port.
Signed-off-by: Yotam Gigi <yotamg@mellanox.com>
Reviewed-by: Nogah Frankel <nogahf@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case where AER recovery fails the device is left in a down state.
Consecutive AER error injection can lead to a double IRQ free.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The following change is meant to update the adaptive ITR algorithm to
better support the needs of the network. Specifically with this change what
I have done is make it so that our ITR algorithm will try to prevent either
starving a socket buffer for memory in the case of Tx, or overrunning an Rx
socket buffer on receive.
In addition a side effect of the calculations used is that we should
function better with new features such as XDP which can handle small
packets at high rates without needing to lock us into NAPI polling mode.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Bits other than FWSM.PT can be set in IXGBE_SWFW_MODE_MASK making the
previous check invalid.
Change the check for MNG present to be only based on FWSM.PT bit.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch is resolving Coverity hits where padding in a structure could
be used uninitialized.
- Initialize fwd_cmd.pad/2 before ixgbe_calculate_checksum()
- Initialize buffer.pad2/3 before ixgbe_hic_unlocked()
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The ixgbe driver have page recycle scheme based around the RX-ring
queue, where a RX page is shared between two packets. Based on the
refcnt, the driver can determine if the RX-page is currently only used
by a single packet, if so it can then directly refill/recycle the
RX-slot by with the opposite "side" of the page.
While this is a clever trick, it is hard to determine when this
recycling is successful and when it fails. Adding a counter, which is
available via ethtool --statistics as 'alloc_rx_page'. Which counts
the number of times the recycle fails and the real page allocator is
invoked. When interpreting the stats, do remember that every alloc
will serve two packets.
The counter is collected per rx_ring, but is summed and ethtool
exported as 'alloc_rx_page'. It would be relevant to know what
rx_ring that cannot keep up, but that can be exported later if
someone experience a need for this.
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
ld_field instruction is a bit special because the encoding uses
two source registers and one of them becomes the output. We do
need to pass the dst register to our encoding helpers though,
otherwise the "write both banks" flag will not be observed.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Device expects the instructions in little endian. Make sure we
byte swap on big endian hosts.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
