Pull ARM SoC fixes from Olof Johansson:
"A couple of late-arriving fixes before final 4.13:
- A few reverts of DT bindings on Allwinner for their ethernet
driver. Discussion didn't converge, and since bindings are
considered ABI it makes sense to revert instead of having to
support two bindings long-term.
- A fix to enumerate GPIOs properly on Marvell Armada AP806"
* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
arm64: dts: marvell: fix number of GPIOs in Armada AP806 description
arm: dts: sunxi: Revert EMAC changes
arm64: dts: allwinner: Revert EMAC changes
dt-bindings: net: Revert sun8i dwmac binding
mvebu fixes for 4.13 (part 3)
Fix number of GPIOs in AP806 description for Armada 7K/8K
* tag 'mvebu-fixes-4.13-3' of git://git.infradead.org/linux-mvebu:
arm64: dts: marvell: fix number of GPIOs in Armada AP806 description
Signed-off-by: Olof Johansson <olof@lixom.net>
Allwinner fixes for 4.13, take 3
This is a revert of the EMAC bindings. The discussion has not settled down
yet on a proper representation of the PHY, and therefore we cannot commit
to a binding yet
* tag 'sunxi-fixes-for-4.13-3' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
arm: dts: sunxi: Revert EMAC changes
arm64: dts: allwinner: Revert EMAC changes
dt-bindings: net: Revert sun8i dwmac binding
Signed-off-by: Olof Johansson <olof@lixom.net>
Since the discussion is not settled yet for the EMAC, and that the release
in getting really close, let's revert the changes for now, and we'll
reintroduce them later.
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
With 16KB pages and a kernel Image larger than 16MB, the current
kaslr_early_init() logic for avoiding mappings across swapper table
boundaries fails since increasing the offset by kimg_sz just moves the
problem to the next boundary.
This patch rounds the offset down to (1 << SWAPPER_TABLE_SHIFT) if the
Image crosses a PMD_SIZE boundary.
Fixes: afd0e5a876 ("arm64: kaslr: Fix up the kernel image alignment")
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Neeraj Upadhyay <neeraju@codeaurora.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
In the KASLR setup routine, we ensure that the early virtual mapping
of the kernel image does not cover more than a single table entry at
the level above the swapper block level, so that the assembler routines
involved in setting up this mapping can remain simple.
In this calculation we add the proposed KASLR offset to the values of
the _text and _end markers, and reject it if they would end up falling
in different swapper table sized windows.
However, when taking the addresses of _text and _end, the modulo offset
(the physical displacement modulo 2 MB) is already accounted for, and
so adding it again results in incorrect results. So disregard the modulo
offset from the calculation.
Fixes: 08cdac619c ("arm64: relocatable: deal with physically misaligned ...")
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Tested-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
When there's a fatal signal pending, arm64's do_page_fault()
implementation returns 0. The intent is that we'll return to the
faulting userspace instruction, delivering the signal on the way.
However, if we take a fatal signal during fixing up a uaccess, this
results in a return to the faulting kernel instruction, which will be
instantly retried, resulting in the same fault being taken forever. As
the task never reaches userspace, the signal is not delivered, and the
task is left unkillable. While the task is stuck in this state, it can
inhibit the forward progress of the system.
To avoid this, we must ensure that when a fatal signal is pending, we
apply any necessary fixup for a faulting kernel instruction. Thus we
will return to an error path, and it is up to that code to make forward
progress towards delivering the fatal signal.
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Laura Abbott <labbott@redhat.com>
Cc: stable@vger.kernel.org
Reviewed-by: Steve Capper <steve.capper@arm.com>
Tested-by: Steve Capper <steve.capper@arm.com>
Reviewed-by: James Morse <james.morse@arm.com>
Tested-by: James Morse <james.morse@arm.com>
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
There are some tricky dependencies between the different stages of
flushing the FPSIMD register state during exec, and these can race
with context switch in ways that can cause the old task's regs to
leak across. In particular, a context switch during the memset() can
cause some of the task's old FPSIMD registers to reappear.
Disabling preemption for this small window would be no big deal for
performance: preemption is already disabled for similar scenarios
like updating the FPSIMD registers in sigreturn.
So, instead of rearranging things in ways that might swap existing
subtle bugs for new ones, this patch just disables preemption
around the FPSIMD state flushing so that races of this type can't
occur here. This brings fpsimd_flush_thread() into line with other
code paths.
Cc: stable@vger.kernel.org
Fixes: 674c242c93 ("arm64: flush FP/SIMD state correctly after execve()")
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Dave Martin <Dave.Martin@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Pull timer fixes from Thomas Gleixner:
"A few small fixes for timer drivers:
- Prevent infinite recursion in the arm architected timer driver with
ftrace
- Propagate error codes to the caller in case of failure in EM STI
driver
- Adjust a bogus loop iteration in the arm architected timer driver
- Add a missing Kconfig dependency to the pistachio clocksource to
prevent build failures
- Correctly check for IS_ERR() instead of NULL in the shared timer-of
code"
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
clocksource/drivers/arm_arch_timer: Avoid infinite recursion when ftrace is enabled
clocksource/drivers/Kconfig: Fix CLKSRC_PISTACHIO dependencies
clocksource/drivers/timer-of: Checking for IS_ERR() instead of NULL
clocksource/drivers/em_sti: Fix error return codes in em_sti_probe()
clocksource/drivers/arm_arch_timer: Fix mem frame loop initialization
Moving the x86_64 and arm64 PIE base from 0x555555554000 to 0x000100000000
broke AddressSanitizer. This is a partial revert of:
eab09532d4 ("binfmt_elf: use ELF_ET_DYN_BASE only for PIE")
02445990a9 ("arm64: move ELF_ET_DYN_BASE to 4GB / 4MB")
The AddressSanitizer tool has hard-coded expectations about where
executable mappings are loaded.
The motivation for changing the PIE base in the above commits was to
avoid the Stack-Clash CVEs that allowed executable mappings to get too
close to heap and stack. This was mainly a problem on 32-bit, but the
64-bit bases were moved too, in an effort to proactively protect those
systems (proofs of concept do exist that show 64-bit collisions, but
other recent changes to fix stack accounting and setuid behaviors will
minimize the impact).
The new 32-bit PIE base is fine for ASan (since it matches the ET_EXEC
base), so only the 64-bit PIE base needs to be reverted to let x86 and
arm64 ASan binaries run again. Future changes to the 64-bit PIE base on
these architectures can be made optional once a more dynamic method for
dealing with AddressSanitizer is found. (e.g. always loading PIE into
the mmap region for marked binaries.)
Link: http://lkml.kernel.org/r/20170807201542.GA21271@beast
Fixes: eab09532d4 ("binfmt_elf: use ELF_ET_DYN_BASE only for PIE")
Fixes: 02445990a9 ("arm64: move ELF_ET_DYN_BASE to 4GB / 4MB")
Signed-off-by: Kees Cook <keescook@chromium.org>
Reported-by: Kostya Serebryany <kcc@google.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull "Allwinner fixes for 4.13, round 2" from Chen-Yu Tsai:
Three fixes adding a missing alias for the Ethernet controller on A64
boards. One adding a missing interrupt for the pin controller.
* tag 'sunxi-fixes-for-4.13-2' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
arm64: allwinner: h5: fix pinctrl IRQs
arm64: allwinner: a64: sopine: add missing ethernet0 alias
arm64: allwinner: a64: pine64: add missing ethernet0 alias
arm64: allwinner: a64: bananapi-m64: add missing ethernet0 alias
Pull "Fourth Round of Renesas ARM Based SoC Fixes for v4.13" from Simon Horman:
* Avoid audio_clkout naming conflict for salvator boards using
Renesas R-Car Gen 3 SoCs
Morimoto-san says "The clock name of "audio_clkout" is used by the
Renesas sound driver. This duplicated naming breaks its clock
registering/unregistering. Especially when unbind/bind it can't handle
clkout correctly. This patch renames "audio_clkout" to "audio-clkout" to
avoid the naming conflict."
* tag 'renesas-fixes4-for-v4.13' of https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
arm64: renesas: salvator-common: avoid audio_clkout naming conflict
The pin controller of H5 has three IRQs at the chip's GIC, which
represents three banks of pinctrl IRQs. However, the device tree used to
miss the third IRQ of the pin controller, which makes the PG bank IRQ
not usable.
Add the missing IRQ to the pinctrl node.
Fixes: 4e36de179f ("arm64: allwinner: h5: add Allwinner H5 .dtsi")
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Pull clockevents fixes from Daniel Lezcano:
" - Fix error check against IS_ERR() instead of NULL for the timer-of code (Dan Carpenter)
- Fix infinite recusion with ftrace for the ARM architected timer (Ding Tianhong)
- Fix the error code return in the em_sti's probe function (Gustavo A. R. Silva)
- Fix Kconfig dependency for the pistachio driver (Matt Redfearn)
- Fix mem frame loop initialization for the ARM architected timer (Matthias Kaehlcke)"
Signed-off-by: Ingo Molnar <mingo@kernel.org>
On platforms with an arch timer erratum workaround, it's possible for
arch_timer_reg_read_stable() to recurse into itself when certain
tracing options are enabled, leading to stack overflows and related
problems.
For example, when PREEMPT_TRACER and FUNCTION_GRAPH_TRACER are
selected, it's possible to trigger this with:
$ mount -t debugfs nodev /sys/kernel/debug/
$ echo function_graph > /sys/kernel/debug/tracing/current_tracer
The problem is that in such cases, preempt_disable() instrumentation
attempts to acquire a timestamp via trace_clock(), resulting in a call
back to arch_timer_reg_read_stable(), and hence recursion.
This patch changes arch_timer_reg_read_stable() to use
preempt_{disable,enable}_notrace(), which avoids this.
This problem is similar to the fixed by upstream commit 96b3d28bf4
("sched/clock: Prevent tracing recursion in sched_clock_cpu()").
Fixes: 6acc71ccac ("arm64: arch_timer: Allows a CPU-specific erratum to only affect a subset of CPUs")
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
The EMAC Ethernet controller was enabled, but an accompanying alias
was not added. This results in unstable numbering if other Ethernet
devices, such as a USB dongle, are present. Also, the bootloader uses
the alias to assign a generated stable MAC address to the device node.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Fixes: 96219b0048 ("arm64: allwinner: a64: add device tree for SoPine
with baseboard")
[wens@csie.org: Rewrite commit log as fixing a previous patch with Fixes]
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
The EMAC Ethernet controller was enabled, but an accompanying alias
was not added. This results in unstable numbering if other Ethernet
devices, such as a USB dongle, are present. Also, the bootloader uses
the alias to assign a generated stable MAC address to the device node.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Fixes: 9702394374 ("arm64: allwinner: pine64: Enable dwmac-sun8i")
[wens@csie.org: Rewrite commit log as fixing a previous patch with Fixes]
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
The EMAC Ethernet controller was enabled, but an accompanying alias
was not added. This results in unstable numbering if other Ethernet
devices, such as a USB dongle, are present. Also, the bootloader uses
the alias to assign a generated stable MAC address to the device node.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Fixes: e729549990 ("arm64: allwinner: bananapi-m64: Enable dwmac-sun8i")
[wens@csie.org: Rewrite commit log as fixing a previous patch with Fixes]
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
clock name of "audio_clkout" is used by Renesas sound driver.
This duplicated naming breaks its clock registering/unregistering.
Especially, when unbind/bind it can't handle clkout correctly.
This patch renames "audio_clkout" to "audio-clkout" to avoid
naming conflict.
Fixes: 8a8f181d2c ("arm64: renesas: salvator-x: use CS2000 as AUDIO_CLK_B")
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Pull KVM fixes from Radim Krčmář:
"ARM:
- Yet another race with VM destruction plugged
- A set of small vgic fixes
x86:
- Preserve pending INIT
- RCU fixes in paravirtual async pf, VM teardown, and VMXOFF
emulation
- nVMX interrupt injection and dirty tracking fixes
- initialize to make UBSAN happy"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: arm/arm64: vgic: Use READ_ONCE fo cmpxchg
KVM: nVMX: Fix interrupt window request with "Acknowledge interrupt on exit"
KVM: nVMX: mark vmcs12 pages dirty on L2 exit
kvm: nVMX: don't flush VMCS12 during VMXOFF or VCPU teardown
KVM: nVMX: do not pin the VMCS12
KVM: avoid using rcu_dereference_protected
KVM: X86: init irq->level in kvm_pv_kick_cpu_op
KVM: X86: Fix loss of pending INIT due to race
KVM: async_pf: make rcu irq exit if not triggered from idle task
KVM: nVMX: fixes to nested virt interrupt injection
KVM: nVMX: do not fill vm_exit_intr_error_code in prepare_vmcs12
KVM: arm/arm64: Handle hva aging while destroying the vm
KVM: arm/arm64: PMU: Fix overflow interrupt injection
KVM: arm/arm64: Fix bug in advertising KVM_CAP_MSI_DEVID capability
Pull ARM SoC fixes from Arnd Bergmann:
"This comes a bit later than I planned, and as a consequence is a
larger than it should be.
Most of the changes are devicetree fixes, across lots of platforms:
Renesas, Samsung Exynos, Marvell EBU, TI OMAP, Rockchips, Amlogic
Meson, Sigma Desings Tango, Allwinner SUNxi and TI Davinci.
Also across many platforms, I applied an older series of simple
randconfig build fixes. This includes making the CONFIG_MTD_XIP option
compile again, which had been broken for many years and probably has
not been missed, but it felt wrong to just remove it completely.
The only other changes are:
- We enable HWSPINLOCK in defconfig to get some Qualcomm boards to
work out of the box.
- A few regression fixes for Texas Instruments OMAP2+.
- A boot regression fix for the Renesas regulator quirk.
- A suspend/resume fix for Uniphier SoCs, fixing the resume of the
system bus"
* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (43 commits)
ARM: dts: tango4: Request RGMII RX and TX clock delays
bus: uniphier-system-bus: set up registers when resuming
ARM64: dts: marvell: armada-37xx: Fix the number of GPIO on south bridge
ARM: shmobile: rcar-gen2: Fix deadlock in regulator quirk
arm64: defconfig: enable missing HWSPINLOCK
ARM: pxa: select both FB and FB_W100 for eseries
ARM: ixp4xx: fix ioport_unmap definition
ARM: ep93xx: use ARM_PATCH_PHYS_VIRT correctly
ARM: mmp: mark usb_dma_mask as __maybe_unused
ARM: omap2: mark unused functions as __maybe_unused
ARM: omap1: avoid unused variable warning
ARM: sirf: mark sirfsoc_init_late as __maybe_unused
ARM: ixp4xx: use normal prototype for {read,write}s{b,w,l}
ARM: omap1/ams-delta: warn about failed regulator enable
ARM: rpc: rename RAM_SIZE macro
ARM: w90x900: normalize clk API
ARM: ep93xx: normalize clk API
ARM: dts: sun8i: a83t: Switch to CCU device tree binding macros
arm64: allwinner: sun50i-a64: Correct emac register size
ARM: dts: sunxi: h3/h5: Correct emac register size
...
The bitmask used to define these values produces overflow, as seen by
this compiler warning:
arch/arm64/kernel/head.S:47:8: warning:
integer overflow in preprocessor expression
#elif (PAGE_OFFSET & 0x1fffff) != 0
^~~~~~~~~~~
arch/arm64/include/asm/memory.h:52:46: note:
expanded from macro 'PAGE_OFFSET'
#define PAGE_OFFSET (UL(0xffffffffffffffff) << (VA_BITS -
1))
~~~~~~~~~~~~~~~~~~ ^
It would be preferrable to use GENMASK_ULL() instead, but it's not set
up to be used from assembly (the UL() macro token pastes UL suffixes
when not included in assembly sources).
Suggested-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Suggested-by: Yury Norov <ynorov@caviumnetworks.com>
Suggested-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
In a system with DBM (dirty bit management) capable agents there is a
possible race between a CPU executing ptep_set_access_flags() (maybe
non-DBM capable) and a hardware update of the dirty state (clearing of
PTE_RDONLY). The scenario:
a) the pte is writable (PTE_WRITE set), clean (PTE_RDONLY set) and old
(PTE_AF clear)
b) ptep_set_access_flags() is called as a result of a read access and it
needs to set the pte to writable, clean and young (PTE_AF set)
c) a DBM-capable agent, as a result of a different write access, is
marking the entry as young (setting PTE_AF) and dirty (clearing
PTE_RDONLY)
The current ptep_set_access_flags() implementation would set the
PTE_RDONLY bit in the resulting value overriding the DBM update and
losing the dirty state.
This patch fixes such race by setting PTE_RDONLY to the most permissive
(lowest value) of the current entry and the new one.
Fixes: 66dbd6e61a ("arm64: Implement ptep_set_access_flags() for hardware AF/DBM")
Cc: Will Deacon <will.deacon@arm.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Steve Capper <steve.capper@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Pull "Allwinner fixes for 4.13" from Chen-Yu Tsai:
Two fixes to correct the EMAC blocks memory region size to match the
datasheet. One that converts raw A83T clock indices to macros from the
clk dt-binding header, completing the A83T sunxi-ng clk driver.
* tag 'sunxi-fixes-for-4.13' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
ARM: dts: sun8i: a83t: Switch to CCU device tree binding macros
arm64: allwinner: sun50i-a64: Correct emac register size
ARM: dts: sunxi: h3/h5: Correct emac register size
Pull "Qualcomm ARM64 based defconfig Fixes for v4.13-rc2" from Andy Gross:
* Enable missing HWSPINLOCK
* tag 'qcom-arm64-defconfig-fixes-for-4.13-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/agross/linux:
arm64: defconfig: enable missing HWSPINLOCK
Pull "mvebu fixes for 4.13 (part 2)" from Gregory CLEMENT:
All the fixes are for ARM64 mvebu:
- Fix the RTC interrupt on A7K/A8K which was missed when switching
from GIC to ICU
- Mark the A7K/A8K crypto engine as dma coherent
- Fix the number of GPIO on south bridge on Armada 3700
* tag 'mvebu-fixes-4.13-2' of git://git.infradead.org/linux-mvebu:
ARM64: dts: marvell: armada-37xx: Fix the number of GPIO on south bridge
arm64: dts: marvell: mark the cp110 crypto engine as dma coherent
arm64: dts: marvell: use ICU for the CP110 slave RTC
Pull "Amlogic fixes for v4.13-rc" from Kevin Hilman:
- 2 minor DT fixes
* tag 'amlogic-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic:
ARM64: dts: meson-gxl-s905x-libretech-cc: fixup board definition
ARM64: dts: meson-gx: use specific compatible for the AO pwms
The number of pins in South Bridge is 30 and not 29. There is a fix for
the driver for the pinctrl, but a fix is also need at device tree level
for the GPIO.
Fixes: afda007fed ("ARM64: dts: marvell: Add pinctrl nodes for Armada
3700")
Cc: <stable@vger.kernel.org>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
In an ideal world, CNTFRQ_EL0 always contains the timer frequency
for the kernel to use. Sadly, we get quite a few broken systems
where the firmware authors cannot be bothered to program that
register on all CPUs, and rely on DT to provide that frequency.
So when trapping CNTFRQ_EL0, make sure to return the actual rate
(as known by the kernel), and not CNTFRQ_EL0.
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Pull arm64 fixes from Will Deacon:
"I'd been collecting these whilst we debugged a CPU hotplug failure,
but we ended up diagnosing that one to tglx, who has taken a fix via
the -tip tree separately.
We're seeing some NFS issues that we haven't gotten to the bottom of
yet, and we've uncovered some issues with our backtracing too so there
might be another fixes pull before we're done.
Summary:
- Ensure we have a guard page after the kernel image in vmalloc
- Fix incorrect prefetch stride in copy_page
- Ensure irqs are disabled in die()
- Fix for event group validation in QCOM L2 PMU driver
- Fix requesting of PMU IRQs on AMD Seattle
- Minor cleanups and fixes"
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: mmu: Place guard page after mapping of kernel image
drivers/perf: arm_pmu: Request PMU SPIs with IRQF_PER_CPU
arm64: sysreg: Fix unprotected macro argmuent in write_sysreg
perf: qcom_l2: fix column exclusion check
arm64/lib: copy_page: use consistent prefetch stride
arm64/numa: Drop duplicate message
perf: Convert to using %pOF instead of full_name
arm64: Convert to using %pOF instead of full_name
arm64: traps: disable irq in die()
arm64: atomics: Remove '&' from '+&' asm constraint in lse atomics
arm64: uaccess: Remove redundant __force from addr cast in __range_ok
The vast majority of virtual allocations in the vmalloc region are followed
by a guard page, which can help to avoid overruning on vma into another,
which may map a read-sensitive device.
This patch adds a guard page to the end of the kernel image mapping (i.e.
following the data/bss segments).
Cc: Mark Rutland <mark.rutland@arm.com>
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
The hardware spinlock drivers now depend on HWSPINLOCK (instead of
selecting it), so we need to explicitly enable it after commit
35fc8a07d7 ("Make HWSPINLOCK a menuconfig to ease disabling")
Without HWSPINLOCK, various drivers are left with unsatisfied
dependencies and Qcom boards using shared memory based communication
to request regulators are failing to boot and mount rootfs.
Fix this by explicitly enabling HWSPINLOCK in defconfig.
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
The datasheet said that emac register size is 0x10000 not 0x100
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
[wens@csie.org: Fixed commit subject prefix]
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Pull "Second Round of Renesas ARM Based SoC Fixes for v4.13" from Simon Horman:
Correct order of sound clock frequencies for ULCB boards
used by r8a7795 and r8a7796 SoCs.
These sounds clock frequencies are used as the ADG clock (output clocks
for audio module) initial setting and sound codec's initial system clock
which needs the maximum clock frequency. Thus, descending order is
required.
* tag 'renesas-fixes2-for-v4.13' of https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
arm64: dts: renesas: ulcb: sound clock-frequency needs descending order
Pull "Renesas ARM Based SoC Fixes for v4.13" from Simon Horman:
Correct order of sound clock frequencies for Salvator boards
used by r8a7795 and r8a7796 SoCs.
These sounds clock frequencies are used as the ADG clock (output clocks
for audio module) initial setting and sound codec's initial system clock
which needs the maximum clock frequency. Thus, descending order is
required.
* tag 'renesas-fixes-for-v4.13' of https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
arm64: renesas: salvator-common: sound clock-frequency needs descending order
write_sysreg() may misparse the value argument because it is used
without parentheses to protect it.
This patch adds the ( ) in order to avoid any surprises.
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Dave Martin <Dave.Martin@arm.com>
[will: same change to write_sysreg_s]
Signed-off-by: Will Deacon <will.deacon@arm.com>
Pull dma mapping fixes from Christoph Hellwig:
"split the global dma coherent pool from the per-device pool.
This fixes a regression in the earlier 4.13 pull requests where the
global pool would override a per-device CMA pool (Vladimir Murzin)"
* tag 'dma-mapping-4.13-2' of git://git.infradead.org/users/hch/dma-mapping:
ARM: NOMMU: Wire-up default DMA interface
dma-coherent: introduce interface for default DMA pool
kvm_pmu_overflow_set() is called from perf's interrupt handler,
making the call of kvm_vgic_inject_irq() from it introduced with
"KVM: arm/arm64: PMU: remove request-less vcpu kick" a really bad
idea, as it's quite easy to try and retake a lock that the
interrupted context is already holding. The fix is to use a vcpu
kick, leaving the interrupt injection to kvm_pmu_sync_hwstate(),
like it was doing before the refactoring. We don't just revert,
though, because before the kick was request-less, leaving the vcpu
exposed to the request-less vcpu kick race, and also because the
kick was used unnecessarily from register access handlers.
Reviewed-by: Christoffer Dall <cdall@linaro.org>
Signed-off-by: Andrew Jones <drjones@redhat.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
The optional prefetch instructions in the copy_page() routine are
inconsistent: at the start of the function, two cachelines are
prefetched beyond the one being loaded in the first iteration, but
in the loop, the prefetch is one more line ahead. This appears to
be unintentional, so let's fix it.
While at it, fix the comment style and white space.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Pull core fixes from Ingo Molnar:
"A fix to WARN_ON_ONCE() done by modules, plus a MAINTAINERS update"
* 'core-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
debug: Fix WARN_ON_ONCE() for modules
MAINTAINERS: Update the PTRACE entry
The libretech CC derives less from the p212 than initially thought.
Several voltage regulators are different and the capabilities of the
sdcard and emmc also differ.
Deriving from the p212 is not convient anymore so the libretech is now
derived from s905x definition directly.
Fixes: cd84aff1d9 ("ARM64: dts: meson-gxl: Add Libre Technology CC support")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Use the specific compatible for AO pwms so the pwms input can
be correctly set
FDIV4 is not present on the pwm A0, so change kadhas vim input
clocks to xtal.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Christoph noticed [1] that default DMA pool in current form overload
the DMA coherent infrastructure. In reply, Robin suggested [2] to
split the per-device vs. global pool interfaces, so allocation/release
from default DMA pool is driven by dma ops implementation.
This patch implements Robin's idea and provide interface to
allocate/release/mmap the default (aka global) DMA pool.
To make it clear that existing *_from_coherent routines work on
per-device pool rename them to *_from_dev_coherent.
[1] https://lkml.org/lkml/2017/7/7/370
[2] https://lkml.org/lkml/2017/7/7/431
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Suggested-by: Robin Murphy <robin.murphy@arm.com>
Tested-by: Andras Szemzo <sza@esh.hu>
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Vladimir Murzin <vladimir.murzin@arm.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Mike Galbraith reported a situation where a WARN_ON_ONCE() call in DRM
code turned into an oops. As it turns out, WARN_ON_ONCE() seems to be
completely broken when called from a module.
The bug was introduced with the following commit:
19d436268d ("debug: Add _ONCE() logic to report_bug()")
That commit changed WARN_ON_ONCE() to move its 'once' logic into the bug
trap handler. It requires a writable bug table so that the BUGFLAG_DONE
bit can be written to the flags to indicate the first warning has
occurred.
The bug table was made writable for vmlinux, which relies on
vmlinux.lds.S and vmlinux.lds.h for laying out the sections. However,
it wasn't made writable for modules, which rely on the ELF section
header flags.
Reported-by: Mike Galbraith <efault@gmx.de>
Tested-by: Masami Hiramatsu <mhiramat@kernel.org>
Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Fixes: 19d436268d ("debug: Add _ONCE() logic to report_bug()")
Link: http://lkml.kernel.org/r/a53b04235a65478dd9afc51f5b329fdc65c84364.1500095401.git.jpoimboe@redhat.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
In current die(), the irq is disabled for __die() handle, not
including the possible panic() handling. Since the log in __die()
can take several hundreds ms, new irq might come and interrupt
current die().
If the process calling die() holds some critical resource, and some
other process scheduled later also needs it, then it would deadlock.
The first panic will not be executed.
So here disable irq for the whole flow of die().
Signed-off-by: Qiao Zhou <qiaozhou@asrmicro.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
