This patch adds the whole GMAC4 support inside the
stmmac d.d. now able to use the new HW and some new features
i.e.: TSO.
It is missing the multi-queue and split Header support at this
stage.
This patch also updates the driver version and the stmmac.txt.
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is the initial support for GMAC4 that includes
the main callbacks to setup the core module: including
Csum, basic filtering, mac address and interrupt (MMC,
MTL, PMT) No LPI added.
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
DMA behavior is linked to descriptor management:
-descriptor mechanism (Tx for example, but it is exactly the same for RX):
-useful registers:
-DMA_CH#_TxDesc_Ring_Len: length of transmit descriptor ring
-DMA_CH#_TxDesc_List_Address: start address of the ring
-DMA_CH#_TxDesc_Tail_Pointer: address of the last
descriptor to send + 1.
-DMA_CH#_TxDesc_Current_App_TxDesc: address of the current
descriptor
-The descriptor Tail Pointer register contains the pointer to the
descriptor address (N). The base address and the current
descriptor decide the address of the current descriptor that the
DMA can process. The descriptors up to one location less than the
one indicated by the descriptor tail pointer (N-1) are owned by
the DMA. The DMA continues to process the descriptors until the
following condition occurs:
"current descriptor pointer == Descriptor Tail pointer"
Then the DMA goes into suspend mode. The application must perform
a write to descriptor tail pointer register and update the tail
pointer to have the following condition and to start a new transfer:
"current descriptor pointer < Descriptor tail pointer"
The DMA automatically wraps around the base address when the end
of ring is reached.
Up to 8 DMA could be use but currently we only use one (channel0)
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
One of main changes of GMAC 4.xx IP is descriptors management.
-descriptors are only used in ring mode.
-A descriptor is composed of 4 32bits registers (no more extended
descriptors)
-descriptor mechanism (Tx for example, but it is exactly the same for RX):
-useful registers:
-DMA_CH#_TxDesc_Ring_Len: length of transmit descriptor
ring
-DMA_CH#_TxDesc_List_Address: start address of the ring
-DMA_CH#_TxDesc_Tail_Pointer: address of the last
descriptor to send + 1.
-DMA_CH#_TxDesc_Current_App_TxDesc: address of the current
descriptor
-The descriptor Tail Pointer register contains the pointer to the
descriptor address (N). The base address and the current
descriptor decide the address of the current descriptor that the
DMA can process. The descriptors up to one location less than the
one indicated by the descriptor tail pointer (N-1) are owned by
the DMA. The DMA continues to process the descriptors until the
following condition occurs:
"current descriptor pointer == Descriptor Tail pointer"
Then the DMA goes into suspend mode. The application must perform
a write to descriptor tail pointer register and update the tail
pointer to have the following condition and to start a new
transfer:
"current descriptor pointer < Descriptor tail pointer"
The DMA automatically wraps around the base address when the end
of ring is reached.
-New features are available on IP:
-TSO (TCP Segmentation Offload) for TX only
-Split header: to have header and payload in 2 different buffers
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
synopsys_uid is only used once after setup, to get synopsys_id
by using shitf/mask operation. It's no longer used then.
So, remove this temporary variable and directly compute
synopsys_id from setup routine.
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To avoid lot of check in stmmac_main for display ring management
and support the GMAC4 chip, the display_ring function is moved
into dedicated descriptor file.
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On next GMAC IP generation (4.xx), the way to get hw feature
is not the same than on previous 3.xx. As it is hardware
dependent, the way to get hw capabilities should be defined in dma ops of
each MAC IP. It will avoid also a huge computation of hw capabilities in
stmmac_main.
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is to fill the first descriptor just before granting
the DMA engine so at the end of the xmit.
The patch takes care about the algorithm adopted to mitigate the
interrupts, then it fixes the last segment in case of no fragments.
Moreover, this new implementation does not pass any "ter" field when
prepare the descriptors because this is not necessary.
The patch also details the memory barrier in the xmit.
As final results, this patch guarantees the same performances
but fixing a case if small datagram are sent. In fact, this
kind of test is impacted if no coalesce is done.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch "inline" get_tx_owner and get_ls routines. It Results in a
unique read to tdes0, instead of three, to check TX_OWN and LS bits,
and other status bits.
It helps improve driver TX path by removing two uncached read/writes
inside TX clean loop for enhanced descriptors but not for normal ones
because the des1 must be read in any case.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is to optimize the way to manage the TDES inside the
xmit function. When prepare the frame, some settings (e.g. OWN
bit) can be merged. This has been reworked to improve the tx
performances.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The RDES0 register can be read several times while doing RX of a
packet.
This patch slightly improves RX path performance by reading rdes0
once for two operation: check rx owner, get rx status bits.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is to rework the ring management now optimized.
The indexes into the ring buffer are always incremented, and
the entry is accessed via doing a modulo to find the "real"
position in the ring.
It is inefficient, modulo is an expensive operation.
The formula [(entry + 1) & (size - 1)] is now adopted on
a ring that is power-of-2 in size.
Then, the number of elements cannot be set by command line but
it is fixed.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch restructures the DMA bus settings and this is done
by introducing a new platform structure used for programming
the AXI Bus Mode Register inside the DMA module.
This structure can be populated from device-tree as documented in the
binding txt file.
After initializing the DMA, the AXI register can be optionally tuned
for platform drivers based.
This patch also reworks some parameters to make coherent the DMA
configuration now that AXI register is introduced.
For example, the burst_len is managed by using the mentioned axi
support above; so the snps,burst-len parameter has been removed.
It makes sense to provide the AAL parameter from DT to Address-Aligned
Beats inside the Register0 and review the PBL settings when initialize
the engine.
For PCI glue, rebuilding the story of this setting, it
was added to align a configuration so not for fixing some
known problem. No issue raised after this patch.
It is safe to use the default burst length instead of
tuning it to the maximum value
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is to share the same reset procedure between dwmac100 and
dwmac1000 chips.
This will also help on enhancing the driver and support new chips.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
stmmac_config_sub_second_increment set the sub second increment to 20ns.
Driver is configured to use the fine adjustment method where the sub second
register is incremented when the acculumator incremented by the addend
register wraps overflows. This accumulator is update on every ptp clk
cycle. If a ptp clk with a period of greater than 20ns was used the
sub second register would not get updated correctly.
Instead set the sub sec increment to twice the period of the ptp clk.
This result in the addend register being set mid range and overflow
the accumlator every 2 clock cycles.
Signed-off-by: Phil Reid <preid@electromag.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
For GMAC newer than 3.40a there is a new register (Reg_9) that provides the
status of all modules of the transmit and receive paths and FIFO status.
These can be exposed via ethtool.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Configure flow control correctly, and based on the receive fifo size read
as a property from the devicetree since the Synopsys stmmac fifo sizes are
configurable based on a particular chip's implementation. This patch maintains
the previous incorrect behavior unless the receive fifo size is found in the
devicetree.
Signed-off-by: Vince Bridgers <vbridger@opensource.altera.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds some useful comments inside the common header
file to provide information about the APIs exposed by the driver.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes the following sparse warnings.
drivers/net/ethernet/stmicro/stmmac/enh_desc.c:381:30: warning: symbol 'enh_desc_ops' was not declared. Should it be static?
drivers/net/ethernet/stmicro/stmmac/norm_desc.c:253:30: warning: symbol 'ndesc_ops' was not declared. Should it be static?
drivers/net/ethernet/stmicro/stmmac/stmmac_hwtstamp.c:141:33: warning: symbol 'stmmac_ptp' was not declared. Should it be static?
There is no functional change.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Giuseppe CAVALLARO <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For new GMACs it is possible to turn-on/off the COE.
In the current driver, when disabled the Rx-checksum
via ethtool, the tool reported that csum was disabled
but the HW continued to set the IPC. Indeed this is
because the fix_features allows this. So the patch
fixes this problem by adding the set_features.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The value for LPI TW timer has to be updated to 0x1E that is the hardcoded value
of 20.5us and it will apply to all EEE enabled Remote PHYs.
Disadvantage is for PHY's that support lesser wakeup time but we can accept it
waiting to implement LLDP to negotiate the Wakeup time of Remote PHY.
Signed-off-by: nandini sharma <nandini.sharma@st.com>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is to fix the definition of macros for EEE otherwise the LPI TX/RX
entry/exit cannot be properly managed.
Signed-off-by: Nandini Sharma <nandini.sharma@st.com>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Enabling DMA_API_DEBUG, warnings are reported at runtime
because the device driver frees DMA memory with wrong functions
and it does not call dma_mapping_error after mapping dma memory.
The first problem is fixed by of introducing a flag that helps us
keeping track which mapping technique was used, so that we can use
the right API for unmap.
This approach was inspired by the e1000 driver, which uses a similar
technique.
Signed-off-by: Andre Draszik <andre.draszik@st.com>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Reviewed-by: Denis Kirjanov <kda@linux-powerpc.org>
Cc: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds and modifies code to support multiple Multicast and Unicast
Synopsys MAC filter configurations. The default configuration is defined to
support legacy driver behavior, which is 64 Multicast bins. The Unicast
filter code previously assumed all controllers support 32 or 16 Unicast
addresses based on controller version number, but this has been corrected
to support a default of 1 Unicast address. The filter configuration may
be specified through the devicetree using a Synopsys specific device tree
entry. This information was verified with Synopsys through
Synopsys Support Case #8000684337 and shared with the maintainer.
Signed-off-by: Vince Bridgers <vbridgers2013@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes the check for the number of mulitcast addresses
when using hash based filtering since it's not necessary. If the number
of multicast addresses in the list exceeds the number of multicast hash
bins, the bins will "fold" over into one of the bins configured and
enabled for the particular component instance.
The default number of maximum unicast addresses was changed from 32 to 1
since this number is not dependent on the component revision. The maximum
number of multicast and unicast addresses is dependent on the configuration
of the Synopsys EMAC configured by the SOC architect at the time the
features were selected and configured for a particular component. Sadly,
Synopsys does not provide a way to query the precise number supported
by a particular component, so we must fall back on a devicetree entry.
This configuration could vary from vendor to vendor (such as STMicro,
Altera, etc).
The multicast bins are set for every possible filtering case (including
no entries) - previously the bits were set only if multicast filter entries
were present.
Signed-off-by: Vince Bridgers <vbridgers2013@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The synopsys EMAC can be configured for different numbers of multicast hash
bins and perfect filter entries at device creation time and there's no way
to query this configuration information at runtime. As a result, a devicetree
parameter is required in order for the driver to program these filters
correctly for a particular device instance. This patch modifies the
10/100/1000 MAC software interface such that these configuration parameters
can be set at initialization time.
Signed-off-by: Vince Bridgers <vbridgers2013@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is to fix the chain mode that was broken
and generated a panic. This patch reviews the chain/ring
modes now shaing the same structure and taking care
about the pointers and callbacks.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
None of these files are actually using any __init type directives
and hence don't need to include <linux/init.h>. Most are just a
left over from __devinit and __cpuinit removal, or simply due to
code getting copied from one driver to the next.
This covers everything under drivers/net except for wireless, which
has been submitted separately.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are a mix of function prototypes with and without extern
in the kernel sources. Standardize on not using extern for
function prototypes.
Function prototypes don't need to be written with extern.
extern is assumed by the compiler. Its use is as unnecessary as
using auto to declare automatic/local variables in a block.
Signed-off-by: Joe Perches <joe@perches.com>
Conflicts:
drivers/net/ethernet/freescale/fec_main.c
drivers/net/ethernet/renesas/sh_eth.c
net/ipv4/gre.c
The GRE conflict is between a bug fix (kfree_skb --> kfree_skb_list)
and the splitting of the gre.c code into seperate files.
The FEC conflict was two sets of changes adding ethtool support code
in an "!CONFIG_M5272" CPP protected block.
Finally the sh_eth.c conflict was between one commit add bits set
in the .eesr_err_check mask whilst another commit removed the
.tx_error_check member and assignments.
Signed-off-by: David S. Miller <davem@davemloft.net>
Prior this patch, the internal debugging was based on ifdef
and also some printk were useless because many info are exposed
via ethtool.
This patch remove all the ifdef defines and now we only use
netif_msg_XXX levels.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes the EEE setup allowing to configure this support
when the link changes.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch tidies up the code. I have run Linden (and verified with checkpatch)
many part of the driver trying to reorganize some sections respecting the
codying-style rules in the points where it was not done.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch implements PHC (ptp hardware clock) driver for stmmac
driver to support 1588 PTP.
V2: added support for FINE method, reduced loop delay and review spinlock.
Signed-off-by: Rayagond Kokatanur <rayagond@vayavyalabs.com>
Hacked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch enhances the stmmac driver to support IEEE 1588-2002
PTP (Precision Time Protocol) version 1 and IEEE 1588-2008 PPT
version 2.
Precision Time Protocol(PTP),which enables precise synchronization
of clocks in measurement and control systems implemented with
technologies such as network communication,local computing,
& distributed objects.
Both PTPv1 and PTPv2 is selected at run-time using the HW capability
register.
The PTPv1 TimeStamp support can be used on chips that have the normal
descriptor structures and PTPv2 TimeStamp support can be used on chips
that have the Extended descriptors(DES4-5-6-7). All such sanity checks
are done and verified by using HW capability register.
V2: in this version the ethtool support has been included in this patch;
Koptions have been completely removed (previously added to select
PTP and PTPv2). PTPv1 and PTPv2 is now added in a single patch instead of
two patches.
get_timestamp() and get_systemtime() L/H have been combined into single APIs.
Signed-off-by: Rayagond Kokatanur <rayagond@vayavyalabs.com>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the minimal support to manage the PCS
modes (RGMII/SGMII) and restart the ANE.
Both TBI and RTBI are not yet supported.
Thanks to Byungho that wrote some part of this code
and tested SGMII too.
The only thing to be fixed is the get/set pause in
ethtool.
Signed-off-by: Byungho An <bh74.an@samsung.com>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch starts adding in the main ISR the management of the PCS and
RGMII/SGMII core interrupts. This is to help further development
on this area. Currently the core irq handler only clears the
PCS and S-R_MII interrupts and reports the event in the ethtool stats.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Tested-by: Byungho An <bh74.an@samsung.com>
Cc: Udit Kumar <udit-dlh.kumar@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is to support the extend descriptors available
in the chips newer than the 3.50.
In case of the extend descriptors cannot be supported,
at runtime, the driver will continue to work using the old style.
In detail, this support extends the main descriptor structure
adding new descriptors: 4, 5, 6, 7. The desc4 gives us extra
information about the received ethernet payload when it is
carrying PTP packets or TCP/UDP/ICMP over IP packets.
The descriptors 6 and 7 are used for saving HW L/H timestamps (PTP).
V2: this new version removes the Koption added in the first implementation
because all the checks now to verify if the extended descriptors are
actually supported happen at probe time.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Previously we had two Koptions to decide if the stmmac
had to use either a ring or a chain to manage its descriptors.
This patch removes the Kernel configuration options and it allow us
to use the chain mode by passing a module option.
Ring mode continues to be the default.
Also with this patch, it will be easier to validate the driver built and
guarantee that all the two modes always compile fine.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
GMAC devices newer than databook 3.40 has an embedded timer
that can be used for mitigating the number of interrupts.
So this patch adds this optimizations.
At any rate, the Rx watchdog can be disable (on bugged HW) by
passing from the platform the riwt_off field.
In this implementation the rx timer stored in the Reg9 is fixed
to the max value. This will be tuned by using ethtool.
V2: added a platform parameter to force to disable the rx-watchdog
for example on new core where it is bugged.
V3: do not disable NAPI when Rx watchdog is used.
V4: a new extra statistic field has been added to show the early
receive status in the interrupt handler.
This patch also adds an extra check to avoid to call
napi_schedule when the DMA_INTR_ENA_RIE bit is disabled in the
Interrupt Mask register.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a new schema used for mitigating the
number of transmit interrupts.
It is based on a SW timer and a threshold value.
The timer is used to periodically call the stmmac_tx_clean
function; the threshold is used for setting the IC (Interrupt
on Completion bit). The ISR will then invoke the poll method.
Also the patch improves some ethtool stat fields.
V2: review the logic to manage the IC bit in the TDESC
that was bugged because it didn't take care about the
fragments. Also fix the tx_count_frames that has not to be
limited to TX DMA ring. Thanks to Ben Hutchings.
V3: removed the spin_lock irqsave/restore as D. Miller suggested.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds "#ifndef __<header>_H" for protecting header from double
inclusion.
Signed-off-by: Rayagond Kokatanur <rayagond@vayavyalabs.com>
Hacked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the Energy Efficient Ethernet support to the stmmac.
Please see the driver's documentation for further details about this support
in the driver.
Thanks also goes to Rayagond Kokatanur for his first implementation.
Note:
to clearly manage and expose the lpi interrupt status and eee ethtool
stats I've had to do some modifications to the driver's design and I
found really useful to move other parts of the code (e.g. mmc irq stat)
in the main directly. So this means that some core has been reworked
to introduce the EEE.
v1: initial patch
v2: fixed some sparse issues (typos)
v3: erroneously sent the v2 renamed as v3
v4:
o Fixed the return value of the stmmac_eee_init as suggested by D.Miller
o Totally reviewed the ethtool support for EEE
o Added a new internal parameter to tune the SW timer for TX LPI.
v5: do not change any eee setting in case of the stmmac_ethtool_op_set_eee fails
(it has to return -EOPNOTSUPP in that case).
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In mixed burst (MB) mode, the AHB master always initiates
the bursts with fixed-size when the DMA requests transfers
of size less than or equal to 16 beats.
This patch adds the MB support and the flag that can be
passed from the platform to select it.
MB mode can also give some benefits in terms of performances
on some platforms.
v2: fixed Coding Style
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is to extend the number of MAC address registers
for 16 to 32. In fact, other new 16 registers are available in new
chips and this can help on perfect filter mode for unicast.
This patch also fixes the perfect filtering mode by setting the
bit 31 in the MAC address registers.
v2: fixed Coding Style.
Signed-off-by: Gianni Antoniazzi <gianni.antoniazzi-ext@st.com>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Recently the dma parameters that can be passed from the platform
have been moved from the plat_stmmacenet_data to the stmmac_dma_cfg.
In case of this new structure is not well allocated the driver can
fails. This is an example how this field is managed in ST platforms
static struct stmmac_dma_cfg gmac_dma_setting = {
.pbl = 32,
};
static struct plat_stmmacenet_data stih415_ethernet_platform_data[] = {
{
.dma_cfg = &gmac_dma_setting,
.has_gmac = 1,
[snip]
This patch so verifies that the dma_cfg passed from the platform.
In case of it is NULL there is no reason that the driver has to fail
and some default values can be passed. These are ok for all the
Synopsys chips and could impact on performances, only.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
cc: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If a specific clk_csr value is passed from the platform
this means that the CSR Clock Range selection cannot be
changed at run-time and it is fixed (as reported in the driver
documentation). Viceversa the driver will try to set the MDC
clock dynamically according to the actual clock input.
Signed-off-by: Deepak Sikri <deepak.sikri@st.com>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Reviewed-by: Francesco Virlinzi <francesco.virlinzi@st.com>
Reviewed-by: David Laight <david.laight@aculab.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch re-works the internal GMAC DMA parameters
passed from the platform.
In the past, we only passed the pbl but, with new core,
other parameters can be passed and are mandatory on some
platforms.
New parameters are documented in stmmac.txt because this
patch has an impact for many platforms.
Signed-off-by: Shiraz Hashim <shiraz.hashim@st.com>
Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
Signed-off-by: Deepak Sikri <deepak.sikri@st.com>
Hacked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch sanities the RX coe and adds the Type-1 Rx checksum offload engine (COE).
So the RX COE can be passed through the platform but can be fixed
at run-time in case of the core has the HW capability register.
Also to support the Type-1 Rx COE the driver must append the
HW checksum at the end of payload in case the Rx checksum
engine was used to offload the HW checksum.
This v2 version also fixes the IPC that has to be enabled and verified.
Signed-off-by: Deepak Sikri <deepak.sikri@st.com>
Hacked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
