No functional change. Reorder header file in alphabetical order.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
commit 025dd3daed ("PCI: keystone: Add error IRQ
handler") added dev_err() message only for ERR_AXI and ERR_FATAL. Add
debug error message for ERR_SYS, ERR_NONFATAL, ERR_CORR and ERR_AER here.
While at that avoid using ERR_IRQ_STATUS_RAW and use ERR_IRQ_STATUS
instead.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Use ERR_IRQ_STATUS instead of ERR_IRQ_STATUS_RAW to get interrupt
status. ERR_IRQ_STATUS_RAW has the status of the interrupts
before masking whereas ERR_IRQ_STATUS has the status of the interrupts
after masking. Since all the interrupts are unmasked here, use
ERR_IRQ_STATUS.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
ks_pcie_link_up() uses registers from the designware core to get the
status of the link. Move the register defines to pcie-designware.h
and cleanup ks_pcie_link_up().
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
No functional change. Use BIT() macro for DBI_CS2 and cleanup
set_dbi_mode() and get_dbi_mode().
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Outbound translation window is configured in order to access the
PCIe card's MEM space. Cleanup outbound translation configuration
here by using BIT() macros, adding a macro for window size and
using lower_32_bits/upper_32_bits macros for configuring the 64 bit
offset in the outbound translation region.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Instead of having a fixed outbound window count, get the number of
outbound windows from the device tree.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cleanup configuration space access by removing ks_pcie_cfg_setup()
which has an unncessary check of "if (bus == 0)" which will never be the
case of *_other_conf() and adding macros for configuring the CFG_SETUP
register required for accessing the configuration space of the device.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Invoke runtime PM APIs to enable clocks and remove explicit
clock enabling using clk_prepare_enable().
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cleanup PHY handling by using devm_phy_optional_get() to get PHYs if
the PHYs are optional, creating a device link between the PHY device
and the controller device and disable PHY on error cases here.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Control module registers should be read using syscon APIs.
pci-keystone.c uses platform_get_resource() to get control module registers.
Fix it here by using syscon APIs to get device id from control module.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
No functional change. Some function names begin with ks_dw_pcie_*
and some function names begin with ks_pcie_*. Modify it so that
all function names begin with ks_pcie_*.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
No functional change. Remove redundant platform_set_drvdata() invocation
in ks_pcie_probe().
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
No functional change. Having two different files for keystone PCI driver
doesn't serve any purpose. Merge pci-keystone-dw.c and pci-keystone.c
into a single pci-keystone.c file and remove pci-keystone.h.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
No functional change. Remove unused "msi_intc_np" argument from
ks_dw_pcie_host_init().
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
commit 886bc5ceb5 ("PCI: designware: Add generic
dw_pcie_wait_for_link()") while adding a generic dw_pcie_wait_for_link()
performed a special handling (initiate link training multiple times) for
keystone which is not required. This also resulted in unncessarily waiting
for more time to establish the link even when no PCI device is connected.
Remove it and make it look similar to other dwc based PCIe drivers.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
No functional change. Move dw_pcie_setup_rc() out of
ks_pcie_establish_link() so that ks_pcie_establish_linki() can be used only
to start the link.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reuse the already existing quirk to set MRRS for PCI host bridge
instead of explicitly setting MRRS in ks_pcie_host_init().
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
PCI controller in K2G also has a limitation that memory read request
size (MRRS) must not exceed 256 bytes. Use the quirk to limit MRRS
(added for K2HK, K2L and K2E) for K2G as well.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
commit 101c92dc80 ("PCI: mediatek: Set up vendor ID and class
type for MT7622") erroneously set the class type for MT7622 to
PCI_CLASS_BRIDGE_HOST.
The PCIe controller of MT7622 integrates a Root Port that has type 1
configuration space header and related bridge windows.
The HW default value of this bridge's class type is invalid.
Fix its class type and set it to PCI_CLASS_BRIDGE_PCI to
match the hardware implementation.
Fixes: 101c92dc80 ("PCI: mediatek: Set up vendor ID and class type for MT7622")
Signed-off-by: Honghui Zhang <honghui.zhang@mediatek.com>
[lorenzo.pieralisi@arm.com: reworked the commit log]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Ryder Lee <ryder.lee@mediatek.com>
The Mediatek's host controller has two slots, each with its own control
registers. The host driver needs to identify what slot is connected to
what port in order to access the device's configuration space.
Current code retrieving slot connected to a given endpoint device.
Assuming each slot is connected to one endpoint device as below:
host bridge
bus 0 --> __________|_______
| |
| |
slot 0 slot 1
bus 1 -->| bus 2 --> |
| |
EP 0 EP 1
During PCI enumeration, system software will scan all the PCI devices on
every bus starting from devfn 0. Using PCI_SLOT(devfn) for matching an
endpoint to its slot is erroneous in that the devfn does not contain the
hierarchical bus numbering in it. In order to match an endpoint with its
slot (and related port), the PCI tree must be walked up to the root bus
(where the root ports are situated) and then the PCI_SLOT(devfn)
matching logic can be correctly applied for matching.
This patch fixes the mtk_pcie_find_port() slot matching logic by adding
appropriate PCI tree walking code to retrieve the slot/port a given
endpoint is connected to.
Signed-off-by: Honghui Zhang <honghui.zhang@mediatek.com>
[lorenzo.pieralisi@arm.com: rewrote the commit log]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Ryder Lee <ryder.lee@mediatek.com>
Currently, eeh_pe_state_mark() marks a PE (and it's children) with a
state and then performs additional processing if that state included
EEH_PE_ISOLATED.
The state parameter is always a constant at the call site, so
rearrange eeh_pe_state_mark() into two functions and just call the
appropriate one at each site.
Signed-off-by: Sam Bobroff <sbobroff@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
According to the PCIe specification, although the MSI data is only
16bits, the upper 16bits should be written as 0. Use writel
instead of writew when writing the MSI data to the host.
Fixes: 37dddf14f1 ("PCI: cadence: Add EndPoint Controller driver for Cadence PCIe controller")
Signed-off-by: Alan Douglas <adouglas@cadence.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
The IRQ physical address is allocated from region 0, rather than
the highest region. Update the driver to reserve this region in
the bitmap and to use region 0 for all types of interrupt.
This corrects a problem which prevents the interrupt being
signalled correctly if using the first address in the AXI region,
since an offset of zero will always be mapped to region 0.
Fixes: 37dddf14f1 ("PCI: cadence: Add EndPoint Controller driver for Cadence PCIe controller")
Signed-off-by: Alan Douglas <adouglas@cadence.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
iov.c uses nothing declared in <linux/pci-ats.h>, so remove the include of
it. No functional change intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cache the config space size from VF0 and use it for all other VFs instead
of reading it from the config space of each VF. We assume that it will be
the same across all associated VFs.
This is an optimization when enabling SR-IOV on a device with many VFs.
Signed-off-by: KarimAllah Ahmed <karahmed@amazon.de>
[bhelgaas: use CONFIG_PCI_IOV (not CONFIG_PCI_ATS)]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Currently the Switchtec quirk runs on all endpoints in the switch,
including all the upstream and downstream ports. These other functions do
not contain BARs, so the quirk fails when trying to map the BAR and prints
the error "Cannot iomap Switchtec device". The user will see a few of
these useless and scary errors, one for each port in the switch.
At most, the quirk should only run on either a management endpoint
(PCI_CLASS_MEMORY_OTHER) or an NTB endpoint (PCI_CLASS_BRIDGE_OTHER).
However, the quirk is useless except in NTB applications, so we will
only run it when the class is PCI_CLASS_BRIDGE_OTHER.
Switch to using DECLARE_PCI_FIXUP_CLASS_FINAL and only match
PCI_CLASS_BRIDGE_OTHER.
Reported-by: Stephen Bates <sbates@raithlin.com>
Fixes: ad281ecf1c ("PCI: Add DMA alias quirk for Microsemi Switchtec NTB")
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
[bhelgaas: split SWITCHTEC_QUIRK() introduction to separate patch]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Doug Meyer <dmeyer@gigaio.com>
Cc: Kurt Schwemmer <kurt.schwemmer@microsemi.com>
Add SWITCHTEC_QUIRK() to reduce redundancy in declaring devices that use
quirk_switchtec_ntb_dma_alias().
By itself, this is no functional change, but a subsequent patch updates
SWITCHTEC_QUIRK() to fix ad281ecf1c ("PCI: Add DMA alias quirk for
Microsemi Switchtec NTB").
Fixes: ad281ecf1c ("PCI: Add DMA alias quirk for Microsemi Switchtec NTB")
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
[bhelgaas: split to separate patch]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Add Device IDs to the Intel GPU "spurious interrupt" quirk table.
For these devices, unplugging the VGA cable and plugging it in again causes
spurious interrupts from the IGD. Linux eventually disables the interrupt,
but of course that disables any other devices sharing the interrupt.
The theory is that this is a VGA BIOS defect: it should have disabled the
IGD interrupt but failed to do so.
See f67fd55fa9 ("PCI: Add quirk for still enabled interrupts on Intel
Sandy Bridge GPUs") and 7c82126a94 ("PCI: Add new ID for Intel GPU
"spurious interrupt" quirk") for some history.
[bhelgaas: See link below for discussion about how to fix this more
generically instead of adding device IDs for every new Intel GPU. I hope
this is the last patch to add device IDs.]
Link: https://lore.kernel.org/linux-pci/1537974841-29928-1-git-send-email-bmeng.cn@gmail.com
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
[bhelgaas: changelog]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: stable@vger.kernel.org # v3.4+
The few callers can just use dma_set_max_seg_size ()directly.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The two callers can just use dma_set_seg_boundary() directly.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Some PCI devices may have memory mapped in a BAR space that's intended for
use in peer-to-peer transactions. To enable such transactions the memory
must be registered with ZONE_DEVICE pages so it can be used by DMA
interfaces in existing drivers.
Add an interface for other subsystems to find and allocate chunks of P2P
memory as necessary to facilitate transfers between two PCI peers:
struct pci_dev *pci_p2pmem_find[_many]();
int pci_p2pdma_distance[_many]();
void *pci_alloc_p2pmem();
The new interface requires a driver to collect a list of client devices
involved in the transaction then call pci_p2pmem_find() to obtain any
suitable P2P memory. Alternatively, if the caller knows a device which
provides P2P memory, they can use pci_p2pdma_distance() to determine if it
is usable. With a suitable p2pmem device, memory can then be allocated
with pci_alloc_p2pmem() for use in DMA transactions.
Depending on hardware, using peer-to-peer memory may reduce the bandwidth
of the transfer but can significantly reduce pressure on system memory.
This may be desirable in many cases: for example a system could be designed
with a small CPU connected to a PCIe switch by a small number of lanes
which would maximize the number of lanes available to connect to NVMe
devices.
The code is designed to only utilize the p2pmem device if all the devices
involved in a transfer are behind the same PCI bridge. This is because we
have no way of knowing whether peer-to-peer routing between PCIe Root Ports
is supported (PCIe r4.0, sec 1.3.1). Additionally, the benefits of P2P
transfers that go through the RC is limited to only reducing DRAM usage
and, in some cases, coding convenience. The PCI-SIG may be exploring
adding a new capability bit to advertise whether this is possible for
future hardware.
This commit includes significant rework and feedback from Christoph
Hellwig.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
[bhelgaas: fold in fix from Keith Busch <keith.busch@intel.com>:
https://lore.kernel.org/linux-pci/20181012155920.15418-1-keith.busch@intel.com,
to address comment from Dan Carpenter <dan.carpenter@oracle.com>, fold in
https://lore.kernel.org/linux-pci/20181017160510.17926-1-logang@deltatee.com]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The threaded IRQ is naturally single threaded as desired, so use that to
simplify the AER bottom half handler. Since the root port structure has
much less to do now, remove the rpc construction helper routine.
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Use the recommended kernel API for writing to a concurrently-accessed
kfifo. No functional change here.
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The kernel provides a generic FIFO implementation, so no need to reinvent
that capability in a driver. Replace the AER-specific implementation with
the kernel-provided kfifo. Since the interrupt handler producer and work
queue consumer run single threaded, there is no need for additional
locking, so remove that lock, too.
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The AER struct aer_rpc was carrying a copy of the error source simply as a
temperary variable. Remove that from the structure and use a stack
variable for the purpose.
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The error recovery callbacks are only run on child devices. A Root Port is
never a child device, so this error resume callback was never invoked.
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
As done treewide earlier, this catches several more open-coded
allocation size calculations that were added to the kernel during the
merge window. This performs the following mechanical transformations
using Coccinelle:
kvmalloc(a * b, ...) -> kvmalloc_array(a, b, ...)
kvzalloc(a * b, ...) -> kvcalloc(a, b, ...)
devm_kzalloc(..., a * b, ...) -> devm_kcalloc(..., a, b, ...)
Signed-off-by: Kees Cook <keescook@chromium.org>
When the root complex suspends it must send a PME_Turn_Off TLP.
Implement this by asserting the "turnoff" reset.
On imx7d this functionality is part of the System Reset Controller (SRC)
and is exposed through the linux reset-controller subsystem.
On imx6 equivalent bits are in the IOMUXC pinmux controller General
Purpose Register (GPR) area which the imx6-pcie driver accesses
directly.
This is only for imx7d right now but it's deliberately implemented as an
optional reset, ignoring the chip variant:
* Older dtbs won't have this reset so it will be ignored.
* Future chips might also expose this as a reset controller.
For example imx8m (not yet supported) has the exact same
PCIE_CTRL_APPS_TURNOFF bit in the same location.
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
[lorenzo.pieralisi@arm.com: updated commit log]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
The PCI bus config accessors could be inlined into other accessor
functions, which makes it so they can't be traced. Force them to never be
inlined so that ftrace can hook into these functions.
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Addresses-Coverity-ID: 1472052 ("Missing break in switch")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Use kmemdup() rather than duplicating its implementation.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Michael Ellerman <mpe@ellerman.id.au>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/pci/hotplug/cpqphp_core.c: In function 'init_SERR':
drivers/pci/hotplug/cpqphp_core.c:124:5: warning: variable 'physical_slot' set but not used [-Wunused-but-set-variable]
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Currently, a hotplug bridge will be given hpmemsize additional memory
and hpiosize additional io if available, in order to satisfy any future
hotplug allocation requirements.
These calculations don't consider the current memory/io size of the
hotplug bridge/slot, so hotplug bridges/slots which have downstream
devices will be allocated their current allocation in addition to the
hpmemsize value.
This makes for possibly undesirable results with a mix of unoccupied and
occupied slots (ex, with hpmemsize=2M):
02:03.0 PCI bridge: <-- Occupied
Memory behind bridge: d6200000-d64fffff [size=3M]
02:04.0 PCI bridge: <-- Unoccupied
Memory behind bridge: d6500000-d66fffff [size=2M]
This change considers the current allocation size when using the
hpmemsize/hpiosize parameters to make the reservations predictable for
the mix of unoccupied and occupied slots:
02:03.0 PCI bridge: <-- Occupied
Memory behind bridge: d6200000-d63fffff [size=2M]
02:04.0 PCI bridge: <-- Unoccupied
Memory behind bridge: d6400000-d65fffff [size=2M]
Signed-off-by: Jon Derrick <jonathan.derrick@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
In order to have better power management for Thunderbolt PCIe chains,
Windows enables power management for native PCIe hotplug ports if there is
the following ACPI _DSD attached to the root port:
Name (_DSD, Package () {
ToUUID ("6211e2c0-58a3-4af3-90e1-927a4e0c55a4"),
Package () {
Package () {"HotPlugSupportInD3", 1}
}
})
This is also documented in:
https://docs.microsoft.com/en-us/windows-hardware/drivers/pci/dsd-for-pcie-root-ports#identifying-pcie-root-ports-supporting-hot-plug-in-d3
Do the same in Linux by introducing new firmware PM callback
(->bridge_d3()) and then implement it for ACPI based systems so that the
above property is checked.
There is one catch, though. The initial pci_dev->bridge_d3 is set before
the root port has ACPI companion bound (the device is not added to the PCI
bus either) so we need to look up the ACPI companion manually in that case
in acpi_pci_bridge_d3().
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Basically we need to do the same steps than what we do when system sleep is
entered and disable PME interrupt when the root port is runtime suspended.
This prevents spurious wakeups immediately when the port is transitioned
into D3cold.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Basically we need to do the same thing when runtime suspending than with
system sleep so re-use those operations here. This makes sure hotplug
interrupt does not trigger immediately when the link goes down.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
When PCIe port is runtime suspended/resumed some extra steps might be
needed to be executed from the port service driver side. For instance we
may need to disable PCIe hotplug interrupt to prevent it from triggering
immediately when PCIe link to the downstream component goes down.
To make the above possible add optional ->runtime_suspend() and
->runtime_resume() callbacks to struct pcie_port_service_driver and call
them for each port service in runtime suspend/resume callbacks of portdrv.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
[bhelgaas: adjust "slot->state" for 5790a9c78e ("PCI: pciehp: Unify
controller and slot structs")]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Currently we try to keep PCIe ports runtime suspended over system suspend
if possible. This mostly happens when entering suspend-to-idle because
there is no need to re-configure wake settings.
This causes problems if the parent port goes into D3cold and it gets
resumed upon exit from system suspend. This may happen for example if the
port is part of PCIe switch and the same switch is connected to a PCIe
endpoint that needs to be resumed. The way exit from D3cold works according
PCIe 4.0 spec 5.3.1.4.2 is that power is restored and cold reset is
signaled. After this the device is in D0unitialized state keeping PME
context if it supports wake from D3cold.
The problem occurs when a PCIe hotplug port is left suspended and the
parent port goes into D3cold and back to D0: the port keeps its PME context
but since everything else is reset back to defaults (D0unitialized) it is
not set to detect hotplug events anymore.
For this reason change the PCIe portdrv power management logic so that it
is fine to keep the port runtime suspended over system suspend but it needs
to be resumed upon exit to make sure it gets properly re-initialized.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
PCIe native hotplug shares MSI vector with native PME so the interrupt
handler might get called even the hotplug interrupt is masked. In that case
we should not handle any events because the interrupt was not meant for us.
Modify the PCIe hotplug interrupt handler to check this accordingly and
bail out if it finds out that the interrupt was not about hotplug.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Lukas Wunner <lukas@wunner.de>
When PCIe hotplug port is transitioned into D3hot, the link to the
downstream component will go down. If hotplug interrupt generation is
enabled when that happens, it will trigger immediately, waking up the
system and bringing the link back up.
To prevent this, disable hotplug interrupt generation when system suspend
is entered. This does not prevent wakeup from low power states according
to PCIe 4.0 spec section 6.7.3.4:
Software enables a hot-plug event to generate a wakeup event by
enabling software notification of the event as described in Section
6.7.3.1. Note that in order for software to disable interrupt generation
while keeping wakeup generation enabled, the Hot-Plug Interrupt Enable
bit must be cleared.
So as long as we have set the slot event mask accordingly, wakeup should
work even if slot interrupt is disabled. The port should trigger wake and
then send PME to the root port when the PCIe hierarchy is brought back up.
Limit this to systems using native PME mechanism to make sure older Apple
systems depending on commit e3354628c376 ("PCI: pciehp: Support interrupts
sent from D3hot") still continue working.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
We enable power management automatically for bridges where
pci_bridge_d3_possible() returns true. However, these bridges may have
ACPI methods such as _DSW that need to be called before D3 entry. For
example in Lenovo Thinkpad X1 Carbon 6th _DSW method is used to prepare
D3cold for the PCIe root port hosting Thunderbolt chain. Because wake is
not enabled _DSW method is never called and the port does not enter
D3cold properly consuming more power than necessary.
Users can work this around by writing "enabled" to "wakeup" sysfs file
under the device in question but that is not something an ordinary user
is expected to do.
Since we already automatically enable power management for PCIe ports
with ->bridge_d3 set extend that to enable wake for them as well,
assuming the port has any ACPI wakeup related objects implemented in the
namespace (adev->wakeup.flags.valid is true). This ensures the necessary
ACPI methods get called at appropriate times and allows the root port in
Thinkpad X1 Carbon 6th to go into D3cold.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Commit baecc470d5 ("PCI / PM: Skip bridges in pci_enable_wake()") changed
pci_enable_wake() so that all bridges are skipped when wakeup is enabled
(or disabled) with the reasoning that bridges can only signal wakeup on
behalf of their subordinate devices.
However, there are bridges that can signal wakeup themselves. For example
PCIe downstream and root ports supporting hotplug may signal wakeup upon
hotplug event.
For this reason change pci_enable_wake() so that it skips all bridges
except those that we power manage (->bridge_d3 is set). Those are the ones
that can go into low power states and may need to signal wakeup.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The spec has timing requirements when waiting for a link to become active
after a conventional reset. Implement those hard delays when waiting for
an active link so pciehp and dpc drivers don't need to duplicate this.
For devices that don't support data link layer active reporting, wait the
fixed time recommended by the PCIe spec.
Signed-off-by: Keith Busch <keith.busch@intel.com>
[bhelgaas: changelog]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Sinan Kaya <okaya@kernel.org>
Bring surprise removals and permanent failures together so we no longer
need separate flags. The implementation enforces that error handling will
not be able to override a surprise removal's permanent channel failure.
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Sinan Kaya <okaya@kernel.org>
A device still participates in error recovery even if it doesn't have
the error callbacks.
Always provide the status for user event watchers.
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Sinan Kaya <okaya@kernel.org>
There is no point in having a generic broadcast function if it needs to
have special cases for each callback it broadcasts.
Abstract the error broadcast to only the necessary information and removes
the now unnecessary helper to walk the bus.
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Sinan Kaya <okaya@kernel.org>
Going primarily by:
https://en.wikipedia.org/wiki/List_of_Intel_Atom_microprocessors
with additional information gleaned from other related pages; notably:
- Bonnell shrink was called Saltwell
- Moorefield is the Merriefield refresh which makes it Airmont
The general naming scheme is: FAM6_ATOM_UARCH_SOCTYPE
for i in `git grep -l FAM6_ATOM` ; do
sed -i -e 's/ATOM_PINEVIEW/ATOM_BONNELL/g' \
-e 's/ATOM_LINCROFT/ATOM_BONNELL_MID/' \
-e 's/ATOM_PENWELL/ATOM_SALTWELL_MID/g' \
-e 's/ATOM_CLOVERVIEW/ATOM_SALTWELL_TABLET/g' \
-e 's/ATOM_CEDARVIEW/ATOM_SALTWELL/g' \
-e 's/ATOM_SILVERMONT1/ATOM_SILVERMONT/g' \
-e 's/ATOM_SILVERMONT2/ATOM_SILVERMONT_X/g' \
-e 's/ATOM_MERRIFIELD/ATOM_SILVERMONT_MID/g' \
-e 's/ATOM_MOOREFIELD/ATOM_AIRMONT_MID/g' \
-e 's/ATOM_DENVERTON/ATOM_GOLDMONT_X/g' \
-e 's/ATOM_GEMINI_LAKE/ATOM_GOLDMONT_PLUS/g' ${i}
done
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vince Weaver <vincent.weaver@maine.edu>
Cc: dave.hansen@linux.intel.com
Cc: len.brown@intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Commit ee1604381a ("PCI: mvebu: Only remap I/O space if configured") had
the side effect that the PCI I/O mapping was created much earlier than
before, at a point where the probe() of the driver could still fail. This
is for example a problem if one gets an -EPROBE_DEFER at some point during
probe(), after pci_ioremap_io() has been called.
Indeed, there is currently no function to undo what pci_ioremap_io() did,
and switching to pci_remap_iospace() is not an option in pci-mvebu due to
the need for special memory attributes on Armada 38x.
Reverting ee1604381a ("PCI: mvebu: Only remap I/O space if configured")
would be a possibility, but it would require also reverting 42342073e3
("PCI: mvebu: Convert to use pci_host_bridge directly"). So instead, we use
an open-coded version of pci_host_probe() that creates the PCI I/O mapping
at a point where we are guaranteed not to fail anymore.
Fixes: ee1604381a ("PCI: mvebu: Only remap I/O space if configured")
Reported-by: Jan Kundrát <jan.kundrat@cesnet.cz>
Tested-by: Jan Kundrát <jan.kundrat@cesnet.cz>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
The PCI kirin driver compilation produces the following section mismatch
warning:
WARNING: vmlinux.o(.text+0x4758cc): Section mismatch in reference from
the function kirin_pcie_probe() to the function
.init.text:kirin_add_pcie_port()
The function kirin_pcie_probe() references
the function __init kirin_add_pcie_port().
This is often because kirin_pcie_probe lacks a __init
annotation or the annotation of kirin_add_pcie_port is wrong.
Remove '__init' from kirin_add_pcie_port() to fix it.
Fixes: fc5165db24 ("PCI: kirin: Add HiSilicon Kirin SoC PCIe controller driver")
Reported-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
[lorenzo.pieralisi@arm.com: updated commit log]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
This save some duplication for ia64, and makes the interface more
general. In the long run we want each dma_map_ops instance to fill this
out, but this will take a little more prep work.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
PCIe r4.0, sec 7.5.1.1.4 defines a new bit in the Status Register:
Immediate Readiness – This optional bit, when Set, indicates the Function
is guaranteed to be ready to successfully complete valid configuration
accesses at any time following any reset that the host is capable of
issuing Configuration Requests to this Function.
When this bit is Set, for accesses to this Function, software is exempt
from all requirements to delay configuration accesses following any type
of reset, including but not limited to the timing requirements defined in
Section 6.6.
This means that all delays after a Conventional or Function Reset can be
skipped.
This patch reads such bit and caches its value in a flag inside struct
pci_dev to be checked later if we should delay or can skip delays after a
reset. While at that, also move the explicit msleep(100) call from
pcie_flr() and pci_af_flr() to pci_dev_wait().
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
[bhelgaas: rename PCI_STATUS_IMMEDIATE to PCI_STATUS_IMM_READY]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Test the correct value to see whether the PHY get failed.
Use devm_phy_get() instead of devm_phy_optional_get(), since it is
only called if phy name is given in devicetree and so should exist.
If failure when getting or linking PHY, put any PHYs which were
already got and unlink them.
Fixes: dfb8053469 ("PCI: cadence: Add generic PHY support to host and EP drivers")
Reported-by: Colin King <colin.king@canonical.com>
Signed-off-by: Alan Douglas <adouglas@cadence.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
On 38+ Intel-based ASUS products, the NVIDIA GPU becomes unusable after S3
suspend/resume. The affected products include multiple generations of
NVIDIA GPUs and Intel SoCs. After resume, nouveau logs many errors such
as:
fifo: fault 00 [READ] at 0000005555555000 engine 00 [GR] client 04
[HUB/FE] reason 4a [] on channel -1 [007fa91000 unknown]
DRM: failed to idle channel 0 [DRM]
Similarly, the NVIDIA proprietary driver also fails after resume (black
screen, 100% CPU usage in Xorg process). We shipped a sample to NVIDIA for
diagnosis, and their response indicated that it's a problem with the parent
PCI bridge (on the Intel SoC), not the GPU.
Runtime suspend/resume works fine, only S3 suspend is affected.
We found a workaround: on resume, rewrite the Intel PCI bridge
'Prefetchable Base Upper 32 Bits' register (PCI_PREF_BASE_UPPER32). In the
cases that I checked, this register has value 0 and we just have to rewrite
that value.
Linux already saves and restores PCI config space during suspend/resume,
but this register was being skipped because upon resume, it already has
value 0 (the correct, pre-suspend value).
Intel appear to have previously acknowledged this behaviour and the
requirement to rewrite this register:
https://bugzilla.kernel.org/show_bug.cgi?id=116851#c23
Based on that, rewrite the prefetch register values even when that appears
unnecessary.
We have confirmed this solution on all the affected models we have in-hands
(X542UQ, UX533FD, X530UN, V272UN).
Additionally, this solves an issue where r8169 MSI-X interrupts were broken
after S3 suspend/resume on ASUS X441UAR. This issue was recently worked
around in commit 7bb05b85bc ("r8169: don't use MSI-X on RTL8106e"). It
also fixes the same issue on RTL6186evl/8111evl on an Aimfor-tech laptop
that we had not yet patched. I suspect it will also fix the issue that was
worked around in commit 7c53a72245 ("r8169: don't use MSI-X on
RTL8168g").
Thomas Martitz reports that this change also solves an issue where the AMD
Radeon Polaris 10 GPU on the HP Zbook 14u G5 is unresponsive after S3
suspend/resume.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=201069
Signed-off-by: Daniel Drake <drake@endlessm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-By: Peter Wu <peter@lekensteyn.nl>
CC: stable@vger.kernel.org
HP 6730b laptop has an ethernet NIC connected to one of the PCIe root
ports. The root ports themselves are native PCIe hotplug capable. Now,
during boot after PCI devices are scanned the BIOS triggers ACPI bus check
directly to the NIC:
ACPI: \_SB_.PCI0.RP06.NIC_: Bus check in hotplug_event()
It is not clear why it is sending bus check but regardless the ACPI hotplug
notify handler calls enable_slot() directly (instead of going through
acpiphp_check_bridge() as there is no bridge), which ends up handling
special case for non-hotplug bridges with native PCIe hotplug. This
results a crash of some kind but the reporter only sees black screen so it
is hard to figure out the exact spot and what actually happens. Based on
a few fix proposals it was tracked to crash somewhere inside
pci_assign_unassigned_bridge_resources().
In any case we should not really be in that special branch at all because
the ACPI notify happened to a slot that is not a PCI bridge (it is just a
regular PCI device).
Fix this so that we only go to that special branch if we are calling
enable_slot() for a bridge (e.g., the ACPI notification was for the
bridge).
Link: https://bugzilla.kernel.org/show_bug.cgi?id=201127
Fixes: 84c8b58ed3 ("ACPI / hotplug / PCI: Don't scan bridges managed by native hotplug")
Reported-by: Peter Anemone <peter.anemone@gmail.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
CC: stable@vger.kernel.org # v4.18+
If an Endpoint reported an error with ERR_FATAL, we previously ran driver
error recovery callbacks only for the Endpoint's driver. But if we reset a
Link to recover from the error, all downstream components are affected,
including the Endpoint, any multi-function peers, and children of those
peers.
Initiate the Link reset from the deepest Downstream Port that is
reliable, and call the error recovery callbacks for all its children.
If a Downstream Port (including a Root Port) reports an error, we assume
the Port itself is reliable and we need to reset its downstream Link. In
all other cases (Switch Upstream Ports, Endpoints, Bridges, etc), we assume
the Link leading to the component needs to be reset, so we initiate the
reset at the parent Downstream Port.
This allows two other clean-ups. First, we currently only use a Link
reset, which can only be initiated using a Downstream Port, so we can
remove checks for Endpoints. Second, the Downstream Port where we initiate
the Link reset is reliable (unlike components downstream from it), so the
special cases for error detect and resume are no longer necessary.
Signed-off-by: Keith Busch <keith.busch@intel.com>
[bhelgaas: changelog]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Sinan Kaya <okaya@kernel.org>
We don't need to be paranoid about the topology changing while handling an
error. If the device has changed in a hotplug capable slot, we can rely on
the presence detection handling to react to a changing topology.
Restore the fatal error handling behavior that existed before merging DPC
with AER with 7e9084b367 ("PCI/AER: Handle ERR_FATAL with removal and
re-enumeration of devices").
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Sinan Kaya <okaya@kernel.org>
It is a serious driver defect to enable MSI or MSI-X more than once. Doing
so may panic the kernel as in the stack trace below:
Call Trace:
sysfs_add_one+0xa5/0xd0
create_dir+0x7c/0xe0
sysfs_create_subdir+0x1c/0x20
internal_create_group+0x6d/0x290
sysfs_create_groups+0x4a/0xa0
populate_msi_sysfs+0x1cd/0x210
pci_enable_msix+0x31c/0x3e0
igbuio_pci_open+0x72/0x300 [igb_uio]
uio_open+0xcc/0x120 [uio]
chrdev_open+0xa1/0x1e0
[...]
do_sys_open+0xf3/0x1f0
SyS_open+0x1e/0x20
system_call_fastpath+0x16/0x1b
---[ end trace 11042e2848880209 ]---
Kernel panic - not syncing: stack-protector: Kernel stack is corrupted in: ffffffffa056b4fa
We want to keep the WARN_ON() and stack trace so the driver can be fixed,
but we can avoid the kernel panic by returning an error. We may still get
warnings like this:
Call Trace:
pci_enable_msix+0x3c9/0x3e0
igbuio_pci_open+0x72/0x300 [igb_uio]
uio_open+0xcc/0x120 [uio]
chrdev_open+0xa1/0x1e0
[...]
do_sys_open+0xf3/0x1f0
SyS_open+0x1e/0x20
system_call_fastpath+0x16/0x1b
------------[ cut here ]------------
WARNING: at fs/sysfs/dir.c:526 sysfs_add_one+0xa5/0xd0()
sysfs: cannot create duplicate filename '/devices/pci0000:00/0000:00:03.0/0000:01:00.1/msi_irqs'
Signed-off-by: Tonghao Zhang <xiangxia.m.yue@gmail.com>
[bhelgaas: changelog, fix patch whitespace, remove !!]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Errata i870 is applicable in both EP and RC mode. Therefore rename
function dra7xx_pcie_ep_unaligned_memaccess(), that implements errata
workaround, to dra7xx_pcie_unaligned_memaccess() and call it for both RC
and EP. Make sure driver probe does not fail in case the workaround is not
applied for RC mode in order to maintain DT backward compatibility.
Reported-by: Chris Welch <Chris.Welch@viavisolutions.com>
Signed-off-by: Vignesh R <vigneshr@ti.com>
[lorenzo.pieralisi@arm.com: reworded the log]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
PCI host drivers have already matched on compatible strings, so checking
device_type is redundant. Also, device_type is considered deprecated for
FDT though we've still been requiring it for PCI hosts as it is useful
for finding PCI buses.
Signed-off-by: Rob Herring <robh@kernel.org>
[lorenzo.pieralisi@arm.com: reformatted the log]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Alan Douglas <adouglas@cadence.com>
Acked-by: Subrahmaya Lingappa <l.subrahmanya@mobiveil.co.in>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Alan Douglas <adouglas@cadence.com>
Cc: Subrahmanya Lingappa <l.subrahmanya@mobiveil.co.in>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: linux-pci@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
iommu-map property is also used by devices with fsl-mc. This
patch moves the of_pci_map_rid to generic location, so that it
can be used by other busses too.
'of_pci_map_rid' is renamed here to 'of_map_rid' and there is no
functional change done in the API.
Signed-off-by: Nipun Gupta <nipun.gupta@nxp.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
In case of error, the function pci_create_slot() returns ERR_PTR() and
never returns NULL. The NULL test in the return value check should be
replaced with IS_ERR().
Fixes: a15f2c08c7 ("PCI: hv: support reporting serial number as slot information")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The secondary bus reset may have link side effects that a hotplug capable
port may incorrectly react to. Use the slot specific reset for hotplug
ports, fixing the undesirable link down-up handling during error
recovering.
Signed-off-by: Keith Busch <keith.busch@intel.com>
[bhelgaas: fold in
https://lore.kernel.org/linux-pci/20180926152326.14821-1-keith.busch@intel.com
for issue reported by Stephen Rothwell <sfr@canb.auug.org.au>]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Sinan Kaya <okaya@kernel.org>
The AER driver has never read the config space of an endpoint that reported
a fatal error because the link to that device is considered unreliable.
An ERR_FATAL from an upstream port almost certainly indicates an error on
its upstream link, so we can't expect to reliably read its config space for
the same reason.
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Sinan Kaya <okaya@kernel.org>
Error handling may be running in parallel with a hot removal. Reference
count the device during AER handling so the device can not be freed while
AER wants to reference it.
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Sinan Kaya <okaya@kernel.org>
When programming the inbound/outbound ATUs, we call usleep_range() after
each checking PCIE_ATU_ENABLE bit. Unfortunately, the ATU programming
can be executed in atomic context:
inbound ATU programming could be called through
pci_epc_write_header()
=>dw_pcie_ep_write_header()
=>dw_pcie_prog_inbound_atu()
outbound ATU programming could be called through
pci_bus_read_config_dword()
=>dw_pcie_rd_conf()
=>dw_pcie_prog_outbound_atu()
Fix this issue by calling mdelay() instead.
Fixes: f8aed6ec62 ("PCI: dwc: designware: Add EP mode support")
Fixes: d8bbeb39fb ("PCI: designware: Wait for iATU enable")
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
[lorenzo.pieralisi@arm.com: commit log update]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
This patch provides DPC save and restore capabilities. This is necessary
for the driver to observe DPC events in the event the configuration space
needs to be restored after a reset.
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Sinan Kaya <okaya@kernel.org>
The port's config space may be cleared after a link reset, which wipes out
the bridge's bus and memory windows. Restore the config space that was
saved during probe so we can access downstream devices.
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Sinan Kaya <okaya@kernel.org>
The PCI port driver saves the PCI state after initializing the device with
the applicable service devices. This was, however, before the service
drivers were even registered because PCI probe happens before the
device_initcall initialized those service drivers. The config space state
that the services set up were not being saved. The end result would cause
PCI devices to not react to events that the drivers think they did if the
PCI state ever needed to be restored.
Fix this by changing the service drivers from using the init calls to
having the portdrv driver calling the services directly. This will get the
state saved as desired, while making the relationship between the port
driver and the services under it more explicit in the code.
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Sinan Kaya <okaya@kernel.org>
While refactoring the PCI hotplug core's API, I noticed a significant
amount of technical debt in some of the hotplug drivers. Document the
issues that caught my eye for starters.
I do not have hardware at my disposal that utilizes the listed drivers
and I think that's a prerequisite to work on them to ensure that no
regressions sneak in. But some of this hardware is so old that it may be
hard to come by. Obviously, it is fine to support old hardware, but the
drivers need to be maintained.
If noone steps up, perhaps we should consider sunsetting a few drivers
by moving them to staging. Based on my findings, ibmphp would be the
first candidate. I've found it fairly difficult to apply my API
refactorings to it and have listed some obvious bugs in the driver.
cpqphp is also in need of a modernization and would be a second
candidate for relegation to staging.
shpchp was introduced in the same commit as pciehp but hasn't benefited
from the same amount of refactoring due to the decline of conventional
PCI's relevance. Yet hardware supporting it may be more prevalent than
for the proprietary hotplug methods.
Per Documentation/process/2.Process.rst, "a TODO file should be present"
for drivers in staging. The file introduced by the present commit may
serve as a basis for this.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Scott Murray <scott@spiteful.org>
Cc: Dan Zink <dan.zink@hpe.com>
Cc: Prarit Bhargava <prarit@redhat.com>
When the PCI hotplug core and its first user, cpqphp, were introduced in
February 2002 with historic commit a8a2069f432c, cpqphp allocated a slot
struct for its internal use plus a hotplug_slot struct to be registered
with the hotplug core and linked the two with pointers:
https://git.kernel.org/tglx/history/c/a8a2069f432c
Nowadays, the predominant pattern in the tree is to embed ("subclass")
such structures in one another and cast to the containing struct with
container_of(). But it wasn't until July 2002 that container_of() was
introduced with historic commit ec4f214232cf:
https://git.kernel.org/tglx/history/c/ec4f214232cf
pnv_php, introduced in 2016, did the right thing and embedded struct
hotplug_slot in its internal struct pnv_php_slot, but all other drivers
cargo-culted cpqphp's design and linked separate structs with pointers.
Embedding structs is preferrable to linking them with pointers because
it requires fewer allocations, thereby reducing overhead and simplifying
error paths. Casting an embedded struct to the containing struct
becomes a cheap subtraction rather than a dereference. And having fewer
pointers reduces the risk of them pointing nowhere either accidentally
or due to an attack.
Convert all drivers to embed struct hotplug_slot in their internal slot
struct. The "private" pointer in struct hotplug_slot thereby becomes
unused, so drop it.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Tyrel Datwyler <tyreld@linux.vnet.ibm.com> # drivers/pci/hotplug/rpa*
Acked-by: Sebastian Ott <sebott@linux.ibm.com> # drivers/pci/hotplug/s390*
Acked-by: Andy Shevchenko <andy.shevchenko@gmail.com> # drivers/platform/x86
Cc: Len Brown <lenb@kernel.org>
Cc: Scott Murray <scott@spiteful.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Oliver OHalloran <oliveroh@au1.ibm.com>
Cc: Gavin Shan <gwshan@linux.vnet.ibm.com>
Cc: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Cc: Corentin Chary <corentin.chary@gmail.com>
Cc: Darren Hart <dvhart@infradead.org>
Ever since the PCI hotplug core was introduced in 2002, drivers had to
allocate and register a struct hotplug_slot_info for every slot:
https://git.kernel.org/tglx/history/c/a8a2069f432c
Apparently the idea was that drivers furnish the hotplug core with an
up-to-date card presence status, power status, latch status and
attention indicator status as well as notify the hotplug core of changes
thereof. However only 4 out of 12 hotplug drivers bother to notify the
hotplug core with pci_hp_change_slot_info() and the hotplug core never
made any use of the information: There is just a single macro in
pci_hotplug_core.c, GET_STATUS(), which uses the hotplug_slot_info if
the driver lacks the corresponding callback in hotplug_slot_ops. The
macro is called when the user reads the attribute via sysfs.
Now, if the callback isn't defined, the attribute isn't exposed in sysfs
in the first place (see e.g. has_power_file()). There are only two
situations when the hotplug_slot_info would actually be accessed:
* If the driver defines ->enable_slot or ->disable_slot but not
->get_power_status.
* If the driver defines ->set_attention_status but not
->get_attention_status.
There is no driver doing the former and just a single driver doing the
latter, namely pnv_php.c. Amend it with a ->get_attention_status
callback. With that, the hotplug_slot_info becomes completely unused by
the PCI hotplug core. But a few drivers use it internally as a cache:
cpcihp uses it to cache the latch_status and adapter_status.
cpqhp uses it to cache the adapter_status.
pnv_php and rpaphp use it to cache the attention_status.
shpchp uses it to cache all four values.
Amend these drivers to cache the information in their private slot
struct. shpchp's slot struct already contains members to cache the
power_status and adapter_status, so additional members are only needed
for the other two values. In the case of cpqphp, the cached value is
only accessed in a single place, so instead of caching it, read the
current value from the hardware.
Caution: acpiphp, cpci, cpqhp, shpchp, asus-wmi and eeepc-laptop
populate the hotplug_slot_info with initial values on probe. That code
is herewith removed. There is a theoretical chance that the code has
side effects without which the driver fails to function, e.g. if the
ACPI method to read the adapter status needs to be executed at least
once on probe. That seems unlikely to me, still maintainers should
review the changes carefully for this possibility.
Rafael adds: "I'm not aware of any case in which it will break anything,
[...] but if that happens, it may be necessary to add the execution of
the control methods in question directly to the initialization part."
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Tyrel Datwyler <tyreld@linux.vnet.ibm.com> # drivers/pci/hotplug/rpa*
Acked-by: Sebastian Ott <sebott@linux.ibm.com> # drivers/pci/hotplug/s390*
Acked-by: Andy Shevchenko <andy.shevchenko@gmail.com> # drivers/platform/x86
Cc: Len Brown <lenb@kernel.org>
Cc: Scott Murray <scott@spiteful.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Oliver OHalloran <oliveroh@au1.ibm.com>
Cc: Gavin Shan <gwshan@linux.vnet.ibm.com>
Cc: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Cc: Corentin Chary <corentin.chary@gmail.com>
Cc: Darren Hart <dvhart@infradead.org>
Hotplug drivers cannot declare their hotplug_slot_ops const, making them
attractive targets for attackers, because upon registration of a hotplug
slot, __pci_hp_initialize() writes to the "owner" and "mod_name" members
in that struct.
Fix by moving these members to struct hotplug_slot and constify every
driver's hotplug_slot_ops except for pciehp.
pciehp constructs its hotplug_slot_ops at runtime based on the PCIe
port's capabilities, hence cannot declare them const. It can be
converted to __write_rarely once that's mainlined:
http://www.openwall.com/lists/kernel-hardening/2016/11/16/3
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Tyrel Datwyler <tyreld@linux.vnet.ibm.com> # drivers/pci/hotplug/rpa*
Acked-by: Andy Shevchenko <andy.shevchenko@gmail.com> # drivers/platform/x86
Cc: Len Brown <lenb@kernel.org>
Cc: Scott Murray <scott@spiteful.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Oliver OHalloran <oliveroh@au1.ibm.com>
Cc: Gavin Shan <gwshan@linux.vnet.ibm.com>
Cc: Sebastian Ott <sebott@linux.vnet.ibm.com>
Cc: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Cc: Corentin Chary <corentin.chary@gmail.com>
Cc: Darren Hart <dvhart@infradead.org>
The members in pciehp's controller struct are arranged in a seemingly
arbitrary order and have grown to an amount that I no longer consider
easily graspable by contributors.
Sort the members into 5 rubrics:
* Slot Capabilities register and quirks
* Slot Control register access
* Slot Status register event handling
* state machine
* hotplug core interface
Obviously, this is just my personal bikeshed color and if anyone has a
better idea, please come forward. Any ordering will do as long as the
information is presented in a manageable manner.
No functional change intended.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Of the members which were just moved from pciehp's slot struct to the
controller struct, rename "lock" to "state_lock" and rename "work" to
"button_work" for clarity. Perform the rename separately to the
unification of the two structs per Sinan's request.
No functional change intended.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Sinan Kaya <okaya@kernel.org>
pciehp was originally introduced together with shpchp in a single
commit, c16b4b14d980 ("PCI Hotplug: Add SHPC and PCI Express hot-plug
drivers"):
https://git.kernel.org/tglx/history/c/c16b4b14d980
shpchp supports up to 31 slots per controller, hence uses separate slot
and controller structs. pciehp has a 1:1 relationship between slot and
controller and therefore never required this separation. Nevertheless,
because much of the code had been copy-pasted between the two drivers,
pciehp likewise uses separate structs to this very day.
The artificial separation of data structures adds unnecessary complexity
and bloat to pciehp and requires constantly chasing pointers at runtime.
Simplify the driver by merging struct slot into struct controller.
Merge the slot constructor pcie_init_slot() and the destructor
pcie_cleanup_slot() into the controller counterparts.
No functional change intended.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The WiGig Bus Extension (WBE) specification allows tunneling PCIe over
IEEE 802.11. A product implementing this spec is the wil6210 from
Wilocity (now part of Qualcomm Atheros). It integrates a PCIe switch
with a wireless network adapter:
00.0-+ [1ae9:0101] Upstream Port
+-00.0-+ [1ae9:0200] Downstream Port
| +-00.0 [168c:0034] Atheros AR9462 Wireless Network Adapter
+-02.0 [1ae9:0201] Downstream Port
+-03.0 [1ae9:0201] Downstream Port
Wirelessly attached devices presumably appear below the hotplug ports
with device ID [1ae9:0201]. Oddly, the Downstream Port [1ae9:0200]
leading to the wireless network adapter is likewise Hotplug Capable,
but has its Presence Detect State bit hardwired to zero. Even if the
Link Active bit is set, Presence Detect is zero, so this cannot be
caused by in-band presence detection but only by broken hardware.
pciehp assumes an empty slot if Presence Detect State is zero,
regardless of Link Active being one. Consequently, up until v4.18 it
removes the wireless network adapter in pciehp_resume(). From v4.19 it
already does so in pciehp_probe().
Be lenient towards broken hardware and assume the slot is occupied if
Link Active is set: Introduce pciehp_card_present_or_link_active()
and use it in lieu of pciehp_get_adapter_status() everywhere, except
in pciehp_handle_presence_or_link_change() whose log messages depend
on which of Presence Detect State or Link Active is set.
Remove the Presence Detect State check from __pciehp_enable_slot()
because it is only called if either of Presence Detect State or Link
Active is set.
Caution: There is a possibility that broken hardware exists which has
working Presence Detect but hardwires Link Active to one. On such
hardware the slot will now incorrectly be considered always occupied.
If such hardware is discovered, this commit can be rolled back and a
quirk can be added which sets is_hotplug_bridge = 0 for [1ae9:0200].
Link: https://bugzilla.kernel.org/show_bug.cgi?id=200839
Reported-and-tested-by: David Yang <mmyangfl@gmail.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Rajat Jain <rajatja@google.com>
Cc: Ashok Raj <ashok.raj@intel.com>
Now that ASPM is configured for *all* PCIe devices at boot, a problem is
seen with systems that set the FADT NO_ASPM bit. This bit indicates that
the OS should not alter the ASPM state, but when
pcie_aspm_init_link_state() runs it only checks for !aspm_support_enabled.
This misses the ACPI_FADT_NO_ASPM case because that is setting
aspm_disabled.
The result is systems may hang at boot after 1302fcf; avoidable if they
boot with pcie_aspm=off (sets !aspm_support_enabled).
Fix this by having aspm_init_link_state() check for either
!aspm_support_enabled or acpm_disabled.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=201001
Fixes: 1302fcf0d0 ("PCI: Configure *all* devices, not just hot-added ones")
Signed-off-by: Patrick Talbert <ptalbert@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Check return value of devm_pci_remap_iospace().
Addresses-Coverity-ID: 1471965 ("Unchecked return value")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Honghui Zhang <honghui.zhang@mediatek.com>
The driver does not cope with the fact that probe can fail in a number
of cases after enabling runtime PM on the device; this results in
warnings about "Unbalanced pm_runtime_enable". Furthermore if probe
fails after invoking qcom_pcie_host_init() the power-domain will be left
referenced.
As it is not possible for the error handling in qcom_pcie_host_init() to
handle errors happening after returning from that function the
pm_runtime_get_sync() is moved to qcom_pcie_probe() as well.
Fixes: 854b69efbd ("PCI: qcom: add runtime pm support to pcie_port")
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
[lorenzo.pieralisi@arm.com: updated commit log]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Stanimir Varbanov <svarbanov@mm-sol.com>
On imx7d the pcie-phy power domain is turned off in suspend and this can
make the system hang after resume when attempting any read from PCI.
Fix this by adding minimal suspend/resume code. This will prepare for
powering down on suspend and reset the block on resume.
Code is only for imx7d but a very similar sequence can be used for
other SOCs.
Original-by: Richard Zhu <hongxing.zhu@nxp.com>
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
[lorenzo.pieralisi@arm.com: commit log update]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
The power up defaults of the MPLL are designed for the standard 125MHz
refclock derived from the ENET PLL. As this clock has a jitter that
violates the PCIe Gen2 timing requirements, some board designs use
an external reference clock generator. Those clock generators may
output a clock at a different rate than what the MPLL expects
(usually a 100MHz clock, to re-use the PCIe bus clock).
In that case the MPLL must be reconfigured via overrides to use
different refclock dividers and loop multipliers. The i.MX6
reference manual lists both 100MHz and 200MHz as supported refclock
rates and the associated mult and div values.
Only the 100MHz setup has been tested on a real board, but since the
200MHz setup only differs in the used pre-divider it seems safe to
add it now.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Richard Zhu <hongxing.zhu@nxp.com>
Fix previous incorrect logic that limits PAXC slot number to zero only.
In order for SRIOV/VF to work, we need to allow the slot number to be
greater than zero.
Fixes: 46560388c4 ("PCI: iproc: Allow multiple devices except on PAXC")
Signed-off-by: Jitendra Bhivare <jitendra.bhivare@broadcom.com>
Signed-off-by: Ray Jui <ray.jui@broadcom.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Andy Gospodarek <gospo@broadcom.com>
Dave writes:
"Various fixes, all over the place:
1) OOB data generation fix in bluetooth, from Matias Karhumaa.
2) BPF BTF boundary calculation fix, from Martin KaFai Lau.
3) Don't bug on excessive frags, to be compatible in situations mixing
older and newer kernels on each end. From Juergen Gross.
4) Scheduling in RCU fix in hv_netvsc, from Stephen Hemminger.
5) Zero keying information in TLS layer before freeing copies
of them, from Sabrina Dubroca.
6) Fix NULL deref in act_sample, from Davide Caratti.
7) Orphan SKB before GRO in veth to prevent crashes with XDP,
from Toshiaki Makita.
8) Fix use after free in ip6_xmit, from Eric Dumazet.
9) Fix VF mac address regression in bnxt_en, from Micahel Chan.
10) Fix MSG_PEEK behavior in TLS layer, from Daniel Borkmann.
11) Programming adjustments to r8169 which fix not being to enter deep
sleep states on some machines, from Kai-Heng Feng and Hans de
Goede.
12) Fix DST_NOCOUNT flag handling for ipv6 routes, from Peter
Oskolkov."
* gitolite.kernel.org:/pub/scm/linux/kernel/git/davem/net: (45 commits)
net/ipv6: do not copy dst flags on rt init
qmi_wwan: set DTR for modems in forced USB2 mode
clk: x86: Stop marking clocks as CLK_IS_CRITICAL
r8169: Get and enable optional ether_clk clock
clk: x86: add "ether_clk" alias for Bay Trail / Cherry Trail
r8169: enable ASPM on RTL8106E
r8169: Align ASPM/CLKREQ setting function with vendor driver
Revert "kcm: remove any offset before parsing messages"
kcm: remove any offset before parsing messages
net: ethernet: Fix a unused function warning.
net: dsa: mv88e6xxx: Fix ATU Miss Violation
tls: fix currently broken MSG_PEEK behavior
hv_netvsc: pair VF based on serial number
PCI: hv: support reporting serial number as slot information
bnxt_en: Fix VF mac address regression.
ipv6: fix possible use-after-free in ip6_xmit()
net: hp100: fix always-true check for link up state
ARM: dts: at91: add new compatibility string for macb on sama5d3
net: macb: disable scatter-gather for macb on sama5d3
net: mvpp2: let phylink manage the carrier state
...
