i915 expects the OpRegion to be cached (i.e. not __iomem), so explicitly
map it with memremap rather than the implied cache setting of
acpi_os_ioremap().
Cc: Daniel Vetter <daniel.vetter@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: intel-gfx@lists.freedesktop.org
Cc: David Airlie <airlied@linux.ie>
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Latest VBT mentions which set of registers will be used for BLC,
as controller number field. Making use of this field in BXT
BLC implementation. Also, the registers are used in case control
pin indicates display DDI. Adding a check for this.
According to Bspec, BLC_PWM_*_2 uses the display utility pin for output.
To use backlight 2, enable the utility pin with mode = PWM
v2: Jani's review comments
addressed
- Add a prefix _ to BXT BLC registers definitions.
- Add "bxt only" comment for u8 controller
- Remove control_pin check for DDI controller
- Check for valid controller values
- Set pipe bits in UTIL_PIN_CTL
- Enable/Disable UTIL_PIN_CTL in enable/disable_backlight()
- If BLC 2 is used, read active_low_pwm from UTIL_PIN polarity
Satheesh's review comment addressed
- If UTIL PIN is already enabled, BIOS would have programmed it. No
need to disable and enable again.
v3: Jani's review comments
- add UTIL_PIN_PIPE_MASK and UTIL_PIN_MODE_MASK
- Disable UTIL_PIN if controller 1 is used
- Mask out UTIL_PIN_PIPE_MASK and UTIL_PIN_MODE_MASK before enabling
UTIL_PIN
- check valid controller value in intel_bios.c
- add backlight.util_pin_active_low
- disable util pin before enabling
v4: Change for BXT-PO branch:
Stubbed unwanted definition which was existing before
because of DC6 patch.
UTIL_PIN_MODE_PWM (0x1b << 24)
v2: Fixed Jani's review comment.
v3: Split the backight PWM frequency programming into separate patch,
in cases BIOS doesn't initializes it.
v4: Starting afresh and not modifying existing state for backlight, as
per Jani's recommendation.
v5: Fixed Jani's review comment wrt util pin enable
Signed-off-by: Vandana Kannan <vandana.kannan@intel.com>
Signed-off-by: Sunil Kamath <sunil.kamath@intel.com>
Signed-off-by: Uma Shankar <uma.shankar@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Previously we've relied on having basically one backlight and one
backlight type per platform. This is already a bit quirky with PMIC PWM
support on VLV/CHV platforms with MIPI DSI. In the foreseeable future
we'll have at least DPCD based backlight control on eDP and DCS command
based backlight control on MIPI DSI. Backlight is becoming more and more
connector specific, so reflect this fact by making the backlight control
hooks connector specific.
This enables further work to reuse generic backlight code in
intel_panel.c while adding more specific backlight code accessed via the
hooks.
Cc: Deepak M <m.deepak@intel.com>
Cc: Yetunde Adebisi <yetundex.adebisi@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Deepak M <m.deepak@intel.com>
Reviewed-by: Yetunde Adebisi <yetundex.adebisi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Make adjusted_mode const whereever we don't have to modify it. This only
covers cases when we have a local adjusted_mode variable, and doesn't
make any difference for cases where we just dereference
pipe_config->adjusted_mode.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Mika Kahola <mika.kahola@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The adjustead_mode crtc_ timings are what we will program into the hardware,
so it's those timings we should be looking practically everywhere.
The normal and crtc_ timings should differ only when stere doubling is
used. In that case the normal timings are the orignal non-doubled
timigns, and crtc_ timings are the doubled timings used by the hardware.
The only case where we continue to look at the normal timings is when we
pass the adjusted_mode to drm_match_{cea,hdmi}_mode() to find the VIC.
drm_edid keeps the modes aronund in the non-double form only, so it
needs the non-double timings to match against.
Done with sed
's/adjusted_mode->\([vhVH]\)/adjusted_mode->crtc_\1/g'
's/adjusted_mode->clock/adjusted_mode->crtc_clock/g'
with a manual s/VDisplay/vdisplay/ within the comment in intel_dvo.c
v2: Update due to intel_dsi.c changes
Reviewed-by: Mika Kahola <mika.kahola@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Rename the function argument to 'adjusted_mode' whenever the function
only ever gets passed the adjusted_mode.
v2: Update due to intel_dsi.c changes
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Mika Kahola <mika.kahola@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Currently everyone and their dog has their own favourite spelling
for vga_switcheroo. This makes it hard to grep dmesg for log entries
relating to vga_switcheroo. It also makes it hard to find related
source files in the tree.
vga_switcheroo.c uses pr_fmt "vga_switcheroo". Use that everywhere.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Fall back to VBT based backlight modulation frequency if it's not
set. Do not hard code.
This could be a problem if there is no VBT.
Cc: Clint Taylor <clinton.a.taylor@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Tested-by: Clint Taylor <Clinton.A.Taylor@intel.com>
Reviewed-by: Clint Taylor <Clinton.A.Taylor@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Normally we determine the backlight PWM modulation frequency (which we
also use as backlight max value) from the backlight registers at module
load time, expecting the registers have been initialized by the BIOS. If
this is not the case, we fail.
The VBT contains the backlight modulation frequency in Hz. Add platform
specific functions to convert the frequency in Hz to backlight PWM
modulation frequency, and use them to initialize the backlight when the
registers are not initialized by the BIOS.
v2: Fix SPT and VLV. Thanks to Clint for the VLV code.
Cc: Clint Taylor <clinton.a.taylor@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Clint Taylor <Clinton.A.Taylor@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Currently the difference between backlight control on HSW vs. BDW/SKL is
that on HSW we modify the duty cycle on the CPU register, and have the
hardware pass the changes on to the PCH registers. We still drive the
PCH PWM on both. While HSW and BDW use the same LPT PCH, BDW does not
pass these messages on to the PCH. Therefore on BDW we need to enable
the PCH override bit, and program the PCH directly. (On SPT PCH, this
mode is the default.) We could as well do this on HSW too, and in fact
I've been told this is what a certain other operating system does. So
use PCH backlight override on HSW too.
This simplifies some follow-up code, but it does have the danger of
breaking backlight on HSW machines. It should work, but mysterious are
the ways of backlight.
While at it, name the related backlight hooks according to the PCH
rather than the CPU for clarity.
Cc: Clint Taylor <clinton.a.taylor@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Clint Taylor <Clinton.A.Taylor@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Use the CRC PWM device in intel_panel.c and add new MIPI backlight
specififc callbacks
v2: Modify to use pwm_config callback
v3: Addressed Jani's comments
- Renamed all function as pwm_* instead of vlv_*
- Call intel_panel_actually_set_backlight in enable function
- Return -ENODEV in case pwm_get fails
- in case pwm_config error return error cdoe from pwm_config
- Cleanup pwm in intel_panel_destroy_backlight
v4: Removed unused #defines and initialized backlight with INVALID_PIPE (Ville)
CC: Samuel Ortiz <sameo@linux.intel.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Tested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Shobhit Kumar <shobhit.kumar@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Some 855gm models (at least ThinkPad X40) regressed because of
commit b0cd324fae
Author: Jani Nikula <jani.nikula@intel.com>
Date: Wed Nov 12 16:25:43 2014 +0200
drm/i915: don't save/restore backlight hist ctl registers
which tried to make our driver more robust by not blindly saving and
restoring registers, but it failed to take into account
commit 0eb96d6ed3
Author: Jesse Barnes <jbarnes@virtuousgeek.org>
Date: Wed Oct 14 12:33:41 2009 -0700
drm/i915: save/restore BLC histogram control reg across suspend/resume
Fix the regression by enabling hist ctl on gen2.
v2: Improved the comment.
v3: Improved the comment, again.
Reported-and-tested-by: Philipp Gesang <phg@phi-gamma.net>
References: http://mid.gmane.org/20150623222648.GD12335@acheron
Fixes: b0cd324fae ("drm/i915: don't save/restore backlight hist ctl registers")
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: stable@vger.kernel.org
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Enabling BLC on BXT.
Includes register definition, and new functions for BXT.
In BXT, there are 2 sets of registers for BLC. Until there is clarity
about which set would be effective, set 1 is being used.
This would have to be re-visited if there is any change or when 2 LFPs are
enabled on BXT.
This patch enables brightness change which would be effected by use of
hot-keys or sysfs entry.
TODO:- BLC implementation will have to re-visited when
1. there is clarity about which set of registers has to be used and when.
2. CDCLK frequency is changed
v2: Jani's review comments
- Modified comment in i915_reg.h
- Renamed register defintions
- Removed definition of duty cycle max. Not required now and its not 64-bit.
v3:
- Rebase on top of VLV/CHV backlight changes, in particuliar
bxt_set_backlight() now has a different prototype (Damien)
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Vandana Kannan <vandana.kannan@intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Shankar, Uma <uma.shankar@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We have grown a number of different implementations of
DIV_ROUND_CLOSEST_ULL throughout the kernel. Move the i915 one to
kernel.h so that it can be reused.
Signed-off-by: Javi Merino <javi.merino@arm.com>
Reviewed-by: Jeff Epler <jepler@unpythonic.net>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Guenter Roeck <linux@roeck-us.net>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: "Rafael J. Wysocki" <rafael.j.wysocki@intel.com>
Cc: Alex Elder <elder@linaro.org>
Cc: Antti Palosaari <crope@iki.fi>
Cc: Javi Merino <javi.merino@arm.com>
Cc: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Mike Turquette <mturquette@linaro.org>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Cc: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull drm updates from Dave Airlie:
"This is the main drm pull, it has a shared branch with some alsa
crossover but everything should be acked by relevant people.
New drivers:
- ATMEL HLCDC driver
- designware HDMI core support (used in multiple SoCs).
core:
- lots more atomic modesetting work, properties and atomic ioctl
(hidden under option)
- bridge rework allows support for Samsung exynos chromebooks to
work finally.
- some more panels supported
i915:
- atomic plane update support
- DSI uses shared DSI infrastructure
- Skylake basic support is all merged now
- component framework used for i915/snd-hda interactions
- write-combine cpu memory mappings
- engine init code refactored
- full ppgtt enabled where execlists are enabled.
- cherryview rps/gpu turbo and pipe CRC support.
radeon:
- indirect draw support for evergreen/cayman
- SMC and manual fan control for SI/CI
- Displayport audio support
amdkfd:
- SDMA usermode queue support
- replace suballocator usage with more suitable one
- rework for allowing interfacing to more than radeon
nouveau:
- major renaming in prep for later splitting work
- merge arm platform driver into nouveau
- GK20A reclocking support
msm:
- conversion to atomic modesetting
- YUV support for mdp4/5
- eDP support
- hw cursor for mdp5
tegra:
- conversion to atomic modesetting
- better suspend/resume support for child devices
rcar-du:
- interlaced support
imx:
- move to using dw_hdmi shared support
- mode_fixup support
sti:
- DVO support
- HDMI infoframe support
exynos:
- refactoring and cleanup, removed lots of internal unnecessary
abstraction
- exynos7 DECON display controller support
Along with the usual bunch of fixes, cleanups etc"
* 'drm-next' of git://people.freedesktop.org/~airlied/linux: (724 commits)
drm/radeon: fix voltage setup on hawaii
drm/radeon/dp: Set EDP_CONFIGURATION_SET for bridge chips if necessary
drm/radeon: only enable kv/kb dpm interrupts once v3
drm/radeon: workaround for CP HW bug on CIK
drm/radeon: Don't try to enable write-combining without PAT
drm/radeon: use 0-255 rather than 0-100 for pwm fan range
drm/i915: Clamp efficient frequency to valid range
drm/i915: Really ignore long HPD pulses on eDP
drm/exynos: Add DECON driver
drm/i915: Correct the base value while updating LP_OUTPUT_HOLD in MIPI_PORT_CTRL
drm/i915: Insert a command barrier on BLT/BSD cache flushes
drm/i915: Drop vblank wait from intel_dp_link_down
drm/exynos: fix NULL pointer reference
drm/exynos: remove exynos_plane_dpms
drm/exynos: remove mode property of exynos crtc
drm/exynos: Remove exynos_plane_dpms() call with no effect
drm/i915: Squelch overzealous uncore reset WARN_ON
drm/i915: Take runtime pm reference on hangcheck_info
drm/i915: Correct the IOSF Dev_FN field for IOSF transfers
drm/exynos: fix DMA_ATTR_NO_KERNEL_MAPPING usage
...
The objective is to make this structure usable with the atomic helpers,
so let's start with the rename. Patch generated with coccinelle:
@@ @@
-struct intel_crtc_config {
+struct intel_crtc_state {
...
}
@@ @@
-struct intel_crtc_config
+struct intel_crtc_state
v2: Completely generate the patch with cocci. (Ander)
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
commit 6dda730e55
Author: Jani Nikula <jani.nikula@intel.com>
Date: Tue Jun 24 18:27:40 2014 +0300
drm/i915: respect the VBT minimum backlight brightness
introduced a bug which resulted in inconsistent brightness levels on
different machines. If a suspended was entered with the screen off some
machines would resume with the screen at minimum brightness and others
at maximum brightness.
The following commands can be used to produce this behavior.
xset dpms force off
sleep 1
sudo systemctl suspend
(resume ...)
The root cause of this problem is a comparison which checks to see if
the backlight level is zero when the panel is enabled. If it is zero,
it is set to the maximum level. Unfortunately, not all machines have a
minimum level of zero. On those machines the level is left at the
minimum instead of begin set to the maximum.
Fix the bug by updating the comparison to check for the minimum
backlight level instead of zero. Also, expand the comparison for
the possible case when the level is less than the minimum.
Fixes: 6dda730e55 ("respect the VBT minimum backlight brightness")
Signed-off-by: Jeremiah Mahler <jmmahler@gmail.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
So with all the code movement and extraction in intel_pm.c in -next
git is hopelessly confused with
commit 2208d655a9
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Fri Nov 14 09:25:29 2014 +0100
drm/i915: drop WaSetupGtModeTdRowDispatch:snb
from -fixes. Worse even small changes in -next move around the
conflict context so rerere is equally useless. Let's just backmerge
and be done with it.
Conflicts:
drivers/gpu/drm/i915/i915_drv.c
drivers/gpu/drm/i915/intel_pm.c
Except for git getting lost no tricky conflicts really.
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Now that the backlight device no longer gets registered too early we
should be able to drop most of the INVALID_PIPE checks from the backlight
code.
The only exceptio is the opregion stuff where we may (in theory at
least) get a request from the BIOS already during driver init as soon as
the backlight setup has been done. In which case we can still get the
INVALID_PIPE from intel_get_pipe_from_connector(). So leave that check
in place, and add a comment explaining why.
For the rest, if we still manage to get here with INVALID_PIPE on
VLV/CHV we will now get a WARN from the lower level functions and
can then actually investigate further.
v2: Leave the check in the BIOS related code (Jani)
Cc: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Currently we register the backlight device as soon as we register the
connector. That means we can get backlight requests from userspace
already before reading out the current modeset hardware state.
That means we don't yet know the current crtc->encoder->connector mapping,
which causes problems for VLV/CHV which need to know the current pipe in
order to figure out which BLC registers to poke. Currently we just
ignore such requests fairly deep in the backlight code which means the
backlight device brightness property will get out of sync with our
backlight.level and the actual hardware state.
Fix the problem by delaying the backlight device registration until the
entire modeset init has been performed. And we also move the
backlight unregisteration to happen as the first thing during the
modeset cleanup so that we also won't be bothered with userspace
backlight requested during teardown.
This is a real world problem on machines using systemd, because systemd,
for some reason, wants to restore the backlight to the level it used last
time. And that happens as soon as it sees the backlight device appearing
in the system. Sometimes the userspace access makes it through before
the modeset init, sometimes not.
v2: Do not lie to the user in the debug prints (Jani)
Include connector name in the prints (Jani)
Fix a typo in the commit message (Jani)
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
On VLV/CHV both pipes A and B have their own backlight control
registers. In order to correctly read out the current hardware state at
init we need to know which pipe is driving the eDP port. Pass that
information down from the eDP init code into the backlight code.
To determine the correct pipe we first look at which pipe is currently
configured in the port control register, if that look invalid we look
at which pipe's PPS is currently controlling the port, and if that
too looks invalid we just assume pipe A.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
On VLV/CHV when the display is off, we can't read out the current
backlight level from the hardware since we have no pipe to do so.
Currently we end up reading a bigus register due to passing
INVALID_PIPE to VLV_BLC_PWM_CTL().
Skip the entire .get_backlight() call if the backlight isn't enabled
according to backlight.enabled.
This problem can be reproduced simply by reading the backlight device
actual_brightness file while the display is off.
Cc: Jani Nikula <jani.nikula@intel.com>
Suggested-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
VLV/CHV have backlight controls only on pipes A and B. Bail out
without touching registers that don't exist, and print a warning.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Never trust (your interpretation of) the VBT. Regression from
commit 6dda730e55
Author: Jani Nikula <jani.nikula@intel.com>
Date: Tue Jun 24 18:27:40 2014 +0300
drm/i915: respect the VBT minimum backlight brightness
causing div by zero if VBT minimum brightness equals maximum brightness.
Despite my attempts I've failed in my detective work to figure out what
the root cause is. This is not the real fix, but we have to do
something.
Reported-by: Mike Auty <mike.auty@gmail.com>
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=86551
Cc: stable@vger.kernel.org (v3.17+)
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
SPT is always in the PCH override mode, and the bit MBZ. Only set
override on LPT.
v2: check for PCH version (Ville)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
So I've sent the first pull request to Dave and I expect his request
for a merge tree any second now ;-)
More seriously I have some pending patches for 3.19 that depend upon
both trees, hence backmerge. Conflicts are all trivial.
Conflicts:
drivers/gpu/drm/i915/i915_irq.c
drivers/gpu/drm/i915/intel_display.c
v2: Of course I've forgotten the fixup script for the silent conflict.
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Move the duplicated DIV_ROUND_CLOSEST_ULL macro into the intel_drv.h
header file so that it can be shared between intel_display.c
and intel_panel.c.
Signed-off-by: U. Artie Eoff <ullysses.a.eoff@intel.com>
Reviewed-By: Joe Konno <joe.konno@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Improper truncated integer division in the scale() function causes
actual_brightness != brightness. This (partial) work-around should be
sufficient for a majority of use-cases, but it is by no means a complete
solution.
TODO: Determine how best to scale "user" values to "hw" values, and
vice-versa, when the ranges are of different sizes. That would be a
buggy scenario even with this work-around.
The issue was introduced in the following (v3.17-rc1) commit:
6dda730 drm/i915: respect the VBT minimum backlight brightness
Note that for easier backporting this commit adds a duplicated macro.
A follow-up cleanup patch rectifies this for 3.18+
v2: (thanks to Chris Wilson) clarify commit message, use rounded division
macro
v3: -DIV_ROUND_CLOSEST() fails to build with CONFIG_X86_32=y. (Jani)
-Use DIV_ROUND_CLOSEST_ULL() instead. (Damien)
-v1 and v2 originally authored by Joe Konno.
Signed-off-by: U. Artie Eoff <ullysses.a.eoff@intel.com>
Cc: stable@vger.kernel.org
Reviewed-By: Joe Konno <joe.konno@intel.com>
[danvet: Add backporting note.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
SKL stage 1 patches still need polish so will likely miss the 3.18
merge window. We've decided to postpone to 3.19 so let's pull this in
to make patch merging and conflict handling easier.
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Originally the irq safe spinlock was required because of asle
interrupts. But since
commit 91a60f2071
Author: Jani Nikula <jani.nikula@intel.com>
Date: Thu Oct 31 18:55:48 2013 +0200
drm/i915: move opregion asle request handling to a work queue
there's no need for this any more. So switch to the simpler mutex.
v2: Cite the right commit, spotted by Jani.
Cc: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
- final bits (again) for the rotation support (Sonika Jindal)
- support bl_power in the intel backlight (Jani)
- vdd handling improvements from Ville
- i830M fixes from Ville
- piles of prep work all over to make skl enabling just plug in (Damien, Sonika)
- rename DP training defines to reflect latest edp standards, this touches all
drm drivers supporting DP (Sonika Jindal)
- cache edids during single detect cycle to avoid re-reading it for e.g. audio,
from Chris
- move w/a for registers which are stored in the hw context to the context init
code (Arun&Damien)
- edp panel power sequencer fixes, helps chv a lot (Ville)
- piles of other chv fixes all over
- much more paranoid pageflip handling with stall detection and better recovery
from Chris
- small things all over, as usual
* tag 'drm-intel-next-2014-09-05' of git://anongit.freedesktop.org/drm-intel: (114 commits)
drm/i915: Update DRIVER_DATE to 20140905
drm/i915: Decouple the stuck pageflip on modeset
drm/i915: Check for a stalled page flip after each vblank
drm/i915: Introduce a for_each_plane() macro
drm/i915: Rewrite ABS_DIFF() in a safer manner
drm/i915: Add comments explaining the vdd on/off functions
drm/i915: Move DP port disable to post_disable for pch platforms
drm/i915: Enable DP port earlier
drm/i915: Turn on panel power before doing aux transfers
drm/i915: Be more careful when picking the initial power sequencer pipe
drm/i915: Reset power sequencer pipe tracking when disp2d is off
drm/i915: Track which port is using which pipe's power sequencer
drm/i915: Fix edp vdd locking
drm/i915: Reset the HEAD pointer for the ring after writing START
drm/i915: Fix unsafe vma iteration in i915_drop_caches
drm/i915: init sprites with univeral plane init function
drm/i915: Check of !HAS_PCH_SPLIT() in PCH transcoder funcs
drm/i915: Use HAS_GMCH_DISPLAY un underrun reporting code
drm/i915: Use IS_BROADWELL() instead of IS_GEN8() in forcewake code
drm/i915: Don't call gen8_fbc_sw_flush() on chv
...
Chris has decided that enough is enough. It's time to fixup dev Vs
dev_priv. This is a modest contribution to the crusade.
v2: Still use INTEL_INFO(), for the (mythical!) case we want to hardcode
the info struct with defines (Chris)
Rename the macro argument from 'dev' to 'dev_priv' (Jani)
v3: Use names unlikely to be used as macro arguments (Chris)
Suggested-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Make backlight class sysfs brightness 0 value switch off the backlight
for connectors that have the backlight_power callback defined. For eDP,
this has the similar caveats regarding power savings as bl_power as only
the power sequencer backlight control is switched off.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed_by: Clinton Taylor <Clinton.A.Taylor@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Make backlight class sysfs bl_power a sub-state of backlight enabled, if
a backlight power connector callback is defined. It's up to the
connector callback to handle the sub-state, typically in a way that
respects panel power sequencing.
v2: Post the version that does not oops. *facepalm*.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed_by: Clinton Taylor <Clinton.A.Taylor@intel.com>
Tested_by: Clinton Taylor <Clinton.A.Taylor@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
BIOS or firmware can modify hardware state during suspend/resume,
for example on the Toshiba CB35 or Lenovo T400, so log a debug message
instead of a warning if the backlight is unexpectedly enabled.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=80930
Cc: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Scot Doyle <lkml14@scotdoyle.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Historically we've exposed the full backlight PWM duty cycle range to
the userspace, in the name of "mechanism, not policy". However, it turns
out there are both panels and board designs where there is a minimum
duty cycle that is required for proper operation. The minimum duty cycle
is available in the VBT.
The backlight class sysfs interface does not make any promises to the
userspace about the physical meaning of the range
0..max_brightness. Specifically there is no guarantee that 0 means off;
indeed for acpi_backlight 0 usually is not off, but the minimum
acceptable value.
Respect the minimum backlight, and expose the range acceptable to the
hardware as 0..max_brightness to the userspace via the backlight class
device; 0 means the minimum acceptable enabled value. To switch off the
backlight, the user must disable the encoder.
As a side effect, make the backlight class device max brightness and
physical PWM modulation frequency (i.e. max duty cycle)
independent. This allows a follow-up patch to virtualize the max value
exposed to the userspace.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
[danvet: s/BUG_ON/WARN_ON/]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This reverts commit 773875bfb6.
It is very much needed and the lack of dithering has been reported by
a large list of people with various gen2/3 hardware.
Also, the original patch was complete non-sense since the WARNING
backtraces in the references bugzilla are about
gmch_pfit.lvds_border_bits mismatch, not at all about the dither bit.
That one seems to work.
Cc: Jiri Kosina <jkosina@suse.cz>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Hans de Bruin <jmdebruin@xmsnet.nl>
Cc: stable@vger.kernel.org
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
commit c675949ec5
Author: Jani Nikula <jani.nikula@intel.com>
Date: Wed Apr 9 11:31:37 2014 +0300
drm/i915: do not setup backlight if not available according to VBT
caused a regression on machines with a misconfigured VBT. Add a quirk to
assert the presence of a controllable backlight. Use it to ignore the VBT
backlight presence check during backlight setup.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=79813
Tested-by: James Duley <jagduley@gmail.com>
Tested-by: Michael Mullin <masmullin@gmail.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Scot Doyle <lkml14@scotdoyle.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Cc: stable@vger.kernel.org # 3.15 only
[danvet: Add cc: stable because the regressing commit is in 3.15.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
For reasons I can't claim to fully understand gen4 seems to require
backlight duty cycle setting after the backlight has been enabled, or
else black screen follows. I don't have documentation for the correct
sequence on gen4 either. Confirmed on Dell Latitude D630 and MacBook4,1.
This fixes a regression introduced by
commit b35684b8fa
Author: Jani Nikula <jani.nikula@intel.com>
Date: Thu Nov 14 12:13:41 2013 +0200
drm/i915: do full backlight setup at enable time
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=75791
Reported-and-tested-by: mcy@lm7.fr
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=79423
Reported-and-tested-by: Marc Milgram <mmilgram@redhat.com>
Cc: Stable <stable@vger.kernel.org> # 3.14+
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Merge drm-fixes into drm-next.
Both i915 and radeon need this done for later patches.
Conflicts:
drivers/gpu/drm/drm_crtc_helper.c
drivers/gpu/drm/i915/i915_drv.h
drivers/gpu/drm/i915/i915_gem.c
drivers/gpu/drm/i915/i915_gem_execbuffer.c
drivers/gpu/drm/i915/i915_gem_gtt.c
For atomic, it will be quite necessary to not need to care so much
about locking order. And 'state' gives us a convenient place to stash a
ww_ctx for any sort of update that needs to grab multiple crtc locks.
Because we will want to eventually make locking even more fine grained
(giving locks to planes, connectors, etc), split out drm_modeset_lock
and drm_modeset_acquire_ctx to track acquired locks.
Atomic will use this to keep track of which locks have been acquired
in a transaction.
v1: original
v2: remove a few things not needed until atomic, for now
v3: update for v3 of connection_mutex patch..
v4: squash in docbook
v5: doc tweaks/fixes
Signed-off-by: Rob Clark <robdclark@gmail.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
After the split-out of crtc locks from the big mode_config.mutex
there's still two major areas it protects:
- Various connector probe states, like connector->status, EDID
properties, probed mode lists and similar information.
- The links from connector->encoder and encoder->crtc and other
modeset-relevant connector state (e.g. properties which control the
panel fitter).
The later is used by modeset operations. But they don't really care
about the former since it's allowed to e.g. enable a disconnected VGA
output or with a mode not in the probed list.
Thus far this hasn't been a problem, but for the atomic modeset
conversion Rob Clark needs to convert all modeset relevant locks into
w/w locks. This is required because the order of acquisition is
determined by how userspace supplies the atomic modeset data. This has
run into troubles in the detect path since the i915 load detect code
needs _both_ protections offered by the mode_config.mutex: It updates
probe state and it needs to change the modeset configuration to enable
the temporary load detect pipe.
The big deal here is that for the probe/detect users of this lock a
plain mutex fits best, but for atomic modesets we really want a w/w
mutex. To fix this lets split out a new connection_mutex lock for the
modeset relevant parts.
For simplicity I've decided to only add one additional lock for all
connector/encoder links and modeset configuration states. We have
piles of different modeset objects in addition to those (like bridges
or panels), so adding per-object locks would be much more effort.
Also, we're guaranteed (at least for now) to do a full modeset if we
need to acquire this lock. Which means that fine-grained locking is
fairly irrelevant compared to the amount of time the full modeset will
take.
I've done a full audit, and there's just a few things that justify
special focus:
- Locking in drm_sysfs.c is almost completely absent. We should
sprinkle mode_config.connection_mutex over this file a bit, but
since it already lacks mode_config.mutex this patch wont make the
situation any worse. This is material for a follow-up patch.
- omap has a omap_framebuffer_flush function which walks the
connector->encoder->crtc links and is called from many contexts.
Some look like they don't acquire mode_config.mutex, so this is
already racy. Again fixing this is material for a separate patch.
- The radeon hot_plug function to retrain DP links looks at
connector->dpms. Currently this happens without any locking, so is
already racy. I think radeon_hotplug_work_func should gain
mutex_lock/unlock calls for the mode_config.connection_mutex.
- Same applies to i915's intel_dp_hot_plug. But again, this is already
racy.
- i915 load_detect code needs to acquire this lock. Which means the
w/w dance due to Rob's work will be nicely contained to _just_ this
function.
I've added fixme comments everywhere where it looks suspicious but in
the sysfs code. After a quick irc discussion with Dave Airlie it
sounds like the lack of locking in there is due to sysfs cleanup fun
at module unload.
v1: original (only compile tested)
v2: missing mutex_init(), etc (from Rob Clark)
v3: i915 needs more care in the conversion:
- Protect the edp pp logic with the connection_mutex.
- Use connection_mutex in the backlight code due to
get_pipe_from_connector.
- Use drm_modeset_lock_all in suspend/resume paths.
- Update lock checks in the overlay code.
Cc: Alex Deucher <alexdeucher@gmail.com>
Cc: Rob Clark <robdclark@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Rob Clark <robdclark@gmail.com>
Somehow a few functions have been dropped in the middle of backlight
code. Move them around. No functional changes.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
When we set backlight on behalf of ACPI opregion, we will convert the
backlight value in the 0-255 range defined in opregion to the actual
hardware level. Commit 22505b82a2 (drm/i915: avoid brightness overflow
when doing scale) is meant to fix the overflow problem when doing the
conversion, but it also caused a problem that the converted hardware
level doesn't quite represent the intended value: say user wants maximum
backlight level(255 in opregion's range), then we will calculate the
actual hardware level to be: level = freq / max * level, where freq is
the hardware's max backlight level(937 on an user's box), and max and
level are all 255. The converted value should be 937 but the above
calculation will yield 765.
To fix this issue, just use 64 bits to do the calculation to keep the
precision and avoid overflow at the same time.
Buglink: https://bugzilla.kernel.org/show_bug.cgi?id=72491
Reported-by: Nico Schottelius <nico-bugzilla.kernel.org@schottelius.org>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@vger.kernel.org
Signed-off-by: Aaron Lu <aaron.lu@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
drm-intel-next-2014-04-16:
- vlv infoframe fixes from Jesse
- dsi/mipi fixes from Shobhit
- gen8 pageflip fixes for LRI/SRM from Damien
- cmd parser fixes from Brad Volkin
- some prep patches for CHV, DRRS, ...
- and tons of little things all over
drm-intel-next-2014-04-04:
- cmd parser for gen7 but only in enforcing and not yet granting mode - the
batch copying stuff is still missing. Also performance is a bit ... rough
(Brad Volkin + OACONTROL fix from Ken).
- deprecate UMS harder (i.e. CONFIG_BROKEN)
- interrupt rework from Paulo Zanoni
- runtime PM support for bdw and snb, again from Paulo
- a pile of refactorings from various people all over the place to prep for new
stuff (irq reworks, power domain polish, ...)
drm-intel-next-2014-04-04:
- cmd parser for gen7 but only in enforcing and not yet granting mode - the
batch copying stuff is still missing. Also performance is a bit ... rough
(Brad Volkin + OACONTROL fix from Ken).
- deprecate UMS harder (i.e. CONFIG_BROKEN)
- interrupt rework from Paulo Zanoni
- runtime PM support for bdw and snb, again from Paulo
- a pile of refactorings from various people all over the place to prep for new
stuff (irq reworks, power domain polish, ...)
Conflicts:
drivers/gpu/drm/i915/i915_gem_context.c
Apparently we really only need this when the pfit is enabled, at least
I couldn't dicern any difference here. Furthermore the hacks we have
to reconstruct this bit is a bit glaring, and probably only works
because we can't move the lvds port to any other pipe than pipe B on
gen2/3.
So let's just rip this out.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=77137 (the LVDS
WARNING log, not the main "VGA can't be turned on" issue).
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
