Add a user-visible attribute for the number of alternate modes available
in a partner. This allows userspace to determine whether there are any
remaining alternate modes left to be registered by the kernel driver. It
can begin executing any policy state machine after all available
alternate modes have been registered with the connector class framework.
This value is set to "-1" initially, signifying that a valid number of
alternate modes haven't been set for the partner.
Also add a sysfs file which exposes this attribute. The file remains
hidden as long as the attribute value is -1.
Cc: Benson Leung <bleung@chromium.org>
Cc: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Prashant Malani <pmalani@chromium.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20201116201150.2919178-3-pmalani@chromium.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
retval may be reassigned to 0 after max3421_of_vbus_en_pin(),
if allocate memory failed after this, max3421_probe() cann't
return ENOMEM, fix this by moving assign retval afther max3421_probe().
Fixes: 721fdc83b3 ("usb: max3421: Add devicetree support")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20201117061500.3454223-1-yangyingliang@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Thunderbolt cable generation bits received as a part of Thunderbolt 3 cable
discover mode VDO needs to be configured for Thunderbolt rounded and
non-rounded cable support in the Thunderbolt alternate mode.
Signed-off-by: Utkarsh Patel <utkarsh.h.patel@intel.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
--
Changes in v2:
- No change.
--
Link: https://lore.kernel.org/r/20201113202503.6559-4-utkarsh.h.patel@intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The ehci-mxc driver was only used by i.MX non-DT platforms.
Since 5.10-rc1, i.MX has been converted to a DT-only platform and all
board files are gone.
Remove the ehci-mxc driver as there are no more users at all.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Link: https://lore.kernel.org/r/20201113171231.2205-1-festevam@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Renesas R-Car and RZ/G SoCs have a firmware download mode over USB.
However, on reset a banner string is transmitted out which is not expected
to be echoed back and will corrupt the protocol.
Cc: stable <stable@vger.kernel.org>
Acked-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: Chris Brandt <chris.brandt@renesas.com>
Link: https://lore.kernel.org/r/20201111131209.3977903-1-chris.brandt@renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the ucsi power supply goes online/offline, and when the
power levels change, the power supply class needs to be
notified so it can inform the user space.
Fixes: 992a60ed0d ("usb: typec: ucsi: register with power_supply class")
Cc: stable@vger.kernel.org
Reported-and-tested-by: Vladimir Yerilov <openmindead@gmail.com>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20201110120547.67922-1-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since commit 4b563a0666 ("ARM: imx: Remove imx21 support") the imx21
SoC is no longer supported.
Get rid of its USB driver too, which is now unused.
Acked-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Link: https://lore.kernel.org/r/20201109210813.21382-1-festevam@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When usb_stor_bulk_transfer_sglist() returns with USB_STOR_XFER_ERROR, it
returns without writing to its parameter *act_len.
Further, the two callers of usb_stor_bulk_transfer_sglist():
usb_stor_bulk_srb() and
usb_stor_bulk_transfer_sg(),
use the passed variable partial without checking the return value. Hence,
the uninitialized value of partial is then used in the further execution
of those two functions.
Clang-analyzer detects this potential control and data flow and warns:
drivers/usb/storage/transport.c:469:40:
warning: The right operand of '-' is a garbage value
[clang-analyzer-core.UndefinedBinaryOperatorResult]
scsi_set_resid(srb, scsi_bufflen(srb) - partial);
^
drivers/usb/storage/transport.c:495:15:
warning: Assigned value is garbage or undefined
[clang-analyzer-core.uninitialized.Assign]
length_left -= partial;
^
When a transfer error occurs, the *act_len value is probably ignored by the
higher layers. But it won't hurt to set it to a valid number, just in case.
For the two early-return paths in usb_stor_bulk_transfer_sglist(), the
amount of data transferred is 0. So if act_len is not NULL, set *act_len
to 0 in those paths. That makes clang-analyzer happy.
Proposal was discussed in this mail thread:
https://lore.kernel.org/linux-usb/alpine.DEB.2.21.2011112146110.13119@felia/
Reviewed-by: Nathan Chancellor <natechancellor@gmail.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Lukas Bulwahn <lukas.bulwahn@gmail.com>
Link: https://lore.kernel.org/r/20201112191255.13372-1-lukas.bulwahn@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The "fallthrough" pseudo-keyword was added as a portable way to denote
intentional fallthrough. Clang will still warn on cases where there is a
fallthrough to an immediate break. Add explicit breaks for those cases.
Reviewed-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Nick Desaulniers <ndesaulniers@google.com>
Link: https://lore.kernel.org/r/20201111014716.260633-1-ndesaulniers@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
pm_runtime_get_sync() will increment pm usage at first and it
will resume the device later. We should decrease the usage count
whetever it succeeded or failed(maybe runtime of the device has
error, or device is in inaccessible state, or other error state).
If we do not call put operation to decrease the reference, it will
result in reference leak in xhci_histb_probe. Moreover, this
device cannot enter the idle state and always stay busy or other
non-idle state later. So we fixed it by jumping to error handling
branch.
Fixes: c508f41da0 ("xhci: hisilicon: support HiSilicon STB xHCI host controller")
Signed-off-by: Zhang Qilong <zhangqilong3@huawei.com>
Link: https://lore.kernel.org/r/20201106122221.2304528-1-zhangqilong3@huawei.com
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 2d30e408a2.
On Beaglebone Black, where each interface has 2 children:
musb-dsps 47401c00.usb: can't request region for resource [mem 0x47401800-0x474019ff]
musb-hdrc musb-hdrc.1: musb_init_controller failed with status -16
musb-hdrc: probe of musb-hdrc.1 failed with error -16
musb-dsps 47401400.usb: can't request region for resource [mem 0x47401000-0x474011ff]
musb-hdrc musb-hdrc.0: musb_init_controller failed with status -16
musb-hdrc: probe of musb-hdrc.0 failed with error -16
Before, devm_ioremap_resource() was called on "dev" ("musb-hdrc.0" or
"musb-hdrc.1"), after it is called on "&pdev->dev" ("47401400.usb" or
"47401c00.usb"), leading to a duplicate region request, which fails.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Fixes: 2d30e408a2 ("usb: musb: convert to devm_platform_ioremap_resource_byname")
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20201112135900.3822599-1-geert+renesas@glider.be
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here's a fix for a long-standing issue with the cyberjack driver and
some new device ids.
All have been in linux-next with no reported issues.
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQQHbPq+cpGvN/peuzMLxc3C7H1lCAUCX6VuxQAKCRALxc3C7H1l
CMKEAQD+X/sKaJ9n+HxsCOn3QQ2qVY7XjhXjLgGfl8EsMNbHsgEAnF/AHqs6A2xm
Ye9oOegkdWTSQ9ncI/uFr63V5JmKbQA=
=70V3
-----END PGP SIGNATURE-----
Merge tag 'usb-serial-5.10-rc3' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-linus
Johan writes:
USB-serial fixes for 5.10-rc3
Here's a fix for a long-standing issue with the cyberjack driver and
some new device ids.
All have been in linux-next with no reported issues.
* tag 'usb-serial-5.10-rc3' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial:
USB: serial: option: add Telit FN980 composition 0x1055
USB: serial: option: add LE910Cx compositions 0x1203, 0x1230, 0x1231
USB: serial: cyberjack: fix write-URB completion race
USB: serial: option: add Quectel EC200T module support
pm_runtime_get_sync() will increment pm usage at first and it
will resume the device later. If runtime of the device has
error or device is in inaccessible state(or other error state),
resume operation will fail. If we do not call put operation to
decrease the reference, the result is that this device cannot
enter the idle state and always stay busy or other non-idle
state.
Fixes: 249fa8217b ("USB: Add driver to control USB fast charge for iOS devices")
Signed-off-by: Zhang Qilong <zhangqilong3@huawei.com>
Link: https://lore.kernel.org/r/20201102022650.67115-1-zhangqilong3@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix the following sparse warning:
drivers/usb/misc/brcmstb-usb-pinmap.c:219:6: warning: symbol 'sync_all_pins' was not declared. Should it be static?
The sync_all_pins has only call site within brcmstb-usb-pinmap.c
It should be static
Fixes: 517c4c44b3 ("usb: Add driver to allow any GPIO to be used for 7211 USB signals")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zou Wei <zou_wei@huawei.com>
Link: https://lore.kernel.org/r/1604050097-91302-1-git-send-email-zou_wei@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some/many PPMs are simply clearing the change bitfield when a
notification on a port is acknowledge. Unfortunately, doing so means
that any changes between the GET_CONNECTOR_STATUS and ACK_CC_CI commands
is simply lost.
Work around this by re-fetching the connector status afterwards. We can
then infer any changes that we see have happened but that may not be
respresented in the change bitfield.
We end up with the following actions:
1. UCSI_GET_CONNECTOR_STATUS, store result, update unprocessed_changes
2. UCSI_GET_CAM_SUPPORTED, discard result
3. ACK connector change
4. UCSI_GET_CONNECTOR_STATUS, store result
5. Infere lost changes by comparing UCSI_GET_CONNECTOR_STATUS results
6. If PPM reported a new change, then restart in order to ACK
7. Process everything as usual.
The worker is also changed to re-schedule itself if a new change
notification happened while it was running.
Doing this fixes quite commonly occurring issues where e.g. the UCSI
power supply would remain online even thought the ThunderBolt cable was
unplugged.
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Benjamin Berg <bberg@redhat.com>
Link: https://lore.kernel.org/r/20201009144047.505957-3-benjamin@sipsolutions.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Normal commands may be reporting that a connector has changed. Always
call the usci_connector_change handler and let it take care of
scheduling the work when needed.
Doing this makes the ACPI code path identical to the CCG one.
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Benjamin Berg <bberg@redhat.com>
Link: https://lore.kernel.org/r/20201009144047.505957-2-benjamin@sipsolutions.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The write-URB busy flag was being cleared before the completion handler
was done with the URB, something which could lead to corrupt transfers
due to a racing write request if the URB is resubmitted.
Fixes: 507ca9bc04 ("[PATCH] USB: add ability for usb-serial drivers to determine if their write urb is currently being used.")
Cc: stable <stable@vger.kernel.org> # 2.6.13
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
In Bugzilla #208257, Julien Humbert reports that a 32-GB Kingston
flash drive spontaneously disconnects and reconnects, over and over.
Testing revealed that disabling Link Power Management for the drive
fixed the problem.
This patch adds a quirk entry for that drive to turn off LPM permanently.
CC: Hans de Goede <jwrdegoede@fedoraproject.org>
CC: <stable@vger.kernel.org>
Reported-and-tested-by: Julien Humbert <julroy67@gmail.com>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20201102145821.GA1478741@rowland.harvard.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The devm_ioremap() function doesn't return error pointers, it returns
NULL on error.
Fixes: 517c4c44b3 ("usb: Add driver to allow any GPIO to be used for 7211 USB signals")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://lore.kernel.org/r/20201102075655.GA4163205@mwanda
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Nothing major as of yet, we're adding support for Intel Alder Lake-S
in dwc3, together with a few fixes that are quite important (memory
leak in raw-gadget, probe crashes in goku_udc, and so on).
Signed-off-by: Felipe Balbi <balbi@kernel.org>
-----BEGIN PGP SIGNATURE-----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=9Vi/
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-v5.10-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-linus
Felipe writes:
USB: fixes for v5.10-rc2
Nothing major as of yet, we're adding support for Intel Alder Lake-S
in dwc3, together with a few fixes that are quite important (memory
leak in raw-gadget, probe crashes in goku_udc, and so on).
Signed-off-by: Felipe Balbi <balbi@kernel.org>
* tag 'fixes-for-v5.10-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb:
usb: raw-gadget: fix memory leak in gadget_setup
usb: dwc2: Avoid leaving the error_debugfs label unused
usb: dwc3: ep0: Fix delay status handling
usb: gadget: fsl: fix null pointer checking
usb: gadget: goku_udc: fix potential crashes in probe
usb: dwc3: pci: add support for the Intel Alder Lake-S
The biggest fix is changing endpoint configuration method to
avoid FIFO overflow at multiple endpoints situation.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEDaZUZmFxRG/wNThrSFkpgVDWcbsFAl+bjLUACgkQSFkpgVDW
cbtjCAgAwvFT8C6NtyKk3LthQ2A9B8YLnoXgOHWY2io05+DRCG2GgLr4SudZtLvf
HzRqkijF0zfrSSwXzsFlE1JUUK9VBNhaGg0NXJNCkQhL8PzFhbmI4nfuPi+Yh9K7
nH8nS46sR2CIBBngaH/3pXa05Zrntas+xLGRBDIIWsDJAyP2sB4M5DQrMxHcpTHK
ty2wxggC6V1ZOV/FzYj67jh8gIHoPkHRyTS60YqUYUDuxpgRO2rwrtnwb85OSG2q
usEKMNf6eAMu5Kj42Ie+SymTyXrLyitzWviRmmnk9rqFF9jiD2oI8NqzXQxSpmIQ
+W4J2WbodWjsxqNnsVK2DpcIffJStA==
=6USD
-----END PGP SIGNATURE-----
Merge tag 'usb-v5.10-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/peter.chen/usb into usb-linus
Peter writes:
4 bug fixes for Cadence 3 driver.
The biggest fix is changing endpoint configuration method to
avoid FIFO overflow at multiple endpoints situation.
* tag 'usb-v5.10-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/peter.chen/usb:
usb: cdns3: gadget: own the lock wrongly at the suspend routine
usb: cdns3: Fix on-chip memory overflow issue
usb: cdns3: gadget: suspicious implicit sign extension
usb: cdns3: Variable 'length' set but not used
When the system goes to suspend, if the controller is at device mode with
cable connecting to host, the call stack is: cdns3_suspend->
cdns3_gadget_suspend -> cdns3_disconnect_gadget, after cdns3_disconnect_gadget
is called, it owns lock wrongly, it causes the system being deadlock after
resume due to at cdns3_device_thread_irq_handler, it tries to get the lock,
but can't get it forever.
To fix it, we delete the unlock-lock operations at cdns3_disconnect_gadget,
and do it at the caller.
Fixes: b1234e3b3b ("usb: cdns3: add runtime PM support")
Acked-by: Pawel Laszczak <pawell@cadence.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Patch fixes issue caused setting On-chip memory overflow bit in usb_sts
register. The issue occurred because EP_CFG register was set twice
before USB_STS.CFGSTS was set. Every write operation on EP_CFG.BUFFERING
causes that controller increases internal counter holding the number
of reserved on-chip buffers. First time this register was updated in
function cdns3_ep_config before delegating SET_CONFIGURATION request
to class driver and again it was updated when class wanted to enable
endpoint. This patch fixes this issue by configuring endpoints
enabled by class driver in cdns3_gadget_ep_enable and others just
before status stage.
Cc: stable@vger.kernel.org#v5.8+
Fixes: 7733f6c32e ("usb: cdns3: Add Cadence USB3 DRD Driver")
Reported-and-tested-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Pawel Laszczak <pawell@cadence.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
The code:
trb->length = cpu_to_le32(TRB_BURST_LEN(priv_ep->trb_burst_size)
| TRB_LEN(length));
TRB_BURST_LEN(priv_ep->trb_burst_size) may be overflow for int 32 if
priv_ep->trb_burst_size is equal or larger than 0x80;
Below is the Coverity warning:
sign_extension: Suspicious implicit sign extension: priv_ep->trb_burst_size
with type u8 (8 bits, unsigned) is promoted in priv_ep->trb_burst_size << 24
to type int (32 bits, signed), then sign-extended to type unsigned long
(64 bits, unsigned). If priv_ep->trb_burst_size << 24 is greater than 0x7FFFFFFF,
the upper bits of the result will all be 1.
To fix it, it needs to add an explicit cast to unsigned int type for ((p) << 24).
Reviewed-by: Jun Li <jun.li@nxp.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Creating debugfs files while loding the spin_lock_irqsave(xhci->lock)
creates a lock dependecy that could possibly deadlock.
Lockdep warns:
=====================================================
WARNING: HARDIRQ-safe -> HARDIRQ-unsafe lock order detected
5.10.0-rc1pdx86+ #8 Not tainted
-----------------------------------------------------
systemd-udevd/386 [HC0[0]:SC0[0]:HE0:SE1] is trying to acquire:
ffffffffb1a94038 (pin_fs_lock){+.+.}-{2:2}, at: simple_pin_fs+0x22/0xa0
and this task is already holding:
ffff9e7b87fbc430 (&xhci->lock){-.-.}-{2:2}, at: xhci_alloc_streams+0x5f9/0x810
which would create a new lock dependency:
(&xhci->lock){-.-.}-{2:2} -> (pin_fs_lock){+.+.}-{2:2}
Create the files a bit later after lock is released.
Fixes: 673d746836 ("usb: xhci: add debugfs support for ep with stream")
CC: Li Jun <jun.li@nxp.com>
Reported-by: Hans de Goede <hdegoede@redhat.com>
Reported-by: Mike Galbraith <efault@gmx.de>
Tested-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20201028203124.375344-4-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On some platform of AMD, S3 fails with HCE and SRE errors. To fix this,
need to disable a bit which is enable in sparse controller.
Cc: stable@vger.kernel.org #v4.19+
Signed-off-by: Sanket Goswami <Sanket.Goswami@amd.com>
Signed-off-by: Sandeep Singh <sandeep.singh@amd.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20201028203124.375344-3-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
An incorrect sizeof() is being used, sizeof(rhub->ports) is not
correct, it should be sizeof(*rhub->ports). This bug did not
cause any issues because it just so happens the sizes are the same.
Fixes: bcaa9d5c59 ("xhci: Create new structures to store xhci port information")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20201028203124.375344-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
chip->port_type and chip->pwr_opmode are enums and when GCC considers them
as unsigned, the conditions are never met.
This patch takes advantage of the ret variable and fixes the following
warnings:
drivers/usb/typec/stusb160x.c:548 stusb160x_get_fw_caps() warn: unsigned 'chip->port_type' is never less than zero.
drivers/usb/typec/stusb160x.c:570 stusb160x_get_fw_caps() warn: unsigned 'chip->pwr_opmode' is never less than zero.
Fixes: da0cb63100 ("usb: typec: add support for STUSB160x Type-C controller family")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Link: https://lore.kernel.org/r/20201028163309.12878-1-amelie.delaunay@st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When stusb160x driver is built as a module, no modalias information is
available, and it prevents the module to be loaded by udev.
Add MODULE_DEVICE_TABLE() to fix this issue.
Fixes: da0cb63100 ("usb: typec: add support for STUSB160x Type-C controller family")
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Link: https://lore.kernel.org/r/20201028151703.31195-1-amelie.delaunay@st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
From: Bastien Nocera <hadess@hadess.net>
Contrary to the comment above the id table, we didn't implement a match
function. This meant that every single Apple device that was already
plugged in to the computer would have its device driver reprobed
when the apple-mfi-fastcharge driver was loaded, eg. the SD card reader
could be reprobed when the apple-mfi-fastcharge after pivoting root
during boot up and the module became available.
Make sure that the driver probe isn't being run for unsupported
devices by adding a match function that checks the product ID, in
addition to the id_table checking the vendor ID.
Link: https://bugzilla.redhat.com/show_bug.cgi?id=1878347
Link: https://lore.kernel.org/linux-usb/CAE3RAxt0WhBEz8zkHrVO5RiyEOasayy1QUAjsv-pB0fAbY1GSw@mail.gmail.com/
Fixes: 249fa8217b ("USB: Add driver to control USB fast charge for iOS devices")
Cc: <stable@vger.kernel.org> # 5.8
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Alan Stern <stern@rowland.harvard.edu>
[m.v.b: Add Link and Reported-by tags to the commit message]
Reported-by: Pany <pany@fedoraproject.org>
Tested-by: Pan (Pany) YUAN <pany@fedoraproject.org>
Tested-by: Bastien Nocera <hadess@hadess.net>
Signed-off-by: Bastien Nocera <hadess@hadess.net>
Signed-off-by: M. Vefa Bicakci <m.v.b@runbox.com>
Link: https://lore.kernel.org/r/20201022135521.375211-3-m.v.b@runbox.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
From: Bastien Nocera <hadess@hadess.net>
When a USB device driver has both an id_table and a match() function, make
sure to check both to find a match, first matching the id_table, then
checking the match() function.
This makes it possible to have module autoloading done through the
id_table when devices are plugged in, before checking for further
device eligibility in the match() function.
Cc: <stable@vger.kernel.org> # 5.8
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Alan Stern <stern@rowland.harvard.edu>
Co-developed-by: M. Vefa Bicakci <m.v.b@runbox.com>
Tested-by: Bastien Nocera <hadess@hadess.net>
Signed-off-by: Bastien Nocera <hadess@hadess.net>
Signed-off-by: M. Vefa Bicakci <m.v.b@runbox.com>
Tested-by: Pan (Pany) YUAN <pany@fedoraproject.org>
Link: https://lore.kernel.org/r/20201022135521.375211-2-m.v.b@runbox.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the function platform_get_irq() failed, the negative value
returned will not be detected here. So fix error handling in
tegra_ehci_probe().
Fixes: 79ad3b5add ("usb: host: Add EHCI driver for NVIDIA Tegra SoCs")
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Tang Bin <tangbin@cmss.chinamobile.com>
Link: https://lore.kernel.org/r/20201026090657.49988-1-tangbin@cmss.chinamobile.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The typec_register_port() function doesn't return NULL, it returns error
pointers.
Fixes: da0cb63100 ("usb: typec: add support for STUSB160x Type-C controller family")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20201023114017.GE18329@kadam
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Current tcpm_detach() only reset hard_reset_count if port->attached
is true, this may cause this counter clear is missed if the CC
disconnect event is generated after tcpm_port_reset() is done
by other events, e.g. VBUS off comes first before CC disconect for
a power sink, in that case the first tcpm_detach() will only clear
port->attached flag but leave hard_reset_count there because
tcpm_port_is_disconnected() is still false, then later tcpm_detach()
by CC disconnect will directly return due to port->attached is cleared,
finally this will result tcpm will not try hard reset or error recovery
for later attach.
ChiYuan reported this issue on his platform with below tcpm trace:
After power sink session setup after hard reset 2 times, detach
from the power source and then attach:
[ 4848.046358] VBUS off
[ 4848.046384] state change SNK_READY -> SNK_UNATTACHED
[ 4848.050908] Setting voltage/current limit 0 mV 0 mA
[ 4848.050936] polarity 0
[ 4848.052593] Requesting mux state 0, usb-role 0, orientation 0
[ 4848.053222] Start toggling
[ 4848.086500] state change SNK_UNATTACHED -> TOGGLING
[ 4848.089983] CC1: 0 -> 0, CC2: 3 -> 3 [state TOGGLING, polarity 0, connected]
[ 4848.089993] state change TOGGLING -> SNK_ATTACH_WAIT
[ 4848.090031] pending state change SNK_ATTACH_WAIT -> SNK_DEBOUNCED @200 ms
[ 4848.141162] CC1: 0 -> 0, CC2: 3 -> 0 [state SNK_ATTACH_WAIT, polarity 0, disconnected]
[ 4848.141170] state change SNK_ATTACH_WAIT -> SNK_ATTACH_WAIT
[ 4848.141184] pending state change SNK_ATTACH_WAIT -> SNK_UNATTACHED @20 ms
[ 4848.163156] state change SNK_ATTACH_WAIT -> SNK_UNATTACHED [delayed 20 ms]
[ 4848.163162] Start toggling
[ 4848.216918] CC1: 0 -> 0, CC2: 0 -> 3 [state TOGGLING, polarity 0, connected]
[ 4848.216954] state change TOGGLING -> SNK_ATTACH_WAIT
[ 4848.217080] pending state change SNK_ATTACH_WAIT -> SNK_DEBOUNCED @200 ms
[ 4848.231771] CC1: 0 -> 0, CC2: 3 -> 0 [state SNK_ATTACH_WAIT, polarity 0, disconnected]
[ 4848.231800] state change SNK_ATTACH_WAIT -> SNK_ATTACH_WAIT
[ 4848.231857] pending state change SNK_ATTACH_WAIT -> SNK_UNATTACHED @20 ms
[ 4848.256022] state change SNK_ATTACH_WAIT -> SNK_UNATTACHED [delayed20 ms]
[ 4848.256049] Start toggling
[ 4848.871148] VBUS on
[ 4848.885324] CC1: 0 -> 0, CC2: 0 -> 3 [state TOGGLING, polarity 0, connected]
[ 4848.885372] state change TOGGLING -> SNK_ATTACH_WAIT
[ 4848.885548] pending state change SNK_ATTACH_WAIT -> SNK_DEBOUNCED @200 ms
[ 4849.088240] state change SNK_ATTACH_WAIT -> SNK_DEBOUNCED [delayed200 ms]
[ 4849.088284] state change SNK_DEBOUNCED -> SNK_ATTACHED
[ 4849.088291] polarity 1
[ 4849.088769] Requesting mux state 1, usb-role 2, orientation 2
[ 4849.088895] state change SNK_ATTACHED -> SNK_STARTUP
[ 4849.088907] state change SNK_STARTUP -> SNK_DISCOVERY
[ 4849.088915] Setting voltage/current limit 5000 mV 0 mA
[ 4849.088927] vbus=0 charge:=1
[ 4849.090505] state change SNK_DISCOVERY -> SNK_WAIT_CAPABILITIES
[ 4849.090828] pending state change SNK_WAIT_CAPABILITIES -> SNK_READY @240 ms
[ 4849.335878] state change SNK_WAIT_CAPABILITIES -> SNK_READY [delayed240 ms]
this patch fix this issue by clear hard_reset_count at any cases
of cc disconnect, í.e. don't check port->attached flag.
Fixes: 4b4e02c831 ("typec: tcpm: Move out of staging")
Cc: stable@vger.kernel.org
Reported-and-tested-by: ChiYuan Huang <cy_huang@richtek.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Li Jun <jun.li@nxp.com>
Link: https://lore.kernel.org/r/1602500592-3817-1-git-send-email-jun.li@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit a4e7279cd1 ("cdc-acm: introduce a cool down") is causing
regression if there is some USB error, such as -EPROTO.
This has been reported on some samples of the Odroid-N2 using the Combee II
Zibgee USB dongle.
> struct acm *acm = container_of(work, struct acm, work)
is incorrect in case of a delayed work and causes warnings, usually from
the workqueue:
> WARNING: CPU: 0 PID: 0 at kernel/workqueue.c:1474 __queue_work+0x480/0x528.
When this happens, USB eventually stops working completely after a while.
Also the ACM_ERROR_DELAY bit is never set, so the cooldown mechanism
previously introduced cannot be triggered and acm_submit_read_urb() is
never called.
This changes makes the cdc-acm driver use a single delayed work, fixing the
pointer arithmetic in acm_softint() and set the ACM_ERROR_DELAY when the
cooldown mechanism appear to be needed.
Fixes: a4e7279cd1 ("cdc-acm: introduce a cool down")
Cc: Oliver Neukum <oneukum@suse.com>
Reported-by: Pascal Vizeli <pascal.vizeli@nabucasa.com>
Acked-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Link: https://lore.kernel.org/r/20201019170702.150534-1-jbrunet@baylibre.com
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
fsl_usb2_device_register() should stop init if dma_set_mask() return
error.
Fixes: cae0586104 ("drivers/usb/host: fsl: Set DMA_MASK of usb platform device")
Reviewed-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
Link: https://lore.kernel.org/r/20201010060308.33693-1-ran.wang_1@nxp.com
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is a common comment marked, instead, with kernel-doc
notation.
Also, some identifiers have different names between their
prototypes and the kernel-doc markup.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Acked-by: Felipe Balbi <balbi@kernel.org>
Link: https://lore.kernel.org/r/0b964be3884def04fcd20ea5c12cb90d0014871c.1603469755.git.mchehab+huawei@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
These variables are enums but in this situation GCC will treat them as
unsigned so the conditions are never true.
Fixes: da0cb63100 ("usb: typec: add support for STUSB160x Type-C controller family")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://lore.kernel.org/r/20201023112412.GD282278@mwanda
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently there's a KCOV remote coverage collection section in
__usb_hcd_giveback_urb(). Initially that section was added based on the
assumption that usb_hcd_giveback_urb() can only be called in interrupt
context as indicated by a comment before it. This is what happens when
syzkaller is fuzzing the USB stack via the dummy_hcd driver.
As it turns out, it's actually valid to call usb_hcd_giveback_urb() in task
context, provided that the caller turned off the interrupts; USB/IP does
exactly that. This can lead to a nested KCOV remote coverage collection
sections both trying to collect coverage in task context. This isn't
supported by KCOV, and leads to a WARNING.
Change __usb_hcd_giveback_urb() to only call kcov_remote_*() callbacks
when it's being executed in a softirq. As the result, the coverage from
USB/IP related usb_hcd_giveback_urb() calls won't be collected, but the
WARNING is fixed.
A potential future improvement would be to support nested remote coverage
collection sections, but this patch doesn't address that.
Reviewed-by: Dmitry Vyukov <dvyukov@google.com>
Acked-by: Marco Elver <elver@google.com>
Signed-off-by: Andrey Konovalov <andreyknvl@google.com>
Link: https://lore.kernel.org/r/f3a7a153f0719cb53ec385b16e912798bd3e4cf9.1602856358.git.andreyknvl@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
No one is calling this function, so it's pointless to keep around as it
is triggering automated scanning tools to try to fix up the problems
with it using in_interrupt().
So delete the thing.
Reported-by: Thomas Gleixner <tglx@linutronix.de>
Reported-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Reported-by: Ahmed S. Darwish <a.darwish@linutronix.de>
Reviewed-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Link: https://lore.kernel.org/r/20201028113107.2007742-1-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The usage of in_interrupt() in drivers is phased out for various reasons.
xhci_set_hc_event_deq() has an !in_interrupt() check which is pointless
because the function is only invoked from xhci_mem_init() which is clearly
task context as it does GFP_KERNEL allocations. Remove it.
xhci_urb_enqueue() prints a debug message if an URB is submitted after the
underlying hardware was suspended. But that warning is only issued when
in_interrupt() is true, which makes no sense. Simply return -ESHUTDOWN and
be done with it.
Signed-off-by: Ahmed S. Darwish <a.darwish@linutronix.de>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Mathias Nyman <mathias.nyman@intel.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: linux-usb@vger.kernel.org
Link: https://lore.kernel.org/r/20201019101110.148631116@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The usage of in_interrupt() in drivers is phased out and Linus clearly
requested that code which changes behaviour depending on context should
either be separated or the context be conveyed in an argument passed by the
caller, which usually knows the context.
usbip_recv() uses in_interrupt() to conditionally print context information
for debugging messages. The value is zero as the function is only called
from various *_rx_loop() kthread functions. Remove it.
Signed-off-by: Ahmed S. Darwish <a.darwish@linutronix.de>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Shuah Khan <skhan@linuxfoundation.org>
Cc: Valentina Manea <valentina.manea.m@gmail.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: linux-usb@vger.kernel.org
Link: https://lore.kernel.org/r/20201019101110.332963099@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The usage of in_interrupt() in drivers is phased out for various reasons.
Documenting calling contexts of functions with 'in_interrupt()' or
'!in_interrupt()' is imprecise: For a function which might sleep the
condition is preemptible task context, which is not what '!in_interrupt()'
describes.
Replace the context docummentation with plain text and make them match
reality.
Signed-off-by: Ahmed S. Darwish <a.darwish@linutronix.de>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Felipe Balbi <balbi@kernel.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-usb@vger.kernel.org
Link: https://lore.kernel.org/r/20201019101110.636378243@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
