Just as we recently added support for other stored firmware flash
versions, support display of the stored UNDI Option ROM version via
devlink info.
To do this, we need to introduce a new ice_get_inactive_orom_ver
function. This is a little trickier than with other flash versions. The
Option ROM version data was being read from a special "Boot
Configuration" block of the NVM Preserved Field Area. This block only
contains the *active* Option ROM version data. It is populated when the
device firmware finishes updating the Option ROM.
This method is ineffective at reading the stored Option ROM version
data. Instead of reading from this section of the flash, replace this
version extraction with one which locates the Combo Version information
from within the Option ROM binary.
This data is stored within the Option ROM at a 512 byte offset, in
a simple structured format. The structure uses a simple modulo 256
checksum for integrity verification. Scan through the Option ROM to
locate the CIVD data section, and extract the Combo Version.
Refactor ice_get_orom_ver_info so that it takes the bank select
enumeration parameter. Use this to implement ice_get_inactive_orom_ver.
Although all ice devices have a Boot Configuration block in the NVM PFA,
not all devices have a valid Option ROM. In this case, the old
ice_get_orom_ver_info would "succeed" but report a version of all
zeros. The new implementation would fail to locate the $CIV section in
the Option ROM and report an error. Thus, we must ensure that
ice_init_nvm does not fail if ice_get_orom_ver_info fails.
Use the new ice_get_inactive_orom_ver to allow reporting the Option ROM
versions for a pending update via devlink info.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Add a function to read the inactive netlist bank for version
information. To support this, refactor how we read the netlist version
data. Instead of using the firmware AQ interface with a module ID, read
from the flash as a flat NVM, using ice_read_flash_module.
This change requires a slight adjustment to the offset values used, as
reading from the flat NVM includes the type field (which was stripped by
firmware previously). Cleanup the macro names and move them to
ice_type.h. For clarity in how we calculate the offsets and so that
programmers can easily map the offset value to the data sheet, use
a wrapper macro to account for the offset adjustments.
Use the newly added ice_get_inactive_netlist_ver function to extract the
version data from the pending netlist module update. Add the stored
variants of "fw.netlist", and "fw.netlist.build" to the info version map
array.
With this change, we now report the "fw.netlist" and "fw.netlist.build"
versions into the stored section of the devlink info report. As with the
main NVM module versions, if there is no pending update, we report the
currently active values as stored.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The devlink info interface supports drivers reporting "stored" versions.
These versions indicate the version of an update that has been
downloaded to the device, but is not yet active.
The code for extracting the NVM version recently changed to enable
support for reading from either the active or the inactive bank. Use
this to implement ice_get_inactive_nvm_ver, which will read the NVM
version data from the inactive section of flash.
When reporting the versions via devlink info, first read the device
capabilities. Determine if there is a pending flash update, and if so,
extract relevant version information from the inactive flash. Store
these within the info context structure.
When reporting "stored" firmware versions, devlink documentation
indicates that we ought to always report a stored value, even if there
is no pending update. In this common case, the stored version should
match the running version. This means that each stored version should by
default fallback to the same value as reported by the running handler.
To support this, modify the version structure to have both a "getter"
and a "fallback". Modify the control loop so that it will use the
"fallback" function if the "getter" function does not report a version.
To report versions for which we can read the stored value, use a new
"stored()" macro. This macro will insert two entries into the version
list. The first entry is the traditional running version. The second is
the stored version, implemented with a fallback to the active version.
This is a little tricky, but reduces the overall duplication of elements
in the entry list, and ensures that running and stored values remain
consistent.
To avoid some duplication, add a combined() macro that will insert both
the running and stored versions into the version entry list.
Using this new support, add pending version reporter functions for
"fw.psid.api" and "fw.bundle_id". This enables reporting the stored
values for some of versions in the NVM module of the flash.
Reporting management versions is not implemented by this patch. The
active management version is reported to the driver via the AdminQ
mailbox during load. Although the version must be in the firmware binary
somewhere, accessing this from the inactive firmware is not trivial and
has not been implemented in this change.
Future changes will introduce support for reading the UNDI Option ROM
version and the version associated with the Netlist module.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
When reading from the flash memory of the device, the ice driver has two
interfaces available to it. First, it can use a mediated interface via
firmware that allows specifying a module ID. This allows reading from
specific modules of the active flash bank.
The second interface available is to perform flat reads. This allows
complete access to the entire flash. However, using it requires the
software to handle calculating module location and interpret pointer
addresses.
While most data required is accessible through the convenient first
interface, certain flash contents are not. This includes the CSS header
information associated with the Option ROM and NVM banks, as well as any
access to the "inactive" banks used as scratch space for performing
flash updates.
In order to access all of the relevant flash contents, software must use
the flat reads. Rather than forcing all flows to perform flat read
calculations, introduce a new abstraction for reading from the flash:
ice_read_flash_module. This function provides an abstraction for reading
from either the active or inactive flash bank at the requested module.
This interface is very similar to the abstraction provided via firmware,
but allows access to additional modules, as well as providing
a mechanism to request access to both flash banks.
At first glance, it might make sense for this abstraction to allow
specifying precisely which bank (1st or 2nd) the caller wishes to read.
This is simpler to implement but more difficult to use. In practice,
most callers only know whether they want the active bank, or the
inactive bank. Rather than force callers to determine for themselves
which bank to read from, implement ice_read_flash_module in terms of
"active" vs "inactive". This significantly simplifies the implementation
at the caller level and is a more useful abstraction over the flash
contents.
Make use of this new interface to refactor reading of the main NVM
version information. Instead of using the firmware's mediated ShadowRAM
function, use the ice_read_flash_module abstraction.
To do this, notice that most reads of the NVM are going to be in 2-byte
word chunks. To simplify using ice_read_flash_module for this case,
ice_read_nvm_module is introduced. This is a simple wrapper around
ice_read_flash_module which takes the correct pointer address for the
NVM bank, and forces the 2-byte word format onto the caller.
When reading the NVM versions, some fields are read from the Shadow RAM.
The Shadow RAM is the first 64KB of flash memory, and is populated
during device load. Most fields are copied from a section within the
active NVM bank. In order to read this data from both the active and
inactive NVM banks, we need to read not from the first 64KB of flash,
but instead from the correct offset into the NVM bank. Introduce
ice_read_nvm_sr_copy for this purpose. This function wraps around
ice_read_nvm_module and has the same interface as the ice_read_sr_word,
with the exception of allowing the caller to specify whether to read the
active or inactive flash bank.
With this change, it is now trivial to refactor ice_get_nvm_ver_info to
read using the software mediated ice_read_flash_module interface instead
of relying on the firmware mediated interface. This will be used in the
following change to implement support for stored versions in the devlink
info report.
Additionally, the overall ice_read_flash_module interface will be used
and extended to support all three major flash banks, and additionally to
support reading the flash image security revision information.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The ice flash contains two copies of each of the NVM, Option ROM, and
Netlist modules. Each bank has a pointer word and a size word. In order
to correctly read from the active flash bank, the driver must calculate
the offset manually.
During NVM initialization, read the Shadow RAM control word and
determine which bank is active for each NVM module. Additionally, cache
the size and pointer values for use in calculating the correct offset.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The ice driver uses an array of structures which link an info name with
a function that formats the associated version data into a string.
All existing format functions simply format already captured static data
from the driver hw structure. Future changes will introduce format
functions for reporting the versions of flash sections stored but not
yet applied. This type of version data is not stored as a member of the
hw structure. This is because (a) it might not yet exist in the case
there is no pending flash update, and (b) even if it does, it might
change such as if an update is canceled or replaced by a new update
before finalizing.
We could simply have each format function gather its own data upon being
called. However, in some cases the raw binary version data is
a combination of multiple different reported fields. Additionally, the
current interface doesn't have a way for the function to indicate that
the version doesn't exist.
Refactor this function interface to take a new ice_info_ctx structure
instead of the buffer pointer and length. This context structure allows
for future extensions to pre-gather version data that is stored within
the context struct instead of the hw struct.
Allocate this context structure initially at the start of
ice_devlink_info_get. We use dynamic allocation instead of a local stack
variable in order to avoid using too much kernel stack once we extend it
with additional data structures.
Modify the main loop that drives the info reporting so that the version
buffer string is always cleared between each format. Explicitly check
that the format function actually filled in a version string of non-zero
length. If the string is not provided, simply skip this version without
reporting an error. This allows for introducing format functions of
versions which may or may not be present, such as the version of
a pending update that has not yet been activated.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The ice_nvm_info structure has become somewhat of a dumping ground for
all of the fields related to flash version. It holds the NVM version and
EETRACK id, the OptionROM info structure, the flash size, the ShadowRAM
size, and more.
A future change is going to add the ability to read the NVM version and
EETRACK ID from the inactive NVM bank. To make this simpler, it is
useful to have these NVM version info fields extracted to their own
structure.
Rename ice_nvm_info into ice_flash_info, and create a separate
ice_nvm_info structure that will contain the eetrack and NVM map
version. Move the netlist_ver structure into ice_flash_info and rename it
ice_netlist_info for consistency.
Modify the static ice_get_orom_ver_info to take the option rom structure
as a pointer. This makes it more obvious what portion of the hw struct
is being modified. Do the same for ice_get_netlist_ver_info.
Introduce a new ice_get_nvm_ver_info function, which will be similar to
ice_get_orom_ver_info and ice_get_netlist_ver_info, used to keep the NVM
version extraction code co-located.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
When erasing, notify userspace of how long we will potentially take to
erase a module. Doing so allows userspace to report the timeout, giving
a clear indication of the upper time bound of the operation.
Since we're re-using the erase timeout value, make it a macro rather
than a magic number.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Shannon Nelson <snelson@pensando.io>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tony Nguyen says:
====================
1GbE Intel Wired LAN Driver Updates 2021-02-03
This series contains updates to igc, igb, e1000e, and e1000 drivers.
Sasha adds counting of good transmit packets and reporting of NVM version
and gPHY version in ethtool firmware version. Replaces the use of strlcpy
to the preferred strscpy. Fixes a typo that caused the wrong register to be
output. He also removes an unused function pointer, some unneeded defines,
and a non-applicable comment. All changes for igc.
Gal Hammer fixes a typo which caused the RDBAL register values to be
shown instead of TDBAL for igb.
Nick Lowe enables RSS support for i211 devices for igb.
Tom Rix fixes checkpatch warning by removing h from printk format
specifier for igb.
Kaixu Xia removes setting of a variable that is overwritten before next
use for e1000e.
Sudip Mukherjee removes an unneeded assignment for e1000.
* '1GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/next-queue:
e1000: drop unneeded assignment in e1000_set_itr()
e1000e: remove the redundant value assignment in e1000_update_nvm_checksum_spt
igb: remove h from printk format specifier
igb: Enable RSS for Intel I211 Ethernet Controller
igb: fix TDBAL register show incorrect value
igc: Fix TDBAL register show incorrect value
igc: Remove unused FUNC_1 mask
igc: Remove unused local receiver mask
igc: Prefer strscpy over strlcpy
igc: Expose the gPHY firmware version
igc: Expose the NVM version
igc: Add Host Good Packets Transmitted Count
igc: Remove MULR mask define
igc: Remove igc_set_fw_version comment
igc: Clean up nvm_operations structure
====================
Link: https://lore.kernel.org/r/20210204004259.3662059-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Now we can remove a bunch of identical functions from the drivers and
make them use common dev_page_is_reusable(). All {,un}likely() checks
are omitted since it's already present in this helper.
Also update some comments near the call sites.
Suggested-by: David Rientjes <rientjes@google.com>
Suggested-by: Jakub Kicinski <kuba@kernel.org>
Cc: John Hubbard <jhubbard@nvidia.com>
Signed-off-by: Alexander Lobakin <alobakin@pm.me>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The variable 'current_itr' is assigned to 0 before jumping to
'set_itr_now' but it has not been used after the jump. So, remove the
unneeded assignment.
Signed-off-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Reviewed-by: Lukas Bulwahn <lukas.bulwahn@gmail.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Both of the statements are value assignment of the variable act_offset.
The first value assignment is overwritten by the second and is useless.
Remove it.
Reported-by: Tosk Robot <tencent_os_robot@tencent.com>
Signed-off-by: Kaixu Xia <kaixuxia@tencent.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
This change fixes the checkpatch warning described in this
commit cbacb5ab0a ("docs: printk-formats: Stop encouraging use of
unnecessary %h[xudi] and %hh[xudi]")
Standard integer promotion is already done and %hx and %hhx is useless
so do not encourage the use of %hh[xudi] or %h[xudi].
Signed-off-by: Tom Rix <trix@redhat.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The Intel I211 Ethernet Controller supports 2 Receive Side Scaling (RSS)
queues. It should not be excluded from having this feature enabled.
Via commit c883de9fd7 ("igb: rename igb define to be more generic")
E1000_MRQC_ENABLE_RSS_4Q was renamed to E1000_MRQC_ENABLE_RSS_MQ to
indicate that this is a generic bit flag to enable queues and not
a flag that is specific to devices that support 4 queues
The bit flag enables 2, 4 or 8 queues appropriately depending on the part.
Tested with a multicore CPU and frames were then distributed as expected.
This issue appears to have been introduced because of confusion caused
by the prior name.
Signed-off-by: Nick Lowe <nick.lowe@gmail.com>
Tested-by: David Switzer <david.switzer@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Fixed a typo which caused the registers dump function to read the
RDBAL register when printing TDBAL register values.
Signed-off-by: Gal Hammer <ghammer@redhat.com>
Tested-by: David Switzer <david.switzer@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Fixed a typo which caused the registers dump function to read the
RDBAL register when printing TDBAL register values.
_reg_dump method has been partially derived from i210 and have
same typo.
Suggested-by: Gal Hammer <ghammer@redhat.com>
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Local receiver mask SR_1000T_LOCAL_RX_STATUS not in use in i225 device
and could be removed
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Use the strscpy method instead of strlcpy method.
See: https://lore.kernel.org/r/CAHk-=wgfRnXz0W3D37d01q3JFkr
_i_uTL=V6A6G1oUZcprmknw@mail.gmail.com/
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Extend reporting of NVM image version to include the gPHY (i225 PHY)
firmware version.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Expose the NVM map version via drvinfo in ethtool
NVM image version is reported as firmware version for i225 device
Minor typo fix - remove space
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
This counter counts the number of good (non-erred) packets
transmitted sent by the host.
A good transmit packet is considered one that is 64 or more bytes
in length (from <Destination Address> through <CRC>,
inclusively) in length
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Multiple Tx Data Read Requests is hardware pipeline feature and
is not controlled by software
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
i225 device not supported and do not plan to support
configuration of fw version string for ethtool
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
valid_led_default function pointer not in use and can
be removed from nvm_operations structure.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
This reverts commit 2ad1274fa3
VF queues were not brought up when PF was brought up after being
downed if the VF driver disabled VFs queues during PF down.
This could happen in some older or external VF driver implementations.
The problem was that PF driver used vf->queues_enabled as a condition
to decide what link-state it would send out which caused the issue.
Remove the check for vf->queues_enabled in the VF link notify.
Now VF will always be notified of the current link status.
Also remove the queues_enabled member from i40e_vf structure as it is
not used anymore. Otherwise VNF implementation was broken and caused
a link flap.
The original commit was a workaround to avoid breaking existing VFs though
it's really a fault of the VF code not the PF. The commit should be safe to
revert as all of the VFs we know of have been fixed. Also, since we now
know there is a related bug in the workaround, removing it is preferred.
Fixes: 2ad1274fa3 ("i40e: don't report link up for a VF who hasn't enabled")
Signed-off-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Signed-off-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
This patch sets the default return value to -IGC_ERR_NVM in
igc_write_nvm_srwr. Without this change it wouldn't lead to a shadow RAM
write EEWR timeout.
Fixes: ab40561268 ("igc: Add NVM support")
Signed-off-by: Kevin Lo <kevlo@kevlo.org>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
drivers/net/can/dev.c
b552766c87 ("can: dev: prevent potential information leak in can_fill_info()")
3e77f70e73 ("can: dev: move driver related infrastructure into separate subdir")
0a042c6ec9 ("can: dev: move netlink related code into seperate file")
Code move.
drivers/net/ethernet/mellanox/mlx5/core/en_ethtool.c
57ac4a31c4 ("net/mlx5e: Correctly handle changing the number of queues when the interface is down")
214baf2287 ("net/mlx5e: Support HTB offload")
Adjacent code changes
net/switchdev/switchdev.c
20776b465c ("net: switchdev: don't set port_obj_info->handled true when -EOPNOTSUPP")
ffb68fc58e ("net: switchdev: remove the transaction structure from port object notifiers")
bae33f2b5a ("net: switchdev: remove the transaction structure from port attributes")
Transaction parameter gets dropped otherwise keep the fix.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Link speed advertising in igc has two problems:
- When setting the advertisement via ethtool, the link speed is converted
to the legacy 32 bit representation for the intel PHY code.
This inadvertently drops ETHTOOL_LINK_MODE_2500baseT_Full_BIT (being
beyond bit 31). As a result, any call to `ethtool -s ...' drops the
2500Mbit/s link speed from the PHY settings. Only reloading the driver
alleviates that problem.
Fix this by converting the ETHTOOL_LINK_MODE_2500baseT_Full_BIT to the
Intel PHY ADVERTISE_2500_FULL bit explicitly.
- Rather than checking the actual PHY setting, the .get_link_ksettings
function always fills link_modes.advertising with all link speeds
the device is capable of.
Fix this by checking the PHY autoneg_advertised settings and report
only the actually advertised speeds up to ethtool.
Fixes: 8c5ad0dae9 ("igc: Add ethtool support")
Signed-off-by: Corinna Vinschen <vinschen@redhat.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
This change simplifies the VF initialization check and also minimizes
the delay between acquiring the VSI pointer and using it. As known by
the commit being fixed, there is a risk of the VSI pointer getting
changed. Therefore minimize the delay between getting and using the
pointer.
Fixes: 9889707b06 ("i40e: Fix crash caused by stress setting of VF MAC addresses")
Signed-off-by: Stefan Assmann <sassmann@kpanic.de>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The current MSI-X enablement logic tries to enable best-case MSI-X
vectors and if that fails we only support a bare-minimum set. This
includes a single MSI-X for 1 Tx and 1 Rx queue and a single MSI-X
for the OICR interrupt. Unfortunately, the driver fails to load when we
don't get as many MSI-X as requested for a couple reasons.
First, the code to allocate MSI-X in the driver tries to allocate
num_online_cpus() MSI-X for LAN traffic without caring about the number
of MSI-X actually enabled/requested from the kernel for LAN traffic.
So, when calling ice_get_res() for the PF VSI, it returns failure
because the number of available vectors is less than requested. Fix
this by not allowing the PF VSI to allocation more than
pf->num_lan_msix MSI-X vectors and pf->num_lan_msix Rx/Tx queues.
Limiting the number of queues is done because we don't want more than
1 Tx/Rx queue per interrupt due to performance conerns.
Second, the driver assigns pf->num_lan_msix = 2, to account for LAN
traffic and the OICR. However, pf->num_lan_msix is only meant for LAN
MSI-X. This is causing a failure when the PF VSI tries to
allocate/reserve the minimum pf->num_lan_msix because the OICR MSI-X has
already been reserved, so there may not be enough MSI-X vectors left.
Fix this by setting pf->num_lan_msix = 1 for the failure case. Then the
ICE_MIN_MSIX accounts for the LAN MSI-X and the OICR MSI-X needed for
the failure case.
Update the related defines used in ice_ena_msix_range() to align with
the above behavior and remove the unused RDMA defines because RDMA is
currently not supported. Also, remove the now incorrect comment.
Fixes: 152b978a1f ("ice: Rework ice_ena_msix_range")
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Currently users could create more channels than LAN MSI-X available.
This is happening because there is no check against pf->num_lan_msix
when checking the max allowed channels and will cause performance issues
if multiple Tx and Rx queues are tied to a single MSI-X. Fix this by not
allowing more channels than LAN MSI-X available in pf->num_lan_msix.
Fixes: 87324e747f ("ice: Implement ethtool ops for channels")
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Fix the driver to copy the MAC address configured in ndo_set_mac_address
into dev_addr, even if the MAC filter already exists in HW. In some
situations (e.g. bonding) the netdev's dev_addr could have been modified
outside of the driver, with no change to the HW filter, so the driver
cannot assume that they match.
Fixes: 757976ab16 ("ice: Fix check for removing/adding mac filters")
Signed-off-by: Nick Nunley <nicholas.d.nunley@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
This patch is based on a similar change to i40e by Slawomir Laba:
"i40e: Implement flow for IPv6 next header (extension header)".
When a packet contains an IPv6 header with next header which is
an extension header and not a protocol one, the kernel function
skb_transport_header called with such sk_buff will return a
pointer to the extension header and not to the TCP one.
The above explained call caused a problem with packet processing
for skb with encapsulation for tunnel with ICE_TX_CTX_EIPT_IPV6.
The extension header was not skipped at all.
The ipv6_skip_exthdr function does check if next header of the IPV6
header is an extension header and doesn't modify the l4_proto pointer
if it points to a protocol header value so its safe to omit the
comparison of exthdr and l4.hdr pointers. The ipv6_skip_exthdr can
return value -1. This means that the skipping process failed
and there is something wrong with the packet so it will be dropped.
Fixes: a4e82a81f5 ("ice: Add support for tunnel offloads")
Signed-off-by: Nick Nunley <nicholas.d.nunley@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The packet classifier would occasionally misrecognize an IPv6 training
packet when the next protocol field was 0. The correct value for
unspecified protocol is IPPROTO_NONE.
Fixes: 165d80d6ad ("ice: Support IPv6 Flow Director filters")
Signed-off-by: Henry Tieman <henry.w.tieman@intel.com>
Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Using skb_csum_is_sctp is a easier way to validate it's a SCTP CRC
checksum offload packet, and yet it also makes ixgbevf support SCTP
CRC checksum offload for UDP and GRE encapped packets, just as it
does in igb driver.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Reviewed-by: Alexander Duyck <alexanderduyck@fb.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Using skb_csum_is_sctp is a easier way to validate it's a SCTP CRC
checksum offload packet, and yet it also makes ixgbe support SCTP
CRC checksum offload for UDP and GRE encapped packets, just as it
does in igb driver.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Reviewed-by: Alexander Duyck <alexanderduyck@fb.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Using skb_csum_is_sctp is a easier way to validate it's a SCTP CRC
checksum offload packet, and yet it also makes igc support SCTP
CRC checksum offload for UDP and GRE encapped packets, just as it
does in igb driver.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Reviewed-by: Alexander Duyck <alexanderduyck@fb.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Using skb_csum_is_sctp is a easier way to validate it's a SCTP CRC
checksum offload packet, and yet it also makes igbvf support SCTP
CRC checksum offload for UDP and GRE encapped packets, just as it
does in igb driver.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Reviewed-by: Alexander Duyck <alexanderduyck@fb.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Using skb_csum_is_sctp is a easier way to validate it's a SCTP
CRC checksum offload packet, and there is no need to parse the
packet to check its proto field, especially when it's a UDP or
GRE encapped packet.
So this patch also makes igb support SCTP CRC checksum offload
for UDP and GRE encapped packets.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Reviewed-by: Alexander Duyck <alexanderduyck@fb.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Daniel Borkmann says:
====================
pull-request: bpf-next 2021-01-16
1) Extend atomic operations to the BPF instruction set along with x86-64 JIT support,
that is, atomic{,64}_{xchg,cmpxchg,fetch_{add,and,or,xor}}, from Brendan Jackman.
2) Add support for using kernel module global variables (__ksym externs in BPF
programs) retrieved via module's BTF, from Andrii Nakryiko.
3) Generalize BPF stackmap's buildid retrieval and add support to have buildid
stored in mmap2 event for perf, from Jiri Olsa.
4) Various fixes for cross-building BPF sefltests out-of-tree which then will
unblock wider automated testing on ARM hardware, from Jean-Philippe Brucker.
5) Allow to retrieve SOL_SOCKET opts from sock_addr progs, from Daniel Borkmann.
6) Clean up driver's XDP buffer init and split into two helpers to init per-
descriptor and non-changing fields during processing, from Lorenzo Bianconi.
7) Minor misc improvements to libbpf & bpftool, from Ian Rogers.
* https://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf-next: (41 commits)
perf: Add build id data in mmap2 event
bpf: Add size arg to build_id_parse function
bpf: Move stack_map_get_build_id into lib
bpf: Document new atomic instructions
bpf: Add tests for new BPF atomic operations
bpf: Add bitwise atomic instructions
bpf: Pull out a macro for interpreting atomic ALU operations
bpf: Add instructions for atomic_[cmp]xchg
bpf: Add BPF_FETCH field / create atomic_fetch_add instruction
bpf: Move BPF_STX reserved field check into BPF_STX verifier code
bpf: Rename BPF_XADD and prepare to encode other atomics in .imm
bpf: x86: Factor out a lookup table for some ALU opcodes
bpf: x86: Factor out emission of REX byte
bpf: x86: Factor out emission of ModR/M for *(reg + off)
tools/bpftool: Add -Wall when building BPF programs
bpf, libbpf: Avoid unused function warning on bpf_tail_call_static
selftests/bpf: Install btf_dump test cases
selftests/bpf: Fix installation of urandom_read
selftests/bpf: Move generated test files to $(TEST_GEN_FILES)
selftests/bpf: Fix out-of-tree build
...
====================
Link: https://lore.kernel.org/r/20210116012922.17823-1-daniel@iogearbox.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Currently, the function i40e_construct_skb_zc only frees the input xdp
buffer when the output skb is successfully built. On error, the
function i40e_clean_rx_irq_zc does not commit anything for the current
packet descriptor and simply exits the packet descriptor processing
loop, with the plan to restart the processing of this descriptor on
the next invocation. Therefore, on error the ring next-to-clean
pointer should not advance, the xdp i.e. *bi buffer should not be
freed and the current buffer info should not be invalidated by setting
*bi to NULL. Therefore, the *bi should only be set to NULL when the
function i40e_construct_skb_zc is successful, otherwise a NULL *bi
will be dereferenced when the work for the current descriptor is
eventually restarted.
Fixes: 3b4f0b66c2 ("i40e, xsk: Migrate to new MEM_TYPE_XSK_BUFF_POOL")
Signed-off-by: Cristian Dumitrescu <cristian.dumitrescu@intel.com>
Acked-by: Björn Töpel <bjorn.topel@intel.com>
Link: https://lore.kernel.org/r/20210111181138.49757-1-cristian.dumitrescu@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
napi_gro_receive() can never return GRO_DROP
GRO_DROP can only be returned from napi_gro_frags()
which is the other NAPI GRO entry point.
Followup patch will remove GRO_DROP, because drivers
are not supposed to call napi_gro_frags() if prior
napi_get_frags() has failed.
Note that I have left the gro_dropped variable. I leave to ice
maintainers the decision to further remove it from ethtool -S results.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
