Add support for CHV gpio programming in DSI gpio elements.
v2: Overhaul macros according to Ville's review.
v3: Address Ville's review:
- swap E and SE gpio ranges
- add a note about max SE index
- use GPO, not HIZ
- swap cfg0 and cfg1
v4: fix port for dsi sequence versions 1 and 2
[Rewritten by Jani, based on earlier work by Yogesh and Deepak.]
Signed-off-by: Yogesh Mohan Marimuthu <yogesh.mohan.marimuthu@intel.com>
Signed-off-by: Deepak M <m.deepak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/bdaaf9915a5005305b31bb26cf619a5a82472f2a.1461666263.git.jani.nikula@intel.com
For dual link panel scenarios there are new fields added in the
VBT which indicate on which port the PWM cntrl and CABC ON/OFF
commands needs to be sent.
v2: Moving the comment to intel_dsi.h(Jani)
v3: Renaming the field names (Jani)
v4 by Jani: make this patch only about VBT
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Daniel Vetter <daniel.vetter@intel.com>
Cc: Yetunde Adebisi <yetundex.adebisi@intel.com>
Signed-off-by: Deepak M <m.deepak@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1459346623-30752-2-git-send-email-jani.nikula@intel.com
This patch adds support for eDP backlight control using DPCD registers to
backlight hooks in intel_panel.
It checks for backlight control over AUX channel capability and sets up
function pointers to get and set the backlight brightness level if
supported.
v2: Moved backlight functions from intel_dp.c into a new file
intel_dp_aux_backlight.c. Also moved reading of eDP display control
registers to intel_dp_get_dpcd
v3: Correct some formatting mistakes
v4: Updated to use AUX backlight control if PWM control is not possible
(Jani)
v5: Moved call to initialize backlight registers to dp_aux_setup_backlight
v6: Check DP_EDP_BACKLIGHT_PIN_ENABLE_CAP is disabled before setting up AUX
backlight control. To fix BLM_PWM_ENABLE igt test warnings on bdw_ultra
v7: Add enable_dpcd_backlight module parameter.
v8: Rebase onto latest drm-intel-nightly branch
v9: Remove changes to intel_dp_dpcd_read_wake
Split addition edp_dpcd variable into a separate patch
Cc: Bob Paauwe <bob.j.paauwe@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Yetunde Adebisi <yetundex.adebisi@intel.com>
[Jani: whitepace changes to appease checkpatch]
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1459865452-9138-4-git-send-email-yetundex.adebisi@intel.com
Can use the new vma->is_ggtt to simplify the check and
remove the local variables.
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Dave Gordon <david.s.gordon@intel.com>
Can use vma->is_ggtt to simplify the check and also switch the
BUG_ON to GEM_BUG_ON which is more appropriate for this.
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Dave Gordon <david.s.gordon@intel.com>
Only caller is i915_gem_obj_ggtt_size which only cares about
GGTT so simplify it and implement under that name.
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Because having both i915_gem_object_alloc() and i915_gem_alloc_object()
(with different return conventions) is just too confusing!
(i915_gem_object_alloc() is the low-level memory allocator, and remains
unchanged, whereas i915_gem_alloc_object() is a constructor that ALSO
initialises the newly-allocated object.)
Signed-off-by: Dave Gordon <david.s.gordon@intel.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1461348872-4702-1-git-send-email-david.s.gordon@intel.com
Move the better constructs/comments from i915_gem_stolen.c to
early-quirks.c and increase readability in preparation of only
having one set of functions.
- intel_stolen_base -> gen3_stolen_base
- use phys_addr_t instead of u32 for address for future proofing
v2:
- Print the invalid register values (Chris)
(Omitting the register prefix as it's visible from backtrace.)
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Acked-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
This patch applies a performance enhancement workaround
based on analysis of DX and OCL S-Curve workloads. We
increase the General Priority Credits for L3SQ from the
hardware default of 56 to the max value 62, and decrease
the High Priority credits from 8 to 2.
v2: Only apply to B0 onwards
v3: Move w/a to per engine init, ie bxt_init_workarounds
Signed-off-by: Tim Gore <tim.gore@intel.com>
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1461314761-36854-1-git-send-email-tim.gore@intel.com
Reviewed-by: Michel Thierry <michel.thierry@intel.com>
As a part of WaGsvDisableTurbo, Driver makes an early exit from the
Gen9 Turbo enabling function, so doesn't program the Turbo Control register.
But BIOS could leave the Hw Turbo as enabled, so need to explicitly clear
out the Control register just to avoid inconsitency with debugfs
interface, which will show Turbo as enabled only and that is not expected
after adding the WaGsvDisableTurbo. Apart from this there is no problem
even if the Turbo is left enabled in the Control register, as the Up/Down
interrupts would remain masked.
v2: Add explicit clearing of Turbo Control register to *_disable_rps()
also for the similar consistency (Chris)
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Akash Goel <akash.goel@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/1461350146-23454-2-git-send-email-akash.goel@intel.com
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
There are certain registers, which captures the time elapsed in the
in current Up/Down EI, for how long GT has been Idle/Busy/Avg in the
current Up/Down EI and also in the previous Up/Down EI.
These register values are reported by the i915_frequency_info debugfs
interface. The Driver prints the 'us' suffix after the values, albeit
they are actually in raw form & not in microsecond units.
This patch removes the 'us' suffix so that its clear to User that values
are indeed in raw form.
v2: Present the values in microseconds unit also, after platform
specific conversion (Chris)
v3: Add a space between raw & microsecond value (Chris)
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Akash Goel <akash.goel@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/1461350146-23454-3-git-send-email-akash.goel@intel.com
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Added a new GT_PM_INTERVAL_TO_US macro to perform the platform
specific conversion of PM time interval values to microseconds unit.
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Akash Goel <akash.goel@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/1461350146-23454-1-git-send-email-akash.goel@intel.com
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Somehow my SNB GT1 (Dell XPS 8300) gets very unhappy around
GPU hangs if the RPS EI/thresholds aren't suitably aligned.
It seems like scheduling/timer interupts stop working somehow
and things get stuck eg. in usleep_range().
I bisected the problem down to
commit 8a5864377b ("drm/i915/skl: Restructured the gen6_set_rps_thresholds function")
I observed that before all the values were at least multiples of 25,
but afterwards they are not. And rounding things up to the next multiple
of 25 does seem to help, so lets' do that. I also tried roundup(..., 5)
but that wasn't sufficient. Also I have no idea if we might need this sort of
thing on gen9+ as well.
These are the original EI/thresholds:
LOW_POWER
GEN6_RP_UP_EI 12500
GEN6_RP_UP_THRESHOLD 11800
GEN6_RP_DOWN_EI 25000
GEN6_RP_DOWN_THRESHOLD 21250
BETWEEN
GEN6_RP_UP_EI 10250
GEN6_RP_UP_THRESHOLD 9225
GEN6_RP_DOWN_EI 25000
GEN6_RP_DOWN_THRESHOLD 18750
HIGH_POWER
GEN6_RP_UP_EI 8000
GEN6_RP_UP_THRESHOLD 6800
GEN6_RP_DOWN_EI 25000
GEN6_RP_DOWN_THRESHOLD 15000
These are after 8a5864377b:
LOW_POWER
GEN6_RP_UP_EI 12500
GEN6_RP_UP_THRESHOLD 11875
GEN6_RP_DOWN_EI 25000
GEN6_RP_DOWN_THRESHOLD 21250
BETWEEN
GEN6_RP_UP_EI 10156
GEN6_RP_UP_THRESHOLD 9140
GEN6_RP_DOWN_EI 25000
GEN6_RP_DOWN_THRESHOLD 18750
HIGH_POWER
GEN6_RP_UP_EI 7812
GEN6_RP_UP_THRESHOLD 6640
GEN6_RP_DOWN_EI 25000
GEN6_RP_DOWN_THRESHOLD 15000
And these are what we have after this patch:
LOW_POWER
GEN6_RP_UP_EI 12500
GEN6_RP_UP_THRESHOLD 11875
GEN6_RP_DOWN_EI 25000
GEN6_RP_DOWN_THRESHOLD 21250
BETWEEN
GEN6_RP_UP_EI 10175
GEN6_RP_UP_THRESHOLD 9150
GEN6_RP_DOWN_EI 25000
GEN6_RP_DOWN_THRESHOLD 18750
HIGH_POWER
GEN6_RP_UP_EI 7825
GEN6_RP_UP_THRESHOLD 6650
GEN6_RP_DOWN_EI 25000
GEN6_RP_DOWN_THRESHOLD 15000
Cc: stable@vger.kernel.org
Cc: Akash Goel <akash.goel@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Testcase: igt/kms_pipe_crc_basic/hang-read-crc-pipe-B
Fixes: 8a5864377b ("drm/i915/skl: Restructured the gen6_set_rps_thresholds function")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1461159836-9108-1-git-send-email-ville.syrjala@linux.intel.com
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>
This patch does the following:
- Fakes live status of HDMI as connected (even if that's not).
While testing certain (monitor + cable) combinations with
various intel platforms, it seems that live status register
doesn't work reliably on some older devices. So limit the
live_status check for HDMI detection, only for platforms
from gen7 onwards.
V2: restrict faking live_status to certain platforms
V3: (Ville)
- keep the debug message for !live_status case
- fix indentation of comment
- remove "warning" from the debug message
(Jani)
- Change format of fix details in the commit message
Fixes: 237ed86c69 ("drm/i915: Check live status before reading edid")
Cc: stable@vger.kernel.org # v4.4
Suggested-by: Ville Syrjala <ville.syrjala@linux.intel.com>
Signed-off-by: Shashank Sharma <shashank.sharma@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1461237606-16491-1-git-send-email-shashank.sharma@intel.com
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
It's possible that BIOS enables PHY0, but it programmes only the first
channel on it. Since we program the PHYs only during driver loading this
is an incorrect configuration from the driver's point of view, since we
may use both channels eventually. Detect this scenario and force
reprogramming the PHY in this case.
The actual scenario for me was that the lane optimization for the second
channel in PHY0 was not setup by BIOS and so a state verification
warning was triggered. Everything else was setup properly.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1461174366-16758-4-git-send-email-imre.deak@intel.com
If we skipped PHY0 initialization because it was already enabled by
BIOS, we still have to wait for the PHY1 GRC calibration as that is
done as part of the PHY0 init.
v2:
- Use the actual PHY index in the debug message in
broxton_phy_wait_grc_done() (Ville)
CC: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1461255561-1644-1-git-send-email-imre.deak@intel.com
It's possible that BIOS enables PHY1 only to read out the GRC value from
it to be used in PHY0 and then disables PHY1. In this case we can't use
the PHY1 GRC value for state verification, so use instead the one in PHY0
always.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1461174366-16758-2-git-send-email-imre.deak@intel.com
Remove dev local and use to_i915() in gen8_ppgtt_notify_vgt.
v2: use dev_priv directly for QUESTION_MACROS (Joonas Lahtinen)
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Signed-off-by: Matthew Auld <matthew.auld@intel.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1461323365-21256-1-git-send-email-matthew.auld@intel.com
Right after runtime resume we know that we can re-enable DC5, since we
just disabled DC9 and power well 2 is disabled. So enable DC5 explicitly
instead of delaying this until the next time we disable power well 2.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Bob Paauwe <bob.j.paauwe@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1461173277-16090-5-git-send-email-imre.deak@intel.com
After suspend-to-ram or -disk we don't know what power state the display
HW will be, DC0 or DC9 are both possible states, so reset the software
DC state tracking in these cases. This gets rid of 'DC state mismatch'
error messages during resuming from ram or disk where we expected to be
in DC9 (as set by the suspend handler) but we are in DC0.
v2:
- Remove extra WS in gen9_sanitize_dc_state() (Bob)
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Bob Paauwe <bob.j.paauwe@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1461173277-16090-4-git-send-email-imre.deak@intel.com
Initially we thought that the platform specific suspend/resume sequences
can be shared between the runtime and system suspend/resume handlers.
This turned out to be not true, we have quite a few differences on most
of the platforms. This was realized already earlier by Paulo who
inlined the platform specific resume_prepare handlers. We have the
same problem with the corresponding suspend_complete handlers, there are
platform differences that make it unfeasible to share the code between
the runtime and system suspend paths. Also now we call functions that
need to be paired like hsw_enable_pc8()/hsw_disable_pc8() from different
levels of the call stack, which is confusing. Fix this by inlining the
suspend_complete handlers too.
This is also needed by the next patch that removes a redundant
uninit/init call during system suspend/resume on BXT.
No functional change.
CC: Paulo Zanoni <przanoni@gmail.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Bob Paauwe <bob.j.paauwe@intel.com>
[s/uninline/inline in the commit message]
Link: http://patchwork.freedesktop.org/patch/msgid/1461173277-16090-2-git-send-email-imre.deak@intel.com
In commit 5f304c8736 ("drm/i915/kbl: Reset secondary power well requests
left on by DMC/KVMR") I forgot about the fact that SKL==KBL most of the
time and that a secondary MISC IO power well request left on by the DMC is
"expected". Tune down the corresponding WARN to be a debug message. This
was caught by CI suspend tests.
CC: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1461060036-19043-1-git-send-email-imre.deak@intel.com
It was noticed on bug #94087 that module parameter
i915.edp_vswing=2 that should override the VBT setting
to use default voltage swing (400 mV) was not applied
for Broadwell.
This patch provides a fix for this by checking if default
i.e. higher voltage swing is requested to be used and
applies the DDI translations table for DP instead of eDP
(low vswing) table.
v2: Combine two if statements into one (Jani)
v3: Change dev_priv->edp_low_vswing to use dev_priv->vbt.edp.low_vswing
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=94087
Signed-off-by: Mika Kahola <mika.kahola@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1461155942-7749-1-git-send-email-mika.kahola@intel.com
Cc: stable@vger.kernel.org
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
The newly-introduced function i915_gem_object_pin_map() returns an
ERR_PTR (not NULL) if the pin-and-map opertaion fails, so that's what we
must check for. And it's nicer not to assign such a pointer-or-error to
a structure being filled in until after it's been validated, so we
should keep it local and avoid exporting a bogus pointer. Also, for
clarity and symmetry, we should clear 'virtual_start' along with 'vma'
when unmapping a ringbuffer.
Signed-off-by: Dave Gordon <david.s.gordon@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Now that we keep the GuC client process descriptor permanently mapped,
we don't really need to keep a local copy of the GuC's work-queue-head.
So we can simplify the code a little by not doing this.
Signed-off-by: Alex Dai <yu.dai@intel.com>
Signed-off-by: Dave Gordon <david.s.gordon@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Don't use kmap_atomic() for doorbell & process descriptor access.
This patch fixes the BUG shown below, where the thread could sleep
while holding a kmap_atomic mapping. In order not to need to call
kmap_atomic() in this code path, we now set up a permanent kernel
mapping of the shared doorbell and process-descriptor page, and
use that in all doorbell and process-descriptor related code.
BUG: scheduling while atomic: gem_close_race/1941/0x00000002
Modules linked in: hid_generic usbhid i915 asix usbnet libphy mii
i2c_algo_bit drm_kms_helper cfbfillrect syscopyarea cfbimgblt
sysfillrect sysimgblt fb_sys_fops cfbcopyarea drm coretemp i2c_hid
hid video pinctrl_sunrisepoint pinctrl_intel acpi_pad nls_iso8859_1
e1000e ptp psmouse pps_core ahci libahci
CPU: 0 PID: 1941 Comm: gem_close_race Tainted: G U 4.4.0-160121+ #123
Hardware name: Intel Corporation Skylake Client platform/Skylake AIO
DDR3L RVP10, BIOS SKLSE2R1.R00.X100.B01.1509220551 09/22/2015
0000000000013e40 ffff880166c27a78 ffffffff81280d02 ffff880172c13e40
ffff880166c27a88 ffffffff810c203a ffff880166c27ac8 ffffffff814ec808
ffff88016b7c6000 ffff880166c28000 00000000000f4240 0000000000000001
Call Trace:
[<ffffffff81280d02>] dump_stack+0x4b/0x79
[<ffffffff810c203a>] __schedule_bug+0x41/0x4f
[<ffffffff814ec808>] __schedule+0x5a8/0x690
[<ffffffff814ec927>] schedule+0x37/0x80
[<ffffffff814ef3fd>] schedule_hrtimeout_range_clock+0xad/0x130
[<ffffffff81090be0>] ? hrtimer_init+0x10/0x10
[<ffffffff814ef3f1>] ? schedule_hrtimeout_range_clock+0xa1/0x130
[<ffffffff814ef48e>] schedule_hrtimeout_range+0xe/0x10
[<ffffffff814eef9b>] usleep_range+0x3b/0x40
[<ffffffffa01ec109>] i915_guc_wq_check_space+0x119/0x210 [i915]
[<ffffffffa01da47c>] intel_logical_ring_alloc_request_extras+0x5c/0x70 [i915]
[<ffffffffa01cdbf1>] i915_gem_request_alloc+0x91/0x170 [i915]
[<ffffffffa01c1c07>] i915_gem_do_execbuffer.isra.25+0xbc7/0x12a0 [i915]
[<ffffffffa01cb785>] ? i915_gem_object_get_pages_gtt+0x225/0x3c0 [i915]
[<ffffffffa01d1fb6>] ? i915_gem_pwrite_ioctl+0xd6/0x9f0 [i915]
[<ffffffffa01c2e68>] i915_gem_execbuffer2+0xa8/0x250 [i915]
[<ffffffffa00f65d8>] drm_ioctl+0x258/0x4f0 [drm]
[<ffffffffa01c2dc0>] ? i915_gem_execbuffer+0x340/0x340 [i915]
[<ffffffff8111590d>] do_vfs_ioctl+0x2cd/0x4a0
[<ffffffff8111eac2>] ? __fget+0x72/0xb0
[<ffffffff81115b1c>] SyS_ioctl+0x3c/0x70
[<ffffffff814effd7>] entry_SYSCALL_64_fastpath+0x12/0x6a
------------[ cut here ]------------
v4:
Only tear down doorbell & kunmap() client object if we actually
succeeded in allocating a client object (Tvrtko Ursulin)
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=93847
Original-version-by: Alex Dai <yu.dai@intel.com>
Signed-off-by: Dave Gordon <david.s.gordon@intel.com>
Cc: Tvtrko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Since we can only swap out shmemfs objects, those are the only ones that
can influence the ability of the shrinker to free pages. Currently, all
non-shmemfs objects have a raised pages_pin_count to protect them from
the shrinker, so this just makes the logic for can_release_pages()
clearer (and safer in future so that we don't over estimate our ability
to free up pages from future non-swappable objects).
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1461150592-27818-3-git-send-email-chris@chris-wilson.co.uk
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Inside the shrinker we call can_release_pages() to indicate whether or
not we can make forward progress in freeing up memory by unbinding that
object. When adding our report to oom, we should be using the same
logic.
Whilst here, change the reporting from bytes to pages so that it looks
smaller to the user!, is consistent with the neighbouring oom report
itself which displays counts in pages, and makes the unsigned long
overflow less likely.
v2: Split oversized format string into two lines
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1461150592-27818-2-git-send-email-chris@chris-wilson.co.uk
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
When iterating over the bound list, we expect all objects there to have
their pages pinned (by the bound VMA). So only report those objects with
additional pin count on their pages as "pinned". These should be those
objects used for display and hardware access.
Reported-by: Akash Goel <akash.goel@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Akash Goel <akash.goel@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1461150592-27818-1-git-send-email-chris@chris-wilson.co.uk
Looks like DPF was not implemented for gen8+ but the IER and IMR
are still enabled on initialization.
Since there is no code to handle this interrupt, gate the irq
enablement behind HAS_L3_DPF in case the feature gets enabled
in the future.
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Since commit 30d9aa4265 ("drm/i915: Read sink_count dpcd always"),
the status of a DP connector depends on its sink count value.
However, some eDP panels don't set that value appropriately,
causing them to be reported as disconnected.
Fix this by ignoring sink count for eDP.
v2: Rephrased commit message. (Ander)
In case of eDP, returning status as connected if DPCD
read succeeds to avoid any further operations.
Fixes: 30d9aa4265 ("drm/i915: Read sink_count dpcd always")
Cc: Ander Conselvan De Oliveira <conselvan2@gmail.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Reported-by: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Signed-off-by: Sivakumar Thulasimani <sivakumar.thulasimani@intel.com>
Signed-off-by: Shubhangi Shrivastava <shubhangi.shrivastava@intel.com>
Tested-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Ander Conselvan de Oliveira <conselvan2@gmail.com>
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1460444034-22320-1-git-send-email-shubhangi.shrivastava@intel.com
In commit 7d23e3c37b ("drm/i915: Cleaning up intel_dp_hpd_pulse") some
much needed clean-up was done, but unfortunately part of the change
broke DP MST. The real issue was setting the connector state to
disconnected in the MST case, which is good, but the code then (after
a goto) checks if the connector state is not connected and shuts down
MST if this is the case, which is bad. With this change both SST and
MST seem to be happy.
v2: Add removed check further up in the function to be sure that MST
is shut down when we lose the link. (Ander)
Fixes: commit 7d23e3c37b ("drm/i915: Cleaning up intel_dp_hpd_pulse")
cc: Sivakumar Thulasimani <sivakumar.thulasimani@intel.com>
cc: Shubhangi Shrivastava <shubhangi.shrivastava@intel.com>
cc: Ander Conselvan de Oliveira <conselvan2@gmail.com>
cc: Nathan D Ciobanu <nathan.d.ciobanu@intel.com>
Signed-off-by: Jim Bride <jim.bride@linux.intel.com>
Reviewed-by: Ander Conselvan de Oliveira <conselvan2@gmail.com>
Reviewed-by: Lyude <cpaul@redhat.com>
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1460394684-7036-1-git-send-email-jim.bride@linux.intel.com
Do not use magic numbers, do not prefix stuff with "PCI_", do not
declare registers in implementation files. Also move the PCI
registers under correct comment in i915_reg.h.
v2:
- Consistently use BSM (not BDSM or other variants from PRM) (Chris)
- Also include register address to help identify the register (Chris)
v3:
- Refer to register value as *_val instead of *_reg (Chris)
v4:
- Make style checker happy
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
We need to kunmap pt_vaddr and not pt itself, otherwise we end up
mapping a bunch of pages without ever unmapping them.
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Fixes: d1c54acd67 ("drm/i915/gtt: Introduce kmap|kunmap for dma page")
Signed-off-by: Matthew Auld <matthew.auld@intel.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1460476663-24890-4-git-send-email-matthew.auld@intel.com
The power cycle delay starts _after_ turning off the panel power. Do the
msleep after frobbing the pmic panel power gpio.
Also toss in a FIXME about optimizing away needless waits.
Cc: Shobhit Kumar <shobhit.kumar@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Fixes: fc45e82199 ("drm/i915: Use the CRC gpio for panel enable/disable")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1460996271-29795-1-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Shobhit Kumar <shobhit.kumar@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Currently we're trying to define HSW/BDW power wells by what's not
included. Let's do it the other way around, so that you can actually
tell when the power well would get enabled. This will also allow us to
add new power domains without accidentally adding it to the HSW/BDW
display power domains.
The current set of domains looks rather buggy even:
- POWER_DOMAIN_MODESET is included in the display power well needlessly
- DDI-B to DDI-E were not part of the display power well when they
should be
So let's fix that up while at it.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1460977348-32260-4-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>
Currently we're using POWER_DOMAIN_MASK as the power domains for the
display power well on VLV/CHV. That includes all power domains even
though the disp2d/pipe-a power well is not needed for a lot of things.
Let's reduce these to what we actually need.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1460977348-32260-3-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>
While we disable runtime PM and with that display power well support if
the DMC firmware isn't loaded, we still want to disable power wells
during system suspend and driver unload. So drop/reacquire the
corresponding power refcount during suspend/resume and driver unloading.
This also means we have to check if DMC is not loaded and skip enabling
DC states in the power well code.
v2:
- Reuse intel_csr_ucode_suspend() in intel_csr_ucode_fini() instead of
opencoding the former. (Chris)
- Add docbook comment to the public resume and suspend functions.
CC: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/1460980101-14713-1-git-send-email-imre.deak@intel.com
The driver's VDD on/off logic assumes that whenever the VDD is on we
also hold an AUX power domain reference. Since BIOS can leave the VDD on
during booting and resuming and on DDI platforms we won't take a
corresponding power reference, the above assumption won't hold on those
platforms and an eventual delayed VDD off work will do an extraneous AUX
power domain put resulting in a refcount underflow. Fix this the same
way we did this for non-DDI DP encoders:
commit 6d93c0c417 ("drm/i915: fix VDD state tracking after system
resume")
At the same time call the DP encoder suspend handler the same way as the
non-DDI DP encoders do to flush any pending VDD off work. Leaving the
work running may cause a HW access where we don't expect this (at a point
where power domains are suspended already).
While at it remove an unnecessary function call indirection.
This fixed for me AUX refcount underflow problems on BXT during
suspend/resume.
CC: Ville Syrjälä <ville.syrjala@linux.intel.com>
CC: stable@vger.kernel.org
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1460963062-13211-4-git-send-email-imre.deak@intel.com
