On a read error, e1000e might have returned uninitialized block of
eeprom data back to userspace. The convention is that 0xff is "empty",
so mark the entire eeprom as empty in case of an error.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This patch adds support for the BM PHY, a new PHY model being used
on ICH9-based implementations.
This new PHY exposes issues in the ICH9 silicon when receiving
jumbo frames large enough to use more than a certain part of the
Rx FIFO, and this unfortunately breaks packet split jumbo receives.
For this reason we re-introduce (for affected adapters only) the
jumbo single-skb receive routine back so that people who do
wish to use jumbo frames on these ich9 platforms can do so.
Part of this problem has to do with CPU sleep states and to make
sure that all the wake up timings are correctly we force them
with the recently merged pm_qos infrastructure written by Mark
Gross. (See http://lkml.org/lkml/2007/10/4/400).
To make code read a bit easier we introduce a _IS_ICH flag so
that we don't need to do mac type checks over the code.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
To enable EEH support for pci-express network adapters, pcie/msi state
needs to be saved and restored for that adapter.
Tested this EEH patch with 2ports and 4ports pci-express e1000e
adapters.
Signed-off-by: Wendy Xiong <wendyx@us.ibm.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The lower limit of 80 descriptors in the ring is only valid for
one older 8254x chipset. All e1000e devices can use as low as
64 descriptors.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Several components to this complex fix. The es2lan cards occasionally
gave a "HW Error" especially when forcing speed. Some users also
reported that the BMC stole ARP packets.
The fixes include setting the proper SW_FW bits to tell the BMC
that we're active and not do any un-initialization at all, so the
setup routine is largely changed.
Signed-off-by: David Graham <david.graham@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The ethtool -c / -C interface can now be used to modify the
irq moderation algorithm. This change does not require an
adapter reset and can thus be used at all times. The adapter
only supports changing/reading rx-usecs which has special
values for 0, 1 and 3:
0 - no irq moderation whatsoever
1 - normal moderation favoring regular mixed traffic (default)
3 - best attempt at low latency possible at cost of CPU
For values between 10 and 10000 the rx-usecs defines "the minimum
time between successive irqs" in usec, unlike the module parameter.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Several stats registers are completely unused and we just waste pci
bus time reading them. We also omit using the high 32 bits of the GORC/
GOTC counters. We can just read clear them and only read the low registers.
Mii-tool can also break es2lan if it executes a MII PHY register
ioctl while the device is in autonegotiation. Unfortunately it seems
that several applications and installations still perform this ioctl
call periodically and especially in this crucial startup time. We
can fool the ioctl by providing fail safe information that mimics
the "down" link state and only perform the dangerous PHY reads once
after link comes up to fill in the real values. As long as link
stays up the information will not change.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The register tests should be run with all the proper flags enabled
to maximize the test coverage code and make sure we are as close
as we can get to testing regular traffic.
Reformat the code for readability. Minor cleanups in the descriptor
ring setup.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Several minor cosmetic function renames.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
With multiple queues coming into the code these base control
registers need to be made into arrays.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This reorganization moves the PHY status into a separate
struct. Flow Control setup is moved into this struct as well
and frame size away from here into the adapter struct where its
inly use is.
The post-link-up code is now a separate function and moved out
of the watchdog function itself. This allows us to track the
es2lan restart issue a bit easier.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Rename this function to be consistent with function naming (verb first)
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Adjusting the comment blocks here to be code-style compliant. no
code changes.
Changed some copyright dates to 2008.
Indentation fixes.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
irq_sem can safely be removed by auditing all irq.*able sites to
make sure that interrupts don't get enabled unexpectedly when the
interface is down.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This function is no longer used now that 82573 uses the eerd
read method as well. Thanks to Adrian Bunk for pointing this out.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Fix some spelling errors and inconsistencies in comment blocks.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
this patch avoids a denial of service from an evildoer sending a
continuous stream of flow control at our adapter that is plugged
into a non-flow control enabled switch.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This simplifies the 82571/2/3 family initialization a bit
and removes an initialization table no longer needed.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Users reported that ARP's were lost with e1000e. The problem
is fixed by not enabling this manageability configuration
bit.
None of the release_manageability code is actually needed as the
normal device reset during a shutdown returns everthing to
the right condition automatically.
Signed-off-by: David Graham <david.graham@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
CRC stripping was only correctly enabled for packet split recieves
which is used when receiving jumbo frames. Correctly enable SECRC
also for normal buffer packet receives.
Tested by Andy Gospodarek and Johan Andersson, see bugzilla #9940.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
A logic mishap caused the adapter to keep link while we can
disable it due to WoL not being active, and vice versa.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
There's too much noise on systems that don't support MSI. Let's get rid
of a few and make the real error message more specific.
Signed-off-by: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch makes the needlessly global reg_pattern_test_array() static.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ethtool supports wake-on-ARP and wake-on-link, and so does the hardware
supported by e1000e. This patch just introduces the two.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add functions for reg_pattern_test and reg_set_and check
Changed macros to use these functions
Compiled x86, untested
Size decreased ~2K
old:
$ size drivers/net/e1000e/ethtool.o
text data bss dec hex filename
14461 0 0 14461 387d drivers/net/e1000e/ethtool.o
new:
$ size drivers/net/e1000e/ethtool.o
text data bss dec hex filename
12498 0 0 12498 30d2 drivers/net/e1000e/ethtool.o
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
formerly e1000/e1000e only updated traffic counters once every
2 seconds with the register values of bytes/packets. With newer
code however in the interrupt and polling code we can real-time
fill in these values in the netstats struct for users to see.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
e1000e will from now on support the PCI-Express adapters that
previously were supported by e1000. This support means better
performance and easier debugging from now on for both the old
PCI-X/PCI hardware and PCI-Express adapters.
This patch also moves 3 recently merged device IDs over to e1000e
that are identical to quad-port versions of already existing
dual port versions. With this last bit every former e1000 pci-e
device should work now with e1000e.
Here is a brief list of which gigabit driver to use with which
adapter:
e1000:
82540 -> 82547
e1000e:
82571 -> 82573
ich8, ich9 (82562 or 82566)
es2lan (80003eslan)
igb: (not yet merged, only available from e1000.sf.net)
82575
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
L1 ASPM link (pci-e link power savings) has significant benefits
(~1W savings when link is active) but unfortunately does not work
correctly on any of the chipsets that have 82573 on mobile platforms
which causes various nuisances:
- eeprom reads return garbage information leading to bad eeprom
checksums
- long ping times (up to 2 seconds)
- complete system hangs (freeze/lockup)
A lot of T60 owners have been plagued by this, but other mobile
solutions also suffer from these symptoms.
Disabling L1 ASPM before we activate the PCI-E link fixes all of
these issues at the cost of some power consumption.
Remove a workaround RDTR adjustment that is no longer needed with
this new one.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Port alternate MAC address support from the sourceforge
e1000 driver to the upstream e1000e driver.
Signed-off-by: Bill Hayes <bill.hayes@hp.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Using ARRAY_SIZE() on arrays of the form array[][K] makes it unnecessary
to know the value of K when checking its size.
Signed-off-by: Alejandro Martinez Ruiz <alex@flawedcode.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Several of the Intel ethernet drivers keep an atomic counter used to
manage when to actually hit the hardware with a disable or an enable.
The way the net_rx_work() breakout logic works during a pending
napi_disable() is that it simply unschedules the poll even if it
still has work.
This can potentially leave interrupts disabled, but that is OK
because all of the drivers are about to disable interrupts
anyways in all such code paths that do a napi_disable().
Unfortunately, this trips up the semaphore used here in the Intel
drivers. If you hit this case, when you try to bring the interface
back up it won't enable interrupts. A reload of the driver module
fixes it of course.
So what we do is make sure all the sequences now go:
napi_disable();
atomic_set(&adapter->irq_sem, 0);
*_irq_disable();
which makes sure the counter is always in the correct state.
Reported by Robert Olsson.
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes a regression added by changeset
53e52c729c ("[NET]: Make ->poll()
breakout consistent in Intel ethernet drivers.")
As pointed out by Jesse Brandeburg, for three of the drivers edited
above there is breakout logic in the *_clean_tx_irq() code to prevent
running TX reclaim forever. If this occurs, we have to elide NAPI
poll completion or else those TX events will never be serviced.
Signed-off-by: David S. Miller <davem@davemloft.net>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
This makes the ->poll() routines of the E100, E1000, E1000E, IXGB, and
IXGBE drivers complete ->poll() consistently.
Now they will all break out when the amount of RX work done is less
than 'budget'.
At a later time, we may want put back code to include the TX work as
well (as at least one other NAPI driver does, but by in large NAPI
drivers do not do this). But if so, it should be done consistently
across the board to all of these drivers.
Signed-off-by: David S. Miller <davem@davemloft.net>
Acked-by: Auke Kok <auke-jan.h.kok@intel.com>
Drivers do this to try to break out of the ->poll()'ing loop
when the device is being brought administratively down.
Now that we have a napi_disable() "pending" state we are going
to solve that problem generically.
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix sparse warnings from e1000e driver in net-2.6.24.
Added a sparse fix for module param arrays which can have int values
but only the array index needs to be unsigned. --Auke
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The legacy jumbo frame receive code is no longer needed since all
hardware can do packet split and we're no longer offering a bypass
kernel config option to disable packet split. Remove the unused code.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This workaround code performed software stripping instead of the
hardware which can do it much faster. None of the e1000e target
hardware has issues with this feature and should work fine. This
gives us some performance back on receive, and removes some
kludging stripping the 4 bytes.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Upon inspection the rx FIFO size calculation code was found to have
2 significant flaws: A superfluous minus sign resulting in the
wrong size to be used for jumbo frames on 82573 and ich9, as well
as that this code rewrote the read-only adapter->pba variable
resulting in different values at each run.
Without this patch jumbo's will work but performance will be
awkward since the TX size is not adequate for two whole frames.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Fix allocation and freeing of jumbo frames where several bugs
were recently introduced by cleanups after we forked this code
from e1000. This moves ps_pages to buffer_info where it really
belongs and makes it a dynamically allocated array. The penalty
is not that high since it's allocated outside of the buffer_info
struct anyway.
Without this patch all jumbo frames are completely broken and the
driver panics.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Apparently poking the link status registers when autonegotiation
is running on the PHY might botch the PHY link on 80003es2lan
devices. While this is a very rare condition we can completely
avoid it alltogether by just using the MAC link bits to provide
the proper information to ethtool.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Spotted by the Coverity checker.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
After a cable unplug the forced flow control settings were lost
accidentally and the flow control settings fell back to the default
EEPROM determined values. This breaks for people who want to
run without fc enabled - after a cable reset the driver would
refuse to run with fc disabled.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
After an e1000 patch from Krishna Kumar <krkumar2@in.ibm.com>.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
A merge/cleanup code accidentally dropped 8254x code in and removed
8257x code here. Undo this mistake and use the pci-e relevant register
test similar as to what is in e1000.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
A small bug crawled in the -DDEBUG enabled code. Fix this to
properly call the backreference device name.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Returning BUSY will make qdisc_restart enqueue the skb which was already
freed. The bad skb was correctly freed and we should return NETDEV_TX_OK.
First spotted by Jeff Garzik on 08/13/07.
Signed-off-by: Krishna Kumar <krkumar2@in.ibm.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
These have been superceded by the new ->get_sset_count() hook.
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
It's been a useless no-op for long enough in 2.6 so I figured it's time to
remove it. The number of people that could object because they're
maintaining unified 2.4 and 2.6 drivers is probably rather small.
[ Handled drivers added by netdev tree and some missed IRDA cases... -DaveM ]
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This driver implements support for the ICH9 on-board LAN ethernet
device. The device is similar to ICH8.
The driver encompasses code to support 82571/2/3, es2lan and ICH8
devices as well, but those device IDs are disabled and will be
"lifted" from the e1000 driver over one at a time once this driver
receives some more live time.
Changes to the last snapshot posted are exclusively in the internal
hardware API organization. Many thanks to Jeff Garzik for jumping in
and getting this organized with a keen eye on the future layout.
[ Integrated napi_struct patch from Auke as well... -DaveM ]
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
