The eeh_ops->probe() function is called from two different contexts:
1. On pseries, where we set EEH_PROBE_MODE_DEVTREE, it's called in
eeh_add_device_early() which is supposed to run before we create
a pci_dev.
2. On PowerNV, where we set EEH_PROBE_MODE_DEV, it's called in
eeh_device_add_late() which is supposed to run *after* the
pci_dev is created.
The "early" probe is required because PAPR requires that we perform an RTAS
call to enable EEH support on a device before we start interacting with it
via config space or MMIO. This requirement doesn't exist on PowerNV and
shoehorning two completely separate initialisation paths into a common
interface just results in a convoluted code everywhere.
Additionally the early probe requires the probe function to take an pci_dn
rather than a pci_dev argument. We'd like to make pci_dn a pseries specific
data structure since there's no real requirement for them on PowerNV. To
help both goals move the early probe into the pseries containment zone
so the platform depedence is more explicit.
Reviewed-by: Sam Bobroff <sbobroff@linux.ibm.com>
Signed-off-by: Oliver O'Halloran <oohall@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200306073904.4737-5-oohall@gmail.com
This check for a missing PHB has existing in various forms since the
initial PPC64 port was upstreamed in 2002. The idea seems to be that we
need to guard against creating pci-specific data structures for the non-pci
children of a PCI device tree node (e.g. USB devices). However, we only
create pci_dn structures for DT nodes that correspond to PCI devices so
there's not much point in doing this check in the eeh_probe path.
Reviewed-by: Sam Bobroff <sbobroff@linux.ibm.com>
Signed-off-by: Oliver O'Halloran <oohall@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200306073904.4737-4-oohall@gmail.com
The pci hotplug helper (pci_hp_add_devices()) calls
eeh_add_device_tree_early() to scan the device-tree for new PCI devices and
do the early EEH probe before the device is scanned. This early probe is a
no-op in a lot of cases because:
a) The early init is only required to satisfy a PAPR requirement that EEH
be configured before we start doing config accesses. On PowerNV it is
a no-op.
b) It's a no-op for devices that have already had their eeh_dev
initialised.
There are four callers of pci_hp_add_devices():
1. arch/powerpc/kernel/eeh_driver.c
Here the hotplug helper is called when re-scanning pci_devs that
were removed during an EEH recovery pass. The EEH stat for each
removed device (the eeh_dev) is retained across a recovery pass
so the early init is a no-op in this case.
2. drivers/pci/hotplug/pnv_php.c
This is also a no-op since the PowerNV hotplug driver is, suprisingly,
PowerNV specific.
3. drivers/pci/hotplug/rpaphp_core.c
4. drivers/pci/hotplug/rpaphp_pci.c
In these two cases new devices have been hotplugged and FW has
provided new DT nodes for each. These are the only two cases where
the EEH we might have new PCI device nodes in the DT so these are
the only two cases where the early EEH probe needs to be done.
We can move the calls to eeh_add_device_tree_early() to the locations where
it's needed and remove it from the generic path. This is preparation for
making the early EEH probe pseries specific.
Reviewed-by: Sam Bobroff <sbobroff@linux.ibm.com>
Signed-off-by: Oliver O'Halloran <oohall@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200306073904.4737-3-oohall@gmail.com
On pseries and PowerNV pcibios_bus_add_device() calls eeh_add_device_late()
so there's no need to do a separate tree traversal to bind the eeh_dev and
pci_dev together setting up the PHB at boot. As a result we can remove
eeh_add_device_tree_late().
Reviewed-by: Sam Bobroff <sbobroff@linux.ibm.com>
Signed-off-by: Oliver O'Halloran <oohall@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200306073904.4737-2-oohall@gmail.com
Move creating the EEH specific sysfs files into eeh_add_device_late()
rather than being open-coded all over the place. Calling the function is
generally done immediately after calling eeh_add_device_late() anyway. This
is also a correctness fix since currently the sysfs files will be added
even if the EEH probe happens to fail.
Similarly, on pseries we currently add the sysfs files before calling
eeh_add_device_late(). This is flat-out broken since the sysfs files
require the pci_dev->dev.archdata.edev pointer to be set, and that is done
in eeh_add_device_late().
Reviewed-by: Sam Bobroff <sbobroff@linux.ibm.com>
Signed-off-by: Oliver O'Halloran <oohall@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200306073904.4737-1-oohall@gmail.com
The previous commit reduced the amount of code that is run before we
setup a paca. However there are still a few remaining functions that
run with no paca, or worse, with an arbitrary value in r13 that will
be used as a paca pointer.
In particular the stack protector canary is stored in the paca, so if
stack protector is activated for any of these functions we will read
the stack canary from wherever r13 points. If r13 happens to point
outside of memory we will get a machine check / checkstop.
For example if we modify initialise_paca() to trigger stack
protection, and then boot in the mambo simulator with r13 poisoned in
skiboot before calling the kernel:
DEBUG: 19952232: (19952232): INSTRUCTION: PC=0xC0000000191FC1E8: [0x3C4C006D]: addis r2,r12,0x6D [fetch]
DEBUG: 19952236: (19952236): INSTRUCTION: PC=0xC00000001807EAD8: [0x7D8802A6]: mflr r12 [fetch]
FATAL ERROR: 19952276: (19952276): Check Stop for 0:0: Machine Check with ME bit of MSR off
DEBUG: 19952276: (19952276): INSTRUCTION: PC=0xC0000000191FCA7C: [0xE90D0CF8]: ld r8,0xCF8(r13) [Instruction Failed]
INFO: 19952276: (19952277): ** Execution stopped: Mambo Error, Machine Check Stop, **
systemsim % bt
pc: 0xC0000000191FCA7C initialise_paca+0x54
lr: 0xC0000000191FC22C early_setup+0x44
stack:0x00000000198CBED0 0x0 +0x0
stack:0x00000000198CBF00 0xC0000000191FC22C early_setup+0x44
stack:0x00000000198CBF90 0x1801C968 +0x1801C968
So annotate the relevant functions to ensure stack protection is never
enabled for them.
Fixes: 06ec27aea9 ("powerpc/64: add stack protector support")
Cc: stable@vger.kernel.org # v4.20+
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200320032116.1024773-2-mpe@ellerman.id.au
Currently we set up the paca after parsing the device tree for CPU
features. Prior to that, r13 contains random data, which means there
is random data in r13 while we're running the generic dt parsing code.
This random data varies depending on whether we boot through a vmlinux
or a zImage: for the vmlinux case it's usually around zero, but for
zImages we see random values like 912a72603d420015.
This is poor practice, and can also lead to difficult-to-debug
crashes. For example, when kcov is enabled, the kcov instrumentation
attempts to read preempt_count out of the current task, which goes via
the paca. This then crashes in the zImage case.
Similarly stack protector can cause crashes if r13 is bogus, by
reading from the stack canary in the paca.
To resolve this:
- move the paca setup to before the CPU feature parsing.
- because we no longer have access to CPU feature flags in paca
setup, change the HV feature test in the paca setup path to consider
the actual value of the MSR rather than the CPU feature.
Translations get switched on once we leave early_setup, so I think
we'd already catch any other cases where the paca or task aren't set
up.
Boot tested on a P9 guest and host.
Fixes: fb0b0a73b2 ("powerpc: Enable kcov")
Fixes: 06ec27aea9 ("powerpc/64: add stack protector support")
Cc: stable@vger.kernel.org # v4.20+
Reviewed-by: Andrew Donnellan <ajd@linux.ibm.com>
Suggested-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Daniel Axtens <dja@axtens.net>
[mpe: Reword comments & change log a bit to mention stack protector]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200320032116.1024773-1-mpe@ellerman.id.au
H_PAGE_THP_HUGE is used to differentiate between a THP hugepage and
hugetlb hugepage entries. The difference is WRT how we handle hash
fault on these address. THP address enables MPSS in segments. We want
to manage devmap hugepage entries similar to THP pt entries. Hence use
H_PAGE_THP_HUGE for devmap huge PTE entries.
With current code while handling hash PTE fault, we do set is_thp =
true when finding devmap PTE huge PTE entries.
Current code also does the below sequence we setting up huge devmap
entries.
entry = pmd_mkhuge(pfn_t_pmd(pfn, prot));
if (pfn_t_devmap(pfn))
entry = pmd_mkdevmap(entry);
In that case we would find both H_PAGE_THP_HUGE and PAGE_DEVMAP set
for huge devmap PTE entries. This results in false positive error like
below.
kernel BUG at /home/kvaneesh/src/linux/mm/memory.c:4321!
Oops: Exception in kernel mode, sig: 5 [#1]
LE PAGE_SIZE=64K MMU=Hash SMP NR_CPUS=2048 NUMA pSeries
Modules linked in:
CPU: 56 PID: 67996 Comm: t_mmap_dio Not tainted 5.6.0-rc4-59640-g371c804dedbc #128
....
NIP [c00000000044c9e4] __follow_pte_pmd+0x264/0x900
LR [c0000000005d45f8] dax_writeback_one+0x1a8/0x740
Call Trace:
str_spec.74809+0x22ffb4/0x2d116c (unreliable)
dax_writeback_one+0x1a8/0x740
dax_writeback_mapping_range+0x26c/0x700
ext4_dax_writepages+0x150/0x5a0
do_writepages+0x68/0x180
__filemap_fdatawrite_range+0x138/0x180
file_write_and_wait_range+0xa4/0x110
ext4_sync_file+0x370/0x6e0
vfs_fsync_range+0x70/0xf0
sys_msync+0x220/0x2e0
system_call+0x5c/0x68
This is because our pmd_trans_huge check doesn't exclude _PAGE_DEVMAP.
To make this all consistent, update pmd_mkdevmap to set
H_PAGE_THP_HUGE and pmd_trans_huge check now excludes _PAGE_DEVMAP
correctly.
Fixes: ebd3119793 ("powerpc/mm: Add devmap support for ppc64")
Cc: stable@vger.kernel.org # v4.13+
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200313094842.351830-1-aneesh.kumar@linux.ibm.com
Reorder Linux PTE bits to (almost) match Hash PTE bits.
RW Kernel : PP = 00
RO Kernel : PP = 00
RW User : PP = 01
RO User : PP = 11
So naturally, we should have
_PAGE_USER = 0x001
_PAGE_RW = 0x002
Today 0x001 and 0x002 and _PAGE_PRESENT and _PAGE_HASHPTE which
both are software only bits.
Switch _PAGE_USER and _PAGE_PRESET
Switch _PAGE_RW and _PAGE_HASHPTE
This allows to remove a few insns.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/c4d6c18a7f8d9d3b899bc492f55fbc40ef38896a.1583861325.git.christophe.leroy@c-s.fr
At the time being we have something like
if (something) {
p = get();
if (p) {
if (something_wrong)
goto out;
...
return;
} else if (a != b) {
if (some_error)
goto out;
...
}
goto out;
}
p = get();
if (!p) {
if (a != b) {
if (some_error)
goto out;
...
}
goto out;
}
This is similar to
p = get();
if (!p) {
if (a != b) {
if (some_error)
goto out;
...
}
goto out;
}
if (something) {
if (something_wrong)
goto out;
...
return;
}
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
[mpe: Reflow the comment that was moved]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/07a17425743600460ce35fa9432d42487a825583.1582099499.git.christophe.leroy@c-s.fr
We currently have two section mismatch warnings:
The function __boot_from_prom() references
the function __init prom_init().
The function start_here_common() references
the function __init start_kernel().
The warnings are correct, we do have branches from non-init code into
init code, which is freed after boot. But we don't expect to ever
execute any of that early boot code after boot, if we did that would
be a bug. In particular calling into OF after boot would be fatal
because OF is no longer resident.
So for now fix the warnings by marking the relevant functions as
__REF, which puts them in the ".ref.text" section.
This causes some reordering of the functions in the final link:
@@ -217,10 +217,9 @@
c00000000000b088 t generic_secondary_common_init
c00000000000b124 t __mmu_off
c00000000000b14c t __start_initialization_multiplatform
-c00000000000b1ac t __boot_from_prom
-c00000000000b1ec t __after_prom_start
-c00000000000b260 t p_end
-c00000000000b27c T copy_and_flush
+c00000000000b1ac t __after_prom_start
+c00000000000b220 t p_end
+c00000000000b23c T copy_and_flush
c00000000000b300 T __secondary_start
c00000000000b300 t copy_to_here
c00000000000b344 t start_secondary_prolog
@@ -228,8 +227,9 @@
c00000000000b36c t enable_64b_mode
c00000000000b388 T relative_toc
c00000000000b3a8 t p_toc
-c00000000000b3b0 t start_here_common
-c00000000000b3d0 t start_here_multiplatform
+c00000000000b3b0 t __boot_from_prom
+c00000000000b3f0 t start_here_multiplatform
+c00000000000b480 t start_here_common
c00000000000b880 T system_call_common
c00000000000b974 t system_call
c00000000000b9dc t system_call_exit
In particular __boot_from_prom moves after copy_to_here, which means
it's not copied to zero in the first stage of copy of the kernel to
zero.
But that's OK, because we only call __boot_from_prom before we do the
copy, so it makes no difference when it's copied. The call sequence
is:
__start
-> __start_initialization_multiplatform
-> __boot_from_prom
-> __start
-> __start_initialization_multiplatform
-> __after_prom_start
-> copy_and_flush
-> copy_and_flush (relocated to 0)
-> start_here_multiplatform
-> early_setup
Reported-by: Mauricio Faria de Oliveira <mauricfo@linux.ibm.com>
Reported-by: Roman Bolshakov <r.bolshakov@yadro.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200225031328.14676-1-mpe@ellerman.id.au
In xmon we have two variables that are used by the dump commands.
There's ndump which is the number of bytes to dump using 'd', and
nidump which is the number of instructions to dump using 'di'.
ndump starts as 64 and nidump starts as 16, but both can be set by the
user.
It's fairly common to be pasting addresses into xmon when trying to
debug something, and if you inadvertently double paste an address like
so:
0:mon> di c000000002101f6c c000000002101f6c
The second value is interpreted as the number of instructions to dump.
Luckily it doesn't dump 13 quintrillion instructions, the value is
limited to MAX_DUMP (128K). But as each instruction is dumped on a
single line, that's still a lot of output. If you're on a slow console
that can take multiple minutes to print. If you were "just popping in
and out of xmon quickly before the RCU/hardlockup detector fires" you
are now having a bad day.
Things are not as bad with 'd' because we print 16 bytes per line, so
it's fewer lines. But it's still quite a lot.
So shrink the maximum for 'd' to 64K (one page), which is 4096 lines.
For 'di' add a new limit which is the above / 4 - because instructions
are 4 bytes, meaning again we can dump one page.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200219110007.31195-1-mpe@ellerman.id.au
The "os-term" RTAS calls has one argument with a message address of OS
termination cause. rtas_os_term() already passes it but the recently
added prom_init's version of that missed it; it also does not fill
args correctly.
This passes the message address and initializes the number of arguments.
Fixes: 6a9c930bd7 ("powerpc/prom_init: Add the ESM call to prom_init")
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200312074404.87293-1-aik@ozlabs.ru
ld instruction should have 14 bit immediate field (DS) concatenated
with 0b00 on the right, encode it accordingly. Introduce macro
`IMM_DS()` to encode DS form instructions with 14 bit immediate field.
Fixes: 4ceae137bd ("powerpc: emulate_step() tests for load/store instructions")
Reviewed-by: Sandipan Das <sandipan@linux.ibm.com>
Signed-off-by: Balamuruhan S <bala24@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200311102405.392263-1-bala24@linux.ibm.com
The expectation is that when calling of_read_drc_info_cell()
repeatedly to parse multiple drc-info records that the in/out curval
parameter points at the start of the next record on return. However,
the current behavior has curval still pointing at the final value of
the record just parsed. The result of which is that if the
ibm,drc-info property contains multiple properties the parsed value
of the drc_type for any record after the first has the power_domain
value of the previous record appended to the type string.
eg: observed the following 0xffffffff prepended to PHB
drc-info: type: \xff\xff\xff\xffPHB, prefix: PHB , index_start: 0x20000001
drc-info: suffix_start: 1, sequential_elems: 3072, sequential_inc: 1
drc-info: power-domain: 0xffffffff, last_index: 0x20000c00
In practice PHBs are the only type of connector in the ibm,drc-info
property that has multiple records. So, it breaks PHB hotplug, but by
chance not PCI, CPU, slot, or memory because they happen to only ever
be a single record.
Fix by incrementing curval past the power_domain value to point at
drc_type string of next record.
Fixes: e83636ac33 ("pseries/drc-info: Search DRC properties for CPU indexes")
Signed-off-by: Tyrel Datwyler <tyreld@linux.ibm.com>
Acked-by: Nathan Lynch <nathanl@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200307024547.5748-1-tyreld@linux.ibm.com
When the call to UV_REGISTER_MEM_SLOT is failing, for instance because
there is not enough free secured memory, the Hypervisor (HV) has to call
UV_RETURN to report the error to the Ultravisor (UV). Then the UV will call
H_SVM_INIT_ABORT to abort the securing phase and go back to the calling VM.
If the kvm->arch.secure_guest is not set, in the return path rfid is called
but there is no valid context to get back to the SVM since the Hcall has
been routed by the Ultravisor.
Move the setting of kvm->arch.secure_guest earlier in
kvmppc_h_svm_init_start() so in the return path, UV_RETURN will be called
instead of rfid.
Cc: Bharata B Rao <bharata@linux.ibm.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Laurent Dufour <ldufour@linux.ibm.com>
Reviewed-by: Ram Pai <linuxram@us.ibm.com>
Tested-by: Fabiano Rosas <farosas@linux.ibm.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
The Hcall named H_SVM_* are reserved to the Ultravisor. However, nothing
prevent a malicious VM or SVM to call them. This could lead to weird result
and should be filtered out.
Checking the Secure bit of the calling MSR ensure that the call is coming
from either the Ultravisor or a SVM. But any system call made from a SVM
are going through the Ultravisor, and the Ultravisor should filter out
these malicious call. This way, only the Ultravisor is able to make such a
Hcall.
Cc: Bharata B Rao <bharata@linux.ibm.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Laurent Dufour <ldufour@linux.ibm.com>
Reviewed-by: Ram Pai <linuxram@us.ibnm.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
The PS3 notification interrupt and kthread use a hacked up completion to
communicate. Since we're wanting to change the completion implementation and
this is abuse anyway, replace it with a simple rcuwait since there is only ever
the one waiter.
AFAICT the kthread uses TASK_INTERRUPTIBLE to not increase loadavg, kthreads
cannot receive signals by default and this one doesn't look different. Use
TASK_IDLE instead.
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lkml.kernel.org/r/20200321113241.930037873@linutronix.de
With PR KVM, shutting down a VM causes the host kernel to crash:
[ 314.219284] BUG: Unable to handle kernel data access on read at 0xc00800000176c638
[ 314.219299] Faulting instruction address: 0xc008000000d4ddb0
cpu 0x0: Vector: 300 (Data Access) at [c00000036da077a0]
pc: c008000000d4ddb0: kvmppc_mmu_pte_flush_all+0x68/0xd0 [kvm_pr]
lr: c008000000d4dd94: kvmppc_mmu_pte_flush_all+0x4c/0xd0 [kvm_pr]
sp: c00000036da07a30
msr: 900000010280b033
dar: c00800000176c638
dsisr: 40000000
current = 0xc00000036d4c0000
paca = 0xc000000001a00000 irqmask: 0x03 irq_happened: 0x01
pid = 1992, comm = qemu-system-ppc
Linux version 5.6.0-master-gku+ (greg@palmb) (gcc version 7.5.0 (Ubuntu 7.5.0-3ubuntu1~18.04)) #17 SMP Wed Mar 18 13:49:29 CET 2020
enter ? for help
[c00000036da07ab0] c008000000d4fbe0 kvmppc_mmu_destroy_pr+0x28/0x60 [kvm_pr]
[c00000036da07ae0] c0080000009eab8c kvmppc_mmu_destroy+0x34/0x50 [kvm]
[c00000036da07b00] c0080000009e50c0 kvm_arch_vcpu_destroy+0x108/0x140 [kvm]
[c00000036da07b30] c0080000009d1b50 kvm_vcpu_destroy+0x28/0x80 [kvm]
[c00000036da07b60] c0080000009e4434 kvm_arch_destroy_vm+0xbc/0x190 [kvm]
[c00000036da07ba0] c0080000009d9c2c kvm_put_kvm+0x1d4/0x3f0 [kvm]
[c00000036da07c00] c0080000009da760 kvm_vm_release+0x38/0x60 [kvm]
[c00000036da07c30] c000000000420be0 __fput+0xe0/0x310
[c00000036da07c90] c0000000001747a0 task_work_run+0x150/0x1c0
[c00000036da07cf0] c00000000014896c do_exit+0x44c/0xd00
[c00000036da07dc0] c0000000001492f4 do_group_exit+0x64/0xd0
[c00000036da07e00] c000000000149384 sys_exit_group+0x24/0x30
[c00000036da07e20] c00000000000b9d0 system_call+0x5c/0x68
This is caused by a use-after-free in kvmppc_mmu_pte_flush_all()
which dereferences vcpu->arch.book3s which was previously freed by
kvmppc_core_vcpu_free_pr(). This happens because kvmppc_mmu_destroy()
is called after kvmppc_core_vcpu_free() since commit ff030fdf55
("KVM: PPC: Move kvm_vcpu_init() invocation to common code").
The kvmppc_mmu_destroy() helper calls one of the following depending
on the KVM backend:
- kvmppc_mmu_destroy_hv() which does nothing (Book3s HV)
- kvmppc_mmu_destroy_pr() which undoes the effects of
kvmppc_mmu_init() (Book3s PR 32-bit)
- kvmppc_mmu_destroy_pr() which undoes the effects of
kvmppc_mmu_init() (Book3s PR 64-bit)
- kvmppc_mmu_destroy_e500() which does nothing (BookE e500/e500mc)
It turns out that this is only relevant to PR KVM actually. And both
32 and 64 backends need vcpu->arch.book3s to be valid when calling
kvmppc_mmu_destroy_pr(). So instead of calling kvmppc_mmu_destroy()
from kvm_arch_vcpu_destroy(), call kvmppc_mmu_destroy_pr() at the
beginning of kvmppc_core_vcpu_free_pr(). This is consistent with
kvmppc_mmu_init() being the last call in kvmppc_core_vcpu_create_pr().
For the same reason, if kvmppc_core_vcpu_create_pr() returns an
error then this means that kvmppc_mmu_init() was either not called
or failed, in which case kvmppc_mmu_destroy() should not be called.
Drop the line in the error path of kvm_arch_vcpu_create().
Fixes: ff030fdf55 ("KVM: PPC: Move kvm_vcpu_init() invocation to common code")
Signed-off-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/158455341029.178873.15248663726399374882.stgit@bahia.lan
Currently you can enable PPC_KUAP_DEBUG when PPC_KUAP is disabled,
even though the former has not effect without the latter.
Fix it so that PPC_KUAP_DEBUG can only be enabled when PPC_KUAP is
enabled, not when the platform could support KUAP (PPC_HAVE_KUAP).
Fixes: 890274c2dc ("powerpc/64s: Implement KUAP for Radix MMU")
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200301111738.22497-1-mpe@ellerman.id.au
Simplify gen_btf logic to make it work with llvm-objcopy. The existing
'file format' and 'architecture' parsing logic is brittle and does not
work with llvm-objcopy/llvm-objdump.
'file format' output of llvm-objdump>=11 will match GNU objdump, but
'architecture' (bfdarch) may not.
.BTF in .tmp_vmlinux.btf is non-SHF_ALLOC. Add the SHF_ALLOC flag
because it is part of vmlinux image used for introspection. C code
can reference the section via linker script defined __start_BTF and
__stop_BTF. This fixes a small problem that previous .BTF had the
SHF_WRITE flag (objcopy -I binary -O elf* synthesized .data).
Additionally, `objcopy -I binary` synthesized symbols
_binary__btf_vmlinux_bin_start and _binary__btf_vmlinux_bin_stop (not
used elsewhere) are replaced with more commonplace __start_BTF and
__stop_BTF.
Add 2>/dev/null because GNU objcopy (but not llvm-objcopy) warns
"empty loadable segment detected at vaddr=0xffffffff81000000, is this intentional?"
We use a dd command to change the e_type field in the ELF header from
ET_EXEC to ET_REL so that lld will accept .btf.vmlinux.bin.o. Accepting
ET_EXEC as an input file is an extremely rare GNU ld feature that lld
does not intend to support, because this is error-prone.
The output section description .BTF in include/asm-generic/vmlinux.lds.h
avoids potential subtle orphan section placement issues and suppresses
--orphan-handling=warn warnings.
Fixes: df786c9b94 ("bpf: Force .BTF section start to zero when dumping from vmlinux")
Fixes: cb0cc635c7 ("powerpc: Include .BTF section")
Reported-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Fangrui Song <maskray@google.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Tested-by: Stanislav Fomichev <sdf@google.com>
Tested-by: Andrii Nakryiko <andriin@fb.com>
Reviewed-by: Stanislav Fomichev <sdf@google.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Acked-by: Andrii Nakryiko <andriin@fb.com>
Acked-by: Michael Ellerman <mpe@ellerman.id.au> (powerpc)
Link: https://github.com/ClangBuiltLinux/linux/issues/871
Link: https://lore.kernel.org/bpf/20200318222746.173648-1-maskray@google.com
These are only used by HV KVM and BookE, and in both cases they are
nops.
Signed-off-by: Greg Kurz <groug@kaod.org>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
This is only relevant to PR KVM. Make it obvious by moving the
function declaration to the Book3s header and rename it with
a _pr suffix.
Signed-off-by: Greg Kurz <groug@kaod.org>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
With PR KVM, shutting down a VM causes the host kernel to crash:
[ 314.219284] BUG: Unable to handle kernel data access on read at 0xc00800000176c638
[ 314.219299] Faulting instruction address: 0xc008000000d4ddb0
cpu 0x0: Vector: 300 (Data Access) at [c00000036da077a0]
pc: c008000000d4ddb0: kvmppc_mmu_pte_flush_all+0x68/0xd0 [kvm_pr]
lr: c008000000d4dd94: kvmppc_mmu_pte_flush_all+0x4c/0xd0 [kvm_pr]
sp: c00000036da07a30
msr: 900000010280b033
dar: c00800000176c638
dsisr: 40000000
current = 0xc00000036d4c0000
paca = 0xc000000001a00000 irqmask: 0x03 irq_happened: 0x01
pid = 1992, comm = qemu-system-ppc
Linux version 5.6.0-master-gku+ (greg@palmb) (gcc version 7.5.0 (Ubuntu 7.5.0-3ubuntu1~18.04)) #17 SMP Wed Mar 18 13:49:29 CET 2020
enter ? for help
[c00000036da07ab0] c008000000d4fbe0 kvmppc_mmu_destroy_pr+0x28/0x60 [kvm_pr]
[c00000036da07ae0] c0080000009eab8c kvmppc_mmu_destroy+0x34/0x50 [kvm]
[c00000036da07b00] c0080000009e50c0 kvm_arch_vcpu_destroy+0x108/0x140 [kvm]
[c00000036da07b30] c0080000009d1b50 kvm_vcpu_destroy+0x28/0x80 [kvm]
[c00000036da07b60] c0080000009e4434 kvm_arch_destroy_vm+0xbc/0x190 [kvm]
[c00000036da07ba0] c0080000009d9c2c kvm_put_kvm+0x1d4/0x3f0 [kvm]
[c00000036da07c00] c0080000009da760 kvm_vm_release+0x38/0x60 [kvm]
[c00000036da07c30] c000000000420be0 __fput+0xe0/0x310
[c00000036da07c90] c0000000001747a0 task_work_run+0x150/0x1c0
[c00000036da07cf0] c00000000014896c do_exit+0x44c/0xd00
[c00000036da07dc0] c0000000001492f4 do_group_exit+0x64/0xd0
[c00000036da07e00] c000000000149384 sys_exit_group+0x24/0x30
[c00000036da07e20] c00000000000b9d0 system_call+0x5c/0x68
This is caused by a use-after-free in kvmppc_mmu_pte_flush_all()
which dereferences vcpu->arch.book3s which was previously freed by
kvmppc_core_vcpu_free_pr(). This happens because kvmppc_mmu_destroy()
is called after kvmppc_core_vcpu_free() since commit ff030fdf55
("KVM: PPC: Move kvm_vcpu_init() invocation to common code").
The kvmppc_mmu_destroy() helper calls one of the following depending
on the KVM backend:
- kvmppc_mmu_destroy_hv() which does nothing (Book3s HV)
- kvmppc_mmu_destroy_pr() which undoes the effects of
kvmppc_mmu_init() (Book3s PR 32-bit)
- kvmppc_mmu_destroy_pr() which undoes the effects of
kvmppc_mmu_init() (Book3s PR 64-bit)
- kvmppc_mmu_destroy_e500() which does nothing (BookE e500/e500mc)
It turns out that this is only relevant to PR KVM actually. And both
32 and 64 backends need vcpu->arch.book3s to be valid when calling
kvmppc_mmu_destroy_pr(). So instead of calling kvmppc_mmu_destroy()
from kvm_arch_vcpu_destroy(), call kvmppc_mmu_destroy_pr() at the
beginning of kvmppc_core_vcpu_free_pr(). This is consistent with
kvmppc_mmu_init() being the last call in kvmppc_core_vcpu_create_pr().
For the same reason, if kvmppc_core_vcpu_create_pr() returns an
error then this means that kvmppc_mmu_init() was either not called
or failed, in which case kvmppc_mmu_destroy() should not be called.
Drop the line in the error path of kvm_arch_vcpu_create().
Fixes: ff030fdf55 ("KVM: PPC: Move kvm_vcpu_init() invocation to common code")
Signed-off-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
The h_cede_tm kvm-unit-test currently fails when run inside an L1 guest
via the guest/nested hypervisor.
./run-tests.sh -v
...
TESTNAME=h_cede_tm TIMEOUT=90s ACCEL= ./powerpc/run powerpc/tm.elf -smp 2,threads=2 -machine cap-htm=on -append "h_cede_tm"
FAIL h_cede_tm (2 tests, 1 unexpected failures)
While the test relates to transactional memory instructions, the actual
failure is due to the return code of the H_CEDE hypercall, which is
reported as 224 instead of 0. This happens even when no TM instructions
are issued.
224 is the value placed in r3 to execute a hypercall for H_CEDE, and r3
is where the caller expects the return code to be placed upon return.
In the case of guest running under a nested hypervisor, issuing H_CEDE
causes a return from H_ENTER_NESTED. In this case H_CEDE is
specially-handled immediately rather than later in
kvmppc_pseries_do_hcall() as with most other hcalls, but we forget to
set the return code for the caller, hence why kvm-unit-test sees the
224 return code and reports an error.
Guest kernels generally don't check the return value of H_CEDE, so
that likely explains why this hasn't caused issues outside of
kvm-unit-tests so far.
Fix this by setting r3 to 0 after we finish processing the H_CEDE.
RHBZ: 1778556
Fixes: 4bad77799f ("KVM: PPC: Book3S HV: Handle hypercalls correctly when nested")
Cc: linuxppc-dev@ozlabs.org
Cc: David Gibson <david@gibson.dropbear.id.au>
Cc: Paul Mackerras <paulus@ozlabs.org>
Signed-off-by: Michael Roth <mdroth@linux.vnet.ibm.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
On P9 DD2.2 due to a CPU defect some TM instructions need to be emulated by
KVM. This is handled at first by the hardware raising a softpatch interrupt
when certain TM instructions that need KVM assistance are executed in the
guest. Althought some TM instructions per Power ISA are invalid forms they
can raise a softpatch interrupt too. For instance, 'tresume.' instruction
as defined in the ISA must have bit 31 set (1), but an instruction that
matches 'tresume.' PO and XO opcode fields but has bit 31 not set (0), like
0x7cfe9ddc, also raises a softpatch interrupt. Similarly for 'treclaim.'
and 'trechkpt.' instructions with bit 31 = 0, i.e. 0x7c00075c and
0x7c0007dc, respectively. Hence, if a code like the following is executed
in the guest it will raise a softpatch interrupt just like a 'tresume.'
when the TM facility is enabled ('tabort. 0' in the example is used only
to enable the TM facility):
int main() { asm("tabort. 0; .long 0x7cfe9ddc;"); }
Currently in such a case KVM throws a complete trace like:
[345523.705984] WARNING: CPU: 24 PID: 64413 at arch/powerpc/kvm/book3s_hv_tm.c:211 kvmhv_p9_tm_emulation+0x68/0x620 [kvm_hv]
[345523.705985] Modules linked in: kvm_hv(E) xt_conntrack ipt_REJECT nf_reject_ipv4 xt_tcpudp ip6table_mangle ip6table_nat
iptable_mangle iptable_nat nf_nat nf_conntrack nf_defrag_ipv6 nf_defrag_ipv4 ebtable_filter ebtables ip6table_filter
ip6_tables iptable_filter bridge stp llc sch_fq_codel ipmi_powernv at24 vmx_crypto ipmi_devintf ipmi_msghandler
ibmpowernv uio_pdrv_genirq kvm opal_prd uio leds_powernv ib_iser rdma_cm iw_cm ib_cm ib_core iscsi_tcp libiscsi_tcp
libiscsi scsi_transport_iscsi ip_tables x_tables autofs4 btrfs blake2b_generic zstd_compress raid10 raid456
async_raid6_recov async_memcpy async_pq async_xor async_tx libcrc32c xor raid6_pq raid1 raid0 multipath linear tg3
crct10dif_vpmsum crc32c_vpmsum ipr [last unloaded: kvm_hv]
[345523.706030] CPU: 24 PID: 64413 Comm: CPU 0/KVM Tainted: G W E 5.5.0+ #1
[345523.706031] NIP: c0080000072cb9c0 LR: c0080000072b5e80 CTR: c0080000085c7850
[345523.706034] REGS: c000000399467680 TRAP: 0700 Tainted: G W E (5.5.0+)
[345523.706034] MSR: 900000010282b033 <SF,HV,VEC,VSX,EE,FP,ME,IR,DR,RI,LE,TM[E]> CR: 24022428 XER: 00000000
[345523.706042] CFAR: c0080000072b5e7c IRQMASK: 0
GPR00: c0080000072b5e80 c000000399467910 c0080000072db500 c000000375ccc720
GPR04: c000000375ccc720 00000003fbec0000 0000a10395dda5a6 0000000000000000
GPR08: 000000007cfe9ddc 7cfe9ddc000005dc 7cfe9ddc7c0005dc c0080000072cd530
GPR12: c0080000085c7850 c0000003fffeb800 0000000000000001 00007dfb737f0000
GPR16: c0002001edcca558 0000000000000000 0000000000000000 0000000000000001
GPR20: c000000001b21258 c0002001edcca558 0000000000000018 0000000000000000
GPR24: 0000000001000000 ffffffffffffffff 0000000000000001 0000000000001500
GPR28: c0002001edcc4278 c00000037dd80000 800000050280f033 c000000375ccc720
[345523.706062] NIP [c0080000072cb9c0] kvmhv_p9_tm_emulation+0x68/0x620 [kvm_hv]
[345523.706065] LR [c0080000072b5e80] kvmppc_handle_exit_hv.isra.53+0x3e8/0x798 [kvm_hv]
[345523.706066] Call Trace:
[345523.706069] [c000000399467910] [c000000399467940] 0xc000000399467940 (unreliable)
[345523.706071] [c000000399467950] [c000000399467980] 0xc000000399467980
[345523.706075] [c0000003994679f0] [c0080000072bd1c4] kvmhv_run_single_vcpu+0xa1c/0xb80 [kvm_hv]
[345523.706079] [c000000399467ac0] [c0080000072bd8e0] kvmppc_vcpu_run_hv+0x5b8/0xb00 [kvm_hv]
[345523.706087] [c000000399467b90] [c0080000085c93cc] kvmppc_vcpu_run+0x34/0x48 [kvm]
[345523.706095] [c000000399467bb0] [c0080000085c582c] kvm_arch_vcpu_ioctl_run+0x244/0x420 [kvm]
[345523.706101] [c000000399467c40] [c0080000085b7498] kvm_vcpu_ioctl+0x3d0/0x7b0 [kvm]
[345523.706105] [c000000399467db0] [c0000000004adf9c] ksys_ioctl+0x13c/0x170
[345523.706107] [c000000399467e00] [c0000000004adff8] sys_ioctl+0x28/0x80
[345523.706111] [c000000399467e20] [c00000000000b278] system_call+0x5c/0x68
[345523.706112] Instruction dump:
[345523.706114] 419e0390 7f8a4840 409d0048 6d497c00 2f89075d 419e021c 6d497c00 2f8907dd
[345523.706119] 419e01c0 6d497c00 2f8905dd 419e00a4 <0fe00000> 38210040 38600000 ebc1fff0
and then treats the executed instruction as a 'nop'.
However the POWER9 User's Manual, in section "4.6.10 Book II Invalid
Forms", informs that for TM instructions bit 31 is in fact ignored, thus
for the TM-related invalid forms ignoring bit 31 and handling them like the
valid forms is an acceptable way to handle them. POWER8 behaves the same
way too.
This commit changes the handling of the cases here described by treating
the TM-related invalid forms that can generate a softpatch interrupt
just like their valid forms (w/ bit 31 = 1) instead of as a 'nop' and by
gently reporting any other unrecognized case to the host and treating it as
illegal instruction instead of throwing a trace and treating it as a 'nop'.
Signed-off-by: Gustavo Romero <gromero@linux.ibm.com>
Reviewed-by: Segher Boessenkool <segher@kernel.crashing.org>
Acked-By: Michael Neuling <mikey@neuling.org>
Reviewed-by: Leonardo Bras <leonardo@linux.ibm.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
In kvmppc_unmap_free_pte() in book3s_64_mmu_radix.c, we use the
non-constant value PTE_INDEX_SIZE to clear a PTE page.
We can instead use the constant RADIX_PTE_INDEX_SIZE, because we know
this code will only be running when the Radix MMU is active.
Note that we already use RADIX_PTE_INDEX_SIZE for the allocation of
kvm_pte_cache.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Reviewed-by: Leonardo Bras <leonardo@linux.ibm.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
This makes the same changes in the page fault handler for HPT guests
that commits 31c8b0d069 ("KVM: PPC: Book3S HV: Use __gfn_to_pfn_memslot()
in page fault handler", 2018-03-01), 71d29f43b6 ("KVM: PPC: Book3S HV:
Don't use compound_order to determine host mapping size", 2018-09-11)
and 6579804c43 ("KVM: PPC: Book3S HV: Avoid crash from THP collapse
during radix page fault", 2018-10-04) made for the page fault handler
for radix guests.
In summary, where we used to call get_user_pages_fast() and then do
special handling for VM_PFNMAP vmas, we now call __get_user_pages_fast()
and then __gfn_to_pfn_memslot() if that fails, followed by reading the
Linux PTE to get the host PFN, host page size and mapping attributes.
This also brings in the change from SetPageDirty() to set_page_dirty_lock()
which was done for the radix page fault handler in commit c3856aeb29
("KVM: PPC: Book3S HV: Fix handling of large pages in radix page fault
handler", 2018-02-23).
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
The NDD_ALIASING flag is used to indicate where pmem capacity might
alias with blk capacity and require labeling. It is also used to
indicate whether the DIMM supports labeling. Separate this latter
capability into its own flag so that the NDD_ALIASING flag is scoped to
true aliased configurations.
To my knowledge aliased configurations only exist in the ACPI spec,
there are no known platforms that ship this support in production.
This clarity allows namespace-capacity alignment constraints around
interleave-ways to be relaxed.
Cc: Vishal Verma <vishal.l.verma@intel.com>
Cc: Oliver O'Halloran <oohall@gmail.com>
Reviewed-by: Jeff Moyer <jmoyer@redhat.com>
Reviewed-by: Aneesh Kumar K.V <aneesh.kumar@linux.ibm.com>
Link: https://lore.kernel.org/r/158041477856.3889308.4212605617834097674.stgit@dwillia2-desk3.amr.corp.intel.com
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
We should be checking that the instruction was stepped *and* that the
target register has the right value.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Reviewed-by: Ravi Bangoria <ravi.bangoria@linux.ibm.com>
[mpe: Write change log]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200226055302.1577954-1-npiggin@gmail.com
When building with ppc64_defconfig, the compiler reports
that these 2 variables are not used:
warning: unused variable 'core99_l2_cache' [-Wunused-variable]
warning: unused variable 'core99_l3_cache' [-Wunused-variable]
They are only used when CONFIG_PPC64 is not defined. Move
them into a section which does the same macro check.
Reported-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Ilie Halip <ilie.halip@gmail.com>
[mpe: Move them into core99_init_caches() which is their only user]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20190920153951.25762-1-ilie.halip@gmail.com
In the current implementation, the call to loadcam_multi() is wrapped
between switch_to_as1() and restore_to_as0() calls so, when it tries
to create its own temporary AS=1 TLB1 entry, it ends up duplicating
the existing one created by switch_to_as1(). Add a check to skip
creating the temporary entry if already running in AS=1.
Fixes: d9e1831a42 ("powerpc/85xx: Load all early TLB entries at once")
Cc: stable@vger.kernel.org # v4.4+
Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Acked-by: Scott Wood <oss@buserror.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200123111914.2565-1-laurentiu.tudor@nxp.com
Remove includes of asm/kvm_host.h from files that already include
linux/kvm_host.h to make it more obvious that there is no ordering issue
between the two headers. linux/kvm_host.h includes asm/kvm_host.h to
pick up architecture specific settings, and this will never change, i.e.
including asm/kvm_host.h after linux/kvm_host.h may seem problematic,
but in practice is simply redundant.
Signed-off-by: Peter Xu <peterx@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Refactor memslot handling to treat the number of used slots as the de
facto size of the memslot array, e.g. return NULL from id_to_memslot()
when an invalid index is provided instead of relying on npages==0 to
detect an invalid memslot. Rework the sorting and walking of memslots
in advance of dynamically sizing memslots to aid bisection and debug,
e.g. with luck, a bug in the refactoring will bisect here and/or hit a
WARN instead of randomly corrupting memory.
Alternatively, a global null/invalid memslot could be returned, i.e. so
callers of id_to_memslot() don't have to explicitly check for a NULL
memslot, but that approach runs the risk of introducing difficult-to-
debug issues, e.g. if the global null slot is modified. Constifying
the return from id_to_memslot() to combat such issues is possible, but
would require a massive refactoring of arch specific code and would
still be susceptible to casting shenanigans.
Add function comments to update_memslots() and search_memslots() to
explicitly (and loudly) state how memslots are sorted.
Opportunistically stuff @hva with a non-canonical value when deleting a
private memslot on x86 to detect bogus usage of the freed slot.
No functional change intended.
Tested-by: Christoffer Dall <christoffer.dall@arm.com>
Tested-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Rework kvm_get_dirty_log() so that it "returns" the associated memslot
on success. A future patch will rework memslot handling such that
id_to_memslot() can return NULL, returning the memslot makes it more
obvious that the validity of the memslot has been verified, i.e.
precludes the need to add validity checks in the arch code that are
technically unnecessary.
To maintain ordering in s390, move the call to kvm_arch_sync_dirty_log()
from s390's kvm_vm_ioctl_get_dirty_log() to the new kvm_get_dirty_log().
This is a nop for PPC, the only other arch that doesn't select
KVM_GENERIC_DIRTYLOG_READ_PROTECT, as its sync_dirty_log() is empty.
Ideally, moving the sync_dirty_log() call would be done in a separate
patch, but it can't be done in a follow-on patch because that would
temporarily break s390's ordering. Making the move in a preparatory
patch would be functionally correct, but would create an odd scenario
where the moved sync_dirty_log() would operate on a "different" memslot
due to consuming the result of a different id_to_memslot(). The
memslot couldn't actually be different as slots_lock is held, but the
code is confusing enough as it is, i.e. moving sync_dirty_log() in this
patch is the lesser of all evils.
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Move the implementations of KVM_GET_DIRTY_LOG and KVM_CLEAR_DIRTY_LOG
for CONFIG_KVM_GENERIC_DIRTYLOG_READ_PROTECT into common KVM code.
The arch specific implemenations are extremely similar, differing
only in whether the dirty log needs to be sync'd from hardware (x86)
and how the TLBs are flushed. Add new arch hooks to handle sync
and TLB flush; the sync will also be used for non-generic dirty log
support in a future patch (s390).
The ulterior motive for providing a common implementation is to
eliminate the dependency between arch and common code with respect to
the memslot referenced by the dirty log, i.e. to make it obvious in the
code that the validity of the memslot is guaranteed, as a future patch
will rework memslot handling such that id_to_memslot() can return NULL.
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Now that all callers of kvm_free_memslot() pass NULL for @dont, remove
the param from the top-level routine and all arch's implementations.
No functional change intended.
Tested-by: Christoffer Dall <christoffer.dall@arm.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Drop the "const" attribute from @old in kvm_arch_commit_memory_region()
to allow arch specific code to free arch specific resources in the old
memslot without having to cast away the attribute. Freeing resources in
kvm_arch_commit_memory_region() paves the way for simplifying
kvm_free_memslot() by eliminating the last usage of its @dont param.
Reviewed-by: Peter Xu <peterx@redhat.com>
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Remove kvm_arch_create_memslot() now that all arch implementations are
effectively nops. Removing kvm_arch_create_memslot() eliminates the
possibility for arch specific code to allocate memory prior to setting
a memslot, which sets the stage for simplifying kvm_free_memslot().
Cc: Janosch Frank <frankja@linux.ibm.com>
Acked-by: Christian Borntraeger <borntraeger@de.ibm.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Allocate the rmap array during kvm_arch_prepare_memory_region() to pave
the way for removing kvm_arch_create_memslot() altogether. Moving PPC's
memory allocation only changes the order of kernel memory allocations
between PPC and common KVM code.
No functional change intended.
Acked-by: Paul Mackerras <paulus@ozlabs.org>
Reviewed-by: Peter Xu <peterx@redhat.com>
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The original 2005 patch that introduced the powerpc vdso, pre-git
("ppc64: Implement a vDSO and use it for signal trampoline") notes that:
... symbols exposed by the vDSO aren't "normal" function symbols, apps
can't be expected to link against them directly, the vDSO's are both
seen as if they were linked at 0 and the symbols just contain offsets
to the various functions. This is done on purpose to avoid a
relocation step (ppc64 functions normally have descriptors with abs
addresses in them). When glibc uses those functions, it's expected to
use it's own trampolines that know how to reach them.
Despite that explanation, there remains dead #ifdef
VDS64_HAS_DESCRIPTORS code-blocks that provide alternate function
definitions that setup function descriptors.
Since VDS64_HAS_DESCRIPTORS has been unused for all these years, we
might as well finally remove it from the codebase.
Signed-off-by: Joe Lawrence <joe.lawrence@redhat.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200224211848.26087-1-joe.lawrence@redhat.com
Commit 2efc7c085f ("powerpc/32: drop get_pteptr()"),
replaced get_pteptr() by virt_to_kpte(). But virt_to_kpte() lacks a
NULL pmd check and returns an invalid non NULL pointer when there
is no page table.
Reported-by: Nick Desaulniers <ndesaulniers@google.com>
Fixes: 2efc7c085f ("powerpc/32: drop get_pteptr()")
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Tested-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/b1177cdfc6af74a3e277bba5d9e708c4b3315ebe.1583575707.git.christophe.leroy@c-s.fr
With CONFIG_KASAN_VMALLOC, new page tables are created at the time
shadow memory for vmalloc area is unmapped. If some parts of the
page table still have entries to the zero page shadow memory, the
entries are wrongly marked RW.
With CONFIG_KASAN_VMALLOC, almost the entire kernel address space
is managed by KASAN. To make it simple, just create KASAN page tables
for the entire kernel space at kasan_init(). That doesn't use much
more space, and that's anyway already done for hash platforms.
Fixes: 3d4247fcc9 ("powerpc/32: Add support of KASAN_VMALLOC")
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/ef5248fc1f496c6b0dfdb59380f24968f25f75c5.1583513368.git.christophe.leroy@c-s.fr
Every time a new architecture defines the IMA architecture specific
functions - arch_ima_get_secureboot() and arch_ima_get_policy(), the IMA
include file needs to be updated. To avoid this "noise", this patch
defines a new IMA Kconfig IMA_SECURE_AND_OR_TRUSTED_BOOT option, allowing
the different architectures to select it.
Suggested-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Nayna Jain <nayna@linux.ibm.com>
Acked-by: Ard Biesheuvel <ardb@kernel.org>
Acked-by: Philipp Rudo <prudo@linux.ibm.com> (s390)
Acked-by: Michael Ellerman <mpe@ellerman.id.au> (powerpc)
Signed-off-by: Mimi Zohar <zohar@linux.ibm.com>
Stefan reported a strange kernel fault which turned out to be due to a
missing KUAP disable in flush_coherent_icache() called from
flush_icache_range().
The fault looks like:
Kernel attempted to access user page (7fffc30d9c00) - exploit attempt? (uid: 1009)
BUG: Unable to handle kernel data access on read at 0x7fffc30d9c00
Faulting instruction address: 0xc00000000007232c
Oops: Kernel access of bad area, sig: 11 [#1]
LE PAGE_SIZE=64K MMU=Radix SMP NR_CPUS=2048 NUMA PowerNV
CPU: 35 PID: 5886 Comm: sigtramp Not tainted 5.6.0-rc2-gcc-8.2.0-00003-gfc37a1632d40 #79
NIP: c00000000007232c LR: c00000000003b7fc CTR: 0000000000000000
REGS: c000001e11093940 TRAP: 0300 Not tainted (5.6.0-rc2-gcc-8.2.0-00003-gfc37a1632d40)
MSR: 900000000280b033 <SF,HV,VEC,VSX,EE,FP,ME,IR,DR,RI,LE> CR: 28000884 XER: 00000000
CFAR: c0000000000722fc DAR: 00007fffc30d9c00 DSISR: 08000000 IRQMASK: 0
GPR00: c00000000003b7fc c000001e11093bd0 c0000000023ac200 00007fffc30d9c00
GPR04: 00007fffc30d9c18 0000000000000000 c000001e11093bd4 0000000000000000
GPR08: 0000000000000000 0000000000000001 0000000000000000 c000001e1104ed80
GPR12: 0000000000000000 c000001fff6ab380 c0000000016be2d0 4000000000000000
GPR16: c000000000000000 bfffffffffffffff 0000000000000000 0000000000000000
GPR20: 00007fffc30d9c00 00007fffc30d8f58 00007fffc30d9c18 00007fffc30d9c20
GPR24: 00007fffc30d9c18 0000000000000000 c000001e11093d90 c000001e1104ed80
GPR28: c000001e11093e90 0000000000000000 c0000000023d9d18 00007fffc30d9c00
NIP flush_icache_range+0x5c/0x80
LR handle_rt_signal64+0x95c/0xc2c
Call Trace:
0xc000001e11093d90 (unreliable)
handle_rt_signal64+0x93c/0xc2c
do_notify_resume+0x310/0x430
ret_from_except_lite+0x70/0x74
Instruction dump:
409e002c 7c0802a6 3c62ff31 3863f6a0 f8010080 48195fed 60000000 48fe4c8d
60000000 e8010080 7c0803a6 7c0004ac <7c00ffac> 7c0004ac 4c00012c 38210070
This path through handle_rt_signal64() to setup_trampoline() and
flush_icache_range() is only triggered by 64-bit processes that have
unmapped their VDSO, which is rare.
flush_icache_range() takes a range of addresses to flush. In
flush_coherent_icache() we implement an optimisation for CPUs where we
know we don't actually have to flush the whole range, we just need to
do a single icbi.
However we still execute the icbi on the user address of the start of
the range we're flushing. On CPUs that also implement KUAP (Power9)
that leads to the spurious fault above.
We should be able to pass any address, including a kernel address, to
the icbi on these CPUs, which would avoid any interaction with KUAP.
But I don't want to make that change in a bug fix, just in case it
surfaces some strange behaviour on some CPU.
So for now just disable KUAP around the icbi. Note the icbi is treated
as a load, so we allow read access, not write as you'd expect.
Fixes: 890274c2dc ("powerpc/64s: Implement KUAP for Radix MMU")
Cc: stable@vger.kernel.org # v5.2+
Reported-by: Stefan Berger <stefanb@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200303235708.26004-1-mpe@ellerman.id.au
With commit ("powerpc/numa: Early request for home node associativity"),
commit 2ea6263068 ("powerpc/topology: Get topology for shared
processors at boot") which was requesting home node associativity
becomes redundant.
Hence remove the late request for home node associativity.
Signed-off-by: Srikar Dronamraju <srikar@linux.vnet.ibm.com>
Reported-by: Abdul Haleem <abdhalee@linux.vnet.ibm.com>
Reviewed-by: Nathan Lynch <nathanl@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200129135301.24739-6-srikar@linux.vnet.ibm.com
Currently the kernel detects if its running on a shared lpar platform
and requests home node associativity before the scheduler sched_domains
are setup. However between the time NUMA setup is initialized and the
request for home node associativity, workqueue initializes its per node
cpumask. The per node workqueue possible cpumask may turn invalid
after home node associativity resulting in weird situations like
workqueue possible cpumask being a subset of workqueue online cpumask.
This can be fixed by requesting home node associativity earlier just
before NUMA setup. However at the NUMA setup time, kernel may not be in
a position to detect if its running on a shared lpar platform. So
request for home node associativity and if the request fails, fallback
on the device tree property.
Signed-off-by: Srikar Dronamraju <srikar@linux.vnet.ibm.com>
Reported-by: Abdul Haleem <abdhalee@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200129135301.24739-5-srikar@linux.vnet.ibm.com
All the sibling threads of a core have to be part of the same node.
To ensure that all the sibling threads map to the same node, always
lookup/update the cpu-to-node map of the first thread in the core.
Signed-off-by: Srikar Dronamraju <srikar@linux.vnet.ibm.com>
Reported-by: Abdul Haleem <abdhalee@linux.vnet.ibm.com>
Reviewed-by: Nathan Lynch <nathanl@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200129135301.24739-4-srikar@linux.vnet.ibm.com
Currently code handles H_FUNCTION, H_SUCCESS, H_HARDWARE return codes.
However hcall_vphn can return other return codes. Now it also handles
H_PARAMETER return code. Also the rest return codes are handled under the
default case.
Signed-off-by: Srikar Dronamraju <srikar@linux.vnet.ibm.com>
Reported-by: Abdul Haleem <abdhalee@linux.vnet.ibm.com>
Reviewed-by: Nathan Lynch <nathanl@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200129135301.24739-3-srikar@linux.vnet.ibm.com
There is no value in unpacking associativity, if
H_HOME_NODE_ASSOCIATIVITY hcall has returned an error.
Signed-off-by: Srikar Dronamraju <srikar@linux.vnet.ibm.com>
Reported-by: Abdul Haleem <abdhalee@linux.vnet.ibm.com>
Reviewed-by: Nathan Lynch <nathanl@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200129135301.24739-2-srikar@linux.vnet.ibm.com
package_id is to match cores that are part of the same chip. On
PowerNV machines, package_id defaults to chip_id. However ibm,chip_id
property is not present in device-tree of PowerVM LPARs. Hence lscpu
output shows one core per socket and multiple cores.
To overcome this, use nid as the package_id on PowerVM LPARs.
Before the patch:
Architecture: ppc64le
Byte Order: Little Endian
CPU(s): 128
On-line CPU(s) list: 0-127
Thread(s) per core: 8
Core(s) per socket: 1 <----------------------
Socket(s): 16 <----------------------
NUMA node(s): 2
Model: 2.2 (pvr 004e 0202)
Model name: POWER9 (architected), altivec supported
Hypervisor vendor: pHyp
Virtualization type: para
L1d cache: 32K
L1i cache: 32K
L2 cache: 512K
L3 cache: 10240K
NUMA node0 CPU(s): 0-63
NUMA node1 CPU(s): 64-127
#
# cat /sys/devices/system/cpu/cpu0/topology/physical_package_id
-1
After the patch:
Architecture: ppc64le
Byte Order: Little Endian
CPU(s): 128
On-line CPU(s) list: 0-127
Thread(s) per core: 8 <---------------------
Core(s) per socket: 8 <---------------------
Socket(s): 2
NUMA node(s): 2
Model: 2.2 (pvr 004e 0202)
Model name: POWER9 (architected), altivec supported
Hypervisor vendor: pHyp
Virtualization type: para
L1d cache: 32K
L1i cache: 32K
L2 cache: 512K
L3 cache: 10240K
NUMA node0 CPU(s): 0-63
NUMA node1 CPU(s): 64-127
#
# cat /sys/devices/system/cpu/cpu0/topology/physical_package_id
0
Now lscpu output is more in line with the system configuration.
Signed-off-by: Srikar Dronamraju <srikar@linux.vnet.ibm.com>
[mpe: Use pkg_id instead of ppid, tweak change log and comment]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200129135121.24617-1-srikar@linux.vnet.ibm.com
Until commit 7306e83ccf ("powerpc: Don't use CURRENT_THREAD_INFO to
find the stack"), the current stack base address was obtained by
calling current_thread_info(). That inline function was simply masking
out the value of r1.
In that commit, it was changed to using current_stack_pointer() (since
renamed current_stack_frame()), which is a heavier function as it is
an outline assembly function which cannot be inlined and which reads
the content of the stack at 0(r1).
Convert to using current_stack_pointer for geting r1 and masking out
its value to obtain the base address of the stack pointer as before.
Fixes: 7306e83ccf ("powerpc: Don't use CURRENT_THREAD_INFO to find the stack")
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200220115141.2707-5-mpe@ellerman.id.au
Instead of #ifdef, use IS_ENABLED(CONFIG_DEBUG_STACKOVERFLOW).
This enable GCC to check for code validity even when the option
is not selected.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200220115141.2707-4-mpe@ellerman.id.au
The purpose of check_stack_overflow() is to verify that the stack has
not overflowed.
To really know whether the stack pointer is still within boundaries,
the check must be done directly on the value of r1.
So use current_stack_pointer, which returns the current value of r1,
rather than current_stack_frame() which causes a frame to be created
and then returns that value.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200220115141.2707-3-mpe@ellerman.id.au
current_stack_frame() doesn't return the stack pointer, but the
caller's stack frame. See commit bfe9a2cfe9 ("powerpc: Reimplement
__get_SP() as a function not a define") and commit
acf620ecf5 ("powerpc: Rename __get_SP() to current_stack_pointer()")
for details.
In some cases this is overkill or incorrect, as it doesn't return the
current value of r1.
So add a current_stack_pointer register global to get the value of r1
directly.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
[mpe: Split out of other patch, tweak change log]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200220115141.2707-2-mpe@ellerman.id.au
current_stack_pointer(), which was called __get_SP(), used to just
return the value in r1.
But that caused problems in some cases, so it was turned into a
function in commit bfe9a2cfe9 ("powerpc: Reimplement __get_SP() as a
function not a define").
Because it's a function in a separate compilation unit to all its
callers, it has the effect of causing a stack frame to be created, and
then returns the address of that frame. This is good in some cases
like those described in the above commit, but in other cases it's
overkill, we just need to know what stack page we're on.
On some other arches current_stack_pointer is just a register global
giving the stack pointer, and we'd like to do that too. So rename our
current_stack_pointer() to current_stack_frame() to make that
possible.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Reviewed-by: Christophe Leroy <christophe.leroy@c-s.fr>
Link: https://lore.kernel.org/r/20200220115141.2707-1-mpe@ellerman.id.au
Many of the performance monitoring unit (PMU) SPRs are
exposed in the sysfs. This may not be a desirable since
"perf" API is the primary interface to program PMU and
collect counter data in the system. But that said, we
cant remove these sysfs files since we dont whether
anyone/anything is using them.
So the patch adds a new CONFIG option 'CONFIG_PMU_SYSFS'
(user selectable) to be used in sysfs file creation for
PMU SPRs. New option by default is disabled, but can be
enabled if user needs it.
Tested this patch behaviour in powernv and pseries machines.
Patch is also tested for pmac32_defconfig.
Signed-off-by: Kajol Jain <kjain@linux.ibm.com>
Tested-by: Nageswara R Sastry <nasastry@in.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200214080606.26872-2-kjain@linux.ibm.com
An attempt to refactor the current sysfs.c file.
To start with a big chuck of macro #defines and dscr
functions are moved to start of the file. Secondly,
HAS_ #define macros are cleanup based on CONFIG_ options
Finally new HAS_ macro added:
1. HAS_PPC_PA6T (for PA6T) to separate out non-PMU SPRs.
2. HAS_PPC_PMC56 to separate out PMC SPR's from HAS_PPC_PMC_CLASSIC
which come under CONFIG_PPC64.
Signed-off-by: Madhavan Srinivasan <maddy@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200214080606.26872-1-kjain@linux.ibm.com
Add a way to manually invoke a fast-reboot rather than setting the NVRAM
flag. The idea is to allow userspace to invoke a fast-reboot using the
optional string argument to the reboot() system call, or using the xmon
zr command so we don't need to leave around a persistent changes on
a system to use the feature.
Signed-off-by: Oliver O'Halloran <oohall@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200217024833.30580-2-oohall@gmail.com
Treat an empty reboot cmd string the same as a NULL string. This squashes a
spurious unsupported reboot message that sometimes gets out when using
xmon.
Signed-off-by: Oliver O'Halloran <oohall@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200217024833.30580-1-oohall@gmail.com
Some of our phony targets are not marked as such. This can lead to
confusing errors, eg:
$ make clean
$ touch install
$ make install
make: 'install' is up to date.
$
Fix it by adding them to the PHONY variable which is marked phony in
the top-level Makefile, or in scripts/Makefile.build for the boot
Makefile.
Suggested-by: Masahiro Yamada <masahiroy@kernel.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Reviewed-by: Masahiro Yamada <masahiroy@kernel.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200219000434.15872-1-mpe@ellerman.id.au
On PPC32, pte_offset_map() does a kmap_atomic() in order to support
page tables allocated in high memory, just like ARM and x86/32.
But since at least 2008 and commit 8054a3428f ("powerpc: Remove dead
CONFIG_HIGHPTE"), page tables are never allocated in high memory.
When the page is in low mem, kmap_atomic() just returns the page
address but still disable preemption and pagefault. And it is
not an inlined function, so we suffer function call for no reason.
Make pte_offset_map() the same as pte_offset_kernel() and make
pte_unmap() void, in the same way as PPC64 which doesn't have HIGHMEM.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/03c97f0f6b3790d164822563be80f2fd4713a955.1581932480.git.christophe.leroy@c-s.fr
The last jump to free_exit in mm_iommu_do_alloc() happens after page
pointers in struct mm_iommu_table_group_mem_t were already converted to
physical addresses. Thus calling put_page() on these physical addresses
will likely crash.
This moves the loop which calculates the pageshift and converts page
struct pointers to physical addresses later after the point when
we cannot fail; thus eliminating the need to convert pointers back.
Fixes: eb9d7a62c3 ("powerpc/mm_iommu: Fix potential deadlock")
Reported-by: Jan Kara <jack@suse.cz>
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20191223060351.26359-1-aik@ozlabs.ru
When calling debugfs functions, there is no need to ever check the
return value. The function can work or not, but the code logic should
never do something different based on this.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Oliver O'Halloran <oohall@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200209105901.1620958-6-gregkh@linuxfoundation.org
When calling debugfs functions, there is no need to ever check the
return value. The function can work or not, but the code logic should
never do something different based on this.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200209105901.1620958-5-gregkh@linuxfoundation.org
When calling debugfs functions, there is no need to ever check the
return value. The function can work or not, but the code logic should
never do something different based on this.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200209105901.1620958-4-gregkh@linuxfoundation.org
When calling debugfs functions, there is no need to ever check the
return value. The function can work or not, but the code logic should
never do something different based on this.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200209105901.1620958-3-gregkh@linuxfoundation.org
When calling debugfs functions, there is no need to ever check the
return value. The function can work or not, but the code logic should
never do something different based on this.
Because of this cleanup, we get to remove a few fields in struct
kvm_arch that are now unused.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[mpe: Fix build error in kvm/timing.c, adapt kvmppc_remove_cpu_debugfs()]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200209105901.1620958-2-gregkh@linuxfoundation.org
When calling debugfs functions, there is no need to ever check the
return value. The function can work or not, but the code logic should
never do something different based on this.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200209105901.1620958-1-gregkh@linuxfoundation.org
In some error handling path, we should call "of_node_put(np_par)" or
some resource may be leaking in case of error.
Fixes: 8159df72d4 ("83xx: add support for the kmeter1 board.")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Acked-by: Scott Wood <oss@buserror.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200208140920.7652-1-christophe.jaillet@wanadoo.fr
PowerVM systems running compatibility mode on a few Power8 revisions are
still vulnerable to the hardware defect that loses PMU exceptions arriving
prior to a context switch.
The software fix for this issue is enabled through the CPU_FTR_PMAO_BUG
cpu_feature bit, nevertheless this bit also needs to be set for PowerVM
compatibility mode systems.
Fixes: 68f2f0d431 ("powerpc: Add a cpu feature CPU_FTR_PMAO_BUG")
Signed-off-by: Desnes A. Nunes do Rosario <desnesn@linux.ibm.com>
Reviewed-by: Leonardo Bras <leonardo@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200227134715.9715-1-desnesn@linux.ibm.com
Commit 8d30c14cab ("powerpc/mm: Rework I$/D$ coherency (v3)") and
commit 90ac19a8b2 ("[POWERPC] Abolish iopa(), mm_ptov(),
io_block_mapping() from arch/powerpc") removed the use of get_pteptr()
outside of mm/pgtable_32.c
In mm/pgtable_32.c, the only user of get_pteptr() is change_page_attr()
which operates on kernel context and on lowmem pages only.
Make virt_to_kpte() available outside of mm/mem.c and use it instead
of get_pteptr(), and drop get_pteptr()
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/788378c6c3ba5c5298caab7c7f95e6c3c88244b8.1578558199.git.christophe.leroy@c-s.fr
At several places pmd pointer is retrieved through the same action:
pmd = pmd_offset(pud_offset(pgd_offset(mm, addr), addr), addr);
or
pmd = pmd_offset(pud_offset(pgd_offset_k(addr), addr), addr);
Refactor this by implementing two helpers pmd_ptr() and pmd_ptr_k()
This will help when adding the p4d level.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/7b065c5be35726af4066cab238ee35cabceda1fa.1578558199.git.christophe.leroy@c-s.fr
Since commit b86fb88855 ("powerpc/32: implement fast entry for
syscalls on non BOOKE") and commit 1a4b739bbb ("powerpc/32:
implement fast entry for syscalls on BOOKE"), syscalls don't
use the exception entry path anymore. It is therefore pointless
to restore r0 and r6-r8 after calling trace_hardirqs_off().
In the meantime, drop the '2:' label which is unused and misleading.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/d2c6dc65d27e83964eb05f16a126161ab6455eea.1578388585.git.christophe.leroy@c-s.fr
This kernel configuration is basically enabling/disabling sr driver quirks
detection. While these quirks are for fairly rare devices (very old CD
burners, and a glucometer), the additional detection of these models is a
very minimal amount of code.
The logic behind the quirks is always built into the sr driver.
This also removes the config from all the defconfig files that are enabling
this already.
Link: https://lore.kernel.org/r/20200223191144.726-1-flameeyes@flameeyes.com
Reviewed-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Diego Elio Pettenò <flameeyes@flameeyes.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Selecting CONFIG_DEBUG_INFO_BTF results in the below warning from ld:
ld: warning: orphan section `.BTF' from `.btf.vmlinux.bin.o' being placed in section `.BTF'
Include .BTF section in vmlinux explicitly to fix the same.
Signed-off-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200220113132.857132-1-naveen.n.rao@linux.vnet.ibm.com
DAR is set to the first byte of overlap between actual access and
watched range at DSI on Book3S processor. But actual access range
might or might not be within user asked range. So for Book3S, it
must not call dar_within_range().
This revert portion of commit 39413ae009 ("powerpc/hw_breakpoints:
Rewrite 8xx breakpoints to allow any address range size.").
Before patch:
# ./tools/testing/selftests/powerpc/ptrace/perf-hwbreak
...
TESTED: No overlap
FAILED: Partial overlap: 0 != 2
TESTED: Partial overlap
TESTED: No overlap
FAILED: Full overlap: 0 != 2
failure: perf_hwbreak
After patch:
TESTED: No overlap
TESTED: Partial overlap
TESTED: Partial overlap
TESTED: No overlap
TESTED: Full overlap
success: perf_hwbreak
Fixes: 39413ae009 ("powerpc/hw_breakpoints: Rewrite 8xx breakpoints to allow any address range size.")
Reported-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Ravi Bangoria <ravi.bangoria@linux.ibm.com>
Reviewed-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200222082049.330435-1-ravi.bangoria@linux.ibm.com
The "sub-section memory hotplug" facility allows memremap_pages() users
like libnvdimm to compensate for hardware platforms like x86 that have a
section size larger than their hardware memory mapping granularity. The
compensation that sub-section support affords is being tolerant of
physical memory resources shifting by units smaller (64MiB on x86) than
the memory-hotplug section size (128 MiB). Where the platform
physical-memory mapping granularity is limited by the number and
capability of address-decode-registers in the memory controller.
While the sub-section support allows memremap_pages() to operate on
sub-section (2MiB) granularity, the Power architecture may still
require 16MiB alignment on "!radix_enabled()" platforms.
In order for libnvdimm to be able to detect and manage this per-arch
limitation, introduce memremap_compat_align() as a common minimum
alignment across all driver-facing memory-mapping interfaces, and let
Power override it to 16MiB in the "!radix_enabled()" case.
The assumption / requirement for 16MiB to be a viable
memremap_compat_align() value is that Power does not have platforms
where its equivalent of address-decode-registers never hardware remaps a
persistent memory resource on smaller than 16MiB boundaries. Note that I
tried my best to not add a new Kconfig symbol, but header include
entanglements defeated the #ifndef memremap_compat_align design pattern
and the need to export it defeats the __weak design pattern for arch
overrides.
Based on an initial patch by Aneesh.
Link: http://lore.kernel.org/r/CAPcyv4gBGNP95APYaBcsocEa50tQj9b5h__83vgngjq3ouGX_Q@mail.gmail.com
Reported-by: Aneesh Kumar K.V <aneesh.kumar@linux.ibm.com>
Reported-by: Jeff Moyer <jmoyer@redhat.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Reviewed-by: Aneesh Kumar K.V <aneesh.kumar@linux.ibm.com>
Acked-by: Michael Ellerman <mpe@ellerman.id.au> (powerpc)
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
_tlbia() is a function used only on 603/603e core, ie on CPUs which
don't have a hash table.
_tlbia() uses the tlbia macro which implements a loop of 1024 tlbie.
On the 603/603e core, flushing the entire TLB requires no more than
32 tlbie.
Replace tlbia by a loop of 32 tlbie.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/12f4f4f0ff89aeab3b937fc96c84fb35e1b2517e.1580748445.git.christophe.leroy@c-s.fr
In guests without hotplugagble memory drmem structure is only zero
initialized. Trying to manipulate DLPAR parameters results in a crash.
$ echo "memory add count 1" > /sys/kernel/dlpar
Oops: Kernel access of bad area, sig: 11 [#1]
LE PAGE_SIZE=64K MMU=Hash SMP NR_CPUS=2048 NUMA pSeries
...
NIP: c0000000000ff294 LR: c0000000000ff248 CTR: 0000000000000000
REGS: c0000000fb9d3880 TRAP: 0300 Tainted: G E (5.5.0-rc6-2-default)
MSR: 8000000000009033 <SF,EE,ME,IR,DR,RI,LE> CR: 28242428 XER: 20000000
CFAR: c0000000009a6c10 DAR: 0000000000000010 DSISR: 40000000 IRQMASK: 0
...
NIP dlpar_memory+0x6e4/0xd00
LR dlpar_memory+0x698/0xd00
Call Trace:
dlpar_memory+0x698/0xd00 (unreliable)
handle_dlpar_errorlog+0xc0/0x190
dlpar_store+0x198/0x4a0
kobj_attr_store+0x30/0x50
sysfs_kf_write+0x64/0x90
kernfs_fop_write+0x1b0/0x290
__vfs_write+0x3c/0x70
vfs_write+0xd0/0x260
ksys_write+0xdc/0x130
system_call+0x5c/0x68
Taking closer look at the code, I can see that for_each_drmem_lmb is a
macro expanding into `for (lmb = &drmem_info->lmbs[0]; lmb <=
&drmem_info->lmbs[drmem_info->n_lmbs - 1]; lmb++)`. When drmem_info->lmbs
is NULL, the loop would iterate through the whole address range if it
weren't stopped by the NULL pointer dereference on the next line.
This patch aligns for_each_drmem_lmb and for_each_drmem_lmb_in_range
macro behavior with the common C semantics, where the end marker does
not belong to the scanned range, and alters get_lmb_range() semantics.
As a side effect, the wraparound observed in the crash is prevented.
Fixes: 6c6ea53725 ("powerpc/mm: Separate ibm, dynamic-memory data from DT format")
Cc: stable@vger.kernel.org # v4.16+
Signed-off-by: Libor Pechacek <lpechacek@suse.cz>
Signed-off-by: Michal Suchanek <msuchanek@suse.de>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200131132829.10281-1-msuchanek@suse.de
CR0 can be saved later, and CTR can also be used for saving.
Keep SRR1 in r9 and stash SRR0 in CTR, this avoids using thread_struct
in memory for that.
Saves 3 cycles (ie 1%) in null_syscall selftest on 8xx.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/b94c3bc03bac9431fec2dadb686384c481889422.1580470483.git.christophe.leroy@c-s.fr
Since commit b86fb88855 ("powerpc/32: implement fast entry for
syscalls on non BOOKE") and commit 1a4b739bbb ("powerpc/32:
implement fast entry for syscalls on BOOKE"), syscalls from
kernel are unexpected and can have catastrophic consequences
as it will destroy the kernel stack.
Test MSR_PR on syscall entry. In case syscall is from kernel,
emit a warning and return ENOSYS error.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/8ee3bdbbdfdfc64ca7001e90c43b2aee6f333578.1580470482.git.christophe.leroy@c-s.fr
When flushing any memory range, the flushing function
flushes all TLBs.
When (start) and (end - 1) are in the same memory page,
flush that page instead.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Reviewed-by: Segher Boessenkool <segher@kernel.crashing.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/b30b2eae6960502eaf0d9e36c60820b839693c33.1580542939.git.christophe.leroy@c-s.fr
Add a sys interface to allow querying the memory reserved by FADump for
saving the crash dump.
Also added Documentation/ABI for the new sysfs file.
Signed-off-by: Sourabh Jain <sourabhjain@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20191211160910.21656-7-sourabhjain@linux.ibm.com
The /sys/firmware/opal/core and /sys/kernel/fadump_release_opalcore
sysfs files are used to export and release the OPAL memory on PowerNV
platform. let's organize them into a new kobject under
/sys/firmware/opal/mpipl/ directory.
A symlink is added to maintain the backward compatibility for
/sys/firmware/opal/core sysfs file.
Signed-off-by: Sourabh Jain <sourabhjain@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20191211160910.21656-5-sourabhjain@linux.ibm.com
As the number of FADump sysfs files increases it is hard to manage all
of them inside /sys/kernel directory. It's better to have all the
FADump related sysfs files in a dedicated directory
/sys/kernel/fadump. But in order to maintain backward compatibility a
symlink has been added for every sysfs that has moved to new location.
As the FADump sysfs files are now part of a dedicated directory there
is no need to prefix their name with fadump_, hence sysfs file names
are also updated. For example fadump_enabled sysfs file is now
referred as enabled.
Also consolidate ABI documentation for all the FADump sysfs files in a
single file Documentation/ABI/testing/sysfs-kernel-fadump.
Signed-off-by: Sourabh Jain <sourabhjain@linux.ibm.com>
Tested-by: Michal Suchanek <msuchanek@suse.de>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20191211160910.21656-4-sourabhjain@linux.ibm.com
Function papr_scm_ndctl() is neither exported from the module nor
called directly from outside 'papr.c' hence should be marked 'static'.
Signed-off-by: Vaibhav Jain <vaibhav@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200130040206.79998-1-vaibhav@linux.ibm.com
The pseries Makefile (arch/powerpc/platforms/pseries/Makefile) is only
included by the platform Makefile (arch/powerpc/platform/Makefile)
when CONFIG_PPC_PSERIES is selected, so checking for
CONFIG_PPC_PSERIES in the pseries Makefile is pointless.
Signed-off-by: Oliver O'Halloran <oohall@gmail.com>
Reviewed-by: Tyrel Datwyler <tyreld@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200130063153.19915-2-oohall@gmail.com
vio.c is in platforms/pseries, which is only built if PPC_PSERIES=y.
In other words, this ifdef is pointless.
Signed-off-by: Oliver O'Halloran <oohall@gmail.com>
Reviewed-by: Tyrel Datwyler <tyreld@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200130063153.19915-1-oohall@gmail.com
The ls (lookup symbol) and zr (reboot) commands use xmon's getstring()
helper to read a string argument from the xmon prompt. This function
skips over leading whitespace, but doesn't check if the first
"non-whitespace" character is a newline which causes some odd
behaviour (<enter> indicates a the enter key was pressed):
0:mon> ls printk<enter>
printk: c0000000001680c4
0:mon> ls<enter>
printk<enter>
Symbol '
printk' not found.
0:mon>
With commit 2d9b332d99 ("powerpc/xmon: Allow passing an argument to
ppc_md.restart()") we have a similar problem with the zr command.
Previously zr took no arguments so "zr<enter> would trigger a reboot.
With that patch applied a second newline needs to be sent in order for
the reboot to occur. Fix this by checking if the leading whitespace
ended on a newline:
0:mon> ls<enter>
Symbol '' not found.
Fixes: 2d9b332d99 ("powerpc/xmon: Allow passing an argument to ppc_md.restart()")
Reported-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Oliver O'Halloran <oohall@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200217041343.2454-1-oohall@gmail.com
power_save_ppc32_restore() is called during exception entry, before
re-enabling the MMU. It substracts KERNELBASE from the address
of nap_save_msscr0 to access it.
With CONFIG_VMAP_STACK enabled, data MMU translation has already been
re-enabled, so power_save_ppc32_restore() has to access
nap_save_msscr0 by its virtual address.
Reported-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Fixes: cd08f109e2 ("powerpc/32s: Enable CONFIG_VMAP_STACK")
Tested-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/7bce32ccbab3ba3e3e0f27da6961bf6313df97ed.1581663140.git.christophe.leroy@c-s.fr
hash_page() needs to read page tables from kernel memory. When entire
kernel memory is mapped by BATs, which is normally the case when
CONFIG_STRICT_KERNEL_RWX is not set, it works even if the page hosting
the page table is not referenced in the MMU hash table.
However, if the page where the page table resides is not covered by
a BAT, a DSI fault can be encountered from hash_page(), and it loops
forever. This can happen when CONFIG_STRICT_KERNEL_RWX is selected
and the alignment of the different regions is too small to allow
covering the entire memory with BATs. This also happens when
CONFIG_DEBUG_PAGEALLOC is selected or when booting with 'nobats'
flag.
Also, if the page containing the kernel stack is not present in the
MMU hash table, registers cannot be saved and a recursive DSI fault
is encountered.
To allow hash_page() to properly do its job at all time and load the
MMU hash table whenever needed, it must run with data MMU disabled.
This means it must be called before re-enabling data MMU. To allow
this, registers clobbered by hash_page() and create_hpte() have to
be saved in the thread struct together with SRR0, SSR1, DAR and DSISR.
It is also necessary to ensure that DSI prolog doesn't overwrite
regs saved by prolog of the current running exception. That means:
- DSI can only use SPRN_SPRG_SCRATCH0
- Exceptions must free SPRN_SPRG_SCRATCH0 before writing to the stack.
This also fixes the Oops reported by Erhard when create_hpte() is
called by add_hash_page().
Due to prolog size increase, a few more exceptions had to get split
in two parts.
Fixes: cd08f109e2 ("powerpc/32s: Enable CONFIG_VMAP_STACK")
Reported-by: Erhard F. <erhard_f@mailbox.org>
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Tested-by: Erhard F. <erhard_f@mailbox.org>
Tested-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://bugzilla.kernel.org/show_bug.cgi?id=206501
Link: https://lore.kernel.org/r/64a4aa44686e9fd4b01333401367029771d9b231.1581761633.git.christophe.leroy@c-s.fr
After a treclaim, we expect to be in non-transactional state. If we
don't clear the current thread's MSR[TS] before we get preempted, then
tm_recheckpoint_new_task() will recheckpoint and we get rescheduled in
suspended transaction state.
When handling a signal caught in transactional state,
handle_rt_signal64() calls get_tm_stackpointer() that treclaims the
transaction using tm_reclaim_current() but without clearing the
thread's MSR[TS]. This can cause the TM Bad Thing exception below if
later we pagefault and get preempted trying to access the user's
sigframe, using __put_user(). Afterwards, when we are rescheduled back
into do_page_fault() (but now in suspended state since the thread's
MSR[TS] was not cleared), upon executing 'rfid' after completion of
the page fault handling, the exception is raised because a transition
from suspended to non-transactional state is invalid.
Unexpected TM Bad Thing exception at c00000000000de44 (msr 0x8000000302a03031) tm_scratch=800000010280b033
Oops: Unrecoverable exception, sig: 6 [#1]
LE PAGE_SIZE=64K MMU=Hash SMP NR_CPUS=2048 NUMA pSeries
CPU: 25 PID: 15547 Comm: a.out Not tainted 5.4.0-rc2 #32
NIP: c00000000000de44 LR: c000000000034728 CTR: 0000000000000000
REGS: c00000003fe7bd70 TRAP: 0700 Not tainted (5.4.0-rc2)
MSR: 8000000302a03031 <SF,VEC,VSX,FP,ME,IR,DR,LE,TM[SE]> CR: 44000884 XER: 00000000
CFAR: c00000000000dda4 IRQMASK: 0
PACATMSCRATCH: 800000010280b033
GPR00: c000000000034728 c000000f65a17c80 c000000001662800 00007fffacf3fd78
GPR04: 0000000000001000 0000000000001000 0000000000000000 c000000f611f8af0
GPR08: 0000000000000000 0000000078006001 0000000000000000 000c000000000000
GPR12: c000000f611f84b0 c00000003ffcb200 0000000000000000 0000000000000000
GPR16: 0000000000000000 0000000000000000 0000000000000000 0000000000000000
GPR20: 0000000000000000 0000000000000000 0000000000000000 c000000f611f8140
GPR24: 0000000000000000 00007fffacf3fd68 c000000f65a17d90 c000000f611f7800
GPR28: c000000f65a17e90 c000000f65a17e90 c000000001685e18 00007fffacf3f000
NIP [c00000000000de44] fast_exception_return+0xf4/0x1b0
LR [c000000000034728] handle_rt_signal64+0x78/0xc50
Call Trace:
[c000000f65a17c80] [c000000000034710] handle_rt_signal64+0x60/0xc50 (unreliable)
[c000000f65a17d30] [c000000000023640] do_notify_resume+0x330/0x460
[c000000f65a17e20] [c00000000000dcc4] ret_from_except_lite+0x70/0x74
Instruction dump:
7c4ff120 e8410170 7c5a03a6 38400000 f8410060 e8010070 e8410080 e8610088
60000000 60000000 e8810090 e8210078 <4c000024> 48000000 e8610178 88ed0989
---[ end trace 93094aa44b442f87 ]---
The simplified sequence of events that triggers the above exception is:
... # userspace in NON-TRANSACTIONAL state
tbegin # userspace in TRANSACTIONAL state
signal delivery # kernelspace in SUSPENDED state
handle_rt_signal64()
get_tm_stackpointer()
treclaim # kernelspace in NON-TRANSACTIONAL state
__put_user()
page fault happens. We will never get back here because of the TM Bad Thing exception.
page fault handling kicks in and we voluntarily preempt ourselves
do_page_fault()
__schedule()
__switch_to(other_task)
our task is rescheduled and we recheckpoint because the thread's MSR[TS] was not cleared
__switch_to(our_task)
switch_to_tm()
tm_recheckpoint_new_task()
trechkpt # kernelspace in SUSPENDED state
The page fault handling resumes, but now we are in suspended transaction state
do_page_fault() completes
rfid <----- trying to get back where the page fault happened (we were non-transactional back then)
TM Bad Thing # illegal transition from suspended to non-transactional
This patch fixes that issue by clearing the current thread's MSR[TS]
just after treclaim in get_tm_stackpointer() so that we stay in
non-transactional state in case we are preempted. In order to make
treclaim and clearing the thread's MSR[TS] atomic from a preemption
perspective when CONFIG_PREEMPT is set, preempt_disable/enable() is
used. It's also necessary to save the previous value of the thread's
MSR before get_tm_stackpointer() is called so that it can be exposed
to the signal handler later in setup_tm_sigcontexts() to inform the
userspace MSR at the moment of the signal delivery.
Found with tm-signal-context-force-tm kernel selftest.
Fixes: 2b0a576d15 ("powerpc: Add new transactional memory state to the signal context")
Cc: stable@vger.kernel.org # v3.9
Signed-off-by: Gustavo Luiz Duarte <gustavold@linux.ibm.com>
Acked-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200211033831.11165-1-gustavold@linux.ibm.com
In ITLB miss handled the line supposed to clear bits 20-23 on the L2
ITLB entry is buggy and does indeed nothing, leading to undefined
value which could allow execution when it shouldn't.
Properly do the clearing with the relevant instruction.
Fixes: 74fabcadfd ("powerpc/8xx: don't use r12/SPRN_SPRG_SCRATCH2 in TLB Miss handlers")
Cc: stable@vger.kernel.org # v5.0+
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Reviewed-by: Leonardo Bras <leonardo@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/4f70c2778163affce8508a210f65d140e84524b4.1581272050.git.christophe.leroy@c-s.fr
With HW assistance all page tables must be 4k aligned, the 8xx drops
the last 12 bits during the walk.
Redefine HUGEPD_SHIFT_MASK to mask last 12 bits out. HUGEPD_SHIFT_MASK
is used to for alignment of page table cache.
Fixes: 22569b881d ("powerpc/8xx: Enable 8M hugepage support with HW assistance")
Cc: stable@vger.kernel.org # v5.0+
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/778b1a248c4c7ca79640eeff7740044da6a220a0.1581264115.git.christophe.leroy@c-s.fr
Commit 55c8fc3f49 ("powerpc/8xx: reintroduce 16K pages with HW
assistance") redefined pte_t as a struct of 4 pte_basic_t, because
in 16K pages mode there are four identical entries in the
page table. But the size of hugepage tables is calculated based
of the size of (void *). Therefore, we end up with page tables
of size 1k instead of 4k for 512k pages.
As 512k hugepage tables are the same size as standard page tables,
ie 4k, use the standard page tables instead of PGT_CACHE tables.
Fixes: 3fb69c6a1a ("powerpc/8xx: Enable 512k hugepage support with HW assistance")
Cc: stable@vger.kernel.org # v5.0+
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/90ec56a2315be602494619ed0223bba3b0b8d619.1580997007.git.christophe.leroy@c-s.fr
Recovering a dead PHB can currently cause a deadlock as the PCI
rescan/remove lock is taken twice.
This is caused as part of an existing bug in
eeh_handle_special_event(). The pe is processed while traversing the
PHBs even though the pe is unrelated to the loop. This causes the pe
to be, incorrectly, processed more than once.
Untangling this section can move the pe processing out of the loop and
also outside the locked section, correcting both problems.
Fixes: 2e25505147 ("powerpc/eeh: Fix crash when edev->pdev changes")
Cc: stable@vger.kernel.org # 5.4+
Signed-off-by: Sam Bobroff <sbobroff@linux.ibm.com>
Reviewed-by: Frederic Barrat <fbarrat@linux.ibm.com>
Tested-by: Frederic Barrat <fbarrat@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/0547e82dbf90ee0729a2979a8cac5c91665c621f.1581051445.git.sbobroff@linux.ibm.com
Let's use the struct of_pci_range.flags field instead so we can remove
the pci_space field.
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: linuxppc-dev@lists.ozlabs.org
Signed-off-by: Rob Herring <robh@kernel.org>
A few archs (x86, arm, arm64) don't rely anymore on TIF_NOHZ to call
into context tracking on user entry/exit but instead use static keys
(or not) to optimize those calls. Ideally every arch should migrate to
that behaviour in the long run.
Settle a config option to let those archs remove their TIF_NOHZ
definitions.
Signed-off-by: Frederic Weisbecker <frederic@kernel.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will@kernel.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Paul Burton <paulburton@kernel.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: David S. Miller <davem@davemloft.net>
The low level index is the index in the underlying hardware buffer of
the most recently captured taken branch which is always saved in
branch_entries[0]. It is very useful for reconstructing the call stack.
For example, in Intel LBR call stack mode, the depth of reconstructed
LBR call stack limits to the number of LBR registers. With the low level
index information, perf tool may stitch the stacks of two samples. The
reconstructed LBR call stack can break the HW limitation.
Add a new branch sample type to retrieve low level index of raw branch
records. The low level index is between -1 (unknown) and max depth which
can be retrieved in /sys/devices/cpu/caps/branches.
Only when the new branch sample type is set, the low level index
information is dumped into the PERF_SAMPLE_BRANCH_STACK output.
Perf tool should check the attr.branch_sample_type, and apply the
corresponding format for PERF_SAMPLE_BRANCH_STACK samples.
Otherwise, some user case may be broken. For example, users may parse a
perf.data, which include the new branch sample type, with an old version
perf tool (without the check). Users probably get incorrect information
without any warning.
Signed-off-by: Kan Liang <kan.liang@linux.intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Link: https://lkml.kernel.org/r/20200127165355.27495-2-kan.liang@linux.intel.com
- fix randconfig to generate a sane .config
- rename hostprogs-y / always to hostprogs / always-y, which are
more natual syntax.
- optimize scripts/kallsyms
- fix yes2modconfig and mod2yesconfig
- make multiple directory targets ('make foo/ bar/') work
-----BEGIN PGP SIGNATURE-----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=sv4U
-----END PGP SIGNATURE-----
Merge tag 'kbuild-v5.6-2' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild
Pull more Kbuild updates from Masahiro Yamada:
- fix randconfig to generate a sane .config
- rename hostprogs-y / always to hostprogs / always-y, which are more
natual syntax.
- optimize scripts/kallsyms
- fix yes2modconfig and mod2yesconfig
- make multiple directory targets ('make foo/ bar/') work
* tag 'kbuild-v5.6-2' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild:
kbuild: make multiple directory targets work
kconfig: Invalidate all symbols after changing to y or m.
kallsyms: fix type of kallsyms_token_table[]
scripts/kallsyms: change table to store (strcut sym_entry *)
scripts/kallsyms: rename local variables in read_symbol()
kbuild: rename hostprogs-y/always to hostprogs/always-y
kbuild: fix the document to use extra-y for vmlinux.lds
kconfig: fix broken dependency in randconfig-generated .config
Fix an existing bug in our user access handling, exposed by one of the bug fixes
we merged this cycle.
A fix for a boot hang on 32-bit with CONFIG_TRACE_IRQFLAGS and the recently
added CONFIG_VMAP_STACK.
Thanks to:
Christophe Leroy, Guenter Roeck.
-----BEGIN PGP SIGNATURE-----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=+Urh
-----END PGP SIGNATURE-----
Merge tag 'powerpc-5.6-2' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc fixes from Michael Ellerman:
- Fix an existing bug in our user access handling, exposed by one of
the bug fixes we merged this cycle.
- A fix for a boot hang on 32-bit with CONFIG_TRACE_IRQFLAGS and the
recently added CONFIG_VMAP_STACK.
Thanks to: Christophe Leroy, Guenter Roeck.
* tag 'powerpc-5.6-2' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc: Fix CONFIG_TRACE_IRQFLAGS with CONFIG_VMAP_STACK
powerpc/futex: Fix incorrect user access blocking
Various driver updates for platforms:
- Nvidia: Fuse support for Tegra194, continued memory controller pieces
for Tegra30
- NXP/FSL: Refactorings of QuickEngine drivers to support ARM/ARM64/PPC
- NXP/FSL: i.MX8MP SoC driver pieces
- TI Keystone: ring accelerator driver
- Qualcomm: SCM driver cleanup/refactoring + support for new SoCs.
- Xilinx ZynqMP: feature checking interface for firmware. Mailbox
communication for power management
- Overall support patch set for cpuidle on more complex hierarchies
(PSCI-based)
+ Misc cleanups, refactorings of Marvell, TI, other platforms.
-----BEGIN PGP SIGNATURE-----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=ONtb
-----END PGP SIGNATURE-----
Merge tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC-related driver updates from Olof Johansson:
"Various driver updates for platforms:
- Nvidia: Fuse support for Tegra194, continued memory controller
pieces for Tegra30
- NXP/FSL: Refactorings of QuickEngine drivers to support
ARM/ARM64/PPC
- NXP/FSL: i.MX8MP SoC driver pieces
- TI Keystone: ring accelerator driver
- Qualcomm: SCM driver cleanup/refactoring + support for new SoCs.
- Xilinx ZynqMP: feature checking interface for firmware. Mailbox
communication for power management
- Overall support patch set for cpuidle on more complex hierarchies
(PSCI-based)
and misc cleanups, refactorings of Marvell, TI, other platforms"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (166 commits)
drivers: soc: xilinx: Use mailbox IPI callback
dt-bindings: power: reset: xilinx: Add bindings for ipi mailbox
drivers: soc: ti: knav_qmss_queue: Pass lockdep expression to RCU lists
MAINTAINERS: Add brcmstb PCIe controller entry
soc/tegra: fuse: Unmap registers once they are not needed anymore
soc/tegra: fuse: Correct straps' address for older Tegra124 device trees
soc/tegra: fuse: Warn if straps are not ready
soc/tegra: fuse: Cache values of straps and Chip ID registers
memory: tegra30-emc: Correct error message for timed out auto calibration
memory: tegra30-emc: Firm up hardware programming sequence
memory: tegra30-emc: Firm up suspend/resume sequence
soc/tegra: regulators: Do nothing if voltage is unchanged
memory: tegra: Correct reset value of xusb_hostr
soc/tegra: fuse: Add APB DMA dependency for Tegra20
bus: tegra-aconnect: Remove PM_CLK dependency
dt-bindings: mediatek: add MT6765 power dt-bindings
soc: mediatek: cmdq: delete not used define
memory: tegra: Add support for the Tegra194 memory controller
memory: tegra: Only include support for enabled SoCs
memory: tegra: Support DVFS on Tegra186 and later
...
Pull vfs file system parameter updates from Al Viro:
"Saner fs_parser.c guts and data structures. The system-wide registry
of syntax types (string/enum/int32/oct32/.../etc.) is gone and so is
the horror switch() in fs_parse() that would have to grow another case
every time something got added to that system-wide registry.
New syntax types can be added by filesystems easily now, and their
namespace is that of functions - not of system-wide enum members. IOW,
they can be shared or kept private and if some turn out to be widely
useful, we can make them common library helpers, etc., without having
to do anything whatsoever to fs_parse() itself.
And we already get that kind of requests - the thing that finally
pushed me into doing that was "oh, and let's add one for timeouts -
things like 15s or 2h". If some filesystem really wants that, let them
do it. Without somebody having to play gatekeeper for the variants
blessed by direct support in fs_parse(), TYVM.
Quite a bit of boilerplate is gone. And IMO the data structures make a
lot more sense now. -200LoC, while we are at it"
* 'merge.nfs-fs_parse.1' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (25 commits)
tmpfs: switch to use of invalfc()
cgroup1: switch to use of errorfc() et.al.
procfs: switch to use of invalfc()
hugetlbfs: switch to use of invalfc()
cramfs: switch to use of errofc() et.al.
gfs2: switch to use of errorfc() et.al.
fuse: switch to use errorfc() et.al.
ceph: use errorfc() and friends instead of spelling the prefix out
prefix-handling analogues of errorf() and friends
turn fs_param_is_... into functions
fs_parse: handle optional arguments sanely
fs_parse: fold fs_parameter_desc/fs_parameter_spec
fs_parser: remove fs_parameter_description name field
add prefix to fs_context->log
ceph_parse_param(), ceph_parse_mon_ips(): switch to passing fc_log
new primitive: __fs_parse()
switch rbd and libceph to p_log-based primitives
struct p_log, variants of warnf() et.al. taking that one instead
teach logfc() to handle prefices, give it saner calling conventions
get rid of cg_invalf()
...
When CONFIG_PROVE_LOCKING is selected together with (now default)
CONFIG_VMAP_STACK, kernel enter deadlock during boot.
At the point of checking whether interrupts are enabled or not, the
value of MSR saved on stack is read using the physical address of the
stack. But at this point, when using VMAP stack the DATA MMU
translation has already been re-enabled, leading to deadlock.
Don't use the physical address of the stack when
CONFIG_VMAP_STACK is set.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Reported-by: Guenter Roeck <linux@roeck-us.net>
Fixes: 028474876f ("powerpc/32: prepare for CONFIG_VMAP_STACK")
Tested-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/daeacdc0dec0416d1c587cc9f9e7191ad3068dc0.1581095957.git.christophe.leroy@c-s.fr
The early versions of our kernel user access prevention (KUAP) were
written by Russell and Christophe, and didn't have separate
read/write access.
At some point I picked up the series and added the read/write access,
but I failed to update the usages in futex.h to correctly allow read
and write.
However we didn't notice because of another bug which was causing the
low-level code to always enable read and write. That bug was fixed
recently in commit 1d8f739b07 ("powerpc/kuap: Fix set direction in
allow/prevent_user_access()").
futex_atomic_cmpxchg_inatomic() is passed the user address as %3 and
does:
1: lwarx %1, 0, %3
cmpw 0, %1, %4
bne- 3f
2: stwcx. %5, 0, %3
Which clearly loads and stores from/to %3. The logic in
arch_futex_atomic_op_inuser() is similar, so fix both of them to use
allow_read_write_user().
Without this fix, and with PPC_KUAP_DEBUG=y, we see eg:
Bug: Read fault blocked by AMR!
WARNING: CPU: 94 PID: 149215 at arch/powerpc/include/asm/book3s/64/kup-radix.h:126 __do_page_fault+0x600/0xf30
CPU: 94 PID: 149215 Comm: futex_requeue_p Tainted: G W 5.5.0-rc7-gcc9x-g4c25df5640ae #1
...
NIP [c000000000070680] __do_page_fault+0x600/0xf30
LR [c00000000007067c] __do_page_fault+0x5fc/0xf30
Call Trace:
[c00020138e5637e0] [c00000000007067c] __do_page_fault+0x5fc/0xf30 (unreliable)
[c00020138e5638c0] [c00000000000ada8] handle_page_fault+0x10/0x30
--- interrupt: 301 at cmpxchg_futex_value_locked+0x68/0xd0
LR = futex_lock_pi_atomic+0xe0/0x1f0
[c00020138e563bc0] [c000000000217b50] futex_lock_pi_atomic+0x80/0x1f0 (unreliable)
[c00020138e563c30] [c00000000021b668] futex_requeue+0x438/0xb60
[c00020138e563d60] [c00000000021c6cc] do_futex+0x1ec/0x2b0
[c00020138e563d90] [c00000000021c8b8] sys_futex+0x128/0x200
[c00020138e563e20] [c00000000000b7ac] system_call+0x5c/0x68
Fixes: de78a9c42a ("powerpc: Add a framework for Kernel Userspace Access Protection")
Cc: stable@vger.kernel.org # v5.2+
Reported-by: syzbot+e808452bad7c375cbee6@syzkaller-ppc64.appspotmail.com
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Reviewed-by: Christophe Leroy <christophe.leroy@c-s.fr>
Link: https://lore.kernel.org/r/20200207122145.11928-1-mpe@ellerman.id.au
Some bug fixes/cleanups.
Deprecated scsi passthrough for blk removed.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
iQFDBAABCAAtFiEEXQn9CHHI+FuUyooNKB8NuNKNVGkFAl49E/4PHG1zdEByZWRo
YXQuY29tAAoJECgfDbjSjVRpyecH/AlBzCOlv9kBHKvx30h2QTgbvZlZM++SRQ18
XAuvU/gRVTPLeSsXnJGz0hMD8hxBti6esqvxHzSzs2a6DqkqLrRdnMXsjs6QlAdX
6NwP4VesL7RNKTAjjrtmXQMr8iADtTy8FKCw/sZM+6sqhPeKAzFbBrjfH6amINru
orEF+eGwNXLkegK4+QVQx8f1rlIm7+/Z4lAP75FsaisYWLxklvn3VjZ7YjsCNexi
4zMxv64W8AHCRJK8k7/+vluedwwTghY9ayubw4zeRWmcfRw568bxlCZUQBmNWspC
lj4/ZWzGmd60UQx9fUvEd7T6QCRzaaUYVzXC0Mh8I3pLV+V5tKY=
=uqtg
-----END PGP SIGNATURE-----
Merge tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost
Pull virtio updates from Michael Tsirkin:
"Some bug fixes/cleanups.
The deprecated scsi passthrough for virtio_blk is removed"
* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost:
virtio_balloon: Fix memory leaks on errors in virtballoon_probe()
virtio-balloon: Fix memory leak when unloading while hinting is in progress
virtio_balloon: prevent pfn array overflow
virtio-blk: remove VIRTIO_BLK_F_SCSI support
virtio-pci: check name when counting MSI-X vectors
virtio-balloon: initialize all vq callbacks
virtio-mmio: convert to devm_platform_ioremap_resource
Unused now.
Signed-off-by: Eric Sandeen <sandeen@redhat.com>
Acked-by: David Howells <dhowells@redhat.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Since the need for a special flag to support SCSI passthrough on a
block device was added in May 2017 the SCSI passthrough support in
virtio-blk has been disabled. It has always been a bad idea
(just ask the original author..) and we have virtio-scsi for proper
passthrough. The feature also never made it into the virtio 1.0
or later specifications.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
- Implement user_access_begin() and friends for our platforms that support
controlling kernel access to userspace.
- Enable CONFIG_VMAP_STACK on 32-bit Book3S and 8xx.
- Some tweaks to our pseries IOMMU code to allow SVMs ("secure" virtual
machines) to use the IOMMU.
- Add support for CLOCK_{REALTIME/MONOTONIC}_COARSE to the 32-bit VDSO, and
some other improvements.
- A series to use the PCI hotplug framework to control opencapi card's so that
they can be reset and re-read after flashing a new FPGA image.
As well as other minor fixes and improvements as usual.
Thanks to:
Alastair D'Silva, Alexandre Ghiti, Alexey Kardashevskiy, Andrew Donnellan,
Aneesh Kumar K.V, Anju T Sudhakar, Bai Yingjie, Chen Zhou, Christophe Leroy,
Frederic Barrat, Greg Kurz, Jason A. Donenfeld, Joel Stanley, Jordan Niethe,
Julia Lawall, Krzysztof Kozlowski, Laurent Dufour, Laurentiu Tudor, Linus
Walleij, Michael Bringmann, Nathan Chancellor, Nicholas Piggin, Nick
Desaulniers, Oliver O'Halloran, Peter Ujfalusi, Pingfan Liu, Ram Pai, Randy
Dunlap, Russell Currey, Sam Bobroff, Sebastian Andrzej Siewior, Shawn
Anastasio, Stephen Rothwell, Steve Best, Sukadev Bhattiprolu, Thiago Jung
Bauermann, Tyrel Datwyler, Vaibhav Jain.
-----BEGIN PGP SIGNATURE-----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=xpG+
-----END PGP SIGNATURE-----
Merge tag 'powerpc-5.6-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc updates from Michael Ellerman:
"A pretty small batch for us, and apologies for it being a bit late, I
wanted to sneak Christophe's user_access_begin() series in.
Summary:
- Implement user_access_begin() and friends for our platforms that
support controlling kernel access to userspace.
- Enable CONFIG_VMAP_STACK on 32-bit Book3S and 8xx.
- Some tweaks to our pseries IOMMU code to allow SVMs ("secure"
virtual machines) to use the IOMMU.
- Add support for CLOCK_{REALTIME/MONOTONIC}_COARSE to the 32-bit
VDSO, and some other improvements.
- A series to use the PCI hotplug framework to control opencapi
card's so that they can be reset and re-read after flashing a new
FPGA image.
As well as other minor fixes and improvements as usual.
Thanks to: Alastair D'Silva, Alexandre Ghiti, Alexey Kardashevskiy,
Andrew Donnellan, Aneesh Kumar K.V, Anju T Sudhakar, Bai Yingjie, Chen
Zhou, Christophe Leroy, Frederic Barrat, Greg Kurz, Jason A.
Donenfeld, Joel Stanley, Jordan Niethe, Julia Lawall, Krzysztof
Kozlowski, Laurent Dufour, Laurentiu Tudor, Linus Walleij, Michael
Bringmann, Nathan Chancellor, Nicholas Piggin, Nick Desaulniers,
Oliver O'Halloran, Peter Ujfalusi, Pingfan Liu, Ram Pai, Randy Dunlap,
Russell Currey, Sam Bobroff, Sebastian Andrzej Siewior, Shawn
Anastasio, Stephen Rothwell, Steve Best, Sukadev Bhattiprolu, Thiago
Jung Bauermann, Tyrel Datwyler, Vaibhav Jain"
* tag 'powerpc-5.6-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: (131 commits)
powerpc: configs: Cleanup old Kconfig options
powerpc/configs/skiroot: Enable some more hardening options
powerpc/configs/skiroot: Disable xmon default & enable reboot on panic
powerpc/configs/skiroot: Enable security features
powerpc/configs/skiroot: Update for symbol movement only
powerpc/configs/skiroot: Drop default n CONFIG_CRYPTO_ECHAINIV
powerpc/configs/skiroot: Drop HID_LOGITECH
powerpc/configs: Drop NET_VENDOR_HP which moved to staging
powerpc/configs: NET_CADENCE became NET_VENDOR_CADENCE
powerpc/configs: Drop CONFIG_QLGE which moved to staging
powerpc: Do not consider weak unresolved symbol relocations as bad
powerpc/32s: Fix kasan_early_hash_table() for CONFIG_VMAP_STACK
powerpc: indent to improve Kconfig readability
powerpc: Provide initial documentation for PAPR hcalls
powerpc: Implement user_access_save() and user_access_restore()
powerpc: Implement user_access_begin and friends
powerpc/32s: Prepare prevent_user_access() for user_access_end()
powerpc/32s: Drop NULL addr verification
powerpc/kuap: Fix set direction in allow/prevent_user_access()
powerpc/32s: Fix bad_kuap_fault()
...
Towards a more consistent naming scheme.
Link: http://lkml.kernel.org/r/20200116064531.483522-8-aneesh.kumar@linux.ibm.com
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.ibm.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Architectures for which we have hardware walkers of Linux page table
should flush TLB on mmu gather batch allocation failures and batch flush.
Some architectures like POWER supports multiple translation modes (hash
and radix) and in the case of POWER only radix translation mode needs the
above TLBI. This is because for hash translation mode kernel wants to
avoid this extra flush since there are no hardware walkers of linux page
table. With radix translation, the hardware also walks linux page table
and with that, kernel needs to make sure to TLB invalidate page walk cache
before page table pages are freed.
More details in commit d86564a2f0 ("mm/tlb, x86/mm: Support invalidating
TLB caches for RCU_TABLE_FREE")
The changes to sparc are to make sure we keep the old behavior since we
are now removing HAVE_RCU_TABLE_NO_INVALIDATE. The default value for
tlb_needs_table_invalidate is to always force an invalidate and sparc can
avoid the table invalidate. Hence we define tlb_needs_table_invalidate to
false for sparc architecture.
Link: http://lkml.kernel.org/r/20200116064531.483522-3-aneesh.kumar@linux.ibm.com
Fixes: a46cc7a90f ("powerpc/mm/radix: Improve TLB/PWC flushes")
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.ibm.com>
Acked-by: Michael Ellerman <mpe@ellerman.id.au> [powerpc]
Cc: <stable@vger.kernel.org> [4.14+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Patch series "Fixup page directory freeing", v4.
This is a repost of patch series from Peter with the arch specific changes
except ppc64 dropped. ppc64 changes are added here because we are redoing
the patch series on top of ppc64 changes. This makes it easy to backport
these changes. Only the first 2 patches need to be backported to stable.
The thing is, on anything SMP, freeing page directories should observe the
exact same order as normal page freeing:
1) unhook page/directory
2) TLB invalidate
3) free page/directory
Without this, any concurrent page-table walk could end up with a
Use-after-Free. This is esp. trivial for anything that has software
page-table walkers (HAVE_FAST_GUP / software TLB fill) or the hardware
caches partial page-walks (ie. caches page directories).
Even on UP this might give issues since mmu_gather is preemptible these
days. An interrupt or preempted task accessing user pages might stumble
into the free page if the hardware caches page directories.
This patch series fixes ppc64 and add generic MMU_GATHER changes to
support the conversion of other architectures. I haven't added patches
w.r.t other architecture because they are yet to be acked.
This patch (of 9):
A followup patch is going to make sure we correctly invalidate page walk
cache before we free page table pages. In order to keep things simple
enable RCU_TABLE_FREE even for !SMP so that we don't have to fixup the
!SMP case differently in the followup patch
!SMP case is right now broken for radix translation w.r.t page walk
cache flush. We can get interrupted in between page table free and
that would imply we have page walk cache entries pointing to tables
which got freed already. Michael said "both our platforms that run on
Power9 force SMP on in Kconfig, so the !SMP case is unlikely to be a
problem for anyone in practice, unless they've hacked their kernel to
build it !SMP."
Link: http://lkml.kernel.org/r/20200116064531.483522-2-aneesh.kumar@linux.ibm.com
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.ibm.com>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Acked-by: Michael Ellerman <mpe@ellerman.id.au>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
walk_page_range() is going to be allowed to walk page tables other than
those of user space. For this it needs to know when it has reached a
'leaf' entry in the page tables. This information is provided by the
p?d_leaf() functions/macros.
For powerpc p?d_is_leaf() functions already exist. Export them using the
new p?d_leaf() name.
Link: http://lkml.kernel.org/r/20191218162402.45610-7-steven.price@arm.com
Signed-off-by: Steven Price <steven.price@arm.com>
Acked-by: Michael Ellerman <mpe@ellerman.id.au>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Albert Ou <aou@eecs.berkeley.edu>
Cc: Alexandre Ghiti <alex@ghiti.fr>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: James Hogan <jhogan@kernel.org>
Cc: James Morse <james.morse@arm.com>
Cc: Jerome Glisse <jglisse@redhat.com>
Cc: "Liang, Kan" <kan.liang@linux.intel.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Paul Burton <paul.burton@mips.com>
Cc: Paul Walmsley <paul.walmsley@sifive.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vasily Gorbik <gor@linux.ibm.com>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Will Deacon <will@kernel.org>
Cc: Zong Li <zong.li@sifive.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In old days, the "host-progs" syntax was used for specifying host
programs. It was renamed to the current "hostprogs-y" in 2004.
It is typically useful in scripts/Makefile because it allows Kbuild to
selectively compile host programs based on the kernel configuration.
This commit renames like follows:
always -> always-y
hostprogs-y -> hostprogs
So, scripts/Makefile will look like this:
always-$(CONFIG_BUILD_BIN2C) += ...
always-$(CONFIG_KALLSYMS) += ...
...
hostprogs := $(always-y) $(always-m)
I think this makes more sense because a host program is always a host
program, irrespective of the kernel configuration. We want to specify
which ones to compile by CONFIG options, so always-y will be handier.
The "always", "hostprogs-y", "hostprogs-m" will be kept for backward
compatibility for a while.
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
CRNG hasn't initialized, instead of the old blocking pool. Also clean
up archrandom.h, and some other miscellaneous cleanups.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEK2m5VNv+CHkogTfJ8vlZVpUNgaMFAl40j1kACgkQ8vlZVpUN
gaPCywf8CWS9HFd2Iipj60gkTVugjlL5ib0lbfhQcAAwwzw1GLTXJSMBzzoMRHY/
ZI2sJZS1m0V1oWNnXXVKi+A1VXmlValWXAc+7fvbeaIe5pRT1EHP14s4Kz7/4d8Q
dk0b8cxNpR8u5CcbN8y9D+71IKpdksUbX7uGuGfw3bncQdRNwJVf+oS1fMGS0Rsb
F8ddQaED7iFpX2BMl56afQ4t2t0LA5+eLYMGoYoJx5fgd9BseP0TEcjj9Y4Z30M7
+GO4NZjUbAY0syx9r8hx3P/5miWZm2J9QJmJoXHhr5+IcAKM+6+Uo6X6gkOEqV4i
U//V1cqNuowV5ckE4Na+MfBillinsQ==
=HeFM
-----END PGP SIGNATURE-----
Merge tag 'random_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/random
Pull random changes from Ted Ts'o:
"Change /dev/random so that it uses the CRNG and only blocking if the
CRNG hasn't initialized, instead of the old blocking pool. Also clean
up archrandom.h, and some other miscellaneous cleanups"
* tag 'random_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/random: (24 commits)
s390x: Mark archrandom.h functions __must_check
powerpc: Mark archrandom.h functions __must_check
powerpc: Use bool in archrandom.h
x86: Mark archrandom.h functions __must_check
linux/random.h: Mark CONFIG_ARCH_RANDOM functions __must_check
linux/random.h: Use false with bool
linux/random.h: Remove arch_has_random, arch_has_random_seed
s390: Remove arch_has_random, arch_has_random_seed
powerpc: Remove arch_has_random, arch_has_random_seed
x86: Remove arch_has_random, arch_has_random_seed
random: remove some dead code of poolinfo
random: fix typo in add_timer_randomness()
random: Add and use pr_fmt()
random: convert to ENTROPY_BITS for better code readability
random: remove unnecessary unlikely()
random: remove kernel.random.read_wakeup_threshold
random: delete code to pull data into pools
random: remove the blocking pool
random: make /dev/random be almost like /dev/urandom
random: ignore GRND_RANDOM in getentropy(2)
...
Pull updates from Andrew Morton:
"Most of -mm and quite a number of other subsystems: hotfixes, scripts,
ocfs2, misc, lib, binfmt, init, reiserfs, exec, dma-mapping, kcov.
MM is fairly quiet this time. Holidays, I assume"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (118 commits)
kcov: ignore fault-inject and stacktrace
include/linux/io-mapping.h-mapping: use PHYS_PFN() macro in io_mapping_map_atomic_wc()
execve: warn if process starts with executable stack
reiserfs: prevent NULL pointer dereference in reiserfs_insert_item()
init/main.c: fix misleading "This architecture does not have kernel memory protection" message
init/main.c: fix quoted value handling in unknown_bootoption
init/main.c: remove unnecessary repair_env_string in do_initcall_level
init/main.c: log arguments and environment passed to init
fs/binfmt_elf.c: coredump: allow process with empty address space to coredump
fs/binfmt_elf.c: coredump: delete duplicated overflow check
fs/binfmt_elf.c: coredump: allocate core ELF header on stack
fs/binfmt_elf.c: make BAD_ADDR() unlikely
fs/binfmt_elf.c: better codegen around current->mm
fs/binfmt_elf.c: don't copy ELF header around
fs/binfmt_elf.c: fix ->start_code calculation
fs/binfmt_elf.c: smaller code generation around auxv vector fill
lib/find_bit.c: uninline helper _find_next_bit()
lib/find_bit.c: join _find_next_bit{_le}
uapi: rename ext2_swab() to swab() and share globally in swab.h
lib/scatterlist.c: adjust indentation in __sg_alloc_table
...
In order to provide a clearer, more symmetric API for pinning and
unpinning DMA pages. This way, pin_user_pages*() calls match up with
unpin_user_pages*() calls, and the API is a lot closer to being
self-explanatory.
Link: http://lkml.kernel.org/r/20200107224558.2362728-23-jhubbard@nvidia.com
Signed-off-by: John Hubbard <jhubbard@nvidia.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Cc: Alex Williamson <alex.williamson@redhat.com>
Cc: Aneesh Kumar K.V <aneesh.kumar@linux.ibm.com>
Cc: Björn Töpel <bjorn.topel@intel.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Cc: Ira Weiny <ira.weiny@intel.com>
Cc: Jason Gunthorpe <jgg@mellanox.com>
Cc: Jason Gunthorpe <jgg@ziepe.ca>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Jerome Glisse <jglisse@redhat.com>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Kirill A. Shutemov <kirill@shutemov.name>
Cc: Leon Romanovsky <leonro@mellanox.com>
Cc: Mauro Carvalho Chehab <mchehab@kernel.org>
Cc: Mike Rapoport <rppt@linux.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
1. Convert from get_user_pages() to pin_user_pages().
2. As required by pin_user_pages(), release these pages via
put_user_page().
Link: http://lkml.kernel.org/r/20200107224558.2362728-21-jhubbard@nvidia.com
Signed-off-by: John Hubbard <jhubbard@nvidia.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Cc: Alex Williamson <alex.williamson@redhat.com>
Cc: Aneesh Kumar K.V <aneesh.kumar@linux.ibm.com>
Cc: Björn Töpel <bjorn.topel@intel.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Cc: Ira Weiny <ira.weiny@intel.com>
Cc: Jason Gunthorpe <jgg@mellanox.com>
Cc: Jason Gunthorpe <jgg@ziepe.ca>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Jerome Glisse <jglisse@redhat.com>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Kirill A. Shutemov <kirill@shutemov.name>
Cc: Leon Romanovsky <leonro@mellanox.com>
Cc: Mauro Carvalho Chehab <mchehab@kernel.org>
Cc: Mike Rapoport <rppt@linux.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
PPC: Bugfixes
x86:
* Support for mapping DAX areas with large nested page table entries.
* Cleanups and bugfixes here too. A particularly important one is
a fix for FPU load when the thread has TIF_NEED_FPU_LOAD. There is
also a race condition which could be used in guest userspace to exploit
the guest kernel, for which the embargo expired today.
* Fast path for IPI delivery vmexits, shaving about 200 clock cycles
from IPI latency.
* Protect against "Spectre-v1/L1TF" (bring data in the cache via
speculative out of bound accesses, use L1TF on the sibling hyperthread
to read it), which unfortunately is an even bigger whack-a-mole game
than SpectreV1.
Sean continues his mission to rewrite KVM. In addition to a sizable
number of x86 patches, this time he contributed a pretty large refactoring
of vCPU creation that affects all architectures but should not have any
visible effect.
s390 will come next week together with some more x86 patches.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iQEcBAABAgAGBQJeMxtCAAoJEL/70l94x66DQxIIAJv9hMmXLQHGFnUMskjGErR6
DCLSC0YRdRMwE50CerblyJtGsMwGsPyHZwvZxoAceKJ9w0Yay9cyaoJ87ItBgHoY
ce0HrqIUYqRSJ/F8WH2lSzkzMBr839rcmqw8p1tt4D5DIsYnxHGWwRaaP+5M/1KQ
YKFu3Hea4L00U339iIuDkuA+xgz92LIbsn38svv5fxHhPAyWza0rDEYHNgzMKuoF
IakLf5+RrBFAh6ZuhYWQQ44uxjb+uQa9pVmcqYzzTd5t1g4PV5uXtlJKesHoAvik
Eba8IEUJn+HgQJjhp3YxQYuLeWOwRF3bwOiZ578MlJ4OPfYXMtbdlqCQANHOcGk=
=H/q1
-----END PGP SIGNATURE-----
Merge tag 'kvm-5.6-1' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull KVM updates from Paolo Bonzini:
"This is the first batch of KVM changes.
ARM:
- cleanups and corner case fixes.
PPC:
- Bugfixes
x86:
- Support for mapping DAX areas with large nested page table entries.
- Cleanups and bugfixes here too. A particularly important one is a
fix for FPU load when the thread has TIF_NEED_FPU_LOAD. There is
also a race condition which could be used in guest userspace to
exploit the guest kernel, for which the embargo expired today.
- Fast path for IPI delivery vmexits, shaving about 200 clock cycles
from IPI latency.
- Protect against "Spectre-v1/L1TF" (bring data in the cache via
speculative out of bound accesses, use L1TF on the sibling
hyperthread to read it), which unfortunately is an even bigger
whack-a-mole game than SpectreV1.
Sean continues his mission to rewrite KVM. In addition to a sizable
number of x86 patches, this time he contributed a pretty large
refactoring of vCPU creation that affects all architectures but should
not have any visible effect.
s390 will come next week together with some more x86 patches"
* tag 'kvm-5.6-1' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (204 commits)
x86/KVM: Clean up host's steal time structure
x86/KVM: Make sure KVM_VCPU_FLUSH_TLB flag is not missed
x86/kvm: Cache gfn to pfn translation
x86/kvm: Introduce kvm_(un)map_gfn()
x86/kvm: Be careful not to clear KVM_VCPU_FLUSH_TLB bit
KVM: PPC: Book3S PR: Fix -Werror=return-type build failure
KVM: PPC: Book3S HV: Release lock on page-out failure path
KVM: arm64: Treat emulated TVAL TimerValue as a signed 32-bit integer
KVM: arm64: pmu: Only handle supported event counters
KVM: arm64: pmu: Fix chained SW_INCR counters
KVM: arm64: pmu: Don't mark a counter as chained if the odd one is disabled
KVM: arm64: pmu: Don't increment SW_INCR if PMCR.E is unset
KVM: x86: Use a typedef for fastop functions
KVM: X86: Add 'else' to unify fastop and execute call path
KVM: x86: inline memslot_valid_for_gpte
KVM: x86/mmu: Use huge pages for DAX-backed files
KVM: x86/mmu: Remove lpage_is_disallowed() check from set_spte()
KVM: x86/mmu: Fold max_mapping_level() into kvm_mmu_hugepage_adjust()
KVM: x86/mmu: Zap any compound page when collapsing sptes
KVM: x86/mmu: Remove obsolete gfn restoration in FNAME(fetch)
...
CONFIG_ENABLE_WARN_DEPRECATED is gone since
commit 771c035372 ("deprecate the '__deprecated' attribute warnings
entirely and for good").
CONFIG_IOSCHED_DEADLINE and CONFIG_IOSCHED_CFQ are gone since
commit f382fb0bce ("block: remove legacy IO schedulers").
The IOSCHED_DEADLINE was replaced by MQ_IOSCHED_DEADLINE and it will be
now enabled by default (along with MQ_IOSCHED_KYBER).
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200130195223.3843-1-krzk@kernel.org
Enable more hardening options.
Note BUG_ON_DATA_CORRUPTION selects DEBUG_LIST and is essentially just
a synonym for it.
DEBUG_SG, DEBUG_NOTIFIERS, DEBUG_LIST, DEBUG_CREDENTIALS and
SCHED_STACK_END_CHECK should all be low overhead and just add a few
extra checks.
SLAB_FREELIST_RANDOM, and SLUB_DEBUG_ON will add some overhead to the
SLAB allocator, but nothing that should be meaningful for skiroot.
Unselecting SLAB_MERGE_DEFAULT causes the SLAB to use more memory, but
the skiroot kernel shouldn't be memory constrained on any of our
systems, all it does is run a small bootloader.
Disabling merging has some security/robustness benefit as it means a
user-after-free or overflow will be limited to the objects in that
slab, rather than potentially affecting objects from unrelated slabs
that have been merged.
Note also that slab merging is disabled anyway by enabling
SLUB_DEBUG_ON, because of the SLAB_NEVER_MERGE mask.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Acked-by: Joel Stanley <joel@jms.id.au>
Link: https://lore.kernel.org/r/20200121043000.16212-9-mpe@ellerman.id.au
If the skiroot kernel crashes we don't want it sitting at an xmon
prompt forever. Instead it's more helpful to reboot and bring the
boot loader back up, and if the crash was transient we can then boot
successfully.
Similarly if we panic we should reboot, with a short timeout in case
someone is watching the console.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Acked-by: Joel Stanley <joel@jms.id.au>
Link: https://lore.kernel.org/r/20200121043000.16212-8-mpe@ellerman.id.au
This turns on HARDENED_USERCOPY with HARDENED_USERCOPY_PAGESPAN, and
FORTIFY_SOURCE.
It also enables SECURITY_LOCKDOWN_LSM with _EARLY and
LOCK_DOWN_KERNEL_FORCE_INTEGRITY options enabled. This still allows
xmon to be used in read-only mode.
MODULE_SIG is selected by lockdown, so it is still enabled.
Because we're setting LOCK_DOWN_KERNELFORCE_INTEGRITY=y we also need
to enable KEXEC_FILE=y so that kexec continues to work.
Signed-off-by: Joel Stanley <joel@jms.id.au>
[mpe: Switch to lockdown integrity mode per oohal, enable KEXEC_FILE
as reported by jms]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200121043000.16212-7-mpe@ellerman.id.au
Commit bdd08fff49 ("HID: logitech: Add depends on LEDS_CLASS to
Logitech Kconfig entry") made HID_LOGITECH depend on LEDS_CLASS which
we do not enable, meaning we are not actually enabling those drivers
any more.
The Kconfig help text suggests USB HID compliant Logictech devices
will continue to work without HID_LOGITECH, so just drop it.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Acked-by: Joel Stanley <joel@jms.id.au>
Link: https://lore.kernel.org/r/20200121043000.16212-4-mpe@ellerman.id.au
The HP network driver moved to staging in commit 52340b82cf ("hp100:
Move 100BaseVG AnyLAN driver to staging") meaning we don't need to
disable it any more in our defconfigs.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Acked-by: Joel Stanley <joel@jms.id.au>
Link: https://lore.kernel.org/r/20200121043000.16212-3-mpe@ellerman.id.au
The NET_CADENCE symbol was renamed to NET_VENDOR_CADENCE, so we don't
need to disable the former, see commit 0df5f81c48 ("net: ethernet:
Add missing VENDOR to Cadence and Packet Engines symbols").
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Acked-by: Joel Stanley <joel@jms.id.au>
Link: https://lore.kernel.org/r/20200121043000.16212-2-mpe@ellerman.id.au
The QLGE driver moved to staging in commit 955315b0dc ("qlge: Move
drivers/net/ethernet/qlogic/qlge/ to drivers/staging/qlge/"), meaning
our defconfigs that enable it have no effect as we don't enable
CONFIG_STAGING.
It sounds like the device is obsolete, so drop the driver.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Acked-by: Joel Stanley <joel@jms.id.au>
Link: https://lore.kernel.org/r/20200121043000.16212-1-mpe@ellerman.id.au
Commit 8580ac9404 ("bpf: Process in-kernel BTF") introduced two weak
symbols that may be unresolved at link time which result in an absolute
relocation to 0. relocs_check.sh emits the following warning:
"WARNING: 2 bad relocations
c000000001a41478 R_PPC64_ADDR64 _binary__btf_vmlinux_bin_start
c000000001a41480 R_PPC64_ADDR64 _binary__btf_vmlinux_bin_end"
whereas those relocations are legitimate even for a relocatable kernel
compiled with -pie option.
relocs_check.sh already excluded some weak unresolved symbols explicitly:
remove those hardcoded symbols and add some logic that parses the symbols
using nm, retrieves all the weak unresolved symbols and excludes those from
the list of the potential bad relocations.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Alexandre Ghiti <alex@ghiti.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200118170335.21440-1-alex@ghiti.fr
Unfortunately, GCC 9.1 is expected to be be released without support for
MPX. This means that there was only a relatively small window where
folks could have ever used MPX. It failed to gain wide adoption in the
industry, and Linux was the only mainstream OS to ever support it widely.
Support for the feature may also disappear on future processors.
This set completes the process that we started during the 5.4 merge window.
-----BEGIN PGP SIGNATURE-----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=g4cC
-----END PGP SIGNATURE-----
Merge tag 'mpx-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/daveh/x86-mpx
Pull x86 MPX removal from Dave Hansen:
"MPX requires recompiling applications, which requires compiler
support. Unfortunately, GCC 9.1 is expected to be be released without
support for MPX. This means that there was only a relatively small
window where folks could have ever used MPX. It failed to gain wide
adoption in the industry, and Linux was the only mainstream OS to ever
support it widely.
Support for the feature may also disappear on future processors.
This set completes the process that we started during the 5.4 merge
window when the MPX prctl()s were removed. XSAVE support is left in
place, which allows MPX-using KVM guests to continue to function"
* tag 'mpx-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/daveh/x86-mpx:
x86/mpx: remove MPX from arch/x86
mm: remove arch_bprm_mm_init() hook
x86/mpx: remove bounds exception code
x86/mpx: remove build infrastructure
x86/alternatives: add missing insn.h include
* Fix compile warning on 32-bit machines
* Fix locking error in secure VM support
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQEcBAABCAAGBQJeMiC8AAoJEJ2a6ncsY3GfGg8H/03p+jc/aCKcA75ZeQPlzhmu
KWvSBbPATNcQiYOLfIvbB9AMXUPoyIfiblW/On8G6COFypsIhhUTwEfPUjWIBHNX
IwCfzoyf0gDRTi7A7gTDD06ZE+stikxJu59agX2Gc8kTIQ8ge340VR8J95Ol8/n2
/hVA8S/ORrdv8/KaCcvvIwc1V7OV6xBuGsTUOUvywzBTGDKd0CAbNzRwtS8LmWcM
OCkZX4G5DpFIYdsnjSBaSfwEVPAf3G1DzyQ801emwRnbAGYYgfakd1LwqdLDxptt
6CFHuIENEmmweJKMf9FBLWg+fOMl8wsv9l4mBIYt7coq5XPpi07yJ6yqSaJEToQ=
=Hmfo
-----END PGP SIGNATURE-----
Merge tag 'kvm-ppc-next-5.6-2' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc into HEAD
Second KVM PPC update for 5.6
* Fix compile warning on 32-bit machines
* Fix locking error in secure VM support
On book3s/32 CPUs that are handling MMU through a hash table,
MMU_init_hw() function was adapted for VMAP_STACK in order to
handle virtual addresses instead of physical addresses in the
low level hash functions.
When using KASAN, the same adaptations are required for the
early hash table set up by kasan_early_hash_table() function.
Fixes: cd08f109e2 ("powerpc/32s: Enable CONFIG_VMAP_STACK")
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/fc8390a33c2a470105f01abbcbdc7916c30c0a54.1580301269.git.christophe.leroy@c-s.fr
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQRAhzRXHqcMeLMyaSiRxhvAZXjcogUCXjFo8wAKCRCRxhvAZXjc
omaGAQDVwCHQekqxp2eC8EJH4Pkt+Bn1BLrA25stlTo93YBPHgEAsPVUCRNcrZAl
VncYmxCfpt3Yu0S/MTVXu5xrRiIXPQk=
=uqTN
-----END PGP SIGNATURE-----
Merge tag 'threads-v5.6' of git://git.kernel.org/pub/scm/linux/kernel/git/brauner/linux
Pull thread management updates from Christian Brauner:
"Sargun Dhillon over the last cycle has worked on the pidfd_getfd()
syscall.
This syscall allows for the retrieval of file descriptors of a process
based on its pidfd. A task needs to have ptrace_may_access()
permissions with PTRACE_MODE_ATTACH_REALCREDS (suggested by Oleg and
Andy) on the target.
One of the main use-cases is in combination with seccomp's user
notification feature. As a reminder, seccomp's user notification
feature was made available in v5.0. It allows a task to retrieve a
file descriptor for its seccomp filter. The file descriptor is usually
handed of to a more privileged supervising process. The supervisor can
then listen for syscall events caught by the seccomp filter of the
supervisee and perform actions in lieu of the supervisee, usually
emulating syscalls. pidfd_getfd() is needed to expand its uses.
There are currently two major users that wait on pidfd_getfd() and one
future user:
- Netflix, Sargun said, is working on a service mesh where users
should be able to connect to a dns-based VIP. When a user connects
to e.g. 1.2.3.4:80 that runs e.g. service "foo" they will be
redirected to an envoy process. This service mesh uses seccomp user
notifications and pidfd to intercept all connect calls and instead
of connecting them to 1.2.3.4:80 connects them to e.g.
127.0.0.1:8080.
- LXD uses the seccomp notifier heavily to intercept and emulate
mknod() and mount() syscalls for unprivileged containers/processes.
With pidfd_getfd() more uses-cases e.g. bridging socket connections
will be possible.
- The patchset has also seen some interest from the browser corner.
Right now, Firefox is using a SECCOMP_RET_TRAP sandbox managed by a
broker process. In the future glibc will start blocking all signals
during dlopen() rendering this type of sandbox impossible. Hence,
in the future Firefox will switch to a seccomp-user-nofication
based sandbox which also makes use of file descriptor retrieval.
The thread for this can be found at
https://sourceware.org/ml/libc-alpha/2019-12/msg00079.html
With pidfd_getfd() it is e.g. possible to bridge socket connections
for the supervisee (binding to a privileged port) and taking actions
on file descriptors on behalf of the supervisee in general.
Sargun's first version was using an ioctl on pidfds but various people
pushed for it to be a proper syscall which he duely implemented as
well over various review cycles. Selftests are of course included.
I've also added instructions how to deal with merge conflicts below.
There's also a small fix coming from the kernel mentee project to
correctly annotate struct sighand_struct with __rcu to fix various
sparse warnings. We've received a few more such fixes and even though
they are mostly trivial I've decided to postpone them until after -rc1
since they came in rather late and I don't want to risk introducing
build warnings.
Finally, there's a new prctl() command PR_{G,S}ET_IO_FLUSHER which is
needed to avoid allocation recursions triggerable by storage drivers
that have userspace parts that run in the IO path (e.g. dm-multipath,
iscsi, etc). These allocation recursions deadlock the device.
The new prctl() allows such privileged userspace components to avoid
allocation recursions by setting the PF_MEMALLOC_NOIO and
PF_LESS_THROTTLE flags. The patch carries the necessary acks from the
relevant maintainers and is routed here as part of prctl()
thread-management."
* tag 'threads-v5.6' of git://git.kernel.org/pub/scm/linux/kernel/git/brauner/linux:
prctl: PR_{G,S}ET_IO_FLUSHER to support controlling memory reclaim
sched.h: Annotate sighand_struct with __rcu
test: Add test for pidfd getfd
arch: wire up pidfd_getfd syscall
pid: Implement pidfd_getfd syscall
vfs, fdtable: Add fget_task helper
This series is slightly unusual because it includes Arnd's compat
ioctl tree here:
1c46a2cf2d Merge tag 'block-ioctl-cleanup-5.6' into 5.6/scsi-queue
Excluding Arnd's changes, this is mostly an update of the usual
drivers: megaraid_sas, mpt3sas, qla2xxx, ufs, lpfc, hisi_sas. There
are a couple of core and base updates around error propagation and
atomicity in the attribute container base we use for the SCSI
transport classes. The rest is minor changes and updates.
Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCXjHQJyYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishZZ8AQC02N+v
iUnTl1YxGPjIWBbnHuUxN2Qbb9D3C6gAT1LkigEArlk163K3A1XEQHF/VNCdAz/f
01XYTd3p1VHuegIBHlk=
=Cn52
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI updates from James Bottomley:
"This series is slightly unusual because it includes Arnd's compat
ioctl tree here:
1c46a2cf2d Merge tag 'block-ioctl-cleanup-5.6' into 5.6/scsi-queue
Excluding Arnd's changes, this is mostly an update of the usual
drivers: megaraid_sas, mpt3sas, qla2xxx, ufs, lpfc, hisi_sas.
There are a couple of core and base updates around error propagation
and atomicity in the attribute container base we use for the SCSI
transport classes.
The rest is minor changes and updates"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (149 commits)
scsi: hisi_sas: Rename hisi_sas_cq.pci_irq_mask
scsi: hisi_sas: Add prints for v3 hw interrupt converge and automatic affinity
scsi: hisi_sas: Modify the file permissions of trigger_dump to write only
scsi: hisi_sas: Replace magic number when handle channel interrupt
scsi: hisi_sas: replace spin_lock_irqsave/spin_unlock_restore with spin_lock/spin_unlock
scsi: hisi_sas: use threaded irq to process CQ interrupts
scsi: ufs: Use UFS device indicated maximum LU number
scsi: ufs: Add max_lu_supported in struct ufs_dev_info
scsi: ufs: Delete is_init_prefetch from struct ufs_hba
scsi: ufs: Inline two functions into their callers
scsi: ufs: Move ufshcd_get_max_pwr_mode() to ufshcd_device_params_init()
scsi: ufs: Split ufshcd_probe_hba() based on its called flow
scsi: ufs: Delete struct ufs_dev_desc
scsi: ufs: Fix ufshcd_probe_hba() reture value in case ufshcd_scsi_add_wlus() fails
scsi: ufs-mediatek: enable low-power mode for hibern8 state
scsi: ufs: export some functions for vendor usage
scsi: ufs-mediatek: add dbg_register_dump implementation
scsi: qla2xxx: Fix a NULL pointer dereference in an error path
scsi: qla1280: Make checking for 64bit support consistent
scsi: megaraid_sas: Update driver version to 07.713.01.00-rc1
...
Pull openat2 support from Al Viro:
"This is the openat2() series from Aleksa Sarai.
I'm afraid that the rest of namei stuff will have to wait - it got
zero review the last time I'd posted #work.namei, and there had been a
leak in the posted series I'd caught only last weekend. I was going to
repost it on Monday, but the window opened and the odds of getting any
review during that... Oh, well.
Anyway, openat2 part should be ready; that _did_ get sane amount of
review and public testing, so here it comes"
From Aleksa's description of the series:
"For a very long time, extending openat(2) with new features has been
incredibly frustrating. This stems from the fact that openat(2) is
possibly the most famous counter-example to the mantra "don't silently
accept garbage from userspace" -- it doesn't check whether unknown
flags are present[1].
This means that (generally) the addition of new flags to openat(2) has
been fraught with backwards-compatibility issues (O_TMPFILE has to be
defined as __O_TMPFILE|O_DIRECTORY|[O_RDWR or O_WRONLY] to ensure old
kernels gave errors, since it's insecure to silently ignore the
flag[2]). All new security-related flags therefore have a tough road
to being added to openat(2).
Furthermore, the need for some sort of control over VFS's path
resolution (to avoid malicious paths resulting in inadvertent
breakouts) has been a very long-standing desire of many userspace
applications.
This patchset is a revival of Al Viro's old AT_NO_JUMPS[3] patchset
(which was a variant of David Drysdale's O_BENEATH patchset[4] which
was a spin-off of the Capsicum project[5]) with a few additions and
changes made based on the previous discussion within [6] as well as
others I felt were useful.
In line with the conclusions of the original discussion of
AT_NO_JUMPS, the flag has been split up into separate flags. However,
instead of being an openat(2) flag it is provided through a new
syscall openat2(2) which provides several other improvements to the
openat(2) interface (see the patch description for more details). The
following new LOOKUP_* flags are added:
LOOKUP_NO_XDEV:
Blocks all mountpoint crossings (upwards, downwards, or through
absolute links). Absolute pathnames alone in openat(2) do not
trigger this. Magic-link traversal which implies a vfsmount jump is
also blocked (though magic-link jumps on the same vfsmount are
permitted).
LOOKUP_NO_MAGICLINKS:
Blocks resolution through /proc/$pid/fd-style links. This is done
by blocking the usage of nd_jump_link() during resolution in a
filesystem. The term "magic-links" is used to match with the only
reference to these links in Documentation/, but I'm happy to change
the name.
It should be noted that this is different to the scope of
~LOOKUP_FOLLOW in that it applies to all path components. However,
you can do openat2(NO_FOLLOW|NO_MAGICLINKS) on a magic-link and it
will *not* fail (assuming that no parent component was a
magic-link), and you will have an fd for the magic-link.
In order to correctly detect magic-links, the introduction of a new
LOOKUP_MAGICLINK_JUMPED state flag was required.
LOOKUP_BENEATH:
Disallows escapes to outside the starting dirfd's
tree, using techniques such as ".." or absolute links. Absolute
paths in openat(2) are also disallowed.
Conceptually this flag is to ensure you "stay below" a certain
point in the filesystem tree -- but this requires some additional
to protect against various races that would allow escape using
"..".
Currently LOOKUP_BENEATH implies LOOKUP_NO_MAGICLINKS, because it
can trivially beam you around the filesystem (breaking the
protection). In future, there might be similar safety checks done
as in LOOKUP_IN_ROOT, but that requires more discussion.
In addition, two new flags are added that expand on the above ideas:
LOOKUP_NO_SYMLINKS:
Does what it says on the tin. No symlink resolution is allowed at
all, including magic-links. Just as with LOOKUP_NO_MAGICLINKS this
can still be used with NOFOLLOW to open an fd for the symlink as
long as no parent path had a symlink component.
LOOKUP_IN_ROOT:
This is an extension of LOOKUP_BENEATH that, rather than blocking
attempts to move past the root, forces all such movements to be
scoped to the starting point. This provides chroot(2)-like
protection but without the cost of a chroot(2) for each filesystem
operation, as well as being safe against race attacks that
chroot(2) is not.
If a race is detected (as with LOOKUP_BENEATH) then an error is
generated, and similar to LOOKUP_BENEATH it is not permitted to
cross magic-links with LOOKUP_IN_ROOT.
The primary need for this is from container runtimes, which
currently need to do symlink scoping in userspace[7] when opening
paths in a potentially malicious container.
There is a long list of CVEs that could have bene mitigated by
having RESOLVE_THIS_ROOT (such as CVE-2017-1002101,
CVE-2017-1002102, CVE-2018-15664, and CVE-2019-5736, just to name a
few).
In order to make all of the above more usable, I'm working on
libpathrs[8] which is a C-friendly library for safe path resolution.
It features a userspace-emulated backend if the kernel doesn't support
openat2(2). Hopefully we can get userspace to switch to using it, and
thus get openat2(2) support for free once it's ready.
Future work would include implementing things like
RESOLVE_NO_AUTOMOUNT and possibly a RESOLVE_NO_REMOTE (to allow
programs to be sure they don't hit DoSes though stale NFS handles)"
* 'work.openat2' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
Documentation: path-lookup: include new LOOKUP flags
selftests: add openat2(2) selftests
open: introduce openat2(2) syscall
namei: LOOKUP_{IN_ROOT,BENEATH}: permit limited ".." resolution
namei: LOOKUP_IN_ROOT: chroot-like scoped resolution
namei: LOOKUP_BENEATH: O_BENEATH-like scoped resolution
namei: LOOKUP_NO_XDEV: block mountpoint crossing
namei: LOOKUP_NO_MAGICLINKS: block magic-link resolution
namei: LOOKUP_NO_SYMLINKS: block symlink resolution
namei: allow set_root() to produce errors
namei: allow nd_jump_link() to produce errors
nsfs: clean-up ns_get_path() signature to return int
namei: only return -ECHILD from follow_dotdot_rcu()
Here are the big set of tty and serial driver updates for 5.6-rc1
Included in here are:
- dummy_con cleanups (touches lots of arch code)
- sysrq logic cleanups (touches lots of serial drivers)
- samsung driver fixes (wasn't really being built)
- conmakeshash move to tty subdir out of scripts
- lots of small tty/serial driver updates
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXjFRBg8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+yn2VACgkge7vTeUNeZFc+6F4NWphAQ5tCQAoK/MMbU6
0O8ef7PjFwCU4s227UTv
=6m40
-----END PGP SIGNATURE-----
Merge tag 'tty-5.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial driver updates from Greg KH:
"Here are the big set of tty and serial driver updates for 5.6-rc1
Included in here are:
- dummy_con cleanups (touches lots of arch code)
- sysrq logic cleanups (touches lots of serial drivers)
- samsung driver fixes (wasn't really being built)
- conmakeshash move to tty subdir out of scripts
- lots of small tty/serial driver updates
All of these have been in linux-next for a while with no reported
issues"
* tag 'tty-5.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (140 commits)
tty: n_hdlc: Use flexible-array member and struct_size() helper
tty: baudrate: SPARC supports few more baud rates
tty: baudrate: Synchronise baud_table[] and baud_bits[]
tty: serial: meson_uart: Add support for kernel debugger
serial: imx: fix a race condition in receive path
serial: 8250_bcm2835aux: Document struct bcm2835aux_data
serial: 8250_bcm2835aux: Use generic remapping code
serial: 8250_bcm2835aux: Allocate uart_8250_port on stack
serial: 8250_bcm2835aux: Suppress register_port error on -EPROBE_DEFER
serial: 8250_bcm2835aux: Suppress clk_get error on -EPROBE_DEFER
serial: 8250_bcm2835aux: Fix line mismatch on driver unbind
serial_core: Remove unused member in uart_port
vt: Correct comment documenting do_take_over_console()
vt: Delete comment referencing non-existent unbind_con_driver()
arch/xtensa/setup: Drop dummy_con initialization
arch/x86/setup: Drop dummy_con initialization
arch/unicore32/setup: Drop dummy_con initialization
arch/sparc/setup: Drop dummy_con initialization
arch/sh/setup: Drop dummy_con initialization
arch/s390/setup: Drop dummy_con initialization
...
This doc patch provides an initial description of the hcall op-codes
that are used by Linux kernel running as a guest (LPAR) on top of
PowerVM or any other sPAPR compliant hyper-visor (e.g qemu).
Apart from documenting the hcalls the doc-patch also provides a
rudimentary overview of how hcall ABI, how they are issued with the
Linux kernel and how information/control flows between the guest and
hypervisor.
Signed-off-by: Vaibhav Jain <vaibhav@linux.ibm.com>
Reviewed-by: Laurent Dufour <ldufour@linux.ibm.com>
Acked-by: Nicholas Piggin <npiggin@gmail.com>
[mpe: Add SPDX tag, add it to index.rst]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20190828082729.16695-1-vaibhav@linux.ibm.com
Fixes: 3a167beac0 ("kvm: powerpc: Add kvmppc_ops callback")
Signed-off-by: David Michael <fedora.dm0@gmail.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
When migrate_vma_setup() fails in kvmppc_svm_page_out(),
release kvm->arch.uvmem_lock before returning.
Fixes: ca9f494267 ("KVM: PPC: Book3S HV: Support for running secure guests")
Signed-off-by: Bharata B Rao <bharata@linux.ibm.com>
Reviewed-by: Kamalesh Babulal <kamalesh@linux.vnet.ibm.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Pull crypto updates from Herbert Xu:
"API:
- Removed CRYPTO_TFM_RES flags
- Extended spawn grabbing to all algorithm types
- Moved hash descsize verification into API code
Algorithms:
- Fixed recursive pcrypt dead-lock
- Added new 32 and 64-bit generic versions of poly1305
- Added cryptogams implementation of x86/poly1305
Drivers:
- Added support for i.MX8M Mini in caam
- Added support for i.MX8M Nano in caam
- Added support for i.MX8M Plus in caam
- Added support for A33 variant of SS in sun4i-ss
- Added TEE support for Raven Ridge in ccp
- Added in-kernel API to submit TEE commands in ccp
- Added AMD-TEE driver
- Added support for BCM2711 in iproc-rng200
- Added support for AES256-GCM based ciphers for chtls
- Added aead support on SEC2 in hisilicon"
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6: (244 commits)
crypto: arm/chacha - fix build failured when kernel mode NEON is disabled
crypto: caam - add support for i.MX8M Plus
crypto: x86/poly1305 - emit does base conversion itself
crypto: hisilicon - fix spelling mistake "disgest" -> "digest"
crypto: chacha20poly1305 - add back missing test vectors and test chunking
crypto: x86/poly1305 - fix .gitignore typo
tee: fix memory allocation failure checks on drv_data and amdtee
crypto: ccree - erase unneeded inline funcs
crypto: ccree - make cc_pm_put_suspend() void
crypto: ccree - split overloaded usage of irq field
crypto: ccree - fix PM race condition
crypto: ccree - fix FDE descriptor sequence
crypto: ccree - cc_do_send_request() is void func
crypto: ccree - fix pm wrongful error reporting
crypto: ccree - turn errors to debug msgs
crypto: ccree - fix AEAD decrypt auth fail
crypto: ccree - fix typo in comment
crypto: ccree - fix typos in error msgs
crypto: atmel-{aes,sha,tdes} - Retire crypto_platform_data
crypto: x86/sha - Eliminate casts on asm implementations
...
Pull scheduler updates from Ingo Molnar:
"These were the main changes in this cycle:
- More -rt motivated separation of CONFIG_PREEMPT and
CONFIG_PREEMPTION.
- Add more low level scheduling topology sanity checks and warnings
to filter out nonsensical topologies that break scheduling.
- Extend uclamp constraints to influence wakeup CPU placement
- Make the RT scheduler more aware of asymmetric topologies and CPU
capacities, via uclamp metrics, if CONFIG_UCLAMP_TASK=y
- Make idle CPU selection more consistent
- Various fixes, smaller cleanups, updates and enhancements - please
see the git log for details"
* 'sched-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (58 commits)
sched/fair: Define sched_idle_cpu() only for SMP configurations
sched/topology: Assert non-NUMA topology masks don't (partially) overlap
idle: fix spelling mistake "iterrupts" -> "interrupts"
sched/fair: Remove redundant call to cpufreq_update_util()
sched/psi: create /proc/pressure and /proc/pressure/{io|memory|cpu} only when psi enabled
sched/fair: Fix sgc->{min,max}_capacity calculation for SD_OVERLAP
sched/fair: calculate delta runnable load only when it's needed
sched/cputime: move rq parameter in irqtime_account_process_tick
stop_machine: Make stop_cpus() static
sched/debug: Reset watchdog on all CPUs while processing sysrq-t
sched/core: Fix size of rq::uclamp initialization
sched/uclamp: Fix a bug in propagating uclamp value in new cgroups
sched/fair: Load balance aggressively for SCHED_IDLE CPUs
sched/fair : Improve update_sd_pick_busiest for spare capacity case
watchdog: Remove soft_lockup_hrtimer_cnt and related code
sched/rt: Make RT capacity-aware
sched/fair: Make EAS wakeup placement consider uclamp restrictions
sched/fair: Make task_fits_capacity() consider uclamp restrictions
sched/uclamp: Rename uclamp_util_with() into uclamp_rq_util_with()
sched/uclamp: Make uclamp util helpers use and return UL values
...
Pull EFI updates from Ingo Molnar:
"The main changes in this cycle were:
- Cleanup of the GOP [graphics output] handling code in the EFI stub
- Complete refactoring of the mixed mode handling in the x86 EFI stub
- Overhaul of the x86 EFI boot/runtime code
- Increase robustness for mixed mode code
- Add the ability to disable DMA at the root port level in the EFI
stub
- Get rid of RWX mappings in the EFI memory map and page tables,
where possible
- Move the support code for the old EFI memory mapping style into its
only user, the SGI UV1+ support code.
- plus misc fixes, updates, smaller cleanups.
... and due to interactions with the RWX changes, another round of PAT
cleanups make a guest appearance via the EFI tree - with no side
effects intended"
* 'efi-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (75 commits)
efi/x86: Disable instrumentation in the EFI runtime handling code
efi/libstub/x86: Fix EFI server boot failure
efi/x86: Disallow efi=old_map in mixed mode
x86/boot/compressed: Relax sed symbol type regex for LLVM ld.lld
efi/x86: avoid KASAN false positives when accessing the 1: 1 mapping
efi: Fix handling of multiple efi_fake_mem= entries
efi: Fix efi_memmap_alloc() leaks
efi: Add tracking for dynamically allocated memmaps
efi: Add a flags parameter to efi_memory_map
efi: Fix comment for efi_mem_type() wrt absent physical addresses
efi/arm: Defer probe of PCIe backed efifb on DT systems
efi/x86: Limit EFI old memory map to SGI UV machines
efi/x86: Avoid RWX mappings for all of DRAM
efi/x86: Don't map the entire kernel text RW for mixed mode
x86/mm: Fix NX bit clearing issue in kernel_map_pages_in_pgd
efi/libstub/x86: Fix unused-variable warning
efi/libstub/x86: Use mandatory 16-byte stack alignment in mixed mode
efi/libstub/x86: Use const attribute for efi_is_64bit()
efi: Allow disabling PCI busmastering on bridges during boot
efi/x86: Allow translating 64-bit arguments for mixed mode calls
...
Pull RCU updates from Ingo Molnar:
"The RCU changes in this cycle were:
- Expedited grace-period updates
- kfree_rcu() updates
- RCU list updates
- Preemptible RCU updates
- Torture-test updates
- Miscellaneous fixes
- Documentation updates"
* 'core-rcu-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (69 commits)
rcu: Remove unused stop-machine #include
powerpc: Remove comment about read_barrier_depends()
.mailmap: Add entries for old paulmck@kernel.org addresses
srcu: Apply *_ONCE() to ->srcu_last_gp_end
rcu: Switch force_qs_rnp() to for_each_leaf_node_cpu_mask()
rcu: Move rcu_{expedited,normal} definitions into rcupdate.h
rcu: Move gp_state_names[] and gp_state_getname() to tree_stall.h
rcu: Remove the declaration of call_rcu() in tree.h
rcu: Fix tracepoint tracking RCU CPU kthread utilization
rcu: Fix harmless omission of "CONFIG_" from #if condition
rcu: Avoid tick_dep_set_cpu() misordering
rcu: Provide wrappers for uses of ->rcu_read_lock_nesting
rcu: Use READ_ONCE() for ->expmask in rcu_read_unlock_special()
rcu: Clear ->rcu_read_unlock_special only once
rcu: Clear .exp_hint only when deferred quiescent state has been reported
rcu: Rename some instance of CONFIG_PREEMPTION to CONFIG_PREEMPT_RCU
rcu: Remove kfree_call_rcu_nobatch()
rcu: Remove kfree_rcu() special casing and lazy-callback handling
rcu: Add support for debug_objects debugging for kfree_rcu()
rcu: Add multiple in-flight batches of kfree_rcu() work
...
Pull objtool updates from Ingo Molnar:
"The main changes are to move the ORC unwind table sorting from early
init to build-time - this speeds up booting.
No change in functionality intended"
* 'core-objtool-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/unwind/orc: Fix !CONFIG_MODULES build warning
x86/unwind/orc: Remove boot-time ORC unwind tables sorting
scripts/sorttable: Implement build-time ORC unwind table sorting
scripts/sorttable: Rename 'sortextable' to 'sorttable'
scripts/sortextable: Refactor the do_func() function
scripts/sortextable: Remove dead code
scripts/sortextable: Clean up the code to meet the kernel coding style better
scripts/sortextable: Rewrite error/success handling
There's an OF helper called of_dma_is_coherent(), which checks if a
device has a "dma-coherent" property to see if the device is coherent
for DMA.
But on some platforms devices are coherent by default, and on some
platforms it's not possible to update existing device trees to add the
"dma-coherent" property.
So add a Kconfig symbol to allow arch code to tell
of_dma_is_coherent() that devices are coherent by default, regardless
of the presence of the property.
Select that symbol on powerpc when NOT_COHERENT_CACHE is not set, ie.
when the system has a coherent cache.
Fixes: 92ea637ede ("of: introduce of_dma_is_coherent() helper")
Cc: stable@vger.kernel.org # v3.16+
Reported-by: Christian Zigotzky <chzigotzky@xenosoft.de>
Tested-by: Christian Zigotzky <chzigotzky@xenosoft.de>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rob Herring <robh@kernel.org>
Implement user_access_save() and user_access_restore()
On 8xx and radix:
- On save, get the value of the associated special register then
prevent user access.
- On restore, set back the saved value to the associated special
register.
On book3s/32:
- On save, get the value stored in current->thread.kuap and prevent
user access.
- On restore, regenerate address range from the stored value and
reopen read/write access for that range.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/54f2f74938006b33c55a416674807b42ef222068.1579866752.git.christophe.leroy@c-s.fr
Today, when a function like strncpy_from_user() is called,
the userspace access protection is de-activated and re-activated
for every word read.
By implementing user_access_begin and friends, the protection
is de-activated at the beginning of the copy and re-activated at the
end.
Implement user_access_begin(), user_access_end() and
unsafe_get_user(), unsafe_put_user() and unsafe_copy_to_user()
For the time being, we keep user_access_save() and
user_access_restore() as nops.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/36d4fbf9e56a75994aca4ee2214c77b26a5a8d35.1579866752.git.christophe.leroy@c-s.fr
In preparation of implementing user_access_begin and friends
on powerpc, the book3s/32 version of prevent_user_access() need
to be prepared for user_access_end().
user_access_end() doesn't provide the address and size which
were passed to user_access_begin(), required by prevent_user_access()
to know which segment to modify.
The list of segments which where unprotected by allow_user_access()
are available in current->kuap. But we don't want prevent_user_access()
to read this all the time, especially everytime it is 0 (for instance
because the access was not a write access).
Implement a special direction named KUAP_CURRENT. In this case only,
the addr and end are retrieved from current->kuap.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/55bcc1f25d8200892a31f67a0b024ff3b816c3cc.1579866752.git.christophe.leroy@c-s.fr
NULL addr is a user address. Don't waste time checking it. If
someone tries to access it, it will SIGFAULT the same way as for
address 1, so no need to make it special.
The special case is when not doing a write, in that case we want
to drop the entire function. This is now handled by 'dir' param
and not by the nulity of 'to' anymore.
Also make beginning of prevent_user_access() similar
to beginning of allow_user_access(), and tell the compiler
that writing in kernel space or with a 0 length is unlikely
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/85e971223dfe6ace734637db1841678939a76155.1579866752.git.christophe.leroy@c-s.fr
At the moment, bad_kuap_fault() reports a fault only if a bad access
to userspace occurred while access to userspace was not granted.
But if a fault occurs for a write outside the allowed userspace
segment(s) that have been unlocked, bad_kuap_fault() fails to
detect it and the kernel loops forever in do_page_fault().
Fix it by checking that the accessed address is within the allowed
range.
Fixes: a68c31fc01 ("powerpc/32s: Implement Kernel Userspace Access Protection")
Cc: stable@vger.kernel.org # v5.2+
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/f48244e9485ada0a304ed33ccbb8da271180c80d.1579866752.git.christophe.leroy@c-s.fr
Commit f7354ccac8 ("powerpc/32: Remove CURRENT_THREAD_INFO and
rename TI_CPU") broke the CPU wake-up from sleep mode (i.e. when
_TLF_SLEEPING is set) by delaying the tovirt(r2, r2).
This is because r2 is not restored by fast_exception_return. It used
to work (by chance ?) because CPU wake-up interrupt never comes from
user, so r2 is expected to point to 'current' on return.
Commit e2fb9f5444 ("powerpc/32: Prepare for Kernel Userspace Access
Protection") broke it even more by clobbering r0 which is not
restored by fast_exception_return either.
Use r6 instead of r0. This is possible because r3-r6 are restored by
fast_exception_return and only r3-r5 are used for exception arguments.
For r2 it could be converted back to virtual address, but stay on the
safe side and restore it from the stack instead. It should be live
in the cache at that moment, so loading from the stack should make
no difference compared to converting it from phys to virt.
Fixes: f7354ccac8 ("powerpc/32: Remove CURRENT_THREAD_INFO and rename TI_CPU")
Fixes: e2fb9f5444 ("powerpc/32: Prepare for Kernel Userspace Access Protection")
Cc: stable@vger.kernel.org
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/6d02c3ae6ad77af34392e98117e44c2bf6d13ba1.1580121710.git.christophe.leroy@c-s.fr
- remove ioremap_nocache given that is is equivalent to
ioremap everywhere
-----BEGIN PGP SIGNATURE-----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=TUCJ
-----END PGP SIGNATURE-----
Merge tag 'ioremap-5.6' of git://git.infradead.org/users/hch/ioremap
Pull ioremap updates from Christoph Hellwig:
"Remove the ioremap_nocache API (plus wrappers) that are always
identical to ioremap"
* tag 'ioremap-5.6' of git://git.infradead.org/users/hch/ioremap:
remove ioremap_nocache and devm_ioremap_nocache
MIPS: define ioremap_nocache to ioremap
Use kvm_vcpu_gfn_to_hva() when retrieving the host page size so that the
correct set of memslots is used when handling x86 page faults in SMM.
Fixes: 54bf36aac5 ("KVM: x86: use vcpu-specific functions to read/write/translate GFNs")
Cc: stable@vger.kernel.org
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Remove kvm_arch_vcpu_init() and kvm_arch_vcpu_uninit() now that all
arch specific implementations are nops.
Acked-by: Christoffer Dall <christoffer.dall@arm.com>
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Fold init() into create() now that the two are called back-to-back by
common KVM code (kvm_vcpu_init() calls kvm_arch_vcpu_init() as its last
action, and kvm_vm_ioctl_create_vcpu() calls kvm_arch_vcpu_create()
immediately thereafter). Rinse and repeat for kvm_arch_vcpu_uninit()
and kvm_arch_vcpu_destroy(). This paves the way for removing
kvm_arch_vcpu_{un}init() entirely.
Note, calling kvmppc_mmu_destroy() if kvmppc_core_vcpu_create() fails
may or may not be necessary. Move it along with the more obvious call
to kvmppc_subarch_vcpu_uninit() so as not to inadvertantly introduce a
functional change and/or bug.
No functional change intended.
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Remove kvm_arch_vcpu_setup() now that all arch specific implementations
are nops.
Acked-by: Christoffer Dall <christoffer.dall@arm.com>
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Fold setup() into create() now that the two are called back-to-back by
common KVM code. This paves the way for removing kvm_arch_vcpu_setup().
Note, BookE directly implements kvm_arch_vcpu_setup() and PPC's common
kvm_arch_vcpu_create() is responsible for its own cleanup, thus the only
cleanup required when directly invoking kvmppc_core_vcpu_setup() is to
call .vcpu_free(), which is the BookE specific portion of PPC's
kvm_arch_vcpu_destroy() by way of kvmppc_core_vcpu_free().
No functional change intended.
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Now that all architectures tightly couple vcpu allocation/free with the
mandatory calls to kvm_{un}init_vcpu(), move the sequences verbatim to
common KVM code.
Move both allocation and initialization in a single patch to eliminate
thrash in arch specific code. The bisection benefits of moving the two
pieces in separate patches is marginal at best, whereas the odds of
introducing a transient arch specific bug are non-zero.
Acked-by: Christoffer Dall <christoffer.dall@arm.com>
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Add support of KASAN_VMALLOC on PPC32.
To allow this, the early shadow covering the VMALLOC space
need to be removed once high_memory var is set and before
freeing memblock.
And the VMALLOC area need to be aligned such that boundaries
are covered by a full shadow page.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/031dec5487bde9b2181c8b3c9800e1879cf98c1a.1579024426.git.christophe.leroy@c-s.fr
Running vdsotest leaves many times the following log:
[ 79.629901] vdsotest[396]: User access of kernel address (ffffffff) - exploit attempt? (uid: 0)
A pointer set to (-1) is likely a programming error similar to
a NULL pointer and is not worth logging as an exploit attempt.
Don't log user accesses to 0xffffffff.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/0728849e826ba16f1fbd6fa7f5c6cc87bd64e097.1577087627.git.christophe.leroy@c-s.fr
A few changes to retrieve DAR and DSISR from struct regs
instead of retrieving them directly, as they may have
changed due to a TLB miss.
Also modifies hash_page() and friends to work with virtual
data addresses instead of physical ones. Same on load_up_fpu()
and load_up_altivec().
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
[mpe: Fix tovirt_vmstack call in head_32.S to fix CHRP build]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/2e2509a242fd5f3e23df4a06530c18060c4d321e.1576916812.git.christophe.leroy@c-s.fr
Trying VMAP_STACK with KVM, vmlinux was not starting.
This was due to SRR0 and SRR1 clobbered by an ISI due to
the rfi being in a different page than the mtsrr0/1:
c0003fe0 <mmu_off>:
c0003fe0: 38 83 00 54 addi r4,r3,84
c0003fe4: 7c 60 00 a6 mfmsr r3
c0003fe8: 70 60 00 30 andi. r0,r3,48
c0003fec: 4d 82 00 20 beqlr
c0003ff0: 7c 63 00 78 andc r3,r3,r0
c0003ff4: 7c 9a 03 a6 mtsrr0 r4
c0003ff8: 7c 7b 03 a6 mtsrr1 r3
c0003ffc: 7c 00 04 ac hwsync
c0004000: 4c 00 00 64 rfi
Align the 4 instruction block used to deactivate MMU to order 4,
so that the block never crosses a page boundary.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/30d2cda111b7977227fff067fa7e358440e2b3a4.1576916812.git.christophe.leroy@c-s.fr
The part decidated to handling hash_page() is fully unneeded for
processors not having real hash pages like the 603.
Lets enlarge the content of the feature fixup, and provide
an alternative which jumps directly instead of getting NIPs.
Also, in preparation of VMAP stacks, the end of DSI handler has moved
to later in the code as it won't fit anymore once VMAP stacks
are there.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/c31b22c91af8b011d0a4fd9e52ad6afb4b593f71.1576916812.git.christophe.leroy@c-s.fr
When we enable VMAP_STACK there will not be enough room for the
alignment handler at 0x600 in head_8xx.S. For now move the tail of the
alignment handler out of line, and branch to it.
Suggested-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
head_8xx.S has entries for all exceptions from 0x100 to 0x1f00.
Several of them do not exist and are never generated by the 8xx
in accordance with the documentation.
Remove those entry points to make some room for future growing
exception code.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/66f92866fe9524cf0f056016921c7d53adaef3a0.1576916812.git.christophe.leroy@c-s.fr
In preparation of handling CONFIG_VMAP_STACK, DTLB miss handler need
to use different scratch registers than other exception handlers in
order to not jeopardise exception entry on stack DTLB misses.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/c5287ea59ae9630f505019b309bf94029241635f.1576916812.git.christophe.leroy@c-s.fr
