Before commit 780db2071a(blk-mq: decouble blk-mq freezing
from generic bypassing), the dying flag is checked before
entering queue, and Tejun converts the checking into .mq_freeze_depth,
and assumes the counter is increased just after dying flag
is set. Unfortunately we doesn't do that in blk_set_queue_dying().
This patch calls blk_freeze_queue_start() in blk_set_queue_dying(),
so that we can block new I/O coming once the queue is set as dying.
Given blk_set_queue_dying() is always called in remove path
of block device, and queue will be cleaned up later, we don't
need to worry about undoing the counter.
Cc: Tejun Heo <tj@kernel.org>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Bart Van Assche <bart.vanassche@sandisk.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
As the .q_usage_counter is used by both legacy and
mq path, we need to block new I/O if queue becomes
dead in blk_queue_enter().
So rename it and we can use this function in both
paths.
Reviewed-by: Bart Van Assche <bart.vanassche@sandisk.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
Without the barrier, reading DEAD flag of .q_usage_counter
and reading .mq_freeze_depth may be reordered, then the
following wait_event_interruptible() may never return.
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Bart Van Assche <bart.vanassche@sandisk.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
This patch adds comment on two races related with
timeout handler:
- requeue from queue busy vs. timeout
- rq free & reallocation vs. timeout
Both the races themselves and current solution aren't
explicit enough, so add comments on them.
Cc: Bart Van Assche <bart.vanassche@sandisk.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
blkg_conf_prep() currently calls blkg_lookup_create() while holding
request queue spinlock. This means allocating memory for struct
blkcg_gq has to be made non-blocking. This causes occasional -ENOMEM
failures in call paths like below:
pcpu_alloc+0x68f/0x710
__alloc_percpu_gfp+0xd/0x10
__percpu_counter_init+0x55/0xc0
cfq_pd_alloc+0x3b2/0x4e0
blkg_alloc+0x187/0x230
blkg_create+0x489/0x670
blkg_lookup_create+0x9a/0x230
blkg_conf_prep+0x1fb/0x240
__cfqg_set_weight_device.isra.105+0x5c/0x180
cfq_set_weight_on_dfl+0x69/0xc0
cgroup_file_write+0x39/0x1c0
kernfs_fop_write+0x13f/0x1d0
__vfs_write+0x23/0x120
vfs_write+0xc2/0x1f0
SyS_write+0x44/0xb0
entry_SYSCALL_64_fastpath+0x18/0xad
In the code path above, percpu allocator cannot call vmalloc() due to
queue spinlock.
A failure in this call path gives grief to tools which are trying to
configure io weights. We see occasional failures happen shortly after
reboots even when system is not under any memory pressure. Machines
with a lot of cpus are more vulnerable to this condition.
Update blkg_create() function to temporarily drop the rcu and queue
locks when it is allowed by gfp mask.
Suggested-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Tahsin Erdogan <tahsin@google.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jens Axboe <axboe@fb.com>
Compile-tested only (by hacking it to compile on x86).
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Omar Sandoval <osandov@fb.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Fixes to multiple issues in virtio. Most notably
a regression fix for crashes reported by Fedora users.
Hybernate is still reportedly broken, working on it.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJY2qEcAAoJECgfDbjSjVRpM/oH/3GPZOh9/tMzDFDaDljqtWQy
PGVb74/3+O55xOOq9nyyS3+6BlCXmiUcynxg61QUOUqUuHPPdH/OntyyPgG0pYkx
271W81C1yc2xFp/qkOiMWKiPmsbJ7ykVg37NWtxm7Phf4RgX3wgymq87hWr4Td1G
q9k6oyMCmvJUECJVxOVHjPt+oYQ7zQkFBNB8kSNlj67gbe533jkPt46MMlXbX7fQ
lPdJTnLXN/GQxnVtw5AAiWF87z0wNVUefrLe9sHW3KOeGBdne4NXblvz3WF/iPq4
N96thgm7QOP3NgAqbaUa7Fb0+jxyi2DNYFrVPxnf+nOOQy/AVUX6GRZJ2Tu6gF0=
=oSO5
-----END PGP SIGNATURE-----
Merge tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost
Pull virtio fixes from Michael Tsirkin:
"Fixes to multiple issues in virtio.
Most notably a regression fix for crashes reported by Fedora users.
Hibernate is still reportedly broken, working on it"
* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost:
virtio_balloon: prevent uninitialized variable use
virtio-balloon: use actual number of stats for stats queue buffers
virtio_balloon: init 1st buffer in stats vq
virtio_pci: fix out of bound access for msix_names
The latest gcc-7.0.1 snapshot reports a new warning:
virtio/virtio_balloon.c: In function 'update_balloon_stats':
virtio/virtio_balloon.c:258:26: error: 'events[2]' is used uninitialized in this function [-Werror=uninitialized]
virtio/virtio_balloon.c:260:26: error: 'events[3]' is used uninitialized in this function [-Werror=uninitialized]
virtio/virtio_balloon.c:261:56: error: 'events[18]' is used uninitialized in this function [-Werror=uninitialized]
virtio/virtio_balloon.c:262:56: error: 'events[17]' is used uninitialized in this function [-Werror=uninitialized]
This seems absolutely right, so we should add an extra check to
prevent copying uninitialized stack data into the statistics.
>From all I can tell, this has been broken since the statistics code
was originally added in 2.6.34.
Fixes: 9564e138b1 ("virtio: Add memory statistics reporting to the balloon driver (V4)")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Ladi Prosek <lprosek@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The virtio balloon driver contained a not-so-obvious invariant that
update_balloon_stats has to update exactly VIRTIO_BALLOON_S_NR counters
in order to send valid stats to the host. This commit fixes it by having
update_balloon_stats return the actual number of counters, and its
callers use it when pushing buffers to the stats virtqueue.
Note that it is still out of spec to change the number of counters
at run-time. "Driver MUST supply the same subset of statistics in all
buffers submitted to the statsq."
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Ladi Prosek <lprosek@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
When init_vqs runs, virtio_balloon.stats is either uninitialized or
contains stale values. The host updates its state with garbage data
because it has no way of knowing that this is just a marker buffer
used for signaling.
This patch updates the stats before pushing the initial buffer.
Alternative fixes:
* Push an empty buffer in init_vqs. Not easily done with the current
virtio implementation and violates the spec "Driver MUST supply the
same subset of statistics in all buffers submitted to the statsq".
* Push a buffer with invalid tags in init_vqs. Violates the same
spec clause, plus "invalid tag" is not really defined.
Note: the spec says:
When using the legacy interface, the device SHOULD ignore all values in
the first buffer in the statsq supplied by the driver after device
initialization. Note: Historically, drivers supplied an uninitialized
buffer in the first buffer.
Unfortunately QEMU does not seem to implement the recommendation
even for the legacy interface.
Cc: stable@vger.kernel.org
Signed-off-by: Ladi Prosek <lprosek@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Fedora has received multiple reports of crashes when running
4.11 as a guest
https://bugzilla.redhat.com/show_bug.cgi?id=1430297https://bugzilla.redhat.com/show_bug.cgi?id=1434462https://bugzilla.kernel.org/show_bug.cgi?id=194911https://bugzilla.redhat.com/show_bug.cgi?id=1433899
The crashes are not always consistent but they are generally
some flavor of oops or GPF in virtio related code. Multiple people
have done bisections (Thank you Thorsten Leemhuis and
Richard W.M. Jones) and found this commit to be at fault
07ec51480b is the first bad commit
commit 07ec51480b
Author: Christoph Hellwig <hch@lst.de>
Date: Sun Feb 5 18:15:19 2017 +0100
virtio_pci: use shared interrupts for virtqueues
The issue seems to be an out of bounds access to the msix_names
array corrupting kernel memory.
Fixes: 07ec51480b ("virtio_pci: use shared interrupts for virtqueues")
Reported-by: Laura Abbott <labbott@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Tested-by: Richard W.M. Jones <rjones@redhat.com>
Tested-by: Thorsten Leemhuis <linux@leemhuis.info>
One hard problem adding .low limit is to detect idle cgroup. If one
cgroup doesn't dispatch enough IO against its low limit, we must have a
mechanism to determine if other cgroups dispatch more IO. We added the
think time detection mechanism before, but it doesn't work for all
workloads. Here we add a latency based approach.
We already have mechanism to calculate latency threshold for each IO
size. For every IO dispatched from a cgorup, we compare its latency
against its threshold and record the info. If most IO latency is below
threshold (in the code I use 75%), the cgroup could be treated idle and
other cgroups can dispatch more IO.
Currently this latency target check is only for SSD as we can't
calcualte the latency target for hard disk. And this is only for cgroup
leaf node so far.
Signed-off-by: Shaohua Li <shli@fb.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
User configures latency target, but the latency threshold for each
request size isn't fixed. For a SSD, the IO latency highly depends on
request size. To calculate latency threshold, we sample some data, eg,
average latency for request size 4k, 8k, 16k, 32k .. 1M. The latency
threshold of each request size will be the sample latency (I'll call it
base latency) plus latency target. For example, the base latency for
request size 4k is 80us and user configures latency target 60us. The 4k
latency threshold will be 80 + 60 = 140us.
To sample data, we calculate the order base 2 of rounded up IO sectors.
If the IO size is bigger than 1M, it will be accounted as 1M. Since the
calculation does round up, the base latency will be slightly smaller
than actual value. Also if there isn't any IO dispatched for a specific
IO size, we will use the base latency of smaller IO size for this IO
size.
But we shouldn't sample data at any time. The base latency is supposed
to be latency where disk isn't congested, because we use latency
threshold to schedule IOs between cgroups. If disk is congested, the
latency is higher, using it for scheduling is meaningless. Hence we only
do the sampling when block throttling is in the LOW limit, with
assumption disk isn't congested in such state. If the assumption isn't
true, eg, low limit is too high, calculated latency threshold will be
higher.
Hard disk is completely different. Latency depends on spindle seek
instead of request size. Currently this feature is SSD only, we probably
can use a fixed threshold like 4ms for hard disk though.
Signed-off-by: Shaohua Li <shli@fb.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Currently there is no way to know the request size when the request is
finished. Next patch will need this info. We could add extra field to
record the size, but blk_issue_stat has enough space to record it, so
this patch just overloads blk_issue_stat. With this, we will have 49bits
to track time, which still is very long time.
Signed-off-by: Shaohua Li <shli@fb.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Here we introduce per-cgroup latency target. The target determines how a
cgroup can afford latency increasement. We will use the target latency
to calculate a threshold and use it to schedule IO for cgroups. If a
cgroup's bandwidth is below its low limit but its average latency is
below the threshold, other cgroups can safely dispatch more IO even
their bandwidth is higher than their low limits. On the other hand, if
the first cgroup's latency is higher than the threshold, other cgroups
are throttled to their low limits. So the target latency determines how
we efficiently utilize free disk resource without sacifice of worload's
IO latency.
For example, assume 4k IO average latency is 50us when disk isn't
congested. A cgroup sets the target latency to 30us. Then the cgroup can
accept 50+30=80us IO latency. If the cgroupt's average IO latency is
90us and its bandwidth is below low limit, other cgroups are throttled
to their low limit. If the cgroup's average IO latency is 60us, other
cgroups are allowed to dispatch more IO. When other cgroups dispatch
more IO, the first cgroup's IO latency will increase. If it increases to
81us, we then throttle other cgroups.
User will configure the interface in this way:
echo "8:16 rbps=2097152 wbps=max latency=100 idle=200" > io.low
latency is in microsecond unit
By default, latency target is 0, which means to guarantee IO latency.
Signed-off-by: Shaohua Li <shli@fb.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Last patch introduces a way to detect idle cgroup. We use it to make
upgrade/downgrade decision. And the new algorithm can detect completely
idle cgroup too, so we can delete the corresponding code.
Signed-off-by: Shaohua Li <shli@fb.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Add interface to configure the threshold. The io.low interface will
like:
echo "8:16 rbps=2097152 wbps=max idle=2000" > io.low
idle is in microsecond unit.
Signed-off-by: Shaohua Li <shli@fb.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
A cgroup gets assigned a low limit, but the cgroup could never dispatch
enough IO to cross the low limit. In such case, the queue state machine
will remain in LIMIT_LOW state and all other cgroups will be throttled
according to low limit. This is unfair for other cgroups. We should
treat the cgroup idle and upgrade the state machine to lower state.
We also have a downgrade logic. If the state machine upgrades because of
cgroup idle (real idle), the state machine will downgrade soon as the
cgroup is below its low limit. This isn't what we want. A more
complicated case is cgroup isn't idle when queue is in LIMIT_LOW. But
when queue gets upgraded to lower state, other cgroups could dispatch
more IO and this cgroup can't dispatch enough IO, so the cgroup is below
its low limit and looks like idle (fake idle). In this case, the queue
should downgrade soon. The key to determine if we should do downgrade is
to detect if cgroup is truely idle.
Unfortunately it's very hard to determine if a cgroup is real idle. This
patch uses the 'think time check' idea from CFQ for the purpose. Please
note, the idea doesn't work for all workloads. For example, a workload
with io depth 8 has disk utilization 100%, hence think time is 0, eg,
not idle. But the workload can run higher bandwidth with io depth 16.
Compared to io depth 16, the io depth 8 workload is idle. We use the
idea to roughly determine if a cgroup is idle.
We treat a cgroup idle if its think time is above a threshold (by
default 1ms for SSD and 100ms for HD). The idea is think time above the
threshold will start to harm performance. HD is much slower so a longer
think time is ok.
The patch (and the latter patches) uses 'unsigned long' to track time.
We convert 'ns' to 'us' with 'ns >> 10'. This is fast but loses
precision, should not a big deal.
Signed-off-by: Shaohua Li <shli@fb.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
When cgroups all reach low limit, cgroups can dispatch more IO. This
could make some cgroups dispatch more IO but others not, and even some
cgroups could dispatch less IO than their low limit. For example, cg1
low limit 10MB/s, cg2 limit 80MB/s, assume disk maximum bandwidth is
120M/s for the workload. Their bps could something like this:
cg1/cg2 bps: T1: 10/80 -> T2: 60/60 -> T3: 10/80
At T1, all cgroups reach low limit, so they can dispatch more IO later.
Then cg1 dispatch more IO and cg2 has no room to dispatch enough IO. At
T2, cg2 only dispatches 60M/s. Since We detect cg2 dispatches less IO
than its low limit 80M/s, we downgrade the queue from LIMIT_MAX to
LIMIT_LOW, then all cgroups are throttled to their low limit (T3). cg2
will have bandwidth below its low limit at most time.
The big problem here is we don't know the maximum bandwidth of the
workload, so we can't make smart decision to avoid the situation. This
patch makes cgroup bandwidth change smooth. After disk upgrades from
LIMIT_LOW to LIMIT_MAX, we don't allow cgroups use all bandwidth upto
their max limit immediately. Their bandwidth limit will be increased
gradually to avoid above situation. So above example will became
something like:
cg1/cg2 bps: 10/80 -> 15/105 -> 20/100 -> 25/95 -> 30/90 -> 35/85 -> 40/80
-> 45/75 -> 22/98
In this way cgroups bandwidth will be above their limit in majority
time, this still doesn't fully utilize disk bandwidth, but that's
something we pay for sharing.
Scale up is linear. The limit scales up 1/2 .low limit every
throtl_slice after upgrade. The scale up will stop if the adjusted limit
hits .max limit. Scale down is exponential. We cut the scale value half
if a cgroup doesn't hit its .low limit. If the scale becomes 0, we then
fully downgrade the queue to LIMIT_LOW state.
Note this doesn't completely avoid cgroup running under its low limit.
The best way to guarantee cgroup doesn't run under its limit is to set
max limit. For example, if we set cg1 max limit to 40, cg2 will never
run under its low limit.
Signed-off-by: Shaohua Li <shli@fb.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
cgroup could be assigned a limit, but doesn't dispatch enough IO, eg the
cgroup is idle. When this happens, the cgroup doesn't hit its limit, so
we can't move the state machine to higher level and all cgroups will be
throttled to their lower limit, so we waste bandwidth. Detecting idle
cgroup is hard. This patch handles a simple case, a cgroup doesn't
dispatch any IO. We ignore such cgroup's limit, so other cgroups can use
the bandwidth.
Please note this will be replaced with a more sophisticated algorithm
later, but this demonstrates the idea how we handle idle cgroups, so I
leave it here.
Signed-off-by: Shaohua Li <shli@fb.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
The throtl_slice is 100ms by default. This is a long time for SSD, a lot
of IO can run. To make cgroups have smoother throughput, we choose a
small value (20ms) for SSD.
Signed-off-by: Shaohua Li <shli@fb.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
throtl_slice is important for blk-throttling. It's called slice
internally but it really is a time window blk-throttling samples data.
blk-throttling will make decision based on the samplings. An example is
bandwidth measurement. A cgroup's bandwidth is measured in the time
interval of throtl_slice.
A small throtl_slice meanse cgroups have smoother throughput but burn
more CPUs. It has 100ms default value, which is not appropriate for all
disks. A fast SSD can dispatch a lot of IOs in 100ms. This patch makes
it tunable.
Since throtl_slice isn't a time slice, the sysfs name
'throttle_sample_time' reflects its character better.
Signed-off-by: Shaohua Li <shli@fb.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
cgroup could be throttled to a limit but when all cgroups cross high
limit, queue enters a higher state and so the group should be throttled
to a higher limit. It's possible the cgroup is sleeping because of
throttle and other cgroups don't dispatch IO any more. In this case,
nobody can trigger current downgrade/upgrade logic. To fix this issue,
we could either set up a timer to wakeup the cgroup if other cgroups are
idle or make sure this cgroup doesn't sleep too long. Setting up a timer
means we must change the timer very frequently. This patch chooses the
latter. Making cgroup sleep time not too big wouldn't change cgroup
bps/iops, but could make it wakeup more frequently, which isn't a big
issue because throtl_slice * 8 is already quite big.
Signed-off-by: Shaohua Li <shli@fb.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
When queue state machine is in LIMIT_MAX state, but a cgroup is below
its low limit for some time, the queue should be downgraded to lower
state as one cgroup's low limit isn't met.
Signed-off-by: Shaohua Li <shli@fb.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
When queue is in LIMIT_LOW state and all cgroups with low limit cross
the bps/iops limitation, we will upgrade queue's state to
LIMIT_MAX. To determine if a cgroup exceeds its limitation, we check if
the cgroup has pending request. Since cgroup is throttled according to
the limit, pending request means the cgroup reaches the limit.
If a cgroup has limit set for both read and write, we consider the
combination of them for upgrade. The reason is read IO and write IO can
interfere with each other. If we do the upgrade based in one direction
IO, the other direction IO could be severly harmed.
For a cgroup hierarchy, there are two cases. Children has lower low
limit than parent. Parent's low limit is meaningless. If children's
bps/iops cross low limit, we can upgrade queue state. The other case is
children has higher low limit than parent. Children's low limit is
meaningless. As long as parent's bps/iops (which is a sum of childrens
bps/iops) cross low limit, we can upgrade queue state.
Signed-off-by: Shaohua Li <shli@fb.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
each queue will have a state machine. Initially queue is in LIMIT_LOW
state, which means all cgroups will be throttled according to their low
limit. After all cgroups with low limit cross the limit, the queue state
gets upgraded to LIMIT_MAX state.
For max limit, cgroup will use the limit configured by user.
For low limit, cgroup will use the minimal value between low limit and
max limit configured by user. If the minimal value is 0, which means the
cgroup doesn't configure low limit, we will use max limit to throttle
the cgroup and the cgroup is ready to upgrade to LIMIT_MAX
Signed-off-by: Shaohua Li <shli@fb.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Add low limit for cgroup and corresponding cgroup interface. To be
consistent with memcg, we allow users configure .low limit higher than
.max limit. But the internal logic always assumes .low limit is lower
than .max limit. So we add extra bps/iops_conf fields in throtl_grp for
userspace configuration. Old bps/iops fields in throtl_grp will be the
actual limit we use for throttling.
Signed-off-by: Shaohua Li <shli@fb.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
As discussed in LSF, add configure option for the interface and mark it
as experimental, so people can try/test.
Signed-off-by: Shaohua Li <shli@fb.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
We are going to support low/max limit, each cgroup will have 2 limits
after that. This patch prepares for the multiple limits change.
Signed-off-by: Shaohua Li <shli@fb.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
SRCU uses a delayed work item. Skip cleaning it up, and
the result is use-after-free in the work item callbacks.
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Suggested-by: Dmitry Vyukov <dvyukov@google.com>
Cc: stable@vger.kernel.org
Fixes: 0eb05bf290
Reviewed-by: Xiao Guangrong <xiaoguangrong.eric@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The nested_ept_enabled flag introduced in commit 7ca29de213 was not
computed correctly. We are interested only in L1's EPT state, not the
the combined L0+L1 value.
In particular, if L0 uses EPT but L1 does not, nested_ept_enabled must
be false to make sure that PDPSTRs are loaded based on CR3 as usual,
because the special case described in 26.3.2.4 Loading Page-Directory-
Pointer-Table Entries does not apply.
Fixes: 7ca29de213 ("KVM: nVMX: fix CR3 load if L2 uses PAE paging and EPT")
Cc: qemu-stable@nongnu.org
Reported-by: Wanpeng Li <wanpeng.li@hotmail.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Signed-off-by: Ladi Prosek <lprosek@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
or VM memory are not put thus leaked in kvm_iommu_unmap_memslots() when
destroy VM.
This is consistent with current vfio implementation.
Signed-off-by: herongguang <herongguang.he@huawei.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Intel Apollo Lake platform and the Denverton microserver.
+ small fixlets.
-----BEGIN PGP SIGNATURE-----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=aftN
-----END PGP SIGNATURE-----
Merge tag 'edac_for_4.11_2' of git://git.kernel.org/pub/scm/linux/kernel/git/bp/bp
Pull EDAC updates from Borislav Petkov:
"A new EDAC driver for the Pondicherry2 memory controller IP found in
the Intel Apollo Lake platform and the Denverton microserver.
Plus small fixlets.
Normally I had this queued for 4.12 but Tony requested for the
pnd2_edac driver to possibly land in 4.11 therefore I'm sending it to
you now.
It is a driver for new hardware which people don't have yet so it
shouldn't cause any regressions.
The couple of patches ontop of it show that Qiuxu actually did test it
on the hardware he has access to :)"
* tag 'edac_for_4.11_2' of git://git.kernel.org/pub/scm/linux/kernel/git/bp/bp:
EDAC, pnd2_edac: Fix reported DIMM number
EDAC, pnd2_edac: Fix !EDAC_DEBUG build
EDAC: Select DEBUG_FS
EDAC, pnd2_edac: Add new EDAC driver for Intel SoC platforms
EDAC, i5000, i5400: Fix use of MTR_DRAM_WIDTH macro
EDAC, xgene: Fix wrongly spelled "procesing"
- Kconfig fixup for the TI IOdelay pinctrl-single add-on.
- Fix up a typo in the meson i2c ao groups.
- Switch a remapping back to use devm_ioremap() as
devm_ioremap_resource() does not allow for sharing memory
regions.
- Do not clear the Qualcomm irq status bit in irq_unmask(),
as this can lead to missing interrupts while the irq handler
is executing.
- Add irq_request/release_resources() on the ST driver.
- Add a bunch of mysteriously missing pingroups for high
numbered pins in the Qualcomm ipq4019 driver.
-----BEGIN PGP SIGNATURE-----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=0sa2
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-v4.11-3' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull more pin control fixes from Linus Walleij:
"Here is a bunch of pin control fixes again
A bit more than I'd like for this subsystem at this point, but what
can I do. They are all driver fixes for hardware issues, as like "we
forgot", "we didn't think of the fact that this could happen", "oops
that one goes there" etc
- Kconfig fixup for the TI IOdelay pinctrl-single add-on
- fix up a typo in the meson i2c ao groups
- switch a remapping back to use devm_ioremap() as
devm_ioremap_resource() does not allow for sharing memory regions
- do not clear the Qualcomm irq status bit in irq_unmask(), as this
can lead to missing interrupts while the irq handler is executing
- add irq_request/release_resources() on the ST driver
- add a bunch of mysteriously missing pingroups for high numbered
pins in the Qualcomm ipq4019 driver"
* tag 'pinctrl-v4.11-3' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
pinctrl: qcom: ipq4019: add missing pingroups for pins > 70
pinctrl: st: add irq_request/release_resources callbacks
pinctrl: qcom: Don't clear status bit on irq_unmask
pinctrl: samsung: Fix memory mapping code
pinctrl: meson-gxbb: Fix typo in i2c ao groups
pinctrl: ti: The IODelay driver is a DRA7xxx feature so depend on that SoC
A smattering of different small fixes for some random driver subsystems.
Nothing all that major, just resolutions for reported issues and bugs.
All have been in linux-next with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWNedPQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykY+wCeL0dFw/ney0sJ6s7HsmXu3uxFGyoAoIIXL7AP
48YAht+BOOmBzagXIKbw
=EFxm
-----END PGP SIGNATURE-----
Merge tag 'char-misc-4.11-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver fixes from Greg KH:
"A smattering of different small fixes for some random driver
subsystems. Nothing all that major, just resolutions for reported
issues and bugs.
All have been in linux-next with no reported issues"
* tag 'char-misc-4.11-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (21 commits)
extcon: int3496: Set the id pin to direction-input if necessary
extcon: int3496: Use gpiod_get instead of gpiod_get_index
extcon: int3496: Add dependency on X86 as it's Intel specific
extcon: int3496: Add GPIO ACPI mapping table
extcon: int3496: Rename GPIO pins in accordance with binding
vmw_vmci: handle the return value from pci_alloc_irq_vectors correctly
ppdev: fix registering same device name
parport: fix attempt to write duplicate procfiles
auxdisplay: img-ascii-lcd: add missing sentinel entry in img_ascii_lcd_matches
Drivers: hv: vmbus: Don't leak memory when a channel is rescinded
Drivers: hv: vmbus: Don't leak channel ids
Drivers: hv: util: don't forget to init host_ts.lock
Drivers: hv: util: move waiting for release to hv_utils_transport itself
vmbus: remove hv_event_tasklet_disable/enable
vmbus: use rcu for per-cpu channel list
mei: don't wait for os version message reply
mei: fix deadlock on mei reset
intel_th: pci: Add Gemini Lake support
intel_th: pci: Add Denverton SOC support
intel_th: Don't leak module refcount on failure to activate
...
Here is a single kernfs fix for 4.11-rc4 that resolves a reported issue.
It has been in linux-next with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWNedpw8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykLkgCdEVdmtWb9Fd0igfh7bSWBHdD9W20An3vKOror
nTP7sT8FwSWGKdOpIaik
=0Eht
-----END PGP SIGNATURE-----
Merge tag 'driver-core-4.11-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core fix from Greg KH:
"Here is a single kernfs fix for 4.11-rc4 that resolves a reported
issue.
It has been in linux-next with no reported issues"
* tag 'driver-core-4.11-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
kernfs: Check KERNFS_HAS_RELEASE before calling kernfs_release_file()
Here are some tty and serial driver fixes for 4.11-rc4. One of these
fix a long-standing issue in the ldisc code that was found by Dmitry
Vyukov with his great fuzzing work. The other fixes resolve other
reported issues, and there is one revert of a patch in 4.11-rc1 that
wasn't correct.
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWNeexA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykTSQCg11kA9FkRe28wurC7hljx8tcnBmsAoNE5Arw8
b3NfQ3Sm50gVPXxKQPWZ
=WyEk
-----END PGP SIGNATURE-----
Merge tag 'tty-4.11-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial driver fixes from Greg KH:
"Here are some tty and serial driver fixes for 4.11-rc4.
One of these fix a long-standing issue in the ldisc code that was
found by Dmitry Vyukov with his great fuzzing work. The other fixes
resolve other reported issues, and there is one revert of a patch in
4.11-rc1 that wasn't correct.
All of these have been in linux-next for a while with no reported
issues"
* tag 'tty-4.11-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
tty: fix data race in tty_ldisc_ref_wait()
tty: don't panic on OOM in tty_set_ldisc()
Revert "tty: serial: pl011: add ttyAMA for matching pl011 console"
tty: acpi/spcr: QDF2400 E44 checks for wrong OEM revision
serial: 8250_dw: Fix breakage when HAVE_CLK=n
serial: 8250_dw: Honor clk_round_rate errors in dw8250_set_termios
Here are some small IIO driver fixes for 4.11-rc4 that resolve a number
of tiny reported issues. All of these have been in linux-next for a
while with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWNeeCg8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ynXYwCcC+ZqoQ2zyAXI9NRNzADGqLgVLDkAoL5emrPe
10VBu7ocPtuAI12QdcGI
=xfgR
-----END PGP SIGNATURE-----
Merge tag 'staging-4.11-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull IIO driver fixes from Greg KH:
"Here are some small IIO driver fixes for 4.11-rc4 that resolve a
number of tiny reported issues. All of these have been in linux-next
for a while with no reported issues"
* tag 'staging-4.11-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
iio: imu: st_lsm6dsx: fix FIFO_CTRL2 overwrite during watermark configuration
iio: adc: ti_am335x_adc: fix fifo overrun recovery
iio: sw-device: Fix config group initialization
iio: magnetometer: ak8974: remove incorrect __exit markups
iio: hid-sensor-trigger: Change get poll value function order to avoid sensor properties losing after resume from S3
Here are a number of small USB and PHY driver fixes for 4.11-rc4.
Nothing major here, just an bunch of small fixes, and a handfull of good
fixes from Johan for devices with crazy descriptors. There are a few
new device ids in here as well.
All of these have been in linux-next with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWNefwQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykewwCg1P1HEZV2wLJSalsPxduIKIRLcmkAnRcE0H31
2egrp1seSGQumYcGQUJ/
=2fH+
-----END PGP SIGNATURE-----
Merge tag 'usb-4.11-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB/PHY fixes from Greg KH:
"Here are a number of small USB and PHY driver fixes for 4.11-rc4.
Nothing major here, just an bunch of small fixes, and a handfull of
good fixes from Johan for devices with crazy descriptors. There are a
few new device ids in here as well.
All of these have been in linux-next with no reported issues"
* tag 'usb-4.11-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (26 commits)
usb: gadget: f_hid: fix: Don't access hidg->req without spinlock held
usb: gadget: udc: remove pointer dereference after free
usb: gadget: f_uvc: Sanity check wMaxPacketSize for SuperSpeed
usb: gadget: f_uvc: Fix SuperSpeed companion descriptor's wBytesPerInterval
usb: gadget: acm: fix endianness in notifications
usb: dwc3: gadget: delay unmap of bounced requests
USB: serial: qcserial: add Dell DW5811e
usb: hub: Fix crash after failure to read BOS descriptor
ACM gadget: fix endianness in notifications
USB: usbtmc: fix probe error path
USB: usbtmc: add missing endpoint sanity check
USB: serial: option: add Quectel UC15, UC20, EC21, and EC25 modems
usb: musb: fix possible spinlock deadlock
usb: musb: dsps: fix iounmap in error and exit paths
usb: musb: cppi41: don't check early-TX-interrupt for Isoch transfer
usb-core: Add LINEAR_FRAME_INTR_BINTERVAL USB quirk
uwb: i1480-dfu: fix NULL-deref at probe
uwb: hwa-rc: fix NULL-deref at probe
USB: wusbcore: fix NULL-deref at probe
USB: uss720: fix NULL-deref at probe
...
- cxl: Route eeh events to all slices for pci_channel_io_perm_failure state
- powerpc/64s: Fix idle wakeup potential to clobber registers
- Revert "powerpc/64: Disable use of radix under a hypervisor"
- gcc-plugins: update architecture list in documentation
Thanks to:
Andrew Donnellan, Nicholas Piggin, Paul Mackerras, Vaibhav Jain.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=4CFb
-----END PGP SIGNATURE-----
Merge tag 'powerpc-4.11-6' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull more powerpc fixes from Michael Ellerman:
"These are all pretty minor. The fix for idle wakeup would be a bad bug
but has not been observed in practice.
The update to the gcc-plugins docs was Cc'ed to Kees and Jon, Kees
OK'ed it going via powerpc and I didn't hear from Jon.
- cxl: Route eeh events to all slices for pci_channel_io_perm_failure state
- powerpc/64s: Fix idle wakeup potential to clobber registers
- Revert "powerpc/64: Disable use of radix under a hypervisor"
- gcc-plugins: update architecture list in documentation
Thanks to: Andrew Donnellan, Nicholas Piggin, Paul Mackerras, Vaibhav
Jain"
* tag 'powerpc-4.11-6' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
gcc-plugins: update architecture list in documentation
Revert "powerpc/64: Disable use of radix under a hypervisor"
powerpc/64s: Fix idle wakeup potential to clobber registers
cxl: Route eeh events to all slices for pci_channel_io_perm_failure state
