At least on the platforms that have a dp aux irq and also have it
enabled - vlvhsw should have one, too. But I don't have a machine to
test this on. Judging from docs there's no dp aux interrupt for gm45.
Also, I only have an ivb cpu edp machine, so the dp aux A code for
snb/ilk is untested.
For dpcd probing when nothing is connected it slashes about 5ms of cpu
time (cpu time is now negligible), which agrees with 3 * 5 400 usec
timeouts.
A previous version of this patch increases the time required to go
through the dp_detect cycle (which includes reading the edid) from
around 33 ms to around 40 ms. Experiments indicated that this is
purely due to the irq latency - the hw doesn't allow us to queue up
dp aux transactions and hence irq latency directly affects throughput.
gmbus is much better, there we have a 8 byte buffer, and we get the
irq once another 4 bytes can be queued up.
But by using the pm_qos interface to request the lowest possible cpu
wake-up latency this slowdown completely disappeared.
Since all our output detection logic is single-threaded with the
mode_config mutex right now anyway, I've decide not ot play fancy and
to just reuse the gmbus wait queue. But this would definitely prep the
way to run dp detection on different ports in parallel
v2: Add a timeout for dp aux transfers when using interrupts - the hw
_does_ prevent this with the hw-based 400 usec timeout, but if the
irq somehow doesn't arrive we're screwed. Lesson learned while
developing this ;-)
v3: While at it also convert the busy-loop to wait_for_atomic, so that
we don't run the risk of an infinite loop any more.
v4: Ensure we have the smallest possible irq latency by using the
pm_qos interface.
v5: Add a comment to the code to explain why we frob pm_qos. Suggested
by Chris Wilson.
v6: Disable dp irq for vlv, that's easier than trying to get at docs
and hw.
v7: Squash in a fix for Haswell that Paulo Zanoni tracked down - the
dp aux registers aren't at a fixed offset any more, but can be on the
PCH while the DP port is on the cpu die.
Reviewed-by: Imre Deak <imre.deak@intel.com> (v6)
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Use drm_dp_bw_code_to_link_rate insead. It's the same thing, but
supports DP_LINK_BW_5_4 and is also used by the other drivers.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
And use it whenever we call code that uses the DDIs. We already have
intel_ddi.c and prefix every function with intel_ddi_something instead of
haswell_something, so I think replacing the checks with HAS_DDI makes more
sense. Just a cosmetical change, yes I know, but I have this OCD...
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
v2: Rebased.
Signed-off-by: Rob Clark <rob@ti.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com> (v1)
[danvet: Pimp commit message a bit.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Daniel writes:
Highlights of this -next round:
- ivb fdi B/C fixes
- hsw sprite/plane offset fixes from Damien
- unified dp/hdmi encoder for hsw, finally external dp support on hsw
(Paulo)
- kill-agp and some other prep work in the gtt code from Ben
- some fb handling fixes from Ville
- massive pile of patches to align hsw VGA with the spec and make it
actually work (Paulo)
- pile of workarounds from Jesse, mostly for vlv, but also some other
related platforms
- start of a dev_priv reorg, that thing grew out of bounds and chaotic
- small bits&pieces all over the place, down to better error handling for
load-detect on gen2 (Chris, Jani, Mika, Zhenyu, ...)
On top of the previous pile (just copypasta):
- tons of hsw dp prep patches form Paulo
- round scheduled work items and timers to nearest second (Chris)
- some hw workarounds (Jesse&Damien)
- vlv dp support and related fixups (Vijay et al.)
- basic haswell dp support, not yet wired up for external ports (Paulo)
- edp support (Paulo)
- tons of refactorings to prepare for the above (Paulo)
- panel rework, unifiying code between lvds and edp panels (Jani)
- panel fitter scaling modes (Jani + Yuly Novikov)
- panel power improvements, should now work without the BIOS setting it up
- extracting some dp helpers from radeon/i915 and move them to
drm_dp_helper.c
- randome pile of workarounds (Damien, Ben, ...)
- some cleanups for the register restore code for suspend/resume
- secure batchbuffer support, should enable tear-free blits on gen6+
Chris)
- random smaller fixlets and cleanups.
* 'for-airlied' of git://people.freedesktop.org/~danvet/drm-intel: (231 commits)
drm/i915: Restore physical HWS_PGA after resume
drm/i915: Report amount of usable graphics memory in MiB
drm/i915/i2c: Track users of GMBUS force-bit
drm/i915: Allocate the proper size for contexts.
drm/i915: Update load-detect failure paths for modeset-rework
drm/i915: Clear unused fields of mode for framebuffer creation
drm/i915: Always calculate 8xx WM values based on a 32-bpp framebuffer
drm/i915: Fix sparse warnings in from AGP kill code
drm/i915: Missed lock change with rps lock
drm/i915: Move the remaining gtt code
drm/i915: flush system agent TLBs on SNB
drm/i915: Kill off now unused gen6+ AGP code
drm/i915: Calculate correct stolen size for GEN7+
drm/i915: Stop using AGP layer for GEN6+
drm/i915: drop the double-OP_STOREDW usage in blt_ring_flush
drm/i915: don't rewrite the GTT on resume v4
drm/i915: protect RPS/RC6 related accesses (including PCU) with a new mutex
drm/i915: put ring frequency and turbo setup into a work queue v5
drm/i915: don't block resume on fb console resume v2
drm/i915: extract l3_parity substruct from dev_priv
...
Now intel_ddi_init is just like intel_hdmi_init and intel_dp_init: it
inits the encoder and then calls the proper init_connector functions.
Notice that for non-eDP ports we call both HDMI and DP connector init,
so we have 2 connectors attached to each DDI encoder.
After this change, intel_hdmi_init and intel_dp_init are only called
by Ivy Bridge and earlier, while hardware containing DDI outputs
should call intel_ddi_init.
Also added/removed quite a few "static" keywords due to the fact that
some function pointers were moved from intel_dp.c and intel_hdmi.c to
intel_ddi.c.
DP finally works on Haswell now! \o/
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We need this since now on DDI we will have 2 connectors on each
encoder.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Both "intel_dp" and "intel_hdmi" structs had a "port" field, which
always had the same value. It makes more sense to move this to
intel_digital_port, so we can know the port independently of the
connector type.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
When intel_hdmi_detect detects a monitor, set intel_encoder->type with
INTEL_OUTPUT_HDMI. Same for DP.
This should not break the current code because these variables never
change. This will be used after we create the DDI encoder because it
will have both DP and HDMI connectors.
We won't support eDP+HDMI on the same port, so if an encoder is eDP we
should expect it to always remain eDP and never change.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Same reason as the previous HDMI commit: the DDI code will have its
own encoder init function but still use the DP and HDMI connectors.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
[danvet: kill the unnecessarily added line that Damien spotted in
review.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The goal is to have one single encoder capable of controlling both DP
and HDMI outputs. This patch just adds the initial infrastructure, no
functional changes.
Previously, both intel_dp and intel_hdmi were intel_encoders. Now,
these 2 structs do not have intel_encoder as members anymore. The new
struct intel_digital_port has intel_encoder as a member, and it also
includes intel_dp and intel_hdmi as members. In other words: see the
changes inside intel_drv.h: it's the most important change, everything
else is only to make it compile and work.
For now, each intel_digital_port is still only able to control one of
HDMI or DP, but not both together.
In the future we should also try to merge the common fields from
intel_dp and intel_hdmi (e.g., port).
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
[danvet: Add the missing ' ' spotted by Damien Lespiau.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
When we add struct intel_digital_port, there will be no direct way of
going from intel_{dp,hdmi} to drm_device: we will need to call
container_of().
This patch adds functions to go from intel_{dp,hdmi} to drm_device.
The main goal here is to greatly reduce the size of the next patch,
where we will change the implementation of the functions we just
added here (among other things).
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
- Replace container_of with enc_to_intel_dp.
- Walk through less structures when making assignments.
- Rename some variables to keep our naming standards.
As a bonus, this will reduce the usage of "struct intel_dp", making
the future patch that introduces intel_digital_port smaller and easier
to review.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The debug message is only relevant on CPT/PPT PCH ports, so move
it into the correct if clause.
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Yuly Novikov <ynovikov@chromium.org>
[Jani: ripped this change separate from the scaling mode change support]
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Tested-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
At some point the DPCD size was increased, but the debug print not. While
at it, switch to using hex dump.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
It's an important step :)
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The cdclk frequency is not always the same, so the value here should
be adjusted to match it.
Version 2: call intel_ddi_get_cdclk_freq instead of reading
CDCLK_FREQ, because the register is just for earlier HW steppings.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Same thing as the previous commits. Not renaming this one since it
exists since way before Haswell.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
That thing has grown way too big already.
Also move around a comment to the right spot.
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Tested-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Otherwise dp aux won't work on some hsw platforms, since they use a
different rawclk than the 125MHz clock used thus far.
To absolutely not change anything, round up: That way we get the old
63 divider for the default 125MHz clock.
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Tested-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We need this when the bios forgets even to set that bit up. Most seem
to do that, even when they don't set up anything else in the panel
power sequencer.
Note that on IBX the rawclk is variable according to Bspec, but
everyone is using 125MHz. The rawclk is fixed to 125MHz on CPT, but
luckily we still have the same register available. On hsw, different
variants have different clocks, hence we need to check the register.
Since other pieces are driven by the rawclock, too, keep the little
helper in a central place.
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Tested-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Like we already do for the LVDS panels. This seems to help greatly
in setting up the backlight, since the BIOS might refuse to cooperate.
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Tested-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
v2: Move the backlight_off call from panel_off to edp_backlight_off,
noticed by Paulo Zanoni.
Reviewed-by: Paulo Zanoni <przanoni@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
3 changes:
- If a given value is unset, use the maximal limits from the eDP spec.
- Write back the new values, since otherwise the panel power sequencing
hw will not dtrt.
- Revert the early bail-out in case the register values are unset.
The last change reverts
commit bfa3384a9a
Author: Jesse Barnes <jbarnes@virtuousgeek.org>
Date: Tue Apr 10 11:58:04 2012 -0700
drm/i915: check PPS regs for sanity when using eDP
v2:
- Unlock the PP regs as the very first thing. This is a required w/a
for cpu eDP on port A, and generally a good idea.
- Fixup the panel power control port selection bits.
v3: Paulo Zanoni noticed that I've fumbled the computation of the spec
limit values. Fix them up. We've also noticed that the t8/t9 values in
the vbt/bios-programmed pp are much larger than any limits. My guess
is that this is to conceal any backlight enable/disable delays. So by
using the much shorter limits from the spec, which only concerns the
sink, we risk that we might display before the backlight is fully on,
or disable the output while the backlight still has afterglow. I've
figured I don't care too much, since this will only happen when both
the pp regs are not programmed, and the vbt tables don't contain
anything useful.
v4: Don't set the port selection bits on hsw/LPT, they don't exist any
more.
v5: Fixup spelling issues in comments, as noticed by Jesse Barnes.
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Tested-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
... like the comment says. No idea whether this has any effect, but
I guess it's better to not lie to the display by acking a test request
and never following through with it. This goes back to the commit that
originally introduced this code:
commit a60f0e38d7
Author: Jesse Barnes <jbarnes@virtuousgeek.org>
Date: Thu Oct 20 15:09:17 2011 -0700
drm/i915: add DP test request handling
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Meh'ed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Only really required for dp 1.2. I've hoped this would help with some
link training woes I'm fighting, but alas those are only dp 1.1
devices.
Also move a comment that went misplaced in the recent refactorings to
the right spot again.
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This requires a few changes since that dpcd value is above the
range currently cached by radeon. I've check the dp specs, and
above 0xf there's a big gap and nothing that looks like we should
cache it while a given device is plugged in. It's also the same value
that i915.ko uses.
Hence extend the various dpcd arrays in the radeon driver, use
proper symbolic constants where applicable (one place overallocated
the dpcd array to 25 bytes). Then also drop the rd_interval cache -
radeon_dp_link_train_init re-reads the dpcd block, so the values we'll
consume in train_cr and train_ce will always be fresh.
To avoid needless diff-churn, #define the old size of dpcd as the new
one and keep it around.
v2: Alex Deucher noticed one place where I've forgotten to replace 8
with DP_RECEIVER_CAP_SIZE.
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Acked-by: Dave Airlie <airlied@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Safe for the minor difference that the intel versions get an offset
into the link_status as an argument, both are the same again.
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Acked-by: Dave Airlie <airlied@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
radeon and intel use the exact same definition.
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Acked-by: Dave Airlie <airlied@gmail.com>
v2: Kill 2 more helpers in intel_dp.c that I've missed.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
radeon and intel use the exact same definition.
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Acked-by: Dave Airlie <airlied@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Move the cached EDID from intel_dp and intel_lvds_connector to
intel_connector. Unify cached EDID handling for LVDS and eDP, in
preparation for adding more generic EDID caching later.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Pave the way for sharing some logic between eDP and LVDS.
Based on earlier work by Chris Wilson <chris@chris-wilson.co.uk>
CC: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Create a generic struct intel_panel for sharing a data structure and code
between eDP and LVDS panels. Add the new struct to intel_connector so that
later on we can have generic EDID and mode reading functions with EDID
caching that transparently fallback to fixed mode when EDID is not
available.
Add intel_panel as a dummy first, and move data (such as the mentioned
fixed mode) to it in later patches.
Based on earlier work by Chris Wilson <chris@chris-wilson.co.uk>
CC: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
[danvet: Fixup tiny conflict in intel_dp_destroy.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Since we do EDID caching in intel_dp_init, we can do the fixed mode
initialization there too. This should not change the functionality apart
from initializing fixed mode earlier. Particularly retain the behaviour of
only falling back to VBT if EDID is not available to not regress
commit 47f0eb2234
Author: Keith Packard <keithp@keithp.com>
Date: Mon Sep 19 14:33:26 2011 -0700
drm/i915: Only use VBT panel mode on eDP if no EDID is found
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Get rid of saved int_lvds_connector and int_edp_connector in
drm_i915_private.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iQEcBAABAgAGBQJQgvdwAAoJEHm+PkMAQRiG+3AH/i2XsqqN3VctL0nnbWfvds+Q
aKulfIdJTjKiVAsawPUtRqReZ8ijiebrgA/53lZLlrFOoPPQ5+LHmnSyQF6gErOY
NuAE1lijXDRM1pwBlhvOBbAj26wUobGjqONFJ9OkKr758Ue8ds/Q7UdxyEgmYgmg
tvVMzfRcICzryUV3PcqL+3cNPpCUdT6wGGRJ9DCv/jvGiWKExWhOle5oltrmxk+D
NsqRcws5pEubfHE4J8BvNWr8lE1kHfYVhrJETiLJUiN2XAJcbI4Jy7rU/3EGteNS
0HMZdaPPjV874lohdM70X2225SbYrCVkAYB5hnZCTeC3tYyCawBBPMQoyAiOcmU=
=+861
-----END PGP SIGNATURE-----
Merge tag 'v3.7-rc2' into drm-intel-next-queued
Linux 3.7-rc2
Backmerge to solve two ugly conflicts:
- uapi. We've already added new ioctl definitions for -next. Do I need to say more?
- wc support gtt ptes. We've had to revert this for snb+ for 3.7 and
also fix a few other things in the code. Now we know how to make it
work on snb+, but to avoid losing the other fixes do the backmerge
first before re-enabling wc gtt ptes on snb+.
And a few other minor things, among them git getting confused in
intel_dp.c and seemingly causing a conflict out of nothing ...
Conflicts:
drivers/gpu/drm/i915/i915_reg.h
drivers/gpu/drm/i915/intel_display.c
drivers/gpu/drm/i915/intel_dp.c
drivers/gpu/drm/i915/intel_modes.c
include/drm/i915_drm.h
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Daniel writes:
The big thing is the disabling of the hsw support by default, cc: stable.
We've aimed for basic hsw support in 3.6, but due to a few bad
happenstances we've screwed up and only 3.8 will have better modeset
support than vesa. To avoid yet another round of fallout from such a
gaffle on for the next platform we've added a module option to disable
early hw support by default. That should also give us more flexibility in
bring-up.
Otherwise just small fixes:
- 3 fixes from Egbert for sdvo corner cases
- invert-brightness quirk entry from Egbert
- revert a dp link training change, it regresses some setups
- and shut up a spurious WARN in our gem fault handler.
- regression fix for an oops on bit17 swizzling machines, introduce in 3.7
- another no-lvds quirk
* 'drm-intel-fixes' of git://people.freedesktop.org/~danvet/drm-intel:
drm/i915: Initialize obj->pages before use by i915_gem_object_do_bit17_swizzle()
drm/i915: Add no-lvds quirk for Supermicro X7SPA-H
drm/i915: Insert i915_preliminary_hw_support variable.
drm/i915: shut up spurious WARN in the gtt fault handler
Revert "drm/i915: Try harder to complete DP training pattern 1"
DRM/i915: Restore sdvo_flags after dtd->mode->dtd Roundrtrip.
DRM/i915: Don't clone SDVO LVDS with analog.
DRM/i915: Add QUIRK_INVERT_BRIGHTNESS for NCR machines.
DRM/i915: Don't delete DPLL Multiplier during DAC init.
This is the final remaining piece of Haswell DP enablement. After this
patch, just calling intel_dp_init on any port will make DP work. We
still do not do this because we're currently initializing HDMI on all
the ports, so if we replace intel_hdmi_init with intel_dp_init, we
will break HDMI, and we can't call both because they share the same
registers.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Previous patch "drm/i915: add basic Haswell DP link train bits"
implemented the basic structure to set the voltage levels and training
patterns. This patch adds the higher-level bits that are part of the
mode set sequence and hot plug.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We have to write the correct values inside intel_dp_set_m_n and then
prevent these values from being overwritten later.
V2: Unconfuse double negation.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The old rule that the AUX registers are just an offset (+4 and +10)
from output_reg is not true anymore, since output_reg in on the CPU
and some AUX regs are on the PCH.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
[danvet: use the existing #defines as spotted by Damien Lespiau.]
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Much simpler and looks more like the M/N code inside intel_display.c.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Previously, the DP register was used for everything. On Haswell, it
was split into DDI_BUF_CTL (which is the new intel_dp->DP register)
and DP_TP_CTL.
The logic behind this patch is based on a patch written by Shobhit
Kumar, but the way the code was written is very different.
Credits-to: Shobhit Kumar <shobhit.kumar@intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
[danvet: Fixup the logic error spotted by Jani Nikula.]
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This reverts commit 2477367083.
If (for whatever reason) the DP sink device never asks for the maximal
voltage level, we never don't hit the check that should bail us out
after 5 retries of the same voltage. Which leads to an endless loop in
the DP link training code, which hangs the driver.
Now some more DP link training experiments on eDP panels seem to
indicate that our training algorithm isn't robust enough anyway and
needs more work. Hence for 3.7-fixes, let's just revert the regressing
commit instead of trying to apply more duct-tape.
Reported-by: Oleksij Rempel <bug-track@fisher-privat.net>
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
