Conflicts:
drivers/net/can/dev.c
commit 03f16c5075 ("can: dev: can_restart: fix use after free bug")
commit 3e77f70e73 ("can: dev: move driver related infrastructure into separate subdir")
Code move.
drivers/net/dsa/b53/b53_common.c
commit 8e4052c32d ("net: dsa: b53: fix an off by one in checking "vlan->vid"")
commit b7a9e0da2d ("net: switchdev: remove vid_begin -> vid_end range from VLAN objects")
Field rename.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The multicast route ff00::/8 is created with type RTN_UNICAST:
$ ip -6 -d route
unicast ::1 dev lo proto kernel scope global metric 256 pref medium
unicast fe80::/64 dev eth0 proto kernel scope global metric 256 pref medium
unicast ff00::/8 dev eth0 proto kernel scope global metric 256 pref medium
Set the type to RTN_MULTICAST which is more appropriate.
Fixes: e8478e80e5 ("net/ipv6: Save route type in rt6_info")
Signed-off-by: Matteo Croce <mcroce@microsoft.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The ff00::/8 multicast route is created without specifying the fc_protocol
field, so the default RTPROT_BOOT value is used:
$ ip -6 -d route
unicast ::1 dev lo proto kernel scope global metric 256 pref medium
unicast fe80::/64 dev eth0 proto kernel scope global metric 256 pref medium
unicast ff00::/8 dev eth0 proto boot scope global metric 256 pref medium
As the documentation says, this value identifies routes installed during
boot, but the route is created when interface is set up.
Change the value to RTPROT_KERNEL which is a better value.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Matteo Croce <mcroce@microsoft.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
We need to unregister the netdevice if config failed.
.ndo_uninit takes care of most of the heavy lifting.
This was uncovered by recent commit c269a24ce0 ("net: make
free_netdev() more lenient with unregistering devices").
Previously the partially-initialized device would be left
in the system.
Reported-and-tested-by: syzbot+2393580080a2da190f04@syzkaller.appspotmail.com
Fixes: e2f1f072db ("sit: allow to configure 6rd tunnels via netlink")
Acked-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Link: https://lore.kernel.org/r/20210114012947.2515313-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
esp(6)_output_head uses skb_page_frag_refill to allocate a buffer for
the esp trailer.
It accesses the page with kmap_atomic to handle highmem. But
skb_page_frag_refill can return compound pages, of which
kmap_atomic only maps the first underlying page.
skb_page_frag_refill does not return highmem, because flag
__GFP_HIGHMEM is not set. ESP uses it in the same manner as TCP.
That also does not call kmap_atomic, but directly uses page_address,
in skb_copy_to_page_nocache. Do the same for ESP.
This issue has become easier to trigger with recent kmap local
debugging feature CONFIG_DEBUG_KMAP_LOCAL_FORCE_MAP.
Fixes: cac2661c53 ("esp4: Avoid skb_cow_data whenever possible")
Fixes: 03e2a30f6a ("esp6: Avoid skb_cow_data whenever possible")
Signed-off-by: Willem de Bruijn <willemb@google.com>
Acked-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
There are cases where GSO segment's length exceeds the egress MTU:
- Forwarding of a TCP GRO skb, when DF flag is not set.
- Forwarding of an skb that arrived on a virtualisation interface
(virtio-net/vhost/tap) with TSO/GSO size set by other network
stack.
- Local GSO skb transmitted on an NETIF_F_TSO tunnel stacked over an
interface with a smaller MTU.
- Arriving GRO skb (or GSO skb in a virtualised environment) that is
bridged to a NETIF_F_TSO tunnel stacked over an interface with an
insufficient MTU.
If so:
- Consume the SKB and its segments.
- Issue an ICMP packet with 'Packet Too Big' message containing the
MTU, allowing the source host to reduce its Path MTU appropriately.
Note: These cases are handled in the same manner in IPv4 output finish.
This patch aligns the behavior of IPv6 and the one of IPv4.
Fixes: 9e50849054 ("netfilter: ipv6: move POSTROUTING invocation before fragmentation")
Signed-off-by: Aya Levin <ayal@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://lore.kernel.org/r/1610027418-30438-1-git-send-email-ayal@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Unlike the rest of the skb_zcopy_ functions, these routines
operate on a 'struct ubuf', not a skb. Remove the 'skb_'
prefix from the naming to make things clearer.
Suggested-by: Willem de Bruijn <willemdebruijn.kernel@gmail.com>
Signed-off-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
At Willem's suggestion, rename the sock_zerocopy_* functions
so that they match the MSG_ZEROCOPY flag, which makes it clear
they are specific to this zerocopy implementation.
Signed-off-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The sock_zerocopy_put_abort function contains logic which is
specific to the current zerocopy implementation. Add a wrapper
which checks the callback and dispatches apppropriately.
Signed-off-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Route removal is handled by two code paths. The main removal path is via
fib6_del_route() which will handle purging any PMTU exceptions from the
cache, removing all per-cpu copies of the DST entry used by the route, and
releasing the fib6_info struct.
The second removal location is during fib6_add_rt2node() during a route
replacement operation. This path also calls fib6_purge_rt() to handle
cleaning up the per-cpu copies of the DST entries and releasing the
fib6_info associated with the older route, but it does not flush any PMTU
exceptions that the older route had. Since the older route is removed from
the tree during the replacement, we lose any way of accessing it again.
As these lingering DSTs and the fib6_info struct are holding references to
the underlying netdevice struct as well, unregistering that device from the
kernel can never complete.
Fixes: 2b760fcf5c ("ipv6: hook up exception table to store dst cache")
Signed-off-by: Sean Tranchetti <stranche@codeaurora.org>
Reviewed-by: David Ahern <dsahern@kernel.org>
Link: https://lore.kernel.org/r/1609892546-11389-1-git-send-email-stranche@quicinc.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Pablo Neira Ayuso says:
====================
Netfilter fixes for net
1) Incorrect loop in error path of nft_set_elem_expr_clone(),
from Colin Ian King.
2) Missing xt_table_get_private_protected() to access table
private data in x_tables, from Subash Abhinov Kasiviswanathan.
3) Possible oops in ipset hash type resize, from Vasily Averin.
4) Fix shift-out-of-bounds in ipset hash type, also from Vasily.
* git://git.kernel.org/pub/scm/linux/kernel/git/pablo/nf:
netfilter: ipset: fix shift-out-of-bounds in htable_bits()
netfilter: ipset: fixes possible oops in mtype_resize
netfilter: x_tables: Update remaining dereference to RCU
netfilter: nftables: fix incorrect increment of loop counter
====================
Link: https://lore.kernel.org/r/20201218120409.3659-1-pablo@netfilter.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This fixes the dereference to fetch the RCU pointer when holding
the appropriate xtables lock.
Reported-by: kernel test robot <lkp@intel.com>
Fixes: cc00bcaa58 ("netfilter: x_tables: Switch synchronization to RCU")
Signed-off-by: Subash Abhinov Kasiviswanathan <subashab@codeaurora.org>
Reviewed-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
-----BEGIN PGP SIGNATURE-----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=6Cqb
-----END PGP SIGNATURE-----
Merge tag 'selinux-pr-20201214' of git://git.kernel.org/pub/scm/linux/kernel/git/pcmoore/selinux
Pull selinux updates from Paul Moore:
"While we have a small number of SELinux patches for v5.11, there are a
few changes worth highlighting:
- Change the LSM network hooks to pass flowi_common structs instead
of the parent flowi struct as the LSMs do not currently need the
full flowi struct and they do not have enough information to use it
safely (missing information on the address family).
This patch was discussed both with Herbert Xu (representing team
netdev) and James Morris (representing team
LSMs-other-than-SELinux).
- Fix how we handle errors in inode_doinit_with_dentry() so that we
attempt to properly label the inode on following lookups instead of
continuing to treat it as unlabeled.
- Tweak the kernel logic around allowx, auditallowx, and dontauditx
SELinux policy statements such that the auditx/dontauditx are
effective even without the allowx statement.
Everything passes our test suite"
* tag 'selinux-pr-20201214' of git://git.kernel.org/pub/scm/linux/kernel/git/pcmoore/selinux:
lsm,selinux: pass flowi_common instead of flowi to the LSM hooks
selinux: Fix fall-through warnings for Clang
selinux: drop super_block backpointer from superblock_security_struct
selinux: fix inode_doinit_with_dentry() LABEL_INVALID error handling
selinux: allow dontauditx and auditallowx rules to take effect without allowx
selinux: fix error initialization in inode_doinit_with_dentry()
Core:
- support "prefer busy polling" NAPI operation mode, where we defer softirq
for some time expecting applications to periodically busy poll
- AF_XDP: improve efficiency by more batching and hindering
the adjacency cache prefetcher
- af_packet: make packet_fanout.arr size configurable up to 64K
- tcp: optimize TCP zero copy receive in presence of partial or unaligned
reads making zero copy a performance win for much smaller messages
- XDP: add bulk APIs for returning / freeing frames
- sched: support fragmenting IP packets as they come out of conntrack
- net: allow virtual netdevs to forward UDP L4 and fraglist GSO skbs
BPF:
- BPF switch from crude rlimit-based to memcg-based memory accounting
- BPF type format information for kernel modules and related tracing
enhancements
- BPF implement task local storage for BPF LSM
- allow the FENTRY/FEXIT/RAW_TP tracing programs to use bpf_sk_storage
Protocols:
- mptcp: improve multiple xmit streams support, memory accounting and
many smaller improvements
- TLS: support CHACHA20-POLY1305 cipher
- seg6: add support for SRv6 End.DT4/DT6 behavior
- sctp: Implement RFC 6951: UDP Encapsulation of SCTP
- ppp_generic: add ability to bridge channels directly
- bridge: Connectivity Fault Management (CFM) support as is defined in
IEEE 802.1Q section 12.14.
Drivers:
- mlx5: make use of the new auxiliary bus to organize the driver internals
- mlx5: more accurate port TX timestamping support
- mlxsw:
- improve the efficiency of offloaded next hop updates by using
the new nexthop object API
- support blackhole nexthops
- support IEEE 802.1ad (Q-in-Q) bridging
- rtw88: major bluetooth co-existance improvements
- iwlwifi: support new 6 GHz frequency band
- ath11k: Fast Initial Link Setup (FILS)
- mt7915: dual band concurrent (DBDC) support
- net: ipa: add basic support for IPA v4.5
Refactor:
- a few pieces of in_interrupt() cleanup work from Sebastian Andrzej Siewior
- phy: add support for shared interrupts; get rid of multiple driver
APIs and have the drivers write a full IRQ handler, slight growth
of driver code should be compensated by the simpler API which
also allows shared IRQs
- add common code for handling netdev per-cpu counters
- move TX packet re-allocation from Ethernet switch tag drivers to
a central place
- improve efficiency and rename nla_strlcpy
- number of W=1 warning cleanups as we now catch those in a patchwork
build bot
Old code removal:
- wan: delete the DLCI / SDLA drivers
- wimax: move to staging
- wifi: remove old WDS wifi bridging support
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
-----BEGIN PGP SIGNATURE-----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=GXs1
-----END PGP SIGNATURE-----
Merge tag 'net-next-5.11' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next
Pull networking updates from Jakub Kicinski:
"Core:
- support "prefer busy polling" NAPI operation mode, where we defer
softirq for some time expecting applications to periodically busy
poll
- AF_XDP: improve efficiency by more batching and hindering the
adjacency cache prefetcher
- af_packet: make packet_fanout.arr size configurable up to 64K
- tcp: optimize TCP zero copy receive in presence of partial or
unaligned reads making zero copy a performance win for much smaller
messages
- XDP: add bulk APIs for returning / freeing frames
- sched: support fragmenting IP packets as they come out of conntrack
- net: allow virtual netdevs to forward UDP L4 and fraglist GSO skbs
BPF:
- BPF switch from crude rlimit-based to memcg-based memory accounting
- BPF type format information for kernel modules and related tracing
enhancements
- BPF implement task local storage for BPF LSM
- allow the FENTRY/FEXIT/RAW_TP tracing programs to use
bpf_sk_storage
Protocols:
- mptcp: improve multiple xmit streams support, memory accounting and
many smaller improvements
- TLS: support CHACHA20-POLY1305 cipher
- seg6: add support for SRv6 End.DT4/DT6 behavior
- sctp: Implement RFC 6951: UDP Encapsulation of SCTP
- ppp_generic: add ability to bridge channels directly
- bridge: Connectivity Fault Management (CFM) support as is defined
in IEEE 802.1Q section 12.14.
Drivers:
- mlx5: make use of the new auxiliary bus to organize the driver
internals
- mlx5: more accurate port TX timestamping support
- mlxsw:
- improve the efficiency of offloaded next hop updates by using
the new nexthop object API
- support blackhole nexthops
- support IEEE 802.1ad (Q-in-Q) bridging
- rtw88: major bluetooth co-existance improvements
- iwlwifi: support new 6 GHz frequency band
- ath11k: Fast Initial Link Setup (FILS)
- mt7915: dual band concurrent (DBDC) support
- net: ipa: add basic support for IPA v4.5
Refactor:
- a few pieces of in_interrupt() cleanup work from Sebastian Andrzej
Siewior
- phy: add support for shared interrupts; get rid of multiple driver
APIs and have the drivers write a full IRQ handler, slight growth
of driver code should be compensated by the simpler API which also
allows shared IRQs
- add common code for handling netdev per-cpu counters
- move TX packet re-allocation from Ethernet switch tag drivers to a
central place
- improve efficiency and rename nla_strlcpy
- number of W=1 warning cleanups as we now catch those in a patchwork
build bot
Old code removal:
- wan: delete the DLCI / SDLA drivers
- wimax: move to staging
- wifi: remove old WDS wifi bridging support"
* tag 'net-next-5.11' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (1922 commits)
net: hns3: fix expression that is currently always true
net: fix proc_fs init handling in af_packet and tls
nfc: pn533: convert comma to semicolon
af_vsock: Assign the vsock transport considering the vsock address flags
af_vsock: Set VMADDR_FLAG_TO_HOST flag on the receive path
vsock_addr: Check for supported flag values
vm_sockets: Add VMADDR_FLAG_TO_HOST vsock flag
vm_sockets: Add flags field in the vsock address data structure
net: Disable NETIF_F_HW_TLS_TX when HW_CSUM is disabled
tcp: Add logic to check for SYN w/ data in tcp_simple_retransmit
net: mscc: ocelot: install MAC addresses in .ndo_set_rx_mode from process context
nfc: s3fwrn5: Release the nfc firmware
net: vxget: clean up sparse warnings
mlxsw: spectrum_router: Use eXtended mezzanine to offload IPv4 router
mlxsw: spectrum: Set KVH XLT cache mode for Spectrum2/3
mlxsw: spectrum_router_xm: Introduce basic XM cache flushing
mlxsw: reg: Add Router LPM Cache Enable Register
mlxsw: reg: Add Router LPM Cache ML Delete Register
mlxsw: spectrum_router_xm: Implement L-value tracking for M-index
mlxsw: reg: Add XM Router M Table Register
...
Pablo Neira Ayuso says:
====================
Netfilter/IPVS updates for net-next
1) Missing dependencies in NFT_BRIDGE_REJECT, from Randy Dunlap.
2) Use atomic_inc_return() instead of atomic_add_return() in IPVS,
from Yejune Deng.
3) Simplify check for overquota in xt_nfacct, from Kaixu Xia.
4) Move nfnl_acct_list away from struct net, from Miao Wang.
5) Pass actual sk in reject actions, from Jan Engelhardt.
6) Add timeout and protoinfo to ctnetlink destroy events,
from Florian Westphal.
7) Four patches to generalize set infrastructure to support
for multiple expressions per set element.
* git://git.kernel.org/pub/scm/linux/kernel/git/pablo/nf-next:
netfilter: nftables: netlink support for several set element expressions
netfilter: nftables: generalize set extension to support for several expressions
netfilter: nftables: move nft_expr before nft_set
netfilter: nftables: generalize set expressions support
netfilter: ctnetlink: add timeout and protoinfo to destroy events
netfilter: use actual socket sk for REJECT action
netfilter: nfnl_acct: remove data from struct net
netfilter: Remove unnecessary conversion to bool
ipvs: replace atomic_add_return()
netfilter: nft_reject_bridge: fix build errors due to code movement
====================
Link: https://lore.kernel.org/r/20201212230513.3465-1-pablo@netfilter.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Pull crypto updates from Herbert Xu:
"API:
- Add speed testing on 1420-byte blocks for networking
Algorithms:
- Improve performance of chacha on ARM for network packets
- Improve performance of aegis128 on ARM for network packets
Drivers:
- Add support for Keem Bay OCS AES/SM4
- Add support for QAT 4xxx devices
- Enable crypto-engine retry mechanism in caam
- Enable support for crypto engine on sdm845 in qce
- Add HiSilicon PRNG driver support"
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6: (161 commits)
crypto: qat - add capability detection logic in qat_4xxx
crypto: qat - add AES-XTS support for QAT GEN4 devices
crypto: qat - add AES-CTR support for QAT GEN4 devices
crypto: atmel-i2c - select CONFIG_BITREVERSE
crypto: hisilicon/trng - replace atomic_add_return()
crypto: keembay - Add support for Keem Bay OCS AES/SM4
dt-bindings: Add Keem Bay OCS AES bindings
crypto: aegis128 - avoid spurious references crypto_aegis128_update_simd
crypto: seed - remove trailing semicolon in macro definition
crypto: x86/poly1305 - Use TEST %reg,%reg instead of CMP $0,%reg
crypto: x86/sha512 - Use TEST %reg,%reg instead of CMP $0,%reg
crypto: aesni - Use TEST %reg,%reg instead of CMP $0,%reg
crypto: cpt - Fix sparse warnings in cptpf
hwrng: ks-sa - Add dependency on IOMEM and OF
crypto: lib/blake2s - Move selftest prototype into header file
crypto: arm/aes-ce - work around Cortex-A57/A72 silion errata
crypto: ecdh - avoid unaligned accesses in ecdh_set_secret()
crypto: ccree - rework cache parameters handling
crypto: cavium - Use dma_set_mask_and_coherent to simplify code
crypto: marvell/octeontx - Use dma_set_mask_and_coherent to simplify code
...
xdp_return_frame_bulk() needs to pass a xdp_buff
to __xdp_return().
strlcpy got converted to strscpy but here it makes no
functional difference, so just keep the right code.
Conflicts:
net/netfilter/nf_tables_api.c
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Pablo Neira Ayuso says:
====================
Netfilter fixes for net
The following patchset contains Netfilter fixes for net:
1) Switch to RCU in x_tables to fix possible NULL pointer dereference,
from Subash Abhinov Kasiviswanathan.
2) Fix netlink dump of dynset timeouts later than 23 days.
3) Add comment for the indirect serialization of the nft commit mutex
with rtnl_mutex.
4) Remove bogus check for confirmed conntrack when matching on the
conntrack ID, from Brett Mastbergen.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
For DCTCP, we have to retain the ECT bits set by the congestion control
algorithm on the socket when reflecting syn TOS in syn-ack, in order to
make ECN work properly.
Fixes: ac8f1710c1 ("tcp: reflect tos value received in SYN to the socket")
Reported-by: Alexander Duyck <alexanderduyck@fb.com>
Signed-off-by: Wei Wang <weiwan@google.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When running concurrent iptables rules replacement with data, the per CPU
sequence count is checked after the assignment of the new information.
The sequence count is used to synchronize with the packet path without the
use of any explicit locking. If there are any packets in the packet path using
the table information, the sequence count is incremented to an odd value and
is incremented to an even after the packet process completion.
The new table value assignment is followed by a write memory barrier so every
CPU should see the latest value. If the packet path has started with the old
table information, the sequence counter will be odd and the iptables
replacement will wait till the sequence count is even prior to freeing the
old table info.
However, this assumes that the new table information assignment and the memory
barrier is actually executed prior to the counter check in the replacement
thread. If CPU decides to execute the assignment later as there is no user of
the table information prior to the sequence check, the packet path in another
CPU may use the old table information. The replacement thread would then free
the table information under it leading to a use after free in the packet
processing context-
Unable to handle kernel NULL pointer dereference at virtual
address 000000000000008e
pc : ip6t_do_table+0x5d0/0x89c
lr : ip6t_do_table+0x5b8/0x89c
ip6t_do_table+0x5d0/0x89c
ip6table_filter_hook+0x24/0x30
nf_hook_slow+0x84/0x120
ip6_input+0x74/0xe0
ip6_rcv_finish+0x7c/0x128
ipv6_rcv+0xac/0xe4
__netif_receive_skb+0x84/0x17c
process_backlog+0x15c/0x1b8
napi_poll+0x88/0x284
net_rx_action+0xbc/0x23c
__do_softirq+0x20c/0x48c
This could be fixed by forcing instruction order after the new table
information assignment or by switching to RCU for the synchronization.
Fixes: 80055dab5d ("netfilter: x_tables: make xt_replace_table wait until old rules are not used anymore")
Reported-by: Sean Tranchetti <stranche@codeaurora.org>
Reported-by: kernel test robot <lkp@intel.com>
Suggested-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Subash Abhinov Kasiviswanathan <subashab@codeaurora.org>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
SRv6 End.DT6 is defined in the SRv6 Network Programming [1].
The Linux kernel already offers an implementation of the SRv6
End.DT6 behavior which permits IPv6 L3 VPNs over SRv6 networks. This
implementation is not particularly suitable in contexts where we need to
deploy IPv6 L3 VPNs among different tenants which share the same network
address schemes. The underlying problem lies in the fact that the
current version of DT6 (called legacy DT6 from now on) needs a complex
configuration to be applied on routers which requires ad-hoc routes and
routing policy rules to ensure the correct isolation of tenants.
Consequently, a new implementation of DT6 has been introduced with the
aim of simplifying the construction of IPv6 L3 VPN services in the
multi-tenant environment using SRv6 networks. To accomplish this task,
we reused the same VRF infrastructure and SRv6 core components already
exploited for implementing the SRv6 End.DT4 behavior.
Currently the two End.DT6 implementations coexist seamlessly and can be
used depending on the context and the user preferences. So, in order to
support both versions of DT6 a new attribute (vrftable) has been
introduced which allows us to differentiate the implementation of the
behavior to be used.
A SRv6 End.DT6 legacy behavior is still instantiated using a command
like the following one:
$ ip -6 route add 2001:db8::1 encap seg6local action End.DT6 table 100 dev eth0
While to instantiate the SRv6 End.DT6 in VRF mode, the command is still
pretty straight forward:
$ ip -6 route add 2001:db8::1 encap seg6local action End.DT6 vrftable 100 dev eth0.
Obviously as in the case of SRv6 End.DT4, the VRF strict_mode parameter
must be set (net.vrf.strict_mode=1) and the VRF associated with table
100 must exist.
Please note that the instances of SRv6 End.DT6 legacy and End.DT6 VRF
mode can coexist in the same system/configuration without problems.
[1] https://tools.ietf.org/html/draft-ietf-spring-srv6-network-programming
Signed-off-by: Andrea Mayer <andrea.mayer@uniroma2.it>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
SRv6 End.DT4 is defined in the SRv6 Network Programming [1].
The SRv6 End.DT4 is used to implement IPv4 L3VPN use-cases in
multi-tenants environments. It decapsulates the received packets and it
performs IPv4 routing lookup in the routing table of the tenant.
The SRv6 End.DT4 Linux implementation leverages a VRF device in order to
force the routing lookup into the associated routing table.
To make the End.DT4 work properly, it must be guaranteed that the routing
table used for routing lookup operations is bound to one and only one
VRF during the tunnel creation. Such constraint has to be enforced by
enabling the VRF strict_mode sysctl parameter, i.e:
$ sysctl -wq net.vrf.strict_mode=1.
At JANOG44, LINE corporation presented their multi-tenant DC architecture
using SRv6 [2]. In the slides, they reported that the Linux kernel is
missing the support of SRv6 End.DT4 behavior.
The SRv6 End.DT4 behavior can be instantiated using a command similar to
the following:
$ ip route add 2001:db8::1 encap seg6local action End.DT4 vrftable 100 dev eth0
We introduce the "vrftable" extension in iproute2 in a following patch.
[1] https://tools.ietf.org/html/draft-ietf-spring-srv6-network-programming
[2] https://speakerdeck.com/line_developers/line-data-center-networking-with-srv6
Signed-off-by: Andrea Mayer <andrea.mayer@uniroma2.it>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
We introduce two callbacks used for customizing the creation/destruction of
a SRv6 behavior. Such callbacks are defined in the new struct
seg6_local_lwtunnel_ops and hereafter we provide a brief description of
them:
- build_state(...): used for calling the custom constructor of the
behavior during its initialization phase and after all the attributes
have been parsed successfully;
- destroy_state(...): used for calling the custom destructor of the
behavior before it is completely destroyed.
Signed-off-by: Andrea Mayer <andrea.mayer@uniroma2.it>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Before this patch, each SRv6 behavior specifies a set of required
attributes that must be provided by the userspace application when such
behavior is going to be instantiated. If at least one of the required
attributes is not provided, the creation of the behavior fails.
The SRv6 behavior framework lacks a way to manage optional attributes.
By definition, an optional attribute for a SRv6 behavior consists of an
attribute which may or may not be provided by the userspace. Therefore,
if an optional attribute is missing (and thus not supplied by the user)
the creation of the behavior goes ahead without any issue.
This patch explicitly differentiates the required attributes from the
optional attributes. In particular, each behavior can declare a set of
required attributes and a set of optional ones.
The semantic of the required attributes remains *totally* unaffected by
this patch. The introduction of the optional attributes does NOT impact
on the backward compatibility of the existing SRv6 behaviors.
It is essential to note that if an (optional or required) attribute is
supplied to a SRv6 behavior which does not expect it, the behavior
simply discards such attribute without generating any error or warning.
This operating mode remained unchanged both before and after the
introduction of the optional attributes extension.
The optional attributes are one of the key components used to implement
the SRv6 End.DT6 behavior based on the Virtual Routing and Forwarding
(VRF) framework. The optional attributes make possible the coexistence
of the already existing SRv6 End.DT6 implementation with the new SRv6
End.DT6 VRF-based implementation without breaking any backward
compatibility. Further details on the SRv6 End.DT6 behavior (VRF mode)
are reported in subsequent patches.
From the userspace point of view, the support for optional attributes DO
NOT require any changes to the userspace applications, i.e: iproute2
unless new attributes (required or optional) are needed.
Signed-off-by: Andrea Mayer <andrea.mayer@uniroma2.it>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Depending on the attribute (i.e.: SEG6_LOCAL_SRH, SEG6_LOCAL_TABLE, etc),
the parse() callback performs some validity checks on the provided input
and updates the tunnel state (slwt) with the result of the parsing
operation. However, an attribute may also need to reserve some additional
resources (i.e.: memory or setting up an eBPF program) in the parse()
callback to complete the parsing operation.
The parse() callbacks are invoked by the parse_nla_action() for each
attribute belonging to a specific behavior. Given a behavior with N
attributes, if the parsing of the i-th attribute fails, the
parse_nla_action() returns immediately with an error. Nonetheless, the
resources acquired during the parsing of the i-1 attributes are not freed
by the parse_nla_action().
Attributes which acquire resources must release them *in an explicit way*
in both the seg6_local_{build/destroy}_state(). However, adding a new
attribute of this type requires changes to
seg6_local_{build/destroy}_state() to release the resources correctly.
The seg6local infrastructure still lacks a simple and structured way to
release the resources acquired in the parse() operations.
We introduced a new callback in the struct seg6_action_param named
destroy(). This callback releases any resource which may have been acquired
in the parse() counterpart. Each attribute may or may not implement the
destroy() callback depending on whether it needs to free some acquired
resources.
The destroy() callback comes with several of advantages:
1) we can have many attributes as we want for a given behavior with no
need to explicitly free the taken resources;
2) As in case of the seg6_local_build_state(), the
seg6_local_destroy_state() does not need to handle the release of
resources directly. Indeed, it calls the destroy_attrs() function which
is in charge of calling the destroy() callback for every set attribute.
We do not need to patch seg6_local_{build/destroy}_state() anymore as
we add new attributes;
3) the code is more readable and better structured. Indeed, all the
information needed to handle a given attribute are contained in only
one place;
4) it facilitates the integration with new features introduced in further
patches.
Signed-off-by: Andrea Mayer <andrea.mayer@uniroma2.it>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Alexei Starovoitov says:
====================
pull-request: bpf-next 2020-12-03
The main changes are:
1) Support BTF in kernel modules, from Andrii.
2) Introduce preferred busy-polling, from Björn.
3) bpf_ima_inode_hash() and bpf_bprm_opts_set() helpers, from KP Singh.
4) Memcg-based memory accounting for bpf objects, from Roman.
5) Allow bpf_{s,g}etsockopt from cgroup bind{4,6} hooks, from Stanislav.
* https://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf-next: (118 commits)
selftests/bpf: Fix invalid use of strncat in test_sockmap
libbpf: Use memcpy instead of strncpy to please GCC
selftests/bpf: Add fentry/fexit/fmod_ret selftest for kernel module
selftests/bpf: Add tp_btf CO-RE reloc test for modules
libbpf: Support attachment of BPF tracing programs to kernel modules
libbpf: Factor out low-level BPF program loading helper
bpf: Allow to specify kernel module BTFs when attaching BPF programs
bpf: Remove hard-coded btf_vmlinux assumption from BPF verifier
selftests/bpf: Add CO-RE relocs selftest relying on kernel module BTF
selftests/bpf: Add support for marking sub-tests as skipped
selftests/bpf: Add bpf_testmod kernel module for testing
libbpf: Add kernel module BTF support for CO-RE relocations
libbpf: Refactor CO-RE relocs to not assume a single BTF object
libbpf: Add internal helper to load BTF data by FD
bpf: Keep module's btf_data_size intact after load
bpf: Fix bpf_put_raw_tracepoint()'s use of __module_address()
selftests/bpf: Add Userspace tests for TCP_WINDOW_CLAMP
bpf: Adds support for setting window clamp
samples/bpf: Fix spelling mistake "recieving" -> "receiving"
bpf: Fix cold build of test_progs-no_alu32
...
====================
Link: https://lore.kernel.org/r/20201204021936.85653-1-alexei.starovoitov@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The Multipath-TCP standard (RFC 8684) says that an MPTCP host should send
a TCP reset if the token in a MP_JOIN request is unknown.
At this time we don't do this, the 3whs completes and the 'new subflow'
is reset afterwards. There are two ways to allow MPTCP to send the
reset.
1. override 'send_synack' callback and emit the rst from there.
The drawback is that the request socket gets inserted into the
listeners queue just to get removed again right away.
2. Send the reset from the 'route_req' function instead.
This avoids the 'add&remove request socket', but route_req lacks the
skb that is required to send the TCP reset.
Instead of just adding the skb to that function for MPTCP sake alone,
Paolo suggested to merge init_req and route_req functions.
This saves one indirection from syn processing path and provides the skb
to the merged function at the same time.
'send reset on unknown mptcp join token' is added in next patch.
Suggested-by: Paolo Abeni <pabeni@redhat.com>
Cc: Eric Dumazet <edumazet@google.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
I have to now lock/unlock socket for the bind hook execution.
That shouldn't cause any overhead because the socket is unbound
and shouldn't receive any traffic.
Signed-off-by: Stanislav Fomichev <sdf@google.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Andrey Ignatov <rdna@fb.com>
Link: https://lore.kernel.org/bpf/20201202172516.3483656-3-sdf@google.com
syzkaller managed to crash the kernel using an NBMA ip6gre interface. I
could reproduce it creating an NBMA ip6gre interface and forwarding
traffic to it:
skbuff: skb_under_panic: text:ffffffff8250e927 len:148 put:44 head:ffff8c03c7a33
------------[ cut here ]------------
kernel BUG at net/core/skbuff.c:109!
Call Trace:
skb_push+0x10/0x10
ip6gre_header+0x47/0x1b0
neigh_connected_output+0xae/0xf0
ip6gre tunnel provides its own header_ops->create, and sets it
conditionally when initializing the tunnel in NBMA mode. When
header_ops->create is used, dev->hard_header_len should reflect the
length of the header created. Otherwise, when not used,
dev->needed_headroom should be used.
Fixes: eb95f52fc7 ("net: ipv6_gre: Fix GRO to work on IPv6 over GRE tap")
Cc: Maria Pasechnik <mariap@mellanox.com>
Signed-off-by: Antoine Tenart <atenart@kernel.org>
Link: https://lore.kernel.org/r/20201130161911.464106-1-atenart@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
For IPV6_2292PKTOPTIONS, do_ipv6_getsockopt() stores the user pointer
optval in the msg_control field of the msghdr.
Hence, sparse rightfully warns at ./net/ipv6/ipv6_sockglue.c:1151:33:
warning: incorrect type in assignment (different address spaces)
expected void *msg_control
got char [noderef] __user *optval
Since commit 1f466e1f15 ("net: cleanly handle kernel vs user buffers for
->msg_control"), user pointers shall be stored in the msg_control_user
field, and kernel pointers in the msg_control field. This allows to
propagate __user annotations nicely through this struct.
Store optval in msg_control_user to properly record and propagate the
memory space annotation of this pointer.
Note that msg_control_is_user is set to true, so the key invariant, i.e.,
use msg_control_user if and only if msg_control_is_user is true, holds.
The msghdr is further used in the six alternative put_cmsg() calls, with
msg_control_is_user being true, put_cmsg() picks msg_control_user
preserving the __user annotation and passes that properly to
copy_to_user().
No functional change. No change in object code.
Signed-off-by: Lukas Bulwahn <lukas.bulwahn@gmail.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/20201127093421.21673-1-lukas.bulwahn@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
True to the message of commit v5.10-rc1-105-g46d6c5ae953c, _do_
actually make use of state->sk when possible, such as in the REJECT
modules.
Reported-by: Minqiang Chen <ptpt52@gmail.com>
Cc: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: Jan Engelhardt <jengelh@inai.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Trivial conflict in CAN, keep the net-next + the byteswap wrapper.
Conflicts:
drivers/net/can/usb/gs_usb.c
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When a BPF program is used to select between a type of TCP congestion
control algorithm that uses either ECN or not there is a case where the
synack for the frame was coming up without the ECT0 bit set. A bit of
research found that this was due to the final socket being configured to
dctcp while the listener socket was staying in cubic.
To reproduce it all that is needed is to monitor TCP traffic while running
the sample bpf program "samples/bpf/tcp_cong_kern.c". What is observed,
assuming tcp_dctcp module is loaded or compiled in and the traffic matches
the rules in the sample file, is that for all frames with the exception of
the synack the ECT0 bit is set.
To address that it is necessary to make one additional call to
tcp_bpf_ca_needs_ecn using the request socket and then use the output of
that to set the ECT0 bit for the tos/tclass of the packet.
Fixes: 91b5b21c7c ("bpf: Add support for changing congestion control")
Signed-off-by: Alexander Duyck <alexanderduyck@fb.com>
Link: https://lore.kernel.org/r/160593039663.2604.1374502006916871573.stgit@localhost.localdomain
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When the TCP stack is in SYN flood mode, the server child socket is
created from the SYN cookie received in a TCP packet with the ACK flag
set.
The child socket is created when the server receives the first TCP
packet with a valid SYN cookie from the client. Usually, this packet
corresponds to the final step of the TCP 3-way handshake, the ACK
packet. But is also possible to receive a valid SYN cookie from the
first TCP data packet sent by the client, and thus create a child socket
from that SYN cookie.
Since a client socket is ready to send data as soon as it receives the
SYN+ACK packet from the server, the client can send the ACK packet (sent
by the TCP stack code), and the first data packet (sent by the userspace
program) almost at the same time, and thus the server will equally
receive the two TCP packets with valid SYN cookies almost at the same
instant.
When such event happens, the TCP stack code has a race condition that
occurs between the momement a lookup is done to the established
connections hashtable to check for the existence of a connection for the
same client, and the moment that the child socket is added to the
established connections hashtable. As a consequence, this race condition
can lead to a situation where we add two child sockets to the
established connections hashtable and deliver two sockets to the
userspace program to the same client.
This patch fixes the race condition by checking if an existing child
socket exists for the same client when we are adding the second child
socket to the established connections socket. If an existing child
socket exists, we drop the packet and discard the second child socket
to the same client.
Signed-off-by: Ricardo Dias <rdias@singlestore.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Link: https://lore.kernel.org/r/20201120111133.GA67501@rdias-suse-pc.lan
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
As pointed out by Herbert in a recent related patch, the LSM hooks do
not have the necessary address family information to use the flowi
struct safely. As none of the LSMs currently use any of the protocol
specific flowi information, replace the flowi pointers with pointers
to the address family independent flowi_common struct.
Reported-by: Herbert Xu <herbert@gondor.apana.org.au>
Acked-by: James Morris <jamorris@linux.microsoft.com>
Signed-off-by: Paul Moore <paul@paul-moore.com>
An issue was recently found where DCTCP SYN/ACK packets did not have the
ECT bit set in the L3 header. A bit of code review found that the recent
change referenced below had gone though and added a mask that prevented the
ECN bits from being populated in the L3 header.
This patch addresses that by rolling back the mask so that it is only
applied to the flags coming from the incoming TCP request instead of
applying it to the socket tos/tclass field. Doing this the ECT bits were
restored in the SYN/ACK packets in my testing.
One thing that is not addressed by this patch set is the fact that
tcp_reflect_tos appears to be incompatible with ECN based congestion
avoidance algorithms. At a minimum the feature should likely be documented
which it currently isn't.
Fixes: ac8f1710c1 ("tcp: reflect tos value received in SYN to the socket")
Signed-off-by: Alexander Duyck <alexanderduyck@fb.com>
Acked-by: Wei Wang <weiwan@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This patch adds an IPv6 routes encapsulation attribute
to the result of netlink RTM_GETROUTE requests
(i.e. ip route get 2001:db8::).
Signed-off-by: Oliver Herms <oliver.peter.herms@gmail.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Link: https://lore.kernel.org/r/20201118230651.GA8861@tws
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Currently <crypto/sha.h> contains declarations for both SHA-1 and SHA-2,
and <crypto/sha3.h> contains declarations for SHA-3.
This organization is inconsistent, but more importantly SHA-1 is no
longer considered to be cryptographically secure. So to the extent
possible, SHA-1 shouldn't be grouped together with any of the other SHA
versions, and usage of it should be phased out.
Therefore, split <crypto/sha.h> into two headers <crypto/sha1.h> and
<crypto/sha2.h>, and make everyone explicitly specify whether they want
the declarations for SHA-1, SHA-2, or both.
This avoids making the SHA-1 declarations visible to files that don't
want anything to do with SHA-1. It also prepares for potentially moving
sha1.h into a new insecure/ or dangerous/ directory.
Signed-off-by: Eric Biggers <ebiggers@google.com>
Acked-by: Ard Biesheuvel <ardb@kernel.org>
Acked-by: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
IPV6=m
NF_DEFRAG_IPV6=y
ld: net/ipv6/netfilter/nf_conntrack_reasm.o: in function
`nf_ct_frag6_gather':
net/ipv6/netfilter/nf_conntrack_reasm.c:462: undefined reference to
`ipv6_frag_thdr_truncated'
Netfilter is depending on ipv6 symbol ipv6_frag_thdr_truncated. This
dependency is forcing IPV6=y.
Remove this dependency by moving ipv6_frag_thdr_truncated out of ipv6. This
is the same solution as used with a similar issues: Referring to
commit 70b095c843 ("ipv6: remove dependency of nf_defrag_ipv6 on ipv6
module")
Fixes: 9d9e937b1c ("ipv6/netfilter: Discard first fragment not including all headers")
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Georg Kohmann <geokohma@cisco.com>
Acked-by: Pablo Neira Ayuso <pablo@netfilter.org>
Acked-by: Randy Dunlap <rdunlap@infradead.org> # build-tested
Link: https://lore.kernel.org/r/20201119095833.8409-1-geokohma@cisco.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Fix to return a negative error code from the error handling
case instead of 0, as done elsewhere in this function.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zhang Changzhong <zhangchangzhong@huawei.com>
Link: https://lore.kernel.org/r/1605581105-35295-1-git-send-email-zhangchangzhong@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Packets are processed even though the first fragment don't include all
headers through the upper layer header. This breaks TAHI IPv6 Core
Conformance Test v6LC.1.3.6.
Referring to RFC8200 SECTION 4.5: "If the first fragment does not include
all headers through an Upper-Layer header, then that fragment should be
discarded and an ICMP Parameter Problem, Code 3, message should be sent to
the source of the fragment, with the Pointer field set to zero."
The fragment needs to be validated the same way it is done in
commit 2efdaaaf88 ("IPv6: reply ICMP error if the first fragment don't
include all headers") for ipv6. Wrap the validation into a common function,
ipv6_frag_thdr_truncated() to check for truncation in the upper layer
header. This validation does not fullfill all aspects of RFC 8200,
section 4.5, but is at the moment sufficient to pass mentioned TAHI test.
In netfilter, utilize the fragment offset returned by find_prev_fhdr() to
let ipv6_frag_thdr_truncated() start it's traverse from the fragment
header.
Return 0 to drop the fragment in the netfilter. This is the same behaviour
as used on other protocol errors in this function, e.g. when
nf_ct_frag6_queue() returns -EPROTO. The Fragment will later be picked up
by ipv6_frag_rcv() in reassembly.c. ipv6_frag_rcv() will then send an
appropriate ICMP Parameter Problem message back to the source.
References commit 2efdaaaf88 ("IPv6: reply ICMP error if the first
fragment don't include all headers")
Signed-off-by: Georg Kohmann <geokohma@cisco.com>
Acked-by: Pablo Neira Ayuso <pablo@netfilter.org>
Link: https://lore.kernel.org/r/20201111115025.28879-1-geokohma@cisco.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Commit bdb7cc643f ("ipv6: Count interface receive statistics on the
ingress netdev") removed all callees for ipv6_skb_idev(). Hence, since
then, ipv6_skb_idev() is unused and make CC=clang W=1 warns:
net/ipv6/exthdrs.c:909:33:
warning: unused function 'ipv6_skb_idev' [-Wunused-function]
So, remove this unused function and a -Wunused-function warning.
Signed-off-by: Lukas Bulwahn <lukas.bulwahn@gmail.com>
Reviewed-by: Nathan Chancellor <natechancellor@gmail.com>
Link: https://lore.kernel.org/r/20201113135012.32499-1-lukas.bulwahn@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
genlmsg_cancel() needs to be called in the error path of
inet6_fill_ifmcaddr and inet6_fill_ifacaddr to cancel
the message.
Fixes: 6ecf4c37eb ("ipv6: enable IFA_TARGET_NETNSID for RTM_GETADDR")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zhang Qilong <zhangqilong3@huawei.com>
Link: https://lore.kernel.org/r/20201112080950.1476302-1-zhangqilong3@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
