The PHY driver is attached only when the driver calls
phy_connect_direct(). Calling phy_attached_print() to display
information about the PHY driver prior to that point is meaningless.
The interface can be brought down, a new PHY driver can be loaded,
and the interface then brought back up. This is the correct time
to display information about the attached driver.
Since phy_attached_print() also prints information about the
interrupt, that needs to be set as well.
Signed-off-by: Timur Tabi <timur@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The limitation to 10/100Mbit speeds on R-Car Gen3 is valid for R-Car H3
ES1.0 only. Check for the exact SoC model to allow 1Gbps on newer
revisions of R-Car H3, and on R-Car M3-W.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch enables tx and rx clock internal delay modes (TDM and RDM).
This is to address a failure in the case of 1Gbps communication using the
by salvator-x board with the KSZ9031RNX phy. This has been reported to
occur with both the r8a7795 (H3) and r8a7796 (M3-W) SoCs.
With this change APSR internal delay modes are enabled for
"rgmii-id", "rgmii-rxid" and "rgmii-txid" phy modes as follows:
phy mode | ASPR delay mode
-----------+----------------
rgmii-id | TDM and RDM
rgmii-rxid | RDM
rgmii-txid | TDM
Signed-off-by: Kazuya Mizuguchi <kazuya.mizuguchi.ks@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The macro is returning ETIME which means various checks to see if
the returned err is less than zero never work. I believe a -ETIME
should be returned instead.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The check on err < 0 is redundant and can be removed. Detected
by CoverityScan, CID#1398318 ("Logically Dead Code")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The check on err < 0 is redundant and can be removed. Detected
by CoverityScan, CID#1398321 ("Logically Dead Code")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
8000 series adapters support filtering VXLAN, NVGRE and GENEVE traffic
based on inner fields, and when the NIC recognises such traffic, it
does not match unencapsulated traffic filters any more. So add catch-
all filters for encapsulated traffic on supporting platforms.
Although recognition of VXLAN and GENEVE is based on UDP ports, and thus
will not occur until the driver (on the primary PF) notifies the
firmware of UDP ports to use, NVGRE will always be recognised, hence
without this patch 8000 series adapters will drop all NVGRE traffic.
Partly based on patches by Jon Cooper <jcooper@solarflare.com>.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rationalise several debug-or-warnings printks using netif_cond_dbg
to make output more consistent.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the NIC is switched from full-featured to low-latency, encapsulated
filters are no longer available, and this causes errors. This patch
removes those filters from the filter table on restore.
Also, if filters which are removed by the above, or which we fail to
insert when restoring filters, were UC, MC or broadcast default
filters, invalidate the corresponding vlan->default_filters entry.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
"swiotlb buffer is full" errors occur after repeated initialisation of a
device - f.e. suspend/resume or ip link set up/down. This is because memory
mapped using dma_map_single() in ravb_ring_format() and ravb_start_xmit()
is not released. Resolve this problem by unmapping descriptors when
freeing rings.
Fixes: c156633f13 ("Renesas Ethernet AVB driver proper")
Signed-off-by: Kazuya Mizuguchi <kazuya.mizuguchi.ks@renesas.com>
[simon: reworked]
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Accessing skb after submitting to input queue can cause
access to stale pointers if the skb ends up being transmitted
and freed by that time.
Signed-off-by: Satanand Burla <satananda.burla@cavium.com>
Signed-off-by: Derek Chickles <derek.chickles@cavium.com>
Signed-off-by: Raghu Vatsavayi <raghu.vatsavayi@cavium.com>
Signed-off-by: Felix Manlunas <felix.manlunas@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
PIO buffer allocation can fail for two valid reasons:
- we've run out of them (results in -ENOSPC)
- the NIC configuration doesn't support them (results in -EPERM)
Since both these failures are expected netif_err is excessive.
Signed-off-by: Bert Kenward <bkenward@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For DLMs and SLMs on 80/81/83xx, many lane configurations
across different boards are coming up. Also kernel doesn't have
any way to identify board type/info and since firmware does,
just get rid of figuring out lane to serdes config and take
whatever has been programmed by low level firmware.
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adds support to set Rx/Tx queue sizes from ethtool. Fixes
an issue with retrieving queue size. Also sets SQ's CQ_LIMIT
based on configured Tx queue size such that HW doesn't process
SQEs when there is no sufficient space in CQ.
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the binding was defined, I was not aware that mt2701 was an earlier
version of the SoC. For sake of consistency, the ethernet driver should
use mt2701 inside the compat string as this is the earliest SoC with the
ethernet core.
The ethernet driver is currently of no real use until we finish and
upstream the DSA driver. There are no users of this binding yet. It should
be safe to fix this now before it is too late and we need to provide
backward compatibility for the mt7623-eth compat string.
Reported-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
bnxt_get_port_module_status() calls bnxt_update_link() which expects
RTNL to be held. In bnxt_sp_task() that does not hold RTNL, we need to
call it with a prior call to bnxt_rtnl_lock_sp() and the call needs to
be moved to the end of bnxt_sp_task().
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
bnxt_update_link() is called from multiple code paths. Most callers,
such as open, ethtool, already hold RTNL. Only the caller bnxt_sp_task()
does not. So it is a bug to take RTNL inside bnxt_update_link().
Fix it by removing the RTNL inside bnxt_update_link(). The function
now expects the caller to always hold RTNL.
In bnxt_sp_task(), call bnxt_rtnl_lock_sp() before calling
bnxt_update_link(). We also need to move the call to the end of
bnxt_sp_task() since it will be clearing the BNXT_STATE_IN_SP_TASK bit.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In bnxt_sp_task(), we set a bit BNXT_STATE_IN_SP_TASK so that bnxt_close()
will synchronize and wait for bnxt_sp_task() to finish. Some functions
in bnxt_sp_task() require us to clear BNXT_STATE_IN_SP_TASK and then
acquire rtnl_lock() to prevent race conditions.
There are some bugs related to this logic. This patch refactors the code
to have common bnxt_rtnl_lock_sp() and bnxt_rtnl_unlock_sp() to handle
the RTNL and the clearing/setting of the bit. Multiple functions will
need the same logic. We also need to move bnxt_reset() to the end of
bnxt_sp_task(). Functions that clear BNXT_STATE_IN_SP_TASK must be the
last functions to be called in bnxt_sp_task(). The common scheme will
handle the condition properly.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This work adds a number of tracepoints to paths that are either
considered slow-path or exception-like states, where monitoring or
inspecting them would be desirable.
For bpf(2) syscall, tracepoints have been placed for main commands
when they succeed. In XDP case, tracepoint is for exceptions, that
is, f.e. on abnormal BPF program exit such as unknown or XDP_ABORTED
return code, or when error occurs during XDP_TX action and the packet
could not be forwarded.
Both have been split into separate event headers, and can be further
extended. Worst case, if they unexpectedly should get into our way in
future, they can also removed [1]. Of course, these tracepoints (like
any other) can be analyzed by eBPF itself, etc. Example output:
# ./perf record -a -e bpf:* sleep 10
# ./perf script
sock_example 6197 [005] 283.980322: bpf:bpf_map_create: map type=ARRAY ufd=4 key=4 val=8 max=256 flags=0
sock_example 6197 [005] 283.980721: bpf:bpf_prog_load: prog=a5ea8fa30ea6849c type=SOCKET_FILTER ufd=5
sock_example 6197 [005] 283.988423: bpf:bpf_prog_get_type: prog=a5ea8fa30ea6849c type=SOCKET_FILTER
sock_example 6197 [005] 283.988443: bpf:bpf_map_lookup_elem: map type=ARRAY ufd=4 key=[06 00 00 00] val=[00 00 00 00 00 00 00 00]
[...]
sock_example 6197 [005] 288.990868: bpf:bpf_map_lookup_elem: map type=ARRAY ufd=4 key=[01 00 00 00] val=[14 00 00 00 00 00 00 00]
swapper 0 [005] 289.338243: bpf:bpf_prog_put_rcu: prog=a5ea8fa30ea6849c type=SOCKET_FILTER
[1] https://lwn.net/Articles/705270/
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The first seven patches from Or Gerlitz in this series further enhances
the mlx5 SRIOV switchdev mode to support offloading IPv6 tunnels using the
TC tunnel key set (encap) and unset (decap) actions.
Or Gerlitz says:
========================
As part of doing this change, few cleanups are done in the IPv4 code,
later we move to use the full tunnel key info provided to the driver as
the key for our internal hashing which is used to identify cases where
the same tunnel is used for encapsulating multiple flows. As done in the
IPv4 case, the control path for offloading IPv6 tunnels uses route/neigh
lookups and construction of the IPv6 tunnel headers on the encap path and
matching on the outer hears in the decap path.
The last patch of the series enlarges the HW FDB size for the switchdev mode,
so it has now room to contain offloaded flows as many as min(max number
of HW flow counters supported, max HW table size supported).
========================
Next to Or's series you can find several patches handling several topics.
From Mohamad, add support for SRIOV VF min rate guarantee by using the
TSAR BW share weights mechanism.
From Or, Two patches to enable Eth VFs to query their min-inline value for
user-space.
for that we move a mlx5 low level min inline helper function from mlx5
ethernet driver into the core driver and then use it in mlx5_ib to expose
the inline mode to rdma applications through libmlx5.
From Kamal Heib, Reduce memory consumption on kdump kernel.
From Shaker Daibes, code reuse in CQE compression control logic
Thanks,
Saeed.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJYh7FNAAoJEEg/ir3gV/o+TjsIAL1e92+5eutBS9ZvhMARi+Tc
c2V9V8bG8W1RWWTvx1G0aU4nNjWsr5L8Q8gzqpwhrQITBfgpWd+hlnxQCucyhxC3
AC1qQ+AKREe/C+25D+WJRq34/61ZHEH2rbKZvpZ1O8SuicVPbcvJ9eM+wOEDxwwX
u5C5kWQ0HRtCcnFiiOYkB+0CQPH7m3+ZzZek+jDowrexHMSE+yl8ZNtaSTX9c9QN
bE2cPiCVZd7ufKPIwY8LWHBryyl7sh5P+NqzD633OeiqP/pkZsW9A+czyt+d330f
6XTKOS1PCD+TfHE0sZJT4VMCjICMHrOFbNRZuwcxJQ6NfmwIJZfskX4NLbyGQTI=
=vF7U
-----END PGP SIGNATURE-----
Merge tag 'mlx5-updates-2017-01-24' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
mlx5-updates-2017-24-01
The first seven patches from Or Gerlitz in this series further enhances
the mlx5 SRIOV switchdev mode to support offloading IPv6 tunnels using the
TC tunnel key set (encap) and unset (decap) actions.
Or Gerlitz says:
========================
As part of doing this change, few cleanups are done in the IPv4 code,
later we move to use the full tunnel key info provided to the driver as
the key for our internal hashing which is used to identify cases where
the same tunnel is used for encapsulating multiple flows. As done in the
IPv4 case, the control path for offloading IPv6 tunnels uses route/neigh
lookups and construction of the IPv6 tunnel headers on the encap path and
matching on the outer hears in the decap path.
The last patch of the series enlarges the HW FDB size for the switchdev mode,
so it has now room to contain offloaded flows as many as min(max number
of HW flow counters supported, max HW table size supported).
========================
Next to Or's series you can find several patches handling several topics.
From Mohamad, add support for SRIOV VF min rate guarantee by using the
TSAR BW share weights mechanism.
From Or, Two patches to enable Eth VFs to query their min-inline value for
user-space.
for that we move a mlx5 low level min inline helper function from mlx5
ethernet driver into the core driver and then use it in mlx5_ib to expose
the inline mode to rdma applications through libmlx5.
From Kamal Heib, Reduce memory consumption on kdump kernel.
From Shaker Daibes, code reuse in CQE compression control logic
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
If requesting msi-x interrupts fails in alx_request_irq we fall back to
a single tx queue and msi or legacy interrupts.
Currently the adapter stops working in this case and we get tx watchdog
timeouts. For reasons unknown the adapter gets confused when we load the
dma adresses to the chip in alx_init_ring_ptrs twice: the first time with
multiple queues and the second time in the fallback case with a single
queue.
To fix this move the the call to alx_reinit_rings (which calls
alx_init_ring_ptrs) after alx_request_irq. At this time it is clear how
much tx queues we have and which dma addresses we use.
Fixes: d768319cd4 ("alx: enable multiple tx queues")
Signed-off-by: Tobias Regnery <tobias.regnery@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If requesting msi-x interrupts fails we should fall back to msi or
legacy interrupts. However alx_realloc_ressources don't call
alx_init_intr, so we fail to set the right number of tx queues.
This results in watchdog timeouts and a nonfunctional adapter.
Fixes: d768319cd4 ("alx: enable multiple tx queues")
Signed-off-by: Tobias Regnery <tobias.regnery@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The condition to free the descriptor memory is wrong, we want to free the
memory if it is set and not if it is unset. Invert the test to fix this
issue.
Fixes: b0999223f224b ("alx: add ability to allocate and free alx_napi structures")
Signed-off-by: Tobias Regnery <tobias.regnery@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When using the ibmveth driver in a KVM/QEMU based VM, it currently
always prints out a scary error message like this when it is started:
ibmveth 71000003 (unregistered net_device): unable to change
checksum offload settings. 1 rc=-2 ret_attr=71000003
This happens because the driver always tries to enable the checksum
offloading without checking for the availability of this feature first.
QEMU does not support checksum offloading for the spapr-vlan device,
thus we always get the error message here.
According to the LoPAPR specification, the "ibm,illan-options" property
of the corresponding device tree node should be checked first to see
whether the H_ILLAN_ATTRIUBTES hypercall and thus the checksum offloading
feature is available. Thus let's do this in the ibmveth driver, too, so
that the error message is really only limited to cases where something
goes wrong, and does not occur if the feature is just missing.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Modify the drivers/net/ethernet/{Makefile,Kconfig} file to make them a
part of the network drivers build.
Signed-off-by: Alexander Loktionov <Alexander.Loktionov@aquantia.com>
Signed-off-by: Dmitrii Tarakanov <Dmitrii.Tarakanov@aquantia.com>
Signed-off-by: Pavel Belous <Pavel.Belous@aquantia.com>
Signed-off-by: Dmitry Bezrukov <Dmitry.Bezrukov@aquantia.com>
Signed-off-by: David M. VomLehn <vomlehn@texas.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add definitions that support receive side scaling.
Signed-off-by: Alexander Loktionov <Alexander.Loktionov@aquantia.com>
Signed-off-by: Dmitrii Tarakanov <Dmitrii.Tarakanov@aquantia.com>
Signed-off-by: Pavel Belous <Pavel.Belous@aquantia.com>
Signed-off-by: Dmitry Bezrukov <Dmitry.Bezrukov@aquantia.com>
Signed-off-by: David M. VomLehn <vomlehn@texas.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the driver interfaces required for support by the ethtool utility.
Signed-off-by: Alexander Loktionov <Alexander.Loktionov@aquantia.com>
Signed-off-by: Dmitrii Tarakanov <Dmitrii.Tarakanov@aquantia.com>
Signed-off-by: Pavel Belous <Pavel.Belous@aquantia.com>
Signed-off-by: Dmitry Bezrukov <Dmitry.Bezrukov@aquantia.com>
Signed-off-by: David M. VomLehn <vomlehn@texas.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add functions to interface with the hardware and some utility functions.
Signed-off-by: Alexander Loktionov <Alexander.Loktionov@aquantia.com>
Signed-off-by: Dmitrii Tarakanov <Dmitrii.Tarakanov@aquantia.com>
Signed-off-by: Pavel Belous <Pavel.Belous@aquantia.com>
Signed-off-by: Dmitry Bezrukov <Dmitry.Bezrukov@aquantia.com>
Signed-off-by: David M. VomLehn <vomlehn@texas.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add common functions for Atlantic hardware abstraction layer.
Signed-off-by: Alexander Loktionov <Alexander.Loktionov@aquantia.com>
Signed-off-by: Dmitrii Tarakanov <Dmitrii.Tarakanov@aquantia.com>
Signed-off-by: Pavel Belous <Pavel.Belous@aquantia.com>
Signed-off-by: Dmitry Bezrukov <Dmitry.Bezrukov@aquantia.com>
Signed-off-by: David M. VomLehn <vomlehn@texas.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add functions that handle the PCI bus interface.
Signed-off-by: Alexander Loktionov <Alexander.Loktionov@aquantia.com>
Signed-off-by: Dmitrii Tarakanov <Dmitrii.Tarakanov@aquantia.com>
Signed-off-by: Pavel Belous <Pavel.Belous@aquantia.com>
Signed-off-by: Dmitry Bezrukov <Dmitry.Bezrukov@aquantia.com>
Signed-off-by: David M. VomLehn <vomlehn@texas.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add functions to manululate the vector of receive and transmit rings.
Signed-off-by: Alexander Loktionov <Alexander.Loktionov@aquantia.com>
Signed-off-by: Dmitrii Tarakanov <Dmitrii.Tarakanov@aquantia.com>
Signed-off-by: Pavel.Belous <Pavel.Belous@aquantia.com>
Signed-off-by: Dmitry Bezrukov <Dmitry.Bezrukov@aquantia.com>
Signed-off-by: David M. VomLehn <vomlehn@texas.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add Atlantic A0 and B0 specific functions.
Signed-off-by: Alexander Loktionov <Alexander.Loktionov@aquantia.com>
Signed-off-by: Dmitrii Tarakanov <Dmitrii.Tarakanov@aquantia.com>
Signed-off-by: Pavel Belous <Pavel.Belous@aquantia.com>
Signed-off-by: Dmitry Bezrukov <Dmitry.Bezrukov@aquantia.com>
Signed-off-by: David M. VomLehn <vomlehn@texas.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for code specific to the Atlantic NIC.
Signed-off-by: Alexander Loktionov <Alexander.Loktionov@aquantia.com>
Signed-off-by: Dmitrii Tarakanov <Dmitrii.Tarakanov@aquantia.com>
Signed-off-by: Pavel Belous <Pavel.Belous@aquantia.com>
Signed-off-by: Dmitry Bezrukov <Dmitry.Bezrukov@aquantia.com>
Signed-off-by: David M. VomLehn <vomlehn@texas.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add definitions of functions that interface directly with the hardware.
Signed-off-by: Alexander Loktionov <Alexander.Loktionov@aquantia.com>
Signed-off-by: Dmitrii Tarakanov <Dmitrii.Tarakanov@aquantia.com>
Signed-off-by: Pavel.Belous <Pavel.Belous@aquantia.com>
Signed-off-by: Dmitry Bezrukov <Dmitry.Bezrukov@aquantia.com>
Signed-off-by: David M. VomLehn <vomlehn@texas.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add code to support the transmit and receive ring buffers.
Signed-off-by: Alexander Loktionov <Alexander.Loktionov@aquantia.com>
Signed-off-by: Dmitrii Tarakanov <Dmitrii.Tarakanov@aquantia.com>
Signed-off-by: Pavel Belous <Pavel.Belous@aquantia.com>
Signed-off-by: Dmitry Bezrukov <Dmitry.Bezrukov@aquantia.com>
Signed-off-by: David M. VomLehn <vomlehn@texas.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add files containing the functions and definitions used in common in
different functional areas.
Signed-off-by: Alexander Loktionov <Alexander.Loktionov@aquantia.com>
Signed-off-by: Dmitrii Tarakanov <Dmitrii.Tarakanov@aquantia.com>
Signed-off-by: Pavel Belous <Pavel.Belous@aquantia.com>
Signed-off-by: Dmitry Bezrukov <Dmitry.Bezrukov@aquantia.com>
Signed-off-by: David M. VomLehn <vomlehn@texas.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Patches to create the make and configuration files.
Signed-off-by: Alexander Loktionov <Alexander.Loktionov@aquantia.com>
Signed-off-by: Dmitrii Tarakanov <Dmitrii.Tarakanov@aquantia.com>
Signed-off-by: Pavel Belous <Pavel.Belous@aquantia.com>
Signed-off-by: Dmitry Bezrukov <Dmitry.Bezrukov@aquantia.com>
Signed-off-by: David M. VomLehn <vomlehn@texas.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
After commit 51b7b1c34e (KSZ8851-SNL: Add ethtool support for
EEPROM via eeprom_93cx6, 2011-11-21) this structure member is
unused. Delete it.
Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is intended for code reuse of mlx5e_modify_rx_cqe_compression
function.
Signed-off-by: Shaker Daibes <shakerd@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Reduce memory consumption on kdump kernel by decreasing the number of
channels to 1 and the size of RQs and SQs to the minimal values.
Signed-off-by: Kamal Heib <kamalh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
So we can use that from the IB driver too in downstream patches.
This patch doesn't change any functionality.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Add support for SRIOV VF min rate guarantee by using the TSAR BW share
weights mechanism.
The TSAR BW share vport attribute represents the weight of that vport
among the other vports weights which means that the actual vport BW
percentage is the same vport weight percentage among the total vports
weights sum.
Signed-off-by: Mohamad Haj Yahia <mohamad@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
The E-Switch FDB size was hard coded to 8k. Change it to be
min(max eswitch table size, max flow counters * num flow groups)
where the max values are read from the firmware and the number of
flow groups is hard-coded as before this change.
We don't know upfront the division of flows to group. This setup allows
each group to be of size up to the where we want to support (we mandate
pairing of flows with counters for offloading). Thus, we don't expect
multiple occurences for a group which in turn adds steering hops.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Tested-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Add the missing parts for offloading IPv6 tunnels. This includes
route and neigh lookups and construnction of the IPv6 tunnel headers.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Use more fields out of the tunnel key (e.g the tunnel source IP address)
provided by upper layers for the route lookup done on the encap offload path.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Currently we use subset of the input tunnel key fields (id, ip daddr,
dst port) which are provided by upper layers to indentify flows that should
go through the same encapsulation and maintain the HW encapsulation table.
This is redundant and can get us wrong.
Instead, keep a copy of the ip tunnel info provided by the user
through TC and have the tunnel key part as the key to our internal hash.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Move around some settings of variables as pre-step to make things
more robust and clear for the ipv6 case in down-stream patch.
This patch doesn't change any functionality.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Enhance the parsing of offloaded TC rules to set HW matching on outer
IPv6 encapsulation headers. This effectively adds support for TC tunnel
key release action (decapsulation) of SRIOV offloads over IPv6 tunnels.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
The current code is allocating the max encap size supported by
the firmware and not the size requested by the caller, fix that.
Also, spare a warning when the size of the encapsulation headers
is bigger from what is supported by the firmware.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
