This value is not calculating bytes_per_int, which would actually just
be bytes/ITR_COUNTDOWN_START, but rather it's calculating bytes/usecs.
Rename the variable for clarity so that future developers understand
what the value is actually calculating.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This work enables generic transfer of metadata from XDP into skb. The
basic idea is that we can make use of the fact that the resulting skb
must be linear and already comes with a larger headroom for supporting
bpf_xdp_adjust_head(), which mangles xdp->data. Here, we base our work
on a similar principle and introduce a small helper bpf_xdp_adjust_meta()
for adjusting a new pointer called xdp->data_meta. Thus, the packet has
a flexible and programmable room for meta data, followed by the actual
packet data. struct xdp_buff is therefore laid out that we first point
to data_hard_start, then data_meta directly prepended to data followed
by data_end marking the end of packet. bpf_xdp_adjust_head() takes into
account whether we have meta data already prepended and if so, memmove()s
this along with the given offset provided there's enough room.
xdp->data_meta is optional and programs are not required to use it. The
rationale is that when we process the packet in XDP (e.g. as DoS filter),
we can push further meta data along with it for the XDP_PASS case, and
give the guarantee that a clsact ingress BPF program on the same device
can pick this up for further post-processing. Since we work with skb
there, we can also set skb->mark, skb->priority or other skb meta data
out of BPF, thus having this scratch space generic and programmable
allows for more flexibility than defining a direct 1:1 transfer of
potentially new XDP members into skb (it's also more efficient as we
don't need to initialize/handle each of such new members). The facility
also works together with GRO aggregation. The scratch space at the head
of the packet can be multiple of 4 byte up to 32 byte large. Drivers not
yet supporting xdp->data_meta can simply be set up with xdp->data_meta
as xdp->data + 1 as bpf_xdp_adjust_meta() will detect this and bail out,
such that the subsequent match against xdp->data for later access is
guaranteed to fail.
The verifier treats xdp->data_meta/xdp->data the same way as we treat
xdp->data/xdp->data_end pointer comparisons. The requirement for doing
the compare against xdp->data is that it hasn't been modified from it's
original address we got from ctx access. It may have a range marking
already from prior successful xdp->data/xdp->data_end pointer comparisons
though.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates 2017-09-05
This series contains fixes for i40e only.
These two patches fix an issue where our nvmupdate tool does not work on RHEL 7.4
and newer kernels, in fact, the use of the nvmupdate tool on newer kernels can
cause the cards to be non-functional unless these patches are applied.
Anjali reworks the locking around accessing the NVM so that NVM acquire timeouts
do not occur which was causing the failed firmware updates.
Jake correctly updates the wb_desc when reading the NVM through the AdminQ.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
When introducing the functions to read the NVM through the AdminQ, we
did not correctly mark the wb_desc.
Fixes: 7073f46e44 ("i40e: Add AQ commands for NVM Update for X722", 2015-06-05)
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
X722 devices use the AdminQ to access the NVM, and this requires taking
the AdminQ lock. Because of this, we lock the AdminQ during
i40e_read_nvm(), which is also called in places where the lock is
already held, such as the firmware update path which wants to lock once
and then unlock when finished after performing several tasks.
Although this should have only affected X722 devices, commit
96a39aed25 ("i40e: Acquire NVM lock before reads on all devices",
2016-12-02) added locking for all NVM reads, regardless of device
family.
This resulted in us accidentally causing NVM acquire timeouts on all
devices, causing failed firmware updates which left the eeprom in
a corrupt state.
Create unsafe non-locked variants of i40e_read_nvm_word and
i40e_read_nvm_buffer, __i40e_read_nvm_word and __i40e_read_nvm_buffer
respectively. These variants will not take the NVM lock and are expected
to only be called in places where the NVM lock is already held if
needed.
Since the only caller of i40e_read_nvm_buffer() was in such a path,
remove it entirely in favor of the unsafe version. If necessary we can
always add it back in the future.
Additionally, we now need to hold the NVM lock in i40e_validate_checksum
because the call to i40e_calc_nvm_checksum now assumes that the NVM lock
is held. We can further move the call to read I40E_SR_SW_CHECKSUM_WORD
up a bit so that we do not need to acquire the NVM lock twice.
This should resolve firmware updates and also fix potential raise that
could have caused the driver to report an invalid NVM checksum upon
driver load.
Reported-by: Stefan Assmann <sassmann@kpanic.de>
Fixes: 96a39aed25 ("i40e: Acquire NVM lock before reads on all devices", 2016-12-02)
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The dynamic ITR algorithm depends on a calculation of usecs which
assumes that the interrupts have been firing constantly at the interrupt
throttle rate. This is not guaranteed because we could have a low packet
rate, or have been polling in software.
We'll estimate whether this is the case by using jiffies to determine if
we've been too long. If the time difference of jiffies is larger we are
guaranteed to have an incorrect calculation. If the time difference of
jiffies is smaller we might have been polling some but the difference
shouldn't affect the calculation too much.
This ensures that we don't get stuck in BULK latency during certain rare
situations where we receive bursts of packets that force us into NAPI
polling.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Since commit c56625d597 ("i40e/i40evf: change dynamic interrupt
thresholds") a new higher latency ITR setting called I40E_ULTRA_LATENCY
was added with a cryptic comment about how it was meant for adjusting Rx
more aggressively when streaming small packets.
This mode was attempting to calculate packets per second and then kick
in when we have a huge number of small packets.
Unfortunately, the ULTRA setting was kicking in for workloads it wasn't
intended for including single-thread UDP_STREAM workloads.
This wasn't caught for a variety of reasons. First, the ip_defrag
routines were improved somewhat which makes the UDP_STREAM test still
reasonable at 10GbE, even when dropped down to 8k interrupts a second.
Additionally, some other obvious workloads appear to work fine, such
as TCP_STREAM.
The number 40k doesn't make sense for a number of reasons. First, we
absolutely can do more than 40k packets per second. Second, we calculate
the value inline in an integer, which sometimes can overflow resulting
in using incorrect values.
If we fix this overflow it makes it even more likely that we'll enter
ULTRA mode which is the opposite of what we want.
The ULTRA mode was added originally as a way to reduce CPU utilization
during a small packet workload where we weren't keeping up anyways. It
should never have been kicking in during these other workloads.
Given the issues outlined above, let's remove the ULTRA latency mode. If
necessary, a better solution to the CPU utilization issue for small
packet workloads will be added in a future patch.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In commit 96db776a36 ("i40e/vf: fix interrupt affinity bug")
we added some code to force exit of polling in case we did
not have the correct CPU. This is important since it was possible for
the IRQ affinity to be changed while the CPU is pegged at 100%. This can
result in the polling routine being stuck on the wrong CPU until
traffic finally stops.
Unfortunately, the implementation, "if the CPU is correct, exit as
normal, otherwise, fall-through to the end-polling exit" is incredibly
confusing to reason about. In this case, the normal flow looks like the
exception, while the exception actually occurs far away from the if
statement and comment.
We recently discovered and fixed a bug in this code because we were
incorrectly initializing the affinity mask.
Re-write the code so that the exceptional case is handled at the check,
rather than having the logic be spread through the regular exit flow.
This does end up with minor code duplication, but the resulting code is
much easier to reason about.
The new logic is identical, but inverted. If we are running on a CPU not
in our affinity mask, we'll exit polling. However, the code flow is much
easier to understand.
Note that we don't actually have to check for MSI-X, because in the MSI
case we'll only have one q_vector, but its default affinity mask should
be correct as it includes all CPUs when it's initialized. Further, we
could at some point add code to setup the notifier for the non-MSI-X
case and enable this workaround for that case too, if desired, though
there isn't much gain since its unlikely to be the common case.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
On older kernels a call to irq_set_affinity_hint does not guarantee that
the IRQ affinity will be set. If nothing else on the system sets the IRQ
affinity this can result in a bug in the i40e_napi_poll() routine where
we notice that our interrupt fired on the "wrong" CPU according to our
internal affinity_mask variable.
This results in a bug where we continuously tell NAPI to stop polling to
move the interrupt to a new CPU, but the CPU never changes because our
affinity mask does not match the actual mask setup for the IRQ.
The root problem is a mismatched affinity mask value. So lets initialize
the value to cpu_possible_mask instead. This ensures that prior to the
first time we get an IRQ affinity notification we'll have the mask set
to include every possible CPU.
We use cpu_possible_mask instead of cpu_online_mask since the former is
almost certainly never going to change, while the later might change
after we've made a copy.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
If we don't have MSI-X enabled, we handle interrupts on all icr0. This
is a special case, so let's move the conditional into
i40e_update_enable_itr() in order to make i40e_napi_poll easier to
read about.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Since commit 3ffa037d7f ("i40e: Set XPS bit mask to zero in DCB mode")
we've tried to reset the XPS settings by building a custom
empty CPU mask.
This workaround is not necessary because we're not really removing the
XPS setting, but simply setting it so that no CPU is valid.
Second, we shorten the code further by using zalloc_cpumask_var instead
of a separate call to bitmap_zero().
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch fixes an issue where an error return value is
set, but without an immediate exit, the value can be overwritten
by the following code execution. The condition at this point
is not fatal, so remove the error assignment and comment the
intent for future code maintainers
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch improves the system log message. The log message will
be expanded to include the FEC mode the FW requested before link
was established.
Signed-off-by: Mariusz Stachura <mariusz.stachura@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch gives VF capability to control VLAN tag stripping via
ethtool. As rx-vlan-offload was fixed before, now the VF is able to
change it using "ethtool --offload <IF> rxvlan on/off" settings.
Signed-off-by: Mariusz Stachura <mariusz.stachura@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In new versions of GCC since 7.x a new warning exists which warns when
a string is truncated before all of the format can be completed.
When we setup VMDQ netdev names we are copying a pre-existing interface
name which could be up to 15 characters in length. Since we also add
4 bytes, v, the literal %, the d and a \0 null, we would overrun the
available size unless snprintf truncated for us.
The snprintf call will of course truncate on the end, so lets instead
modify the code to force truncation of the copied netdev name by
4 characters, to create enough space for the 4 bytes we're adding.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Albeit, we usually set true promiscuous mode for both multicast and
unicast at the same time - however, it is possible to set it
individually, so using allmulti flag which is only for allmulticast might
caused unwanted behavior in mirroring egress traffic promiscuous for
unicast in VF.
Signed-off-by: Akeem G Abodunrin <akeem.g.abodunrin@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Increase the size of the prefix buffer so that it can hold enough
characters for every possible input. Although 20 is enough for all
expected inputs, it is possible for the values to be larger than
expected, resulting in a possibly truncated string. Additionally, lets
use sizeof(prefix) in order to ensure we use the correct size if we need
to change the array length in the future.
New versions of GCC starting at 7 now include warnings to prevent
truncation unless you handle the return code. At most 27 bytes can be
written here, so lets just increase the buffer size even if for all
expected hw->bus.* values we only needed 20.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Store information about FEC modes, that were requested. It will be used
in printing link status information function and this way there is no
need to call admin queue there.
Signed-off-by: Mariusz Stachura <mariusz.stachura@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
During NVM update, state machine gets into unrecoverable state because
i40e_clean_adminq_subtask can get scheduled after the admin queue
command but before other state variables are updated. This causes
incorrect input to i40e_nvmupd_check_wait_event and state transitions
don't happen.
This fix updates the state variables so that adminq_subtask will have
accurate information whenever it gets scheduled.
Signed-off-by: Sudheer Mogilappagari <sudheer.mogilappagari@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
During NVM update, state machine gets into unrecoverable state because
i40e_clean_adminq_subtask can get scheduled after the admin queue
command but before other state variables are updated. This causes
incorrect input to i40e_nvmupd_check_wait_event and state transitions
don't happen.
This issue existed before but surfaced after commit 373149fc99
("i40e: Decrease the scope of rtnl lock")
This fix adds locking around admin queue command and update of
state variables so that adminq_subtask will have accurate information
whenever it gets scheduled.
Signed-off-by: Sudheer Mogilappagari <sudheer.mogilappagari@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently the driver allows the user to change (or even disable)
interrupt moderation if adaptive-rx/tx is enabled when this should
not be the case.
Adaptive RX/TX will not respect the user's ITR settings so
allowing the user to change it is weird. This bug would also
allow the user to disable interrupt moderation with adaptive-rx/tx
enabled which doesn't make much sense either.
This patch makes it such that if adaptive-rx/tx is enabled, the user
cannot make any manual adjustments to interrupt moderation. It also
makes it so that if ITR is disabled but adaptive-rx/tx is then
enabled, ITR will be re-enabled.
Signed-off-by: Alan Brady <alan.brady@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
According to the header file cpumask.h, we shouldn't be directly copying
a cpumask_t, since its a bitmap and might not be copied correctly. Lets
use the provided cpumask_copy() function instead.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The current name of vf_offload_flags indicates that the bitmap is
limited to offload related features. Make this more generic by renaming
it to vf_cap_flags, which allows for other capabilities besides
offloading to be added.
Signed-off-by: Stefan Assmann <sassmann@kpanic.de>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In i40e_vsi_add_vlan we treat attempting to add VID=0 as an error,
because it does not do what the caller might expect. We already special
case VID=0 in i40e_vlan_rx_add_vid so that we avoid this error when
adding the VLAN.
This special casing is necessary so that we do not add the VLAN=0 filter
since we don't want to stop receiving untagged traffic. Unfortunately,
not all callers of i40e_vsi_add_vlan are aware of this, including when
we add VLANs from a VF device.
Rather than special casing every single caller of i40e_vsi_add_vlan,
lets just move this check internally. This makes the code simpler
because the caller does not need to be aware of how VLAN=0 is special,
and we don't forget to add this check in new places.
This fixes a harmless error message displaying when adding a VLAN from
within a VF. The message was meaningless but there is no reason to
confuse end users and system administrators, and this is now avoided.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When a user gives an invalid command to change a private flag which is
not supported, either because it is read-only, or the device is not
capable of the feature, we simply ignore the request.
A naive solution would simply be to report error codes when one of the
flags was not supported. However, this causes problems because it makes
the operation not atomic. If a user requests multiple private flags
together at once we could end up changing one before failing at the
second flag.
We can do a bit better if we instead update a temporary copy of the
flags variable in the loop, and then copy it into place after. If we
aren't careful this has the pitfall of potentially silently overwriting
any changes caused by other threads.
Avoid this by using cmpxchg64 which will compare and swap the flags
variable only if it currently matched the old value. We'll report
-EAGAIN in the (hopefully rare!) case where the cmpxchg64 fails.
This ensures that we can properly report when flags are not supported in
an atomic fashion without the risk of overwriting other threads changes.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch fixes a problem with the HW ATR eviction feature where the
NVM setting was incorrect. This patch detects the issue on X720
adapters and disables the feature if the NVM setting is incorrect.
Without this patch, HW ATR Evict feature does not work on broken NVMs
and is not detected either. If the HW ATR Evict feature is disabled
the SW Eviction feature will take effect.
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Alice Michael <alice.michael@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Since commit b499ffb0a2 ("i40e: Look up MAC address in Open Firmware
or IDPROM"), we've had support for obtaining the MAC address
form Open Firmware or IDPROM.
This code relied on sending the Open Firmware address directly to the
device firmware instead of relying on our MAC/VLAN filter list. Thus,
a work around was introduced in commit b1b15df592 ("i40e: Explicitly
write platform-specific mac address after PF reset")
We refactored the Open Firmware address enablement code in the ill-named
commit 41c4c2b50d ("i40e: allow look-up of MAC address from Open
Firmware or IDPROM")
Since this refactor, we no longer even set I40E_FLAG_PF_MAC. Further, we
don't need this work around, because we actually store the MAC address
as part of the MAC/VLAN filter hash. Thus, we will restore the address
correctly upon reset.
The refactor above failed to revert the workaround, so do that now.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The number of flags found in pf->flags has grown quite large, and there
are a lot of different types of flags. Most of the flags are simply
hardware features which are enabled on some firmware or some MAC types.
Other flags are dynamic run-time flags which enable or disable certain
features of the driver.
Separate these two types of flags into pf->hw_features and pf->flags.
The hw_features list will contain a set of features which are enabled at
init time. This will not contain toggles or otherwise dynamically
changing features. These flags should not need atomic protections, as
they will be set once during init and then be essentially read only.
Everything else will remain in the flags variable. These flags may be
modified at any time during run time. A future patch may wish to convert
these flags into set_bit/clear_bit/test_bit or similar approach to
ensure atomic correctness.
The I40E_FLAG_MFP_ENABLED flag may be a good fit for hw_features but
currently is used by ethtool in the private flags settings, and thus has
been left as part of flags.
Additionally, I40E_FLAG_DCB_CAPABLE may be a good fit for the
hw_features but this patch has not tried to untangle it yet.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The X722 pf flag setup should happen before the VMDq RSS queue count is
initialized for VMDq VSI to get the right number of queues for RSS in
case of X722 devices.
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Alice Michael <alice.michael@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Now that the kernel supports double VLAN tags, we should at least play
nice. Adjust the max packet size to account for two VLAN tags, not just
one.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The UDP offload conflict is dealt with by simply taking what is
in net-next where we have removed all of the UFO handling code
entirely.
The TCP conflict was a case of local variables in a function
being removed from both net and net-next.
In netvsc we had an assignment right next to where a missing
set of u64 stats sync object inits were added.
Signed-off-by: David S. Miller <davem@davemloft.net>
Get rid of struct tc_to_netdev which is now just unnecessary container
and rather pass per-type structures down to drivers directly.
Along with that, consolidate the naming of per-type structure variables
in cls_*.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change the return value from -EINVAL to -EOPNOTSUPP. The rest of the
drivers have it like that, so be aligned.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As ndo_setup_tc is generic offload op for whole tc subsystem, does not
really make sense to have cls-specific args. So move them under
cls_common structurure which is embedded in all cls structs.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since the type is always present, push it to be a separate argument to
ndo_setup_tc. On the way, name the type enum and use it for arg type.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On 32-bit hosts and with CONFIG_DEBUG_LOCK_ALLOC we should be seeing a
lockdep splat indicating this seqcount is not correctly initialized, fix
that.
Fixes: 980e9b1186 ("i40e: Add support for 64 bit netstats")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When an administratively set MAC was previously set and should now be
switched back to 00:00:00:00:00:00 the pf_set_mac flag did not get
toggled back to false.
As a result VFs were still treated as if an administratively set MAC was
present.
Signed-off-by: Stefan Assmann <sassmann@kpanic.de>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Fill the XDP prog_id with the id just like we do in other XDP enabled
drivers such as ixgbe. This is needed so that on dump we can retrieve
the attached program based on the id, and dump BPF insns, opcodes, etc
back to user space. Only XDP driver missing this is currently i40e.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Acked-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The i40e driver attempts to display the UDP tunnel name by doing a check
against the type, where for non-zero types we use "vxlan" and for zero
type we use "geneve". This is not future proof, because if new tunnel
types get added, we'll incorrectly label them. It also depends on the
value of UDP_TUNNEL_TYPE_GENEVE == 0, which is brittle.
Instead, replace this with a function that can return a constant string
depending on the type. For now we'll use "unknown" for types we don't
know about, and we can expand this in the future if new types get added.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Compiler reported several places where driver compared
signed and unsigned types. Cast or change the types to remove
the warnings.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This just reorders some local vars and makes the code flow
clearer.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The compiler warned on an oddly indented bit of code, and when
investigating that, noted that the functions themselves had
an odd flow. The if condition was checked, and would exclude
a call to AQ, but then the aq_ret would be checked unconditionally
which just looks really weird, and is likely to cause objections.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
As it turns out there was only a small set of errors
on 32 bit, and we just needed to be using the right calls
for dealing with timespec64 variables.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
There are some rare cases where the release resource call will return an
admin Q timeout. In these cases the code needs to try to release the
resource again until it succeeds or it times out.
Signed-off-by: Paul M Stillwell Jr <paul.m.stillwell.jr@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
During certain events such as a CORER, multiple devices will run a work
task to handle some cleanup. This can cause issues due to
a single-threaded workqueue which can mean that a device doesn't cleanup
in time. Prevent this by removing the single-threaded restriction on the
module workqueue. This avoids the need to add more complex yielding
logic in our service task routine. This is also similar to what other
drivers such as fm10k do.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch fixes a problem found in systems when entering
S4 state. This patch fixes the problem by ensuring that
the misc vector's IRQ is disabled as well. Without this
patch a stack trace can be seen upon entering S4 state.
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Fix incorrect variable assignment.
Based on line 1511: aq_ret = I40_ERR_PARAM; the correct variable to be
used in this instance is aq_ret instead of ret. Also, variable ret is
updated at line 1602 just before return, so assigning a value to this
variable in this code block is useless.
Addresses-Coverity-ID: 1397693
Signed-off-by: Gustavo A R Silva <garsilva@embeddedor.com>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We recently refactored i40e_do_reset() and its friends to be able to
hold the RTNL lock only for the portions that actually need to be
protected. However, a separate refactoring added several new callers of
these functions during the PCIe error recovery and suspend/resume
cycles.
When merging the changes together, it was not noticed that we could
reduce the RTNL scope by letting the reset function handle the lock
itself, as previously it was not possible.
Fix this by replacing these call sites to indicate that the reset
function should handle its own lock. This enables multiple PFs to reset
or resume simultaneously without serializing the resets via the RTNL
lock. The end result is that on systems with lots of PFs and VFs the
resets don't stall waiting for each other to finish.
It is probable that we can also do the same for i40e_do_reset_safe, but
this author did not research that change carefully enough to be
confident.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When IWARP is enabled, we weren't clearing the PE_CRITERR, just logging
it and removing it from the mask. We need to do a corer to reset the
PE_CRITERR register, so set the bit for that as we handle the
interrupt.
We should also be checking for the error against the PFINT_ICR0 register,
and only need to clear it in the value getting written to
PFINT_ICR0_ENA.
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When disabling interrupts, we should only be clearing the CAUSE_ENA bit,
not clearing the whole register. Clearing the whole register sets the
NEXTQ_IDX field to 0 instead of 0x7ff which can confuse the Firmware in
some reset sequences.
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
There exists a bug in which the driver does not correctly exit overflow
promiscuous mode. This can occur if "too many" mac filters are added,
putting the driver into overflow promiscuous mode, and the filters are
then removed. When the failed filters are removed, the driver reports
exiting overflow promiscuous mode which is correct, however traffic
continues to be received as if in promiscuous mode still.
The bug occurs because the conditional for toggling promiscuous mode was
set to only execute when promiscuous mode was enabled and not when it
was disabled as well. This patch fixes the conditional to correctly
execute when promiscuous mode is toggled and not just enabled. Without
this patch, the driver is unable to correctly exit overflow promiscuous
mode.
Signed-off-by: Alan Brady <alan.brady@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds support for OEM firmware version. If OEM specific
adapter is detected ethtool reports OEM product version in firmware
version string instead of etrack id.
Signed-off-by: Filip Sadowski <filip.sadowski@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Partition bandwidth control is not in just one form of MFP (multi-function
partitioning), so make the code more generic and be sure to nudge the Tx
scheduler for all MFP.
Copyright updated to 2017.
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds a check and message if the device is in
MFP mode as changing RSS input set is not supported in
MFP mode.
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Changes parsing of FW 4.33 AQ command Get CEE DCBX OPER CFG (0x0A07).
Change is required because FW now creates the oper_prio_tc
nibbles reversed from those in the CEE Priority Group sub-TLV.
This change will only apply to FW 4.33 as future FW versions will use a
different function to parse the CEE data.
Signed-off-by: Greg Bowers <gregory.j.bowers@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This is a fix for the static code analysis issue where dcbcfg->numapps
could be greater than size of array (i.e dcbcfg->app[I40E_DCBX_MAX_APPS]).
The fix makes sure that the array is not accessed past the size of
of the array (i.e. I40E_DCBX_MAX_APPS).
Copyright updated to 2017.
Signed-off-by: Sudheer Mogilappagari <sudheer.mogilappagari@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The firmware expects the port number passed when setting up
the UDP tunnel configuration to be in Little Endian format.
The i40e_aq_add_udp_tunnel command byte swaps the value from
host order to Little Endian.
Since commit fe0b0cd97b ("i40e: send correct port number to
AdminQ when enabling UDP tunnels") we've correctly
sent the value in host order.
Let's also add a comment to the function explaining that it must
be in host order, as the port numbers are commonly stored as Big
Endian values.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When searching for the vf_capability client routine, dev_info() was
used, instead of the normal dev_dbg(). This causes the message to be
displayed at standard log levels which can cause administrators to
worry. Avoid this by using dev_dbg instead.
Copyright updated to 2017.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Update a few flags related to FW interactions.
Copyright updated to 2017.
Signed-off-by: Alice Michael <alice.michael@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds proper XDP_TX action support. For each Tx ring, an
additional XDP Tx ring is allocated and setup. This version does the
DMA mapping in the fast-path, which will penalize performance for
IOMMU enabled systems. Further, debugfs support is not wired up for
the XDP Tx rings.
Signed-off-by: Björn Töpel <bjorn.topel@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This commit adds basic XDP support for i40e derived NICs. All XDP
actions will end up in XDP_DROP.
Signed-off-by: Björn Töpel <bjorn.topel@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
It seems like a historic accident that these return unsigned char *,
and in many places that means casts are required, more often than not.
Make these functions (skb_put, __skb_put and pskb_put) return void *
and remove all the casts across the tree, adding a (u8 *) cast only
where the unsigned char pointer was used directly, all done with the
following spatch:
@@
expression SKB, LEN;
typedef u8;
identifier fn = { skb_put, __skb_put };
@@
- *(fn(SKB, LEN))
+ *(u8 *)fn(SKB, LEN)
@@
expression E, SKB, LEN;
identifier fn = { skb_put, __skb_put };
type T;
@@
- E = ((T *)(fn(SKB, LEN)))
+ E = fn(SKB, LEN)
which actually doesn't cover pskb_put since there are only three
users overall.
A handful of stragglers were converted manually, notably a macro in
drivers/isdn/i4l/isdn_bsdcomp.c and, oddly enough, one of the many
instances in net/bluetooth/hci_sock.c. In the former file, I also
had to fix one whitespace problem spatch introduced.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver may sleep under a spin lock, and the function call path is:
i40e_ndo_set_vf_port_vlan (acquire the lock by spin_lock_bh)
i40e_vsi_remove_pvid
i40e_vlan_stripping_disable
i40e_aq_update_vsi_params
i40e_asq_send_command
mutex_lock --> may sleep
To fixed it, the spin lock is released before "i40e_vsi_remove_pvid", and
the lock is acquired again after this function.
Signed-off-by: Jia-Ju Bai <baijiaju1990@163.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A recent commit to refactor the driver and remove the hw_disabled_flags
field accidentally introduced two regressions. First, we overwrote
pf->flags which removed various key flags including the MSI-X settings.
Additionally, it was intended that we have now two flags,
HW_ATR_EVICT_CAPABLE and HW_ATR_EVICT_ENABLED, but this was not done,
and we accidentally were mis-using HW_ATR_EVICT_CAPABLE everywhere.
This patch adds the missing piece, HW_ATR_EVICT_ENABLED, and safely
updates pf->flags instead of overwriting it.
Without this patch we will have many problems including disabling MSI-X
support, and we'll attempt to use HW ATR eviction on devices which do
not support it.
Fixes: 47994c119a ("i40e: remove hw_disabled_flags in favor of using separate flag bits", 2017-04-19)
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We need to push the chain index down to the drivers, so they have the
information to which chain the rule belongs. For now, no driver supports
multichain offload, so only chain 0 is supported. This is needed to
prevent chain squashes during offload for now. Later this will be used
to implement multichain offload.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In f8b45b74cc ("i40e/i40evf: Use build_skb to build frames")
i40e_build_skb updates the page_offset field with an incorrect offset,
which can lead to data corruption. This patch updates page_offset
correctly, by properly setting truesize.
Note that the bug only appears on architectures where PAGE_SIZE is
8192 or larger.
Fixes: f8b45b74cc ("i40e/i40evf: Use build_skb to build frames")
Signed-off-by: Björn Töpel <bjorn.topel@intel.com>
Acked-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Commit 0da36b9774 ("i40e: use DECLARE_BITMAP for state fields")
introduced changes in the way i40e works with state flags converting
them to bitmaps using kernel bitmap API. This change introduced a
regression due to a mistaken substitution using __I40E_VSI_DOWN instead
of __I40E_DOWN when testing state of a PF at i40e_reset_subtask()
function. This caused a flood in the kernel log with the follow message:
[49.013] i40e 0002:01:00.0: bad reset request 0x00000020
Commit d19cb64b92 ("i40e: separate PF and VSI state flags")
also introduced some misuse of the VSI and PF flags, so both could be
considered as the offenders.
This patch simply fixes the flags where it makes sense by changing
__I40E_VSI_DOWN to __I40E_DOWN.
Fixes: 0da36b9774 ("i40e: use DECLARE_BITMAP for state fields")
Fixes: d19cb64b92 ("i40e: separate PF and VSI state flags")
Reviewed-by: "Guilherme G. Piccoli" <gpiccoli@linux.vnet.ibm.com>
Signed-off-by: "Mauro S. M. Rodrigues" <maurosr@linux.vnet.ibm.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This moves a function that is needed for the virtchnl interface
from the i40e PF driver over to the virtchnl.h file.
It was manually verified that the function in question is unchanged
except for the function name and function header, which explains
the slight difference in the number of lines removed/added.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch implements the complete version of the virtchnl.h file
with final renames, and fixes the related code in i40e and i40evf.
It also expands comments, and adds details on the usage of
certain fields.
In addition, due to the changes a couple of casts are needed
to prevent errors found by sparse after renaming some fields.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch fixes up a bunch of whitespace issues introduced
by the previous automated change of name from i40e to virtchnl.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change updates the arguments passed to the validate function
and fixes the caller, as well as uses the new return values added to
virtchnl.h
One other minor tweak, remove a duplicate set to zero of valid_len.
This is in preparation for moving the function to virtchnl.h.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
As part of the conversion, change the arguments
to VF_IS_V1[01] macros and move them to virtchnl.h
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Before moving this function over to virtchnl.h, move
some driver specific checks that had snuck into a fairly
generic function, back into the caller of the function.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This morphs all the i40e and i40evf references to/in virtchnl.h
to be generic, using only automated methods. Updates all the
callers to use the new names. A followup patch provides separate
clean ups for messy line conversions from these "automatic"
changes, to make them more reviewable.
Was executed with the following sed script:
sed -i -f transform_script drivers/net/ethernet/intel/i40e/i40e_client.c
sed -i -f transform_script drivers/net/ethernet/intel/i40e/i40e_prototype.h
sed -i -f transform_script drivers/net/ethernet/intel/i40e/i40e_virtchnl_pf.c
sed -i -f transform_script drivers/net/ethernet/intel/i40e/i40e_virtchnl_pf.h
sed -i -f transform_script drivers/net/ethernet/intel/i40evf/i40e_common.c
sed -i -f transform_script drivers/net/ethernet/intel/i40evf/i40e_prototype.h
sed -i -f transform_script drivers/net/ethernet/intel/i40evf/i40evf.h
sed -i -f transform_script drivers/net/ethernet/intel/i40evf/i40evf_client.c
sed -i -f transform_script drivers/net/ethernet/intel/i40evf/i40evf_main.c
sed -i -f transform_script drivers/net/ethernet/intel/i40evf/i40evf_virtchnl.c
sed -i -f transform_script include/linux/avf/virtchnl.h
transform_script:
----8<----
s/I40E_VIRTCHNL_SUPPORTED_QTYPES/SAVE_ME_SUPPORTED_QTYPES/g
s/I40E_VIRTCHNL_VF_CAP/SAVE_ME_VF_CAP/g
s/I40E_VIRTCHNL_/VIRTCHNL_/g
s/i40e_virtchnl_/virtchnl_/g
s/i40e_vfr_/virtchnl_vfr_/g
s/I40E_VFR_/VIRTCHNL_VFR_/g
s/VIRTCHNL_OP_ADD_ETHER_ADDRESS/VIRTCHNL_OP_ADD_ETH_ADDR/g
s/VIRTCHNL_OP_DEL_ETHER_ADDRESS/VIRTCHNL_OP_DEL_ETH_ADDR/g
s/VIRTCHNL_OP_FCOE/VIRTCHNL_OP_RSVD/g
s/SAVE_ME_SUPPORTED_QTYPES/I40E_VIRTCHNL_SUPPORTED_QTYPES/g
s/SAVE_ME_VF_CAP/I40E_VIRTCHNL_VF_CAP/g
----8<----
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch changes the i40e driver to start using the new virtchnl
interface header file, and removes an already existing duplicate of the
i40e_virtchnl.h file contained in the i40e directory.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
If 'kzalloc' fails, a NULL pointer will be dereferenced. Return -ENOMEM
instead.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The i40e driver has logic to handle only one Tx timestamp at a time,
using a state bit lock to avoid multiple requests at once.
It may be possible, if incredibly unlikely, that a Tx timestamp event is
requested but never completes. Since we use an interrupt scheme to
determine when the Tx timestamp occurred we would never clear the state
bit in this case.
Add an i40e_ptp_tx_hang() function similar to the already existing
i40e_ptp_rx_hang() function. This function runs in the watchdog routine
and makes sure we eventually recover from this case instead of
permanently disabling Tx timestamps.
Note: there is no currently known way to cause this without hacking the
driver code to force it.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
There's no reason to pass a *vsi pointer if we already have the *pf
pointer in the only location where we call this function. Lets update
the signature and directly pass the *pf data structure pointer.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The i40e driver can only handle one Tx timestamp request at a time.
This means it is possible for an application timestamp request to be
ignored.
There is no easy way for an administrator to determine if this occurred.
Add a new statistic which tracks this, tx_hwtstamp_skipped.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The i40e driver uses a bit lock to indicate when a Tx timestamp is in
progress to avoid attempting to timestamp multiple packets at once. This
is required because hardware only has registers to handle one request at
a time.
There is a corner case where we failed to cleanup the bit lock after
a failed transmit. This can potentially result in a state bit being
locked forever.
Add some cleanup code to i40e_xmit_frame_ring to check and make sure we
cleanup incase of these failures. We also modify i40e_tx_map to return
an error code indication DMA failure.
Reported-by: Reported-by: David Mirabito <davidm@metamako.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Hardware related to the i40e driver has a limitation on Tx PTP packets.
This requires us to limit the driver to timestamping a single packet at
once. This is done using a state bitlock which enforces that only one
timestamp request is honored at a time.
Unfortunately this suffers from a race condition. The bit lock is not
cleared until after skb_tstamp_tx() is called notifying applications of
a new Tx timestamp. Even a well behaved application sending only one
packet at a time and waiting for a response can wake up and send a new
timestamped packet request before the bit lock is cleared. This results
in needlessly dropping some Tx timestamp requests.
We can fix this by unlocking the state bit as soon as we read the
Timestamp register, as this is the first point at which it is safe to
timestamp another packet.
To avoid issues with the skb pointer, we'll use a copy of the pointer
and set the global variable in the driver structure to NULL first. This
ensures that the next timestamp request does not modify our local copy
of the skb pointer.
Now, a well behaved application which has at most one outstanding
timestamp request will not accidentally race with the driver unlock bit.
Obviously an application attempting to timestamp faster than one request
at a time will have some timestamp requests skipped. Unfortunately there
is nothing we can do about that.
Reported-by: David Mirabito <davidm@metamako.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Include HWTSTAMP_FILTER_NTP_ALL in net_hwtstamp_validate() as a valid
filter and update drivers which can timestamp all packets, or which
explicitly list unsupported filters instead of using a default case, to
handle the filter.
CC: Richard Cochran <richardcochran@gmail.com>
CC: Willem de Bruijn <willemb@google.com>
Signed-off-by: Miroslav Lichvar <mlichvar@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The hw_disabled_flags field was added as a way of signifying that
a feature was automatically or temporarily disabled. However, we
actually only use this for FDir features. Replace its use with new
_AUTO_DISABLED flags instead. This is more readable, because you aren't
setting an *_ENABLED flag to *disable* the feature.
Additionally, clean up a few areas where we used these bits. First, we
don't really need to set the auto-disable flag for ATR if we're fully
disabling the feature via ethtool.
Second, we should always clear the auto-disable bits in case they somehow
got set when the feature was disabled. However, avoid displaying
a message that we've re-enabled the feature.
Third, we shouldn't be re-enabling ATR in the SB ntuple add flow,
because it might have been disabled due to space constraints. Instead,
we should just wait for the fdir_check_and_reenable to be called by the
watchdog.
Overall, this change allows us to simplify some code by removing an
extra field we didn't need, and the result should make it more clear as
to what we're actually doing with these flags.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Instead of assuming our flags fit within an unsigned long, use
DECLARE_BITMAP which will ensure that we always allocate enough space.
Additionally, use __I40E_STATE_SIZE__ markers as the last element of the
enumeration so that the size of the BITMAP is compile-time assigned
rather than programmer-time assigned. This ensures that potential future
flag additions do not actually overrun the array. This is especially
important as 32bit systems would only have 32bit longs instead of 64bit
longs as we generally have assumed in the prior code.
This change also removes a dereference of the state fields throughout
the code, so it does have a bit of code churn. The conversions were
automated using sed replacements with an alternation
s/&(vsi->back|vsi|pf)->state/\1->state/
s/&adapter->vsi.state/adapter->vsi.state/
For debugfs, we modify the printing so that we can display chunks of the
state value on new lines. This ensures that we can print the entire set
of state values. Additionally, we now print them as 08lx to ensure that
they display nicely.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Avoid using the same named flags for both vsi->state and pf->state. This
makes code review easier, as it is more likely that future authors will
use the correct state field when checking bits. Previous commits already
found issues with at least one check, and possibly others may be
incorrect.
This reduces confusion as it is more clear what each flag represents,
and which flags are valid for which state field.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The delay was added because of a desire to ensure that the VF driver can
finish up removing. However, pci_disable_sriov already has its own
ssleep() call that will sleep for an entire second, so there is no
reason to add extra delay on top of this by using msleep here. In
practice, an msleep() won't have a huge impact on timing but there is no
real value in keeping it, so lets just simplify the code and remove it.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Just as we do in i40e_reset_all_vfs, save some time when freeing VFs by
amortizing the wait time for stopping queues. We can use
i40e_vsi_stop_rings_no_wait() to begin the process of stopping all the
VF rings at once. Then, once we've started the process on each VF we can
begin waiting for the VFs to stop. This helps reduce the total wait time
by a large factor.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch corrects a major oversight in that we were not reprogramming the
ports after a reset. As a result we completely lost all of the Rx tunnel
offloads on receive including Rx checksum, RSS on inner headers, and ATR.
The fix for this is pretty standard as all we needed to do is reset the
filter bits to pending for all active filters and schedule the sync event.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The .index field of i40e_udp_port_config represents the udp port number.
Rename this variable to port so that it is more obvious.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When allocating a large number of VFs, the driver previously used
i40e_reset_vf in a sequence. Just as when performing a normal reset,
this accumulates a large amount of delay for handling all of the VFs in
sequence. This delay is mainly due to a hardware requirement to wait
after initiating a reset on the VF.
We recently added a new function, i40e_reset_all_vfs() which can be used
to amortize the delay time, by first triggering all VF resets, then
waiting once, and finally cleaning up and allocating the VFs. This is
almost as good as truly running the resets in parallel.
In order to avoid sending a spurious reset message to a client
interface, we have a check to see whether we've assigned
pf->num_alloc_vfs yet. This was originally intended as a way to
distinguish the "initialization" case from the regular reset case.
Unfortunately, this means that we can't directly use i40e_reset_all_vfs
yet. Lets avoid this check of pf->num_alloc_vfs by replacing it with
a proper VSI state bit which we can use instead. This makes the
intention much clearer and allows us to re-use the i40e_reset_all_vfs
function directly.
Change-ID: I694279b37eb6b5a91b6670182d0c15d10244fd6e
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
These flags represent the state of the VF at various times. Do not
spell them as _STAT_ which can be confusing to readers who may think
these refer to statistics.
Change-ID: I6bc092cd472e8276896a1fd7498aced2084312df
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This state bit was added as a way for DCB to avoid having to wait for
the queues to disable when handling LLDP events. The logic for this was
burried deep within stop Tx and stop Rx queue code. First, let's rename
it so that it does not appear to only affect Tx when infact it modifies
both Tx and Rx flow. Second we can move it up into the i40e_stop_rings()
function, and we can simply re-use the i40e_stop_rings_no_wait() so that
we don't have to bury the implementation as deep into the call stack.
An alternative might be to remove the state bit and instead attempt to
shut down everything directly in DCP flow. This, however, is not ideal
because it creates yet another separate shutdown routine that we'd have
to maintain. In the current implementation any changes will be made to
both flows.
Change-ID: I68e1ccb901af320862bca395e9c9746f08e8b17c
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When there are a lot of active VFs, it can take multiple seconds to
finish resetting all of them during certain flows., which can cause some
VFs to fail to wait long enough for the reset to occur. The user might
see messages like "Never saw reset" or "Reset never finished" and the VF
driver will stop functioning properly.
The naive solution would be to simply increase the wait timer. We can
get much more clever. Notice that i40e_reset_vf is run in a serialized
fashion, and includes lots of delays.
There are two prominent delays which take most of the time. First, when
we begin resetting VFs, we have multiple 10ms delays which accrue
because we reset each VF in a serial fashion. These delays accumulate to
almost 4 seconds when handling the maximum number of VFs (128).
Secondly, there is a massive 50ms delay for each time we disable queues
on a VSI. This delay is necessary to allow HW to finish disabling queues
before we restore functionality. However, just like with the first case,
we are paying the cost for each VF, rather than disabling all VFs and
waiting once.
Both of these can be fixed, but required some previous refactoring to
handle the special case. First, we will need the
i40e_vsi_wait_queues_disabled function which was previously DCB
specific. Second, we will need to implement our own
i40e_vsi_stop_rings_no_wait function which will handle the stopping of
rings without the delays.
Finally, implement an i40e_reset_all_vfs function, which will first
start the reset of all VFs, and pay the wait cost all at once, rather
than serially waiting for each VF before we start processing then next
one. After the VF has been reset, we'll disable all the VF queues, and
then wait for them to disable. Again, we'll organize the flow such that
we pay the wait cost only once.
Finally, after we've disabled queues we'll go ahead and begin restoring
VF functionality. The result is reducing the wait time by a large factor
and ensuring that VFs do not timeout when waiting in the VF driver.
Change-ID: Ia6e8cf8d98131b78aec89db78afb8d905c9b12be
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
A future patch is going to want to re-use some of the code in
i40e_reset_vf, so lets break up the beginning and ending parts into
their own helper functions. The first function will be used to
initialize the reset on a VF, while the second function will be used to
finalize the reset and restore functionality.
Change-ID: I48df808b8bf09de3c2ed8c521f57b3f0ab9e5907
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When sending an adminq command, we wait for the command to complete in
a loop. This loop waits for an entire millisecond, when in practice the
adminq command is processed often much faster.
Change the loop to use i40e_usec_delay instead, and wait for 50 usecs
each time instead. This appears to be about the minimum time required,
based on some manual observation and testing.
The primary benefit of this change is reducing latency of various
operations in the PF driver, especially when related to having a large
number of VFs enabled.
For example, on Linux, when instantiating 128 VFs, the time to finish
the operation dropped from about 9 seconds down to under 6 seconds.
Additionally, the time it takes to finish a PF reset with 128 VFs
dropped from 5.1 seconds down to 0.7 seconds.
As the examples above show, a significant portion of the delay is wasted
waiting for admiqn operations which have already finished.
This patch shouldn't cause impact to functionality, as we still check
and keep waiting until the command does get processed. The only expected
change is an increase in CPU utilization as we now check for completion
far more times. However, in practice the commands appear to generally be
complete within the first delay window anyways.
Change-ID: If8af8388e100da0a14eaf9e1af3afadf73a958cf
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The check for I40E_CONFIG_BUSY state bit in the i40e_set_link_ksettings
function is fishy. First we can notice a few things about the check here.
First a similar check was introduced by commit
'c7d05ca89f8e ("i40e: driver ethtool core")'
Later a commit introducing the link settings was added by commit
'bf9c71417f72 ("i40e: Implement set_settings for ethtool")'
However, this second check was against vsi->state instead of pf->state,
and also failed to set the bit, it only checks. That indicates the locking
was not quite correct. The only other place that the state bit
in vsi->state gets used is to protect the filter list.
Since this code does not care about the mac filter list, and seems
clear the original code should have set the pf->state bit. Fix these
issues by using pf->state correctly, and by actually setting the bit
so that we properly lock as expected.
Since these checks occur while holding the rtnl_lock(), lets also add a
timeout so that we don't potentially softlock the system.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
A future patch will need to be able to handle controlling queues without
waiting until all VSIs are handled. Factor out the direct queue
modification so that we can easily re-use this code. The result is also
a bit easier to read since we don't embed multiple single-letter loop
counters.
Change-ID: Id923cbfa43127b1c24d8ed4f809b1012c736d9ac
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We made some effort to reduce the RTNL lock scope when resetting and
rebuilding the PF. Unfortunately we still held the RTNL lock during the
VF reset operation, which meant that multiple PFs could not reset in
parallel due to the global lock. For now, further reduce the scope by
not holding the RTNL lock while resetting VFs. This allows multiple PFs
to reset in a timely manner.
Change-ID: I2fbf823a0063f24dff67676cad09f0bbf83ee4ce
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
