In case of error, the function devm_ioremap() returns NULL pointer
not ERR_PTR(). The IS_ERR() test in the return value check should
be replaced with NULL test.
Fixes: 0af65b9b91 ("remoteproc: qcom: wcss: Add non pas wcss Q6 support for QCS404")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Link: https://lore.kernel.org/r/20210319094100.4185044-1-weiyongjun1@huawei.com
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The PRU firmware interrupt mappings are configured and unconfigured in
.start() and .stop() callbacks respectively using the variables 'evt_count'
and a 'mapped_irq' pointer. These variables are modified only during these
callbacks but are not re-initialized/reset properly during unwind or
failure paths. These stale values caused a kernel crash while stopping a
PRU remoteproc running a different firmware with no events on a subsequent
run after a previous run that was running a firmware with events.
Fix this crash by ensuring that the evt_count is 0 and the mapped_irq
pointer is set to NULL in pru_dispose_irq_mapping(). Also, reset these
variables properly during any failures in the .start() callback. While
at this, the pru_dispose_irq_mapping() callsites are all made to look
the same, moving any conditional logic to inside the function.
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Fixes: c75c9fdac6 ("remoteproc: pru: Add support for PRU specific interrupt configuration")
Reported-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Suman Anna <s-anna@ti.com>
Link: https://lore.kernel.org/r/20210407155641.5501-4-s-anna@ti.com
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The irq_create_fwspec_mapping() returns a proper virq value on success
and 0 upon any failure. The pru_handle_intrmap() treats this as an error
and disposes all firmware event mappings correctly, but is returning
this incorrect value as is, letting the pru_rproc_start() interpret it
as a success and boot the PRU.
Fix this by returning an error value back upon any such failure. While
at this, revise the error trace to print some meaningful info about the
failed event.
Fixes: c75c9fdac6 ("remoteproc: pru: Add support for PRU specific interrupt configuration")
Signed-off-by: Suman Anna <s-anna@ti.com>
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Link: https://lore.kernel.org/r/20210407155641.5501-3-s-anna@ti.com
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The PRU firmware interrupt mapping logic in pru_handle_intrmap() uses
of_irq_find_parent() with PRU device node to get a handle to the PRUSS
Interrupt Controller at present. This logic however requires that the
PRU nodes always define a interrupt-parent property. This property is
neither a required/defined property as per the PRU remoteproc binding,
nor is relevant from a DT node point of view without any associated
interrupts. The current logic finds a wrong interrupt controller and
fails to perform proper mapping without any interrupt-parent property
in the PRU nodes.
Fix this logic to always find and use the sibling interrupt controller.
Also, while at this, fix the acquired interrupt controller device node
reference properly.
Fixes: c75c9fdac6 ("remoteproc: pru: Add support for PRU specific interrupt configuration")
Signed-off-by: Suman Anna <s-anna@ti.com>
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Link: https://lore.kernel.org/r/20210407155641.5501-2-s-anna@ti.com
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Introduce a firmware-name property, in order to be able to support
device/platform specific firmware for the wireless connectivity
subsystem; in line with other Qualcomm remoteproc drivers.
Acked-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210312002441.3273183-1-bjorn.andersson@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Q6 based WiFi fw loading is supported across
different targets, ex: IPQ8074/QCS404. In order to
support different fw names/pas id etc, populate
hardcoded param using driver data.
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Signed-off-by: Gokul Sriram Palanisamy <gokulsri@codeaurora.org>
Link: https://lore.kernel.org/r/1611859695-11824-2-git-send-email-gokulsri@codeaurora.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Refactor function rproc_cdev_release() to take into account the
current state of the remote processor when choosing the state to
transition to.
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Link: https://lore.kernel.org/r/20210312162453.1234145-18-mathieu.poirier@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
This patch introduces the capability to detach a remote processor
that has been attached to by the remoteproc core. For that to happen
a rproc::ops::detach() operation needs to be available.
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Reviewed-by: Arnaud Pouliquen <arnaud.pouliquen@st.com>
Link: https://lore.kernel.org/r/20210312162453.1234145-17-mathieu.poirier@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Allow a remote processor that was started by another entity to be
switched off by the remoteproc core. For that to happen a
rproc::ops::stop() operation needs to be available.
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Reviewed-by: Arnaud Pouliquen <arnaud.pouliquen@st.com>
Link: https://lore.kernel.org/r/20210312162453.1234145-16-mathieu.poirier@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
This patch takes into account scenarios where a remote processor
has been attached to when receiving a "start" command from sysfs.
As with the case with the running state, the command can't be
carried out if the remote processor is already in operation.
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Reviewed-by: Arnaud Pouliquen <arnaud.pouliquen@st.com>
Link: https://lore.kernel.org/r/20210312162453.1234145-15-mathieu.poirier@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The panic handler operation of registered remote processors
should also be called when remote processors have been
attached to.
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Arnaud Pouliquen <arnaud.pouliquen@st.com>
Link: https://lore.kernel.org/r/20210312162453.1234145-14-mathieu.poirier@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
When a remote processor that was attached to is stopped, special care
must be taken to make sure the shutdown process is similar to what
it would be had it been started by the remoteproc core.
This patch takes care of that by making a copy of the resource
table currently used by the remote processor. From that point on
the copy is used, as if the remote processor had been started by
the remoteproc core.
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Reviewed-by: Arnaud Pouliquen <arnaud.pouliquen@st.com>
Reported-by: kernel test robot <lkp@intel.com>
Link: https://lore.kernel.org/r/20210312162453.1234145-13-mathieu.poirier@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
If it is possible to detach the remote processor, keep an untouched
copy of the resource table. That way we can start from the same
resource table without having to worry about original values or what
elements the startup code has changed when re-attaching to the remote
processor.
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Reviewed-by: Arnaud Pouliquen <arnaud.pouliquen@st.com>
Link: https://lore.kernel.org/r/20210312162453.1234145-12-mathieu.poirier@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Introduce function rproc_detach() to enable the remoteproc
core to release the resources associated with a remote processor
without stopping its operation.
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Reviewed-by: Arnaud Pouliquen <arnaud.pouliquen@st.com>
Link: https://lore.kernel.org/r/20210312162453.1234145-11-mathieu.poirier@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Introduce function __rproc_detach() to perform the same kind of
operation as rproc_stop(), but instead of switching off the
remote processor using rproc->ops->stop(), it uses
rproc->ops->detach(). That way it is possible for the core
to release the resources associated with a remote processor while
the latter is kept operating.
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Arnaud Pouliquen <arnaud.pouliquen@st.com>
Link: https://lore.kernel.org/r/20210312162453.1234145-10-mathieu.poirier@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Some actions such as memory resources reallocation are needed when
trying to reattach a co-processor. Use the prepare() operation for
these actions.
Co-developed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Arnaud POULIQUEN <arnaud.pouliquen@foss.st.com>
Link: https://lore.kernel.org/r/20210312162453.1234145-8-mathieu.poirier@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Move the setting of the resource table installed by an external
entity to rproc_ops::get_loaded_rsc_table(). This is to support
scenarios where a remote processor has been attached to but is
detached at a later stage. To re-attach the remote processor,
the address of the resource table needs to be available
at a later time than the platform driver's probe() function.
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Reviewed-by: Arnaud Pouliquen <arnaud.pouliquen@st.com>
Link: https://lore.kernel.org/r/20210312162453.1234145-7-mathieu.poirier@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Add a new get_loaded_rsc_table() operation in order to support
scenarios where the remoteproc core has booted a remote processor
and detaches from it. When re-attaching to the remote processor,
the core needs to know where the resource table has been placed
in memory.
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Reviewed-by: Arnaud Pouliquen <arnaud.pouliquen@st.com>
Link: https://lore.kernel.org/r/20210312162453.1234145-6-mathieu.poirier@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
There is a need to know when a remote processor has been attached
to rather than booted by the remoteproc core. In order to avoid
manipulating two variables, i.e rproc::autonomous and
rproc::state, get rid of the former and simply use the newly
introduced RPROC_ATTACHED state.
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Arnaud Pouliquen <arnaud.pouliquen@st.com>
Link: https://lore.kernel.org/r/20210312162453.1234145-5-mathieu.poirier@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Add a new RPROC_ATTACHED state to take into account scenarios
where the remoteproc core needs to attach to a remote processor
that is booted by another entity.
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Arnaud Pouliquen <arnaud.pouliquen@st.com>
Link: https://lore.kernel.org/r/20210312162453.1234145-4-mathieu.poirier@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Rename function rproc_actuate() to rproc_attach(). That way it is
easy to understand that it does the opposite of rproc_detach().
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Arnaud Pouliquen <arnaud.pouliquen@st.com>
Link: https://lore.kernel.org/r/20210312162453.1234145-3-mathieu.poirier@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Whether started at probe() time or thereafter from the command
line, a remote processor needs to be shut down before the final
cleanup phases can happen. Otherwise the system may be left in
an unpredictable state where the remote processor is expecting
the remoteproc core to be providing services when in fact it
no longer exist.
Invariably calling rproc_shutdown() is fine since it will return
immediately if the remote processor has already been switched
off.
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Arnaud Pouliquen <arnaud.pouliquen@st.com>
Link: https://lore.kernel.org/r/20210312162453.1234145-2-mathieu.poirier@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Analog to the issue in the common mdt_loader code the MSS ELF loader
does not validate that p_filesz bytes will fit in the memory region and
that the loaded segments are not truncated. Fix this in the same way
as proposed for the mdt_loader.
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Fixes: 135b9e8d1c ("remoteproc: qcom_q6v5_mss: Validate modem blob firmware size before load")
Link: https://lore.kernel.org/r/20210312232002.3466791-1-bjorn.andersson@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Failing to read the "firmware-name" DT property without informing the
developer is annoying, add some helpful debug prints.
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Link: https://lore.kernel.org/r/20210312002605.3273255-1-bjorn.andersson@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The K3 PRUs are 32-bit processors and in general have some limitations
in using the standard ARMv8 memcpy function for loading firmware segments,
so the driver already uses a custom memcpy implementation. This added
logic however is limited to only IRAMs at the moment, but the loading
into Data RAMs is not completely ok either and does generate a kernel
crash for unaligned accesses.
Fix these crashes by removing the existing IRAM logic limitation and
extending the custom memcpy usage to Data RAMs as well for all K3 SoCs.
Fixes: 1d39f4d199 ("remoteproc: pru: Add support for various PRU cores on K3 AM65x SoCs")
Signed-off-by: Suman Anna <s-anna@ti.com>
Link: https://lore.kernel.org/r/20210315205859.19590-1-s-anna@ti.com
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
In case of error, the function devm_ioremap() returns NULL pointer
not ERR_PTR(). The IS_ERR() test in the return value check should
be replaced with NULL test.
Fixes: ecadcc4749 ("remoteproc: imx_rproc: use devm_ioremap")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Link: https://lore.kernel.org/r/20210312080420.277151-1-weiyongjun1@huawei.com
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Use virtio/mailbox to build connection between Remote Proccessors
and Linux. Add work queue to handle incoming messages.
Reviewed-by: Richard Zhu <hongxing.zhu@nxp.com>
Reviewed-by: Mathieu Poirier <mathieu.poirer@linaro.org>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Link: https://lore.kernel.org/r/1615029865-23312-11-git-send-email-peng.fan@oss.nxp.com
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
vdev regions are vdev0vring0, vdev0vring1, vdevbuffer and similar.
They are handled by remoteproc common code, no need to map in imx
rproc driver.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Link: https://lore.kernel.org/r/1615029865-23312-10-git-send-email-peng.fan@oss.nxp.com
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The hook is used to parse memory-regions and load resource table
from the address the remote processor published.
Reviewed-by: Richard Zhu <hongxing.zhu@nxp.com>
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Link: https://lore.kernel.org/r/1615029865-23312-8-git-send-email-peng.fan@oss.nxp.com
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
We might need to map an region multiple times, becaue the region might
be shared between remote processors, such i.MX8QM with dual M4 cores.
So use devm_ioremap, not devm_ioremap_resource.
Reviewed-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Richard Zhu <hongxing.zhu@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Link: https://lore.kernel.org/r/1615029865-23312-7-git-send-email-peng.fan@oss.nxp.com
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
It is using devm_ioremap, so not devm_ioremap_resource. Correct
the error message and print out sa/size.
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Link: https://lore.kernel.org/r/1615029865-23312-6-git-send-email-peng.fan@oss.nxp.com
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Introduce an extra parameter is_iomem to da_to_va, then the caller
could take the memory as normal memory or io mapped memory.
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Link: https://lore.kernel.org/r/1615029865-23312-5-git-send-email-peng.fan@oss.nxp.com
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
There are four different callback functions that are used for the
rproc_handle_resource_t callback that all have different second
parameter types.
rproc_handle_vdev -> struct fw_rsc_vdev
rproc_handle_trace -> struct fw_rsc_trace
rproc_handle_devmem -> struct fw_rsc_devmem
rproc_handle_carveout -> struct fw_rsc_carveout
These callbacks are cast to rproc_handle_resource_t so that there is no
error about incompatible pointer types. Unfortunately, this is a Clang's
Control-Flow Integrity checking violation, which verifies that the
callback function's types match the prototypes exactly before jumping.
[ 7.275750] Kernel panic - not syncing: CFI failure (target: rproc_handle_vdev+0x0/0x4)
[ 7.283763] CPU: 2 PID: 1 Comm: init Tainted: G C O 5.4.70-03301-g527af2c96672 #17
[ 7.292463] Hardware name: NXP i.MX8MPlus EVK board (DT)
[ 7.297779] Call trace:
[ 7.300232] dump_backtrace.cfi_jt+0x0/0x4
[ 7.304337] show_stack+0x18/0x24
[ 7.307660] dump_stack+0xb8/0x114
[ 7.311069] panic+0x164/0x3d4
[ 7.314130] __ubsan_handle_cfi_check_fail_abort+0x0/0x14
[ 7.319533] perf_proc_update_handler+0x0/0xcc
[ 7.323983] __cfi_check+0x63278/0x6a290
[ 7.327913] rproc_boot+0x3f8/0x738
[ 7.331404] rproc_add+0x68/0x110
[ 7.334738] imx_rproc_probe+0x5e4/0x708 [imx_rproc]
[ 7.339711] platform_drv_probe+0xac/0xf0
[ 7.343726] really_probe+0x260/0x65c
[ 7.347393] driver_probe_device+0x64/0x100
[ 7.351580] device_driver_attach+0x6c/0xac
[ 7.355766] __driver_attach+0xdc/0x184
[ 7.359609] bus_for_each_dev+0x98/0x104
[ 7.363537] driver_attach+0x24/0x30
[ 7.367117] bus_add_driver+0x100/0x1e0
[ 7.370958] driver_register+0x78/0x114
[ 7.374800] __platform_driver_register+0x44/0x50
[ 7.379514] init_module+0x20/0xfe8 [imx_rproc]
[ 7.384049] do_one_initcall+0x190/0x348
[ 7.387979] do_init_module+0x5c/0x210
[ 7.391731] load_module+0x2fbc/0x3590
[ 7.395485] __arm64_sys_finit_module+0xb8/0xec
[ 7.400025] el0_svc_common+0xb4/0x19c
[ 7.403777] el0_svc_handler+0x74/0x98
[ 7.407531] el0_svc+0x8/0xc
[ 7.410419] SMP: stopping secondary CPUs
[ 7.414648] Kernel Offset: disabled
[ 7.418142] CPU features: 0x00010002,2000200c
[ 7.422501] Memory Limit: none
To fix this, change the second parameter of all functions to void * and
use a local variable with the correct type so that everything works
properly. With this, we can remove casting to rproc_handle_resource_t
for these functions.
Signed-off-by: Jindong Yue <jindong.yue@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Sami Tolvanen <samitolvanen@google.com>
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Link: https://lore.kernel.org/r/20210224055825.7417-1-jindong.yue@nxp.com
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Fix the following coccicheck warning:
./drivers/remoteproc/pru_rproc.c:247:0-23: WARNING:
pru_rproc_debug_ss_fops should be defined with DEFINE_DEBUGFS_ATTRIBUTE
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Yang Li <yang.lee@linux.alibaba.com>
Link: https://lore.kernel.org/r/1614154829-42461-1-git-send-email-yang.lee@linux.alibaba.com
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
PRU port of GNU Binutils lacks support for separate address spaces.
PRU IRAM addresses are marked with artificial offset to differentiate
them from DRAM addresses. Hence remoteproc must mask IRAM addresses
coming from GNU ELF in order to get the true hardware address.
PRU firmware used for testing was the example in:
https://github.com/dinuxbg/pru-gcc-examples/tree/master/blinking-led/pru
Signed-off-by: Dimitar Dimitrov <dimitar@dinux.eu>
Link: https://lore.kernel.org/r/20201230105005.30492-1-dimitar@dinux.eu
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
On 32-bit machines with 64-bit resource_size_t, the driver causes
a link failure because of the 64-bit division:
arm-linux-gnueabi-ld: drivers/remoteproc/qcom_pil_info.o: in function `qcom_pil_info_store':
qcom_pil_info.c:(.text+0x1ec): undefined reference to `__aeabi_uldivmod'
Add a cast to an u32 to avoid this. If the resource exceeds 4GB,
there are bigger problems.
Fixes: 549b67da66 ("remoteproc: qcom: Introduce helper to store pil info in IMEM")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20210103135628.3702427-1-arnd@kernel.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
rproc_alloc_firmware() (called by rproc_alloc()) can allocate
rproc->firmware using kstrdup_const() and therefore should be freed
using kfree_const(); however, rproc_set_firmware() frees it using the
simple kfree(). This causes a kernel oops if a constant string is passed
to rproc_alloc() and rproc_set_firmware() is subsequently called.
Fix the above issue by using kfree_const() to free rproc->firmware in
rproc_set_firmware().
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Daniele Alessandrelli <daniele.alessandrelli@intel.com>
Link: https://lore.kernel.org/r/20210118165904.719999-1-daniele.alessandrelli@linux.intel.com
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
L1TCM is a high performance memory region in MT8192 SCP.
Reads L1TCM memory region from DTS to determine if the machine supports.
Loads L1TCM memory region to SCP sys if the firmware provides.
Starts from MT8192 SCP, the firmware contains physical addresses for
each memory region, for instance:
Program Headers:
Type Offset VirtAddr PhysAddr FileSiz MemSiz Flg Align
LOAD 0xXXXXXX 0xXXXXXXXX 0x10500000 0xXXXXX 0xXXXXX XXX 0xXXXX
LOAD 0xXXXXXX 0xXXXXXXXX 0x10700000 0xXXXXX 0xXXXXX XXX 0xXXXX
LOAD 0xXXXXXX 0xXXXXXXXX 0x50000000 0xXXXXX 0xXXXXX XXX 0xXXXX
Kernel driver can use the "PhysAddr" (i.e. da in the da_to_va callbacks)
to know the ELF segment belongs to which region.
To backward compatible to MT8183 SCP, separates the da_to_va callbacks
for new and legacy version.
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Tzung-Bi Shih <tzungbi@google.com>
Link: https://lore.kernel.org/r/20210127083136.3745652-5-tzungbi@google.com
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The register MT8192_CORE0_MEM_ATT_PREDEF contains attributes for each
memory region. It defines whether a memory region can be managed by MPU
or not.
In the past, due to the default settings in the register, MT8192 SCP
works luckily. After enabling L1TCM, SCP starts to access memory region
that is not included in the default settings. As a result, SCP hangs.
Enables MPU for all memory regions in MT8192 SCP.
Note that the register is read only once when SCP resets. Thus, it must
be set from kernel side.
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Tzung-Bi Shih <tzungbi@google.com>
Link: https://lore.kernel.org/r/20210127083136.3745652-3-tzungbi@google.com
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Replaces platform_get_resource_byname() and devm_ioremap_resource()
pairs to devm_platform_ioremap_resource_byname().
Note that, not every pairs are applicable to replace. Especially when
it needs to access the resource struct from
platform_get_resource_byname().
For example:
scp->sram_size = resource_size(res);
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Tzung-Bi Shih <tzungbi@google.com>
Link: https://lore.kernel.org/r/20210127083136.3745652-2-tzungbi@google.com
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Add a 'auto_boot' module parameter that instructs the remoteproc driver
whether or not it should auto-boot the remote processor, which will
default to "false", since the VPU in Ingenic SoCs does not really have
any predetermined function.
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Link: https://lore.kernel.org/r/20210123142956.17865-1-paul@crapouillou.net
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Building the remoteproc drivers into the kernel while the qcom_glink
code is in a loadable module results in a link error:
ld.lld: error: undefined symbol: qcom_glink_ssr_notify
>>> referenced by vmlinux.o:(glink_subdev_unprepare)
Add a Kconfig dependency to avoid this.
Reviewed-by: Alex Elder <elder@linaro.org>
Fixes: 8527efc59d ("rpmsg: glink: Guard qcom_glink_ssr_notify() with correct config")
Fixes: 5d1f2e3c80 ("soc: qcom: glink_ssr: Internalize ssr_notifiers")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20210204154010.1585457-1-arnd@kernel.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
When possible use dev_err_probe help to properly deal with the
PROBE_DEFER error.
The benefit is that DEFER issue will be logged in the devices_deferred
debugfs file.
Signed-off-by: Arnaud Pouliquen <arnaud.pouliquen@foss-st.com>
Link: https://lore.kernel.org/r/20201217144125.12903-1-arnaud.pouliquen@foss.st.com
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
With these more help text added, hopefully it's easier to understand the
distinctions of these qcom remoteproc drivers.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Link: https://lore.kernel.org/r/20201217030400.6235-1-shawn.guo@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
WCN3660B is a variant of WCN3660, but with the same regulator
requirements as WCN3620/WCN3680. As far as qcom_wcnss_iris is
concerned we can just use qcom,wcn3680 (wcn3680_data).
However, a separate compatible is needed for WCN3660B because
the wcn36xx driver uses it to enable chip-specific functionality.
In particular, it enables 802.11ac for qcom,wcn3680 which is not
supported by WCN3660B.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20210106102134.59801-3-stephan@gerhold.net
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
There are a couple of subsystems maintained by other people that
merge their drivers through the SoC tree, those changes include:
- The SCMI firmware framework gains support for sensor notifications
and for controlling voltage domains.
- A large update for the Tegra memory controller driver, integrating
it better with the interconnect framework
- The memory controller subsystem gains support for Mediatek MT8192
- The reset controller framework gains support for sharing pulsed
resets
For Soc specific drivers in drivers/soc, the main changes are
- The Allwinner/sunxi MBUS gets a rework for the way it handles
dma_map_ops and offsets between physical and dma address spaces.
- An errata fix plus some cleanups for Freescale Layerscape SoCs
- A cleanup for renesas drivers regarding MMIO accesses.
- New SoC specific drivers for Mediatek MT8192 and MT8183 power domains
- New SoC specific drivers for Aspeed AST2600 LPC bus control
and SoC identification.
- Core Power Domain support for Qualcomm MSM8916, MSM8939, SDM660
and SDX55.
- A rework of the TI AM33xx 'genpd' power domain support to use
information from DT instead of platform data
- Support for TI AM64x SoCs
- Allow building some Amlogic drivers as modules instead of built-in
Finally, there are numerous cleanups and smaller bug fixes for
Mediatek, Tegra, Samsung, Qualcomm, TI OMAP, Amlogic, Rockchips,
Renesas, and Xilinx SoCs.
There is a trivial conflict in the cedrus driver, with two branches
adding the same CEDRUS_CAPABILITY_H265_DEC flag, and another trivial
remove/remove conflict in linux/dma-mapping.h.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----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=BjJf
-----END PGP SIGNATURE-----
Merge tag 'arm-soc-drivers-5.11' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC driver updates from Arnd Bergmann:
"There are a couple of subsystems maintained by other people that merge
their drivers through the SoC tree, those changes include:
- The SCMI firmware framework gains support for sensor notifications
and for controlling voltage domains.
- A large update for the Tegra memory controller driver, integrating
it better with the interconnect framework
- The memory controller subsystem gains support for Mediatek MT8192
- The reset controller framework gains support for sharing pulsed
resets
For Soc specific drivers in drivers/soc, the main changes are
- The Allwinner/sunxi MBUS gets a rework for the way it handles
dma_map_ops and offsets between physical and dma address spaces.
- An errata fix plus some cleanups for Freescale Layerscape SoCs
- A cleanup for renesas drivers regarding MMIO accesses.
- New SoC specific drivers for Mediatek MT8192 and MT8183 power
domains
- New SoC specific drivers for Aspeed AST2600 LPC bus control and SoC
identification.
- Core Power Domain support for Qualcomm MSM8916, MSM8939, SDM660 and
SDX55.
- A rework of the TI AM33xx 'genpd' power domain support to use
information from DT instead of platform data
- Support for TI AM64x SoCs
- Allow building some Amlogic drivers as modules instead of built-in
Finally, there are numerous cleanups and smaller bug fixes for
Mediatek, Tegra, Samsung, Qualcomm, TI OMAP, Amlogic, Rockchips,
Renesas, and Xilinx SoCs"
* tag 'arm-soc-drivers-5.11' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (222 commits)
soc: mediatek: mmsys: Specify HAS_IOMEM dependency for MTK_MMSYS
firmware: xilinx: Properly align function parameter
firmware: xilinx: Add a blank line after function declaration
firmware: xilinx: Remove additional newline
firmware: xilinx: Fix kernel-doc warnings
firmware: xlnx-zynqmp: fix compilation warning
soc: xilinx: vcu: add missing register NUM_CORE
soc: xilinx: vcu: use vcu-settings syscon registers
dt-bindings: soc: xlnx: extract xlnx, vcu-settings to separate binding
soc: xilinx: vcu: drop useless success message
clk: samsung: mark PM functions as __maybe_unused
soc: samsung: exynos-chipid: initialize later - with arch_initcall
soc: samsung: exynos-chipid: order list of SoCs by name
memory: jz4780_nemc: Fix potential NULL dereference in jz4780_nemc_probe()
memory: ti-emif-sram: only build for ARMv7
memory: tegra30: Support interconnect framework
memory: tegra20: Support hardware versioning and clean up OPP table initialization
dt-bindings: memory: tegra20-emc: Document opp-supported-hw property
soc: rockchip: io-domain: Fix error return code in rockchip_iodomain_probe()
reset-controller: ti: force the write operation when assert or deassert
...
Reads the IPI buffer offset from the FW binary. The information resides
in addr of .ipi_buffer section.
Moves scp_ipi_init() to rproc_ops::parse_fw() phase. The IPI buffer can
be initialized only if the offset is clear.
To backward compatible to MT8183 SCP, specify the offset in the board
specific mtk_scp_of_data. Reads the default offset if the firmware
doesn't have it.
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Tzung-Bi Shih <tzungbi@google.com>
Link: https://lore.kernel.org/r/20201202044609.2501913-1-tzungbi@google.com
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
platform_get_resource() may fail and in this case a NULL dereference
will occur.
Fix it to use devm_platform_ioremap_resource() instead of calling
platform_get_resource() and devm_ioremap().
This is detected by Coccinelle semantic patch.
@@
expression pdev, res, n, t, e, e1, e2;
@@
res = \(platform_get_resource\|platform_get_resource_byname\)(pdev, t,
n);
+ if (!res)
+ return -EINVAL;
... when != res == NULL
e = devm_ioremap(e1, res->start, e2);
Fixes: dc160e4491 ("remoteproc: qcom: Introduce Non-PAS ADSP PIL driver")
Signed-off-by: Zhang Changzhong <zhangchangzhong@huawei.com>
Link: https://lore.kernel.org/r/1607392460-20516-1-git-send-email-zhangchangzhong@huawei.com
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
In case of error, the function devm_ioremap_wc() returns NULL pointer
not ERR_PTR(). The IS_ERR() test in the return value check should be
replaced with NULL test.
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Fixes: 6edbe024ba ("remoteproc: k3-dsp: Add a remoteproc driver of K3 C66x DSPs")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Suman Anna <s-anna@ti.com>
Link: https://lore.kernel.org/r/20200905122503.17352-1-yuehaibing@huawei.com
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
If the pm_runtime_get_sync failed in adsp_pds_enable when
loop (i), The unroll_pd_votes will start from (i - 1), and
it will resulted in following problems:
1) pm_runtime_get_sync will increment pm usage counter even it
failed. Forgetting to pm_runtime_put_noidle will result in
reference leak.
2) Have not reset pds[i] performance state.
Then we fix it.
Fixes: 17ee2fb4e8 ("remoteproc: qcom: pas: Vote for active/proxy power domains")
Signed-off-by: Zhang Qilong <zhangqilong3@huawei.com>
Link: https://lore.kernel.org/r/20201102143554.144707-1-zhangqilong3@huawei.com
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
pm_runtime_get_sync will increment pm usage counter even it
failed. Forgetting to pm_runtime_put_noidle will result in
reference leak in adsp_start, so we should fix it.
Fixes: dc160e4491 ("remoteproc: qcom: Introduce Non-PAS ADSP PIL driver")
Signed-off-by: Zhang Qilong <zhangqilong3@huawei.com>
Link: https://lore.kernel.org/r/20201102143534.144484-1-zhangqilong3@huawei.com
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
If the pm_runtime_get_sync failed in q6v5_pds_enable when
loop (i), The unroll_pd_votes will start from (i - 1), and
it will resulted in following problems:
1) pm_runtime_get_sync will increment pm usage counter even it
failed. Forgetting to pm_runtime_put_noidle will result in
reference leak.
2) Have not reset pds[i] performance state.
Then we fix it.
Fixes: 4760a896be ("remoteproc: q6v5-mss: Vote for rpmh power domains")
Signed-off-by: Zhang Qilong <zhangqilong3@huawei.com>
Link: https://lore.kernel.org/r/20201102143433.143996-1-zhangqilong3@huawei.com
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Now that this driver can be compiled with COMPILE_TEST, we have no
guarantee that CONFIG_OF will also be defined. When that happens, a
warning about mtk_scp_of_match being defined but unused will be reported
so make sure this variable is only defined if of_match_ptr() actually
uses it.
Fixes: cbd2dca749 remoteproc: scp: add COMPILE_TEST dependency
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Alexandre Courbot <acourbot@chromium.org>
Link: https://lore.kernel.org/r/20201102074007.299222-1-acourbot@chromium.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Add minidump id for modem in sm8150 chipset so that the regions to be
included in the coredump generated upon a crash is based on the minidump
tables in SMEM instead of those in the ELF header.
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Acked-by, Reviewed-by or Tested-by that you received previously.:
Signed-off-by: Siddharth Gupta <sidgup@codeaurora.org>
Link: https://lore.kernel.org/r/1605819935-10726-5-git-send-email-sidgup@codeaurora.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
This patch adds support for collecting minidump in the event of remoteproc
crash. Parse the minidump table based on remoteproc's unique minidump-id,
read all memory regions from the remoteproc's minidump table entry and
expose the memory to userspace. The remoteproc platform driver can choose
to collect a full/mini dump by specifying the coredump op.
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Co-developed-by: Rishabh Bhatnagar <rishabhb@codeaurora.org>
Signed-off-by: Rishabh Bhatnagar <rishabhb@codeaurora.org>
Co-developed-by: Gurbir Arora <gurbaror@codeaurora.org>
Signed-off-by: Gurbir Arora <gurbaror@codeaurora.org>
Signed-off-by: Siddharth Gupta <sidgup@codeaurora.org>
Link: https://lore.kernel.org/r/1605819935-10726-4-git-send-email-sidgup@codeaurora.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
This change adds a new kind of core dump mechanism which instead of dumping
entire program segments of the firmware, dumps sections of the remoteproc
memory which are sufficient to allow debugging the firmware. This function
thus uses section headers instead of program headers during creation of the
core dump elf.
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Co-developed-by: Rishabh Bhatnagar <rishabhb@codeaurora.org>
Signed-off-by: Rishabh Bhatnagar <rishabhb@codeaurora.org>
Signed-off-by: Siddharth Gupta <sidgup@codeaurora.org>
Link: https://lore.kernel.org/r/1605819935-10726-3-git-send-email-sidgup@codeaurora.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Each remoteproc might have different requirements for coredumps and might
want to choose the type of dumps it wants to collect. This change allows
remoteproc drivers to specify their own custom dump function to be executed
in place of rproc_coredump. If the coredump op is not specified by the
remoteproc driver it will be set to rproc_coredump by default.
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Siddharth Gupta <sidgup@codeaurora.org>
Link: https://lore.kernel.org/r/1605819935-10726-2-git-send-email-sidgup@codeaurora.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The K3 J721E family of SoCs have a revised version of the AM65x ICSSG IP
and contains two instances of this newer ICSSG IP. Each ICSSG processor
subsystem contains 2 primary PRU cores, 2 auxiliary PRU cores called RTUs,
and 2 new auxiliary cores called Transmit PRUs (Tx_PRUs).
Enhance the existing PRU remoteproc driver to support these new PRU
and RTU cores by using specific compatibles. The cores have the same
memory copying limitations as on AM65x, so reuses the custom memcpy
function within the driver's ELF loader implementation. The initial
names for the firmware images for each PRU core are retrieved from
DT nodes, and can be adjusted through sysfs if required.
Signed-off-by: Suman Anna <s-anna@ti.com>
Co-developed-by: Grzegorz Jaszczyk <grzegorz.jaszczyk@linaro.org>
Signed-off-by: Grzegorz Jaszczyk <grzegorz.jaszczyk@linaro.org>
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Link: https://lore.kernel.org/r/20201208141002.17777-7-grzegorz.jaszczyk@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The K3 AM65x family of SoCs have the next generation of the PRU-ICSS
processor subsystem, commonly referred to as ICSSG. Each ICSSG processor
subsystem on AM65x SR1.0 contains two primary PRU cores and two new
auxiliary PRU cores called RTUs. The AM65x SR2.0 SoCs have a revised
ICSSG IP that is based off the subsequent IP revision used on J721E
SoCs. This IP instance has two new custom auxiliary PRU cores called
Transmit PRUs (Tx_PRUs) in addition to the existing PRUs and RTUs.
Each RTU and Tx_PRU cores have their own dedicated IRAM (smaller than
a PRU), Control and debug feature sets, but is different in terms of
sub-modules integrated around it and does not have the full capabilities
associated with a PRU core. The RTU core is typically used to aid a
PRU core in accelerating data transfers, while the Tx_PRU cores is
normally used to control the TX L2 FIFO if enabled in Ethernet
applications. Both can also be used to run independent applications.
The RTU and Tx_PRU cores though share the same Data RAMs as the PRU
cores, so the memories have to be partitioned carefully between different
applications. The new cores also support a new sub-module called Task
Manager to support two different context thread executions.
Enhance the existing PRU remoteproc driver to support these new PRU, RTU
and Tx PRU cores by using specific compatibles. The initial names for the
firmware images for each PRU core are retrieved from DT nodes, and can
be adjusted through sysfs if required.
The PRU remoteproc driver has to be specifically modified to use a
custom memcpy function within its ELF loader implementation for these
new cores in order to overcome a limitation with copying data into each
of the core's IRAM memories. These memory ports support only 4-byte
writes, and any sub-word order byte writes clear out the remaining
bytes other than the bytes being written within the containing word.
The default ARM64 memcpy also cannot be used as it throws an exception
when the preferred 8-byte copy operation is attempted. This choice is
made by using a state flag that is set only on K3 SoCs.
Signed-off-by: Suman Anna <s-anna@ti.com>
Co-developed-by: Grzegorz Jaszczyk <grzegorz.jaszczyk@linaro.org>
Signed-off-by: Grzegorz Jaszczyk <grzegorz.jaszczyk@linaro.org>
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Link: https://lore.kernel.org/r/20201208141002.17777-6-grzegorz.jaszczyk@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The remoteproc core creates certain standard debugfs entries,
that does not give a whole lot of useful information for the
PRUs. The PRU remoteproc driver is enhanced to add additional
debugfs entries for PRU. These will be auto-cleaned up when
the parent rproc debug directory is removed.
The enhanced debugfs support adds two new entries: 'regs' and
'single_step'. The 'regs' dumps out the useful CTRL sub-module
registers as well as each of the 32 GPREGs and CT_REGs registers.
The GPREGs and CT_REGs though are printed only when the PRU is
halted and accessible as per the IP design.
The 'single_step' utilizes the single-step execution of the PRU
cores. Writing a non-zero value performs a single step, and a
zero value restores the PRU to execute in the same mode as the
mode before the first single step. (note: if the PRU is halted
because of a halt instruction, then no change occurs).
Logic for setting the PC and jumping over a halt instruction shall
be added in the future.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Grzegorz Jaszczyk <grzegorz.jaszczyk@linaro.org>
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Link: https://lore.kernel.org/r/20201208141002.17777-5-grzegorz.jaszczyk@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The firmware blob can contain optional ELF sections: .resource_table
section and .pru_irq_map one. The second one contains the PRUSS
interrupt mapping description, which needs to be setup before powering
on the PRU core. To avoid RAM wastage this ELF section is not mapped to
any ELF segment (by the firmware linker) and therefore is not loaded to
PRU memory.
The PRU interrupt configuration is handled within the PRUSS INTC irqchip
driver and leverages the system events to interrupt channels and host
interrupts mapping configuration. Relevant irq routing information is
passed through a special .pru_irq_map ELF section (for interrupts routed
to and used by PRU cores) or via the PRU application's device tree node
(for interrupts routed to and used by the main CPU). The mappings are
currently programmed during the booting/shutdown of the PRU.
The interrupt configuration passed through .pru_irq_map ELF section is
optional. It varies on specific firmware functionality and therefore
have to be unwinded during PRU stop and performed again during
PRU start.
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Co-developed-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Grzegorz Jaszczyk <grzegorz.jaszczyk@linaro.org>
Link: https://lore.kernel.org/r/20201208141002.17777-4-grzegorz.jaszczyk@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The Programmable Real-Time Unit Subsystem (PRUSS) consists of
dual 32-bit RISC cores (Programmable Real-Time Units, or PRUs)
for program execution. This patch adds a remoteproc platform
driver for managing the individual PRU RISC cores life cycle.
The PRUs do not have a unified address space (have an Instruction
RAM and a primary Data RAM at both 0x0). The PRU remoteproc driver
therefore uses a custom remoteproc core ELF loader ops. The added
.da_to_va ops is only used to provide translations for the PRU
Data RAMs. This remoteproc driver does not have support for error
recovery and system suspend/resume features. Different compatibles
are used to allow providing scalability for instance-specific device
data if needed. The driver uses a default firmware-name retrieved
from device-tree for each PRU core, and the firmwares are expected
to be present in the standard Linux firmware search paths. They can
also be adjusted by userspace if required through the sysfs interface
provided by the remoteproc core.
The PRU remoteproc driver uses a client-driven boot methodology: it
does _not_ support auto-boot so that the PRU load and boot is dictated
by the corresponding client drivers for achieving various usecases.
This allows flexibility for the client drivers or applications to set
a firmware name (if needed) based on their desired functionality and
boot the PRU. The sysfs bind and unbind attributes have also been
suppressed so that the PRU devices cannot be unbound and thereby
shutdown a PRU from underneath a PRU client driver.
The driver currently supports the AM335x, AM437x, AM57xx and 66AK2G
SoCs, and support for other TI SoCs will be added in subsequent
patches.
Co-developed-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Suman Anna <s-anna@ti.com>
Co-developed-by: Grzegorz Jaszczyk <grzegorz.jaszczyk@linaro.org>
Signed-off-by: Grzegorz Jaszczyk <grzegorz.jaszczyk@linaro.org>
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Link: https://lore.kernel.org/r/20201208141002.17777-3-grzegorz.jaszczyk@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The latest version of sysmon_stop() starts by initializing
the sysmon->shutdown_acked variable, but then overwrites it
with an uninitialized variable later:
drivers/remoteproc/qcom_sysmon.c:551:11: error: variable 'acked' is used uninitialized whenever 'if' condition is false [-Werror,-Wsometimes-uninitialized]
else if (sysmon->ept)
^~~~~~~~~~~
drivers/remoteproc/qcom_sysmon.c:554:27: note: uninitialized use occurs here
sysmon->shutdown_acked = acked;
^~~~~
Remove the local 'acked' variable again and set the state directly.
Fixes: 5c212aaf54 ("remoteproc: sysmon: Expose the shutdown result")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20201204193740.3162065-1-arnd@kernel.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The J7200 SoCs have a revised R5FSS IP that adds a unique feature w.r.t
TCM sizing. Each R5F core in a cluster typically has 32 KB each of ATCM
and BTCM, with only the Core0 TCMs usable in LockStep mode. This revised
IP however doubles the total available TCM in LockStep mode by making the
Core1 TCM visible immediately after the corresponding Core0 TCM.
The R5F DT nodes on the J7200 SoCs define double (64 KB) the normal TCM
size (32 KB) for R5F Core0 for each of ATCM and BTCM to represent the
above. This increased TCM memory is only usable in LockStep-mode, and
has to be adjusted to the normal 32 KB size in Split mode. Enhance the
TI K3 R5F remoteproc for this logic through a new function. The adjustment
is a no-op on prior SoCs and relies on the correct DTS node sizes in
LockStep-mode on applicable SoCs.
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Suman Anna <s-anna@ti.com>
Link: https://lore.kernel.org/r/20201119010531.21083-4-s-anna@ti.com
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The K3 J7200 SoC family has a revised R5F sub-system and contains a
subset of the R5F clusters present on J721E SoCs. The K3 J7200 SoCs
only have two dual-core Arm R5F clusters/subsystems with 2 R5F cores
each. One cluster is present within the MCU voltage domain (MCU_R5FSS0),
while the other is present in the MAIN voltage domain (MAIN_R5FSS0).
The revised IP has the following two new features:
1. TCMs are auto-initialized during module power-up, and the behavior
is programmable through a MMR bit.
2. The LockStep-mode allows the Core1 TCMs to be combined with the
Core0 TCMs effectively doubling the amount of TCMs available.
The LockStep-mode on previous SoCs could only use the Core0 TCMs.
This combined TCMs appear contiguous at the respective Core0 TCM
addresses.
Extend the support to these clusters in the K3 R5F remoteproc driver
using J7200 specific compatibles. Logic for the second feature is
added in the next patch. The integration of these clusters is very
much similar to J721E SoCs otherwise.
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Suman Anna <s-anna@ti.com>
Link: https://lore.kernel.org/r/20201119010531.21083-3-s-anna@ti.com
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
A new API, rproc_set_firmware() is added to allow the remoteproc platform
drivers and remoteproc client drivers to be able to configure a custom
firmware name that is different from the default name used during
remoteproc registration. This function is being introduced to provide
a kernel-level equivalent of the current sysfs interface to remoteproc
client drivers, and can only change firmwares when the remoteproc is
offline. This allows some remoteproc drivers to choose different firmwares
at runtime based on the functionality the remote processor is providing.
The TI PRU Ethernet driver will be an example of such usage as it
requires to use different firmwares for different supported protocols.
Also, update the firmware_store() function used by the sysfs interface
to reuse this function to avoid code duplication.
Reviewed-by: Rishabh Bhatnagar <rishabhb@codeaurora.org>
Signed-off-by: Suman Anna <s-anna@ti.com>
Link: https://lore.kernel.org/r/20201121032042.6195-1-s-anna@ti.com
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Improve the style of a few of the error messages printed by the sysmon
implementation and fix the copy-pasted shutdown error in the send-event
function.
Tested-by: Steev Klimaszewski <steev@kali.org>
Reviewed-by: Rishabh Bhatnagar <rishabhb@codeaurora.org>
Link: https://lore.kernel.org/r/20201122054135.802935-5-bjorn.andersson@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Requesting a graceful shutdown through the shared memory state signals
will not be acked in the event that sysmon has already successfully shut
down the remote firmware. So extend the stop request API to optionally
take the remoteproc's sysmon instance and query if there's already been
a successful shutdown attempt, before doing the signal dance.
Tested-by: Steev Klimaszewski <steev@kali.org>
Reviewed-by: Rishabh Bhatnagar <rishabhb@codeaurora.org>
Link: https://lore.kernel.org/r/20201122054135.802935-4-bjorn.andersson@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
A graceful shutdown of the Qualcomm remote processors where
traditionally performed by invoking a shared memory state signal and
waiting for the associated ack.
This was later superseded by the "sysmon" mechanism, where some form of
shared memory bus is used to send a "graceful shutdown request" message
and one of more signals comes back to indicate its success.
But when this newer mechanism is in effect the firmware is shut down by
the time the older mechanism, implemented in the remoteproc drivers,
attempts to perform a graceful shutdown - and as such it will never
receive an ack back.
This patch therefor track the success of the latest shutdown attempt in
sysmon and exposes a new function in the API that the remoteproc driver
can use to query the success and the necessity of invoking the older
mechanism.
Tested-by: Steev Klimaszewski <steev@kali.org>
Reviewed-by: Rishabh Bhatnagar <rishabhb@codeaurora.org>
Link: https://lore.kernel.org/r/20201122054135.802935-3-bjorn.andersson@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The reliance on the remoteproc's state for determining when to send
sysmon notifications to a remote processor is racy with regard to
concurrent remoteproc operations.
Further more the advertisement of the state of other remote processor to
a newly started remote processor might not only send the wrong state,
but might result in a stream of state changes that are out of order.
Address this by introducing state tracking within the sysmon instances
themselves and extend the locking to ensure that the notifications are
consistent with this state.
Fixes: 1f36ab3f6e ("remoteproc: sysmon: Inform current rproc about all active rprocs")
Fixes: 1877f54f75 ("remoteproc: sysmon: Add notifications for events")
Fixes: 1fb82ee806 ("remoteproc: qcom: Introduce sysmon")
Cc: stable@vger.kernel.org
Reviewed-by: Rishabh Bhatnagar <rishabhb@codeaurora.org>
Link: https://lore.kernel.org/r/20201122054135.802935-2-bjorn.andersson@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The application processor accessing the MBA region after assigning it to
the remote Q6 would lead to an XPU violation. Fix this by un-mapping the
MBA region post firmware copy and MBA text log dumps.
Signed-off-by: Sibi Sankar <sibis@codeaurora.org>
Link: https://lore.kernel.org/r/1604473422-29639-2-git-send-email-sibis@codeaurora.org
[bjorn: Renamed "ptr" to "mba_region"]
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Fix the sparse warnings reported by the kernel test bot by replacing
ioremap calls with memremap.
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Sibi Sankar <sibis@codeaurora.org>
Link: https://lore.kernel.org/r/1604473422-29639-1-git-send-email-sibis@codeaurora.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The only usage of qmi_indication_handler[] is to pass its address to
qmi_handle_init() which accepts a const pointer. Make it const to allow
the compiler to put it in read-only memory.
Signed-off-by: Rikard Falkeborn <rikard.falkeborn@gmail.com>
Link: https://lore.kernel.org/r/20201122234540.34623-1-rikard.falkeborn@gmail.com
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The main purpose of the loop is to load the memory to the SCP SRAM.
If filesz is 0, can go to next program header directly.
We don't need to try to validate the FW binary for those filesz==0
segments.
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Tzung-Bi Shih <tzungbi@google.com>
Link: https://lore.kernel.org/r/20201116084413.3312631-3-tzungbi@google.com
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
It is valid if offset+length == sram_size.
For example, sram_size=100, offset=99, length=1. Accessing offset 99
with length 1 is valid.
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Tzung-Bi Shih <tzungbi@google.com>
Link: https://lore.kernel.org/r/20201116084413.3312631-2-tzungbi@google.com
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Fixes the following sparse errors on dma_alloc_coherent() and
dma_free_coherent().
On drivers/remoteproc/mtk_scp.c:559:23:
warning: incorrect type in assignment (different address spaces)
expected void [noderef] __iomem *cpu_addr
got void *
On drivers/remoteproc/mtk_scp.c:572:56:
warning: incorrect type in argument 3 (different address spaces)
expected void *cpu_addr
got void [noderef] __iomem *cpu_addr
The cpu_addr is not a __iomem address. Removes the marker.
Reviewed-by: Nicolas Boichat <drinkcat@chromium.org>
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Tzung-Bi Shih <tzungbi@google.com>
Link: https://lore.kernel.org/r/20201116082537.3287009-3-tzungbi@google.com
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The only usage of st_rproc_ops is to pass its address to rproc_alloc()
which accepts a const pointer. Make it const to allow the compiler to
put it in read-only memory.
Acked-by: Arnaud Pouliquen <arnaud.pouliquen@st.com>
Signed-off-by: Rikard Falkeborn <rikard.falkeborn@gmail.com>
Link: https://lore.kernel.org/r/20201107233630.9728-3-rikard.falkeborn@gmail.com
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The only usage of ingenic_rproc_ops is to pass its address to
devm_rproc_alloc(), which accepts a const pointer. Make it const to
allow the compiler to put it in read-only memory.
Acked-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Rikard Falkeborn <rikard.falkeborn@gmail.com>
Link: https://lore.kernel.org/r/20201107233630.9728-2-rikard.falkeborn@gmail.com
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
In order to move wkup_m3 to probe without platform data, let's add
support for using optional reset control driver if configured in the
dts. With this change and the related dts change, we can start
dropping the platform data for am335x.
And once wkup_m3 no longer needs platform data, we can simply drop the
related legacy reset platform data callbacks from wkup_m3 driver later
on after also am437x no longer depends on it.
Cc: linux-remoteproc@vger.kernel.org
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Dave Gerlach <d-gerlach@ti.com>
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Cc: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The function cast causes a warning with "make W=1"
drivers/remoteproc/ti_k3_r5_remoteproc.c: In function 'k3_r5_probe':
drivers/remoteproc/ti_k3_r5_remoteproc.c:1368:12: warning: cast between incompatible function types from 'int (*)(struct platform_device *)' to 'void (*)(void *)' [-Wcast-function-type]
Rewrite the code to avoid the cast, and fix the incorrect return
type of the callback.
Fixes: 6dedbd1d54 ("remoteproc: k3-r5: Add a remoteproc driver for R5F subsystem")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20201026160533.3705998-1-arnd@kernel.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
So far we have been doing all proxy votes by voting for raw voltages/load
through the regulator interface. But actually VDDCX and VDDMX represent
power domains that should be preferably managed using corner votes
through the power domain interface.
Looking closer the code was actually never doing the proxy votes
correctly: The vddcx regulator is specified as:
{ "vddcx", .super_turbo = true },
which is supposed to say that we should vote for the maximum corner
of the VDDCX power domain. But actually "super_turbo" is unused so
all we did so far is to enable the power domain. We did not vote for
it to scale to the maximum performance state.
Using them through the power domain interface allows voting for the
maximum performance state. However, we still need to support using
them through the regulator interface for old device trees.
The way this is implemented here is that we check if attaching the
two power domain succeeds. If yes, we skip the first "num_pd_vregs"
regulators in the "vregs" list and only request the remaining ones.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20200916104135.25085-9-stephan@gerhold.net
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Newer platforms vote for necessary power domains through the power
domain subsystem. For historical reasons older platforms like MSM8916
or MSM8974 still control these as regulators.
Managing them as power domains is preferred since that allows us
to vote for corners instead of raw voltages.
Make it possible for MSM8916 and MSM8974 to manage these as power
domains. For compatibility with old device trees we still need to
support falling back to the regulators when necessary.
The way this is implemented here is that the deprecated regulators
are defined as "fallback_proxy_supply". Only if attaching the power
domains fails because they are not specified (-ENODATA) we request
and manage the fallback regulators instead.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20200916104135.25085-7-stephan@gerhold.net
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
This introduces support for the Mediatek MT9182 SCP and controlling the
Cortex R5F processors found in TI K3 platforms. It clones the
longstanding debugfs interface for controlling crash handling to sysfs.
Lastly it solves a bug where after a warm reset of Qualcomm platforms
the modem would crash upon first boot.
-----BEGIN PGP SIGNATURE-----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=FhqD
-----END PGP SIGNATURE-----
Merge tag 'rproc-v5.10' of git://git.kernel.org/pub/scm/linux/kernel/git/andersson/remoteproc
Pull remoteproc updates from Bjorn Andersson:
"This introduces support for the Mediatek MT9182 SCP and controlling
the Cortex R5F processors found in TI K3 platforms. It clones the
longstanding debugfs interface for controlling crash handling to
sysfs. Lastly it solves a bug where after a warm reset of Qualcomm
platforms the modem would crash upon first boot"
* tag 'rproc-v5.10' of git://git.kernel.org/pub/scm/linux/kernel/git/andersson/remoteproc:
remoteproc/mediatek: Remove non-standard dsb()
remoteproc: Add recovery configuration to the sysfs interface
remoteproc: Add coredump as part of sysfs interface
remoteproc: Change default dump configuration to "disabled"
remoteproc: k3-r5: Add loading support for on-chip SRAM regions
remoteproc: k3-r5: Initialize TCM memories for ECC
remoteproc: k3-r5: Add a remoteproc driver for R5F subsystem
dt-bindings: remoteproc: Add bindings for R5F subsystem on TI K3 SoCs
remoteproc/mediatek: Add support for mt8192 SCP
remoteproc: Fixup coredump debugfs disable request
remoteproc: qcom_q6v5: Assign mpss region to Q6 before MBA boot
remoteproc/mediatek: fix null pointer dereference on null scp pointer
remoteproc: stm32: Fix pointer assignement
remoteproc: scp: add COMPILE_TEST dependency
As reported by Stephen, dsb() is not declared on e.g. x86_64, preventing
the mtp_scp from building. Simply remove the barrier (and the readback),
suggested by Pi-Hsun to resolve this.
Fixes: fd0b6c1ff8 ("remoteproc/mediatek: Add support for mt8192 SCP")
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Suggested-by: Pi-Hsun Shih <pihsun@chromium.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
- rework the non-coherent DMA allocator
- move private definitions out of <linux/dma-mapping.h>
- lower CMA_ALIGNMENT (Paul Cercueil)
- remove the omap1 dma address translation in favor of the common
code
- make dma-direct aware of multiple dma offset ranges (Jim Quinlan)
- support per-node DMA CMA areas (Barry Song)
- increase the default seg boundary limit (Nicolin Chen)
- misc fixes (Robin Murphy, Thomas Tai, Xu Wang)
- various cleanups
-----BEGIN PGP SIGNATURE-----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=Bkf/
-----END PGP SIGNATURE-----
Merge tag 'dma-mapping-5.10' of git://git.infradead.org/users/hch/dma-mapping
Pull dma-mapping updates from Christoph Hellwig:
- rework the non-coherent DMA allocator
- move private definitions out of <linux/dma-mapping.h>
- lower CMA_ALIGNMENT (Paul Cercueil)
- remove the omap1 dma address translation in favor of the common code
- make dma-direct aware of multiple dma offset ranges (Jim Quinlan)
- support per-node DMA CMA areas (Barry Song)
- increase the default seg boundary limit (Nicolin Chen)
- misc fixes (Robin Murphy, Thomas Tai, Xu Wang)
- various cleanups
* tag 'dma-mapping-5.10' of git://git.infradead.org/users/hch/dma-mapping: (63 commits)
ARM/ixp4xx: add a missing include of dma-map-ops.h
dma-direct: simplify the DMA_ATTR_NO_KERNEL_MAPPING handling
dma-direct: factor out a dma_direct_alloc_from_pool helper
dma-direct check for highmem pages in dma_direct_alloc_pages
dma-mapping: merge <linux/dma-noncoherent.h> into <linux/dma-map-ops.h>
dma-mapping: move large parts of <linux/dma-direct.h> to kernel/dma
dma-mapping: move dma-debug.h to kernel/dma/
dma-mapping: remove <asm/dma-contiguous.h>
dma-mapping: merge <linux/dma-contiguous.h> into <linux/dma-map-ops.h>
dma-contiguous: remove dma_contiguous_set_default
dma-contiguous: remove dev_set_cma_area
dma-contiguous: remove dma_declare_contiguous
dma-mapping: split <linux/dma-mapping.h>
cma: decrease CMA_ALIGNMENT lower limit to 2
firewire-ohci: use dma_alloc_pages
dma-iommu: implement ->alloc_noncoherent
dma-mapping: add new {alloc,free}_noncoherent dma_map_ops methods
dma-mapping: add a new dma_alloc_pages API
dma-mapping: remove dma_cache_sync
53c700: convert to dma_alloc_noncoherent
...
Add recovery configuration to the sysfs interface. This will
allow usage of this configuration feature in production
devices where access to debugfs might be limited.
Signed-off-by: Rishabh Bhatnagar <rishabhb@codeaurora.org>
Link: https://lore.kernel.org/r/1601662144-5964-4-git-send-email-rishabhb@codeaurora.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Add coredump as part of the sysfs interface. This will
allow usage of this configuration feature in production
devices where access to debugfs might be limited.
Signed-off-by: Rishabh Bhatnagar <rishabhb@codeaurora.org>
Link: https://lore.kernel.org/r/1601662144-5964-3-git-send-email-rishabhb@codeaurora.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Currently "default" configuration option means coredumps are
enabled. To avoid confusion rename the "default" configuration
option to "enabled" and disable collection of dumps by default
as doing so makes sense for production devices.
Signed-off-by: Rishabh Bhatnagar <rishabhb@codeaurora.org>
Link: https://lore.kernel.org/r/1601662144-5964-2-git-send-email-rishabhb@codeaurora.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The K3 SoCs has various internal on-chip SRAM memories like the SRAM
within the MCU domain or the shared MSMC RAM within NavSS that can be
used for multiple purposes. One such purpose is to have the R5F cores
use a portion of such on-chip SRAM for fast-access data or to directly
execute code.
Add support to the K3 R5 remoteproc driver to parse and support
loading into such memories. The SRAM regions need to be mapped as
normal non-cacheable memory to avoid kernel crashes when the remoteproc
loader code uses the Arm64 memset library function (the "DC ZVA"
instruction throws a alignment fault on device type memory).
These SRAM regions are completely optional as not all firmware images
require these memories, and any such memory has to be reserved as such
in the DTS files.
Signed-off-by: Suman Anna <s-anna@ti.com>
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Link: https://lore.kernel.org/r/20201002234234.20704-5-s-anna@ti.com
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The R5F processors on K3 SoCs all have two TCMs (ATCM and BTCM) that
support 32-bit ECC. The TCMs are typically loaded with some boot-up
code to initialize the R5 MPUs to further execute code out of DDR.
The ECC for the TCMs is enabled by default on K3 SoCs due to internal
default tie-off values, but the TCM memories are not initialized on
device power up. Any read access without the corresponding TCM memory
location initialized will generate an ECC error, and any such access
from a A72 or A53 core will trigger a SError.
So, zero initialize both the TCM memories before loading any firmware
onto a R5F in remoteproc mode. Any R5F booted from U-Boot/SPL would
require a similar initialization in the bootloader. Note that both
the TCMs are initialized unconditionally as the TCM enable config bits
only manage the access and visibility from R5.
Signed-off-by: Suman Anna <s-anna@ti.com>
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Link: https://lore.kernel.org/r/20201002234234.20704-4-s-anna@ti.com
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The TI K3 family of SoCs typically have one or more dual-core Arm Cortex
R5F processor clusters/subsystems (R5FSS). This R5F subsystem/cluster
can be configured at boot time to be either run in a LockStep mode or in
an Asymmetric Multi Processing (AMP) fashion in Split-mode. This subsystem
has 64 KB each Tightly-Coupled Memory (TCM) internal memories for each
core split between two banks - TCMA and TCMB (further interleaved into
two banks). The subsystem does not have an MMU, but has a Region Address
Translater (RAT) module that is accessible only from the R5Fs for providing
translations between 32-bit CPU addresses into larger system bus addresses.
Add a remoteproc driver to support this subsystem to be able to load and
boot the R5F cores primarily in LockStep mode. The code also includes the
base support for Split mode. Error Recovery and Power Management features
are not currently supported. Loading support includes the internal TCMs
and DDR. RAT support is left for a future patch, and as such the reserved
memory carveout regions are all expected to be using memory regions within
the first 2 GB.
The R5F remote processors do not have an MMU, and so require fixed memory
carveout regions matching the firmware image addresses. Support for this
is provided by mandating multiple memory regions to be attached to the
remoteproc device. The first memory region will be used to serve as the
DMA pool for all dynamic allocations like the vrings and vring buffers.
The remaining memory regions are mapped into the kernel at device probe
time, and are used to provide address translations for firmware image
segments without the need for any RSC_CARVEOUT entries. Any firmware
image using memory outside of the supplied reserved memory carveout
regions will be errored out.
The R5F processors on TI K3 SoCs require a specific sequence for booting
and shutting down the processors. This sequence is also dependent on the
mode (LockStep or Split) the R5F cluster is configured for. The R5F cores
have a Memory Protection Unit (MPU) that has a default configuration that
does not allow the cores to run out of DDR out of reset. This is resolved
by using the TCMs for boot-strapping code that applies the appropriate
executable permissions on desired DDR memory. The loading into the TCMs
requires that the resets be released first with the cores in halted state.
The Power Sleep Controller (PSC) module on K3 SoCs requires that the cores
be in WFI/WFE states with no active bus transactions before the cores can
be put back into reset. Support for this is provided by using the newly
introduced .prepare() and .unprepare() ops in the remoteproc core. The
.prepare() ops is invoked before any loading, and the .unprepare() ops
is invoked after the remoteproc resource cleanup. The R5F core resets
are deasserted in .prepare() and asserted in .unprepare(), and the cores
themselves are started and halted in .start() and .stop() ops. This
ensures symmetric usage and allows the R5F cores state machine to be
maintained properly between using the sysfs 'state' variable, bind/unbind
and regular module load/unload flows.
The subsystem is represented as a single remoteproc in LockStep mode, and
as two remoteprocs in Split mode. The driver uses various TI-SCI interfaces
to talk to the System Controller (DMSC) for managing configuration, power
and reset management of these cores. IPC between the A53 cores and the R5
cores is supported through the virtio rpmsg stack using shared memory and
OMAP Mailboxes.
The AM65x SoCs typically have a single R5FSS in the MCU voltage domain. The
J721E SoCs uses a slightly revised IP and typically have three R5FSSs, with
one cluster present within the MCU voltage domain (MCU_R5FSS0), and the
remaining two clusters present in the MAIN voltage domain (MAIN_R5FSS0 and
MAIN_R5FSS1). The integration of these clusters on J721E SoC is also
slightly different in that these IPs do support an actual local reset line,
while they are a no-op on AM65x SoCs.
Signed-off-by: Suman Anna <s-anna@ti.com>
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Link: https://lore.kernel.org/r/20201002234234.20704-3-s-anna@ti.com
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Split out all the bits that are purely for dma_map_ops implementations
and related code into a new <linux/dma-map-ops.h> header so that they
don't get pulled into all the drivers. That also means the architecture
specific <asm/dma-mapping.h> is not pulled in by <linux/dma-mapping.h>
any more, which leads to a missing includes that were pulled in by the
x86 or arm versions in a few not overly portable drivers.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Fix the discrepancy observed between accepted input and read back value
while disabling remoteproc coredump through the coredump debugfs entry.
Fixes: 3afdc59e43 ("remoteproc: Add coredump debugfs entry")
Cc: stable@vger.kernel.org
Signed-off-by: Sibi Sankar <sibis@codeaurora.org>
Link: https://lore.kernel.org/r/20200916145100.15872-1-sibis@codeaurora.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
On secure devices which support warm reset, the MBA firmware requires
access to the modem region to clear them out. Hence provide Q6 access
to this region before MBA boot. This will be a nop during a modem SSR.
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Sibi Sankar <sibis@codeaurora.org>
Link: https://lore.kernel.org/r/20200917175840.18708-1-sibis@codeaurora.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Currently when pointer scp is null a dev_err is being called that
references the pointer which is the very thing we are trying to
avoid doing. Remove the extraneous error message to avoid this
issue.
Addresses-Coverity: ("Dereference after null check")
Fixes: 63c13d61ea ("remoteproc/mediatek: add SCP support for mt8183")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Link: https://lore.kernel.org/r/20200918152428.27258-1-colin.king@canonical.com
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The new field 'dma_range_map' in struct device is used to facilitate the
use of single or multiple offsets between mapping regions of cpu addrs and
dma addrs. It subsumes the role of "dev->dma_pfn_offset" which was only
capable of holding a single uniform offset and had no region bounds
checking.
The function of_dma_get_range() has been modified so that it takes a single
argument -- the device node -- and returns a map, NULL, or an error code.
The map is an array that holds the information regarding the DMA regions.
Each range entry contains the address offset, the cpu_start address, the
dma_start address, and the size of the region.
of_dma_configure() is the typical manner to set range offsets but there are
a number of ad hoc assignments to "dev->dma_pfn_offset" in the kernel
driver code. These cases now invoke the function
dma_direct_set_offset(dev, cpu_addr, dma_addr, size).
Signed-off-by: Jim Quinlan <james.quinlan@broadcom.com>
[hch: various interface cleanups]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Tested-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Tested-by: Nathan Chancellor <natechancellor@gmail.com>
Fix the assignment of the @state pointer - it is obviously wrong.
Acked-by: Arnaud Pouliquen <arnaud.pouliquen@st.com>
Fixes: 376ffdc044 ("remoteproc: stm32: Properly set co-processor state when attaching")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Link: https://lore.kernel.org/r/20200831213758.206690-1-mathieu.poirier@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
This introduces a new "detached" state for remote processors that are
deemed to be running at the time Linux boots and the infrastructure for
"attaching" to these. It then introduces the support for performing this
operation for the STM32 platform.
The coredump functionality is moved out from the core file and gains
support for an optional mode where the recovery phase awaits the
notification from devcoredump that the dump should be released. This
allows userspace to grab the coredump in scenarios where vmalloc space
is too low for creating a complete copy of the coredump before handing
this to devcoredump.
A new character device based interface is introduced to allow tying the
stoppage of a remote processor to the termination of a user space
process. This is useful in situations when such process provides crucial
resources/operations for the firmware running on the remote processor.
The Texas Instrument K3 driver gains support for the C66x and C71x DSPs.
Qualcomm remoteprocs gains support for stashing relocation information
in IMEM, to aid post mortem debugging and the crash notification
mechanism is generalized to be reusable in cases where loosely coupled
drivers needs to know about the status of a remote processor. One such
example is the IPA hardware block, which is jointly owned with the
modem and migrated to this improved interface.
It also introduces a number of bug fixes and debug improvements for the
Qualcomm modem remoteproc driver.
And it cleans up the inconsistent interface for remoteproc drivers to
implement power management.
-----BEGIN PGP SIGNATURE-----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=9cjt
-----END PGP SIGNATURE-----
Merge tag 'rproc-v5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/andersson/remoteproc
Pull remoteproc updates from Bjorn Andersson:
"This introduces a new "detached" state for remote processors that are
deemed to be running at the time Linux boots and the infrastructure
for "attaching" to these. It then introduces the support for
performing this operation for the STM32 platform.
The coredump functionality is moved out from the core file and gains
support for an optional mode where the recovery phase awaits the
notification from devcoredump that the dump should be released. This
allows userspace to grab the coredump in scenarios where vmalloc space
is too low for creating a complete copy of the coredump before handing
this to devcoredump.
A new character device based interface is introduced to allow tying
the stoppage of a remote processor to the termination of a user space
process. This is useful in situations when such process provides
crucial resources/operations for the firmware running on the remote
processor.
The Texas Instrument K3 driver gains support for the C66x and C71x
DSPs.
Qualcomm remoteprocs gains support for stashing relocation information
in IMEM, to aid post mortem debugging and the crash notification
mechanism is generalized to be reusable in cases where loosely coupled
drivers needs to know about the status of a remote processor. One such
example is the IPA hardware block, which is jointly owned with the
modem and migrated to this improved interface.
It also introduces a number of bug fixes and debug improvements for
the Qualcomm modem remoteproc driver.
And it cleans up the inconsistent interface for remoteproc drivers to
implement power management"
* tag 'rproc-v5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/andersson/remoteproc: (56 commits)
remoteproc: core: Register the character device interface
remoteproc: Add remoteproc character device interface
remoteproc: kill IPA notify code
net: ipa: new notification infrastructure
remoteproc: k3-dsp: Add support for C71x DSPs
dt-bindings: remoteproc: k3-dsp: Update bindings for C71x DSPs
remoteproc: k3-dsp: Add support for L2RAM loading on C66x DSPs
remoteproc: k3-dsp: Add a remoteproc driver of K3 C66x DSPs
dt-bindings: remoteproc: Add bindings for C66x DSPs on TI K3 SoCs
remoteproc: k3: Add TI-SCI processor control helper functions
remoteproc: Introduce rproc_of_parse_firmware() helper
dt-bindings: arm: keystone: Add common TI SCI bindings
remoteproc: qcom_q6v5_mss: Remove redundant running state
remoteproc: qcom: q6v5: Update running state before requesting stop
remoteproc: qcom_q6v5_mss: Add modem debug policy support
remoteproc: qcom_q6v5_mss: Validate modem blob firmware size before load
remoteproc: qcom_q6v5_mss: Validate MBA firmware size before load
rpmsg: update documentation
remoteproc: qcom_q6v5_mss: Add MBA log extraction support
remoteproc: Add coredump debugfs entry
...
Add the character device during rproc_add. This would create
a character device node at /dev/remoteproc<index>. Userspace
applications can interact with the remote processor using this
interface.
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Rishabh Bhatnagar <rishabhb@codeaurora.org>
Signed-off-by: Siddharth Gupta <sidgup@codeaurora.org>
Link: https://lore.kernel.org/r/1596044401-22083-3-git-send-email-sidgup@codeaurora.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Add the character device interface into remoteproc framework.
This interface can be used in order to boot/shutdown remote
subsystems and provides a basic ioctl based interface to implement
supplementary functionality. An ioctl call is implemented to enable
the shutdown on release feature which will allow remote processors to
be shutdown when the controlling userspace application crashes or hangs.
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Rishabh Bhatnagar <rishabhb@codeaurora.org>
Signed-off-by: Siddharth Gupta <sidgup@codeaurora.org>
Link: https://lore.kernel.org/r/1596044401-22083-2-git-send-email-sidgup@codeaurora.org
[bjorn: s/int32_t/s32/ per checkpatch]
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The IPA code now uses the generic remoteproc SSR notification
mechanism. This makes the original IPA notification code unused
and unnecessary, so get rid of it.
This is effectively a revert of commit d7f5f3c89c ("remoteproc:
add IPA notification to q6v5 driver").
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Alex Elder <elder@linaro.org>
Link: https://lore.kernel.org/r/20200724181142.13581-3-elder@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The Texas Instrument's K3 J721E SoCs have a newer next-generation
C71x DSP Subsystem in the MAIN voltage domain in addition to the
previous generation C66x DSP subsystems. The C71x DSP subsystem is
based on the TMS320C71x DSP CorePac module. The C71x CPU is a true
64-bit machine including 64-bit memory addressing and single-cycle
64-bit base arithmetic operations and supports vector signal processing
providing a significant lift in DSP processing power over C66x DSPs.
J721E SoCs use a C711 (a one-core 512-bit vector width CPU core) DSP
that is cache coherent with the A72 Arm cores.
Each subsystem has one or more Fixed/Floating-Point DSP CPUs, with 32 KB
of L1P Cache, 48 KB of L1D SRAM that can be configured and partitioned as
either RAM and/or Cache, and 512 KB of L2 SRAM configurable as either RAM
and/or Cache. The CorePac also includes a Matrix Multiplication Accelerator
(MMA), a Stream Engine (SE) and a C71x Memory Management Unit (CMMU), an
Interrupt Controller (INTC) and a Powerdown Management Unit (PMU) modules.
Update the existing K3 DSP remoteproc driver to add support for this C71x
DSP subsystem. The firmware loading support is provided by using the newly
added 64-bit ELF loader support, and is limited to images using only
external DDR memory at the moment. The L1D and L2 SRAMs are used as scratch
memory when using as RAMs, and cannot be used for loadable segments. The
CMMU is also not supported to begin with, and the driver is designed to
treat the MMU as if it is in bypass mode.
Signed-off-by: Suman Anna <s-anna@ti.com>
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Link: https://lore.kernel.org/r/20200612225357.8251-3-s-anna@ti.com
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The resets for the DSP processors on K3 SoCs are managed through the
Power and Sleep Controller (PSC) module. Each DSP typically has two
resets - a global module reset for powering on the device, and a local
reset that affects only the CPU while allowing access to the other
sub-modules within the DSP processor sub-systems.
The C66x DSPs have two levels of internal RAMs that can be used to
boot from, and the firmware loading into these RAMs require the
local reset to be asserted with the device powered on/enabled using
the module reset. Enhance the K3 DSP remoteproc driver to add support
for loading into the internal RAMs. The local reset is deasserted on
SoC power-on-reset, so logic has to be added in probe in remoteproc
mode to balance the remoteproc state-machine.
Note that the local resets are a no-op on C71x cores, and the hardware
does not supporting loading into its internal RAMs.
Signed-off-by: Suman Anna <s-anna@ti.com>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Link: https://lore.kernel.org/r/20200721223617.20312-7-s-anna@ti.com
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The Texas Instrument's K3 J721E SoCs have two C66x DSP Subsystems in MAIN
voltage domain that are based on the TI's standard TMS320C66x DSP CorePac
module. Each subsystem has a Fixed/Floating-Point DSP CPU, with 32 KB each
of L1P & L1D SRAMs that can be configured and partitioned as either RAM
and/or Cache, and 288 KB of L2 SRAM with 256 KB of memory configurable as
either RAM and/or Cache. The CorePac also includes an Internal DMA (IDMA),
External Memory Controller (EMC), Extended Memory Controller (XMC) with a
Region Address Translator (RAT) unit for 32-bit to 48-bit address
extension/translations, an Interrupt Controller (INTC) and a Powerdown
Controller (PDC).
A new remoteproc module is added to perform the device management of
these DSP devices. The support is limited to images using only external
DDR memory at the moment, the loading support to internal memories and
any on-chip RAM memories will be added in a subsequent patch. RAT support
is also left for a future patch, and as such the reserved memory carveout
regions are all expected to be using memory regions within the first 2 GB.
Error Recovery and Power Management features are not currently supported.
The C66x remote processors do not have an MMU, and so require fixed memory
carveout regions matching the firmware image addresses. Support for this
is provided by mandating multiple memory regions to be attached to the
remoteproc device. The first memory region will be used to serve as the
DMA pool for all dynamic allocations like the vrings and vring buffers.
The remaining memory regions are mapped into the kernel at device probe
time, and are used to provide address translations for firmware image
segments without the need for any RSC_CARVEOUT entries. Any firmware
image using memory outside of the supplied reserved memory carveout
regions will be errored out.
The driver uses various TI-SCI interfaces to talk to the System Controller
(DMSC) for managing configuration, power and reset management of these
cores. IPC between the A72 cores and the DSP cores is supported through
the virtio rpmsg stack using shared memory and OMAP Mailboxes.
Signed-off-by: Suman Anna <s-anna@ti.com>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Link: https://lore.kernel.org/r/20200721223617.20312-6-s-anna@ti.com
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Texas Instruments' K3 generation SoCs have specific modules/register
spaces used for configuring the various aspects of a remote processor.
These include power, reset, boot vector and other configuration features
specific to each compute processor present on the SoC. These registers
are managed by the System Controller such as DMSC on K3 AM65x SoCs.
The Texas Instrument's System Control Interface (TI-SCI) Message Protocol
is used to communicate to the System Controller from various compute
processors to invoke specific services provided by the firmware running
on the System Controller.
Add a common processor control interface header file that can be used by
multiple remoteproc drivers. The helper functions within this header file
abstract the various TI SCI protocol ops for the remoteproc drivers, and
allow them to request the System Controller to be able to program and
manage various remote processors on the SoC. The remoteproc drivers are
expected to manage the life-cycle of their ti_sci_proc_dev local
structures.
Signed-off-by: Suman Anna <s-anna@ti.com>
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Link: https://lore.kernel.org/r/20200721223617.20312-4-s-anna@ti.com
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Add a new helper function rproc_of_parse_firmware() to the remoteproc
core that can be used by various remoteproc drivers to look up the
the "firmware-name" property from a rproc device node. This property
is already being used by multiple drivers, so this helper can avoid
repeating equivalent code in remoteproc drivers.
Signed-off-by: Suman Anna <s-anna@ti.com>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Link: https://lore.kernel.org/r/20200721223617.20312-3-s-anna@ti.com
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Remove the redundant running state, as an equivalent is maintained in
the common q6v5 resource handling helpers.
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Evan Green <evgreen@chromium.org>
Signed-off-by: Sibi Sankar <sibis@codeaurora.org>
Link: https://lore.kernel.org/r/20200602163257.26978-2-sibis@codeaurora.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Sometimes the stop triggers a watchdog rather than a stop-ack. Update
the running state to false on requesting stop to skip the watchdog
instead.
Error Logs:
$ echo stop > /sys/class/remoteproc/remoteproc0/state
ipa 1e40000.ipa: received modem stopping event
remoteproc-modem: watchdog received: sys_m_smsm_mpss.c:291:APPS force stop
qcom-q6v5-mss 4080000.remoteproc-modem: port failed halt
ipa 1e40000.ipa: received modem offline event
remoteproc0: stopped remote processor 4080000.remoteproc-modem
Reviewed-by: Evan Green <evgreen@chromium.org>
Fixes: 3b415c8fb2 ("remoteproc: q6v5: Extract common resource handling")
Cc: stable@vger.kernel.org
Signed-off-by: Sibi Sankar <sibis@codeaurora.org>
Link: https://lore.kernel.org/r/20200602163257.26978-1-sibis@codeaurora.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Add modem debug policy support which will enable coredumps and live
debug support when the msadp firmware is present on secure devices.
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Sibi Sankar <sibis@codeaurora.org>
Link: https://lore.kernel.org/r/20200722201047.12975-4-sibis@codeaurora.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The following mem abort is observed when one of the modem blob firmware
size exceeds the allocated mpss region. Fix this by restricting the copy
size to segment size using request_firmware_into_buf before load.
Err Logs:
Unable to handle kernel paging request at virtual address
Mem abort info:
...
Call trace:
__memcpy+0x110/0x180
rproc_start+0xd0/0x190
rproc_boot+0x404/0x550
state_store+0x54/0xf8
dev_attr_store+0x44/0x60
sysfs_kf_write+0x58/0x80
kernfs_fop_write+0x140/0x230
vfs_write+0xc4/0x208
ksys_write+0x74/0xf8
...
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Fixes: 051fb70fd4 ("remoteproc: qcom: Driver for the self-authenticating Hexagon v5")
Cc: stable@vger.kernel.org
Signed-off-by: Sibi Sankar <sibis@codeaurora.org>
Link: https://lore.kernel.org/r/20200722201047.12975-3-sibis@codeaurora.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The following mem abort is observed when the mba firmware size exceeds
the allocated mba region. MBA firmware size is restricted to a maximum
size of 1M and remaining memory region is used by modem debug policy
firmware when available. Hence verify whether the MBA firmware size lies
within the allocated memory region and is not greater than 1M before
loading.
Err Logs:
Unable to handle kernel paging request at virtual address
Mem abort info:
...
Call trace:
__memcpy+0x110/0x180
rproc_start+0x40/0x218
rproc_boot+0x5b4/0x608
state_store+0x54/0xf8
dev_attr_store+0x44/0x60
sysfs_kf_write+0x58/0x80
kernfs_fop_write+0x140/0x230
vfs_write+0xc4/0x208
ksys_write+0x74/0xf8
__arm64_sys_write+0x24/0x30
...
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Fixes: 051fb70fd4 ("remoteproc: qcom: Driver for the self-authenticating Hexagon v5")
Cc: stable@vger.kernel.org
Signed-off-by: Sibi Sankar <sibis@codeaurora.org>
Link: https://lore.kernel.org/r/20200722201047.12975-2-sibis@codeaurora.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
On SC7180 the MBA firmware stores the bootup text logs in a 4K segment
at the beginning of the MBA region. Add support to extract the logs
which will be useful to debug mba boot/authentication issues.
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Sibi Sankar <sibis@codeaurora.org>
Link: https://lore.kernel.org/r/20200721112935.25716-3-sibis@codeaurora.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Add coredump debugfs entry to configure the type of dump that will
be collected during recovery. User can select between default or
inline coredump functionality. Also coredump collection can be
disabled through this interface.
This functionality can be configured differently for different
remote processors.
Signed-off-by: Rishabh Bhatnagar <rishabhb@codeaurora.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Tested-by: Sibi Sankar <sibis@codeaurora.org>
Reviewed-by: Sibi Sankar <sibis@codeaurora.org>
Link: https://lore.kernel.org/r/1594938035-7327-6-git-send-email-rishabhb@codeaurora.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The current coredump implementation uses vmalloc area to copy
all the segments. But this might put strain on low memory targets
as the firmware size sometimes is in tens of MBs. The situation
becomes worse if there are multiple remote processors undergoing
recovery at the same time. This patch adds inline coredump
functionality that avoids extra memory usage. This requires
recovery to be halted until data is read by userspace and free
function is called.
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Sibi Sankar <sibis@codeaurora.org>
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Rishabh Bhatnagar <rishabhb@codeaurora.org>
Tested-by: Sibi Sankar <sibis@codeaurora.org>
Link: https://lore.kernel.org/r/1594938035-7327-5-git-send-email-rishabhb@codeaurora.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Change the segment dump API signature to include size and offset
arguments. Refactor the qcom_q6v5_mss driver to use these
arguments while copying the segment. Doing this lays the ground
work for "inline" coredump functionality being added in the next
patch.
Tested-by: Sibi Sankar <sibis@codeaurora.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Sibi Sankar <sibis@codeaurora.org>
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Rishabh Bhatnagar <rishabhb@codeaurora.org>
Link: https://lore.kernel.org/r/1594938035-7327-4-git-send-email-rishabhb@codeaurora.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
In order to land inline coredump support for mss, the dump_segment
function would need to support granularities less than the segment
size. This is achieved by replacing mask based tracking with size.
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Sibi Sankar <sibis@codeaurora.org>
Signed-off-by: Rishabh Bhatnagar <rishabhb@codeaurora.org>
Link: https://lore.kernel.org/r/1594938035-7327-3-git-send-email-rishabhb@codeaurora.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Move all coredump functionality to an individual file. This is
being done so that the current functionality can be extended
in future patchsets.
Signed-off-by: Rishabh Bhatnagar <rishabhb@codeaurora.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Reviewed-by: Sibi Sankar <sibis@codeaurora.org>
Tested-by: Sibi Sankar <sibis@codeaurora.org>
Link: https://lore.kernel.org/r/1594938035-7327-2-git-send-email-rishabhb@codeaurora.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Split function stm32_rproc_parse_fw() in two parts, the first one
to parse the memory regions and the second one to load the
resource table. That way parsing of the memory regions can be
done without having do deal with the resource table when attaching
to a remote processor.
Mainly based on the work published by Arnaud Pouliquen [1].
[1]. https://patchwork.kernel.org/project/linux-remoteproc/list/?series=239877
Acked-by: Arnaud Pouliquen <arnaud.pouliquen@st.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Link: https://lore.kernel.org/r/20200714200445.1427257-9-mathieu.poirier@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Make function rproc_resource_cleanup() public so that it can be
used by platform drivers when allocating resources to be used by
a detached remote processor.
Acked-by: Arnaud Pouliquen <arnaud.pouliquen@st.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Link: https://lore.kernel.org/r/20200714200445.1427257-8-mathieu.poirier@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Introduce the required mechanic to set the state of the M4 in order
to properly deal with scenarios where the co-processor has been
started by another entity.
Mainly based on the work published by Arnaud Pouliquen [1].
[1]. https://patchwork.kernel.org/project/linux-remoteproc/list/?series=239877
Acked-by: Arnaud Pouliquen <arnaud.pouliquen@st.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20200714200445.1427257-7-mathieu.poirier@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Get from the DT the syncon to probe the state of the remote processor
and the location of the resource table.
Mainly based on the work published by Arnaud Pouliquen [1].
[1]. https://patchwork.kernel.org/project/linux-remoteproc/list/?series=239877
Acked-by: Arnaud Pouliquen <arnaud.pouliquen@st.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Reviewed-by: Loic Pallardy <loic.pallardy@st.com>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20200714200445.1427257-6-mathieu.poirier@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Other than one has to be done after the other, there is no correlation
between memory translation and DT parsing. As such move function
stm32_rproc_of_memory_translations() to stm32_rproc_probe() so that
stm32_rproc_parse_dt() can be extended to look for attach bindings
in a clean way.
Acked-by: Arnaud Pouliquen <arnaud.pouliquen@st.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Reviewed-by: Loic Pallardy <loic.pallardy@st.com>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20200714200445.1427257-5-mathieu.poirier@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Remove the remote processor from the process of parsing the device tree
since (1) there is no correlation between them and (2) to use the
information that was gathered to make a decision on whether to
synchronise with the M4 or not.
Acked-by: Arnaud Pouliquen <arnaud.pouliquen@st.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20200714200445.1427257-4-mathieu.poirier@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Request IRQ with platform device rather than remote proc in order to
call stm32_rproc_parse_dt() before rproc_alloc(). That way we can
know whether we need to synchronise with the MCU or not.
Acked-by: Arnaud Pouliquen <arnaud.pouliquen@st.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Reviewed-by: Loic Pallardy <loic.pallardy@st.com>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20200714200445.1427257-3-mathieu.poirier@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Remove the remote processor from the process of parsing the memory
ranges since there is no correlation between them.
Acked-by: Arnaud Pouliquen <arnaud.pouliquen@st.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Reviewed-by: Loic Pallardy <loic.pallardy@st.com>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20200714200445.1427257-2-mathieu.poirier@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
This patch prevents the firmware image name from being displayed when
the remoteproc core is attaching to a remote processor. This is needed
needed since there is no guarantee about the nature of the firmware
image that is loaded by the external entity.
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Reviewed-by: Arnaud Pouliquen <arnaud.pouliquen@st.com>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Tested-by: Arnaud Pouliquen <arnaud.pouliquen@st.com>
Link: https://lore.kernel.org/r/20200714195035.1426873-10-mathieu.poirier@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
When function rproc_free_vring() clears the virtio device section
it does so on the cached resource table rather than the one
installed in the remote processor memory. When a remote processor
has been booted by another entity there is no need to use a cached
table and as such, no need to clear the virtio device section in
it.
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Tested-by: Arnaud Pouliquen <arnaud.pouliquen@st.com>
Link: https://lore.kernel.org/r/20200714195035.1426873-9-mathieu.poirier@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Refactor function rproc_trigger_auto_boot() to properly deal
with scenarios where the remoteproc core needs to attach with a
remote processor that has already been booted by an external
entity.
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Tested-by: Arnaud Pouliquen <arnaud.pouliquen@st.com>
Link: https://lore.kernel.org/r/20200714195035.1426873-8-mathieu.poirier@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Refactor function rproc_boot() to properly deal with scenarios
where the remoteproc core needs to attach with a remote
processor that has already been booted by an external entity.
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Tested-by: Arnaud Pouliquen <arnaud.pouliquen@st.com>
Link: https://lore.kernel.org/r/20200714195035.1426873-7-mathieu.poirier@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Add a new function to assert the general health of the remote
processor before handing it to the remoteproc core.
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Reviewed-by: Arnaud Pouliquen <arnaud.pouliquen@st.com>
Tested-by: Arnaud Pouliquen <arnaud.pouliquen@st.com>
Link: https://lore.kernel.org/r/20200714195035.1426873-6-mathieu.poirier@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Introduce function rproc_actuate() that provides the same
functionatlity as rproc_fw_boot(), but without the steps that
involve interaction with the firmware image. That way we can
deal with scenarios where the remoteproc core is attaching
to a remote processor that has already been started by another
entity.
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Reviewed-by: Arnaud Pouliquen <arnaud.pouliquen@st.com>
Tested-by: Arnaud Pouliquen <arnaud.pouliquen@st.com>
Link: https://lore.kernel.org/r/20200714195035.1426873-5-mathieu.poirier@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Introducing function rproc_attach() to enact the same actions as
rproc_start(), but without the steps related to the handling of
a firmware image. That way we can properly deal with scenarios
where the remoteproc core needs to attach with a remote processsor
that has been booted by another entity.
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Tested-by: Arnaud Pouliquen <arnaud.pouliquen@st.com>
Link: https://lore.kernel.org/r/20200714195035.1426873-4-mathieu.poirier@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Add an new attach() operation in order to properly deal with
scenarios where the remoteproc core needs to attach to a
remote processor that has been booted by another entity.
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Tested-by: Arnaud Pouliquen <arnaud.pouliquen@st.com>
Link: https://lore.kernel.org/r/20200714195035.1426873-3-mathieu.poirier@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Add a new RPROC_DETACHED state to take into account scenarios
where the remoteproc core needs to attach to a remote processor
that is booted by another entity.
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Tested-by: Arnaud Pouliquen <arnaud.pouliquen@st.com>
Link: https://lore.kernel.org/r/20200714195035.1426873-2-mathieu.poirier@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
On secure devices there exists a race condition which could lock the MSS
CONFIG AHB bus thus preventing access to BOOT_STATUS register during SSR.
Switch to polling the MSS_STATUS register with an additional 10 us delay
to reliably track boot completion.
Signed-off-by: Sibi Sankar <sibis@codeaurora.org>
Link: https://lore.kernel.org/r/20200716120514.21588-1-sibis@codeaurora.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
On platforms with 32-bit phys_addr_t the shift to get the upper word of
the base address of the memory region is invalid. Cast the base to 64
bit to resolv this.
Fixes: 549b67da66 ("remoteproc: qcom: Introduce helper to store pil info in IMEM")
Tested-by: Nathan Chancellor <natechancellor@gmail.com> # build
Reported-by: Lee Jones <lee.jones@linaro.org>
Reported-by: Nathan Chancellor <natechancellor@gmail.com>
Link: https://lore.kernel.org/r/20200716054817.157608-1-bjorn.andersson@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Looks as though 'name' has now been moved into 'struct sysmod_event'
which is passed in instead. However, the parameter descriptions were
not updated at the same time. Let's do that now.
Fixes the following W=1 kernel build warning(s):
drivers/remoteproc/qcom_sysmon.c:78: warning: Function parameter or member 'event' not described in 'sysmon_send_event'
drivers/remoteproc/qcom_sysmon.c:78: warning: Excess function parameter 'name' description in 'sysmon_send_event'
drivers/remoteproc/qcom_sysmon.c:350: warning: Function parameter or member 'event' not described in 'ssctl_send_event'
drivers/remoteproc/qcom_sysmon.c:350: warning: Excess function parameter 'name' description in 'ssctl_send_event'
Cc: Andy Gross <agross@kernel.org>
Cc: linux-arm-msm@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20200715123551.4011154-2-lee.jones@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Fixes the following W=1 kernel build warning(s):
drivers/remoteproc/remoteproc_core.c: In function ‘rproc_find_carveout_by_name’:
drivers/remoteproc/remoteproc_core.c:257:2: warning: function ‘rproc_find_carveout_by_name’ might be a candidate for ‘gnu_printf’ format attribute [-Wsuggest-attribute=format]
257 | vsnprintf(_name, sizeof(_name), name, args);
| ^~~~~~~~~
drivers/remoteproc/remoteproc_core.c: In function ‘rproc_mem_entry_init’:
drivers/remoteproc/remoteproc_core.c:993:2: warning: function ‘rproc_mem_entry_init’ might be a candidate for ‘gnu_printf’ format attribute [-Wsuggest-attribute=format]
993 | vsnprintf(mem->name, sizeof(mem->name), name, args);
| ^~~~~~~~~
drivers/remoteproc/remoteproc_core.c: In function ‘rproc_of_resm_mem_entry_init’:
drivers/remoteproc/remoteproc_core.c:1029:2: warning: function ‘rproc_of_resm_mem_entry_init’ might be a candidate for ‘gnu_printf’ format attribute [-Wsuggest-attribute=format]
1029 | vsnprintf(mem->name, sizeof(mem->name), name, args);
| ^~~~~~~~~
Cc: Brian Swetland <swetland@google.com>
Cc: Mark Grosen <mgrosen@ti.com>
Cc: Guzman Lugo <fernando.lugo@ti.com>
Cc: Suman Anna <s-anna@ti.com>
Cc: Robert Tivy <rtivy@ti.com>
Cc: De Leon <x0095078@ti.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20200715123551.4011154-1-lee.jones@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
drivers/remoteproc/qcom_common.c: In function 'qcom_ssr_get_subsys':
drivers/remoteproc/qcom_common.c:210:9: error: implicit declaration of function 'kzalloc'; did you mean 'vzalloc'?
[-Werror=implicit-function-declaration]
info = kzalloc(sizeof(*info), GFP_KERNEL);
^~~~~~~
vzalloc
kzalloc() is declared in linux/slab.h, add include to fix build issue.
Tested-by: Alex Elder <elder@linaro.org>
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Kefeng Wang <wangkefeng.wang@huawei.com>
Link: https://lore.kernel.org/r/20200713020003.134039-1-wangkefeng.wang@huawei.com
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The SSR subdevice only adds callback for the unprepare event. Add callbacks
for prepare, start and prepare events. The client driver for a particular
remoteproc might be interested in knowing the status of the remoteproc
while undergoing SSR, not just when the remoteproc has finished shutting
down.
Reviewed-by: Alex Elder <elder@linaro.org>
Signed-off-by: Siddharth Gupta <sidgup@codeaurora.org>
Signed-off-by: Rishabh Bhatnagar <rishabhb@codeaurora.org>
Link: https://lore.kernel.org/r/1592965408-16908-3-git-send-email-rishabhb@codeaurora.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Currently there is a single notification chain which is called whenever any
remoteproc shuts down. This leads to all the listeners being notified, and
is not an optimal design as kernel drivers might only be interested in
listening to notifications from a particular remoteproc. Create a global
list of remoteproc notification info data structures. This will hold the
name and notifier_list information for a particular remoteproc. The API
to register for notifications will use name argument to retrieve the
notification info data structure and the notifier block will be added to
that data structure's notification chain. Also move from blocking notifier
to srcu notifer based implementation to support dynamic notifier head
creation.
Reviewed-by: Alex Elder <elder@linaro.org>
Co-developed-by: Siddharth Gupta <sidgup@codeaurora.org>
Signed-off-by: Siddharth Gupta <sidgup@codeaurora.org>
Signed-off-by: Rishabh Bhatnagar <rishabhb@codeaurora.org>
Link: https://lore.kernel.org/r/1592965408-16908-2-git-send-email-rishabhb@codeaurora.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Update the PIL relocation information in IMEM with information about
where the firmware for various remoteprocs are loaded.
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20200622191942.255460-4-bjorn.andersson@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
A region in IMEM is used to communicate load addresses of remoteproc to
post mortem debug tools. Implement a helper function that can be used to
store this information in order to enable these tools to process
collected ramdumps.
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20200622191942.255460-3-bjorn.andersson@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
This reverts commit a99a37f6cd.
Removing PM runtime operations from the remoteproc core in order to:
1) Keep all power management operations in platform drivers. That way we
do not loose flexibility in an area that is very HW specific.
2) Avoid making the support for remote processor managed by external
entities more complex that it already is.
3) Fix regression introduced for the Omap remoteproc driver.
Acked-by: Suman Anna <s-anna@ti.com>
Tested-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Link: https://lore.kernel.org/r/20200630163118.3830422-3-mathieu.poirier@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The header file linux/uio.h includes crypto/hash.h which pulls in
most of the Crypto API. Since linux/uio.h is used throughout the
kernel this means that every tiny bit of change to the Crypto API
causes the entire kernel to get rebuilt.
This patch fixes this by moving it into lib/iov_iter.c instead
where it is actually used.
This patch also fixes the ifdef to use CRYPTO_HASH instead of just
CRYPTO which does not guarantee the existence of ahash.
Unfortunately a number of drivers were relying on linux/uio.h to
provide access to linux/slab.h. This patch adds inclusions of
linux/slab.h as detected by build failures.
Also skbuff.h was relying on this to provide a declaration for
ahash_request. This patch adds a forward declaration instead.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
This introduces device managed versions of functions used to register
remoteproc devices, add support for remoteproc driver specific resource
control, enables remoteproc drivers to specify ELF class and machine for
coredumps. It integrates pm_runtime in the core for keeping resources
active while the remote is booted and holds a wake source while
recoverying a remote processor after a firmware crash.
It refactors the remoteproc device's allocation path to simplify the
logic, fix a few cleanup bugs and to not clone const strings onto the
heap. Debugfs code is simplifies using the DEFINE_SHOW_ATTRIBUTE and a
zero-length array is replaced with flexible-array.
A new remoteproc driver for the JZ47xx VPU is introduced, the Qualcomm
SM8250 gains support for audio, compute and sensor remoteprocs and the
Qualcomm SC7180 modem support is cleaned up and improved.
The Qualcomm glink subsystem-restart driver is merged into the main
glink driver, the Qualcomm sysmon driver is extended to properly notify
remote processors about all other remote processors' state transitions.
-----BEGIN PGP SIGNATURE-----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=4k54
-----END PGP SIGNATURE-----
Merge tag 'rproc-v5.8' of git://git.kernel.org/pub/scm/linux/kernel/git/andersson/remoteproc
Pull remoteproc updates from Bjorn Andersson:
"This introduces device managed versions of functions used to register
remoteproc devices, add support for remoteproc driver specific
resource control, enables remoteproc drivers to specify ELF class and
machine for coredumps. It integrates pm_runtime in the core for
keeping resources active while the remote is booted and holds a wake
source while recoverying a remote processor after a firmware crash.
It refactors the remoteproc device's allocation path to simplify the
logic, fix a few cleanup bugs and to not clone const strings onto the
heap. Debugfs code is simplifies using the DEFINE_SHOW_ATTRIBUTE and a
zero-length array is replaced with flexible-array.
A new remoteproc driver for the JZ47xx VPU is introduced, the Qualcomm
SM8250 gains support for audio, compute and sensor remoteprocs and the
Qualcomm SC7180 modem support is cleaned up and improved.
The Qualcomm glink subsystem-restart driver is merged into the main
glink driver, the Qualcomm sysmon driver is extended to properly
notify remote processors about all other remote processors' state
transitions"
* tag 'rproc-v5.8' of git://git.kernel.org/pub/scm/linux/kernel/git/andersson/remoteproc: (43 commits)
remoteproc: Fix an error code in devm_rproc_alloc()
MAINTAINERS: Add myself as reviewer for Ingenic rproc driver
remoteproc: ingenic: Added remoteproc driver
remoteproc: Add support for runtime PM
dt-bindings: Document JZ47xx VPU auxiliary processor
remoteproc: wcss: Fix arguments passed to qcom_add_glink_subdev()
remoteproc: Fix and restore the parenting hierarchy for vdev
remoteproc: Fall back to using parent memory pool if no dedicated available
remoteproc: Replace zero-length array with flexible-array
remoteproc: wcss: add support for rpmsg communication
remoteproc: core: Prevent system suspend during remoteproc recovery
remoteproc: qcom_q6v5_mss: Remove unused q6v5_da_to_va function
remoteproc: qcom_q6v5_mss: map/unmap mpss segments before/after use
remoteproc: qcom_q6v5_mss: Drop accesses to MPSS PERPH register space
dt-bindings: remoteproc: qcom: Replace halt-nav with spare-regs
remoteproc: qcom: pas: Add SM8250 PAS remoteprocs
dt-bindings: remoteproc: qcom: pas: Add SM8250 remoteprocs
remoteproc: qcom_q6v5_mss: Extract mba/mpss from memory-region
dt-bindings: remoteproc: qcom: Use memory-region to reference memory
remoteproc: qcom: pas: Add SC7180 Modem support
...
The comments say that this function should return NULL on error and the
caller expects NULL returns as well so I have modified the code to match.
Returning an ERR_PTR(-ENOMEM) would lead to an OOps.
Reviewed-by: Paul Cercueil <paul@crapouillou.net>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Fixes: 305ac5a766 ("remoteproc: Add device-managed variants of rproc_alloc/rproc_add")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://lore.kernel.org/r/20200520120705.GH172354@mwanda
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
This driver is used to boot, communicate with and load firmwares to the
MIPS co-processor found in the VPU hardware of the JZ47xx SoCs from
Ingenic.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Acked-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Link: https://lore.kernel.org/r/20200515104340.10473-4-paul@crapouillou.net
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Call pm_runtime_get_sync() before the firmware is loaded, and
pm_runtime_put() after the remote processor has been stopped.
Even though the remoteproc device has no PM callbacks, this allows the
parent device's PM callbacks to be properly called.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Link: https://lore.kernel.org/r/20200515104340.10473-3-paul@crapouillou.net
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Recently qcom_add_glink_subdev() was extended to also take the glink_ssr
identifier as an argument and I missed this while applying '8a226e2c71bb
("remoteproc: wcss: add support for rpmsg communication")'.
Fixes: 8a226e2c71 ("remoteproc: wcss: add support for rpmsg communication")
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20200514185856.1598945-1-bjorn.andersson@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The commit 086d08725d ("remoteproc: create vdev subdevice with specific
dma memory pool") has introduced a new vdev subdevice for each vdev
declared in the firmware resource table and made it as the parent for the
created virtio rpmsg devices instead of the previous remoteproc device.
This changed the overall parenting hierarchy for the rpmsg devices, which
were children of virtio devices, and does not allow the corresponding
rpmsg drivers to retrieve the parent rproc device through the
rproc_get_by_child() API.
Fix this by restoring the remoteproc device as the parent. The new vdev
subdevice can continue to inherit the DMA attributes from the remoteproc's
parent device (actual platform device).
Cc: stable@vger.kernel.org
Fixes: 086d08725d ("remoteproc: create vdev subdevice with specific dma memory pool")
Signed-off-by: Suman Anna <s-anna@ti.com>
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Acked-by: Arnaud Pouliquen <arnaud.pouliquen@st.com>
Link: https://lore.kernel.org/r/20200420160600.10467-3-s-anna@ti.com
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
In some cases, like with OMAP remoteproc, we are not creating dedicated
memory pool for the virtio device. Instead, we use the same memory pool
for all shared memories. The current virtio memory pool handling forces
a split between these two, as a separate device is created for it,
causing memory to be allocated from bad location if the dedicated pool
is not available. Fix this by falling back to using the parent device
memory pool if dedicated is not available.
Cc: stable@vger.kernel.org
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Acked-by: Arnaud Pouliquen <arnaud.pouliquen@st.com>
Fixes: 086d08725d ("remoteproc: create vdev subdevice with specific dma memory pool")
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Suman Anna <s-anna@ti.com>
Link: https://lore.kernel.org/r/20200420160600.10467-2-s-anna@ti.com
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The system might go into suspend during recovery of any remoteproc.
This will interrupt the recovery process in between increasing the
recovery time. Make the platform device as wakeup capable and
use pm_stay_wake/pm_relax APIs to avoid system from going into
suspend during recovery.
Signed-off-by: Siddharth Gupta <sidgup@codeaurora.org>
Signed-off-by: Rishabh Bhatnagar <rishabhb@codeaurora.org>
Acked-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Link: https://lore.kernel.org/r/1588183482-21146-1-git-send-email-rishabhb@codeaurora.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Remove unsed q6v5_da_to_va function as the mss driver uses a per segment
dump function.
Tested-by: Evan Green <evgreen@chromium.org>
Signed-off-by: Sibi Sankar <sibis@codeaurora.org>
Link: https://lore.kernel.org/r/20200415071619.6052-2-sibis@codeaurora.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The application processor accessing the mpss region when the Q6 modem is
running will lead to an XPU violation. Fix this by un-mapping the mpss
segments post copy during mpss authentication and coredumps.
Tested-by: Evan Green <evgreen@chromium.org>
Signed-off-by: Sibi Sankar <sibis@codeaurora.org>
Link: https://lore.kernel.org/r/20200415071619.6052-1-sibis@codeaurora.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
7C retail devices using MSA based boot will result in a fuse combination
which will prevent accesses to MSS PERPH register space where the mpss
clocks and halt-nav reside. So drop all accesses to the MPSS PERPH
register space. Issuing HALT NAV request and turning on the mss clocks
as part of SSR will no longer be required since the modem firmware will
have the necessary fixes to ensure that there are no pending NAV DMA
transactions.
Tested-by: Evan Green <evgreen@chromium.org>
Signed-off-by: Sibi Sankar <sibis@codeaurora.org>
Link: https://lore.kernel.org/r/20200415145110.20624-3-sibis@codeaurora.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
In the absence of mba and mpss sub-child extract the mba/mpss regions
from the memory-region property.
Tested-by: Evan Green <evgreen@chromium.org>
Signed-off-by: Sibi Sankar <sibis@codeaurora.org>
Link: https://lore.kernel.org/r/20200421143228.8981-5-sibis@codeaurora.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Add support for booting the Modem DSP found on Qualcomm's SC7180 SoCs.
Tested-by: Evan Green <evgreen@chromium.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Sibi Sankar <sibis@codeaurora.org>
Link: https://lore.kernel.org/r/20200421143228.8981-3-sibis@codeaurora.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
sizeof() when applied to a pointer typed expression gives the
size of the pointer, not that of the pointed data.
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Fixes: 63c13d61ea ("remoteproc/mediatek: add SCP support for mt8183")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Link: https://lore.kernel.org/r/20200509084237.36293-1-weiyongjun1@huawei.com
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Rather than carrying a special purpose blocking notifier for glink_ssr
in remoteproc's qcom_common.c, move it into glink_ssr so allow wider
reuse of the common one.
The rpmsg glink header file is used in preparation for the next patch.
Acked-by: Chris Lew <clew@codeaurora.org>
Acked-by: Rishabh Bhatnagar <rishabhb@codeaurora.org>
Link: https://lore.kernel.org/r/20200423003736.2027371-3-bjorn.andersson@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Pass ssr_name to glink subdevice in preparation for tying glink_ssr to
the glink subdevice, rather than having its own "ssr subdevice".
Acked-by: Chris Lew <clew@codeaurora.org>
Acked-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Acked-by: Rishabh Bhatnagar <rishabhb@codeaurora.org>
Link: https://lore.kernel.org/r/20200423003736.2027371-2-bjorn.andersson@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
This fixes a regression in the probe error path of the Qualcomm modem
remoteproc driver and a mix up of phy_addr_t and dma_addr_t in the
Mediatek SCP control driver.
-----BEGIN PGP SIGNATURE-----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=WDtr
-----END PGP SIGNATURE-----
Merge tag 'rproc-v5.7-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/andersson/remoteproc
Pull remoteproc fixes from Bjorn Andersson:
"This fixes a regression in the probe error path of the Qualcomm modem
remoteproc driver and a mix up of phy_addr_t and dma_addr_t in the
Mediatek SCP control driver"
* tag 'rproc-v5.7-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/andersson/remoteproc:
remoteproc: mtk_scp: use dma_addr_t for DMA API
remoteproc: qcom_q6v5_mss: fix q6v5_probe() error paths
remoteproc: qcom_q6v5_mss: fix a bug in q6v5_probe()
Message logged by 'dev_xxx()' or 'pr_xxx()' should end with a '\n'.
Fixes: 791c13b709 ("remoteproc: Fix NULL pointer dereference in rproc_virtio_notify")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/20200411160750.32573-1-christophe.jaillet@wanadoo.fr
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
On some SoC architecture, it is needed to enable HW like
clock, bus, regulator, memory region... before loading
co-processor firmware.
This patch introduces prepare and unprepare ops to execute
platform specific function before firmware loading and after
stop execution.
Signed-off-by: Loic Pallardy <loic.pallardy@st.com>
Signed-off-by: Suman Anna <s-anna@ti.com>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Link: https://lore.kernel.org/r/20200417002036.24359-2-s-anna@ti.com
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Since checks are present in the remoteproc elf loader before calling
da_to_va, loading a elf64 will work on 32bits flavors of kernel.
Indeed, if a segment size is larger than what size_t can hold, the
loader will return an error so the functionality is equivalent to
what exists today.
Acked-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Clement Leger <cleger@kalray.eu>
Link: https://lore.kernel.org/r/20200422093017.10985-1-cleger@kalray.eu
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Add API functions devm_rproc_alloc() and devm_rproc_add(), which behave
like rproc_alloc() and rproc_add() respectively, but register their
respective cleanup function to be called on driver detach.
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Link: https://lore.kernel.org/r/20200417170040.174319-2-paul@crapouillou.net
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The current name field used in the remoteproc structure is simply
a pointer to a name field supplied during the rproc_alloc() call.
The pointer passed in by remoteproc drivers during registration is
typically a dev_name pointer, but it is possible that the pointer
will no longer remain valid if the devices themselves were created
at runtime like in the case of of_platform_populate(), and were
deleted upon any failures within the respective remoteproc driver
probe function.
So, allocate and maintain a local copy for this name field to
keep it agnostic of the logic used in the remoteproc drivers.
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Suman Anna <s-anna@ti.com>
Link: https://lore.kernel.org/r/20200417002036.24359-3-s-anna@ti.com
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Get rid of tedious error management by moving firmware and operation
allocation after calling device_initialize(). That way we take advantage
of the automatic call to rproc_type_release() to cleanup after ourselves
when put_device() is called.
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Reviewed-by: Alex Elder <elder@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Acked-by: Suman Anna <s-anna@ti.com>
Link: https://lore.kernel.org/r/20200420231601.16781-5-mathieu.poirier@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Make the rproc_ops allocation a function on its own in an effort
to clean up function rproc_alloc().
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Reviewed-by: Alex Elder <elder@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20200420231601.16781-4-mathieu.poirier@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Improve the readability of function rproc_alloc_firmware() by using
a non-negated condition and moving the comment out of the conditional
block
Suggested-by: Alex Elder <elder@linaro.org>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Reviewed-by: Alex Elder <elder@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20200420231601.16781-3-mathieu.poirier@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
For cases where @firmware is declared "const char *", use function
kstrdup_const() to avoid needlessly creating another copy on the
heap.
Suggested-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Reviewed-by: Alex Elder <elder@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20200420231601.16781-2-mathieu.poirier@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Clients/services running on a remoteproc that booted up might need to be
aware of the state of already running remoteprocs. When a remoteproc boots
up (fresh or after recovery) it is not aware of the remoteprocs that booted
before it, i.e., the system state is incomplete. So to keep track of it we
send sysmon on behalf of all 'ONLINE' remoteprocs.
Acked-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Siddharth Gupta <sidgup@codeaurora.org>
Link: https://lore.kernel.org/r/1586389003-26675-4-git-send-email-sidgup@codeaurora.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Add notification for other stages of remoteproc boot and shutdown. This
includes adding callback functions for the prepare and unprepare events,
and fleshing out the callback function for start.
Acked-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Siddharth Gupta <sidgup@codeaurora.org>
Link: https://lore.kernel.org/r/1586389003-26675-3-git-send-email-sidgup@codeaurora.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Current implementation of the sysmon driver does not support adding
notifications for other remoteproc events - prepare, start, unprepare.
Clients on the remoteproc side might be interested in knowing when a
remoteproc boots up. This change adds the ability to send the notification
type along with the name. For example, audio DSP is interested in knowing
when modem has crashed so that it can perform cleanup and wait for modem to
boot up before it starts processing data again.
Acked-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Siddharth Gupta <sidgup@codeaurora.org>
Link: https://lore.kernel.org/r/1586389003-26675-2-git-send-email-sidgup@codeaurora.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Modify drivers which are using remoteproc coredump functionality to use
rproc_coredump_set_elf_info in order to create correct elf coredump
format.
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Clement Leger <cleger@kalray.eu>
Link: https://lore.kernel.org/r/20200410102433.2672-3-cleger@kalray.eu
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
In an effort to cleanup firmware name allocation, replace the
cumbersome mechanic used to allocate a default firmware name with
function kasprintf().
Reviewed-by: Alex Elder <elder@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Suggested-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Link: https://lore.kernel.org/r/20200415204858.2448-4-mathieu.poirier@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
