This patch is changing the simple workqueue in the gadget driver to be
allocated as async_wq with a higher priority. The pump worker, that is
filling the usb requests, will have a higher priority and will not be
scheduled away so often while the video stream is handled. This will
lead to fewer streaming underruns.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Link: https://lore.kernel.org/r/20220907215818.2670097-1-m.grzeschik@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 6a108a14fa ("kconfig: rename CONFIG_EMBEDDED to CONFIG_EXPERT")
introduces CONFIG_EXPERT to carry the previous intent of CONFIG_EMBEDDED
and just gives that intent a much better name. That has been clearly a good
and long overdue renaming, and it is clearly an improvement to the kernel
build configuration that has shown to help managing the kernel build
configuration in the last decade.
However, rather than bravely and radically just deleting CONFIG_EMBEDDED,
this commit gives CONFIG_EMBEDDED a new intended semantics, but keeps it
open for future contributors to implement that intended semantics:
A new CONFIG_EMBEDDED option is added that automatically selects
CONFIG_EXPERT when enabled and can be used in the future to isolate
options that should only be considered for embedded systems (RISC
architectures, SLOB, etc).
Since then, this CONFIG_EMBEDDED implicitly had two purposes:
- It can make even more options visible beyond what CONFIG_EXPERT makes
visible. In other words, it may introduce another level of enabling the
visibility of configuration options: always visible, visible with
CONFIG_EXPERT and visible with CONFIG_EMBEDDED.
- Set certain default values of some configurations differently,
following the assumption that configuring a kernel build for an
embedded system generally starts with a different set of default values
compared to kernel builds for all other kind of systems.
Considering the first purpose, at the point in time where CONFIG_EMBEDDED
was renamed to CONFIG_EXPERT, CONFIG_EXPERT already made 130 more options
become visible throughout all different menus for the kernel configuration.
Over the last decade, this has gradually increased, so that currently, with
CONFIG_EXPERT, roughly 170 more options become visible throughout all
different menus for the kernel configuration. In comparison, currently with
CONFIG_EMBEDDED enabled, just seven more options are visible, one in x86,
one in arm, and five for the ChipIdea Highspeed Dual Role Controller.
As the numbers suggest, these two levels of enabling the visibility of even
more configuration options---beyond what CONFIG_EXPERT enables---never
evolved to a good solution in the last decade. In other words, this
additional level of visibility of configuration option with CONFIG_EMBEDDED
compared to CONFIG_EXPERT has since its introduction never become really
valuable. It requires quite some investigation to actually understand what
is additionally visible and it does not differ significantly in complexity
compared to just enabling CONFIG_EXPERT. This CONFIG_EMBEDDED---or any
other config to show more detailed options beyond CONFIG_EXPERT---is
unlikely to be valuable unless somebody puts significant effort in
identifying how such visibility options can be properly split and creating
clear criteria, when some config option is visible with CONFIG_EXPERT and
when some config option is visible only with some further option enabled
beyond CONFIG_EXPERT, such as CONFIG_EMBEDDED attempted to do. For now, it
is much more reasonable to simply make those additional seven options that
visible with CONFIG_EMBEDDED, visible with CONFIG_EXPERT, and then remove
CONFIG_EMBEDDED. If anyone spends significant effort in structuring the
visibility of config options, they may re-introduce suitable new config
options simply as they see fit.
Make the configs for usb chipidea glue drivers visible when CONFIG_EXPERT
is enabled.
Signed-off-by: Lukas Bulwahn <lukas.bulwahn@gmail.com>
Link: https://lore.kernel.org/r/20220908104337.11940-5-lukas.bulwahn@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
During a cable disconnect sequence, if ep0state is not in the SETUP phase,
then nothing will trigger any pending end transfer commands. Force
stopping of any pending SETUP transaction, and move back to the SETUP
phase.
Reviewed-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Signed-off-by: Wesley Cheng <quic_wcheng@quicinc.com>
Link: https://lore.kernel.org/r/20220901193625.8727-6-quic_wcheng@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For endxfer commands that do not require an endpoint complete interrupt,
avoid having to wait for the command active bit to clear. This allows for
EP0 events to continue to be handled, which allows for the controller to
complete it. Otherwise, it is known that the endxfer command will fail if
there is a pending SETUP token that needs to be read.
Suggested-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Reviewed-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Signed-off-by: Wesley Cheng <quic_wcheng@quicinc.com>
Link: https://lore.kernel.org/r/20220901193625.8727-5-quic_wcheng@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since EP0 transactions need to be completed before the controller halt
sequence is finished, this may take some time depending on the host and the
enabled functions. Increase the controller halt timeout, so that we give
the controller sufficient time to handle EP0 transfers.
Signed-off-by: Wesley Cheng <quic_wcheng@quicinc.com>
Link: https://lore.kernel.org/r/20220901193625.8727-4-quic_wcheng@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove the need for making dwc3_gadget_suspend() and dwc3_gadget_resume()
to be called in a spinlock, as dwc3_gadget_run_stop() could potentially
take some time to complete.
Signed-off-by: Wesley Cheng <quic_wcheng@quicinc.com>
Link: https://lore.kernel.org/r/20220901193625.8727-3-quic_wcheng@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If DWC3_EP_DELAYED_STOP is set during stop active transfers, then do not
continue attempting to unmap request buffers during dwc3_remove_requests().
This can lead to SMMU faults, as the controller has not stopped the
processing of the TRB. Defer this sequence to the EP0 out start, which
ensures that there are no pending SETUP transactions before issuing the
endxfer.
Reviewed-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Signed-off-by: Wesley Cheng <quic_wcheng@quicinc.com>
Link: https://lore.kernel.org/r/20220901193625.8727-2-quic_wcheng@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Smatch reports the following error: uninitialized symbol 'rlen'
drivers/usb/misc/uss720.c:514 parport_uss720_epp_write_data() error
drivers/usb/misc/uss720.c:575 parport_uss720_ecp_write_data() error
drivers/usb/misc/uss720.c:593 parport_uss720_ecp_read_data() error
drivers/usb/misc/uss720.c:626 parport_uss720_write_compat() error
The root cause is, the failure of usb_bulk_msg leads to the
uninitialized variable rlen in printk function.
Fix this by initializing rlen with zero.
Signed-off-by: Dongliang Mu <mudongliangabcd@gmail.com>
Link: https://lore.kernel.org/r/20220903100004.2874741-1-dzm91@hust.edu.cn
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This from static analysis. The vla_item() takes a size and adds it to
the total. It has a built in integer overflow check so if it encounters
an integer overflow anywhere then it records the total as SIZE_MAX.
However there is an issue here because the "lang_count*(needed_count+1)"
multiplication can overflow. Technically the "lang_count + 1" addition
could overflow too, but that would be detected and is harmless. Fix
both using the new size_add() and size_mul() functions.
Fixes: e6f3862fa1 ("usb: gadget: FunctionFS: Remove VLAIS usage from gadget code")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://lore.kernel.org/r/YxDI3lMYomE7WCjn@kili
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Drop another couple of pointless pr_info() calls, and drop a number of
instances of hcd_name variables that are no longer referenced now that
they are no longer printed to the log at driver registration time.
Fixes: 10174220f5 ("usb: reduce kernel log spam on driver registration")
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Link: https://lore.kernel.org/r/20220905111740.352348-1-ardb@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
I would like to stop exporting OF-specific gpiod_get_from_of_node()
so that gpiolib can be cleaned a bit, so let's switch to the generic
fwnode property API.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Link: https://lore.kernel.org/r/20220903-gpiod_get_from_of_node-remove-v1-5-b29adfb27a6c@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
I would like to stop exporting OF-specific devm_gpiod_get_from_of_node()
so that gpiolib can be cleaned a bit, so let's switch to the generic
device property API.
I believe that the only reason the driver, instead of the standard
devm_gpiod_get(), used devm_gpiod_get_from_of_node() is because it
wanted to set up a pretty consumer name for the GPIO, and we now have
a special API for that.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Link: https://lore.kernel.org/r/20220903-gpiod_get_from_of_node-remove-v1-4-b29adfb27a6c@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The ohci retaining bogus hardware states cause usb disconnect devices
connected before hibernation(s4), this issue occur when ohci-platform
driver build as a module and the built-in ohci-platform driver will
re probe and re enumerate the devices, so there will be no such problem.
Avoid retaining bogus hardware states during resume-from-hibernation.
Previously we had reset the hardware as part of preparing to reinstate
the snapshot image. But we can do better now with the new PM framework,
since we know exactly which resume operations are from hibernation.
According to the commit 'cd1965db054e ("USB: ohci: move ohci_pci_{
suspend,resume} to ohci-hcd.c")' and commit '6ec4beb5c701 ("USB: new
flag for resume-from-hibernation")', the flag "hibernated" is for
resume-from-hibernation and it should be true when usb resume from disk.
When this flag "hibernated" is set, the drivers will reset the hardware
to get rid of any existing state and make sure resume from hibernation
re-enumerates everything for ohci.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Yinbo Zhu <zhuyinbo@loongson.cn>
Link: https://lore.kernel.org/r/20220902063639.17875-1-zhuyinbo@loongson.cn
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We need the USB fixes in here and this resolves the merge issue in:
drivers/usb/dwc3/gadget.c
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 8cb339f1c1 as it
throws up a bunch of sparse warnings as reported by the kernel test
robot.
Reported-by: kernel test robot <lkp@intel.com>
Link: https://lore.kernel.org/r/202209020044.CX2PfZzM-lkp@intel.com
Fixes: 8cb339f1c1 ("usb: gadget: udc-xilinx: replace memcpy with memcpy_toio")
Cc: stable@vger.kernel.org
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Piyush Mehta <piyush.mehta@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since the HC driver is now passed to the function with its
own parameter (it used to be picked from id->driver_data),
the id parameter serves no purpose.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20220831125052.71584-1-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This driver for the PPC Freescale SoC is using device tree
accessors and imperative GPIO semantics control using the old
GPIO API, switch it over to use GPIO descriptors.
Cc: Li Yang <leoyang.li@nxp.com>
Cc: linuxppc-dev@lists.ozlabs.org
Cc: Zhao Qiang <qiang.zhao@freescale.com>
Cc: Guilherme Maciel Ferreira <guilherme.maciel.ferreira@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20220831082932.488724-1-linus.walleij@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
USB external storage device(0x0b05:1932), use gnome-disk-utility tools
to test usb write < 30MB/s.
if does not to load module of uas for this device, can increase the
write speed from 20MB/s to >40MB/s.
Suggested-by: Matthias Kaehlcke <mka@chromium.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Hu Xiaoying <huxiaoying@kylinos.cn>
Link: https://lore.kernel.org/r/20220901045737.3438046-1-huxiaoying@kylinos.cn
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here are a couple of fixes for two long-standing issues with some older
ch341 devices and a number of new device ids.
All have been in linux-next with no reported issues.
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQQHbPq+cpGvN/peuzMLxc3C7H1lCAUCYxB1GAAKCRALxc3C7H1l
CHefAQCxSTeNfnnRHFC/pHlUFa+4U5tVc8zFnwMcnGcZN79dqAEAkjqdLpH8N3tu
baNUP/l1OH86CL4/Rog/hpbBGzJijQg=
=X+Na
-----END PGP SIGNATURE-----
Merge tag 'usb-serial-6.0-rc4' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-linus
Johan writes:
"USB-serial fixes for 6.0-rc4
Here are a couple of fixes for two long-standing issues with some older
ch341 devices and a number of new device ids.
All have been in linux-next with no reported issues."
* tag 'usb-serial-6.0-rc4' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial:
USB: serial: ch341: fix disabled rx timer on older devices
USB: serial: ch341: fix lost character on LCR updates
USB: serial: cp210x: add Decagon UCA device id
USB: serial: option: add support for Cinterion MV32-WA/WB RmNet mode
USB: serial: ftdi_sio: add Omron CS1W-CIF31 device id
USB: serial: option: add Quectel EM060K modem
USB: serial: option: add support for OPPO R11 diag port
At least one older CH341 appears to have the RX timer enable bit
inverted so that setting it disables the RX timer and prevents the FIFO
from emptying until it is full.
Only set the RX timer enable bit for devices with version newer than
0x27 (even though this probably affects all pre-0x30 devices).
Reported-by: Jonathan Woithe <jwoithe@just42.net>
Tested-by: Jonathan Woithe <jwoithe@just42.net>
Link: https://lore.kernel.org/r/Ys1iPTfiZRWj2gXs@marvin.atrad.com.au
Fixes: 4e46c410e0 ("USB: serial: ch341: reinitialize chip on reconfiguration")
Cc: stable@vger.kernel.org # 4.10
Signed-off-by: Johan Hovold <johan@kernel.org>
Disable LCR updates for pre-0x30 devices which use a different (unknown)
protocol for line control and where the current register write causes
the next received character to be lost.
Note that updating LCR using the INIT command has no effect on these
devices either.
Reported-by: Jonathan Woithe <jwoithe@just42.net>
Tested-by: Jonathan Woithe <jwoithe@just42.net>
Link: https://lore.kernel.org/r/Ys1iPTfiZRWj2gXs@marvin.atrad.com.au
Fixes: 4e46c410e0 ("USB: serial: ch341: reinitialize chip on reconfiguration")
Fixes: 55fa15b598 ("USB: serial: ch341: fix baud rate and line-control handling")
Cc: stable@vger.kernel.org # 4.10
Signed-off-by: Johan Hovold <johan@kernel.org>
This reverts commit 3d5f70949f.
The quirk does not work properly, more work is needed to determine what
should be done here.
Reported-by: Oliver Neukum <oneukum@suse.com>
Cc: Jean-Francois Le Fillatre <jflf_kernel@gmx.com>
Cc: stable <stable@kernel.org>
Fixes: 3d5f70949f ("usb: add quirks for Lenovo OneLink+ Dock")
Link: https://lore.kernel.org/r/9a17ea86-079f-510d-e919-01bc53a6d09f@gmx.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Drivers are typically supposed to be quiet unless they are actually
probed, but for some reason, USB host controllers seem to be exempt from
this rule, and happily broadcast their existence into the kernel log at
boot even if the hardware in question is nowhere to be found.
Let's fix that, and remove these pr_info() calls.
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Nicolas Ferre <nicolas.ferre@microchip.com>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: Claudiu Beznea <claudiu.beznea@microchip.com>
Cc: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Cc: Alim Akhtar <alim.akhtar@samsung.com>
Cc: Avi Fishman <avifishman70@gmail.com>
Cc: Tomer Maimon <tmaimon77@gmail.com>
Cc: Tali Perry <tali.perry1@gmail.com>
Cc: Patrick Venture <venture@google.com>
Cc: Nancy Yuen <yuenn@google.com>
Cc: Benjamin Fair <benjaminfair@google.com>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Vladimir Zapolskiy <vz@mleia.com>
Cc: linux-usb@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Cc: linux-samsung-soc@vger.kernel.org
Cc: linux-omap@vger.kernel.org
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Link: https://lore.kernel.org/r/20220825170327.674446-1-ardb@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
USBIP driver packs URB transfer flags in network packets that are
exchanged between Server (usbip_host) and Client (vhci_hcd).
URB_* flags are internal to kernel and could change. Where as USBIP
URB flags exchanged in network packets are USBIP user API must not
change.
Add USBIP_URB* flags to make this an explicit API and change the
client and server to map them. Details as follows:
Client tx path (USBIP_CMD_SUBMIT):
- Maps URB_* to USBIP_URB_* when it sends USBIP_CMD_SUBMIT packet.
Server rx path (USBIP_CMD_SUBMIT):
- Maps USBIP_URB_* to URB_* when it receives USBIP_CMD_SUBMIT packet.
Flags aren't included in USBIP_CMD_UNLINK and USBIP_RET_SUBMIT packets
and no special handling is needed for them in the following cases:
- Server rx path (USBIP_CMD_UNLINK)
- Client rx path & Server tx path (USBIP_RET_SUBMIT)
Update protocol documentation to reflect the change.
Suggested-by: Hongren Zenithal Zheng <i@zenithal.me>
Suggested-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Link: https://lore.kernel.org/r/20220824002456.94605-1-skhan@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
During soft disconnect, EP0 events are expected to be handled in order to
allow the controller to successfully move into the halted state. Since
__dwc3_gadget_stop() is executed before polling, EP0 has been disabled, and
events are being blocked. Allow xfercomplete events to be handled, so that
cached SETUP packets can be read out from the internal controller memory.
Without doing so, it will lead to endxfer timeouts, which results to
controller halt failures.
Reviewed-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Signed-off-by: Wesley Cheng <quic_wcheng@quicinc.com>
Link: https://lore.kernel.org/r/20220817182359.13550-5-quic_wcheng@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Ensure that there are no pending events being handled in between soft
connect/disconnect transitions. As we are keeping interrupts enabled,
and EP0 events are still being serviced, this avoids any stale events from
being serviced.
Reviewed-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Signed-off-by: Wesley Cheng <quic_wcheng@quicinc.com>
Link: https://lore.kernel.org/r/20220817182359.13550-4-quic_wcheng@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If any function drivers request for a delayed status phase, this leads to a
SETUP transfer timeout error, since the function may take longer to process
the DATA stage. This eventually results in end transfer timeouts, as there
is a pending SETUP transaction.
In addition, allow the DWC3_EP_DELAY_STOP to be set for if there is a
delayed status requested. Ocasionally, a host may abort the current SETUP
transaction, by issuing a subsequent SETUP token. In those situations, it
would result in an endxfer timeout as well.
Reviewed-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Signed-off-by: Wesley Cheng <quic_wcheng@quicinc.com>
Link: https://lore.kernel.org/r/20220817182359.13550-3-quic_wcheng@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are some operations that need to be ignored if there is a soft
disconnect in progress. This is to avoid having a pending EP0 transfer in
progress while attempting to stop active transfers and halting the
controller.
There were several instances seen where a soft disconnect was able to occur
during early link negotiation, i.e. bus reset/conndone, which leads to the
conndone handler re-configuring EPs while attempting to halt the
controller, as DEP flags are cleared as part of the soft disconnect path.
ep0out: cmd 'Start New Configuration'
ep0out: cmd 'Set Endpoint Transfer Resource'
ep0in: cmd 'Set Endpoint Transfer Resource'
ep1out: cmd 'Set Endpoint Transfer Resource'
...
event (00030601): Suspend [U3]
event (00000101): Reset [U0]
ep0out: req ffffff87e5c9e100 length 0/0 zsI ==> 0
event (00000201): Connection Done [U0]
ep0out: cmd 'Start New Configuration'
ep0out: cmd 'Set Endpoint Transfer Resource'
In addition, if a soft disconnect occurs, EP0 events are still allowed to
process, however, it will stall/restart during the SETUP phase. The
host is still able to query for the DATA phase, leading to a
xfernotready(DATA) event. Since none of the SETUP transfer parameters are
populated, the xfernotready is treated as a "wrong direction" error,
leading to a duplicate stall/restart routine.
Add the proper softconnect/connected checks in sequences that are
potentially involved during soft disconnect processing.
Reviewed-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Signed-off-by: Wesley Cheng <quic_wcheng@quicinc.com>
Link: https://lore.kernel.org/r/20220817182359.13550-2-quic_wcheng@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The xhci_plat_brcm xhci block can enter suspend with clock disabled to save
power and re-enable them on resume. Make use of the XHCI_SUSPEND_RESUME_CLKS
quirk to do so.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Justin Chen <justinpopo6@gmail.com>
Link: https://lore.kernel.org/r/1660170455-15781-3-git-send-email-justinpopo6@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Introduce XHCI_SUSPEND_RESUME_CLKS quirk as a means to suspend and resume
clocks if the hardware is capable of doing so. We assume that clocks will
be needed if the device may wake.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Justin Chen <justinpopo6@gmail.com>
Link: https://lore.kernel.org/r/1660170455-15781-2-git-send-email-justinpopo6@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently we look up for endpoint in a table and initate urb endpoint
with it. This is unnecessary because the lookup will always result in
endpoint 0.
Suggested-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Khalid Masum <khalid.masum.92@gmail.com>
Link: https://lore.kernel.org/r/20220824203107.14908-1-khalid.masum.92@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
usb_maxpacket() looks up the endpoint number in the pipe which can fail
if the interface or configuration changes before the routine is called.
This is unexpected and may even cause a modulo by zero afterwards.
So use usb_endpoint_maxp() routine which uses the endpoint stored in URB
to get the maxpacket.
Suggested-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Khalid Masum <khalid.masum.92@gmail.com>
Addresses-Coverity: 744857 ("Division or modulo by zero")
Addresses-Coverity: 1487371 ("Division or modulo by zero")
Link: https://lore.kernel.org/r/20220824193813.13129-1-khalid.masum.92@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As follows from #define NAME_TEMPLATE, the procfs code in the RNDIS driver
expects the # of instances to be 3-digit decimal, while the driver calls
ida_simple_get() passing 0 as the 'end' argument which results in actual
max instance # of INT_MAX. Limit the maximum # of RNDIS instances to 1000
which is still a lot! :-)
Found by Linux Verification Center (linuxtesting.org) with the SVACE static
analysis tool.
Signed-off-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Link: https://lore.kernel.org/r/a8180973-3ded-3644-585a-169589a37642@omp.ru
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some platforms make use of VBUS control over PHY which means controller
driver has to access PHY registers to turn on/off VBUS line.This patch
adds support for such platforms in chipidea.
Flag 'CI_HDRC_PHY_VBUS_CONTROL' added to support VBus control feature.
Acked-by: Peter Chen <peter.chen@kernel.org>
Signed-off-by: Piyush Mehta <piyush.mehta@xilinx.com>
Signed-off-by: Piyush Mehta <piyush.mehta@amd.com>
Link: https://lore.kernel.org/r/20220822054051.2941282-1-piyush.mehta@amd.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
these are only used in one place, a few lines lower
Cc: Brooke Basile <brookebasile@gmail.com>
Cc: "Bryan O'Donoghue" <bryan.odonoghue@linaro.org>
Cc: Felipe Balbi <balbi@kernel.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Lorenzo Colitti <lorenzo@google.com>
Signed-off-by: Maciej Żenczykowski <maze@google.com>
Link: https://lore.kernel.org/r/20220821145745.122587-1-zenczykowski@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ISO OUT endpoint is enabled during queuing first usb request
in transfer ring and disabled when TRBERR is reported by controller.
After TRBERR and before next transfer added to TR driver must again
reenable endpoint but does not.
To solve this issue during processing TRBERR event driver must
set the flag EP_UPDATE_EP_TRBADDR in priv_ep->flags field.
Fixes: 7733f6c32e ("usb: cdns3: Add Cadence USB3 DRD Driver")
cc: <stable@vger.kernel.org>
Acked-by: Peter Chen <peter.chen@kernel.org>
Signed-off-by: Pawel Laszczak <pawell@cadence.com>
Link: https://lore.kernel.org/r/20220825062137.5766-1-pawell@cadence.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The TRB_SMM flag indicates that DMA has completed the TD service with
this TRB. Usually it’s a last TRB in TD. In case of ISOC transfer for
bInterval > 1 each ISOC transfer contains more than one TD associated
with usb request (one TD per ITP). In such case the TRB_SMM flag will
be set in every TD and driver will recognize the end of transfer after
processing the first TD with TRB_SMM. In result driver stops updating
request->actual and returns incorrect actual length.
To fix this issue driver additionally must check TRB_CHAIN which is not
used for isochronous transfers.
Fixes: 249f0a25e8 ("usb: cdns3: gadget: handle sg list use case at completion correctly")
cc: <stable@vger.kernel.org>
Acked-by: Peter Chen <peter.chen@kernel.org>
Signed-off-by: Pawel Laszczak <pawell@cadence.com>
Link: https://lore.kernel.org/r/20220825062207.5824-1-pawell@cadence.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
During cdrom emulation, the response to read_toc command must contain
the cdrom address as the number of sectors (2048 byte sized blocks)
represented either as an absolute value (when MSF bit is '0') or in
terms of PMin/PSec/PFrame (when MSF bit is set to '1'). Incase of
cdrom, the fsg_lun_open call sets the sector size to 2048 bytes.
When MAC OS sends a read_toc request with MSF set to '1', the
store_cdrom_address assumes that the address being provided is the
LUN size represented in 512 byte sized blocks instead of 2048. It
tries to modify the address further to convert it to 2048 byte sized
blocks and store it in MSF format. This results in data transfer
failures as the cdrom address being provided in the read_toc response
is incorrect.
Fixes: 3f565a363c ("usb: gadget: storage: adapt logic block size to bound block devices")
Cc: stable@vger.kernel.org
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Krishna Kurapati <quic_kriskura@quicinc.com>
Link: https://lore.kernel.org/r/1661570110-19127-1-git-send-email-quic_kriskura@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Automatic kernel fuzzing revealed a recursive locking violation in
usb-storage:
============================================
WARNING: possible recursive locking detected
5.18.0 #3 Not tainted
--------------------------------------------
kworker/1:3/1205 is trying to acquire lock:
ffff888018638db8 (&us_interface_key[i]){+.+.}-{3:3}, at:
usb_stor_pre_reset+0x35/0x40 drivers/usb/storage/usb.c:230
but task is already holding lock:
ffff888018638db8 (&us_interface_key[i]){+.+.}-{3:3}, at:
usb_stor_pre_reset+0x35/0x40 drivers/usb/storage/usb.c:230
...
stack backtrace:
CPU: 1 PID: 1205 Comm: kworker/1:3 Not tainted 5.18.0 #3
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS
1.13.0-1ubuntu1.1 04/01/2014
Workqueue: usb_hub_wq hub_event
Call Trace:
<TASK>
__dump_stack lib/dump_stack.c:88 [inline]
dump_stack_lvl+0xcd/0x134 lib/dump_stack.c:106
print_deadlock_bug kernel/locking/lockdep.c:2988 [inline]
check_deadlock kernel/locking/lockdep.c:3031 [inline]
validate_chain kernel/locking/lockdep.c:3816 [inline]
__lock_acquire.cold+0x152/0x3ca kernel/locking/lockdep.c:5053
lock_acquire kernel/locking/lockdep.c:5665 [inline]
lock_acquire+0x1ab/0x520 kernel/locking/lockdep.c:5630
__mutex_lock_common kernel/locking/mutex.c:603 [inline]
__mutex_lock+0x14f/0x1610 kernel/locking/mutex.c:747
usb_stor_pre_reset+0x35/0x40 drivers/usb/storage/usb.c:230
usb_reset_device+0x37d/0x9a0 drivers/usb/core/hub.c:6109
r871xu_dev_remove+0x21a/0x270 drivers/staging/rtl8712/usb_intf.c:622
usb_unbind_interface+0x1bd/0x890 drivers/usb/core/driver.c:458
device_remove drivers/base/dd.c:545 [inline]
device_remove+0x11f/0x170 drivers/base/dd.c:537
__device_release_driver drivers/base/dd.c:1222 [inline]
device_release_driver_internal+0x1a7/0x2f0 drivers/base/dd.c:1248
usb_driver_release_interface+0x102/0x180 drivers/usb/core/driver.c:627
usb_forced_unbind_intf+0x4d/0xa0 drivers/usb/core/driver.c:1118
usb_reset_device+0x39b/0x9a0 drivers/usb/core/hub.c:6114
This turned out not to be an error in usb-storage but rather a nested
device reset attempt. That is, as the rtl8712 driver was being
unbound from a composite device in preparation for an unrelated USB
reset (that driver does not have pre_reset or post_reset callbacks),
its ->remove routine called usb_reset_device() -- thus nesting one
reset call within another.
Performing a reset as part of disconnect processing is a questionable
practice at best. However, the bug report points out that the USB
core does not have any protection against nested resets. Adding a
reset_in_progress flag and testing it will prevent such errors in the
future.
Link: https://lore.kernel.org/all/CAB7eexKUpvX-JNiLzhXBDWgfg2T9e9_0Tw4HQ6keN==voRbP0g@mail.gmail.com/
Cc: stable@vger.kernel.org
Reported-and-tested-by: Rondreis <linhaoguo86@gmail.com>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/YwkflDxvg0KWqyZK@rowland.harvard.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A recent commit expanding the scope of the udc_lock mutex in the
gadget core managed to cause an obscure and slightly bizarre lockdep
violation. In abbreviated form:
======================================================
WARNING: possible circular locking dependency detected
5.19.0-rc7+ #12510 Not tainted
------------------------------------------------------
udevadm/312 is trying to acquire lock:
ffff80000aae1058 (udc_lock){+.+.}-{3:3}, at: usb_udc_uevent+0x54/0xe0
but task is already holding lock:
ffff000002277548 (kn->active#4){++++}-{0:0}, at: kernfs_seq_start+0x34/0xe0
which lock already depends on the new lock.
the existing dependency chain (in reverse order) is:
-> #3 (kn->active#4){++++}-{0:0}:
lock_acquire+0x68/0x84
__kernfs_remove+0x268/0x380
kernfs_remove_by_name_ns+0x58/0xac
sysfs_remove_file_ns+0x18/0x24
device_del+0x15c/0x440
-> #2 (device_links_lock){+.+.}-{3:3}:
lock_acquire+0x68/0x84
__mutex_lock+0x9c/0x430
mutex_lock_nested+0x38/0x64
device_link_remove+0x3c/0xa0
_regulator_put.part.0+0x168/0x190
regulator_put+0x3c/0x54
devm_regulator_release+0x14/0x20
-> #1 (regulator_list_mutex){+.+.}-{3:3}:
lock_acquire+0x68/0x84
__mutex_lock+0x9c/0x430
mutex_lock_nested+0x38/0x64
regulator_lock_dependent+0x54/0x284
regulator_enable+0x34/0x80
phy_power_on+0x24/0x130
__dwc2_lowlevel_hw_enable+0x100/0x130
dwc2_lowlevel_hw_enable+0x18/0x40
dwc2_hsotg_udc_start+0x6c/0x2f0
gadget_bind_driver+0x124/0x1f4
-> #0 (udc_lock){+.+.}-{3:3}:
__lock_acquire+0x1298/0x20cc
lock_acquire.part.0+0xe0/0x230
lock_acquire+0x68/0x84
__mutex_lock+0x9c/0x430
mutex_lock_nested+0x38/0x64
usb_udc_uevent+0x54/0xe0
Evidently this was caused by the scope of udc_mutex being too large.
The mutex is only meant to protect udc->driver along with a few other
things. As far as I can tell, there's no reason for the mutex to be
held while the gadget core calls a gadget driver's ->bind or ->unbind
routine, or while a UDC is being started or stopped. (This accounts
for link #1 in the chain above, where the mutex is held while the
dwc2_hsotg_udc is started as part of driver probing.)
Gadget drivers' ->disconnect callbacks are problematic. Even though
usb_gadget_disconnect() will now acquire the udc_mutex, there's a
window in usb_gadget_bind_driver() between the times when the mutex is
released and the ->bind callback is invoked. If a disconnect occurred
during that window, we could call the driver's ->disconnect routine
before its ->bind routine. To prevent this from happening, it will be
necessary to prevent a UDC from connecting while it has no gadget
driver. This should be done already but it doesn't seem to be;
currently usb_gadget_connect() has no check for this. Such a check
will have to be added later.
Some degree of mutual exclusion is required in soft_connect_store(),
which can dereference udc->driver at arbitrary times since it is a
sysfs callback. The solution here is to acquire the gadget's device
lock rather than the udc_mutex. Since the driver core guarantees that
the device lock is always held during driver binding and unbinding,
this will make the accesses in soft_connect_store() mutually exclusive
with any changes to udc->driver.
Lastly, it turns out there is one place which should hold the
udc_mutex but currently does not: The function_show() routine needs
protection while it dereferences udc->driver. The missing lock and
unlock calls are added.
Link: https://lore.kernel.org/all/b2ba4245-9917-e399-94c8-03a383e7070e@samsung.com/
Fixes: 2191c00855 ("USB: gadget: Fix use-after-free Read in usb_udc_uevent()")
Cc: Felipe Balbi <balbi@kernel.org>
Cc: stable@vger.kernel.org
Reported-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/YwkfhdxA/I2nOcK7@rowland.harvard.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since 1599069a62 ("phy: core: Warn when phy_power_on is called before
phy_init") the driver complains. In my case (Amlogic SoC) the warning
is: phy phy-fe03e000.phy.2: phy_power_on was called before phy_init
So change the order of the two calls. The same change has to be done
to the order of phy_exit() and phy_power_off().
Fixes: 09a75e8577 ("usb: dwc2: refactor common low-level hw code to platform.c")
Cc: stable@vger.kernel.org
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Acked-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://lore.kernel.org/r/dfcc6b40-2274-4e86-e73c-5c5e6aa3e046@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Retimer device class is left dangling when the typec module
is unloaded. Attempts to reload the module failed with warning:
"sysfs: cannot create duplicate filename '/class/retimer'"
Fixing the issue by unregistering the class properly.
Fixes: ddaf8d96f9 ("usb: typec: Add support for retimers")
Reviewed-by: Prashant Malani <pmalani@chromium.org>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20220825140411.10743-1-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The dwc3 driver manages its PHYs itself so the USB core PHY management
needs to be disabled.
Use the struct xhci_plat_priv hack added by commits 46034a999c ("usb:
host: xhci-plat: add platform data support") and f768e71891 ("usb:
host: xhci-plat: add priv quirk for skip PHY initialization") to
propagate the setting for now.
Fixes: 4e88d4c083 ("usb: add a flag to skip PHY initialization to struct usb_hcd")
Fixes: 178a0bce05 ("usb: core: hcd: integrate the PHY wrapper into the HCD core")
Tested-by: Matthias Kaehlcke <mka@chromium.org>
Cc: stable <stable@kernel.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20220825131836.19769-1-johan+linaro@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
