This patch fixes bug on gpio drive strength helper function.
The offset should be like follwoing.
- off = chip->chip.base - pin;
+ off = pin - chip->chip.base;
In the s5p_gpio_get_drvstr(),
the second line is unnecessary, because overwrite drvstr.
drvstr = __raw_readl(reg);
- drvstr = 0xffff & (0x3 << shift);
And need 2bit masking before return the drvstr value.
drvstr = drvstr >> shift;
+ drvstr &= 0x3;
In the s5p_gpio_set_drvstr(), need relevant bit clear.
tmp = __raw_readl(reg);
+ tmp &= ~(0x3 << shift);
tmp |= drvstr << shift;
Reported-by: Jaecheol Lee <jc.lee@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch fixes on defined drive strength value for GPIO.
According to data sheet, if we want drive strength 1x, the value
should be 00(b), if 2x should be 10(b), if 3x should be 01(b),
and if 4x should be 11(b). Also fixes comment(from S5C to S5P).
Reported-by: Janghyuck Kim <janghyuck.kim@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
These clocks enables FIMC driver to operate on machines, which
bootloader power gated FIMC devices to save power on boot.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
[kgene.kim@samsung.com: minor title fix]
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
My macbook infrared remote control was broken by commit
bd25f4dd69 ("HID: hiddev: use
usb_find_interface, get rid of BKL").
This device appears in dmesg as:
apple 0003:05AC:8242.0001: hiddev0,hidraw0: USB HID v1.11 Device
[Apple Computer, Inc. IR Receiver] on usb-0000:00:1d.2-1/input0
It stopped working as lircd was getting ENODEV when opening /dev/usb/hiddev0.
AFAICS hiddev_driver is a dummy driver so usb_find_interface(&hiddev_driver)
does not find anything.
The device is associated with the usbhid driver, so let's do
usb_find_interface(&hid_driver) instead.
$ ls -l /sys/devices/pci0000:00/0000:00:1d.2/usb7/7-1/7-1:1.0/usb/hiddev0/device/driver
lrwxrwxrwx 1 root root 0 2010-09-12 16:28 /sys/devices/pci0000:00/0000:00:1d.2/usb7/7-1/7-1:1.0/usb/hiddev0/device/driver -> ../../../../../../bus/usb/drivers/usbhid
Signed-off-by: Guillaume Chazarain <guichaz@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
CLK_GATE_IP3[8] is RESERVED. The port "I2C_HDMI_DDC" of CLK_GATE_IP3[10] is
used as another I2C port. Therefore, defined the unused I2C-1 as another I2C
there was left undefined but used.
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
IO registers region size of all FIMC versions is less than 1kB so there
is no need to reserve 1M.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
[kgene.kim@samsung.com: minor title fix]
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
FIMC driver uses DMA_coherent allocator, which requires proper dma mask
to be set.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
[kgene.kim@samsung.com: minor title fix]
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
We must ensure that ide_proc_port_register_devices() occurs on an
interface before ide_proc_register_driver() executes for that
interfaces drives.
Therefore defer the registry of the driver device objects backed by
ide_bus_type until after ide_proc_port_register_devices() has run
and thus all of the drive->proc procfs directory pointers have been
setup.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
While integrating your man-pages patch for IP_NODEFRAG, I noticed
that this option is settable by setsockopt(), but not gettable by
getsockopt(). I suppose this is not intended. The (untested,
trivial) patch below adds getsockopt() support.
Signed-off-by: Michael kerrisk <mtk.manpages@gmail.com>
Acked-by: Jiri Olsa <jolsa@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The arch/x86/Makefile uses scripts/gcc-x86_$(BITS)-has-stack-protector.sh
to check if cc1 supports -fstack-protector. When -fPIE is passed to cc1,
these scripts fail causing stack protection to be disabled even when it
is available.
This fix is similar to commit c47efe5548
Reported-by: Kai Dietrich <mail@cleeus.de>
Signed-off-by: Magnus Granberg <zorry@gentoo.org>
LKML-Reference: <20100913101319.748A1148E216@opensource.dyc.edu>
Signed-off-by: Anthony G. Basile <basile@opensource.dyc.edu>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Gcc 3.x generates a warning
arch/x86/include/asm/cpufeature.h: In function `__static_cpu_has':
arch/x86/include/asm/cpufeature.h:326: warning: asm operand 1 probably doesn't match constraints
on each file.
But static_cpu_has() for gcc 3.x does not need __static_cpu_has().
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
LKML-Reference: <201008300127.o7U1RC6Z044051@www262.sakura.ne.jp>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
* 'sched/urgent' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
sched: Improve latencies under load by decreasing minimum scheduling granularity
After all these years, it turns out that the
/proc/sys/net/ipv4/conf/*/force_igmp_version
parameter isn't fully implemented.
*Symptom*:
When set force_igmp_version to a value of 2, the kernel should only perform
multicast IGMPv2 operations (IETF rfc2236). An host-initiated Join message
will be sent as a IGMPv2 Join message. But if a IGMPv3 query message is
received, the host responds with a IGMPv3 join message. Per rfc3376 and
rfc2236, a IGMPv2 host should treat a IGMPv3 query as a IGMPv2 query and
respond with an IGMPv2 Join message.
*Consequences*:
This is an issue when a IGMPv3 capable switch is the querier and will only
issue IGMPv3 queries (which double as IGMPv2 querys) and there's an
intermediate switch that is only IGMPv2 capable. The intermediate switch
processes the initial v2 Join, but fails to recognize the IGMPv3 Join responses
to the Query, resulting in a dropped connection when the intermediate v2-only
switch times it out.
*Identifying issue in the kernel source*:
The issue is in this section of code (in net/ipv4/igmp.c), which is called when
an IGMP query is received (from mainline 2.6.36-rc3 gitweb):
...
A IGMPv3 query has a length >= 12 and no sources. This routine will exit after
line 880, setting the general query timer (random timeout between 0 and query
response time). This calls igmp_gq_timer_expire():
...
.. which only sends a v3 response. So if a v3 query is received, the kernel
always sends a v3 response.
IGMP queries happen once every 60 sec (per vlan), so the traffic is low. A
IGMPv3 query *is* a strict superset of a IGMPv2 query, so this patch properly
short circuit's the v3 behaviour.
One issue is that this does not address force_igmp_version=1. Then again, I've
never seen any IGMPv1 multicast equipment in the wild. However there is a lot
of v2-only equipment. If it's necessary to support the IGMPv1 case as well:
837 if (len == 8 || IGMP_V2_SEEN(in_dev) || IGMP_V1_SEEN(in_dev)) {
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux-2.6:
[IA64] fix siglock
Quoth Tony:
"I committed the fix for this last week prior to your -rc4 announcement
reminding us to give proper "Reported-by:" credit. This one should have
had:
Reported-by: Tony Ernst <tee@sgi.com>
and also
Much-useful-investigation-and-tracing-by: Hedi Berriche <hedi@sgi.com>
Much-useful-investigation-and-tracing-by: Petr Tesarik <ptesarik@novell.com>"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ericvh/v9fs:
fs/9p: Don't use dotl version of mknod for dotu inode operations
fs/9p: Use the correct dentry operations
9p: Check for NULL fid in v9fs_dir_release()
fs/9p: Fix error handling in v9fs_get_sb
fs/9p, net/9p: memory leak fixes
* 'next-spi' of git://git.secretlab.ca/git/linux-2.6:
spi/pl022: move probe call to subsys_initcall()
powerpc/5200: mpc52xx_uart.c: Add of_node_put to avoid memory leak
spi/pl022: fix APB pclk power regression on U300
spi/spi_s3c64xx: Warn if PIO transfers time out
spi/s3c64xx: Fix incorrect reuse of 'val' local variable.
spi/s3c64xx: Fix compilation warning
spi/dw_spi: clean the cs_control code
spi/dw_spi: Allow interrupt sharing
spi/spi_s3c64xx: Increase dead reckoning time in wait_for_xfer()
spi/spi_s3c64xx: Move to subsys_initcall()
spi: free children in spi_unregister_master, not siblings
gpiolib: Add 'struct gpio_chip' forward declaration for !GPIOLIB case
of: Fix missing includes - ll_temac
spi/spi_s3c64xx: Staticise non-exported functions
spi/spi_s3c64xx: Make probe more robust against missing board config
Smatch complains because we check whether "pch->chan" is NULL and then
dereference it unconditionally on the next line. Partly the reason this
bug was introduced is because code was too complicated. I've simplified
it a little.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The members of struct llc_sock are unsigned so if we pass a negative
value for "opt" it can cause a sign bug. Also it can cause an integer
overflow when we multiply "opt * HZ".
CC: stable@kernel.org
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Mathieu reported bad latencies with make -j10 kind of kbuild
workloads - which is mostly caused by us scheduling with a
too coarse granularity.
Reduce the minimum granularity some more, to make sure we
can meet the latency target.
I got the following results (make -j10 kbuild load, average of 3
runs):
vanilla:
maximum latency: 38278.9 µs
average latency: 7730.1 µs
patched:
maximum latency: 22702.1 µs
average latency: 6684.8 µs
Mathieu also measured it:
|
| * wakeup-latency.c (SIGEV_THREAD) with make -j10
|
| - Mainline 2.6.35.2 kernel
|
| maximum latency: 45762.1 µs
| average latency: 7348.6 µs
|
| - With only Peter's smaller min_gran (shown below):
|
| maximum latency: 29100.6 µs
| average latency: 6684.1 µs
|
Reported-by: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Acked-by: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Suggested-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
LKML-Reference: <AANLkTi=8m4g01wZPacySoF7U0PevTNVgJoZZrHiUD-pN@mail.gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
We should not use dotlversion for the dotu inode operations
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Eric Van Hensbergen <ericvh@gmail.com>
We should use the cached dentry operation only if caching mode is enabled
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Eric Van Hensbergen <ericvh@gmail.com>
NULL fid should be handled in cases where we endup calling v9fs_dir_release()
before even we instantiate the fid in filp.
Signed-off-by: Venkateswararao Jujjuri <jvrao@linux.vnet.ibm.com>
Signed-off-by: Eric Van Hensbergen <ericvh@gmail.com>
This was introduced by 7cadb63d58a932041afa3f957d5cbb6ce69dcee5
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Eric Van Hensbergen <ericvh@gmail.com>
Add a quirk for laptop Toshiba Satellite C650D to have proper external HP and
external Mic support.
Signed-off-by: Anisse Astier <anisse@astier.eu>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This commit fixes bogus CS rejection if it contains a sequence
of the following operations:
- Set the color buffer 0. track->cb[i].robj becomes non-NULL.
- Render.
- Set a larger zbuffer than the previously-set color buffer.
- Set a larger scissor area as well.
- Set the color channel mask to 0 to do depth-only rendering.
- Render. --> rejected, because track->cb[i].robj remained non-NULL,
therefore the conditional checking for the color channel mask and
friends is not performed, and the larger scissor area causes
the rejection.
This fixes bugs:
- https://bugs.freedesktop.org/show_bug.cgi?id=29762
- https://bugs.freedesktop.org/show_bug.cgi?id=28869
And maybe some others which seem to look the same.
If possible, this commit should go to stable as well.
Signed-off-by: Marek Olšák <maraeo@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
One subtest of mesa/demos/gltestperf takes 9 seconds to complete,
so to prevent an unnecessary gpu reset followed by a hardlock, I am
increasing the interval to 10 seconds after which a GPU is considered
in a locked-up state. This is on RV530. However, with a little slower GPU,
we would surpass the interval easily, so this is not a good fix
for gltestperf.
Nevertheless, this commit also fixes hardlocks in the applications which
render at speed of less than 1 frame per second, where the whole frame
consists of only one command stream. The game Tiny & Big is an example.
This bar is now lowered to 0.1 fps.
Now the question comes down to whether we should (often unsuccessfully)
reset the GPU at all? Once we have stable enough drivers, we won't have to.
Has the time come already?
If possible, this commit should go to stable as well.
Signed-off-by: Marek Olšák <maraeo@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This patch fixes rendering errors on some evergreen boards.
Hardcoding the backend map is not an optimal solution, but
a better fix is being worked on.
Similar to the fix for rv740
(6271901d82).
Fixes:
https://bugs.freedesktop.org/show_bug.cgi?id=29986
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
Destructive load-detection is very expensive and due to failings
elsewhere can trigger system wide stalls of up to 600ms. A simple
first step to correcting this is not to invoke such an expensive
and destructive load-detection operation automatically.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=29536
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=16265
Reported-by: Bruno Prémont <bonbons@linux-vserver.org>
Tested-by: Sitsofe Wheeler <sitsofe@yahoo.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
Otherwise when disabling the output we switch to the new fb (which is
likely NULL) and skip the call to mode_set -- leaking driver private
state on the old_fb.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=29857
Reported-by: Sitsofe Wheeler <sitsofe@yahoo.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Dave Airlie <airlied@redhat.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
caused by d65d65b175
need to update the radeon crtc priv native mode before using it.
Fixes:
https://bugs.freedesktop.org/show_bug.cgi?id=30049
v2: integrate v/h copy paste typo
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
I broke out my trusty i845 and found a new boot failure, which upon
inspection turned out to be a recursion within:
drm_helper_probe_single_connector_modes() -> drm_helper_hpd_irq_event()
-> intel_crt_detect() -> drm_helper_probe_single_connector_modes()
Calling drm_kms_helper_poll_enable() instead performs the desired
re-initialisation of the polling should the user have toggled the
parameter, without the recursive side-effect.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Dave Airlie <airlied@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Mark F. Brown <mark.brown314@gmail.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This patch initializes the pages per block field in CONFIG1 for
v2 controllers. It also sets the FP_INT field. This is the last
field not correctly initialized, so we can switch from
read/modify/write the CONFIG1 reg to just write the correct
value.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: John Ogness <john.ogness@linutronix.de>
Tested-by: John Ogness <john.ogness@linutronix.de>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
When DMA error occurs. it's loop hang since it can't exit the loop.
and it's the right DMA handling code as Spec.
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Wrong assumption bufferram can be switched between BufferRAM0 and BufferRAM1
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Since info->mtd isn't dynamically allocated, we shouldn't attempt to
kfree() it. Otherwise we get random fun corruption when unloading
the driver built as a module.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Seems some patches got out sync when being merged. The Blackfin NFC
driver was updated to use nand_scan_ident(), but it missed the change
where nand_scan_ident() now takes 3 arguments. So update this driver
to fix build failures.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The NFSv4 client's callback server calls svc_gss_principal(), which
is defined in the auth_rpcgss.ko
The NFSv4 server has the same dependency, and in addition calls
svcauth_gss_flavor(), gss_mech_get_by_pseudoflavor(),
gss_pseudoflavor_to_service() and gss_mech_put() from the same module.
The module auth_rpcgss itself has no dependencies aside from sunrpc,
so we only need to select RPCSEC_GSS.
Reported-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
