Commit Graph

25 Commits

Author SHA1 Message Date
Mark Brown
67e85d4e4e
Merge remote-tracking branches 'asoc/topic/cygnus', 'asoc/topic/da7213', 'asoc/topic/davinci' and 'asoc/topic/doc' into asoc-next 2017-11-10 21:31:10 +00:00
Matthias Reichl
abd4f0e1c2
ASoC: bcm2835: Support left/right justified and DSP modes
DSP modes and left/right justified modes can be supported
on bcm2835 by configuring the frame sync polarity and
frame sync length registers and by adjusting the
channel data position registers.

Clock and frame sync polarity handling in hw_params has
been refactored to make the interaction between logical
rising/falling edge frame start and physical configuration
(changed by normal/inverted polarity modes) clearer.

Modes where the first active data bit is transmitted immediately
after frame start (eg DSP mode B with slot 0 active)
only work reliable if bcm2835 is configured as frame master.
In frame slave mode channel swap (or shift, this isn't quite
clear yet) can occur.

Currently the driver only warns if an unstable configuration
is detected but doensn't prevent using them.

Signed-off-by: Matthias Reichl <hias@horus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
2017-11-10 21:26:07 +00:00
Matthias Reichl
3d2b3c707b
ASoC: bcm2835: Enforce full symmetry
bcm2835's configuration registers can't be changed when a stream
is running, which means asymmetric configurations aren't supported.

Channel and rate symmetry are already enforced by constraints
but samplebits had been missed.

As hw_params doesn't check for symmetry constraints by itself
and just returns success if a stream is running this led to
situations where asymmetric configurations were seeming to
succeed but of course didn't work because the hardware wasn't
configured at all.

Fix this by adding the missing samplerate symmetry constraint.

Signed-off-by: Matthias Reichl <hias@horus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
2017-11-10 21:26:03 +00:00
Matthias Reichl
675c0ee514
ASoC: bcm2835: Support additional samplerates up to 384kHz
Sample rates are only restricted by the capabilities of the
clock driver, so use SNDRV_PCM_RATE_CONTINUOUS instead of
SNDRV_PCM_RATE_8000_192000.

Tests (eg with pcm5122) have shown that bcm2835 works fine
in 384kHz/32bit stereo mode, so change the maximum allowed
rate from 192kHz to 384kHz.

Signed-off-by: Matthias Reichl <hias@horus.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Mark Brown <broonie@kernel.org>
2017-11-10 21:24:34 +00:00
Matthias Reichl
9448572d98
ASoC: bcm2835: Add support for TDM modes
bcm2835 supports arbitrary positioning of channel data within
a frame and thus is capable of supporting TDM modes. Since
the driver is limited to 2-channel operations only TDM setups
with exactly 2 active slots are supported.

Logical TDM slot numbering follows the usual convention:

For I2S-like modes, with a 50% duty-cycle frame clock,
slots 0, 2, ... are transmitted in the first half of a frame,
slots 1, 3, ... are transmitted in the second half.

For DSP modes slot numbering is ascending: 0, 1, 2, 3, ...

Channel position calculation has been refactored to use
TDM info and moved out of hw_params.

set_tdm_slot, set_bclk_ratio and hw_params now check more
strictly if the configuration is valid. Illegal configurations
like odd number of slots in I2S mode, data lengths exceeding
slot width or frame sizes larger than the hardware limit of
1024 are rejected. Also hw_params now properly checks for
errors from clk_set_rate.

Allowed PCM formats are already guarded by stream constraints,
thus the formats check in hw_params has been removed and
data_length is now retrieved via params_width().

Also standard functions like snd_soc_params_to_bclk are now
being used instead of manual calculations to make the code
more readable.

Special care has been taken to ensure that set_bclk_ratio works
as before. The bclk ratio is mapped to a 2-channel TDM config
with a slot width of half the ratio. In order to support odd ratios,
which can't be expressed via a TDM config, the ratio (frame length)
is stored and used by hw_params.

Signed-off-by: Matthias Reichl <hias@horus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
2017-11-10 21:24:30 +00:00
Christos Gkekas
4c75968a1b ASoC: cygnus: Remove unnecessary active_slots check
Variable active_slots is unsigned so checking whether it is less than
zero is not necessary.

Signed-off-by: Christos Gkekas <chris.gekas@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
2017-10-09 09:41:05 +01:00
Lori Hikichi
934e4885cb ASoC: cygnus: Remove support for 8 bit audio and for mono
These modes of operation were not working properly and it is
unclear if the hardware could fully support these modes properly.
There is little to be gained by enabling these modes, therefore,
we will just remove support.

Signed-off-by: Lori Hikichi <lori.hikichi@broadcom.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
2017-10-04 11:59:37 +01:00
Lori Hikichi
fcf30f3b43 ASoC: cygnus: Remove set_fmt from SPDIF dai ops
The SPDIF port cannot modify its format so a set_fmt function is not
needed. Previously, we used a generic set_fmt for all ports and returned
an error code for the SPDIF port. It is cleaner to not populate the
set_fmt field.

Signed-off-by: Lori Hikichi <lori.hikichi@broadcom.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
2017-10-04 11:59:24 +01:00
Lori Hikichi
d8302aa6b5 ASoC: cygnus: Add EXPORT_SYMBOL for helper function
The helper function cygnus_ssp_set_custom_fsync_width() is intended
to be called from an ASoC machine driver, need to export symbol
if using modules.

Signed-off-by: Lori Hikichi <lori.hikichi@broadcom.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
2017-10-04 11:59:16 +01:00
Mark Brown
3b2d0bb5ef Merge remote-tracking branches 'asoc/topic/cs43130', 'asoc/topic/cs53l30', 'asoc/topic/cygnus' and 'asoc/topic/davinci' into asoc-next 2017-09-01 12:12:32 +01:00
Bhumika Goyal
cc6e25631d ASoC: bcm: make snd_soc_dai_driver const
Make this const as it is only used during a copy operation.
Done using Coccinelle.

Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
2017-08-17 18:10:17 +01:00
Lori Hikichi
8937ea0f3c ASoC: cygnus: Add support for 384kHz frame rates
Allow the audio ports to operate at 384kHz.

Signed-off-by: Lori Hikichi <lori.hikichi@broadcom.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
2017-08-15 18:14:40 +01:00
Scott Branden
fe3683779e ASoC: bcm: add depends on HAS_DMA
add depends on HAS_DMA to Kconfig.  This fixes error reported
by kbuild test robot when building for ARCH=m32r:
ERROR: "bad_dma_ops" [sound/soc/bcm/snd-soc-cygnus.ko] undefined!

Signed-off-by: Scott Branden <scott.branden@broadcom.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
2016-11-02 14:57:05 -06:00
Simran Rai
1200a7d9b2 ASoC: cygnus: Add Cygnus audio DMA driver
This patch adds Cygnus audio DMA driver. It supports playback
and capture modes and uses ringbuffers for data transfer.

Signed-off-by: Lori Hikichi <lhikichi@broadcom.com>
Signed-off-by: Simran Rai <ssimran@broadcom.com>
Reviewed-by: Ray Jui <rjui@broadcom.com>
Reviewed-by: Arun Parameswaran <arunp@broadcom.com>
Reviewed-by: Scott Branden <sbranden@broadcom.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
2016-05-31 17:50:42 +01:00
Simran Rai
a6ee05d94e ASoC: cygnus: Add Cygnus audio DAI driver
This patch adds Cygnus audio DAI driver. It supports I2S, TDM
and SPDIF modes and uses three clocks derived from PLL.

This patchset has been tested on Cygnus wireless audio
bcm958305K board.

Signed-off-by: Lori Hikichi <lhikichi@broadcom.com>
Signed-off-by: Simran Rai <ssimran@broadcom.com>
Reviewed-by: Ray Jui <rjui@broadcom.com>
Reviewed-by: Arun Parameswaran <arunp@broadcom.com>
Reviewed-by: Scott Branden <sbranden@broadcom.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
2016-05-31 17:50:42 +01:00
Matthias Reichl
beff053c0e ASoC: bcm2835: Add S16_LE support via packed DMA transfers
The bcm2835-i2s driver already has support for the S16_LE format but
that format hasn't been made available because dmaengine_pcm didn't
support packed data transfers.

bcm2835-i2s needs 16-bit left+right channel data to be packed into
a 32-bit word, the FIFO register is 32-bit only and doesn't support
16-bit access.

Now that dmaengine_pcm supports packed transfers the format can
be made available by setting the SND_DMAENGINE_PCM_DAI_FLAG_PACK flag.

No further configuration is necessary:
- snd_dmaengine_dai_dma_data.addr_width is already set to
  DMA_SLAVE_BUSWIDTH_4_BYTES to force 32-bit DMA transfers
- dmaengine_pcm will pick up the S16_LE format from the DAI
  configuration and make it available since it's no longer
  masked out due to the PACK flag.
- there are no further corner cases to catch in hw_params,
  since the channel count is fixed at 2 we always have two
  16-bit stereo samples that can be transferred via 32-bit DMA

Signed-off-by: Matthias Reichl <hias@horus.com>
Tested-by: Martin Sperl <kernel@martin.sperl.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
2016-04-27 17:35:53 +01:00
Matthias Reichl
60507fe191 ASoC: bcm2835: setup clock only if CPU is clock master
We only need to enable the clock if we are a clock master.

Code ported from bcm2708-i2s driver in Raspberry Pi tree.
Original work by Zoltan Szenczi.

Signed-off-by: Matthias Reichl <hias@horus.com>
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
2016-04-25 17:39:11 +01:00
Matthias Reichl
a34b027dca ASoC: bcm2835: add 24bit support
This adds 24 bit support to the I2S driver of the BCM2835

Code ported from bcm2708-i2s driver in Raspberry Pi tree.

Signed-off-by: Florian Meier <florian.meier@koalo.de>
Signed-off-by: Matthias Reichl <hias@horus.com>
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
2016-04-25 17:39:05 +01:00
Martin Sperl
517e7a1537 ASoC: bcm2835: move to use the clock framework
Since the move to the new clock framework with commit 94cb7f76ca
("ARM: bcm2835: Switch to using the new clock driver support.")
this driver was no longer functional as it was manipulating the
clock registers locally without going true the framework.

This patch moves to use the new clock framework and also
moves away from the hardcoded address offsets for DMA getting
the dma-address directly from the device tree.

Note that the optimal bclk_ratio selection to avoid jitter
due to the use of fractional dividers, which is in the
current version has been removed, because not all devices
support these non power of 2 sized transfers, which resulted
in lots of (downstream) modules that use:
  snd_soc_dai_set_bclk_ratio(cpu_dai, sample_bits * 2);

Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
2016-01-15 18:09:10 +00:00
Martin Sperl
7905f08247 ASoC: bcm2835: cleanup includes by ordering them alphabetically
Cleanup of includes so that they are ordered alphabetically.

Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
2016-01-10 12:44:47 +00:00
Luis de Bethencourt
054bc835d2 ASoC: bcm2835-i2s: Fix module autoload for OF platform drivers
These platform drivers have a OF device ID table but the OF module
alias information is not created so module autoloading won't work.

Signed-off-by: Luis de Bethencourt <luis@debethencourt.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
2015-08-27 20:22:47 +01:00
Wolfram Sang
ea3bccab07 ASoC: bcm: drop owner assignment from platform_drivers
A platform_driver does not need to set an owner, it will be populated by the
driver core.

Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2014-10-20 16:22:04 +02:00
Takashi Iwai
053ad6a057 ASoC: bcm: Remove obsoleted Kconfig dependency
CONFIG_SND_SOC_DMAENGINE_PCM was renamed to CONFIG_SND_DMAENGINE_PCM
recently.  And yet we don't have to select it since
CONFIG_SND_GENERIC_DMAENGINE_PCM selects the dependency by itself, so
just rip it off.

Signed-off-by: Takashi Iwai <tiwai@suse.de>
Acked-by: Florian Meier <florian.meier@koalo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
2014-01-08 20:00:04 +00:00
Lars-Peter Clausen
3990c516de ASoC: bcm2835-i2s: Use devm_snd_dmaengine_pcm_register()
Makes the code slightly shorter.

Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
2013-12-02 11:47:16 +00:00
Florian Meier
c6aeb7de22 ASoC: Add support for BCM2835
This driver adds support for digital audio (I2S)
for the BCM2835 SoC that is used by the
Raspberry Pi. External audio codecs can be
connected to the Raspberry Pi via P5 header.

It relies on cyclic DMA engine support for BCM2835.

Signed-off-by: Florian Meier <florian.meier@koalo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
2013-11-25 17:17:08 +00:00