Provide MAC time, rate, channel, signal and noise.
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Don't try to skip any headers in hostap_80211_header_parse(). We never
use that function for interfaces affected by local->monitor_type. Both
the master and the AP interface receive 802.11 frames without any
additional headers.
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes the rfkill deps for iwl4965/5000
and removes the input device usage.
Signed-off-by: Adel Gadllah <adel.gadllah@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch removes the duplicated parsing of information elements
in ieee80211_rx_bss_info and in ieee_rx_mgmt_beacon
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Ester Kummer <ester.kummer@intel.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The old infrastructure was:
- the default algorithm is built into mac80211
- other algorithms get into their own modules
The implementation of this complicated scheme was horrible
(just look at net/mac80211/Makefile), and anyone adding a new
algorithm would most likely not get it right at his first attempt.
This patch therefore builds all enabled algorithms into the mac80211
module.
The user interface for the rate control algorithms changes as follows:
- first the user can choose which algorithms to enable (currently only
MAC80211_RC_PID is available)
- if more than one algorithm is enabled (currently not possible since
only one algorithm is present) the user then chooses the default one
Note:
- MAC80211_RC_PID is always enables for CONFIG_EMBEDDED=n
Technical changes:
- all selected algorithms get into the mac80211 module
- net/mac80211/Makefile can now become much less complicated
- support for rc80211_pid_algo.c being modular is no longer required
- this includes unexporting mesh_plink_broken
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds the interval between the scan results and the last time a
beacon was received in the result of the scan.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch add spectrum capability and required information
elements to association request providing AP has requested it and
it is supported by the driver
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Assaf Krauss <assaf.krauss@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The patch introduces MAC80211_VERBOSE_SPECT_MGMT_DEBUG Kconfig option to
suppress Spectrum Management 802.11h related debug logs.
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This driver supports video input devices compliant with the USB Video Class
specification. This means lots of currently manufactured webcams, and probably
most of the future ones.
Signed-off-by: Laurent Pinchart <laurent.pinchart@skynet.be>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch makes mac80211 refuse a WEP key whose length is not WEP40 nor
WEP104.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Rewrite AID calculation in handle_pspoll() to avoid truncating bits.
Make hostap_80211_header_parse() static, don't export it. Avoid
shadowing variables.
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
DEBUG_EXTRA is reported to the kernel log by default, but DEBUG_EXTRA2
is not. Unrelated WDS frames pollute the log unnecessarily.
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The current logic has a bug which cannot find matching pattern, if the
pattern is matched from the first character of target string.
for example:
pattern=abc, string=abcdefg
pattern=a, string=abcdefg
Searching algorithm should return 0 for those things.
Signed-off-by: Joonwoo Park <joonwpark81@gmail.com>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Lost connections was reported by Thomas Bätzler (running 2.6.25 kernel) on
the netfilter mailing list (see the thread "Weird nat/conntrack Problem
with PASV FTP upload"). He provided tcpdump recordings which helped to
find a long lingering bug in conntrack.
In TCP connection tracking, checking the lower bound of valid ACK could
lead to mark valid packets as INVALID because:
- We have got a "higher or equal" inequality, but the test checked
the "higher" condition only; fixed.
- If the packet contains a SACK option, it could occur that the ACK
value was before the left edge of our (S)ACK "window": if a previous
packet from the other party intersected the right edge of the window
of the receiver, we could move forward the window parameters beyond
accepting a valid ack. Therefore in this patch we check the rightmost
SACK edge instead of the ACK value in the lower bound of valid (S)ACK
test.
Signed-off-by: Jozsef Kadlecsik <kadlec@blackhole.kfki.hu>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that we support warm-plug mate port will be registered
even if there are no devices attached to it.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
This reverts commit ac1623625c.
It was premature to remove it now, we will do it post-2.6.26.
Thanks to Russell King for noticing the issue.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
This patch annotates the platform_secondary_init function in
arch/arm/mach-realview/platsmp.c with trace_hardirqs_off to avoid a
warning when LOCKDEP and TRACE_IRQFLAGS are enabled.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
ptrace GET/SET FPXREGS broken
x86: fix cpu hotplug crash
x86: section/warning fixes
x86: shift bits the right way in native_read_tscp
The newly added event_lock spinlock in the input core disallows sleeping
and therefore using mutexes in event handlers. Convert force-feedback
core to rely on event_lock instead of mutex to protect slots allocated
for fore-feedback effects. The original mutex is still used to serialize
uploading and erasing of effects.
Reported-by: Anssi Hannula <anssi.hannula@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This patch adds the Repeat key to the input layer. The usage
in the HUT is 0xBC (listed under "15.7 Transport Controls").
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
When I update kernel 2.6.25 from 2.6.24, gdb does not work.
On 2.6.25, ptrace(PTRACE_GETFPXREGS, ...) returns ENODEV.
But 2.6.24 kernel's ptrace() returns EIO.
It is issue of compatibility.
I attached test program as pt.c and patch for fix it.
#include <stdio.h>
#include <stdlib.h>
#include <unistd.h>
#include <signal.h>
#include <errno.h>
#include <sys/ptrace.h>
#include <sys/types.h>
struct user_fxsr_struct {
unsigned short cwd;
unsigned short swd;
unsigned short twd;
unsigned short fop;
long fip;
long fcs;
long foo;
long fos;
long mxcsr;
long reserved;
long st_space[32]; /* 8*16 bytes for each FP-reg = 128 bytes */
long xmm_space[32]; /* 8*16 bytes for each XMM-reg = 128 bytes */
long padding[56];
};
int main(void)
{
pid_t pid;
pid = fork();
switch(pid){
case -1:/* error */
break;
case 0:/* child */
child();
break;
default:
parent(pid);
break;
}
return 0;
}
int child(void)
{
ptrace(PTRACE_TRACEME);
kill(getpid(), SIGSTOP);
sleep(10);
return 0;
}
int parent(pid_t pid)
{
int ret;
struct user_fxsr_struct fpxregs;
ret = ptrace(PTRACE_GETFPXREGS, pid, 0, &fpxregs);
if(ret < 0){
printf("%d: %s.\n", errno, strerror(errno));
}
kill(pid, SIGCONT);
wait(pid);
return 0;
}
/* in the kerel, at kernel/i387.c get_fpxregs() */
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Vegard Nossum reported crashes during cpu hotplug tests:
http://marc.info/?l=linux-kernel&m=121413950227884&w=4
In function _cpu_up, the panic happens when calling
__raw_notifier_call_chain at the second time. Kernel doesn't panic when
calling it at the first time. If just say because of nr_cpu_ids, that's
not right.
By checking the source code, I found that function do_boot_cpu is the culprit.
Consider below call chain:
_cpu_up=>__cpu_up=>smp_ops.cpu_up=>native_cpu_up=>do_boot_cpu.
So do_boot_cpu is called in the end. In do_boot_cpu, if
boot_error==true, cpu_clear(cpu, cpu_possible_map) is executed. So later
on, when _cpu_up calls __raw_notifier_call_chain at the second time to
report CPU_UP_CANCELED, because this cpu is already cleared from
cpu_possible_map, get_cpu_sysdev returns NULL.
Many resources are related to cpu_possible_map, so it's better not to
change it.
Below patch against 2.6.26-rc7 fixes it by removing the bit clearing in
cpu_possible_map.
Signed-off-by: Zhang Yanmin <yanmin_zhang@linux.intel.com>
Tested-by: Vegard Nossum <vegard.nossum@gmail.com>
Acked-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/v4l-dvb: (42 commits)
V4L/DVB (8108): Fix open/close race in saa7134
V4L/DVB (8100): V4L/vivi: fix possible memory leak in vivi_fillbuff
V4L/DVB (8097): xc5000: check device hardware state to determine if firmware download is needed
V4L/DVB (8096): au8522: prevent false-positive lock status
V4L/DVB (8092): videodev: simplify and fix standard enumeration
V4L/DVB (8075): stv0299: Uncorrected block count and bit error rate fixed
V4L/DVB (8074): av7110: OSD transfers should not be interrupted
V4L/DVB (8073): av7110: Catch another type of ARM crash
V4L/DVB (8071): tda10023: Fix possible kernel oops during initialisation
V4L/DVB (8069): cx18: Fix S-Video and Compsite inputs for the Yuan MPC718 and enable card entry
V4L/DVB (8068): cx18: Add I2C slave reset via GPIO upon initialization
V4L/DVB (8067): cx18: Fix firmware load for case when digital capture happens first
V4L/DVB (8066): cx18: Fix audio mux input definitions for HVR-1600 Line In 2 and FM radio
V4L/DVB (8063): cx18: Fix unintended auto configurations in cx18-av-core
V4L/DVB (8061): cx18: only select tuner / frontend modules if !DVB_FE_CUSTOMISE
V4L/DVB (8048): saa7134: Fix entries for Avermedia A16d and Avermedia E506
V4L/DVB (8044): au8522: tuning optimizations
V4L/DVB (8043): au0828: add support for additional USB device id's
V4L/DVB (8042): DVB-USB UMT-010 channel scan oops
V4L/DVB (8040): soc-camera: remove soc_camera_host_class class
...
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6:
dock: bay: Don't call acpi_walk_namespace() when ACPI is disabled.
ACPI: don't walk tables if ACPI was disabled
thermal: Create CONFIG_THERMAL_HWMON=n
Removed vmlinux* rule because it matches too many useful files, replacing
it with rules matching filetype by filename (e.g. *.gz). Also unignored
.mailmap from the top directory. Added a comment telling the user how to
check for tracked files being ignored.
Signed-off-by: Eduard - Gabriel Munteanu <eduard.munteanu@linux360.ro>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'audit.b52' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/audit-current:
[PATCH] remove useless argument type in audit_filter_user()
[PATCH] audit: fix kernel-doc parameter notation
[PATCH] kernel/audit.c: nlh->nlmsg_type is gotten more than once
It will almost unavoidably cause some breakage but it
is long overdue.
The driver identification string has been updated, a
lost tabulation and some unused code have been removed.
Otherwise the code paths should stay the same.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Edward Hsu <edward_hsu@realtek.com.tw>
The layout of the 8168 serie is different from that of the 8110 one.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Edward Hsu <edward_hsu@realtek.com.tw>
the CPU hotplug problems (crashes under high-volume unplug+replug
tests) seem to be related to migrate_dead_tasks().
Firstly I added traces to see all tasks being migrated with
migrate_live_tasks() and migrate_dead_tasks(). On my setup the problem
pops up (the one with "se == NULL" in the loop of
pick_next_task_fair()) shortly after the traces indicate that some has
been migrated with migrate_dead_tasks()). btw., I can reproduce it
much faster now with just a plain cpu down/up loop.
[disclaimer] Well, unless I'm really missing something important in
this late hour [/desclaimer] pick_next_task() is not something
appropriate for migrate_dead_tasks() :-)
the following change seems to eliminate the problem on my setup
(although, I kept it running only for a few minutes to get a few
messages indicating migrate_dead_tasks() does move tasks and the
system is still ok)
Signed-off-by: Ingo Molnar <mingo@elte.hu>
synchronize_irq() is superfluous when free_irq() call immediately follows it,
because free_irq() also does a synchronize_irq() call of its own.
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Clean up config/burst value arch-specific setup.
* bcrvalue only varied by its big-endian bit
* crvalue only varied for certain types of x86-32 chips
This should make fealnx quite a bit more portable, without any behavior
change.
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
DE_UNALIGNED_16 is always being passed a u16 *, no need to have the
wrapper with two casts in it, just call get_unaligned directly.
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This patch is the minimal amount of code needed to support
wake-on-lan in platform mode properly (i.e. "ethtool -s eth0 wol g"
is sufficient, no additional magic needed) for me.
This is derived from David Brownells patch
(http://lists.laptop.org/pipermail/devel/2007-April/004691.html).
However I decided to move the hook into pci-acpi.c since the other
two pci hooks also live there and pci and acpi are the only users of
the platform_enable_wakeup-hook.
As a 'side-effect' this also makes wake on usb activity work for me
and I had to disable usb wakeup (which is enabled by default) using
the power/wakeup sysfs functionality ("echo disabled >
${sysfs_path_to_device}/power/wakeup").
(BTW I first thought the 'immediate reboot because of usb wake' effect is
caused by the optical mouse generating a wake event, but it rather
seems to be a problem with a flaky secondary usb host controller,
which sees a connected device where nothing is attached)
Signed-off-by: Tobias Diedrich <ranma+kernel@tdiedrich.de>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
We currently don't signal the kernel we that this device can wake
the system. Call device_init_wakeup() to correct this.
Without this device_can_wakeup and device_may_wakeup will return
incorrect values.
Together with the minimized acpi wakeup patch (6/4 ;)), which will
follow in the next mail, this really makes wake-on-lan work for me
as expected (i.e. "ethtool -s eth0 wol g" is sufficient, no
additional magic needed).
Signed-off-by: Tobias Diedrich <ranma+kernel@tdiedrich.de>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Clean up the following errors and warnings reported by checkpatch.pl:
+ ERROR: Macros with complex values should be enclosed in parenthesis
+ WARNING: __func__ should be used instead of gcc specific __FUNCTION__
+ WARNING: plain inline is preferred over __inline__
+ WARNING: Use #include <linux/io.h> instead of <asm/io.h>
+ WARNING: Use #include <linux/uaccess.h> instead of <asm/uaccess.h>
The changes were verified with by comparing the "objdump -d 8139too.ko"
output which is exactly the same for the old and new version in case of
config CONFIG_8139TOO=m, CONFIG_8139TOO_PIO=n, CONFIG_8139TOO_TUNE_TWISTER=n,
CONFIG_8139TOO_8129=n, CONFIG_8139_OLD_RX_RESET=n.
Software versions used: gcc 4.2.3, objdump 2.18.0.20080103, on elf32-i386.
Signed-off-by: Márton Németh <nm127@freemail.hu>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Pass buffer length to rndis_command so that rndis_command can read full
response buffer from device instead of max CONTROL_BUFFER_SIZE bytes.
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Fix compile error on sh_eth and remove base address macro.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
