htcpld_register_chip_i2c() misses to call i2c_put_adapter() in an error
path. Add the missed function call to fix it.
Fixes: 6048a3dd23 ("mfd: Add HTCPLD driver")
Signed-off-by: Jing Xiangfeng <jingxiangfeng@huawei.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
There are no separate serial/SPI devices under the at91-usart MFD, but
actually the MFD is used as a serial or a SPI device. There are no DT
sub-nodes for the MFD children, so we should use platform device API to
register the drivers.
Suggested-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@microchip.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
An errata exists for cs47l15 where the reset must be handled
differently and removed before DCVDD is applied. A soft reset is used
for situations where a reset is required to reset state. This does
however, make this part unsuitable for DCVDD supplies with a rise time
greater than 2mS.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The DCVDD supply does not always power down when the CODEC enters
suspend, for example shared regulators or always-on regulators. In
these cases if a register is written back to the default value whilst
the CODEC is in suspend that register will retain the previous value.
As DCVDD never powered down, the register retains its old value and
as the cache sync only synchronises registers that differ from the
default the new value is never written out.
Ensure the registers are in the expected state after suspend by always
resetting the CODEC on resume. This also has the benefit of being
recommended by the datasheet for DCVDD supplies that take longer than
2mS to rise.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
CHECK: Alignment should match open parenthesis
#24: FILE: drivers/mfd/tps65910.c:296:
+ ret = regmap_clear_bits(tps65910->regmap, TPS65910_DEVCTRL,
DEVCTRL_CK32K_CTRL_MASK);
CHECK: Alignment should match open parenthesis
#33: FILE: drivers/mfd/tps65910.c:318:
+ ret = regmap_set_bits(tps65910->regmap, TPS65910_DEVCTRL,
DEVCTRL_DEV_SLP_MASK);
CHECK: Alignment should match open parenthesis
#42: FILE: drivers/mfd/tps65910.c:326:
+ ret = regmap_set_bits(tps65910->regmap,
TPS65910_SLEEP_KEEP_RES_ON,
CHECK: Alignment should match open parenthesis
#51: FILE: drivers/mfd/tps65910.c:336:
+ ret = regmap_set_bits(tps65910->regmap,
TPS65910_SLEEP_KEEP_RES_ON,
CHECK: Alignment should match open parenthesis
#60: FILE: drivers/mfd/tps65910.c:346:
+ ret = regmap_set_bits(tps65910->regmap,
TPS65910_SLEEP_KEEP_RES_ON,
CHECK: Alignment should match open parenthesis
#69: FILE: drivers/mfd/tps65910.c:358:
+ regmap_clear_bits(tps65910->regmap, TPS65910_DEVCTRL,
DEVCTRL_DEV_SLP_MASK);
CHECK: Alignment should match open parenthesis
#78: FILE: drivers/mfd/tps65910.c:440:
+ if (regmap_set_bits(tps65910->regmap, TPS65910_DEVCTRL,
DEVCTRL_PWR_OFF_MASK) < 0)
CHECK: Alignment should match open parenthesis
#83: FILE: drivers/mfd/tps65910.c:444:
+ regmap_clear_bits(tps65910->regmap, TPS65910_DEVCTRL,
DEVCTRL_DEV_ON_MASK);
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Remove wrappers around regmap calls to remove now-useless indirection.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Use regmap accessors directly for register manipulation - removing
one layer of abstraction.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Add the subtype and compatible strings for PM660 and PM660L,
found in various SoCs, including SDM630, SDM636, SDM660 and
SDA variants.
Signed-off-by: AngeloGioacchino Del Regno <kholk11@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Constify a number of static struct resource. The only usage of the
structs are to assign their address to the resources field in the
mfd_cell struct. This allows the compiler to put them in read-only
memory. Done with the help of Coccinelle.
Signed-off-by: Rikard Falkeborn <rikard.falkeborn@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Constify adc_resources[]. The only usage is to assign its address to the
resources field of the mfd_cell struct. This allows the compiler to put
it in read-only memory. Done with the help of Coccinelle.
Signed-off-by: Rikard Falkeborn <rikard.falkeborn@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Constify a couple of static struct resource. The only usage of the
structs is to assign their address to the resources field in the
mfd_cell struct. This allows the compiler to put them in read-only
memory. Done with the help of Coccinelle.
Signed-off-by: Rikard Falkeborn <rikard.falkeborn@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Constify a couple of static struct resource. The only usage of the
structs is to assign their address to the resources field in the
mfd_cell struct. This allows the compiler to put them in read-only
memory. Done with the help of Coccinelle.
Signed-off-by: Rikard Falkeborn <rikard.falkeborn@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Constify a number of static struct resource. The only usage of the
structs are to assign their address to the resources field in the
mfd_cell struct. This allows the compiler to put them in read-only
memory. Done with the help of Coccinelle.
Signed-off-by: Rikard Falkeborn <rikard.falkeborn@gmail.com>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Constify a number of static struct resource. The only usage of the
structs are to assign their address to the resources field in the
mfd_cell struct. This allows the compiler to put them in read-only
memory. Done with the help of Coccinelle.
Signed-off-by: Rikard Falkeborn <rikard.falkeborn@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Constify a number of static struct resource. The only usage of the
structs are to assign their address to the resources field in the
mfd_cell struct. This allows the compiler to put them in read-only
memory. Done with the help of Coccinelle.
Signed-off-by: Rikard Falkeborn <rikard.falkeborn@gmail.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Constify a number of static struct resource. The only usage of the
structs are to assign their address to the resources field in the
mfd_cell struct. This allows the compiler to put them in read-only
memory. Done with the help of Coccinelle.
Signed-off-by: Rikard Falkeborn <rikard.falkeborn@gmail.com>
Acked-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This adds syscon_regmap_lookup_by_phandle_optional() function to get an
optional regmap.
It behaves the same as syscon_regmap_lookup_by_phandle() except where
there is no regmap phandle. In this case, instead of returning -ENODEV,
the function returns NULL. This makes error checking simpler when the
regmap phandle is optional.
Suggested-by: Nicolas Boichat <drinkcat@chromium.org>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Intel Platform Monitoring Technology (PMT) is an architecture for
enumerating and accessing hardware monitoring facilities. PMT supports
multiple types of monitoring capabilities. This driver creates platform
devices for each type so that they may be managed by capability specific
drivers (to be introduced). Capabilities are discovered using PCIe DVSEC
ids. Support is included for the 3 current capability types, Telemetry,
Watcher, and Crashlog. The features are available on new Intel platforms
starting from Tiger Lake for which support is added. This patch adds
support for Tiger Lake (TGL), Alder Lake (ADL), and Out-of-Band Management
Services Module (OOBMSM).
Also add a quirk mechanism for several early hardware differences and bugs.
For Tiger Lake and Alder Lake, do not support Watcher and Crashlog
capabilities since they will not be compatible with future product. Also,
fix use a quirk to fix the discovery table offset.
Co-developed-by: Alexander Duyck <alexander.h.duyck@linux.intel.com>
Signed-off-by: Alexander Duyck <alexander.h.duyck@linux.intel.com>
Signed-off-by: David E. Box <david.e.box@linux.intel.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
drivers/mfd/kempld-core.c:556:36: warning: unused variable 'kempld_acpi_table' [-Wunused-const-variable]
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Fixes the following randconfig build error:
ld: drivers/mfd/simple-mfd-i2c.o: in function `simple_mfd_i2c_probe':
simple-mfd-i2c.c:(.text+0x48): undefined reference to `__devm_regmap_init_i2c'
ld: drivers/mfd/simple-mfd-i2c.o: in function `simple_mfd_i2c_driver_init':
simple-mfd-i2c.c:(.init.text+0x14): undefined reference to `i2c_register_driver'
ld: drivers/mfd/simple-mfd-i2c.o: in function `simple_mfd_i2c_driver_exit':
simple-mfd-i2c.c:(.exit.text+0xd): undefined reference to `i2c_del_driver'
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Tested-by: Randy Dunlap <rdunlap@infradead.org> # build-tested
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Build this driver on another platforms if COMPILE_TEST=y. Another
drivers may depend on this, for example leds-asic3.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Recent Kontron COMe modules identify the PLD device using the hardware
id KEM0001 in the ACPI table.
This patch adds support for probing the device using the HID and also
retrieving the resources.
As this is not available for all products, the DMI based detection still
needs to be around for older systems. It is executed if no matching ACPI
HID is found during registering the platform driver or no specific
device id is forced.
If a device is detected using ACPI and no resource information is
available, the default io resource is used.
Forcing a device id with the force_device_id parameter and therefore
manually generating a platform device takes precedence over ACPI during
probing.
Signed-off-by: Michael Brunner <michael.brunner@kontron.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This patch implements the basic functions of the BMC chip for some Intel
FPGA PCIe Acceleration Cards (PAC). The BMC is implemented using the
Intel MAX 10 CPLD.
This BMC chip is connected to the FPGA by a SPI bus. To provide direct
register access from the FPGA, the "SPI slave to Avalon Master Bridge"
(spi-avmm) IP is integrated in the chip. It converts encoded streams of
bytes from the host to the internal register read/write on the Avalon
bus. So This driver uses the regmap-spi-avmm for register accessing.
Signed-off-by: Xu Yilun <yilun.xu@intel.com>
Signed-off-by: Wu Hao <hao.wu@intel.com>
Signed-off-by: Matthew Gerlach <matthew.gerlach@linux.intel.com>
Signed-off-by: Russ Weight <russell.h.weight@intel.com>
Reviewed-by: Tom Rix <trix@redhat.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Add support for the LP87524B/J/P-Q1 Four 4-MHz Buck Converter. This is a
variant of the LP87565 having 4 single-phase outputs and up to 10 A of
total output current.
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This file does not make use of it.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This code should clean up if sm501_init_dev() fails.
Fixes: b6d6454fdb ("[PATCH] mfd: SM501 core driver")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The name allocated for the regmap_config structure is freed
pretty early, right after the registration of the MMIO region.
Unfortunately, that doesn't follow the life cycle that debugfs
expects, as it can access the name field long after the free
has occurred.
Move the free on the error path, and keep it forever otherwise.
Fixes: e15d7f2b81 ("mfd: syscon: Use a unique name with regmap_config")
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
When changing to use suspend-to-idle to save power, the PMIC irq can not
wakeup the system due to lack of wakeup capability, which will cause
the sub-irqs (such as power key) of the PMIC can not wake up the system.
Thus we can add the wakeup capability for PMIC irq to solve this issue,
as well as removing the IRQF_NO_SUSPEND flag to allow PMIC irq to be
a wakeup source.
Reported-by: Chunyan Zhang <zhang.lyra@gmail.com>
Signed-off-by: Baolin Wang <baolin.wang7@gmail.com>
Tested-by: Chunyan Zhang <chunyan.zhang@unisoc.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Add PCI IDs for Lakefield to the list of supported UARTs.
Cc: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Cc: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: "Ravi V. Shankar" <ravi.v.shankar@intel.com>
Signed-off-by: Ricardo Neri <ricardo.neri-calderon@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This converts the DaVinci DM355EVM LEDs to use GPIO descriptor look-ups.
Cc: Sekhar Nori <nsekhar@ti.com>
Cc: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Common pattern of handling deferred probe can be simplified with
dev_err_probe(). Less code and also it prints the error value.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Common pattern of handling deferred probe can be simplified with
dev_err_probe(). Less code and also it prints the error value.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Common pattern of handling deferred probe can be simplified with
dev_err_probe(). Less code and also it prints the error value.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This driver provides access to the EC RAM of said embedded controller
attached to the I2C bus as well as optionally supporting its slightly weird
power-off/restart protocol.
A particular implementation of the EC firmware can be identified by a
model byte. If this driver identifies the Dell Ariel platform, it
registers the appropriate cells.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
When testing with !OF, the build system reports:
>> drivers/mfd/khadas-mcu.c:125:34: warning: unused variable 'khadas_mcu_of_match' [-Wunused-const-variable]
static const struct of_device_id khadas_mcu_of_match[] = {
^
Reported-by: kernel test robot <lkp@intel.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The RN5T618 and RC5T619 both have a charger and a fuel gauge, so add
a subdevice for it. According to drivers in the wild, things
should be at least similar, but since it is not tested, add it
only to the RC5T619.
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Add the core support for the board management controller found on the
SMARC-sAL28 board.
Also add a virtual symbol which pulls in the simple-mfd-i2c driver and
provide a common symbol on which the subdevice drivers can depend on.
At the moment, this controller is used on the Kontron SMARC-sAL28 board.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
There are I2C devices which contain several different functions but
doesn't require any special access functions. For these kind of drivers
an I2C regmap should be enough.
Create an I2C driver which creates an I2C regmap and enumerates its
children. If a device wants to use this as its MFD core driver, it has
to add an individual compatible string. It may provide its own regmap
configuration.
Subdevices can use dev_get_regmap() on the parent to get their regmap
instance.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Commit e49aa9a9bd22 ("mfd: core: Make a best effort attempt to match
devices with the correct of_nodes") changed the semantics for disabled
devices in mfd_add_device(). Instead of silently ignoring a disabled
child device, an error was returned. On receipt of the error
mfd_add_devices() the precedes to remove *all* child devices and
returns an all-failed error to the caller, which will inevitably fail
the parent device as well.
This patch reverts back to the old semantics and ignores child devices
which are disabled in Device Tree.
Fixes: e49aa9a9bd22 ("mfd: core: Make a best effort attempt to match devices with the correct of_nodes")
Reported-by: Icenowy Zheng <icenowy@aosc.io>
Tested-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The pdev.mfd_cell is released by platform_device_release(), which is
invoked by platform_device_unregister(). Hence mfd_remove_devices_fn()
shouldn't release the cell variable. The double-free bug is reported KASAN
during of MFD driver module removal.
Fixes: 466a62d764 ("mfd: core: Make a best effort attempt to match devices with the correct of_nodes")
Reported-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
- Make better attempt at matching device with the correct OF node
- Allow batch removal of hierarchical sub-devices
- New Drivers
- Add STM32 Clocksource driver
- Add support for Khadas System Control Microcontroller
- Driver Removal
- Remove unused driver for TI's SMSC ECE1099
- New Device Support
- Add support for Intel Emmitsburg PCH to Intel LPSS PCI
- Add support for Intel Tiger Lake PCH-H to Intel LPSS PCI
- Add support for Dialog DA revision to Dialog DA9063
- New Functionality
- Add support for AXP803 to be probed by I2C
- Fix-ups
- Numerous W=1 warning fixes
- Device Tree changes; stm32-lptimer, gateworks-gsc, khadas,mcu, stmfx, cros-ec, j721e-system-controller
- Enabled Regmap 'fast I/O'; stm32-lptimer
- Change BUG_ON to WARN_ON; arizona-core
- Remove superfluous code/initialisation; madera, max14577
- Trivial formatting/spelling issues; madera-core, madera-i2c, da9055, max77693-private
- Switch to of_platform_populate(); sprd-sc27xx-spi
- Expand out set/get brightness/pwm macros; lm3533-ctrlbank
- Disable IRQs on suspend; motorola-cpcap
- Clean-up error handling; intel_soc_pmic_mrfld
- Ensure correct removal order of sub-devices; madera
- Many s/HTTP/HTTPS/ link changes
- Ensure name used with Regmap is unique; syscon
- Bug Fixes
- Properly 'put' clock on unbind and error; arizona-core
- Fix revision handling; da9063
- Fix 'assignment of read-only location' error; kempld-core
- Avoid using the Regmap API when atomic; rn5t618
- Redefine volatile register description; rn5t618
- Use locking to protect event handler; dln2
-----BEGIN PGP SIGNATURE-----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=X/Zn
-----END PGP SIGNATURE-----
Merge tag 'mfd-next-5.9-1' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd
Pull MFD updates from Lee Jones:
"Core Frameworks
- Make better attempt at matching device with the correct OF node
- Allow batch removal of hierarchical sub-devices
New Drivers
- Add STM32 Clocksource driver
- Add support for Khadas System Control Microcontroller
Driver Removal
- Remove unused driver for TI's SMSC ECE1099
New Device Support
- Add support for Intel Emmitsburg PCH to Intel LPSS PCI
- Add support for Intel Tiger Lake PCH-H to Intel LPSS PCI
- Add support for Dialog DA revision to Dialog DA9063
New Functionality
- Add support for AXP803 to be probed by I2C
Fix-ups
- Numerous W=1 warning fixes
- Device Tree changes (stm32-lptimer, gateworks-gsc, khadas,mcu, stmfx, cros-ec, j721e-system-controller)
- Enabled Regmap 'fast I/O' in stm32-lptimer
- Change BUG_ON to WARN_ON in arizona-core
- Remove superfluous code/initialisation (madera, max14577)
- Trivial formatting/spelling issues (madera-core, madera-i2c, da9055, max77693-private)
- Switch to of_platform_populate() in sprd-sc27xx-spi
- Expand out set/get brightness/pwm macros in lm3533-ctrlbank
- Disable IRQs on suspend in motorola-cpcap
- Clean-up error handling in intel_soc_pmic_mrfld
- Ensure correct removal order of sub-devices in madera
- Many s/HTTP/HTTPS/ link changes
- Ensure name used with Regmap is unique in syscon
Bug Fixes
- Properly 'put' clock on unbind and error in arizona-core
- Fix revision handling in da9063
- Fix 'assignment of read-only location' error in kempld-core
- Avoid using the Regmap API when atomic in rn5t618
- Redefine volatile register description in rn5t618
- Use locking to protect event handler in dln2"
* tag 'mfd-next-5.9-1' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (76 commits)
mfd: syscon: Use a unique name with regmap_config
mfd: Replace HTTP links with HTTPS ones
mfd: dln2: Run event handler loop under spinlock
mfd: madera: Improve handling of regulator unbinding
mfd: mfd-core: Add mechanism for removal of a subset of children
mfd: intel_soc_pmic_mrfld: Simplify the return expression of intel_scu_ipc_dev_iowrite8()
mfd: max14577: Remove redundant initialization of variable current_bits
mfd: rn5t618: Fix caching of battery related registers
mfd: max77693-private: Drop a duplicated word
mfd: da9055: pdata.h: Drop a duplicated word
mfd: rn5t618: Make restart handler atomic safe
mfd: kempld-core: Fix 'assignment of read-only location' error
mfd: axp20x: Allow the AXP803 to be probed by I2C
mfd: da9063: Add support for latest DA silicon revision
mfd: da9063: Fix revision handling to correctly select reg tables
dt-bindings: mfd: st,stmfx: Remove I2C unit name
dt-bindings: mfd: ti,j721e-system-controller.yaml: Add J721e system controller
mfd: motorola-cpcap: Disable interrupt for suspend
mfd: smsc-ece1099: Remove driver
mfd: core: Add OF_MFD_CELL_REG() helper
...
The DT node full name is currently being used in regmap_config
which in turn is used to create the regmap debugfs directories.
This name however is not guaranteed to be unique and the regmap
debugfs registration can fail in the cases where the syscon nodes
have the same unit-address but are present in different DT node
hierarchies. Replace this logic using the syscon reg resource
address instead (inspired from logic used while creating platform
devices) to ensure a unique name is given for each syscon.
Signed-off-by: Suman Anna <s-anna@ti.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Rationale:
Reduces attack surface on kernel devs opening the links for MITM
as HTTPS traffic is much harder to manipulate.
Deterministic algorithm:
For each file:
If not .svg:
For each line:
If doesn't contain `\bxmlns\b`:
For each link, `\bhttp://[^# \t\r\n]*(?:\w|/)`:
If neither `\bgnu\.org/license`, nor `\bmozilla\.org/MPL\b`:
If both the HTTP and HTTPS versions
return 200 OK and serve the same content:
Replace HTTP with HTTPS.
Signed-off-by: Alexander A. Klimov <grandmaster@al2klimov.de>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The event handler loop must be run with interrupts disabled.
Otherwise we will have a warning:
[ 1970.785649] irq 31 handler lineevent_irq_handler+0x0/0x20 enabled interrupts
[ 1970.792739] WARNING: CPU: 0 PID: 0 at kernel/irq/handle.c:159 __handle_irq_event_percpu+0x162/0x170
[ 1970.860732] RIP: 0010:__handle_irq_event_percpu+0x162/0x170
...
[ 1970.946994] Call Trace:
[ 1970.949446] <IRQ>
[ 1970.951471] handle_irq_event_percpu+0x2c/0x80
[ 1970.955921] handle_irq_event+0x23/0x43
[ 1970.959766] handle_simple_irq+0x57/0x70
[ 1970.963695] generic_handle_irq+0x42/0x50
[ 1970.967717] dln2_rx+0xc1/0x210 [dln2]
[ 1970.971479] ? usb_hcd_unmap_urb_for_dma+0xa6/0x1c0
[ 1970.976362] __usb_hcd_giveback_urb+0x77/0xe0
[ 1970.980727] usb_giveback_urb_bh+0x8e/0xe0
[ 1970.984837] tasklet_action_common.isra.0+0x4a/0xe0
...
Recently xHCI driver switched to tasklets in the commit 36dc01657b
("usb: host: xhci: Support running urb giveback in tasklet context").
The handle_irq_event_* functions are expected to be called with interrupts
disabled and they rightfully complain here because we run in tasklet context
with interrupts enabled.
Use a event spinlock to protect event handler from being interrupted.
Note, that there are only two users of this GPIO and ADC drivers and both of
them are using generic_handle_irq() which makes above happen.
Fixes: 338a128142 ("mfd: Add support for Diolan DLN-2 devices")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The current unbinding process for Madera has some issues. The trouble
is runtime PM is disabled as the first step of the process, but
some of the drivers release IRQs causing regmap IRQ to issue a
runtime get which fails. To allow runtime PM to remain enabled during
mfd_remove_devices, the DCVDD regulator must remain available. In
the case of external DCVDD's this is simple, the regulator can simply
be disabled/put after the call to mfd_remove_devices. However, in
the case of an internally supplied DCVDD the regulator needs to be
released after the other MFD children depending on it.
Use the new MFD mfd_remove_devices_late functionality to split
the DCVDD regulator off from the other drivers.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
