This is already done by bcma in bcma_pcicore_serdes_workaround().
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Tested-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is now done by calling bcma_core_set_clockmode()
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Tested-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is now done by calling bcma_chipco_gpio_control().
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Tested-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ai_chipcontrl_epa4331 is not referenced by any method in brcmsmac and
the functionality is already in bcma_chipco_bcm4331_ext_pa_lines_ctl in
drivers/bcma/driver_chipcommon_pmu.c
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Tested-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is now done by calling bcma_core_pci_irq_ctl()
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Tested-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is now done by bcma_core_pci_config_fixup() in drivers/bcma/driver_pci.c
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Tested-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The devices I know of are not using a PCIe core with rev <= 10. The
BCM4718 uses a PCIe core with revision 14 and the BCM43224 uses a PCIe
core with revision 15. This patch removes support for old PCIe core
versions, which are not found on devices supported by brcmsmac.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Tested-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There are no devices which are using bcma and have a PCI bus, just a
PCIe bus or something else. bcma does not support PCI devices, so lets
also remove PCI support from brcmsmac. All devices currently supported
by brcmsmac are PCIe based.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Tested-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The lowest chip common version used on bcma based devices is 31 on the
bcm4718 and 32 on the bcm4313, bcm43224, and bcm43225, so the support
for the old versions could be removed.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Tested-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
bcma now provide this data and brcmsmac should get it from there and
not parse it by its self.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Tested-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
brcmsmac now takes the sprom from bcma and do not uses its own sprom
parsing any more. Remove this code as it is not used any more.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Tested-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
bcma now provides all sprom attributes needed by brcmsmac and also
parses them from the pci sprom ant otp.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Tested-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This struct contains information about the board, the chip is running
on. The struct is filled for PCIe devices and SoCs. This information is
used by b43 and will be used by brcmsmac soon.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Tested-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Previously the rev contained the revision read from the pci config
space and was used as board_rev in the wireless drivers. This is wrong
the board_rev is only fetched from the sprom accordingly to the open
source part of the Broadcom SDK and brcmsmac. This patch removes the
rev from the boardinfo structure and uses the board_rev attribute from
sprom instead. This attribute is filled by PCI, PCMCIA, SDIO and SoC
code.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Tested-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Make use of REGAINED_BSS_EVENT and instead of reporting connection
loss immediately on each BEACON_LOSE event, try if not regained
in reasonable period of time.
Signed-off-by: bartosz.markowski <bartosz.markowski@tieto.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
We currently do this:
int wl1271_cmd_build_arp_rsp(struct wl1271 *wl, struct wl12xx_vif *wlvif)
...
struct wl12xx_arp_rsp_template *tmpl;
struct ieee80211_hdr_3addr *hdr;
...
tmpl = (struct wl12xx_arp_rsp_template *)skb_put(skb, sizeof(*tmpl));
memset(tmpl, 0, sizeof(tmpl));
...
hdr = (struct ieee80211_hdr_3addr *)skb_push(skb, sizeof(*hdr));
memset(hdr, 0, sizeof(hdr));
...
I believe we want to set the entire structures to 0 with those
memset() calls, not just zero the initial part of them (size of the
pointer bytes).
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: Luciano Coelho <coelho@ti.com>
wl12xx build fails with many undefined symbol errors when MAC80211
and CFG80211 are not enabled, so make WLCORE and WL12XX depend
on MAC80211 (which already depends on CFG80211).
Here are a few of the many build errors:
drivers/built-in.o: In function `wl1271_register_hw':
main.c:(.text+0x4197cd): undefined reference to `ieee80211_register_hw'
drivers/built-in.o: In function `wl1271_rx_streaming_timer':
main.c:(.text+0x419818): undefined reference to `ieee80211_queue_work'
drivers/built-in.o: In function `wl1271_flush_deferred_work':
main.c:(.text+0x419910): undefined reference to `ieee80211_rx'
main.c:(.text+0x419938): undefined reference to `ieee80211_tx_status'
drivers/built-in.o: In function `wl12xx_op_channel_switch':
main.c:(.text+0x419afc): undefined reference to `ieee80211_chswitch_done'
drivers/built-in.o: In function `wl1271_ssid_set':
drivers/built-in.o: In function `wl1271_event_process':
event.c:(.text+0x41fec4): undefined reference to `ieee80211_sched_scan_stopped'
event.c:(.text+0x41ff88): undefined reference to `ieee80211_cqm_rssi_notify'
event.c:(.text+0x42000d): undefined reference to `ieee80211_stop_rx_ba_session'
event.c:(.text+0x420048): undefined reference to `ieee80211_stop_rx_ba_session'
event.c:(.text+0x4200b8): undefined reference to `ieee80211_chswitch_done'
event.c:(.text+0x4201ae): undefined reference to `ieee80211_find_sta'
event.c:(.text+0x4201ba): undefined reference to `ieee80211_report_low_ack'
event.c:(.text+0x42021b): undefined reference to `ieee80211_connection_loss'
drivers/built-in.o: In function `wl1271_tx_complete_packet':
tx.c:(.text+0x4206a6): undefined reference to `ieee80211_get_hdrlen_from_skb'
drivers/built-in.o: In function `wl1271_tx_fill_hdr':
tx.c:(.text+0x4208ca): undefined reference to `ieee80211_hdrlen'
drivers/built-in.o: In function `wl1271_handle_tx_low_watermark':
(.text+0x420e25): undefined reference to `ieee80211_wake_queue'
drivers/built-in.o: In function `wl12xx_rearm_rx_streaming':
(.text+0x420ed9): undefined reference to `ieee80211_queue_work'
drivers/built-in.o: In function `wl1271_tx_work_locked':
(.text+0x421008): undefined reference to `ieee80211_free_txskb'
drivers/built-in.o: In function `wl1271_rx_status.clone.2':
rx.c:(.text+0x421593): undefined reference to `ieee80211_channel_to_frequency'
drivers/built-in.o: In function `wl1271_ps_filter_frames':
ps.c:(.text+0x421a41): undefined reference to `ieee80211_tx_status'
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Cc: Luciano Coelho <coelho@ti.com>
Cc: linux-wireless@vger.kernel.org
Cc: "John W. Linville" <linville@tuxdriver.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
GFP_DMA isn't supposed to be used by itself. This allocation is allowed
to sleep so it should be ORing it with GFP_KERNEL.
Also we should check for allocations errors.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Use FW RX data filters to support cfg80211 wowlan wakeup patterns.
This enables to wake up the host from suspend following detection
of certain configurable patterns within an incoming packet.
Up to 5 patterns are supported. Once the host is resumed
any configured RX data filter is cleared.
A single pattern can match several bytes sequences with different
offsets within a packet.
Signed-off-by: Eyal Shapira <eyal@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
More prep work to support wowlan wakeup patterns.
Added some wrappers that also keep the current filters state
updated in the driver.
Signed-off-by: Eyal Shapira <eyal@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
More prep work for wowlan patterns.
Added ACXs to set global RX filter behavior and
enable or disable a specific filter.
Signed-off-by: Eyal Shapira <eyal@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
This is prep work for the support of wowlan patterns
using the FW data rx filters mechanism.
Added an rx filter struct and some util functions
required to manipulate it.
Signed-off-by: Eyal Shapira <eyal@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
GFP_DMA should not be used by itself, it still needs GFP_KERNEL or
such. Fix two occurrences of allocations with GFP_DMA only.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
There is a dummy read of a PCI MMIO register that occurs before the SSB bus
has been powered, which is an error. This bug has not been seen earlier,
but was apparently exposed when udev was updated to version 182.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use the newly introduced brcmf_sdio_regrl to replace
brcmf_sdioh_card_regread as part of the SDIO WiFi dongle register
access interface clean up.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The new interface brcmf_sdio_regr/w provides result of access
attempts. It is no longer necessary to use dedicated variable
and function to provide enquiry for failure.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The new brcmf_sdio_regrl/regwl interface has already performed
retries on failed attempts. It is no longer necessary to have the
retry mechanism in r_sdreg32/w_sdreg32.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use the newly introduced brcmf_sdio_regwl to replace
brcmf_sdcard_reg_write as part of the SDIO WiFi dongle register
access interface clean up.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use the newly introduced brcmf_sdio_regrl to replace
brcmf_sdcard_reg_read as part of the SDIO WiFi dongle register
access interface clean up.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use the newly introduced brcmf_sdio_regwb to replace
brcmf_sdcard_cfg_write as part of the SDIO WiFi dongle register
access interface clean up.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use the newly introduced brcmf_sdio_regrb to replace
brcmf_sdcard_cfg_read as part of the SDIO WiFi dongle register
access interface clean up.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Both brcmf_sdcard_cfg_read/write and brcmf_sdcard_reg_read/write
are used as interface functions for register access of SDIO WiFi
dongle. A unified interface brcmf_sdio_regr/w is introduced in
this patch in order to simplify the interface and keep the
complexity within the lower layer.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
brcmf_sdcard_set_sbaddr_window configures 3 registers on SDIO
function misc bank to change current silicon backplane programming
window. This patch makes it call brcmf_sdioh_request_byte directly
in order to prepare for the write register interface unification.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The size parameter for brcmf_sdcard_reg_write is always 4. Remove it
to make the code cleaner.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The size parameter for brcmf_sdcard_reg_read is always 4. Remove it
to make the code neat.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes multiple issues with the current RTT
implementation in ath9k.
* The data that is obtained from the RTT interface registers
are stored in 31:5 - mask out the extra bits when reading them.
* A history buffer is maintained which is not needed at all.
Remove this array and just store the baseband data for each
chain (or bank).
* A 'num_readings' variable was being used to handle the
last entry. But it was being used in an improper manner, with
the result that the RTT values were never being written
to the RTT Interface registers. Fix this by using a simple
flag.
* Stop baseband operations before programming the calibration values
to the HW.
* Do not restore RX gain settings as part of RTT.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If the BA session is torn down before we had a chance to start it
we shouldn't disable the AGG tx queues that weren't enabled.
This can happen in two cases:
1) We get a delBA before we drained our Tx queues in agg start flow
2) We didn't get the (successfull) addBA response on time
Reported-by: Daniel Chyan <dchyan@princeton.edu>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We have TX_REPLY for that.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The power index that the user gives as module parameter
in in range 1-5, but we need to decrease it in order
to create an array index out of it (0-4) for the power
table command.
Signed-off-by: Amit Beka <amit.beka@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Once driver decide to change reduced tx power behavior,
make sure the reduce tx power valid bit is set
Change-Id: I3afae96319292d8cb347a812a948085c5db7ad91
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Reviewed-on: http://git-mwg.jer.intel.com/gerrit/1948
Tested-by: Jenkins
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In bt coex, consider the average rssi as part of decision making process
Change-Id: I8d11d7f177a6875e2a9d08f7539d42253226fd7a
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Reviewed-on: http://git-mwg.jer.intel.com/gerrit/1945
Tested-by: Jenkins
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Documentation/CodingStyle says
"Do not unnecessarily use braces where a single statement will do."
Use "switch/case", instead of "if/else_if/else", so that more cases
can be added later.
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Drivers need to report the number of transmission attempts for each rate
as well as to terminate the rate array with -1. The in-kernel datapath
of hwsim simulates a perfect medium, therefore the driver only needs to
report that the first transmission attempt was sucessfully completed at
the most favorable rate.
Rate control is working again for this driver. Tested mesh mode with
minstrel.
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some sdio host controllers do not support real in band interrupt.
Software polling mode as a replacement is not fast enough for
high throughput and new features. Also some in band interrupts
do not support host wake up on embedded platform even when they
are real physical interrupts. Therefore out of band (oob)
interrupt mechanism is implemented for these scenarios.
To provide oob irq number and flags used for irq registration in
brcmfmac, a platform device contains irq resource must be
registered in board specific code.
Here is an example of platform device structure:
struct resource brcmf_sdio_res[] = {
{
.start = GPIO_BRCMF_SDIO_OOB_NUM,
.end = GPIO_BRCMF_SDIO_OOB_NUM,
.flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHLEVEL,
}
};
struct platform_device brcmf_sdio_device = {
.name = "brcmf_sdio_pd",
.id = -1,
.num_resources = ARRAY_SIZE(brcmf_sdio_res),
.resource = brcmf_sdio_res,
};
Reviewed-by: pieter-paul giesberts <pieterpg@broadcom.com>
Reviewed-by: arend van spriel <arend@broadcom.com>
Signed-off-by: franky lin <frankyl@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For out of band interrupt which is going to be introduced shortly,
the interrupt register function must be called after firmware is
downloaded. This patch moves it from brcmf_sdbrcm_probe to
brcmf_sdbrcm_bus_init.
Reviewed-by: pieter-paul giesberts <pieterpg@broadcom.com>
Reviewed-by: arend van spriel <arend@broadcom.com>
Signed-off-by: franky lin <frankyl@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Bus state should be the correct flag for bus status. Use it instead
of result from previous function call for backplane clock switch.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
