Even if struct snd_dmaengine_pcm_config is used, prepare_slave_config()
callback might not be set. Check if this callback is set before using it.
Fixes: fa654e0853 ("ASoC: dmaengine-pcm: Provide default config")
Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@microchip.com>
Link: https://lore.kernel.org/r/20220307122202.2251639-2-codrin.ciubotariu@microchip.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Merge series from Sascha Hauer <s.hauer@pengutronix.de>:
This series has some updates for the fsl_sai driver: Some general
cleanup patches, a bugfix in the ip revision checking and finally
the mclk setting is made more accurate and support for 1:1 bclk:mclk
setting is added.
Merge series from Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>:
Updates to clean-up the GPIOLIB dependency and a quirk for HP
SoundWire devices.
Merge series from Richard Fitzgerald <rf@opensource.cirrus.com>:
This adds support for I2S/TDM links where the slot width varies
depending on the sample width, in a way that cannot be guessed by
component hw_params().
A typical example is:
- 16-bit samples use 16-bit slots
- 24-bit samples use 32-bit slots
There is no way for a component hw_params() to deduce from the information
it is passed that 24-bit samples will be in 32-bit slots.
Some audio hardware cannot support a fixed slot width or a slot width
equal to the sample width in all cases. This is usually due either to
limitations of the audio serial port or system clocking restrictions.
Merge series from Stephan Gerhold <stephan@gerhold.net>:
This series adds a simple driver and DT schema for the Awinic AW8738
audio amplifier. It's fairly simple - the main difference to
simple-amplifier is that there is a "one-wire pulse control" that
allows configuring the amplifier to one of a few pre-defined modes.
This can be used to configure the speaker-guard function (primarily
the power limit for the amplifier).
The "adata->i2s_irq" variable is unsigned so the error handling
will not work.
Fixes: 87d71a1287 ("ASoC: amd: pcm-dma: Use platform_get_irq() to get the interrupt")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://lore.kernel.org/r/20220304131256.GA28739@kili
Signed-off-by: Mark Brown <broonie@kernel.org>
DETECT_MODE and PLL_START must be zero while HP_PDN and ADC_PDN are
both 1. If this condition is broken it can discharge FILT+ and it
can then take up to 1 second for FILT+ to recharge.
There is no workaround required for this, simply avoiding settings
and sequences that would break the requirement. The driver already
meets the requirement.
But it is not obvious from reading the code that this requirement
exists, or what is ensuring it is met. So it would not currently be
obvious to someone changing the code that there is certain special
behaviour that must be maintained.
To avoid accidental breakage in the future:
- Add comments into the register definitions to warn about this so
that anyone changing the code around DETECT_MODE and PLL_START is
aware of this requirement.
- Add a comment where PLL_START is written to 1 to highlight the
requirement and why it is satisfied.
- Add a comment in cs42l42_setup_hs_type_detect() when DETECT_MODE is
initialized.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20220304144015.398656-1-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The parts supported by this driver can have product-specific
firmware and tunings files. Typically these have been used on
embedded systems where the manufacturer is responsible for
installing the correct product-specific firmware files into
/lib/firmware. However, the linux-firmware repository places all
available firmwares into /lib/firmware and it is up to the driver to
select the correct product-specific firmware from that directory.
For example a product containing four smart amplifiers may provide
firmware specific for that product and each of the amplifiers may
have coefficient files containing tunings for their placement in the
mechanical design.
This change extends firmware (wmfw) and coefficient (bin) filenames
to be of the general form:
<cirrus/>part-dspN-fwtype<-system_name<-asoc_component_prefix>>.type
Where the cirrus subdirectory, system_name and asoc_component_prefix
are optional.
New files will be placed in the cirrus subdirectory to avoid
polluting the main /lib/firmware/ location. The generic name must be
searched in /lib/firmware before /lib/firmware/cirrus so that a
generic file in the new location does not override existing
product-specific files in the legacy location.
The search order for firmware files is:
- cirrus/part-dspN-fwtype-system_name-asoc_component_prefix.wmfw
- cirrus/part-dspN-fwtype-system_name.wmfw
- part-dspN-fwtype.wmfw
- cirrus/part-dspN-fwtype.wmfw
- Qualifications are added to the filename so that rightwards is more
specific.
- The system_name is provided by the codec driver.
- The asoc_component_prefix is used to identify tunings for individual
parts because it would already exist to disambiguate the controls
and it makes it obvious which firmware file applies to which device.
The optional coefficient file must have the same filename
construction as the discovered wmfw except:
- where the wmfw has only system_name then the bin file can
optionally include the asoc_component_prefix. This is to allow a
common wmfw for all amps but separate tunings per amp.
Signed-off-by: Simon Trimmer <simont@opensource.cirrus.com>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20220303155016.122125-1-simont@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
As the potential failure of the clk_enable(),
it should be better to check it and return error
if fails.
Fixes: ab6f6d8521 ("ASoC: fsi: add master clock control functions")
Signed-off-by: Jiasheng Jiang <jiasheng@iscas.ac.cn>
Link: https://lore.kernel.org/r/20220302062844.46869-1-jiasheng@iscas.ac.cn
Signed-off-by: Mark Brown <broonie@kernel.org>
This device only has 4 TX channels.
Fixes: fe1024d504 ("ASoC: cs35l41: Combine adjacent register writes")
Signed-off-by: Lucas Tanure <tanureal@opensource.cirrus.com>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20220304150721.3802-3-tanureal@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Changes:
1. Revise rt5682s_sar_power_mode and rt5682s_headset_detect to be more
rational.
2. Manually set to the jack-unplugging state via rt5682s_headset_detect
during going to suspend. Close unnecessary powers and prepare for
re-detecting the CBJ during resuming.
3. Simplize rt5682s_resume.
Signed-off-by: Derek Fang <derek.fang@realtek.com>
Link: https://lore.kernel.org/r/20220307102154.26065-1-derek.fang@realtek.com
Signed-off-by: Mark Brown <broonie@kernel.org>
As the potential failure of the wm8350_register_irq(),
it should be better to check it and return error if fails.
Also, use 'free_' in order to avoid the same code.
Fixes: a6ba2b2dab ("ASoC: Implement WM8350 headphone jack detection")
Signed-off-by: Jiasheng Jiang <jiasheng@iscas.ac.cn>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20220304023821.391936-1-jiasheng@iscas.ac.cn
Signed-off-by: Mark Brown <broonie@kernel.org>
This node pointer is returned by of_parse_phandle() with refcount
incremented in this function.
Calling of_node_put() to avoid the refcount leak.
Fixes: 531f67e41d ("ASoC: at91sam9g20ek-wm8731: convert to dt support")
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Reviewed-by: Codrin Ciubotariu <codrin.ciubotariu@microchip.com>
Link: https://lore.kernel.org/r/20220307124539.1743-1-linmq006@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The "adata->i2s_irq" variable is unsigned so this error handling
code will not work.
Fixes: 87d71a1287 ("ASoC: amd: pcm-dma: Use platform_get_irq() to get the interrupt")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://lore.kernel.org/r/20220304131534.GD28739@kili
Signed-off-by: Mark Brown <broonie@kernel.org>
The "adata->pdm_irq" variable is unsigned so the error handling will
not work.
Fixes: 87d71a1287 ("ASoC: amd: pcm-dma: Use platform_get_irq() to get the interrupt")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://lore.kernel.org/r/20220304131335.GB28739@kili
Signed-off-by: Mark Brown <broonie@kernel.org>
The "adata->i2s_irq" is unsigned so this error handling will not
work.
Fixes: 3304a242f4 ("ASoC: amd: Use platform_get_irq_byname() to get the interrupt")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://lore.kernel.org/r/20220304131449.GC28739@kili
Signed-off-by: Mark Brown <broonie@kernel.org>
HP changed the DMI identification for 2022 devices:
Product Name: HP Spectre x360 Conv 13-ap0001na
Product Name: 8709
This patch relaxes the DMI_MATCH criterion to work with all versions of this product.
Reviewed-by: Rander Wang <rander.wang@intel.com>
Signed-off-by: Anthony I Gilea <i@cpp.in>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20220304204532.54675-4-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
We have eleven machine drivers who make explicit references to
gpios. Let's add the dependency.
The use of 'depends on' instead of 'select' is intentional. On one
side it could be argued that the GPIOs are required, but on the other
it might create more issues with randconfig builds. This patch sticks
with the existing direction of using 'depends' on high-level non-audio
dependencies
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Link: https://lore.kernel.org/r/20220304204532.54675-3-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch reverts commit 4262ddc2ad ("ASoC: Intel: boards: add
explicit dependency on GPIOLIB when DMIC is used") and all follow-up
additions of this dependency.
Now that the DMIC does not depend on GPIOLIB we can simplify again.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Link: https://lore.kernel.org/r/20220304204532.54675-2-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
With higher channel counts, we may need higher clock rates. Starting
with SAI v3.1 (i.MX8MM), we can bypass the divider and get a 1:1
bclk:mclk ratio. Add the necessary support.
Signed-off-by: Viorel Suman <viorel.suman@nxp.com>
Signed-off-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Link: https://lore.kernel.org/r/20220302083428.3804687-8-s.hauer@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
In fsl_sai_set_bclk() we want to calculate the divider that gets us
closest to the desired frequency, so use DIV_ROUND_CLOSEST() instead of
just doing a clk_rate/freq.
Also discard invalid ratios earlier.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Link: https://lore.kernel.org/r/20220302083428.3804687-7-s.hauer@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
"ret" is normally used as a variable name for return values. In
fsl_sai_set_bclk() it stores the difference between the desired rate and
the rate we can archieve, so rename it to "diff". Also rename "savesub"
to "bestdiff" as that stores the best difference we have found.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Link: https://lore.kernel.org/r/20220302083428.3804687-6-s.hauer@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
The driver tests for the hardware revision being newer than 3.1
with (sai->verid.major >= 3 && sai->verid.minor >= 1). The result
is obviously wrong for hardware revision 4.0. Fix this by storing
the full version in a single variable and comparing to that one.
No practical change at the moment as there is no 4.0 ip version
currently.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Link: https://lore.kernel.org/r/20220302083428.3804687-5-s.hauer@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Depending on SAI synchronization mode, the same value is either
written to FSL_SAI_TCR2 or FSL_SAI_RCR2 or nothing is written at all.
As the computation is the same either way, factor it out to make it
clearer what the difference is. No functional change.
Signed-off-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Link: https://lore.kernel.org/r/20220302083428.3804687-4-s.hauer@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Instead of using a boolean "irq_none" to describe the interrupt
handlers return value use a variable of type irqreturn_t and return
it directly. No functional change.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Link: https://lore.kernel.org/r/20220302083428.3804687-3-s.hauer@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
The fsl_sai driver has FSL_FMT_TRANSMITTER and FSL_FMT_RECEIVER defines
which are used in a single function only then are then only translated
into a bool 'tx' variable. Drop the defines and pass the boolean value
directly to fsl_sai_set_dai_sysclk_tr(). No functional change.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Link: https://lore.kernel.org/r/20220302083428.3804687-2-s.hauer@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
The Awinic AW8738 is a simple audio amplifier using a single GPIO.
The main difference to simple-amplifier is that there is a "one-wire
pulse control" that allows configuring the amplifier to one of a few
pre-defined modes. This can be used to configure the speaker-guard
function (primarily the power limit for the amplifier).
Add a simple driver that allows setting it up in the device tree
with a specified mode number.
Signed-off-by: Jonathan Albrieux <jonathan.albrieux@gmail.com>
Co-developed-by: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20220304102452.26856-3-stephan@gerhold.net
Signed-off-by: Mark Brown <broonie@kernel.org>
Some audio hardware cannot support the same slot width for all sample
widths, or a slot width equal to the sample width for all sample widths.
This is usually due either to limitations of the audio serial port or
system clocking restrictions.
A typical example would be:
- 16-bit samples in 16-bit slots
- 24-bit samples in 32-bit slots
The new dai-tdm-slot-width-map property allows setting a mapping of
sample widths and the corresponding tdm slot widths and slot counts.
Although the slot count is usually the same for all cases this does
allow for adding padding slots to maintain the same bitclk frequency.
The property is added to each endpoint node that needs the component
DAI to be told the TDM slot width and count.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20220228172754.453783-3-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Host is trying to acquire semaphore lock based on HW_SEM_RETRY_COUNT
value which is set to 10 by default. So host will loop for 10 times
trying to acquire lock before giving error msg "Failed to acquire HW
lock". Though this loop count of 10 is good enough with most of the
times but we have observed such failure msg in very few cases(~5 %).
Increase ACP_HW_SEM_RETRY_COUNT to avoid such issue and loop for a
significant time period before throwing error. We're setting newer
loop count to quite higher value of 10K but it's very unlikely that
it will loop for this count, since for most of the cases lock will
get acquired at much lesser loop iterations.
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Signed-off-by: Ajit Kumar Pandey <AjitKumar.Pandey@amd.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20220304205733.62233-8-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
We are using PTE_GRP1 for DMA operations to load firmware binaries
but we are enabling PTE_GRP and flushing ATU cache much before in
probe callbacks. This can cause issue if we try to load firmware
runtime during system resume as probe callback will not be invoked
hence PTE_GRP will not be enabled. Moreover it makes more sense to
flush the cache after register configuration.
Move PTE group register configuration to acp-loader within pre_fw_run
callback to avoid such issue.
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Signed-off-by: Ajit Kumar Pandey <AjitKumar.Pandey@amd.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20220304205733.62233-7-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add lock and unlock around ipc irq handling code using hw semaphore
register that exhibit special property for register read calls. As
host and DSP firmware uses few shared registers, there is a possible
race condition around those shared registers values. This lock ensure
synchronization between Firmware and host ipc interrupts.
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Signed-off-by: Ajit Kumar Pandey <AjitKumar.Pandey@amd.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20220304205733.62233-6-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
ACP_SRAM_PTE block has cache that needs to be flushed after every
PTE updates. This patch updates ACPAXI2AXI_ATU_CTRL register to
flush cache after updating PTE with stream physical address.
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Signed-off-by: Ajit Kumar Pandey <AjitKumar.Pandey@amd.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20220304205733.62233-5-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The ipc_pcm_params() ops implementation for AMD is a NOP and since the
callback is marked now as optional, it can be dropped along with the
empty function.
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Reviewed-by: Daniel Baluta <daniel.baluta@nxp.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20220304205733.62233-4-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Instead of using the values from ipc_params, take them directly from
substream->runtime.
This is in preparation of making the platform hw_params callback to be
IPC agnostic.
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Reviewed-by: Daniel Baluta <daniel.baluta@nxp.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20220304205733.62233-3-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add PCI DID for Intel Raptor Lake S.
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Signed-off-by: Gongjun Song <gongjun.song@intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20220304205733.62233-2-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch fix the second dai driver's dai widget can't connect to the
endpoint. Because "bt-sco-pcm" and "bt-sco-pcm-wb" dai driver have the
same stream_name, so it will cause they have the same widget name.
Therefor it will just create only one route when do snd_soc_dapm_add_route
that only find the widget through the widget name.
Signed-off-by: Jiaxin Yu <jiaxin.yu@mediatek.com>
Link: https://lore.kernel.org/r/20220302013533.29068-1-jiaxin.yu@mediatek.com
Signed-off-by: Mark Brown <broonie@kernel.org>
pcm name can be "Analog" and "Alt Analog", cpcm->name can be
"Analog Codec DAI" and "Alt Analog Codec DAI". When pcm_name
is "Analog", "Analog Codec DAI" and "Alt Analog Codec DAI" are
both satisfy the 'if (strstr(cpcm->name, pcm_name))' condition,
which may cause the returned cpcm to be "Alt Analog Codec DAI".
Even if we get the pcm name by id, and "Analog Codec DAI" goes
into the loop before "Alt Analog Codec DAI", but I still think
we'd better have multiple insurances against unexpected return
values. After, we can correctly return the expected result
even if other relevant places are changed.
Signed-off-by: Meng Tang <tangmeng@uniontech.com>
Link: https://lore.kernel.org/r/20220302094351.3487-1-tangmeng@uniontech.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Merge series from Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>:
Two cleanups to remove an unused filename and typos, and one addition
of an ACPI matching table for a Dell SoundWire SKU without local
microphones.
The main change is the addition of a common 'sof-ssp-amp' machine
driver for devices with amplifiers only (no headset codec) and
different connections using I2S links (Bluetooth offload, HDMI
receiver). It's likely that the amplifier will be swapped out by OEMs,
this machine driver provides a relatively generic solution to avoid
copy-paste of similar solutions.
The copy_to/from_user() functions return the number of bytes remaining
to be copied. This function needs to return negative error codes
because snd_soc_pcm_component_copy_user() treats positive returns as
success in soc_component_ret().
Fixes: 7d7209557b ("ASoC: qcom: Add support for codec dma driver")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://lore.kernel.org/r/20220301081104.GB17375@kili
Signed-off-by: Mark Brown <broonie@kernel.org>
There is one call trace that snd_soc_register_card()
->snd_soc_bind_card()->soc_init_pcm_runtime()
->snd_soc_dai_compress_new()->snd_soc_new_compress().
In the trace the 'codec_dai' transfers from card->dai_link,
and we can see from the snd_soc_add_pcm_runtime() in
snd_soc_bind_card() that, if value of card->dai_link->num_codecs
is 0, then 'codec_dai' could be null pointer caused
by index out of bound in 'asoc_rtd_to_codec(rtd, 0)'.
And snd_soc_register_card() is called by various platforms.
Therefore, it is better to add the check in the case of misusing.
And because 'cpu_dai' has already checked in soc_init_pcm_runtime(),
there is no need to check again.
Adding the check as follow, then if 'codec_dai' is null,
snd_soc_new_compress() will not pass through the check
'if (playback + capture != 1)', avoiding the leftover use of
'codec_dai'.
Fixes: 467fece ("ASoC: soc-dai: move snd_soc_dai_stream_valid() to soc-dai.c")
Signed-off-by: Jiasheng Jiang <jiasheng@iscas.ac.cn>
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://lore.kernel.org/r/1634285633-529368-1-git-send-email-jiasheng@iscas.ac.cn
Signed-off-by: Mark Brown <broonie@kernel.org>
In dmaengine_pcm_set_runtime_hwparams() period_bytes_min is hardcoded to
256. For some applications that may be too big. This patch changes that
to calculate the value based on dma_data->maxburst. The correct value
would be maxburst multiplied by the address width of the hardware FIFO.
Unfortunately the address width is dynamically calculated based on the
stream parameters and is not known at open time, so the worst case
is chosen here which is 8 bytes, the maximum that is supported by
dmaengine drivers.
Not all drivers may set a maxburst value, so we fall back to the
previously used hardcoded value of 256 bytes.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Link: https://lore.kernel.org/r/20220301113446.1053171-1-s.hauer@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
As the potential failure of the clk_enable(),
it should be better to check it, as same as clk_prepare_enable().
Fixes: c9afc1834e ("ASoC: dwc: Disallow building designware_pcm as a module")
Signed-off-by: Jiasheng Jiang <jiasheng@iscas.ac.cn>
Link: https://lore.kernel.org/r/20220301084742.3751939-1-jiasheng@iscas.ac.cn
Signed-off-by: Mark Brown <broonie@kernel.org>
As the potential failure of the clk_enable(),
it should be better to check it and return error if fals.
Fixes: cbaadf0f90 ("ASoC: atmel_ssc_dai: refactor the startup and shutdown")
Signed-off-by: Jiasheng Jiang <jiasheng@iscas.ac.cn>
Link: https://lore.kernel.org/r/20220301090637.3776558-1-jiasheng@iscas.ac.cn
Signed-off-by: Mark Brown <broonie@kernel.org>
As the potential failure of the clk_enable(),
it should be better to check it, like mxs_saif_trigger().
Fixes: d0ba4c0149 ("ASoC: mxs-saif: set a base clock rate for EXTMASTER mode work")
Signed-off-by: Jiasheng Jiang <jiasheng@iscas.ac.cn>
Link: https://lore.kernel.org/r/20220301081717.3727190-1-jiasheng@iscas.ac.cn
Signed-off-by: Mark Brown <broonie@kernel.org>
