Add a bool in ath9k_platform_data to pass AHB clock speed information.
Driver needs this to configure PLL on some SOCs.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The default maximum transmit length for NCM USB frames should be so
that a short packet happens at the end if the device supports a length
greater than the defined maximum. This is achieved by adding 4 bytes
to the maximum length so that the existing logic can fit a short
packet there.
Signed-off-by: Hans Petter Selasky <hselasky@c2i.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The firmware is cached during the first successfull call to open() and
released once the network device is unregistered. The driver uses the
cached firmware between open() and unregister_netdev().
So far the firmware is optional : a failure to load the firmware does
not prevent open() to success. It is thus necessary to 1) unregister
all 816x / 810[23] devices and 2) force a driver probe to issue a new
firmware load.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Fixed-by: Ciprian Docan <docan@eden.rutgers.edu>
Cc: Realtek linux nic maintainers <nic_swsd@realtek.com>
Fixed packets parameters for FW in UDP checksum offload flow.
Do not dereference TCP headers on non TCP frames.
Reported-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A deadlock was reported to me recently that occured when netconsole was being
used in a virtual guest. If the virtio_net driver was removed while netconsole
was setup to use an interface that was driven by that driver, the guest
deadlocked. No backtrace was provided because netconsole was the only console
configured, but it became clear pretty quickly what the problem was. In
netconsole_netdev_event, if we get an unregister event, we call
__netpoll_cleanup with the target_list_lock held and irqs disabled.
__netpoll_cleanup can, if pending netpoll packets are waiting call
cancel_delayed_work_sync, which is a sleeping path. the might_sleep call in
that path gets triggered, causing a console warning to be issued. The
netconsole write handler of course tries to take the target_list_lock again,
which we already hold, causing deadlock.
The fix is pretty striaghtforward. Simply drop the target_list_lock and
re-enable irqs prior to calling __netpoll_cleanup, the re-acquire the lock, and
restart the loop. Confirmed by myself to fix the problem reported.
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
CC: "David S. Miller" <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This variable is only ever checked right after
the function that sets it, but the same function
will also return the status, so we can pass it
through instead of checking hw_ready later.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
On new hardware, ucode images always come in
pairs: code and data. Therefore, combine the
variables into an appropriate struct and use
that when both code and data are needed.
Also, combine allocation and copying so that
we have less code in total.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
The current firmware loading mechanism in
iwlwifi is very hard to follow, and thus
hard to maintain. To make it easier, make
the firmware loading synchronous.
For now, as a side effect, this removes a
number of retry possibilities we had. It
isn't typical for this to fail, but if it
does happen we restart from scratch which
this also makes easier to do should it be
necessary.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
When the firmware encounters an error while the
driver is waiting for a notification, it will
never get that notification. Therefore, instead
of timing out, bail out on errors when waiting
for notifications.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
We're unlikely to care about the actual time spent
waiting, so make the function return an error code
which is less error prone in coding new uses.
Also, while at it, mark __must_check.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
A notification wait function is called with the
command, but currently has no way of passing
data back to the caller -- fix that by adding a
void pointer to the function that can be used
between the caller and the function.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Starting the device consists of many things,
refactor out enabling the hardware and also
return -ERFKILL when the rfkill signal is
found to be asserted (which makes more sense
anyway, but is also required now to make the
__iwl_up function return right away.)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
The iwl_down path really consists of multiple things,
refactor out the hardware resetting (including, of
course, related software state like irqs).
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
There's no point in running through iwl_down()
when we never registered with mac80211, as it
just cleans up internal structures that were
never initialised in this case. Therefore we
can also remove the special handling for this
case from __iwl_down().
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
The current code to read the error table header
just hardcodes all the offsets, which is a bit
hard to understand. We can read in the entire
header (as much as we need) into a structure,
and then take the data from there, which makes
it easier to understand. To read a bigger blob
we also don't need to grab NIC access for each
word read, making the code more efficient.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
The mechanism used to initiate work events from the interrupt
handler has a classic read/modify/write race between the interrupt
handler that sets the condition, and the worker task that reads and
clears the condition. Close these races by using atomic
bit fields.
Cc: stable@kernel.org
Cc: Jie Yang <jie.yang@atheros.com>
Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The commit 609ff3b ("be2net: add code to display temperature of ASIC")
adds support to display temperature of ASIC but there is missing
increment of work_counter in be_worker. Because of this 1) the
function be_cmd_get_die_temperature is called every 1 second instead
of every 32 seconds 2) be_cmd_get_die_temperature is called, although
it is not supported. This patch fixes this bug.
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds link messages and an item to the sign-on banner to make
EEE status more visible.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A common AUX CTRL operation in the driver is to enable and disable the
SMDSP. This patch consolidates the code so that the details of the
operation are in one place. This patch also adds code to make sure the
SMDSP is enabled before executing code that relies on it.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a write accessor for the aux ctrl phy register.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a read accessor for the aux ctrl register.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Phy accessor functions should live closer to where the base phy read /
write routines are.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When tg3 was new, phy accesses through ioctl were allowable at any time.
Then, the driver started shutting down the phy when the device was
closed. Phy accesses would be allowed when the driver first attached to
the device, but then would be forbidden after the device had been up'd
and down'd. After that, management firmware made it illegal to access
the phy unless the driver "owned" the device. Now that most firmware
is being moved over to the APE, it is less clear when phy accesses are
safe.
While it is possible to attempt to identify these conditions and code
the driver to navigate through the pitfalls, it could be perplexing to
the admin why phy accesses work in some cases and not others. This
patch brings some uniformity to the problem by only allowing phy
accesses while the driver has control of the device.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The loopback test assumes all traffic goes to the first rx queue. There
is a 1 in 4 chance this won't be true if RSS is enabled though. This
patch reprograms the RSS indirection table to route all rx packets to
the first queue.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The oldest tg3 devices had large rx producer ring BD caches. Back then,
it made sense to make the BD cache replenish threshold only a function
of the number of rx buffers posted by the driver. Since then, the BD
cache sizes have shrunk to 25% of their original size and, in some
cases, the ring sizes have quadrupled in size. Under such conditions,
static BD cache replenish thresholds no longer match the hardware
constraints.
This patch attempts to factor in the BD cache size into the bd cache
replenish strategy, taking the existing hardware bugs into account.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 5717, 5718, 5719 A0, and 5720 A0 has a bug where the rx_discards
statistic counter will increment when dropping unwanted multicast
frames. This patch works around the problem by attempting to
recreate the data using other means. The resulting value will not be
accurate, but it can still serve as a problem indicator.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
mac-fec.c was setting individual UDP address registers instead of multicast
group address registers when joining a multicast group.
This prevented from correctly receiving UDP multicast packets.
According to datasheet, replaced hash_table_high and hash_table_low
with grp_hash_table_high and grp_hash_table_low respectively.
Also renamed hash_table_* with grp_hash_table_* in struct fec declaration
for 8xx: these registers are used only for multicast there.
Tested on a MPC5121 based board.
Build tested also against mpc866_ads_defconfig.
Signed-off-by: Andrea Galbusera <gizero@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
From Stephen Rothwell:
--------------------
After merging the final tree, today's linux-next build (powerpc chrp32_defconfig)
failed like this:
drivers/net/mv643xx_eth.c: In function 'port_start':
drivers/net/mv643xx_eth.c:2250: error: 'dev' undeclared (first use in this function)
Caused by commit aad59c431b ("net: mv643xx: convert to hw_features").
--------------------
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since
commit a120e912eb
Author: Stanislaw Gruszka <sgruszka@redhat.com>
Date: Fri Feb 19 15:47:33 2010 -0800
iwlwifi: sanity check before counting number of tfds can be free
we use skb->data after calling ieee80211_tx_status_irqsafe(), which
could free skb instantly.
On current kernels I do not observe practical problems related with
bug, but on 2.6.35.y it cause random system hangs when stressing
wireless link, making bisection of other problems impossible.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since
commit a120e912eb
Author: Stanislaw Gruszka <sgruszka@redhat.com>
Date: Fri Feb 19 15:47:33 2010 -0800
iwlwifi: sanity check before counting number of tfds can be free
we use skb->data after calling ieee80211_tx_status_irqsafe(), which
could free skb instantly.
On current kernels I do not observe practical problems related with
bug, but on 2.6.35.y it cause random system hangs when stressing
wireless link.
Cc: stable@kernel.org # 2.6.32+
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The slave member of struct aggregator does not necessarily point
to a slave which is part of the aggregator. It points to the
slave structure containing the aggregator structure, while
completely different slaves (or no slaves at all) may be part of
the aggregator.
The agg_device_up() function wrongly uses agg->slave to find the state
of the aggregator. Use agg->lag_ports->slave instead. The bug has
been introduced by commit 4cd6fe1c64
("bonding: fix link down handling in 802.3ad mode").
Signed-off-by: Jiri Bohac <jbohac@suse.cz>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We are currently continuing if ehea_restart_qps() fails, when we
do a memory DLPAR (remove or add more memory to the system).
This patch just let the NAPI disabled if the ehea_restart_qps()
fails.
Signed-off-by: Breno Leitao <leitao@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This changes offload setting behaviour to what I think is correct:
- offloads set via ethtool mean what admin wants to use (by default
he wants 'em all)
- offloads set via ioctl() mean what userspace is expecting to get
(this limits which admin wishes are granted)
- TUN_NOCHECKSUM is ignored, as it might cause broken packets when
forwarded (ip_summed == CHECKSUM_UNNECESSARY means that checksum
was verified, not that it can be ignored)
If TUN_NOCHECKSUM is implemented, it should set skb->csum_* and
skb->ip_summed (= CHECKSUM_PARTIAL) for known protocols and let others
be verified by kernel when necessary.
TUN_NOCHECKSUM handling was introduced by commit
f43798c276:
tun: Allow GSO using virtio_net_hdr
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Acked-by: Ian Campbell <ian.campbell@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bit more than minimal conversion. There might be some issues because
of qlcnic_set_netdev_features() if it's called after netdev init.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
A minimal conversion.
ibmveth_set_csum_offload() can be folded into ibmveth_set_features()
and adapter->rx_csum removed - left for later cleanup.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
This also fixes bug in xmit path, where TX checksum offload state was used
instead of skb->ip_summed to decide if the offload was needed.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change will allow the default value of tx rate to be displayed
when ip link show is called on a PF interface.
Signed-off-by: Ajit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
eth_get_statistics and vlan_config command have same opcode.
Use opcode subsystem id to differentiate one from other.
Signed-off-by: Ajit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the below compile warning:
drivers/net/bna/bfa_ioc.c:1922: warning: ‘bfa_ioc_smem_pgoff’ defined but not used
Signed-off-by: Shan Wei <shanwei@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the below compile warning:
drivers/net/forcedeth.c:4266: warning: ‘nv_set_tso’ defined but not used
commit 569e146 converts forcedeth driver to use hw_features.
So, implement function of .set_tso is abandoned.
Signed-off-by: Shan Wei <shanwei@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement the get_antenna and set_antenna callback functions, which will
allow clients to control the antenna for all non-11n hardware (Antenna handling
in rt2800 is still a bit magical, so we can't use the set_antenna for those drivers
yet).
To best support the set_antenna callback some modifications are needed in the
diversity handling. We should never look at the default antenna settings to determine
if software diversity is enabled. Instead we should set the diversity flag when
possible, which will allow the link_tuner to automatically pick up the tuning.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
With the get_ringparam callback function we can export ring parameters
to ethtool through the mac80211 interface.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
All register reads/writes in rt2800usb were previously done with
rt2800_register_read/rt2800_register_write. These however indirectly
call rt2x00usb_register_read/rt2x00usb_register_write which adds an
additional overhead of at least one call and several move instructions
to each register access.
Replacing the calls to rt2800_register_read/rt2800_register_write with
direct calls to rt2x00usb_register_read/rt2x00usb_register_write gets
rid of quite a number of instructions in the drivers hotpaths (IRQ
handling and txdone handling).
For consistency replace all references to rt2800_register_read/write
with the rt2x00usb_register_read/write variants.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
All register reads/writes in rt2800pci were previously done with
rt2800_register_read/rt2800_register_write. These however indirectly
call rt2x00pci_register_read/rt2x00pci_register_write which adds an
additional overhead of at least one call and several move instructions
to each register access.
Replacing the calls to rt2800_register_read/rt2800_register_write with
direct calls to rt2x00pci_register_read/rt2x00pci_register_write gets
rid of quite a number of instructions in the drivers hotpaths (IRQ
handling and txdone handling).
For consistency replace all references to rt2800_register_read/write
with the rt2x00pci_register_read/write variants.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The two functions that are in rt2x00ht.c can be much better placed
closer to the places where the call-sites of these functions are (one
in rt2x00config.c and one in rt2x00queue.c) allowing us to make these
functions static.
Also, conditional compilations doesn't seem to be necessary anymore as
802.11n support is quite common nowadays.
This makes the code a bit easier readable and searchable.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Code seems to be feature-complete, so no reason to not enable
these devices by default.
Also, remove the sentence about the support for these devices being
non-functional.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The rt33xx devices support for both PCI and USB devices has been in
the tree for a couple of months now, and seems to be functional and
not in a worse shape than the support for rt28xx and rt30xx devices.
No longer mark it as experimental and enable the support for these
devices by default.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add USB IDs that are listed in the latest Ralink Windows and/or Linux drivers.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Both USB and PCI drivers allow a system administrator to dynamically add
USB/PCI IDs to the device table that a driver supports via the
/sys/bus/{usb,pci,pci_express}/drivers/<driver-name>/new_id files.
However, for the rt2x00 drivers using this method currently crashes the
system with a NULL pointer failure.
This is due to the set-up of rt2x00 where the probe functions require a
rt2x00_ops structure in the driver_info field of the probed device. As
this field is empty for the dynamically added devices this fails for
these devices.
Fix this by introducing driver-specific probe wrappers that do nothing
but calling the bus-specific probe functions with the rt2x00_ops structure
as an argument, rather than depending on the driver_info field.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Move the USB ID entry from the unknown devices to the list of RT35xx based
devices.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This allows the compiler to perform the necessary bitfield calculations
during compile time instead of run time and thus reduces the number of
instructions to run during each tasklet invocation. This should improve
performance in the RX hotpath.
This comes at the cost of a slight increase in the module size (for
example rt2800pci):
Before:
text data bss dec hex filename
14133 832 4 14969 3a79 drivers/net/wireless/rt2x00/rt2800pci.ko
After:
text data bss dec hex filename
14149 832 4 14985 3a89 drivers/net/wireless/rt2x00/rt2800pci.ko
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When powersaving is enabled, assocaition times are very high
(for WPA2 networks, the time can easily be around the 3 seconds).
This is caused, because the flushing of the queues takes
too much time. Without the flushing callback mac80211 assumes
a timeout of 100ms while scanning. Limit all flush waiting
loops to the same maximum.
We can apply this maximum by passing the drop status to the
driver, which makes sure the driver performs extra actions
during the waiting for the queue to become empty.
After these changes, association times fall within the
healthy range of ~0.6 seconds with powersaving enabled.
The difference between association time between powersaving
enabled and disabled is now only ~0.1 second (which can also
be due to the measuring method).
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
TX status is reported by the hardware when a packet has been
sent (or after TX failed after possible retries), which is some
time after the DMA completion. Since the rt2800usb hardware can
not signal interrupts we have to use a timer, otherwise the
TX status would only be read by the next packet's TX DMA
completion, or by the watchdog thread.
Signed-off-by: Johannes Stezenbach <js@sig21.net>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The watchdog just triggers rt2800usb_work_txdone() when it
detects a TX status timeout, thus rt2800usb_work_txdone() needs to
handle this case.
Signed-off-by: Johannes Stezenbach <js@sig21.net>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add a timestamp to each queue entry which is updated whenever
the status of the entry changes, and remove the per-queue
timestamps. The previous check was incorrect and caused both
false positives and false negatives.
With the corrected check it comes apparent that the TX status
usually times out on rt2800usb unless there is sufficient traffic
(i.e. the next TX will complete the previous TX status).
Signed-off-by: Johannes Stezenbach <js@sig21.net>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Trying to fix the "TX status report missed" warnings
by reading the TX_STA_FIFO entries as quickly as possible.
The TX_STA_FIFO is too small in hardware, thus reading
it only from the workqueue is too slow and entries get lost.
Start an asynchronous read of the TX_STA_FIFO directly from
the TX URB completion callback (atomic context, thus it cannot
use the blocking rt2800_register_read()). If the async
read returns a valid FIFO entry, it is pushed into a larger
FIFO inside struct rt2x00_dev, until rt2800_txdone() picks
it up.
A .tx_dma_done callback is added to struct rt2x00lib_ops
to trigger the async read from the URB completion callback.
Signed-off-by: Johannes Stezenbach <js@sig21.net>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use TXOP_HTTXOP for beacons to stay in sync with the legacy drivers.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Bring the TX_SW_CFG2 initialisation for rt305x devices in sync with the
ralink legacy drivers.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This seems to fix problems with some powersaving clients since a
positive value in TBTT_SYNC_CFG_TBTT_ADJUST introduces beacon skew,
which is not wanted in AP mode.
Also update the rest of the TBTT_SYNC config according to the
legacy drivers in AP mode.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Allow passing a void pointer to rt2x00_queue_entry_for_each which in
turn in provided to the callback function.
Furthermore, allow the callback function to stop processing by returning
true. And also notify the caller of rt2x00_queue_entry_for_each if the
loop was canceled by the callback.
No functional changes, just preparation for an upcoming patch.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The number of flags defined for the rt2x00dev->flags field,
has been growing over the years. Currently we are approaching
the maximum number of bits which are available in the field.
A secondary problem, is that one part of the field are initialized only
during boot, because the driver requirements are initialized or device
requirements are loaded from the EEPROM. In both cases, the flags are
fixed and will not change during device operation. The other flags are
the device state, and will change frequently. So far this resulted in the fact
that for some flags, the atomic bit accessors are used, while for the others
the non-atomic variants are used.
By splitting the flags up into a "flags" and "cap_flags" we can put all flags
which are fixed inside "cap_flags". This field can then be read non-atomically.
In the "flags" field we keep the device state, which is going to be read atomically.
This adds more room for more flags in the future, and sanitizes the field access methods.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since commit 0b7fde54f9 "rt2x00: Protect
queue control with mutex" rt2x00 used rt2x00queue_pause_queue for
stopping a tx queue in mac80211. But in case of a failure in the tx
path rt2x00 still called ieee80211_stop_queue which stopped the queue
but prevented rt2x00queue_unpause_queue to wake the queue up again
resulting in a stuck tx queue.
Fix this by also using rt2x00queue_pause_queue in case of tx failures.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds WLAN LED support to the mac80211 rt2x00 driver for
Ralink SoC (rt305x) devices. The current WLAN LED drivers in
rt2800lib.c set the LED brightness via an MCU request, but do nothing
for SoC. This patch checks for SoC and sets the register to enable the
WLAN LED (instead of an MCU request). This enables the WLAN LED for
RT305x devices.
Signed-off-by: Layne Edwards <ledwards@astrumtech.net>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Frame filtering relies on having a valid destination index (keycache slot),
to keep track of the destination. Assigning a keycache slot (configured
to unencrypted, with no key data attached) improves powersave handling in
AP mode with no encryption.
The dummy keycache entry for a station is cleared, when a real key gets
added.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes a long standing issue of pending packets in the queue being
sent (and retransmitted many times) to sleeping stations.
This was made worse by aggregation through driver-internal retransmitting
of A-MDPU subframes.
Previously the hardware tx filter was cleared unconditionally for every
single packet - with this patch it uses the IEEE80211_TX_CTL_CLEAR_PS_FILT
for unaggregated frames.
A sta_notify driver op is added to stop aggregation for stations when they
enter powersave mode. Subframes stay buffered inside the driver, to ensure
that the BlockAck window keeps a sane state.
Since the driver uses software aggregation, the clearing of the tx filter
needs to be handled by the driver instead of mac80211 for aggregated frames.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
While leaving the oper channel, beacon generation is stopped
by mac80211 and beacon slots are marked as inactive.
During the scan, ath9k configures beacon timers
based on IEEE80211_CONF_OFFCHANNEL which inturn generates
beacon alert even though bslot is inactive.
ath9k fails to disable beacon alert while moving to offchannel
if none of the beacon slot is active. This is causing beacon
transmission on foreign channel. This patch enables swba
based on active bslots.
This issue was reported with two vifs (AP+STA) and triggered
scan in STA vif in unassociated state.
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ath9k_htc_tx_get_slot can return zero as valid index.
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Acked-by: Sujith Manoharan <Sujith.Manoharan@Atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
1) removal of unnecessary mwifiex_device structure
2) avoid passing adapter pointer to mwifiex_init_sw()
3) remove local variable drv_mode_info in mwifiex_add_card()
4) type change in mwifiex_bss_attr to match mwifiex_private
5) removal of more wordy comments
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
use corresponding macros defined in include/linux/ieee80211.h
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove some local variables (mainly function return values)
that are used only once. Also, one dummy function and some
wordy comments are removed.
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: Kiran Divekar <dkiran@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Commit be663ab670 (iwlwifi: split the drivers for
agn and legacy devices 3945/4965) added code to read the 4965's revision ID from
the PCI configuration register while it's already stored by PCI subsystem in the
'revision' field of 'struct pci_dev'...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Move the ath9k_htc debugfs under ieee80211 to be inline
with ath9k driver and it also helps to simplify debug code.
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Acked-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The 0x6C regulatory domain is just like the 0x6A regulatory
domain but differs in that 0x6C will allow adhoc and active
scan on its channels only if we are associated to an AP
with a country IE that allows those channels. The
ath_reg_apply_beaconing_flags() does just this -- we respect
the manufacturer's intent on only enabling beaconing modes
of operation if and only if blessed by the country IE.
Cc: David Quan <david.quan@atheros.com>
Cc: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The patch 'ath9k_hw: fix stopping rx DMA during resets' added code to detect
a condition where rx DMA was stopped, but the MAC failed to enter the idle
state. This condition requires a hardware reset, however the return value
of ath_stoprecv was 'true' in that case, which allowed it to skip the reset
when issuing a fast channel change.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Reported-by: Paul Stewart <pstew@google.com>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix sparse warning:
CHECK drivers/net/wireless/wl12xx/main.c
drivers/net/wireless/wl12xx/main.c:1246:17: warning: symbol 'wl12xx_alloc_dummy_packet' was not declared. Should it be static?
Signed-off-by: Luciano Coelho <coelho@ti.com>
Instead of hardcoding the hci_io_ds configuration that we write to the
SDIO_IO_DS top registed, read it from the default configuration so
that it's easier to change for different platforms.
Reported-by: Ido Yariv <ido@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Some platforms are incapable of triggering on level interrupts. Add a
platform quirks member in the platform data structure, as well as an
edge interrupt quirk which can be set on such platforms.
When the interrupt is requested with IRQF_TRIGGER_RISING, IRQF_ONESHOT
cannot be used, as we might miss interrupts that occur after the FW
status is cleared and before the threaded interrupt handler exits.
Moreover, when IRQF_ONESHOT is not set, iterating more than once in the
threaded interrupt handler introduces a few race conditions between this
handler and the hardirq handler. Currently this is worked around by
limiting the loop to one iteration only. This workaround has an impact
on performance. To remove to this restriction, the race conditions will
need to be addressed.
Signed-off-by: Ido Yariv <ido@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
The total number of TX memory blocks may change when the dynamic memory
option is enabled. The current implementation only tracks the available
memory blocks, which over-complicates TX blocks accounting.
By tracking the number of allocated blocks, calculation of the number of
available blocks becomes simpler and cleaner. It simply equals the total
number of TX memory blocks minus the allocated ones.
Also, remove some unnecessary castings and use union member accesses
instead.
Signed-off-by: Ido Yariv <ido@wizery.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
The current implementation allocates a skb each time one is requested by
the firmware. Since dummy packets are handled differently than regular
packets, the skb needs to be marked. Currently, this is done by
setting the pkt_type member to 5. This might not be safe, as we cannot
be sure that there won't be any other packets with this pkt_type value.
Since the packet does not change from one request to another, we can
simply allocate a dummy packet template and always send it. All changes
to the skb done during packet preparation must be reverted, so the same
skb can be reused.
The dummy packets are not transmitted, therefore there's no need to set
the BSSID or our own MAC address.
In addition, the header portion of the packet was zeroed by mistake, so
fix that as well.
Signed-off-by: Ido Yariv <ido@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Simplify and clean up the block size alignment code:
1. Set the block size according to the padding field type, as it cannot
exceed the maximum value this field can hold.
2. Move the alignment code into a function instead of duplicating it in
multiple places.
3. In the current implementation, the block_size member can be
misleading because a zero value actually means that there's no need to
align. Declare a block size alignment quirk instead.
Signed-off-by: Ido Yariv <ido@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Clean up the boot sequence code & fix the following issues:
1. Always read the registers' values and set the relevant bits instead of
zeroing all other bits
2. Handle cases where wl1271_top_reg_read returns an error
3. Verify that the HW can detect the selected clock source
4. Remove 128x PG10 initialization code
5. Configure the MCS PLL to work in HP mode
Signed-off-by: Ido Yariv <ido@wizery.com>
Reviewed-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Issuing multiple JOIN commands to the wl12xx's firmware, while
we're associated, might have undesired implications, so the driver
prints a message when that happens, and warn developers who check
out the source.
Update the commentary in order to consider the one valid scenario
where this can happen: roaming.
Cautiously keep the message for now, until we either gain confidence
there are no unintentional JOIN-while-associated events, or until
we move to the new multi-role fw who solves this multiple-join issue
for good.
Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
The wl12xx device normally drops all frames coming from BSSID
it is not joined with.
This behavior is configured today by the wl12xx driver in response
to a handful of ieee80211_bss_change and ieee80211_conf_changed
notification flags, such as BSS_CHANGED_ASSOC, BSS_CHANGED_BSSID,
IEEE80211_CONF_CHANGE_IDLE, etc..
This breaks when we roam to a new BSSID, where authentication frames
are sent before any BSS_CHANGED/CONF_CHANGED flags are received.
When this happens the hardware silently drops the authentication
responses, and the roaming fails.
Ideally this aggressive filtering behavior of the device should be disabled
upon a notification from mac80211. Such notification will take place
after multi-channel support will be added: mac80211 will likely send a
remain-on-channel notification to drivers when entering sensitive
states (like authentication), otherwise the firmware might jump to
different channels (to serve a different role).
Until those notifications materialize, disable the hw BSSID filter
when authentication requests are sent, so roaming would work.
Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
Reviewed-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Because of the hardware recovery mechanism, its possible the
__wl1271_op_remove_interface is called twice. Currently, this leads to a
kernel crash even before a kernel WARNing can be issued.
Fix this.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
ELP (Extremely/Enhanced Low Power, or something like that ;)) refers to
the powerstate of the 12xx chip, in which very low power is consumed,
and no commands (from the host) can be issued until the chip is woken up.
Wakeup/sleep commands must be protected by a wl->mutex, so it's generally
a good idea to call wakeup/sleep along with the mutex lock/unlock (where
needed). However, in some places the wl12xx driver calls wakeup/sleep in
some "inner" functions. This result in some "nested" wakeup/sleep calls
which might end up letting the chip go to sleep prematurely (e.g. during
event handling).
Fix it by rearranging the elp calls to come along with mutex_lock/unlock.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Ido Yariv <ido@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Initialize the channel and band from mac80211 conf even when the FW is
not yet loaded. This mitigates a bug in AP-mode where the channel was
never changed from its initial setting after FW boot and was therefore
never configured to FW.
Reported-by: Alexander Boukaty <alexanderb@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
We were using an array of booleans to mark the channels we had already
scanned. This was causing a sparse error, because bool is not a type
with defined size. To fix this, use bitmasks instead, which is much
cleaner anyway.
Thanks Johannes Berg for the idea.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Fix the following sparse warnings:
drivers/net/wireless/wl12xx/main.c:1129:5: warning: symbol '__wl1271_plt_stop' was not declared. Should it be static?
drivers/net/wireless/wl12xx/main.c:2988:5: warning: symbol 'wl1271_op_ampdu_action' was not declared. Should it be static?
Both functions should be static.
Signed-off-by: Luciano Coelho <coelho@ti.com>
The Soft Gemini BT load ratio value has changed its meaning with FW
version 6.1.0.0.310. It now means the passive scan compensation
percentage during A2DP EDR. Instead of 50, we need to use 200.
Fix the SG configuration accordingly.
Signed-off-by: Luciano Coelho <coelho@ti.com>
The firmware requires dummy packets to be sent using TID 7
(WL1271_TID_MGMT). Instead of hardcoding it in the tx_fill_hdr()
function, set it when creating the packet itself.
This requires Eliad's fix to set the actual TID in the TX descriptor.
Cc: Ido Yariv <ido@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
When passing a tx frame, the driver incorrectly set desc->tid
with the ac instead of the actual tid.
It has some serious implications when using 802.11n + QoS,
as the fw starts a BlockAck with the wrong tid (which finally
cause beacon loss and disconnection / some fw crash)
Fix it by using the actual tid stored in skb->priority.
Reported-by: Shahar Levi <shahar_levi@ti.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
The interface list maintained in main.c is not mutex protected. This could
cause issues, as the list is accessed from notifier chains.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
On wl128x based devices, when TX packets are aggregated, each packet
size must be aligned to the SDIO block size, and sent using block mode
transfers.
The block size is set to 256 bytes, which is less than the maximum
possible byte transfer. Thus, if two small packets (< 256 bytes) are
aggregated, the aggregation buffer size would be 512, and will be sent
using byte mode transfers. This can have undesired side effects.
Fix this by setting the MMC_QUIRK_BLKSZ_FOR_BYTE_MODE mmc card quirk.
For 127x chips this has no effect, as the block size is set to 512
bytes.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Ido Yariv <ido@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Allow early termination of 50 consecutive beacons.
This value is the recommended one by the 12xx's system/RF team,
and tests show that power consumption is improved as expected.
Reported-by: Ruthy Zaphir <ruthyz@ti.com>
Tested-by: Danil Shalumov <danils@ti.com>
Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
The wl12xx chip supports one Rx STBC spatial stream. Announce this in
the HT capabilities info field.
Signed-off-by: Shahar Levi <shahar_levi@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
The rx-status passed to mac80211 along with each received frame contains the
band on which the frame was received. Under certain circumstances, this band
information may be incorrect, causing in worst case a WARNING from mac80211,
and causes the received frame to be dropped.
This scenario mainly occurs when performing connected-mode scans, when the
received scan results are from the other band than the one currently
associated to.
[Since desc_band doesn't exist anymore, use status->band in the later
call to ieee80211_channel_to_frequency() to fix compilation -- Luca]
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
All the new firmware versions (>=6.1.3.50.58 for STA and >=6.2.0.0.47
for AP) use 1 spare TX block. We still want to support older
firmwares that require 2 spare blocks, so added a quirk to handle the
difference.
Also implemented a generic way of setting quirks that depend on the
firmware revision.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Add support to wl128x chip via chip id
Signed-off-by: Shahar Levi <shahar_levi@ti.com>
Reviewed-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Choose a different FW for AP-mode wl127x and wl128x chips, base on chip
ID at boot time.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Reviewed-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Support sending dummy packet to wl128x FW as results of
dummy packet event. That is part of dynamic TX mem blocks mechanism.
Only send dummy packet when not in AP mode.
[Even though the DUMMY_PACKET_EVENT_ID and the
STA_REMOVE_COMPLETE_EVENT_ID events are defined to the same value, we
need to treat them separately in the code. Keep the check and enable
STA_REMOVE_COMPLETE_EVENT_ID for AP mode and DUMMY_PACKET_EVENT_ID for
STA. Moved one warning to a cleaner place. Use WL1271_TID_MGMT for
dummy packets -- Luca]
Signed-off-by: Shahar Levi <shahar_levi@ti.com>
Reviewed-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Reduced bus transactions in the Tx & Rx path.
[Removed unnecessary check wl->chip.id != CHIP_ID_1283_PG20 when
checking the quirk -- Luca]
Signed-off-by: Shahar Levi <shahar_levi@ti.com>
Reviewed-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Separate the memory configuration to chip-specific structures and
implement dynamic memory for wl128x.
This feature allows us to move TX memory blocks to the RX pool when
the RX path is overloaded.
Thanks for Arik Nemtsov <arik@wizery.com> for helping simplify the
wl1271_fw_status() code.
[Rewrote the commit subject and message for clarity; improved some
comments and changed "spare" to "padding" for consistency; added a
FIXME for the AP memory configuration -- Luca]
Signed-off-by: Shahar Levi <shahar_levi@ti.com>
Reviewed-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Boot sequence support FREF clock and TCXO clock.
WL128x has two clocks input - TCXO and FREF.
TCXO is the main clock of the device, while FREF is used to sync
between the GPS and the cellular modem.
Auto-detection checks where TCXO is 32.736MHz or 16.368MHz, in that
case the FREF will be used as the WLAN/BT main clock.
[Use clock enumeration as defined in linux/wl12xx.h; remove
unnecessary else block in wl128x_switch_fref; remove unnecessary
change in main.c; remove some unnecessary debug prints and comments;
fix potential use of uninitialized value (pll_config) -- Luca]
Signed-off-by: Shahar Levi <shahar_levi@ti.com>
Reviewed-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Take care of FW & NVS with the auto-detection between wl127x and
wl128x.
[Moved some common code outside if statements and added notes about
NVS structure assumptions; Fixed a bug when checking the nvs size: if
the size was incorrect, the local nvs variable was set to NULL, it
should be wl->nvs instead. -- Luca]
[Merged with potential buffer overflow fix -- Luca]
Signed-off-by: Shahar Levi <shahar_levi@ti.com>
Reviewed-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
New general and radio parameters structures and functions.
Implemented as separate functions due to auto-detection
between wl127x and wl128x.
Signed-off-by: Shahar Levi <shahar_levi@ti.com>
Reviewed-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Add the the set_block_size op in the SDIO and in the SPI modules.
Since it is only used with SDIO, just explicitly set the op to NULL in
spi.c
Signed-off-by: Luciano Coelho <coelho@ti.com>
New acx command that sets: Rx fifo enable reduced bus transactions
in RX path. Tx bus transactions padding to SDIO block size that
improve preference in Tx and essential for working with SDIO HS (48Mhz).
The max SDIO block size is 256 when working with Tx bus transactions
padding to SDIO block.
Add new ops to SDIO & SPI that handles the win size change in case of
transactions padding (relevant only for SDIO).
[Fix endianess issues; simplify sdio-specific block_size handling;
minor changes in comments; use "aligned_len" in one calculation
instead of "pad" to avoid confusion -- Luca]
Signed-off-by: Shahar Levi <shahar_levi@ti.com>
Reviewed-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Definitions to support wl128x:
- New FW file name
- Chip ID
- New PLL Configuration Algorithm macros that will be used at wl128x
boot stage
- Rename NVS macro name: wl127x and wl128x are using the same NVS
file name. However, the ini parameters between them are
different. The driver will validate the correct NVS size in
wl1271_boot_upload_nvs().
[Cleaned up some of the definitions. -- Luca]
Signed-off-by: Shahar Levi <shahar_levi@ti.com>
Reviewed-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
In order to prevent overran of IRQ polarity via FW the polarity setting move after
FW download and before IRQ enable.
Signed-off-by: Shahar Levi <shahar_levi@ti.com>
Reviewed-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
This also removes private feature flags that were always set to true.
You may want to move vmxnet3_set_features() to vmxnet3_drv.c as a following
cleanup.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
Side effect: ->gro_enable is removed as napi_gro_receive() does the
fallback itself.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
Also remove flags that were not used or are now redundant to hw_features bits.
No device had UDP_CSUM_CAPABLE set.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
This removes advertising HW_CSUM as driver does not support it.
Note: driver advertises TSO6 but not IPV6_CSUM - bug maybe?
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix build warnings like the following:
WARNING: drivers/net/built-in.o(.data+0x12434): Section mismatch in reference from the variable madgemc_driver to the variable .init.data:madgemc_adapter_ids
And add some consts to EISA device ID tables along the way.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
- the MSS value is actually contained in a 11 bits wide (0x7ff) field.
The extra bit in the former MSSMask did encompass the TSO command
bit ("LargeSend") as well (0xfff). Oops.
- the Tx descriptor layout is not the same through the whole chipset
family. The 8169 documentation, the 8168c documentation and Realtek's
drivers (8.020.00, 1.019.00, 6.014.00) highlight two layouts:
1. 8169, 8168 up to 8168b (included) and 8101
2. {8102e, 8168c} and beyond
- notwithstanding the "first descriptor" and "last descriptor" bits, the
same Tx descriptor content is enforced when a packet consists of several
descriptors. The chipsets are documented to require it.
Credits go to David Dillow <dave@thedillows.org> for the original patch.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Realtek <nic_swsd@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit c88fcb (net: dm9000: convert to hw_features) broke the build of
the dm9000 driver since it merged functions which use different names
for the board info structure used for I/O operations without updating
all the references to use the same name. Fix that.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When testing some new P2P code, Angie found that the
driver might crash because the beacon command ended
up being bigger than a regular command. This is quite
obvious -- a normal command is limited to roughly 360
bytes but a beacon may be much larger of course.
To fix this, use the huge command buffer.
Reported-by: Angie Chinchilla <angie.v.chinchilla@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Since huge commands all share a single buffer,
there can only be a single one in flight at a
time since otherwise they'd overwrite each
other. This is true in the driver now, but it
seems like a possible source of bugs, so add
a test to verify that huge commands are always
sent synchronously.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
There are a number of things in the driver that
may result in a BUG(), which is suboptimal since
it's hard to get debugging information out of
the driver in that case and the user experience
is also not good :-)
Almost all BUG_ON instances can be converted to
WARN_ON with a few lines of appropriate error
handling, so do that instead.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
For some reason, sending QoS configuration causes transmission to stop
after a single frame on HT channels when not associated. Removing the
extra QoS configuration has no effect on station mode, and fixes
injection mode.
Signed-off-by: Daniel Halperin <dhalperi@cs.washington.edu>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
It is undesirable for the bonding driver to be poking into higher
level protocols, and notifiers provide a way to avoid that. This does
mean removing the ability to configure reptitition of gratuitous ARPs
and unsolicited NAs.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This updates bnx2x to use the ethtool_cmd_speed() family of functions
(see b11f8d8c in 2.6.27-rc3 aka. "ethtool: Expand ethtool_cmd.speed to
32 bits") to get and set the link speed via ethtool. This allows to
avoid manually accessing ethtool_cmd's speed_hi field.
Signed-off-by: David Decotigny <decot@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Several tests in the ipv6 routing code check IFF_LOOPBACK, and
allowing stacking such as VLAN'ing on top of loopback results in a
netdevice which reports IFF_LOOPBACK but really isn't the loopback
device.
Instead of spamming the ipv6 routing code with even more special tests,
simply disallow VLAN over loopback.
The result of this patch is:
# modprobe 8021q
# vconfig add lo 43
ERROR: trying to add VLAN #43 to IF -:lo:- error: Operation not supported
Signed-off-by: Krishna Kumar <krkumar2@in.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Roger Luethi has had several reports of Rhine NICs providing
an invalid MAC address. If so, assign a random MAC address so
the hardware can still be used.
Tested as a standalone interface, as carrier for ppp, and as a
bonding slave.
Original-patch-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the more current logging styles.
Add #define DEBUG to make netdev_dbg always active.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Acked-by: Dimitris Michailidis <dm@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes port identification on optic devices when there's no link on the port.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Side effect: allow toggling of TX offloads.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
Note: Driver modifies its struct net_device_ops. This will break if used for
multiple devices that are not all the same (if that HW config is possible).
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
Side effect: allow toggling of TX offloads.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove be_set_flags() as it's already covered by hw_features.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Acked-by: Ajit Khaparde ajit.khaparde@emulex.com
Signed-off-by: David S. Miller <davem@davemloft.net>
Side effect: don't reenable RXCSUM on every ifdown/ifup.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
As a side effect, make TX offloads changeable.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
This removes some of the remnants of LRO -> GRO conversion.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
Not much of a conversion anyway - macvlan has no way to change the offload
settings independently to its base device.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
The variables 'tx_min' and 'tx_max' are set but not used in
be_set_coalesce().
Similarly for 'region' in be_do_flash().
Just kill them off.
Signed-off-by: David S. Miller <davem@davemloft.net>
The variable 'rc' is set but unused in bnx2x_timer().
Similarly for 'hc_index_p' in bnx2x_init_sb(), and 'port' in
bnx2x_get_hwinfo().
Just kill them off.
Signed-off-by: David S. Miller <davem@davemloft.net>
The variable 'pgoff' is set but unused in bfa_nw_ioc_fwver_get()
and bfa_ioc_download_fw().
Similarly for 'cmd_h' in bna_mbox_flush_q and the entirety of
bna_rit_mod_uninit() is unused since variables are purely set but no
action is made using them.
Same for 'bna' in bna_rit_create() and 'ret' in bna_rx_create().
Just kill them off.
Signed-off-by: David S. Miller <davem@davemloft.net>
Note: I bet that gfar_set_features() don't really need a full reset.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
This also fixes a race around np->txrxctl_bits while changing RXCSUM offload.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
My changes in commit 4d42d417be were
written some time before the introduction of FLAG_POINTTOPOINT, so
didn't include that flag in the new driver_info. Change the new
driver_info to be consistent.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
This updates the bonding driver to support v2.6.27-rc3 enhancements
(b11f8d8c aka. "ethtool: Expand ethtool_cmd.speed to 32 bits") which
allow to encode the Mbps link speed on 32-bits (Max 4 Pbps) instead of
16 (Max 65536 Mbps).
This patch also attempts to compact struct slave by reordering its
fields.
Signed-off-by: David Decotigny <decot@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The __get_link_speed() function returns a u16 value which was stored
in a u32 local variable. This patch uses the return value directly,
thus fixing that minor type consistency.
The 'duplex' field in struct slave being encoded on 8 bits, to be more
consistent we use a u8 integer (instead of u16) whenever we copy it to
local variables.
Signed-off-by: David Decotigny <decot@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This gets rid of minor sparse complaints:
drivers/net/bonding/bond_main.c:4361:4: warning: do-while statement is not a compound statement
drivers/net/bonding/bond_main.c:243:12: warning: symbol 'bond_mode_name' was not declared. Should it be static?
Signed-off-by: David Decotigny <decot@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The struct nic_operations is just function pointers and should be
declared const for added security.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The phy, mac, and board information structures should be const.
Since tables contain function pointer this improves security
(at least theoretically).
Compile tested only.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Acked-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When physical identification of an adapter is done by toggling the
mechanism on and off through software utilizing the set_phys_id operation,
it is done with a fixed duration for both on and off states. Some drivers
may want to set a custom duration for the on/off intervals. This patch
changes the API so the return code from the driver's entry point when it
is called with ETHTOOL_ID_ACTIVE can specify the frequency at which to
cycle the on/off states, and updates the drivers that have already been
converted to use the new set_phys_id and use the synchronous method for
identifying an adapter.
The physical identification frequency set in the updated drivers is based
on how it was done prior to the introduction of set_phys_id.
Compile tested only. Also fixes a compiler warning in sfc.
v2: drivers do not return -EINVAL for ETHOOL_ID_ACTIVE
v3: fold patchset into single patch and cleanup per Ben's feedback
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Cc: Ben Hutchings <bhutchings@solarflare.com>
Cc: Sathya Perla <sathya.perla@emulex.com>
Cc: Subbu Seetharaman <subbu.seetharaman@emulex.com>
Cc: Ajit Khaparde <ajit.khaparde@emulex.com>
Cc: Michael Chan <mchan@broadcom.com>
Cc: Eilon Greenstein <eilong@broadcom.com>
Cc: Divy Le Ray <divy@chelsio.com>
Cc: Don Fry <pcnet32@frontier.com>
Cc: Jon Mason <jdmason@kudzu.us>
Cc: Solarflare linux maintainers <linux-net-drivers@solarflare.com>
Cc: Steve Hodgson <shodgson@solarflare.com>
Cc: Stephen Hemminger <shemminger@linux-foundation.org>
Cc: Matt Carlson <mcarlson@broadcom.com>
Acked-by: Jon Mason <jdmason@kudzu.us>
Acked-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The memory leak was caused by unintentional assignment of the Rx path
destroy callback function pointer to NULL just after correct
initialization.
Signed-off-by: Debashis Dutt <ddutt@brocade.com>
Signed-off-by: Rasesh Mody <rmody@brocade.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During a kernel crash, bna control path state machine and firmware do not
get a notification and hence are not cleanly shutdown. The registers
holding driver/IOC state information are not reset back to valid
disabled/parking values. This causes subsequent driver initialization
to hang during kdump kernel boot. This patch, during the initialization
of first PCI function, resets corresponding register when unclean shutown
is detect by reading chip registers. This will make sure that ioc/fw
gets clean re-initialization.
Signed-off-by: Debashis Dutt <ddutt@brocade.com>
Signed-off-by: Rasesh Mody <rmody@brocade.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some customers use 0x6C world regulatory domain and this patch
adds the support.
Cc: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In http://lkml.indiana.edu/hypermail/linux/kernel/1104.1/01955.html, Geerti
Uytterhoeven reports the following warnings for the rtlwifi drivers.
src/drivers/net/wireless/rtlwifi/rtl8192c/dm_common.c: warning:
'cck_index' may be used uninitialized in this function: => 637
src/drivers/net/wireless/rtlwifi/rtl8192c/dm_common.c: warning:
'cck_index_old' may be used uninitialized in this function: => 637
src/drivers/net/wireless/rtlwifi/rtl8192c/fw_common.c: warning:
'box_extreg' may be used uninitialized in this function: => 303
src/drivers/net/wireless/rtlwifi/rtl8192c/fw_common.c: warning:
'box_reg' may be used uninitialized in this function: => 303
src/drivers/net/wireless/rtlwifi/rtl8192ce/rf.c: warning:
'chnlgroup' may be used uninitialized in this function: => 205
src/drivers/net/wireless/rtlwifi/rtl8192ce/rf.c: warning:
'u4_regvalue' may be used uninitialized in this function: => 450
src/drivers/net/wireless/rtlwifi/rtl8192cu/hw.c: warning:
'hq_sele' may be used uninitialized in this function: => 924
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The old function name sounds like checking for existing BA
stream. The function actually checks if we have room for
creating new BA stream or not.
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some function parameters become useless after previous
cleanup changes.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The return statement at the last line of a void function
is not necessary.
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
1) remove mwifiex_alloc_fill_wait_queue() and
mwifiex_request_ioctl()
2) avoid dynamic allocation of wait queue
3) remove unnecessary mwifiex_error_code macros that
were used mainly by the wait queue status code
4) remove some abstraction functions
5) split mwifiex_prepare_cmd() to mwifiex_send_cmd_async()
and mwifiex_send_sync() to handle asynchronous and
synchronous commands respectively
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There are two variants of AR5312 dual-band devices, one single-radio
and the other one dual-radio. On the dual-radio board, the first MAC
only supports 5 GHz, even though it has a dual-band PHY. The 2.4 GHz
part of this phy is used in pass-through mode, connecting the second
MAC with the second PHY.
Disable 2.4 GHz for the first MAC on an AR5312, but only if the board
configuration indicates a dual-radio device.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Tested-by: Sedat Dilek <sedat.dilek@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
EEPROM version 5.0 adds a new field for disabling AES support, having
an older version means that AES is present. This patch fixes hw AES
crypto support on AR5312 boards, which have an older EEPROM version.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Tested-by: Sedat Dilek <sedat.dilek@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
On AHB, the calibration data usually does not contain a valid MAC address,
the correct MAC address is stored in the board config.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Tested-by: Sedat Dilek <sedat.dilek@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This struct is not used in any common code, and moving it out of
the ath header makes it easier to add more driver specific ops.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Tested-by: Sedat Dilek <sedat.dilek@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
On a dual-radio dual-band AR5312 device, the calibration data is shared
between the 5 GHz and the 2.4 GHz radio/MAC.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Tested-by: Sedat Dilek <sedat.dilek@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Request a re-configuration of Beacon related timers
on the receipt of the first Beacon frame has to be set only
for station mode. Setting beacon sync for IBSS is causing
wrong beacon slot selection on beacon generation.
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Otherwise, you get this:
CC [M] drivers/net/wireless/ath/ath9k/hif_usb.o
drivers/net/wireless/ath/ath9k/hif_usb.c: In function ‘ath9k_skb_queue_complete’:
drivers/net/wireless/ath/ath9k/hif_usb.c:230:12: error: expected expression before ‘do’
make[2]: *** [drivers/net/wireless/ath/ath9k/hif_usb.o] Error 1
make[1]: *** [drivers/net/wireless/ath/ath9k] Error 2
make: *** [drivers/net/wireless/ath/] Error 2
The TX_STAT_INC macro should probably be changed to accomodate such
usage, although using a trinary operator in place of an if-else seems
questionable to me anyway.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Acked-by: Sujith Manoharan <Sujith.Manoharan@Atheros.com>
DCB enabled X540 devices are not responding to pause frames
due to a missing register set that was added for these
devices that did not exist in other devices.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The X540 device has a smaller packet buffer but the DCB configuration
never took this into account. Under stress this can result in the DMA
engine hanging and TX Unit hang occurring to reset the device. This
patch reworks the packet buffer allocation routine used for DCB on
82599 and X540 devices to account for RX packet buffer sizes.
This fixes the immediate hang. We should consolidate the various
hardware specific routines for configuring features into a single
routine. This will make it much harder to miss feature cases like
this.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Tested-by: Evan Swanson <evan.swanson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
x540 has the same device capability word in the EEPROM as 82599.
This patch renames ixgbe_get_device_caps_82599 to
ixgbe_get_device_caps_generic, moves it to ixgbe_common.h and
sets up the function pointer for x540.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Evan Swanson <evan.swanson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
100H is not supported on this HW, but the bit is set on the PHY.
This can result in link at 100F when advertising only 1000F.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Evan Swanson <evan.swanson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add new device ID supported by ixgbe.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
HW can upload EEPROM content from flash while
in a middle of checksum calculation. Take NVM ownership for the whole
process of checksum update.
Call ixgbe_read_eerd_generic() and ixgbe_write_eewr_generic() directly to
avoid double take of semaphores which leads to long loading times.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Since msleep might not sleep for the desired amount when less
than 20ms use usleep_range.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Disable KR to KX4/KX downshift on 82599 backplane devices when
LESM (Link Establishment State Machine) is enabled in FW. Those
features cannot co-exist as they both manipulate the same registers.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Acked-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Phillip Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Relaxed ordering can lead to issues with some chipsets.
This patch makes sure that it is disabled by default and
not only when DCA is on.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Evan Swanson <evan.swanson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Factored out the common start_hw code into a new function
ixgbe_start_hw_gen2() so that it can be used by x540 and 82599.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Acked-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Evan Swanson <evan.swanson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Acked-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Set ixgbe_identify_82599() as static
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Some 82598 parts have LAN0 disabled and LAN1 enabled and the LAN ID bits in
Device Status register report the NIC as having only LAN1 as enabled. This
causes ixgbe_set_lan_id_multi_port_pcie() to set bus->func = 1 which is
incorrect.
Force bus->func to 0 when LAN0 is disabled in the EEPROM.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Evan Swanson <evan.swanson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The value of status was incorrectly tested. Also whitespace cleanup.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Evan Swanson <evan.swanson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
With the app data on the kernel dcb_app list we no longer
need to specifically handle them in ixgbe for the CEE case.
So now we can remove app handling logic and check when the
hw is configured if the app data matches the hardware
configuration in set_hw_all().
If it does not match then we can reconfigure.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Based on a patch from Naga Chumbalkar <nagananda.chumbalkar@hp.com>:
If ASPM L0s needs to be disabled due to HW errata, do it prior to
"enabling" the device. This way if the kernel ever defaults its
aspm_policy to POLICY_POWERSAVE, then the e1000e driver will get a
chance to disable ASPM on the misbehaving device *prior* to calling
pci_enable_device_mem(). This will be useful in situations
where the BIOS indicates ASPM support on the server by clearing the
ACPI FADT "ASPM Controls" bit.
Note:
The kernel (2.6.38) currently uses the BIOS "default" as its aspm_policy.
However, Linux distros can diverge from that and set the default to
"powersave".
v2: o cleanup namespace pollution of e1000e_disable_aspm(),
o fix type and initialization of the new aspm_disable_flag in a few
functions, and
o redefine FLAG2_DISABLE_ASPM_L0S to the first unused bit in
adapter->flags2.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Cc: Naga Chumbalkar <nagananda.chumbalkar@hp.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Just move the unlock down a bit because it unlocks too
early leaving a chance for get_stats64() run in parallel
while it is still accessing the stats.
Signed-off-by: Flavio Leitner <fleitner@redhat.com>
Acked-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This switches the e1000e driver to use the new VLAN interfaces.
CC: Jesse Gross <jesse@nicira.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Correct the log message when driver loads.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
With durations less than 20ms, the jiffies or legacy timer backed msleep()
may sleep ~20ms which might not be what the caller expects. Instead, it
is recommended to use the hrtimers backed usleep_range(). For more, see
Documentation/timers/timers-howto.txt. Issues reported by checkpatch.
In addition, remove unnecessary sleep in e1000e_write_nvm_spi().
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The code for thermal sensor checking should be wrapped into a function.
Signed-off-by: Stefan Assmann <sassmann@kpanic.de>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Comment spelling fix.
Signed-off-by: Stefan Assmann <sassmann@kpanic.de>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This is a revised patch that permits a shifted access to the
LAN9221 registers. More specifically:
It adds a shift parameter in the platform_data.
It introduces an ops in smsc911x_data.
A choice of access function to use at run-time.
Four new shifted access function.
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Alessandro Rubini <rubini@gnudd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In some devices, the VPD block is relocated to a different area in
NVRAM. The original location can still contain old, but still valid VPD
data. This patch changes the code to look for an extended VPD block in
NVRAM. If one is found, that block is used for all VPD operations
instead.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Reviewed-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds jumbo frame loopback test support to the ethtool
selftest.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Reviewed-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch reimplements the size preprocessor constants of the stats and
ethtool test string arrays. The size is calculated at compile time
rather than using static constants.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Benjamin Li <benli@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch monitors the error bit of the status word within the status
block. If it is set, the driver will dump the driver state after
validating the error and then reset the chip.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Reviewed-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current amount of information provided in the output of a tx timeout
is insufficient to determine a root cause. This patch replaces the
terse, four-register status output with a more complete body of
information. For PCIe devices, the full register space is dumped. For
other devices, select registers are dumped instead.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Reviewed-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some RNDIS devices don't respond on the control channel until polled
on the status channel. In particular, this was reported to be the
case for the 2Wire HomePortal 1000SW and for some Windows Mobile
devices.
This is roughly based on a patch by John Carr <john.carr@unrouted.co.uk>
which is currently applied by Mandriva.
Reported-by: Mark Glassberg <vzeeaxwl@myfairpoint.net>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
New debugfs files:
<debugfs_root>/ath9k_htc/<phy#>/tgt_int_stats
<debugfs_root>/ath9k_htc/<phy#>/tgt_tx_stats
<debugfs_root>/ath9k_htc/<phy#>/tgt_rx_stats
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Beacon transmission needs to involve as little latency
as possible after receiving a SWBA event from the target.
Since packets are buffered to use TX stream mode, beacon
frames sometimes gets queued up and are not sent out immediately.
Fix this by decoupling management frame transmission from the
normal data path and send them out immediately.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Occasionally, a WMI event would arrive ahead of the TX
URB completion handler. Discarding these events would exhaust
the available TX slots, so handle them by running a timer
cleaning up such events. Also, timeout packets for which TX
completion events have not arrived.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Now that the infrastructure is in place, process WMI
TX status events and complete packets.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When a station entry is removed, there could still be
pending packets destined for that station in the HIF layer.
Sending these to the target is not necessary, so drain them
in the driver itself.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There is no point in looping over all the endpoints,
since the HIF layer uses the start/stop APIs only
for the TX pipe. Simplify the API accordingly.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When doing a channel set or a reset operation the pending
frames queued up for transmission have to be flushed and
sent to mac80211. Fixing this has to be done in two separate
steps:
* Flush queued frames and kill the URB TX completion handler.
* Complete all the frames that in the TX pending queue.
This patch adds proper support for draining and all the callsites
namely, channel change/reset/idle/stop are fixed. A separate queue
is used for handling failed frames.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Maintain a bitmap of slots for transmission and update
the cookie field for every packet with the slot value.
This value would be used for matching packets when TX
completion processing is added.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There is no need to do endpoint header removal in the ISR.
Also, this is needed when TX slot management is added later on.
Use a helper function to strip the driver header.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
A new routine that takes an endpoint explicitly is
introduced. The normal htc_send() now retrieves the endpoint
from the packet's private data. This would be useful
in TX completion when the endpoint ID would be required.
While at it, use a helper function to map the queue to endpoint.
Data/mgmt/beacon packets use htc_send(), while WMI comamnds
pass the endpoint to HTC.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Handle queue start/stop properly by maintaining
a counter to check if the pending frame count has
exceeded the threshold. Otherwise, packets would be
dropped needlessly. While at it, use a simple flag
to track queue status and use helper functions too.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Using a single URB for receiving WMI events is
insufficient, increase it to 64 to not lose
WMI events in high throughput situations.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
