As MGPU fan boost feature will be definitely not needed when
DPM is disabled. So, there is no need to error out.
Signed-off-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Problem:
During GPU recover DAL would hang in
amdgpu_pm_compute_clocks->amdgpu_fence_wait_empty
Fix:
Turns out there was a typo introduced by
3320b8d drm/amdgpu: remove job->ring which caused skipping
amdgpu_fence_driver_force_completion and so the hangged job
was never force signaled and this would cause the hang later in DAL.
Signed-off-by: Andrey Grodzovsky <andrey.grodzovsky@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
GVT-g only simulates DP port for guest and leaves EDP_PSR_IMR
and EDP_PSR_IIR registers as default MMIO read/write.
So guest won't get expected initial values of these registers when
initializing the gpu driver, which results in following warning and logs.
--------
Interrupt register 0x64838 is not zero: 0xffffffff
WARNING: CPU: 1 PID: 157 at drivers/gpu/drm/i915/i915_irq.c:177
gen3_assert_iir_is_zero+0x38/0xa0
Call Trace:
gen8_de_irq_postinstall+0xa7/0x400
gen8_irq_postinstall+0x27/0x80
drm_irq_install+0xbc/0x140
i915_driver_load+0xa9d/0xd50
--------
Because GVT-g does not handle EDP(embedded DP) simulation for guests,
always set EDP_PSR_IMR and EDP_PSR_IIR to value 0.
Signed-off-by: Longhe Zheng <longhe.zheng@intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
CSFE_CHICKEN1(0x20d4) needs access with mask. This is caught in AcrnGT
conformance check test:
[drm:intel_gvt_vgpu_conformance_check]
*ERROR* gvt: vgpu1 unconformance mmio 0x20d4:0x40004,0x4
Signed-off-by: Xinyun Liu <xinyun.liu@intel.com>
Signed-off-by: Zhi Wang <zhi.a.wang@intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Previously we assumed two 4-byte writes to the same PTE coming in sequence.
But recently we observed inconsecutive partial write happening as well. So
this patch enhances the previous solution. It now uses a list to save more
partial writes. If one partial write can be combined with another one in
the list to construct a full PTE, update its shadow entry. Otherwise, save
the partial write in the list.
v2: invalidate old entry and flush ggtt (Zhenyu)
v3: split old ggtt page unmap to another patch (Zhenyu)
v4: refine codes (Zhenyu)
Signed-off-by: Hang Yuan <hang.yuan@linux.intel.com>
Cc: Yan Zhao <yan.y.zhao@intel.com>
Cc: Xiaolin Zhang <xiaolin.zhang@intel.com>
Cc: Zhenyu Wang <zhenyu.z.wang@intel.com>
Reviewed-by: Xiaolin Zhang <xiaolin.zhang@intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Tell the version numbers when the pptable versions do not match.
Signed-off-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This patch will work as workaround for silicon limitation
related to PWM dutycycle when the backlight level goes to 0.
Actually PWM value is 16 bit value and valid range from 1-65535.
when ever user requested to set this PWM value to 0 which is not
fall in the range, in VBIOS taken care this by limiting to 1.
This patch here will do the same. Either driver or VBIOS can not
pass 0 value as it is not a valid range for PWM and it will
give a high PWM pulse which is not the intended behaviour as
per HW constraints.
Signed-off-by: suresh guttula <suresh.guttula@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
-----BEGIN PGP SIGNATURE-----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=Cc6D
-----END PGP SIGNATURE-----
Merge tag 'media/v4.20-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media updates from Mauro Carvalho Chehab:
- new dvb frontend driver: lnbh29
- new sensor drivers: imx319 and imx 355
- some old soc_camera driver renames to avoid conflict with new
drivers
- new i.MX Pixel Pipeline (PXP) mem-to-mem platform driver
- a new V4L2 frontend for the FWHT codec
- several other improvements, bug fixes, code cleanups, etc
* tag 'media/v4.20-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (289 commits)
media: rename soc_camera I2C drivers
media: cec: forgot to cancel delayed work
media: vivid: Support 480p for webcam capture
media: v4l2-tpg: fix kernel oops when enabling HFLIP and OSD
media: vivid: Add 16-bit bayer to format list
media: v4l2-tpg-core: Add 16-bit bayer
media: pvrusb2: replace `printk` with `pr_*`
media: venus: vdec: fix decoded data size
media: cx231xx: fix potential sign-extension overflow on large shift
media: dt-bindings: media: rcar_vin: add device tree support for r8a7744
media: isif: fix a NULL pointer dereference bug
media: exynos4-is: make const array config_ids static
media: cx23885: make const array addr_list static
media: ivtv: make const array addr_list static
media: bttv-input: make const array addr_list static
media: cx18: Don't check for address of video_dev
media: dw9807-vcm: Fix probe error handling
media: dw9714: Remove useless error message
media: dw9714: Fix error handling in probe function
media: cec: name for RC passthrough device does not need 'RC for'
...
As far as I can tell the panel that was added in commit da50bd4258
("drm/panel: simple: Add Innolux TV123WAM panel driver support")
wasn't actually an Innolux TV123WAM but was actually an Innolux
P120ZDG-BF1.
As far as I can tell the Innolux TV123WAM isn't a real panel and but
it's a mosh between the TI TV123WAM and the Innolux P120ZDG-BF1.
Let's unmosh.
Here's my evidence:
* Searching for TV123WAM on the Internet turns up a TI panel. While
it's possible that an Innolux panel has the same model number as the
TI Panel, it seems a little doubtful. Looking up the datasheet from
the TI Panel shows that it's 1920 x 1280 and 259.2 mm x 172.8 mm.
* As far as I know, the patch adding the Innolux Panel was supposed to
be for the board that's sitting in front of me as I type this
(support for that board is not yet upstream). On the back of that
panel I see Innolux P120ZDZ-EZ1 rev B1.
* Someone pointed me at a datasheet that's supposed to be for the
panel in front of me (sorry, I can't share the datasheet). That
datasheet has the string "p120zdg-bf1"
* If I search for "P120ZDG-BF1" on the Internet I get hits for panels
that are 2160x1440. They don't have datasheets, but the fact that
the resolution matches is a good sign.
In any case, let's update the name and also the physical size to match
the correct panel.
Fixes: da50bd4258 ("drm/panel: simple: Add Innolux TV123WAM panel driver support")
Cc: Sandeep Panda <spanda@codeaurora.org>
Reviewed-by: Abhinav Kumar <abhinavk@codeaurora.org>
Reviewed-by: Sean Paul <sean@poorly.run>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20181025222134.174583-6-dianders@chromium.org
Let's solve the mystery of commit bf1178c989 ("drm/bridge:
ti-sn65dsi86: Add mystery delay to enable()"). Specifically the
reason we needed that mystery delay is that we weren't paying
attention to HPD.
Looking at the datasheet for the same panel that was tested for the
original commit, I see there's a timing "t3" that times from power on
to the aux channel being operational. This time is specced as 0 - 200
ms. The datasheet says that the aux channel is operational at exactly
the same time that HPD is asserted.
Scoping the signals on this board showed that HPD was asserted 84 ms
after power was asserted. That very closely matches the magic 70 ms
delay that we had. ...and actually, in my testing the 70 ms wasn't
quite enough of a delay and some percentage of the time the display
didn't come up until I bumped it to 100 ms (presumably 84 ms would
have worked too).
To solve this, we tried to hook up the HPD signal in the bridge.
...but in doing so we found that that the bridge didn't report that
HPD was asserted until ~280 ms after we powered it (!). This is
explained by looking at the sn65dsi86 datasheet section "8.4.5.1 HPD
(Hot Plug/Unplug Detection)". Reading there we see that the bridge
isn't even intended to report HPD until 100 ms after it's asserted.
...but that would have left us at 184 ms. The extra 100 ms
(presumably) comes from this part in the datasheet:
> The HPD state machine operates off an internal ring oscillator. The
> ring oscillator frequency will vary [ ... ]. The min/max range in
> the HPD State Diagram refers to the possible times based off
> variation in the ring oscillator frequency.
Given that the 280 ms we'll end up delaying if we hook up HPD is
_slower_ than the 200 ms we could just hardcode, for now we'll solve
the problem by just hardcoding a 200 ms delay in the panel driver
using the patch in this series ("drm/panel: simple: Support panels
with HPD where HPD isn't connected").
If we later find a panel that needs to use this bridge where we need
HPD then we'll have to come up with some new code to handle it. Given
the silly debouncing in the bridge chip, though, it seems unlikely.
One last note is that I tried to solve this through another way: In
ti_sn_bridge_enable() I tried to use various combinations of
dp_dpcd_writeb() and dp_dpcd_readb() to detect when the aux channel
was up. In theory that would let me detect _exactly_ when I could
continue and do link training. Unfortunately even if I did an aux
transfer w/out waiting I couldn't see any errors. Possibly I could
keep looping over link training until it came back with success, but
that seemed a little overly hacky to me.
Reviewed-by: Sean Paul <sean@poorly.run>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20181025222134.174583-4-dianders@chromium.org
If the HPD signal isn't hooked up to this panel we need a 200 ms
delay. In the datasheet this is shown as the maximum time that HPD
will take to be asserted after power is given to the panel.
Reviewed-by: Sean Paul <sean@poorly.run>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20181025222134.174583-3-dianders@chromium.org
Some eDP panels that are designed to be always connected to a board
use their HPD signal to signal that they've finished powering on and
they're ready to be talked to.
However, for various reasons it's possible that the HPD signal from
the panel isn't actually hooked up. In the case where the HPD isn't
hooked up you can look at the timing diagram on the panel datasheet
and insert a delay for the maximum amount of time that the HPD might
take to come up.
Let's add support in simple-panel for this concept.
At the moment we will co-opt the existing "prepare" delay to keep
track of the delay and we'll use a boolean to specify that a given
panel should only apply the delay if the "no-hpd" property was
specified.
Reviewed-by: Sean Paul <sean@poorly.run>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20181025222134.174583-2-dianders@chromium.org
BOE panel (ID: 0x0771) that reports "DFP 1.x compliant TMDS".
But it's 6bpc panel only instead of 8 bpc.
Add panel ID to edid quirk list and set 6 bpc as default to
work around this issue.
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Gustavo Padovan <gustavo@padovan.org>
Cc: Cooper Chiou <cooper.chiou@intel.com>
Signed-off-by: Lee, Shawn C <shawn.c.lee@intel.com>>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/1540792173-7288-1-git-send-email-shawn.c.lee@intel.com
-----BEGIN PGP SIGNATURE-----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=3yxi
-----END PGP SIGNATURE-----
Merge tag 'drm-next-2018-10-24' of git://anongit.freedesktop.org/drm/drm
Pull drm updates from Dave Airlie:
"This is going to rebuild more than drm as it adds a new helper to
list.h for doing bulk updates. Seemed like a reasonable addition to
me.
Otherwise the usual merge window stuff lots of i915 and amdgpu, not so
much nouveau, and piles of everything else.
Core:
- Adds a new list.h helper for doing bulk list updates for TTM.
- Don't leak fb address in smem_start to userspace (comes with EXPORT
workaround for people using mali out of tree hacks)
- udmabuf device to turn memfd regions into dma-buf
- Per-plane blend mode property
- ref/unref replacements with get/put
- fbdev conflicting framebuffers code cleaned up
- host-endian format variants
- panel orientation quirk for Acer One 10
bridge:
- TI SN65DSI86 chip support
vkms:
- GEM support.
- Cursor support
amdgpu:
- Merge amdkfd and amdgpu into one module
- CEC over DP AUX support
- Picasso APU support + VCN dynamic powergating
- Raven2 APU support
- Vega20 enablement + kfd support
- ACP powergating improvements
- ABGR/XBGR display support
- VCN jpeg support
- xGMI support
- DC i2c/aux cleanup
- Ycbcr 4:2:0 support
- GPUVM improvements
- Powerplay and powerplay endian fixes
- Display underflow fixes
vmwgfx:
- Move vmwgfx specific TTM code to vmwgfx
- Split out vmwgfx buffer/resource validation code
- Atomic operation rework
bochs:
- use more helpers
- format/byteorder improvements
qxl:
- use more helpers
i915:
- GGTT coherency getparam
- Turn off resource streamer API
- More Icelake enablement + DMC firmware
- Full PPGTT for Ivybridge, Haswell and Valleyview
- DDB distribution based on resolution
- Limited range DP display support
nouveau:
- CEC over DP AUX support
- Initial HDMI 2.0 support
virtio-gpu:
- vmap support for PRIME objects
tegra:
- Initial Tegra194 support
- DMA/IOMMU integration fixes
msm:
- a6xx perf improvements + clock prefix
- GPU preemption optimisations
- a6xx devfreq support
- cursor support
rockchip:
- PX30 support
- rgb output interface support
mediatek:
- HDMI output support on mt2701 and mt7623
rcar-du:
- Interlaced modes on Gen3
- LVDS on R8A77980
- D3 and E3 SoC support
hisilicon:
- misc fixes
mxsfb:
- runtime pm support
sun4i:
- R40 TCON support
- Allwinner A64 support
- R40 HDMI support
omapdrm:
- Driver rework changing display pipeline ordering to use common code
- DMM memory barrier and irq fixes
- Errata workarounds
exynos:
- out-bridge support for LVDS bridge driver
- Samsung 16x16 tiled format support
- Plane alpha and pixel blend mode support
tilcdc:
- suspend/resume update
mali-dp:
- misc updates"
* tag 'drm-next-2018-10-24' of git://anongit.freedesktop.org/drm/drm: (1382 commits)
firmware/dmc/icl: Add missing MODULE_FIRMWARE() for Icelake.
drm/i915/icl: Fix signal_levels
drm/i915/icl: Fix DDI/TC port clk_off bits
drm/i915/icl: create function to identify combophy port
drm/i915/gen9+: Fix initial readout for Y tiled framebuffers
drm/i915: Large page offsets for pread/pwrite
drm/i915/selftests: Disable shrinker across mmap-exhaustion
drm/i915/dp: Link train Fallback on eDP only if fallback link BW can fit panel's native mode
drm/i915: Fix intel_dp_mst_best_encoder()
drm/i915: Skip vcpi allocation for MSTB ports that are gone
drm/i915: Don't unset intel_connector->mst_port
drm/i915: Only reset seqno if actually idle
drm/i915: Use the correct crtc when sanitizing plane mapping
drm/i915: Restore vblank interrupts earlier
drm/i915: Check fb stride against plane max stride
drm/amdgpu/vcn:Fix uninitialized symbol error
drm: panel-orientation-quirks: Add quirk for Acer One 10 (S1003)
drm/amd/amdgpu: Fix debugfs error handling
drm/amdgpu: Update gc_9_0 golden settings.
drm/amd/powerplay: update PPtable with DC BTC and Tvr SocLimit fields
...
- Remove unused fallback for BUILD_BUG_ON (which technically contains a VLA)
- Lift -Wvla to the top-level Makefile
-----BEGIN PGP SIGNATURE-----
Comment: Kees Cook <kees@outflux.net>
iQJKBAABCgA0FiEEpcP2jyKd1g9yPm4TiXL039xtwCYFAlvV7jMWHGtlZXNjb29r
QGNocm9taXVtLm9yZwAKCRCJcvTf3G3AJkUwD/46aPTmVXQqzVr1QxRC087Aou5H
hCMaUSG0mSuinhIpB398xh58imTqz48n44gf8yrBgittecV+g8cQ3TJZBp8fSbj4
zyuSy0xlghxqNYhsirMPdN61A8qOS/F7i60XFBXSKpdzKorUUsqlP6paDg1CWslB
KWIOr2aHxvQk93pHFsWjOeM7CGqQIq1brKKDPAL+R4zj8EzXfi0s1sOR4tHCXRZP
sTsuHysAjsBlaw54tvbCA5SIyABzZK5xsQoeChSKMoCDQb8TOQK4j8f78470/nmk
lFWZWGKFr2sPUPcuf1casL5Cp57ycjwi4qTzKX2Qa1hhEhrYTIvcOwzOWdc0AY+6
Fttbopla1QmrGndLtm8FOJRGWiCAzhiSpV9vk1VDaP2jeCc6MEvTC0shsAgxSfsr
JRIHqq37w3TBr78qeNuxOaSEkoqtjTVYug2aq7kefG66DGGChzCTVNQrLVNei3Qg
ZdamzUZz7FVV6WmXlWsBfbm14sIRd02r7XORm0cJdIVvIwqJ9QIGJigR/Sfc4Qdi
pXuuE3TNSfArACXlCkaBfqMYAhWO35qy41TerRlRDkri89DNHPY8RAVV0GpNSp7q
kPaPBHZRKXAjHPnnypXz3A/zQoqJ7uWRG5msethAWtEXJBQ4qQWVhjTNmV7tkOkr
HIaJFTb03LLIcuv23Q==
=Vnw8
-----END PGP SIGNATURE-----
Merge tag 'vla-v4.20-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux
Pull VLA removal from Kees Cook:
"Globally warn on VLA use.
This turns on "-Wvla" globally now that the last few trees with their
VLA removals have landed (crypto, block, net, and powerpc).
Arnd mentioned that there may be a couple more VLAs hiding in
hard-to-find randconfigs, but nothing big has shaken out in the last
month or so in linux-next.
We should be basically VLA-free now! Wheee. :)
Summary:
- Remove unused fallback for BUILD_BUG_ON (which technically contains
a VLA)
- Lift -Wvla to the top-level Makefile"
* tag 'vla-v4.20-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux:
Makefile: Globally enable VLA warning
compiler.h: give up __compiletime_assert_fallback()
Pull XArray conversion from Matthew Wilcox:
"The XArray provides an improved interface to the radix tree data
structure, providing locking as part of the API, specifying GFP flags
at allocation time, eliminating preloading, less re-walking the tree,
more efficient iterations and not exposing RCU-protected pointers to
its users.
This patch set
1. Introduces the XArray implementation
2. Converts the pagecache to use it
3. Converts memremap to use it
The page cache is the most complex and important user of the radix
tree, so converting it was most important. Converting the memremap
code removes the only other user of the multiorder code, which allows
us to remove the radix tree code that supported it.
I have 40+ followup patches to convert many other users of the radix
tree over to the XArray, but I'd like to get this part in first. The
other conversions haven't been in linux-next and aren't suitable for
applying yet, but you can see them in the xarray-conv branch if you're
interested"
* 'xarray' of git://git.infradead.org/users/willy/linux-dax: (90 commits)
radix tree: Remove multiorder support
radix tree test: Convert multiorder tests to XArray
radix tree tests: Convert item_delete_rcu to XArray
radix tree tests: Convert item_kill_tree to XArray
radix tree tests: Move item_insert_order
radix tree test suite: Remove multiorder benchmarking
radix tree test suite: Remove __item_insert
memremap: Convert to XArray
xarray: Add range store functionality
xarray: Move multiorder_check to in-kernel tests
xarray: Move multiorder_shrink to kernel tests
xarray: Move multiorder account test in-kernel
radix tree test suite: Convert iteration test to XArray
radix tree test suite: Convert tag_tagged_items to XArray
radix tree: Remove radix_tree_clear_tags
radix tree: Remove radix_tree_maybe_preload_order
radix tree: Remove split/join code
radix tree: Remove radix_tree_update_node_t
page cache: Finish XArray conversion
dax: Convert page fault handlers to XArray
...
- Sync dtc with upstream version v1.4.7-14-gc86da84d30e4
- Work to get rid of direct accesses to struct device_node name and
type pointers in preparation for removing them. New helpers for
parsing DT cpu nodes and conversions to use the helpers. printk
conversions to %pOFn for printing DT node names. Most went thru
subystem trees, so this is the remainder.
- Fixes to DT child node lookups to actually be restricted to child
nodes instead of treewide.
- Refactoring of dtb targets out of arch code. This makes the support
more uniform and enables building all dtbs on c6x, microblaze, and
powerpc.
- Various DT binding updates for Renesas r8a7744 SoC
- Vendor prefixes for Facebook, OLPC
- Restructuring of some ARM binding docs moving some peripheral bindings
out of board/SoC binding files
- New "secure-chosen" binding for secure world settings on ARM
- Dual licensing of 2 DT IRQ binding headers
-----BEGIN PGP SIGNATURE-----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=335v
-----END PGP SIGNATURE-----
Merge tag 'devicetree-for-4.20' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull Devicetree updates from Rob Herring:
"A bit bigger than normal as I've been busy this cycle.
There's a few things with dependencies and a few things subsystem
maintainers didn't pick up, so I'm taking them thru my tree.
The fixes from Johan didn't get into linux-next, but they've been
waiting for some time now and they are what's left of what subsystem
maintainers didn't pick up.
Summary:
- Sync dtc with upstream version v1.4.7-14-gc86da84d30e4
- Work to get rid of direct accesses to struct device_node name and
type pointers in preparation for removing them. New helpers for
parsing DT cpu nodes and conversions to use the helpers. printk
conversions to %pOFn for printing DT node names. Most went thru
subystem trees, so this is the remainder.
- Fixes to DT child node lookups to actually be restricted to child
nodes instead of treewide.
- Refactoring of dtb targets out of arch code. This makes the support
more uniform and enables building all dtbs on c6x, microblaze, and
powerpc.
- Various DT binding updates for Renesas r8a7744 SoC
- Vendor prefixes for Facebook, OLPC
- Restructuring of some ARM binding docs moving some peripheral
bindings out of board/SoC binding files
- New "secure-chosen" binding for secure world settings on ARM
- Dual licensing of 2 DT IRQ binding headers"
* tag 'devicetree-for-4.20' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (78 commits)
ARM: dt: relicense two DT binding IRQ headers
power: supply: twl4030-charger: fix OF sibling-node lookup
NFC: nfcmrvl_uart: fix OF child-node lookup
net: stmmac: dwmac-sun8i: fix OF child-node lookup
net: bcmgenet: fix OF child-node lookup
drm/msm: fix OF child-node lookup
drm/mediatek: fix OF sibling-node lookup
of: Add missing exports of node name compare functions
dt-bindings: Add OLPC vendor prefix
dt-bindings: misc: bk4: Add device tree binding for Liebherr's BK4 SPI bus
dt-bindings: thermal: samsung: Add SPDX license identifier
dt-bindings: clock: samsung: Add SPDX license identifiers
dt-bindings: timer: ostm: Add R7S9210 support
dt-bindings: phy: rcar-gen2: Add r8a7744 support
dt-bindings: can: rcar_can: Add r8a7744 support
dt-bindings: timer: renesas, cmt: Document r8a7744 CMT support
dt-bindings: watchdog: renesas-wdt: Document r8a7744 support
dt-bindings: thermal: rcar: Add device tree support for r8a7744
Documentation: dt: Add binding for /secure-chosen/stdout-path
dt-bindings: arm: zte: Move sysctrl bindings to their own doc
...
Currently send_msg_to_smc_async() only report which message
failed, but the actual failing message is the previous one,
which SMU is unable to service.
This patch reads the contents of register where the SMU is stuck
and report appropriately.
v2: fix the build (Alex)
Signed-off-by: Shirish S <shirish.s@amd.com>
Reviewed-by: Rex Zhu <Rex.Zhu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Problem: After GPU reset on dGPUs with gfx8 compute ring
1.0.0 fails to pass the ring test. Ring registers inspection
shows that it's active and no hang is observed (rptr == wptr)
No significant diffs were observed between CP_HQD* registers
for the ring in good and bad shape.
Fix: No clear reason why but reversing the order of ring tests
fixes the problem.
Signed-off-by: Andrey Grodzovsky <andrey.grodzovsky@amd.com>
Acked-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Make sure we don't try to go down further after the leave walk already
ended. This fixes a crash with a new VM test.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Tested-by: Rex Zhu Rex.Zhu@amd.com
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
We should not remove mappings in rbtree_postorder_for_each_entry_safe
because that rebalances the tree.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Chunming Zhou <david1.zhou@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
So that it can be shared between all clocks.
Signed-off-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Feifei Xu<Feifei.Xu@amd.com>
Reviewed-by: Rex Zhu <Rex.Zhu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Currently the clocks reported are in 10Khz unit. Correct them
as Khz unit as DAL wanted.
Signed-off-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Feifei Xu<Feifei.Xu@amd.com>
Reviewed-by: Rex Zhu <Rex.Zhu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Carrizo and Stoney have severe corruption when trying to power
4k 60 monitors over HDMI connectors that support 4k 60.
Carrizo and Stoney require retimers and redrivers to support 4k 60
over HDMI. This driver does not currently support these. Thus, 4k 60
HDMI (and all other modes requiring over 300MHz) should be disabled.
[How]
Reduce the dce11 HDMI pixel clock cap to 300000kHz.
Signed-off-by: David Francis <David.Francis@amd.com>
Reviewed-by: Roman Li <Roman.Li@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
need to check adev->powerplay.pp_funcs first, becasue from
AI, the smu ip can be disabled by user, and the pp_handle
is null in this case.
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Rex Zhu <Rex.Zhu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
from AI, SMU Ip is not indispensable to driver and can be
disabled by user via module parameter ip_block_mask.
so the pp_handle may be NULL.
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Rex Zhu <Rex.Zhu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This can suppress the error reported on driver loading. Also these
are empty APIs as Vega12/Vega20 has no performance levels.
Signed-off-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Feifei Xu <Feifei.Xu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Commit '3cf71bc9904d ("drm/i915: Re-apply "Perform link quality check,
unconditionally during long pulse"")' applies a work around for sinks
that don't signal link loss. The work around does not need to have to be
that broad as the issue was seen with only one particular monitor; limit
this only for external displays as eDP features like PSR turn off the link
and the driver ends up retraining the link seeeing that link is not
synchronized.
Cc: Lyude Paul <lyude@redhat.com>
Cc: Jan-Marek Glogowski <glogow@fbihome.de>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
References: 3cf71bc990 ("drm/i915: Re-apply "Perform link quality check, unconditionally during long pulse"")
Signed-off-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180927205735.16651-2-dhinakaran.pandiyan@intel.com
(cherry picked from commit f24f6eb958)
Fixes: 399334708b ("drm/i915: Re-apply "Perform link quality check, unconditionally during long pulse"")
Cc: stable@vger.kernel.org
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Comment claims link needs to be retrained because the connected sink raised
a long pulse to indicate link loss. If the sink did so,
intel_dp_hotplug() would have handled link retraining. Looking at the
logs in Bugzilla referenced in commit '3cf71bc9904d ("drm/i915: Re-apply
Perform link quality check, unconditionally during long pulse"")', the
issue is that the sink does not trigger an interrupt. What we want is
->detect() from user space to check link status and retrain. Ville's
review for the original patch also indicates the same root cause. So,
rewrite the comment.
v2: Patch split and rewrote comment.
Cc: Lyude Paul <lyude@redhat.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Jan-Marek Glogowski <glogow@fbihome.de>
References: 3cf71bc990 ("drm/i915: Re-apply "Perform link quality check, unconditionally during long pulse"")
Signed-off-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180927205735.16651-1-dhinakaran.pandiyan@intel.com
(cherry picked from commit 9ebd820239)
Fixes: 399334708b ("drm/i915: Re-apply "Perform link quality check, unconditionally during long pulse"")
Cc: stable@vger.kernel.org
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Remove the undefinition of READ and WRITE because these constants may be
used elsewhere in subsequently included header files, thus breaking them.
These constants don't actually appear to be used in the driver, so the
undefinition seems pointless.
Fixes: 4562236b3b ("drm/amd/dc: Add dc display driver (v2)")
Signed-off-by: David Howells <dhowells@redhat.com>
Use the new of_get_compatible_child() helper to lookup the legacy
pwrlevels child node instead of using of_find_compatible_node(), which
searches the entire tree from a given start node and thus can return an
unrelated (i.e. non-child) node.
This also addresses a potential use-after-free (e.g. after probe
deferral) as the tree-wide helper drops a reference to its first
argument (i.e. the probed device's node).
While at it, also fix the related child-node reference leak.
Fixes: e2af8b6b0c ("drm/msm: gpu: Use OPP tables if we can")
Cc: stable <stable@vger.kernel.org> # 4.12
Cc: Jordan Crouse <jcrouse@codeaurora.org>
Cc: Rob Clark <robdclark@gmail.com>
Cc: David Airlie <airlied@linux.ie>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Rob Herring <robh@kernel.org>
Use the new of_get_compatible_child() helper to lookup the sibling
instead of using of_find_compatible_node(), which searches the entire
tree from a given start node and thus can return an unrelated (i.e.
non-sibling) node.
This also addresses a potential use-after-free (e.g. after probe
deferral) as the tree-wide helper drops a reference to its first
argument (i.e. the parent device node).
While at it, also fix the related cec-node reference leak.
Fixes: 8f83f26891 ("drm/mediatek: Add HDMI support")
Cc: stable <stable@vger.kernel.org> # 4.8
Cc: Junzhi Zhao <junzhi.zhao@mediatek.com>
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Cc: CK Hu <ck.hu@mediatek.com>
Cc: David Airlie <airlied@linux.ie>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Rob Herring <robh@kernel.org>
As the matching VBIOS is already ready. Also drop the
temporary workarounds applied before.
Signed-off-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Feifei Xu <Feifei.Xu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The UCLK is forced to highest at the start of display configuration
change. Downgrade the UCLK from highest after display configuration change.
Otherwise, we may see the UCLK stuck in the highest in some cases.
Signed-off-by: Evan Quan <evan.quan@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
OverDrive mode allows users to increase the maximum SCLK and MCLK
frequencies beyond the default on the GPU. However, this may not
results in large performance gains if the GPU then runs into its TDP
power limit. This patch adds the capability to increase the power
limit of a GPU above its default maximum.
This is only allowed when overdrive is enabled in the ppfeaturemask,
since this is an overdrive feature. The TDPODLimit value from the
VBIOS describes how how much higher the TDP should be allowed to go
over its default, in percentage.
v2: Moved dereference of hwmgr to after its validity check
Signed-off-by: Joseph Greathouse <Joseph.Greathouse@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
In a refactor, the watermark clock inputs to
powerplay from DC were changed from units of 10kHz to
kHz clocks.
One division by 100 was not converted into a division
by 1000.
Signed-off-by: David Francis <David.Francis@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Need to check adev->powerplay.pp_funcs.
Signed-off-by: Emily Deng <Emily.Deng@amd.com>
Reviewed-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Forcing clock level is supported under manual dpm mode only. Error out
when trying to set under manual mode. Instead of doing nothing and
reporting success.
V2: update for mclk/pcie clock level settings also
Signed-off-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
- Fix ulong overflow in sun4i
- Fix a serious GPF in waiting for flip_done from commit_tail().
-----BEGIN PGP SIGNATURE-----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=3i14
-----END PGP SIGNATURE-----
Merge tag 'drm-misc-fixes-2018-10-19' of git://anongit.freedesktop.org/drm/drm-misc into drm-fixes
Second pull request for v4.19:
- Fix ulong overflow in sun4i
- Fix a serious GPF in waiting for flip_done from commit_tail().
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/97d1ed42-1d99-fcc5-291e-cd1dc29a4252@linux.intel.com
The calculated ideal rate can easily overflow an unsigned long, thus
making the best div selection buggy as soon as no ideal match is found
before the overflow occurs.
Fixes: 4731a72df2 ("drm/sun4i: request exact rates to our parents")
Cc: <stable@vger.kernel.org>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181018100250.12565-1-boris.brezillon@bootlin.com
As mentioned in the previous commit, we currently prevent new modesets
on recently-removed MST connectors by returning no encoder from our
->best_encoder() callback once the MST port has disappeared. This is
wrong however, because it prevents legacy modesetting users from being
able to disable CRTCs on MST connectors after the connector's respective
topology has disappeared.
So, fix this by instead by just always returning a valid encoder.
Changes since v2:
- Remove usage of atomic MST helper for now, since that got replaced
with a much simpler solution
Signed-off-by: Lyude Paul <lyude@redhat.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Ben Skeggs <bskeggs@redhat.com>
Cc: stable@vger.kernel.org
Link: https://patchwork.freedesktop.org/patch/msgid/20181008232437.5571-3-lyude@redhat.com
(cherry picked from commit e87b0bbc9f)
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Unfortunately, it appears our fix in:
commit b5d29843d8 ("drm/atomic_helper: Allow DPMS On<->Off changes
for unregistered connectors")
Which attempted to work around the problems introduced by:
commit 4d80273976 ("drm/atomic_helper: Disallow new modesets on
unregistered connectors")
Is still not the right solution, as modesets can still be triggered
outside of drm_atomic_set_crtc_for_connector().
So in order to fix this, while still being careful that we don't break
modesets that a driver may perform before being registered with
userspace, we replace connector->registered with a tristate member,
connector->registration_state. This allows us to keep track of whether
or not a connector is still initializing and hasn't been exposed to
userspace, is currently registered and exposed to userspace, or has been
legitimately removed from the system after having once been present.
Using this info, we can prevent userspace from performing new modesets
on unregistered connectors while still allowing the driver to perform
modesets on unregistered connectors before the driver has finished being
registered.
Changes since v1:
- Fix WARN_ON() in drm_connector_cleanup() that CI caught with this
patchset in igt@drv_module_reload@basic-reload-inject and
igt@drv_module_reload@basic-reload by checking if the connector is
registered instead of unregistered, as calling drm_connector_cleanup()
on a connector that hasn't been registered with userspace yet should
stay valid.
- Remove unregistered_connector_check(), and just go back to what we
were doing before in commit 4d80273976 ("drm/atomic_helper: Disallow
new modesets on unregistered connectors") except replacing
READ_ONCE(connector->registered) with drm_connector_is_unregistered().
This gets rid of the behavior of allowing DPMS On<->Off, but that should
be fine as it's more consistent with the UAPI we had before - danvet
- s/drm_connector_unregistered/drm_connector_is_unregistered/ - danvet
- Update documentation, fix some typos.
Fixes: b5d29843d8 ("drm/atomic_helper: Allow DPMS On<->Off changes for unregistered connectors")
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: stable@vger.kernel.org
Cc: David Airlie <airlied@linux.ie>
Signed-off-by: Lyude Paul <lyude@redhat.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20181016203946.9601-1-lyude@redhat.com
(cherry picked from commit 39b50c6038)
Fixes: e96550956f ("drm/atomic_helper: Disallow new modesets on unregistered connectors")
Fixes: 34ca26a98a ("drm/atomic_helper: Allow DPMS On<->Off changes for unregistered connectors")
Cc: stable@vger.kernel.org
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
It appears when testing my previous fix for some of the legacy
modesetting issues with MST, I misattributed some kernel splats that
started appearing on my machine after a rebase as being from upstream.
But it appears they actually came from my patch series:
[ 2.980512] [drm:drm_atomic_helper_check_modeset [drm_kms_helper]] Updating routing for [CONNECTOR:65:eDP-1]
[ 2.980516] [drm:drm_atomic_helper_check_modeset [drm_kms_helper]] [CONNECTOR:65:eDP-1] is not registered
[ 2.980516] ------------[ cut here ]------------
[ 2.980519] Could not determine valid watermarks for inherited state
[ 2.980553] WARNING: CPU: 3 PID: 551 at drivers/gpu/drm/i915/intel_display.c:14983 intel_modeset_init+0x14d7/0x19f0 [i915]
[ 2.980556] Modules linked in: i915(O+) i2c_algo_bit drm_kms_helper(O) syscopyarea sysfillrect sysimgblt fb_sys_fops drm(O) intel_rapl x86_pkg_temp_thermal iTCO_wdt wmi_bmof coretemp crc32_pclmul psmouse i2c_i801 mei_me mei i2c_core lpc_ich mfd_core tpm_tis tpm_tis_core wmi tpm thinkpad_acpi pcc_cpufreq video ehci_pci crc32c_intel serio_raw ehci_hcd xhci_pci xhci_hcd
[ 2.980577] CPU: 3 PID: 551 Comm: systemd-udevd Tainted: G O 4.19.0-rc7Lyude-Test+ #1
[ 2.980579] Hardware name: LENOVO 20BWS1KY00/20BWS1KY00, BIOS JBET63WW (1.27 ) 11/10/2016
[ 2.980605] RIP: 0010:intel_modeset_init+0x14d7/0x19f0 [i915]
[ 2.980607] Code: 89 df e8 ec 27 02 00 e9 24 f2 ff ff be 03 00 00 00 48 89 df e8 da 27 02 00 e9 26 f2 ff ff 48 c7 c7 c8 d1 34 a0 e8 23 cf dc e0 <0f> 0b e9 7c fd ff ff f6 c4 04 0f 85 37 f7 ff ff 48 8b 83 60 08 00
[ 2.980611] RSP: 0018:ffffc90000287988 EFLAGS: 00010282
[ 2.980614] RAX: 0000000000000000 RBX: ffff88031b488000 RCX: 0000000000000006
[ 2.980617] RDX: 0000000000000007 RSI: 0000000000000086 RDI: ffff880321ad54d0
[ 2.980620] RBP: ffffc90000287a10 R08: 000000000000040a R09: 0000000000000065
[ 2.980623] R10: ffff88030ebb8f00 R11: ffffffff81416590 R12: ffff88031b488000
[ 2.980626] R13: ffff88031b4883a0 R14: ffffc900002879a8 R15: ffff880319099800
[ 2.980630] FS: 00007f475620d180(0000) GS:ffff880321ac0000(0000) knlGS:0000000000000000
[ 2.980633] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 2.980636] CR2: 00007f9ef28018a0 CR3: 000000031b72c001 CR4: 00000000003606e0
[ 2.980639] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[ 2.980642] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
[ 2.980645] Call Trace:
[ 2.980675] i915_driver_load+0xb0e/0xdc0 [i915]
[ 2.980681] ? kernfs_add_one+0xe7/0x130
[ 2.980709] i915_pci_probe+0x46/0x60 [i915]
[ 2.980715] pci_device_probe+0xd4/0x150
[ 2.980719] really_probe+0x243/0x3b0
[ 2.980722] driver_probe_device+0xba/0x100
[ 2.980726] __driver_attach+0xe4/0x110
[ 2.980729] ? driver_probe_device+0x100/0x100
[ 2.980733] bus_for_each_dev+0x74/0xb0
[ 2.980736] driver_attach+0x1e/0x20
[ 2.980739] bus_add_driver+0x159/0x230
[ 2.980743] ? 0xffffffffa0393000
[ 2.980746] driver_register+0x70/0xc0
[ 2.980749] ? 0xffffffffa0393000
[ 2.980753] __pci_register_driver+0x57/0x60
[ 2.980780] i915_init+0x55/0x58 [i915]
[ 2.980785] do_one_initcall+0x4a/0x1c4
[ 2.980789] ? do_init_module+0x27/0x210
[ 2.980793] ? kmem_cache_alloc_trace+0x131/0x190
[ 2.980797] do_init_module+0x60/0x210
[ 2.980800] load_module+0x2063/0x22e0
[ 2.980804] ? vfs_read+0x116/0x140
[ 2.980807] ? vfs_read+0x116/0x140
[ 2.980811] __do_sys_finit_module+0xbd/0x120
[ 2.980814] ? __do_sys_finit_module+0xbd/0x120
[ 2.980818] __x64_sys_finit_module+0x1a/0x20
[ 2.980821] do_syscall_64+0x5a/0x110
[ 2.980824] entry_SYSCALL_64_after_hwframe+0x44/0xa9
[ 2.980826] RIP: 0033:0x7f4754e32879
[ 2.980828] Code: 00 c3 66 2e 0f 1f 84 00 00 00 00 00 0f 1f 44 00 00 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 8b 0d f7 45 2c 00 f7 d8 64 89 01 48
[ 2.980831] RSP: 002b:00007fff43fd97d8 EFLAGS: 00000246 ORIG_RAX: 0000000000000139
[ 2.980834] RAX: ffffffffffffffda RBX: 0000559a44ca64f0 RCX: 00007f4754e32879
[ 2.980836] RDX: 0000000000000000 RSI: 00007f475599f4cd RDI: 0000000000000018
[ 2.980838] RBP: 00007f475599f4cd R08: 0000000000000000 R09: 0000000000000000
[ 2.980839] R10: 0000000000000018 R11: 0000000000000246 R12: 0000000000000000
[ 2.980841] R13: 0000559a44c92fd0 R14: 0000000000020000 R15: 0000000000000000
[ 2.980881] WARNING: CPU: 3 PID: 551 at drivers/gpu/drm/i915/intel_display.c:14983 intel_modeset_init+0x14d7/0x19f0 [i915]
[ 2.980884] ---[ end trace 5eb47a76277d4731 ]---
The cause of this appears to be due to the fact that if there's
pre-existing display state that was set by the BIOS when i915 loads, it
will attempt to perform a modeset before the driver is registered with
userspace. Since this happens before the driver's registered with
userspace, it's connectors are also unregistered and thus-states which
would turn on DPMS on a connector end up getting rejected since the
connector isn't registered.
These bugs managed to get past Intel's CI partially due to the fact it
never ran a full test on my patches for some reason, but also because
all of the tests unload the GPU once before running. Since this bug is
only really triggered when the drivers tries to perform a modeset before
it's been fully registered with userspace when coming from whatever
display configuration the firmware left us with, it likely would never
have been picked up by CI in the first place.
After some discussion with vsyrjala, we decided the best course of
action would be to just move the unregistered connector checks out of
update_connector_routing() and into drm_atomic_set_crtc_for_connector().
The reason for this being that legacy modesetting isn't going to be
expecting failures anywhere (at least this is the case with X), so
ideally we want to ensure that any DPMS changes will still work even on
unregistered connectors. Instead, we now only reject new modesets which
would change the current CRTC assigned to an unregistered connector
unless no new CRTC is being assigned to replace the connector's previous
one.
Signed-off-by: Lyude Paul <lyude@redhat.com>
Reported-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Fixes: 4d80273976 ("drm/atomic_helper: Disallow new modesets on unregistered connectors")
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: stable@vger.kernel.org
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181009204424.21462-1-lyude@redhat.com
(cherry picked from commit b5d29843d8)
Fixes: e96550956f ("drm/atomic_helper: Disallow new modesets on unregistered connectors")
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
With the exception of modesets which would switch the DPMS state of a
connector from on to off, we want to make sure that we disallow all
modesets which would result in enabling a new monitor or a new mode
configuration on a monitor if the connector for the display in question
is no longer registered. This allows us to stop userspace from trying to
enable new displays on connectors for an MST topology that were just
removed from the system, without preventing userspace from disabling
DPMS on those connectors.
Changes since v5:
- Fix typo in comment, nothing else
Signed-off-by: Lyude Paul <lyude@redhat.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: stable@vger.kernel.org
Link: https://patchwork.freedesktop.org/patch/msgid/20181008232437.5571-2-lyude@redhat.com
(cherry picked from commit 4d80273976)
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
- Fix GPU hang on MacBook2,1 when booting in EFI mode (Bugzilla #105637)
- Fix garbled console on Y tiled BIOS framebuffer configs (Bugzilla #108264)
- Fix black screen on certain eDP panels eg. Dell XPS 9350 (Bugzilla #107489 and #105338)
- MST fixes that Rodrigo dropped from drm-intel-fixes and bunch of Icelake fixes
- Then assorted proactive code fixes caught by CI or developers
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181018165725.GA2281@jlahtine-desk.ger.corp.intel.com
- Fix use of freed memory in drm_mode_setcrtc.
- Reject pixel format changing requests in fb helper.
- Add 6 bpc quirk for HP Pavilion 15-n233sl
- Fix VSDB yCBCr420 Deep Color mode bit definitions
-----BEGIN PGP SIGNATURE-----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=73wn
-----END PGP SIGNATURE-----
Merge tag 'drm-misc-fixes-2018-10-18' of git://anongit.freedesktop.org/drm/drm-misc into drm-fixes
drm-misc-fixes for v4.19:
- Fix use of freed memory in drm_mode_setcrtc.
- Reject pixel format changing requests in fb helper.
- Add 6 bpc quirk for HP Pavilion 15-n233sl
- Fix VSDB yCBCr420 Deep Color mode bit definitions
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/647fe5d0-4ec5-57cc-9f23-a4836b29e278@linux.intel.com
This fixes a general protection fault, caused by accessing the contents
of a flip_done completion object that has already been freed. It occurs
due to the preemption of a non-blocking commit worker thread W by
another commit thread X. X continues to clear its atomic state at the
end, destroying the CRTC commit object that W still needs. Switching
back to W and accessing the commit objects then leads to bad results.
Worker W becomes preemptable when waiting for flip_done to complete. At
this point, a frequently occurring commit thread X can take over. Here's
an example where W is a worker thread that flips on both CRTCs, and X
does a legacy cursor update on both CRTCs:
...
1. W does flip work
2. W runs commit_hw_done()
3. W waits for flip_done on CRTC 1
4. > flip_done for CRTC 1 completes
5. W finishes waiting for CRTC 1
6. W waits for flip_done on CRTC 2
7. > Preempted by X
8. > flip_done for CRTC 2 completes
9. X atomic_check: hw_done and flip_done are complete on all CRTCs
10. X updates cursor on both CRTCs
11. X destroys atomic state
12. X done
13. > Switch back to W
14. W waits for flip_done on CRTC 2
15. W raises general protection fault
The error looks like so:
general protection fault: 0000 [#1] PREEMPT SMP PTI
**snip**
Call Trace:
lock_acquire+0xa2/0x1b0
_raw_spin_lock_irq+0x39/0x70
wait_for_completion_timeout+0x31/0x130
drm_atomic_helper_wait_for_flip_done+0x64/0x90 [drm_kms_helper]
amdgpu_dm_atomic_commit_tail+0xcae/0xdd0 [amdgpu]
commit_tail+0x3d/0x70 [drm_kms_helper]
process_one_work+0x212/0x650
worker_thread+0x49/0x420
kthread+0xfb/0x130
ret_from_fork+0x3a/0x50
Modules linked in: x86_pkg_temp_thermal amdgpu(O) chash(O)
gpu_sched(O) drm_kms_helper(O) syscopyarea sysfillrect sysimgblt
fb_sys_fops ttm(O) drm(O)
Note that i915 has this issue masked, since hw_done is signaled after
waiting for flip_done. Doing so will block the cursor update from
happening until hw_done is signaled, preventing the cursor commit from
destroying the state.
v2: The reference on the commit object needs to be obtained before
hw_done() is signaled, since that's the point where another commit
is allowed to modify the state. Assuming that the
new_crtc_state->commit object still exists within flip_done() is
incorrect.
Fix by getting a reference in setup_commit(), and releasing it
during default_clear().
Signed-off-by: Leo Li <sunpeng.li@amd.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1539611200-6184-1-git-send-email-sunpeng.li@amd.com
Since when it was introduced we forgot to add
this case so ICL was using a wrong signal_levels
as reference.
Fixes: fb5c8e9d43 ("drm/i915/icl: Implement voltage swing programming sequence for Combo PHY DDI")
Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181017215652.26841-1-rodrigo.vivi@intel.com
(cherry picked from commit 61cdfb9e19)
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
DDI/TC clock-off bits are not equally distanced. TC1-3 bits are
from offset 12 & TC4 is at offset 21.
Create a function to choose correct clk-off bit.
v2: Add fixes tag (Lucas)
Fixes: c27e917e2b ("drm/i915/icl: add basic support for the ICL clocks")
Signed-off-by: Mahesh Kumar <mahesh1.kumar@intel.com>
Signed-off-by: Vandita Kulkarni <vandita.kulkarni@intel.com>
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181016023752.9285-1-lucas.demarchi@intel.com
(cherry picked from commit bb1c7edc6d)
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
This patch creates a function/wrapper to check if port is combophy port
instead of explicitly comparing ports.
Changes since V1:
- keep all intel_port_is_* helper together (Lucas)
Signed-off-by: Mahesh Kumar <mahesh1.kumar@intel.com>
Cc: Madhav Chauhan <madhav.chauhan@intel.com>
Cc: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181004085043.10154-1-mahesh1.kumar@intel.com
(cherry picked from commit 176597a12d)
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Hans de Goede <hdegoede@redhat.com>
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEfxcpfMSgdnQMs+QqlvcN/ahKBwoFAlvHll4ACgkQlvcN/ahK
Bwq+Bwf5AbcQDTCun9Qi1HGLxEJZJ/3CMY0PumrDf/U0qyLOs96GbwBJfG8orRpM
Fdyr91cQ0vWeMT3IvcHSj8lPhRRwSbzrLLYFZxoE9JLIaRzRovoavzXQH3IXZ6L0
MxO2t8ZhXlF9bM8dyrHHG7Q8OHdTjaoecTardtBn061cPXXQj4bhJxeCnIbjvMxv
Z4Uhq6vECz/X/xLifSb8Aag8riU0dsq0nqbMCU307xLiGW3Sg1vALcSgyMOlaHJq
iNVwG3rlDa0+6yAfEI1rGf3vy0zb5TohyC2b4934GRMmF55lgnu967npZeMRxKNU
yke98hm9T1b5xEMFXrfv94mQbYWisQ==
=+RQz
-----END PGP SIGNATURE-----
Merge tag 'drm-misc-next-fixes-2018-10-17' of git://anongit.freedesktop.org/drm/drm-misc into drm-next
- Add quirk to fix orientation of Acer One 10 (S1003) panel (Hans)
Cc: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Sean Paul <sean@poorly.run>
Link: https://patchwork.freedesktop.org/patch/msgid/20181017200741.GA240649@art_vandelay
If BIOS configured a Y tiled FB we failed to set up the backing object
tiling accordingly, leading to a lack of GT fence installed and a
garbled console.
The problem was bisected to
commit 011f22eb54 ("drm/i915: Do NOT skip the first 4k of stolen memory for pre-allocated buffers v2")
but it just revealed a pre-existing issue.
Kudos to Ville who suspected a missing fence looking at the corruption
on the screen.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: <ronald@innovation.ch>
Cc: <stable@vger.kernel.org>
Reported-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reported-by: <ronald@innovation.ch>
Tested-by: <ronald@innovation.ch>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=108264
Fixes: bc8d7dffac ("drm/i915/skl: Provide a Skylake version of get_plane_config()")
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181016160011.28347-1-imre.deak@intel.com
(cherry picked from commit 914a4fd8cd)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
For mmap-exhaustion, we deliberately put the system under a large amount
of pressure to ensure that we are able to reap mmap-offsets from dead
objects. If background activity does that reaping for us, that defeats
the purpose of the test and in some cases will fail our sanity checks
(because of the fake activity we use to prevent the idle worker).
Fixes: 932cac10c8 ("drm/i915/selftests: Prevent background reaping of acti
ve objects")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Matthew Auld <matthew.auld@intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181011103748.18387-1-chris@chris-wilson.co.uk
(cherry picked from commit 0b4bf7ca9b)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
This patch fixes the original commit c0cfb10d9e ("drm/i915/edp:
Do not do link training fallback or prune modes on EDP") that causes
a blank screen in case of certain eDP panels (Eg: seen on Dell XPS13 9350)
where first link training fails and a retraining is required by falling
back to lower link rate/lane count.
In case of some panels they advertise higher link rate/lane count
than whats required for supporting the panel's native mode.
But we always link train at highest link rate/lane count for eDP
and if that fails we can still fallback to lower link rate/lane count
as long as the fallback link BW still fits the native mode to avoid
pruning the panel's native mode yet retraining at fallback values
to recover from a blank screen.
v3:
* Add const for fixed_mode (Ville)
v2:
* Send uevent if link failure on eDP unconditionally
Fixes: c0cfb10d9e ("drm/i915/edp: Do not do link training fallback or prune modes on EDP")
Cc: Clinton Taylor <clinton.a.taylor@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Cc: <stable@vger.kernel.org> # v4.17+
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=107489
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=105338
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Tested-by: Alexander Wilson <alexander.wilson@ncf.edu>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181009212804.702-1-manasi.d.navare@intel.com
(cherry picked from commit 1e712535c5)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Currently, i915 appears to rely on blocking modesets on
no-longer-present MSTB ports by simply returning NULL for
->best_encoder(), which in turn causes any new atomic commits that don't
disable the CRTC to fail. This is wrong however, since we still want to
allow userspace to disable CRTCs on no-longer-present MSTB ports by
changing the DPMS state to off and this still requires that we retrieve
an encoder.
So, fix this by always returning a valid encoder regardless of the state
of the MST port.
Changes since v1:
- Remove mst atomic helper, since this got replaced with a much simpler
solution
Signed-off-by: Lyude Paul <lyude@redhat.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: stable@vger.kernel.org
Link: https://patchwork.freedesktop.org/patch/msgid/20181008232437.5571-6-lyude@redhat.com
(cherry picked from commit a9f9ca33d1)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Since we need to be able to allow DPMS on->off prop changes after an MST
port has disappeared from the system, we need to be able to make sure we
can compute a config for the resulting atomic commit. Currently this is
impossible when the port has disappeared, since the VCPI slot searching
we try to do in intel_dp_mst_compute_config() will fail with -EINVAL.
Since the only commits we want to allow on no-longer-present MST ports
are ones that shut off display hardware, we already know that no VCPI
allocations are needed. So, hardcode the VCPI slot count to 0 when
intel_dp_mst_compute_config() is called on an MST port that's gone.
Changes since V4:
- Don't use mst_port_gone at all, just check whether or not the drm
connector is registered - Daniel Vetter
Signed-off-by: Lyude Paul <lyude@redhat.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: stable@vger.kernel.org
Link: https://patchwork.freedesktop.org/patch/msgid/20181008232437.5571-5-lyude@redhat.com
(cherry picked from commit f67207d78c)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Currently we set intel_connector->mst_port to NULL to signify that the
MST port has been removed from the system so that we can prevent further
action on the port such as connector probes, mode probing, etc.
However, we're going to need access to intel_connector->mst_port in
order to fixup ->best_encoder() so that it can always return the correct
encoder for an MST port to prevent legacy DPMS prop changes from
failing. This should be safe, so instead keep intel_connector->mst_port
always set and instead just check the status of
drm_connector->regustered to signify whether or not the connector has
disappeared from the system.
Changes since v2:
- Add a comment to mst_port_gone (Jani Nikula)
- Change mst_port_gone to a u8 instead of a bool, per the kernel bot.
Apparently bool is discouraged in structs these days
Changes since v4:
- Don't use mst_port_gone at all! Just check if the connector is
registered or not - Daniel Vetter
Signed-off-by: Lyude Paul <lyude@redhat.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: stable@vger.kernel.org
Link: https://patchwork.freedesktop.org/patch/msgid/20181008232437.5571-4-lyude@redhat.com
(cherry picked from commit 6ed5bb1fba)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Before we can reset the seqno, we have to be sure the engines are idle.
In debugfs/i915_drop_caches_set, we do wait_for_idle but allow ourselves
to be interrupted. We should only proceed to reset the seqno then if we
were not interrupted, and so also avoid overwriting the error status.
References: https://bugs.freedesktop.org/show_bug.cgi?id=108133
Fixes: 6b048706f4 ("drm/i915: Forcibly flush unwanted requests in drop-caches")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181004082119.24970-1-chris@chris-wilson.co.uk
(cherry picked from commit 88a83f3c2d)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
When we decide that a plane is attached to the wrong pipe we try
to turn off said plane. However we are passing around the crtc we
think that the plane is supposed to be using rather than the crtc
it is currently using. That doesn't work all that well because
we may have to do vblank waits etc. and the other pipe might
not even be enabled here. So let's pass the plane's current crtc to
intel_plane_disable_noatomic() so that it can its job correctly.
To do that semi-cleanly we also have to change the plane readout
to record the plane's visibility into the bitmasks of the crtc
where the plane is currently enabled rather than to the crtc
we want to use for the plane.
One caveat here is that our active_planes bitmask will get confused
if both planes are enabled on the same pipe. Fortunately we can use
plane_mask to reconstruct active_planes sufficiently since
plane_mask still has the same meaning (is the plane visible?)
during readout. We also have to do the same during the initial
plane readout as the second plane could clear the active_planes
bit the first plane had already set.
v2: Rely on fixup_active_planes() to populate active_planes fully (Daniel)
Add Daniel's proposed comment to better document why we do this
Drop the redundant intel_set_plane_visible() call
Cc: stable@vger.kernel.org # fcba862e8428 drm/i915: Have plane->get_hw_state() return the current pipe
Cc: stable@vger.kernel.org
Cc: Dennis <dennis.nezic@utoronto.ca>
Cc: Daniel Vetter <daniel@ffwll.ch>
Tested-by: Dennis <dennis.nezic@utoronto.ca>
Tested-by: Peter Nowee <peter.nowee@gmail.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=105637
Fixes: b1e01595a6 ("drm/i915: Redo plane sanitation during readout")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181003145017.4527-1-ville.syrjala@linux.intel.com
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
(cherry picked from commit 62358aa4ee)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Plane sanitation needs vblank interrupts (on account of CxSR disable).
So let's restore vblank interrupts earlier.
v2: Make it actually build
v3: Add comment to explain why we need this (Daniel)
Cc: stable@vger.kernel.org
Cc: Dennis <dennis.nezic@utoronto.ca>
Tested-by: Dennis <dennis.nezic@utoronto.ca>
Tested-by: Peter Nowee <peter.nowee@gmail.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=105637
Fixes: b1e01595a6 ("drm/i915: Redo plane sanitation during readout")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20181003144951.4397-1-ville.syrjala@linux.intel.com
(cherry picked from commit 68bc30deac)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
commit 4e0b83a567 ("drm/i915: Extract per-platform plane->check()
functions") removed the plane max stride check for sprite planes.
I was going to add it back when introducing GTT remapping for the
display, but after further thought it seems better to re-introduce
it separately.
So let's add the max stride check back. And let's do it in a nicer
form than what we had before and do it for all plane types (easy
now that we have the ->max_stride() plane vfunc).
Only sprite planes really need this for now since primary planes
are capable of scanning out the current max fb size we allow, and
cursors have more stringent stride checks elsewhere.
Cc: José Roberto de Souza <jose.souza@intel.com>
Fixes: 4e0b83a567 ("drm/i915: Extract per-platform plane->check() functions")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180918140243.12207-1-ville.syrjala@linux.intel.com
Reviewed-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
(cherry picked from commit fc3fed5d29)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
ret_code should be initialized with 0. The check of read/write
ptr should be activate when UVD_POWER_STATUS_TILES is off.
Signed-off-by: James Zhu <James.Zhu@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The Acer One 10 uses a clamshell design with a detachable keyboard.
As such in normal operating mode, with the keyboard attach the device
is in landscape mode (and the Acer logo at boot also shows in landscape
mode).
But the device uses a portrait screen rotated 90 degrees (sigh). This
commit adds a quirk for this device so that we shown the fbcon the
right way up and that we hint userspace to also show e.g. plymouth and
gdm the right way up.
Cc: stable@vger.kernel.org
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181012101610.29100-1-hdegoede@redhat.com
The error handling is wrong and "ent" could be NULL we when dereference
it to get "ent->d_inode".
The thing is that normally debugfs_create_file() is not supposed to
require (or have) any error handling. That function does return error
pointers if debugfs is turned off but we know it's enable here. When
it's enabled, then it returns NULL on error.
So what I did was I stripped out all the error handling except around
the i_size_write(). I could have just used a NULL check instead of an
IS_ERR_OR_NULL() but I figured this was more clear because that way you
don't have to look at the surrounding code to see whether debugfs is
enabled or not.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Update the PPtable structure to fit the latest SMC firmware.
Signed-off-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Feifei Xu <Feifei.Xu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
PPTABLE structure is stretched to add I2C controller
configuration. Hold on the PPTABLE_V20_SMU_VERSION bump
until the VBIOS is ready.
Signed-off-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Feifei Xu <Feifei.Xu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
fix a typo in for loop: i->j
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Rex Zhu <Rex.Zhu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
[Why]
A loop inside of build_evenly_distributed_points function that traverse through
the array of points become an infinite loop when m_GammaUpdates does not
get assigned to any value.
[How]
In DMColor, clear m_gammaIsValid bit just before writting all Zeromem for
m_GammaUpdates, to prevent calling build_evenly_distributed_points
before m_GammaUpdates gets assigned to some value.
Signed-off-by: Su Sung Chung <Su.Chung@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Commit b24413180f added
"SPDX-License-Identifier: GPL-2.0" to files which previously had no
license, change this to MIT for radeon matching the license text of the
other radeon files.
Signed-off-by: Jonathan Gray <jsg@jsg.id.au>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Commit b24413180f
'License cleanup: add SPDX GPL-2.0 license identifier to files with no license'
incorrectly added "SPDX-License-Identifier: GPL-2.0" to a file with MIT
license text. Change the SPDX identifier to match the license text.
Signed-off-by: Jonathan Gray <jsg@jsg.id.au>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Update Static Power Gate mode UVD status clear
Signed-off-by: James Zhu <James.Zhu@amd.com>
Acked-by: Leo Liu <leo.liu@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Set VCPU busy after gate power during vcn Static Power Gate start
Signed-off-by: James Zhu <James.Zhu@amd.com>
Acked-by: Leo Liu <leo.liu@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Apply new UMC enable for VNC Dynamic Power Gate mode
Signed-off-by: James Zhu <James.Zhu@amd.com>
Acked-by: Leo Liu <leo.liu@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Remove Sitatic Power Gate mode unused steps during vcn start
Signed-off-by: James Zhu <James.Zhu@amd.com>
Acked-by: Leo Liu <leo.liu@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add Static Power Gate mode Register XX check
Signed-off-by: James Zhu <James.Zhu@amd.com>
Acked-by: Leo Liu <leo.liu@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Move Static Power Gate mode mc resume after MPC control
Signed-off-by: James Zhu <James.Zhu@amd.com>
Acked-by: Leo Liu <leo.liu@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Update Static Power Gate mode VCN global tiling
Signed-off-by: James Zhu <James.Zhu@amd.com>
Acked-by: Leo Liu <leo.liu@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Update Static Power Gate mode VCN memory control
Signed-off-by: James Zhu <James.Zhu@amd.com>
Acked-by: Leo Liu <leo.liu@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Apply new UMC enable for VNC Dynamic Power Gate mode start
Signed-off-by: James Zhu <James.Zhu@amd.com>
Acked-by: Leo Liu <leo.liu@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Remove Dynamic Power Gate mode unused steps during VCN start
Signed-off-by: James Zhu <James.Zhu@amd.com>
Acked-by: Leo Liu <leo.liu@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add Dynamic Power Gate mode Register XX check
Signed-off-by: James Zhu <James.Zhu@amd.com>
Acked-by: Leo Liu <leo.liu@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Update Dynamic Power Gate mode VCN global tiling registers
Signed-off-by: James Zhu <James.Zhu@amd.com>
Acked-by: Leo Liu <leo.liu@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Update Dynamic Power Gate mode VCN memory control
Signed-off-by: James Zhu <James.Zhu@amd.com>
Acked-by: Leo Liu <leo.liu@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Reduce unnecessary local variable.
Signed-off-by: James Zhu <James.Zhu@amd.com>
Acked-by: Leo Liu <leo.liu@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add ring write/read pointer check for VCN dynamic power gate mode
stop,to make sure that no job is left in ring before turn off DPG mode.
Signed-off-by: James Zhu <James.Zhu@amd.com>
Acked-by: Leo Liu <leo.liu@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Update latest static power gate mode stop function for VCN
Signed-off-by: James Zhu <James.Zhu@amd.com>
Acked-by: Leo Liu <leo.liu@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Update latest UVD_MPC register for VCN. Use defined
macro to replace value for readability.
Signed-off-by: James Zhu <James.Zhu@amd.com>
Acked-by: Leo Liu <leo.liu@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add new register offset/mask for VCN to support
latest VCN implementation.
Signed-off-by: James Zhu <James.Zhu@amd.com>
Acked-by: Leo Liu <leo.liu@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY] dp debugfs file does not exist for eDP under
/sys/kernel/debug/dri/0/eDP-1. the root is phy debugfs
is created for dp connector only.
[HOW] for eDP connector, create phy debugfs too.
Signed-off-by: Hersen Wu <hersenxs.wu@amd.com>
Reviewed-by: David Francis <David.Francis@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
For sriov, when first run windows guest, then run linux guest, the gds
vmid0 size will be reset to 0 by windows guest. So if the value has been
reset to 0, then set the value to the default value in linux guest.
v2:
Fixed value instead of reading mmGDS_VMID0_SIZE.
v3:
Set the default value of the switch.
Signed-off-by: Emily Deng <Emily.Deng@amd.com>
Reviewed-by: Junwei Zhang <Jerry.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
We need to make sure that we don't race between job completion and
timeout.
v2: put revert label after calling the handling manually
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Nayan Deshmukh <nayan26deshmukh@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cleanup starting the timeout a bit.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Nayan Deshmukh <nayan26deshmukh@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Give user some hints when the power profile setting is not supported.
Signed-off-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Correctly translate the power profile specified by user to workload
type accepted by SMU fw.
Signed-off-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
-----BEGIN PGP SIGNATURE-----
iQIcBAABAgAGBQJbwDfFAAoJEAx081l5xIa+w1UP/2r/3PaJoqy/O7kqr9rH44PY
TNCFfLlyhAtF/iwXGYockl2eOnGefIX10yhB1TKp6vcIkmXDwyAfMLs5AOrs8u2R
x/O8OslMvXsaXq1tPTD9EvEtl380RtXnFgDxxXSI1gpUBPaqzEFsTGKjfyOMcyO4
/jEg2LGStg1lENHTrDyxuxHInjd2JoHRS4HBT4By2oVP3JZAFgk5MMpW6ejIwGgm
Xi1uBwfEw3ZWqenTYXl2aNzApRH3175G96jZVW7CNPXgR4wFtgcE3HRlN1ZUxe0V
QjBrKrZCx1UB3EDKKZXnrqTYYywqh6SjJR9gZaKJOlM5lI+lYGb3r9oyM0YtcI9+
cdMA2TLlHiy/oACjLgce9PtwrbuU6uQdGaX3mMOl+E+tLWMT0om+8zZLdGRxOh7S
WyFTLr/ekTYY2MY4mMw1d+yZuMnhDExZtXLDJqHo5F01BMU7r6PX8mtQOTq6yik1
BY+0mqkbsieUyNZyiPa+rRcVddqd8BVNjU5Fs2MA7jQ1E2EALHvGlKj2D4pxqrvZ
8XgF7hUA7/h5Kt8glEIuebz/6jpSpa+QM7BgyriVGd/6Um0iEKzQxxzZDGEAr/p6
C3vIDLMCKNwd/8AmwFipNXrBCzjiTOL00WHXw+CF1nuQoF3Q4oauMOQe4kSc7arl
g+CoKv0dH4dO9eXHGgJa
=8MHk
-----END PGP SIGNATURE-----
Merge tag 'drm-fixes-2018-10-12-1' of git://anongit.freedesktop.org/drm/drm
Dave writes:
"drm fixes for 4.19-rc8
single nouveau runtime reference and mst change"
* tag 'drm-fixes-2018-10-12-1' of git://anongit.freedesktop.org/drm/drm:
drm/nouveau/drm/nouveau: Grab runtime PM ref in nv50_mstc_detect()
Add a new list.h helper for doing bulk updates. Used by ttm.
- Fixes for display underflow on VI APUs at 4K with UVD running
- Endian fixes for powerplay on vega
- DC fixes for interlaced video
- Vega20 powerplay fixes
- RV/RV2/PCO powerplay fixes
- Fix for spurious ACPI events on HG laptops
- Fix a memory leak in DC on driver unload
- Fixes for manual fan control mode switching
- Suspend/resume robustness fixes
- Fix display handling on RV2
- VCN fixes for DPG on PCO
- Misc code cleanups and warning fixes
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Alex Deucher <alexdeucher@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181011014739.3117-1-alexander.deucher@amd.com
- Add Maxime to drm-misc maintainer group (Sean)
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Sean Paul <sean@poorly.run>
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEfxcpfMSgdnQMs+QqlvcN/ahKBwoFAlu+YzwACgkQlvcN/ahK
BwrmCwf/QIjDH5jqxt/QPYphNBEKTbAbLRZoN4QM7SZ+asyB+qUKmfrEvgy+dy+e
vNKgm/iYdQs9s/YsOjiMqu50C5ZOyqCvlmGsTVyB0Bssn7TDcgDauXKKd54h/FsC
c63IQzQtcslrUTk2aNrCdU3n4X8FcRP4dRG2u5RuHZuE1z97Rjf0YwWjuTavzOig
M3OWlRzvIpT5e2M6k5mjSkRGx7ezLfdwkjxBKhroe6hjgInx5qg8ZCbSHDMfMlSO
YXYHSStl7DiNAIesUaoA3p7tIrNH+KZ1XqzYqvILkvmze8cssRWeQZEgs+mxSxS8
NSqnoLs0BUWcsyhfowBJpETb8e+w0g==
=7V8f
-----END PGP SIGNATURE-----
Merge tag 'drm-misc-next-fixes-2018-10-10' of git://anongit.freedesktop.org/drm/drm-misc into drm-next
- Fix build failure without CONFIG_DRM_FBDEV_EMULATION (Arnd)
- Add Maxime to drm-misc maintainer group (Sean)
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Sean Paul <sean@poorly.run>
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Sean Paul <sean@poorly.run>
Link: https://patchwork.freedesktop.org/patch/msgid/20181010203951.GA229456@art_vandelay
In case memory resources for *bl_desc* were allocated, release
them before return.
Addresses-Coverity-ID: 1472021 ("Resource leak")
Fixes: 0d46690155 ("drm/nouveau/secboot/acr: Remove VLA usage")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Reviewed-by: John Hubbard <jhubbard@nvidia.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Scrambling is required for supporting any mode over 340MHz. If it's not
supported, reject any modes that would require it.
Signed-off-by: Ilia Mirkin <imirkin@alum.mit.edu>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
When SCDC is supported, make sure that we configure the GPU and monitor
to the same parameters.
Signed-off-by: Ilia Mirkin <imirkin@alum.mit.edu>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
The register programmed by the clock method needs to contain a different
setting for the link speed as well as special divider settings.
Signed-off-by: Ilia Mirkin <imirkin@alum.mit.edu>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
High pixel clocks are required to use a 40 TMDS divider instead of 10,
and even low ones may optionally use scrambling depending on device
support.
Signed-off-by: Ilia Mirkin <imirkin@alum.mit.edu>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Per the documentation in drm_get_pci_dev(), this function is deprecated
and shouldn't be used anymore. As it turns out, we're going to need to
stop using drm_get_pci_dev() anyway in order to allow us to turn off the
card before full system shutdowns, otherwise we'll hit race conditions
with userspace while trying to tear down the card on shutdown.
So, start using drm_dev_get() and drm_dev_put(), and just turn our
load/unload callbacks into open coded init/fini() functions.
Signed-off-by: Lyude Paul <lyude@redhat.com>
Cc: Karol Herbst <kherbst@redhat.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
We forget to free drm in all instances of failure, and additionally also
forget to destroy the master client if the other client fails
initialization.
Signed-off-by: Lyude Paul <lyude@redhat.com>
Cc: Karol Herbst <kherbst@redhat.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
There's literally no difference between any of the backlight init
functions besides the backlight properties they set and the backlight
callbacks that they set, so move all of the duplicated backlight init
code out of there and into nouveau_backlight_init().
This gets rid of a lot of copy pasta!
Changes since v1:
- Some of the pre-refactor callbacks were storing nv_encoder in callback
data for the backlight devices that they registered, as opposed to
nouveau_drm. This got missed and caused some bugs that didn't
originally appear on my setup (NULL kernel derefs) for some reason.
So, fix this by finding the nouveau_encoder in
nouveau_backlight_init(), and using that as the callback data for all
gens instead even if they don't care about the encoder.
Signed-off-by: Lyude Paul <lyude@redhat.com>
Cc: Jeffery Miller <jmiller@neverware.com>
Cc: Karol Herbst <kherbst@redhat.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Still no functional changes.
Signed-off-by: Lyude Paul <lyude@redhat.com>
Reviewed-by: Karol Herbst <kherbst@redhat.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
More consistent with the rest of the codebase, no functional changes
here.
Signed-off-by: Lyude Paul <lyude@redhat.com>
Reviewed-by: Karol Herbst <kherbst@redhat.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Since we're about to use this in nouveau_backlight.c. Same thing as
DRM_WARN_ONCE, DRM_INFO_ONCE, etc...
Signed-off-by: Lyude Paul <lyude@redhat.com>
Cc: Karol Herbst <kherbst@redhat.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Remember, ida IDs start at 0, not 1!
Signed-off-by: Lyude Paul <lyude@redhat.com>
Reviewed-by: Karol Herbst <kherbst@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Move all entries between @first and including @last before @head.
This is useful for LRU lists where a whole block of entries should be
moved to the end of the list.
Used as a band aid in TTM, but better placed in the common list headers.
Acked-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Huang Rui <ray.huang@amd.com>
Reviewed-by: Junwei Zhang <Jerry.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Move copy_array helpers to smu_helper.c and share between
vega12 and vega20.
Reviewed-by: Evan Quan <evan.quan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/gpu/drm/amd/amdgpu/amdgpu_ucode.c: In function 'amdgpu_ucode_init_bo':
drivers/gpu/drm/amd/amdgpu/amdgpu_ucode.c:431:39: warning:
variable 'header' set but not used [-Wunused-but-set-variable]
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/gpu/drm/amd/amdgpu/psp_v11_0.c: In function 'psp_v11_0_ring_stop':
drivers/gpu/drm/amd/amdgpu/psp_v11_0.c:309:19: warning:
variable 'ring' set but not used [-Wunused-but-set-variable]
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/gpu/drm/amd/amdkfd/kfd_device_queue_manager.c: In function 'destroy_queue_cpsch':
drivers/gpu/drm/amd/amdkfd/kfd_device_queue_manager.c:1366:7: warning:
variable 'preempt_all_queues' set but not used [-Wunused-but-set-variable]
It never used since introduct in
commit 992839ad64 ("drm/amdkfd: Add static user-mode queues support")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
There are several switch statements that are missing break statements.
Add missing breaks to handle any fall-throughs corner cases.
Detected by CoverityScan, CID#1457175 ("Missing break in switch")
Fixes: 18aafc59b1 ("drm/amd/powerplay: implement fw related smu interface for iceland.")
Acked-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Currently we return NOTIFY_DONE for any event which we don't think is
ours. However, many laptops will send more then just an ATIF event and
will also send an ACPI_VIDEO_NOTIFY_PROBE event as well. Since we don't
check for this, we return NOTIFY_DONE which causes a keypress for the
ACPI event to be propogated to userspace. This is the equivalent of
someone pressing the display key on a laptop every time there's a
hotplug event.
So, check for ACPI_VIDEO_NOTIFY_PROBE events and suppress keypresses
from them.
Signed-off-by: Lyude Paul <lyude@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
sdma2.4 is only for iceland. For Vi, we don't maintain the
direct fw loading.
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Rex Zhu <Rex.Zhu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Remove the warning message:
"-1 is not supported on VI"
the -1 is the default fw load type, mean auto.
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Rex Zhu <Rex.Zhu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Extract the function of fw loading out of powerplay.
Do fw loading between hw_init/resuem_phase1 and phase2
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Rex Zhu <Rex.Zhu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
We need to do some IPs earlier to deal with ordering issues
similar to how resume is split into two phases.
Will do fw loading via smu/psp between the two phases.
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Rex Zhu <Rex.Zhu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The variable clean is unnecessary.
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Rex Zhu <Rex.Zhu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
1. one is for create/free bo when init/fini
2. one is for fill the bo before fw loading
the ucode bo only need to be created when load driver
and free when driver unload.
when resume/reset, driver only need to re-fill the bo
if the bo is allocated in vram.
Suggested by Christian.
v2: Return error when bo create failed.
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Rex Zhu <Rex.Zhu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fix cg/pg unexpected set in hw init failed case.
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Rex Zhu <Rex.Zhu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
1. only call late_init when hw_init successful,
so check status.hw instand of status.valid in late_init.
2. set status.late_initialized true if late_init was not implemented.
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Rex Zhu <Rex.Zhu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
initialize gfx/sdma before dpm features enabled.
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Rex Zhu <Rex.Zhu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
initialize gfx/sdma before dpm features enabled.
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Rex Zhu <Rex.Zhu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
For the vram_start is 0 case, the gart range will be from 0x0000FFFF00000000
to 0x0000FFFF1FFFFFFF, which will cause the engine hang.
So to avoid the hole, limit the max mc address to AMDGPU_GMC_HOLE_START.:wq
Signed-off-by: Emily Deng <Emily.Deng@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fix CPDMA hang in PRT mode, set CPF_INT_DMA in reg CP_MECx_F32_INT_DIS for Compute and set DISABLE_GFX_HALT_ON_UTCL1_ERROR in reg CP_DEBUG for GFX
Affected ASICs: Vega10 Vega12 Raven
Signed-off-by: Tao Zhou <tao.zhou1@amd.com>
Tested-by: Yukun.Li <yukun1.li@amd.com>
Tested-by: Maciej.Jesionowski <maciej.jesionowski@amd.com>
Acked-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add CP_DEBUG register definition.
Signed-off-by: Tao Zhou <tao.zhou1@amd.com>
Acked-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
RV2 resource is limit to 3 pipes. Limitation should apply to all HW
blocks instead of front pipe.
Signed-off-by: Hersen Wu <hersenxs.wu@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Wrong index for pstate debug test register
[How]
Add correct index value for dcn1_01 in hubbub1_construct()
Signed-off-by: Hersen Wu <hersenxs.wu@amd.com>
Signed-off-by: Roman Li <Roman.Li@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This time mostly further refinement of dpu1+a6xx for sdm845 and
beyond.. and hurray for more negative diffstat :-)
- Misc cleanups and fixes
- GPU preemption optimization
- a6xx perf improvements and clock fixes (ie. lets actually not run at
minimum clks)
- a6xx devfreq/DCVS
- Lots of code cleanup across dpu (Bruce, Jeykumar, Sean)
- Fixed a few crashes on startup relating to dsi (Sean)
- Add cursor support (Sravanthi, Sean)
- Properly free mdss irq on destroy (Jordan)
- Use correct encoder_type when initializing, fixes crash on boot (Stephen)
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Rob Clark <robdclark@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/CAF6AEGsNevCzMiLuNW1EVN6gtP3JZSir6PfnWvnCavSZM+bUFQ@mail.gmail.com
initialize gfx/sdma before dpm features enabled.
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Rex Zhu <Rex.Zhu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
gfx and sdma can be initialized before smu.
Reviewed-by: Evan Quan <evan.quan@amd.com>
Signed-off-by: Rex Zhu <Rex.Zhu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
with this interface, gfx/sdma can be initialized
before smu.
Reviewed-by: Evan Quan <evan.quan@amd.com>
Signed-off-by: Rex Zhu <Rex.Zhu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>