In VIDIOC_S_FREQUENCY command in tuner-core.c, t->freq is set to a new
value before calling set_freq(). This is not necessary, as set_freq() sets
t->freq itself. Moreover, it causes problems with Philips tuners, as they
need to take into consideration difference between previous and new
frequency.
Signed-off-by: Jiri Benc <jbenc@suse.cz>
Cc: Gerd Knorr <kraxel@bytesex.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Attached is a patch to bttv which fixes the following problems.
Affected cards and problems:
~~~~~~~~~~~~~~~~~~~~~~~~
o VP-1020 (200103A) Tuning problems, device detection.
o VP-1020 (DST-MOT) Errors during tuning, device detection fails in a while.
o VP-1030 (DST-CI) Tuning sometimes fails after CI commands.
o VP-2031 (DCT-CI) Tuning problems
The timeout happens before the actual timeout occured in the MCU
on the board, and hence the problems.
Changes: (bttv-i2c.diff)
~~~~~~~~~~~~~~~~~~~~~~~~
o Changed the custom wait queue to wait_event_interruptible_timeout()
- Suggestion by Johannes Stezenbach.
o Fixed the wait queue timeout problem
- This fixes the timeout problem on various cards.
- This problem was visible as many
* Cannot tune to channels, when signal levels are very low.
* app_info does not work in some conditions for CI based cards
- Smaller values worked good for newer cards, but the older cards
suffered, settled down to the worst case values that could happen in any
eventuality.
Signed-off-by: Manu Abraham <manu@kromtek.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch handles the VIDIOC_S_FMT and VIDIOC_G_FMT ioctls for the
saa6752hs.
As only 4 preset video formats are supported (SIF, 1/2D1, 2/3D1, D1), we
compute to which the asked resolution is the nearest and apply it.
Signed-off-by: Frederic Cand <frederic.cand@anevia.com>
Acked-by: Gerd Knorr <kraxel@bytesex.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Another large rollup of various patches from Adrian which make things static
where they were needlessly exported.
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add device table support for the LR214WF card.
The driver will say it's a FlyTV, simply because the name strings are
stored with the card design data, not the device ID data.
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
msp3400 update: Fix and enable "simpler" mode, some other minor fixes.
Signed-off-by: Gerd Knorr <kraxel@bytesex.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
update cx22702 fe driver, add support for using the dvb pll lib, enable
cx22702 support in cx88-dvb.
Signed-off-by: Gerd Knorr <kraxel@bytesex.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fixup error path, without that one the driver kills the machine by oopsing
in the IRQ handler in case the frontend initialization fails.
Signed-off-by: Gerd Knorr <kraxel@bytesex.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This is take two of a patch that should have appeared two days ago, before
yesterday's "remote control" patch for the same card.
This patch sets unconnected GPIO to Output to keep them from floating (just
good driver writing practice, being nice to the chip), and uses GPIO16 to
switch TV vs. FM - this pin switches inputs onto the tuner, as well as the
audio output from the tuner into the 7135 SIF input. Consequently, FM
radio support is being un-commented because it's now working (sort of, see
below).
These two patches get the card almost fully operational; there appears to
be a bug in tda8290.c remaining that puts an offset onto the tuned
frequency in FM radio mode. We're investigating.
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Subject says it ... this card's IR microcontroller design and attachment
are compatible to the company's previous designs, so the patch was as
simple as it gets.
DESC
LifeView FlyTV Platinum FM: GPIO usage
EDESC
From: Peter Missel <peter.missel@onlinehome.de>
This is take two of a patch that should have appeared two days ago, before
yesterday's "remote control" patch for the same card.
This patch sets unconnected GPIO to Output to keep them from floating (just
good driver writing practice, being nice to the chip), and uses GPIO16 to
switch TV vs. FM - this pin switches inputs onto the tuner, as well as the
audio output from the tuner into the 7135 SIF input. Consequently, FM
radio support is being un-commented because it's now working (sort of, see
below).
These two patches get the card almost fully operational; there appears to
be a bug in tda8290.c remaining that puts an offset onto the tuned
frequency in FM radio mode. We're investigating.
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch fix 3 calls to module_param_string() in
driver/media/video/tuner-core.c and drivers/media/video/tda9887.c. In all
three places, the len and the perm parameter was switched.
Signed-off-by: Bert Wesarg <wesarg@informatik.uni-halle.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Here are fixes for drivers/media.
Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
)
From: Johannes Stezenbach <js@linuxtv.org>
Fix http://bugme.osdl.org/show_bug.cgi?id=4395.
Patch by Manu Abraham and Gerd Knorr:
Remove redundant bttv_reset_audio() which caused the computer to freeze
with some bt8xx based DVB cards when loading the bttv driver.
Signed-off-by: Johannes Stezenbach <js@linuxtv.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.
Let it rip!
