On some arm-based platforms, we need to configure platform specific
parameters by device tree node and also define our node as a child
node of parent SDIO host controller.
This patch parses these parameters from device tree. It includes
calibration data download to firmware, wakeup pin configured to firmware,
and soc specific wake up gpio, which will be set as wakeup interrupt pin.
Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
In some case, the btmrvl_sdio firmware would fail to active within the
polling time. Increase the polling interval to 100 msec to fix the
issue.
Signed-off-by: Wei-Ning Huang <wnhuang@chromium.org>
Signed-off-by: Wei-Ning Huang <wnhuang@google.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Usually when driver sends data to firmware it receives TX_DONE
(DN_LD_HOST_INT_STATUS) interrupt from firmware right away.
It's also observed that some times the fireware could delay
sending DN_LD_HOST_INT_STATUS interrupt. If driver sends data to
firmware during suspend processing and the TX_DONE interrupt is
delayed, it may come back at wrong time when SDIO host driver is
in the middle of suspending.
Block any data from stack while suspending. Also skip sending
data that are already in driver tx_queue.
Don't purge the skb queue on suspend to avoid intermittent music
after system resumes from S3.
Signed-off-by: Chin-Ran Lo <crlo@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The new hci_skb_pkt_* wrappers are mainly intented for drivers to
require less knowledge about bt_cb(sbk) handling. So after converting
the core packet handling, convert all drivers.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
NOT NULL comparison modified to be readable, reported
by checkpatch.
Signed-off-by: Prasanna Karthik <mkarthi3@visteon.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch adds support for Marvell's new chipset SD8997.
Register offsets and supported feature flags are updated.
Signed-off-by: Zhaoyang Liu <liuzy@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Coding style fix, extra spaces are removed to make casting
consistent.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
First firmware dump attempt from user works fine, but firmware goes
into bad state after this. Subsequent attempts fails.
As required by the firmware dump implementation, this change writes
FW_DUMP_READ_DONE value to dump ctrl register to address this issue.
Signed-off-by: Nachiket Kukade <kukaden@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This change ensures we will get driver name as 'btmrvl_sdio'
in udev event.
Signed-off-by: Shengzhen Li <szli@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
We will not release sdio bus until firmware is completely
downloaded and becomes ready. Our 8887 A2 chip can have
separate firmware images for WLAN and bluetooth. This
patch fixes an issue observed when both drivers
simultaneously try to download respective firmwares.
Signed-off-by: Aniket Nagarnaik <aniketn@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch fixes a compile warnning "dump_num maybe used uninitialized in
this function".
Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When driver is loaded, it is important to know if FW was already
active or it is freshly downloaded. This patch increases the
priority of the message.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This flag will be set in unload path to make sure that we skip
sending further commands, ignore interrupts and stop main thread
when unload starts.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch adds firmware dump support for marvell
bluetooth chipset. Currently only SD8897 is supported.
This is implemented based on dev_coredump, a new mechnism
introduced in kernel 3.18rc3
Firmware dump can be trigger by
echo 1 > /sys/kernel/debug/bluetooth/hci*/config/fw_dump
and when the dump operation is completed, data can be read by
cat /sys/class/devcoredump/devcd*/data
We have prepared following script to divide fw memory
dump data into multiple files based on memory type.
[root]# cat btmrvl_split_dump_data.sh
#!/bin/bash
# usage: ./btmrvl_split_dump_data.sh dump_data
fw_dump_data=$1
mem_type="ITCM DTCM SQRAM APU CIU ICU MAC EXT7 EXT8 EXT9 EXT10 EXT11 EXT12 EXT13 EXTLAST"
for name in ${mem_type[@]}
do
sed -n "/Start dump $name/,/End dump/p" $fw_dump_data > tmp.$name.log
if [ ! -s tmp.$name.log ]
then
rm -rf tmp.$name.log
else
# Remove the describle info "Start dump" and "End dump"
sed '1d' tmp.$name.log | sed '$d' > /data/$name.log
if [ -s /data/$name.log ]
then
echo "generate /data/$name.log"
else
sed '1d' tmp.$name.log | sed '$d' > /var/$name.log
echo "generate /var/$name.log"
fi
rm -rf tmp.$name.log
fi
done
Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Reviewed-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
BT_INFO/BT_DBG etc. already takes care of adding a newline
An extra newline character inside message is removed in this
patch.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch adds driver support for marvell SD8887 chip.
Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Kevin Gan <ganhy@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Register offsets are different for SD8897 and newer chip SD8887.
We can not have common btmrvl_sdio_card_reg map for them.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
We should suspend hci device and purge remaining data in tx queue
before enabling host sleep in firmware. If any data is sent to
firmware after host sleep is activated, firmware may end up
sending a TX_DONE interrupt to driver. If this interrupt gets
delivered to host while the SDIO host controller is suspending,
it may crash the system.
Conversely, in resume handler, we should resume hci device after
host sleep is de-activated.
Signed-off-by: Chin-Ran Lo <crlo@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
A vendor specific command is sent to firmware during
initialization to enable this feature. This command is for
SD8897 only.
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
For SD8897, CMD52 write_to_clear may have missing interrupts
under certain corner case condition. Use CMD53 read-to-clear
to fix the problem.
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Some ARM versions of Chromebook need to download a new calibration
data from host driver to firmware. They do have EEPROM but still
need a piece of new calibration data in test mode.
The cal-data is platform dependent. It's simpler and more feasible
to use device tree based cal-data instead of configuration file
based cal-data.
This patch remove configuration file based cal-data downloading
and replace it using cal-data from device tree.
When CONFIG_OF is not selected, or the specific property is not
present in the device tree, the calibration downloading will not
happen.
Cc: Mike Frysinger <vapier@chromium.org>
Cc: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: Hyuckjoo Lee <hyuckjoo.lee@samsung.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
To avoid casting skb->dev into hdev, just let the drivers provide
the hdev directly when calling hci_recv_frame() function.
This patch also fixes up all drivers to provide the hdev.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
A text file containing calibration data in hex format can
be provided at following path:
/lib/firmware/mrvl/sd8797_caldata.conf
The data will be downloaded to firmware during initialization.
Reviewed-by: Mike Frysinger <vapier@chromium.org>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: Hyuckjoo Lee <hyuckjoo.lee@samsung.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
There are two places where DIV_ROUND_UP may be used. It makes code a bit
clearer.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Fix to return -ENOMEM in the skb alloc error handling case
instead of 0, as done elsewhere in this function.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The register offsets have been changed in SD8897 and newer chips.
Define a new btmrvl_sdio_card_reg map for SD88xx.
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: Frank Huang <frankh@marvell.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
FW does the synchronization of the different modules during init.
It will report different modules, that it is ready at different times.
The fw download 'winner' will be reported fw ready first. Without this
patch, btmrvl was already continuing before the FW told it too. Probably
on behalf of the 'winner' which then never sees FW ready and times out.
Signed-off-by: Andreas Fenkart <andreas.fenkart@streamunlimited.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
If not winner, driver must release the sdio host lock, so the fw
download can progress. While holding the lock fw download is stalled
and the following error is produced:
[ 235.746015] Bluetooth: FW failed to be active in time!
[ 235.752799] Bluetooth: Downloading firmware failed!
Signed-off-by: Andreas Fenkart <andreas.fenkart@streamunlimited.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
The firmware images are shared with libertas_sdio WiFi chip and used to be
in libertas/ subtree in linux-firmware. As btmrvl_sdio used to look into
the linux-firmware root, it ended up being unsuccessful. Since the
firmware files are not specific to the libertas hardware, they're being
moved into mrvl/ now.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Use standard print specifier and remove print_hex_dump_bytes call.
Makes output more sensible:
...
[18809.401218] 00000000: 0b 00 00 fe 5b fc 01 f2 00 00 00 ....[......
...
would be changed to
...
[18809.401218] Bluetooth: hex: 0b 00 00 fe 5b fc 01 f2 00 00 00
...
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Make code readable by correcting name from buf_block_len to num_blocks
since it represent number of blocks; NOT a length of a block buffer.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Patch shortens locals scope and adds missing braces. This is a diff
between v1 which was applied and v2 of patch "Bluetooth: btmrvl: Do
not send vendor events to bluetooth stack".
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Vendor-specific events shall be processed in driver and not sent
to bluetooth stack where they screw up HCI command countings.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
SD8787 SDIO function 3 (device ID 0x911B) is for Bluetooth AMP.
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Currently debugfs commands "hscfgcmd" and "gpiogap" are provided
for host sleep configuration. But if user doesn't configure host
sleep parameters using these commands, host sleep activation is
failed during suspend (support for suspend and resume handlers is
added in next patch).
Default host sleep configuration is done during driver initialisation
in this patch.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: Gustavo Padovan <gustavo@padovan.org>
release_firmware() deals gracefullt with NULL pointers so there's no
reason to test for one prior to calling the function.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: Gustavo Padovan <gustavo@padovan.org>
The SD8797 firmware image is shared with mwifiex driver.
Whoever gets loaded first will be responsible for firmware
downloading.
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: Frank Huang <frankh@marvell.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
