i915_driver_load adds a write-combining MTRR region for the GTT
aperture to improve memory speeds through the aperture. If
i915_driver_load fails after this, it would not have cleaned up the
MTRR. This shouldn't cause any problems, except for consuming an MTRR
register. Still, it's best to clean up completely in the failure path,
which is easily done by calling mtrr_del if the mtrr was successfully
allocated.
i915_driver_load calls i915_gem_load which register
i915_gem_inactive_shrink. If i915_driver_load fails after calling
i915_gem_load, the shrinker will be left registered. When called, it
will access freed memory and crash. The fix is to unregister the shrinker in the
failure path using code duplicated from i915_driver_unload.
i915_driver_load also has some incorrect gotos in the error cleanup
paths:
* After failing to initialize the GTT (which cannot happen, btw,
intel_gtt_get returns a fixed (non-NULL) value), it tries to
free the uninitialized WC IO mapping. Fixed this by changing the
target from out_iomapfree to out_rmmap
Signed-off-by: Keith Packard <keithp@keithp.com>
Tested-by: Lin Ming <ming.m.lin@intel.com>
As the enable/disable routines will be gain additional complexity in
future patches, it is necessary that all callers do not bypass the
generic interface by calling into the chipset routines directly. to do
this we make the chipset routines static, so there is no choice.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Keith Packard <keithp@keithp.com>
This lets us make the various IRQ functions static and helps avoid
problems like the one fixed in "drm/i915: Use chipset-specific irq
installers" where one of the exported functions was called rather than
the chipset specific version.
This also fixes a UMS-mode bug -- the correct irq functions for IRL
and later chips were only getting loaded in the KMS path.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Keith Packard <keithp@keithp.com>
When auditing the locking in i915_gem.c (for a prospective change which
I then abandoned), I noticed two places where struct_mutex is not held
across GEM object manipulations that would usually require it.
Since one is in initial setup and the other in driver unload, I'm
guessing the mutex is not required for either; but post a patch in case
it is.
Signed-off-by: Hugh Dickins <hughd@google.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Keith Packard <keithp@keithp.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add new interrupt handling functions for Ivy Bridge.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Keith Packard <keithp@keithp.com>
This makes the Ironlake+ code trivial and generally simplifies things.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Keith Packard <keithp@keithp.com>
Set the IRQ handling functions in driver load so they'll just be used
directly, rather than branching over most of the code in the chipset
functions.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Keith Packard <keithp@keithp.com>
The render P-state handling code requires reading from a GT register.
This means that FORCEWAKE must be written to, a resource which is shared
and should be protected by struct_mutex. Hence we can not manipulate
that register from within the interrupt handling and so must delegate
the task to a workqueue.
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Keith Packard <keithp@keithp.com>
If the outputs are active and continuing to access the GATT when we
teardown the PTEs, then there is a potential for us to hang the GPU.
The hang tends to be a PGTBL_ER with either an invalid host access or
an invalid display plane fetch.
v2: Reorder IRQ initialisation to defer until after GEM is setup.
Reported-by: Pekka Enberg <penberg@kernel.org>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Tested-by: Daniel Vetter <daniel.vetter@ffwll.ch> (855GM)
Tested-by: Pekka Enberg <penberg@kernel.org>
# note that this doesn't fix the underlying problem of the
PGTBL_ER and pipe underruns being reported immediately upon
init on his 965GM MacBook
Reported-and-tested-by: Rick Bramley <richard.bramley@hp.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=35635
Reported-and-tested-by: Zdenek Kabelac <zdenek.kabelac@gmail.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=36048
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Added a new function which waits for the ringbuffer space to be equal to
(total - 8). This is the empty condition of the ringbuffer, and
equivalent to head==tail.
Also modified two users of this functionality elsewhere in the code.
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
i915 calls the panic handler function on last close to reset the modes,
however this is a really bad idea for multi-gpu machines, esp shareable
gpus machines. So add a new entry point for the driver to just restore
its own fbcon mode.
v2: move code into fb helper, fix panic code to block mode change on
powered off GPUs.
[airlied: this hits drm core and I wrote it and it was reviewed on intel-gfx
so really I signed it off twice ;-).]
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Dave Airlie <airlied@redhat.com>
On a Thinkpad x61s, I noticed some memory corruption when
plugging/unplugging the external VGA connection. The symptoms are that
4 bytes at the beginning of a page get overwritten by zeroes.
The address of the corruption varies when rebooting the machine, but
stays constant while it's running (so it's possible to repeatedly write
some data and then corrupt it again by plugging the cable).
Further investigation revealed that the corrupted address is
(dev_priv->status_page_dmah->busaddr & 0xffffffff), ie. the beginning of
the hardware status page of the i965 graphics card, cut to 32 bits.
So it seems that for some memory access, the hardware uses only 32 bit
addressing. If the hardware status page is located >4GB, this
corrupts unrelated memory.
Signed-off-by: Jan Niehusmann <jan@gondor.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@kernel.org
Userspace has a legitimate requirement to use a delta that points to
outside of the target bo, and so we need to enable this. (As this is an
abi break, albeit a relaxation of the current restrictions, mark the change
with a new flag.)
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
We had some conversions over to the _PIPE macros, but didn't get
everything. So hide the per-pipe regs with an _ (still used in a few
places for legacy) and add a few _PIPE based macros, then make sure
everyone uses them.
[update: remove usage of non-existent no-op macro]
[update 2: keep modesetting suspend/resume code, update to new reg names]
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
[ickle: stylistic cleanups for checkpatch and taste]
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
A lot of minor tweaks to fix the tracepoints, improve the outputting for
ftrace, and to generally make the tracepoints useful again. It is a start
and enough to begin identifying performance issues and gaps in our
coverage.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Starting with SandyBridge (though possible with earlier hacked BIOSes),
the BIOS may initialise the IGFX as secondary to a discrete GPU. Prior,
it would simply disable the integrated GPU. So we adjust our PCI class
mask to match any DISPLAY_CLASS device.
In such a configuration, the IGFX is not a primary VGA controller and
so should not take part in VGA arbitration, and the error return from
vga_client_register() is expected.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@kernel.org
Move code around and invoke iomem annotation in a few more places in
order to silence sparse. Still a few more iomem annotations to go...
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
As has_gem is unconditionally set to true, the conditional immediately
following that assignment is superfluous.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
We need to track the state of the switch in drivers, so that after s/r
we don't resume the card we've explicitly switched off before. Also
don't allow a userspace open to occur if we've switched the gpu off.
Signed-off-by: Dave Airlie <airlied@redhat.com>
The IPS driver is designed to be able to run detached from i915 and
just not enable GPU turbo in that case, in order to avoid module
dependencies between the two drivers. This means that we don't know
what the load order between the two is going to be, and we had
previously only supported IPS after (optionally) i915, but not i915
after IPS. If the wrong order was chosen, you'd get no GPU turbo, and
something like half the possible graphics performance.
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@kernel.org
The relative-to-general state default is useless as it means having to
rewrite the streaming kernels for each batch. Relative-to-surface is
more useful, as that stream usually needs to be rewritten for each
batch. And absolute addressing mode, vital if you start streaming
state, is also only available by adjusting the register...
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Add frame buffer compression on Sandybridge. The method is similar to
Ironlake, except that two new registers of type GTTMMADR must be written
with the right fence info.
Signed-off-by: Yuanhan Liu <yuanhan.liu@linux.intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Otherwise we can't really fix the abi-braindeadness of forcing
libva to manually wait for rendering when switching rings. Which
in turn makes implementing hw semaphores a pointless exercise
(at least for ironlake).
[Also added the relaxed fencing param to explain the jump in
numbering - relaxed fencing is in -next.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
The bulk of the change is to convert the growing list of rings into an
array so that the relationship between the rings and the semaphore sync
registers can be easily computed.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
This makes the various rings more consistent by removing the anomalous
handing of the rendering ring execbuffer dispatch.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
The GATT is a write-only set of registers, reading from them in the
manner of i915_gtt_to_phys() is supposed to be undefined. However a
simple solution exists as we allocate linear memory from the stolen
area, we can simply add the block offset to the base register. As a
side-effect we recover all the unused stolen GTT entries and so enlarge
our aperture.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
It isn't used for the hangcheck, which does its work right from the
timer trigger, but hangcheck can lead to error state recording, which
is run off of the workqueue.
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
We only ever used the PRB0, neglecting the secondary ring buffers, and
now with the advent of multiple engines with separate ring buffers we
need to excise the anachronisms from our code (and be explicit about
which ring we mean where). This is doubly important in light of the
FORCEWAKE required to read ring buffer registers on SandyBridge.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
If modeset init failed we attempted to unload the module, before we
finished setting it up and so triggered various oopses.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
After switching the MMIO registers to use pci_iomap, remember to dispose
of the mapping with pci_iounmap (for symmetry).
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
So long as we adhere to the fence registers rules for alignment and no
overlaps (including with unfenced accesses to linear memory) and account
for the tiled access in our size allocation, we do not have to allocate
the full fenced region for the object. This allows us to fight the bloat
tiling imposed on pre-i965 chipsets and frees up RAM for real use. [Inside
the GTT we still suffer the additional alignment constraints, so it doesn't
magic allow us to render larger scenes without stalls -- we need the
expanded GTT and fence pipelining to overcome those...]
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Eliminate the racy device unload by embedding a shrinker into each
device. Smaller, simpler code.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Play safe and use the common routines which take care of the cachability
of the memory when setting up the iomapping for the PCI registers.
Whilst they should be cacheable for the current generations, actually
honouring what the device requires is a better long term strategy.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
This is the same value as before, but it just makes the code slightly
more readable to use the local variable than converting the aperture
size into bytes every time.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
At least the part that's currently enabled by the BIOS.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Preparing the ringbuffer for adding new commands can fail (a timeout
whilst waiting for the GPU to catch up and free some space). So check
for any potential error before overwriting HEAD with new commands, and
propagate that error back to the user where possible.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
The ringbuffer keeps a pointer to the parent device, so we can use that
instead of passing around the pointer on the stack.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Based on an original patch by Zhenyu Wang, this initializes the BLT ring for
SandyBridge and enables support for user execbuffers.
Cc: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
... by always initialising the empty ringbuffer it is always then safe
to check whether it is active.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
The time between start of the pixel clock and backlight enable is a basic
panel timing constraint. If the Panel Power On/Off registers are found
to be 0, assume we are booting without VBIOS initialization and set these
registers to something reasonable.
Change-Id: Ibed6cc10d46bf52fd92e0beb25ae3525b5eef99d
Signed-off-by: Bryan Freed <bfreed@chromium.org>
[ickle: rearranged into a separate function to distinguish its role from
simply parsing the VBIOS tables.]
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Freeing the Hardware Status Page was writing to the HWS register in
order to disable the GPU writing to the HWS page. Unfortunately, we were
writing to the mmio register after unmapping the register space, hence
the oops.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
This reverts commit 6939a5aca7.
Daniel Vetter supplied a set of fixes for all the module unload bugs he
could trigger on his machines, so let the fun recommence!
The i915 driver has quite a few module unload bugs, the known ones at
least have fixes that are targeting 2.6.37. However, in order to
maintain a stable kernel, we should prevent this known random memory
corruption following driver unload. This should have very low impact on
normal users who are unlikely to need to unload the i915 driver.
Suggested-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: stable@kernel.org
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
The _DSM method on the integrated graphics device can tell us which
connectors are muxable, so add support for making the call and parsing
out the connector info.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
[ickle: fix compiler warnings for using uninitialized 'result' and
downgrade error message for non-switchable devices]
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
A physically mapped hardware status page is allocated at driver load
time but was never freed. Call the existing code to free this page at
driver unload time on hardware which uses this kind.
Signed-off-by: Keith Packard <keithp@keithp.com>
[ickle: call before tearing down registers on KMS-only path, as pointed
out by Dave Airlie]
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@kernel.org
lockdep spots that the fb_info->lock takes the dev->struct_mutex during
init (due to the device probing) and so we can not hold
dev->struct_mutex when unregistering the framebuffer. Simply reverse the
order of initialisation during cleanup and so do the intel_fbdev_fini()
before the intel_modeset_cleanup.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
The IPS driver needs to know the current power consumption of the GMCH
in order to make decisions about when to increase or decrease the CPU
and/or GPU power envelope. So fix up the divisions to save the results
so the numbers are actually correct (contrary to some earlier comments
and code, these functions do not modify the first argument and use it
for the result).
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@kernel.org
Daniel Vetter pointed out that in this case is would be clearer and
cleaner to use a spinlock instead of a mutex to protect the per-file
request list manipulation. Make it so.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
It's the same code, essentially, so kill all copies safe one unified
version.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Avoid cause latencies in other clients by not taking the global struct
mutex and moving the per-client request manipulation a local per-client
mutex. For example, this allows a compositor to schedule a page-flip
(through X) whilst an OpenGL application is monopolising the GPU.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Suspending (especially hibernating) may take a finite amount of time,
during which a hotplug event may trigger and we will attempt to handle
it with inconsistent state. Disable hotplug polling around suspend and
resume.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=30070
Reported-by: Rui Tiago Matos <tiagomatos@gmail.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Consolidate everything in intel-gtt.c and also kill the export
of intel_max_stolen.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Use the GMBUS interface rather than direct bit banging to grab the EDID
over DDC (and for other forms of auxiliary communication with external
display controllers). The hope is that this method will be much faster
and more reliable than bit banging for fetching EDIDs from buggy monitors
or through switches, though we still preserve the bit banging as a
fallback in case GMBUS fails.
Based on an original patch by Jesse Barnes.
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
create_singlethreaded_workqueue() is being phased out for a new
concurrency managed task infrastructure.
Adapt our workqueue constructor to explicitly create a domain that only
allows the execution of a single task at any time. All the tasks are
expected to require the dev->struct_mutex, so would block concurrency of
other tasks if we allow more than a single i915 task to be run at once.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Use the detection from intel-gtt.ko instead. Hooray!
Also move the stolen mem allocator to the other gtt stuff in dev_prv->mem.
v2: Chris Wilson noted that my error handling was crap. Fix it. He also
said that this fixes a problem on his i845. Indeed, i915_probe_agp
misses a special case for i830/i845 stolen mem detection.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=25476
Cc: stable@kernel.org
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Add a few definitions to it that are already shared and that will
be shared in the future (like the number of stolen entries).
No functional changes in here.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
We do it whilst configuring dev->mode_config, so remove the out-of-place
earlier initialisation.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
We have no idea why we request a SyncFlush via INSTPM at that point in
time -- we certainly never check for its completion...
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
It is recommended that we use the Video BIOS tables that were copied
into the OpRegion during POST when initialising the driver. This saves
us from having to furtle around inside the ROM ourselves and possibly
allows the vBIOS to adjust the tables prior to initialisation.
On some systems, such as the Samsung N210, there is no accessible VBIOS
and the only means of finding the VBT is through the OpRegion.
v2: Rearrange the code so that ASLE is enabled along with ACPI
v3: Enable OpRegion parsing even without ACPI
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Matthew Garrett <mjg@redhat.com>
ums-gem code correctly cancels the retire work (at lastclose time),
kms does not do so. Fix this by canceling the work right after ideling
the gpu.
While staring at the code I noticed that the work function is not
static. Fix this, too.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
When the module unloads, all users should be gone, hence all bo references
held by userspace, too. This should already result in an idle ringbuffer.
Still, be paranoid and idle gem before starting the unload dance.
Also kill the call to i915_gem_lastclose under an if (kms), it's a noop
for kms.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Kill any outstanding unpin_work when destroying the corresponding
crtc. Then flush the workqueue before the gem teardown, in case
any unpin work is still outstanding.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
With kms, interrupts now get disabled in the modesetting cleanup. So
free the error state afterwards, it currently gets allocated in
the interrupt handler.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
hotplug_work is queued by the hotplug interrupt and only either emits
a hotplug uevent or queues a crt poll slow-work. No other locking. So
it's safe to cancel this work _after_ irq's have been turned off. But
before the modesetting objects are destroyed because the hotplug
function accesses them (without locking).
The current code (for kms) only switches irqs off after modesetting
teardown, hence move the irq teardown into the modeset cleanup right
before the crtc cleanup.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
This is the first patch to clean up module unload races due to
outstanding timers/work. Preparatory step: Thou shalt not destroy
the workqueue when new work might still get enqued.
Now error_work gets queued by the hangcheck timer and only (atomically)
reads the chip wedged status. So cancel it right after the hangcheck
timer is killed. But the hangcheck is armed by interrupts, so move
everything after irqs are disabled.
Also change a del_timer to a del_timer_sync in the ums gem code, the
hangcheck timer is self-rearming.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
We were failing when trying to allocate the resource for MMIO of the
MCHBAR because we forgot to specify what type of resource we wanted.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: stable@kernel.org
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
copy_to_user returns the number of bytes remaining to be copied, but we
want to return a negative error code here. These are returned to
userspace.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@kernel.org
So set the coherent dma mask accordingly. This dma mask is only used
for physical objects, so it won't really matter allocation-wise.
Now this never really surfaced because sane 32bit kernels only have 1G
of lowmem. But some eager testers (distros?) still carry around the patch
to adjust lowmem via a kconfig option. And the kernel seems to favour
high allocations on boot-up, hence the overlay blowing up reliably.
Because the patch is tiny and nicely shows how broken gen2 is it's imho
worth to merge despite the fact that mucking around with the lowmem/
highmem division is (no longer) supported.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=28318
Cc: stable@kernel.org
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
* 'drm-core-next' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6: (33 commits)
drm/radeon/kms: fix typo in radeon_compute_pll_gain
drm/radeon/kms: try to detect tv vs monitor for underscan
drm/radeon/kms: fix sideport detection on newer rs880 boards
drm/radeon: fix passing wrong type to gem object create.
drm/radeon/kms: set encoder type to DVI for HDMI on evergreen
drm/radeon/kms: add back missing break in info ioctl
drm/radeon/kms: don't enable MSIs on AGP boards
drm/radeon/kms: fix agp mode setup on cards that use pcie bridges
drm: move dereference below check
drm: fix end of loop test
drm/radeon/kms: rework radeon_dp_detect() logic
drm/radeon/kms: add missing asic callback assignment for evergreen
drm/radeon/kms/DCE3+: switch pads to ddc mode when going i2c
drm/radeon/kms/pm: bail early if nothing's changing
drm/radeon/kms/atom: clean up dig atom handling
drm/radeon/kms: DCE3/4 transmitter fixes
drm/radeon/kms: rework encoder handling
drm/radeon/kms: DCE3/4 AdjustPixelPll updates
drm/radeon: Fix stack data leak
drm/radeon/kms: fix GTT/VRAM overlapping test
...
With the current screwed but its ABI, ioctls for the drm, Linus pointed out that we could allow userspace to specify the allocation size, but we pass it to the driver which then uses it blindly to store a struct. Now if userspace specifies the allocation size as smaller than the driver needs, the driver can possibly overwrite memory.
This patch restructures the driver ioctls so we store the structure size we are expecting, and make sure we allocate at least that size. The copy from/to userspace are still restricted to the size the user specifies, this allows ioctl structs to grow on both sides of the equation.
Up until now we didn't really use the DRM_IOCTL defines in the kernel, so this cleans them up and adds them for nouveau.
v2:
fix nouveau pushbuf arg (thanks to Ben for pointing it out)
Reported-by: Linus Torvalds <torvalds@linuxfoundation.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This is required by the spec, and without this some 3D programs will
hang after resume from RC6 we enable that.
Signed-off-by: Zou Nan hai <nanhai.zou@intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Some BIOSes will claim a large chunk of stolen space. Unless we
reclaim it, our aperture for remapping buffer objects will be
constrained. So clamp the stolen space to 32M and ignore the rest.
Fixes https://bugzilla.kernel.org/show_bug.cgi?id=15469 among others.
Adding the ignored stolen memory back into the general pool using the
memory hotplug code is left as an exercise for the reader.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Simon Farnsworth <simon.farnsworth@onelan.com>
Tested-by: Artem S. Tashkinov <t.artem@mailcity.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
About 0.2W power can be saved on one HP laptop.
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
We should only free the compressed llb if we allocated it in the first
place otherwise we'll panic at unload time.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
* drm-platform:
drm: Make sure the DRM offset matches the CPU
drm: Add __arm defines to DRM
drm: Add support for platform devices to register as DRM devices
drm: Remove drm_resource wrappers
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/anholt/drm-intel:
drm/i915: fix page flip finish vs. prepare on plane B
drm/i915: change default panel fitting mode to preserve aspect ratio
drm/i915: fix uninitialized variable warning in i915_setup_compression()
drm/i915: take struct_mutex in i915_dma_cleanup()
drm/i915: Fix CRT hotplug regression in 2.6.35-rc1
i915: fix ironlake edp panel setup (v4)
drm/i915: don't access FW_BLC_SELF on 965G
drm/i915: Account for space on the ring buffer consumed whilst wrapping.
drm/i915: gen3 page flipping fixes
drm/i915: don't queue flips during a flip pending event
drm/i915: Fix incorrect intel_ring_begin size in BSD ringbuffer.
drm/i915: Turn on 945 self-refresh only if single CRTC is active
drm/i915/gen4: Fix interrupt setup ordering
drm/i915: Use RSEN instead of HTPLG for tfp410 monitor detection.
drm/i915: Move non-phys cursors into the GTT
Revert "drm/i915: Don't enable pipe/plane/VCO early (wait for DPMS on)."
(Included the "fix page flip finish vs. prepare on plane B" patch from
Jesse on top of the pull request from Eric. -- Linus)
Fixes:
drivers/gpu/drm/i915/i915_dma.c: In function ‘i915_setup_compression’:
drivers/gpu/drm/i915/i915_dma.c:1311: error: ‘compressed_llb’ may be used uninitialized in this function
Signed-off-by: Prarit Bhargava <prarit@redhat.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
intel_cleanup_ring_buffer() calls drm_gem_object_unreference() (as
opposed to drm_gem_object_unreference_unlocked()) so it needs to be
called with "struct_mutex" held. If we don't hold the lock, it triggers
a BUG_ON(!mutex_is_locked(&dev->struct_mutex));
I also audited the other places that call intel_cleanup_ring_buffer()
and they all hold the lock so they're OK.
This was introduced in: 8187a2b70e "drm/i915: introduce
intel_ring_buffer structure (V2)" and it's a regression from v2.6.34.
Addresses: https://bugzilla.kernel.org/show_bug.cgi?id=16247
Signed-off-by: Dan Carpenter <error27@gmail.com>
Reported-by: Benny Halevy <bhalevy@panasas.com>
Tested-by: Benny Halevy <bhalevy@panasas.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Gen3 chips have slightly different flip commands, and also contain a bit
that indicates whether a "flip pending" interrupt means the flip has
been queued or has been completed.
So implement support for the gen3 flip command, and make sure we use the
flip pending interrupt correctly depending on the value of ECOSKPD bit
0.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
The previous commit fixes the problem, these commits make sure we actually
fail properly if it happens again.
I've squashed the commits from Chris since they are all fixing one issue.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Dave Airlie <airlied@redhat.com>
* 'drm-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6: (41 commits)
drm/radeon/kms: make sure display hw is disabled when suspending
drm/vmwgfx: Allow userspace to change default layout. Bump minor.
drm/vmwgfx: Fix framebuffer modesetting
drm/vmwgfx: Fix vga save / restore with display topology.
vgaarb: use MIT license
vgaarb: convert pr_devel() to pr_debug()
drm: fix typos in Linux DRM Developer's Guide
drm/radeon/kms/pm: voltage fixes
drm/radeon/kms/pm: radeon_set_power_state fixes
drm/radeon/kms/pm: patch default power state with default clocks/voltages on r6xx+
drm/radeon/kms/pm: enable SetVoltage on r7xx/evergreen
drm/radeon/kms/pm: add support for SetVoltage cmd table (V2)
drm/radeon/kms/evergreen: add initial CS parser
drm/kms: disable/enable poll around switcheroo on/off
drm/nouveau: fixup confusion over which handle the DSM is hanging off.
drm/nouveau: attempt to get bios from ACPI v3
drm/nv50: cast IGP memory location to u64 before shifting
drm/ttm: Fix ttm_page_alloc.c
drm/ttm: Fix cached TTM page allocation.
drm/vmwgfx: Remove some leftover debug messages.
...
This will let userland only try to use the new media decode
functionality when the appropriate kernel is present.
Signed-off-by: Zou Nan hai <nanhai.zou@intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Allow platform devices without PCI resources to be DRM devices.
[airlied: fixup warnings with dev pointers]
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Remove the drm_resource wrappers and directly use the
actual PCI and/or platform functions in their place.
[airlied: fixup nouveau properly to build]
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Reviewed-by: Matt Turner <mattst88@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Pineview with DDR3 memory has different latencies to enable CxSR.
This patch updates CxSR latency table to add Pineview DDR3 latency
configuration. It also adds one flag "is_ddr3" for checking DDR3
setting in MCHBAR.
Cc: Shaohua Li <shaohua.li@intel.com>
Cc: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Li Peng <peng.li@intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Add power monitoring support to the i915 driver for use by the IPS
driver. Export the available power info to the IPS driver through a few
new inter-driver hooks. When used together, the IPS driver and this
patch can significantly increase graphics performance on Ironlake class
chips.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
[anholt: Fixed 32-bit compile. stupid obfuscating div_u64()]
Signed-off-by: Eric Anholt <eric@anholt.net>
The BSD (bit stream decoder) ring is used for accessing the BSD engine
which decodes video bitstream for H.264 and VC1 on G45+. It is
asynchronous with the render ring and has access to separate parts of
the GPU from it, though the render cache is coherent between the two.
Signed-off-by: Zou Nan hai <nanhai.zou@intel.com>
Signed-off-by: Xiang Hai hao <haihao.xiang@intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
The active list and request list move into the ringbuffer structure,
so each can track its active objects in the order they are in that
ring. The flushing list does not, as it doesn't matter which ring
caused data to end up in the render cache. Objects gain a pointer to
the ring they are active on (if any).
Signed-off-by: Zou Nan hai <nanhai.zou@intel.com>
Signed-off-by: Xiang Hai hao <haihao.xiang@intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Introduces a more complete intel_ring_buffer structure with callbacks
for setup and management of a particular ringbuffer, and converts the
render ring buffer consumers to use it.
Signed-off-by: Zou Nan hai <nanhai.zou@intel.com>
Signed-off-by: Xiang Hai hao <haihao.xiang@intel.com>
[anholt: Fixed up whitespace fail and rebased against prep patches]
Signed-off-by: Eric Anholt <eric@anholt.net>
This is preparation for supporting multiple ringbuffers on Ironlake.
The non-copy-and-paste changes are:
- de-staticing functions
- I915_GEM_GPU_DOMAINS moving to i915_drv.h to be used by both files.
- i915_gem_add_request had only half its implementation
copy-and-pasted out of the middle of it.
* anholt/drm-intel-next: (515 commits)
drm/i915: Fix out of tree builds
drm/i915: move fence lru to struct drm_i915_fence_reg
drm/i915: don't allow tiling changes on pinned buffers v2
drm/i915: Be extra careful about A/D matching for multifunction SDVO
drm/i915: Fix DDC bus selection for multifunction SDVO
drm/i915: cleanup mode setting before unmapping registers
drm/i915: Make fbc control wrapper functions
drm/i915: Wait for the GPU whilst shrinking, if truly desperate.
drm/i915: Use spatio-temporal dithering on PCH
[MTD] Remove zero-length files mtdbdi.c and internal.ho
pata_pcmcia / ide-cs: Fix bad hashes for Transcend and kingston IDs
libata: Fix several inaccuracies in developer's guide
slub: Fix bad boundary check in init_kmem_cache_nodes()
raid6: fix recovery performance regression
KEYS: call_sbin_request_key() must write lock keyrings before modifying them
KEYS: Use RCU dereference wrappers in keyring key type code
KEYS: find_keyring_by_name() can gain access to a freed keyring
ALSA: hda: Fix 0 dB for Packard Bell models using Conexant CX20549 (Venice)
ALSA: hda - Add quirk for Dell Inspiron 19T using a Conexant CX20582
ALSA: take tu->qlock with irqs disabled
...
After thinking it over a lot it made more sense for the core to deal with
the output polling especially so it can notify X.
v2: drop plans for fake connector - per Michel's comments - fix X patch sent to xorg-devel, add intel polled/hpd setting, add initial nouveau polled/hpd settings.
v3: add config lock take inside polling, add intel/nouveau poll init/fini calls
v4: config lock was a bit agressive, only needed around connector list reading.
otherwise it could re-enter.
glisse: discard drm_helper_hpd_irq_event
v3: Reviewed-by: Michel Dänzer <michel@daenzer.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Conflicts:
drivers/gpu/drm/i915/i915_dma.c
drivers/gpu/drm/i915/i915_drv.h
drivers/gpu/drm/radeon/r300.c
The BSD ringbuffer support that is landing in this branch
significantly conflicts with the Ironlake PIPE_CONTROL fix on master,
and requires it to be tested successfully anyway.
We'll turn off outputs etc at unload time, so don't unmap the registers
before doing it.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
This keeps the memory manager from complaining when we take it down.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
* drm-fbdev-cleanup:
drm/fb: remove drm_fb_helper_setcolreg
drm/kms/fb: use slow work mechanism for normal hotplug also.
drm/kms/fb: add polling support for when nothing is connected.
drm/kms/fb: provide a 1024x768 fbcon if no outputs found.
drm/kms/fb: separate fbdev connector list from core drm connectors
drm/kms/fb: move to using fb helper crtc grouping instead of core crtc list
drm/fb: fix fbdev object model + cleanup properly.
Conflicts:
drivers/gpu/drm/i915/i915_drv.h
drivers/gpu/drm/nouveau/nouveau_drv.h
* 'anholt/drm-intel-next' of /home/airlied/kernel/drm-next: (48 commits)
agp/intel-gtt: kill previous_size assignments
agp/intel-gtt: kill intel_i830_tlbflush
agp/intel: split out gmch/gtt probe, part 1
agp/intel: kill mutli_gmch_chip
agp/intel: uncoditionally reconfigure driver on resume
agp/intel: split out the GTT support
agp/intel: introduce intel-agp.h header file
drm/i915: Don't touch PORT_HOTPLUG_EN in intel_dp_detect()
drm/i915/pch: Use minimal number of FDI lanes (v2)
drm/i915: Add the support of memory self-refresh on Ironlake
drm/i915: Move Pineview CxSR and watermark code into update_wm hook.
drm/i915: Only save/restore FBC on the platform that supports FBC
drm/i915: Fix the incorrect argument for SDVO SET_TV_format command
drm/i915: Add support of SDVO on Ibexpeak PCH
drm/i915: Don't enable pipe/plane/VCO early (wait for DPMS on).
drm/i915: do not read uninitialized ->dev_private
Revert "drm/i915: Use a dmi quirk to skip a broken SDVO TV output."
drm/i915: implement multifunction SDVO device support
drm/i915: remove unused intel_pipe_get_connector()
drm/i915: remove connector object in old output structure
...
->dev_private at that point is NULL and is initialied only a few lines
later.
Signed-off-by: Luca Tettamanti <kronos.it@gmail.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
PCH is the new name for south bridge from Ironlake/Sandybridge,
which contains most of the display outputs except eDP. This one
adds a probe function to detect current PCH type, and method to
detect Cougarpoint PCH.
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
The fbdev layer in the kms code should act like a consumer of the kms services and avoid having relying on information being store in the kms core structures in order for it to work.
This patch
a) removes the info pointer/psuedo palette from the core drm_framebuffer structure and moves it to the fbdev helper layer, it also removes the core drm keeping a list of kernel kms fbdevs.
b) migrated all the fb helper functions out of the crtc helper file into the fb helper file.
c) pushed the fb probing/hotplug control into the driver
d) makes the surface sizes into a structure for ease of passing
This changes the intel/radeon/nouveau drivers to use the new helper.
Signed-off-by: Dave Airlie <airlied@redhat.com>
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files. percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.
percpu.h -> slab.h dependency is about to be removed. Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability. As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.
http://userweb.kernel.org/~tj/misc/slabh-sweep.py
The script does the followings.
* Scan files for gfp and slab usages and update includes such that
only the necessary includes are there. ie. if only gfp is used,
gfp.h, if slab is used, slab.h.
* When the script inserts a new include, it looks at the include
blocks and try to put the new include such that its order conforms
to its surrounding. It's put in the include block which contains
core kernel includes, in the same order that the rest are ordered -
alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
doesn't seem to be any matching order.
* If the script can't find a place to put a new include (mostly
because the file doesn't have fitting include block), it prints out
an error message indicating which .h file needs to be added to the
file.
The conversion was done in the following steps.
1. The initial automatic conversion of all .c files updated slightly
over 4000 files, deleting around 700 includes and adding ~480 gfp.h
and ~3000 slab.h inclusions. The script emitted errors for ~400
files.
2. Each error was manually checked. Some didn't need the inclusion,
some needed manual addition while adding it to implementation .h or
embedding .c file was more appropriate for others. This step added
inclusions to around 150 files.
3. The script was run again and the output was compared to the edits
from #2 to make sure no file was left behind.
4. Several build tests were done and a couple of problems were fixed.
e.g. lib/decompress_*.c used malloc/free() wrappers around slab
APIs requiring slab.h to be added manually.
5. The script was run on all .h files but without automatically
editing them as sprinkling gfp.h and slab.h inclusions around .h
files could easily lead to inclusion dependency hell. Most gfp.h
inclusion directives were ignored as stuff from gfp.h was usually
wildly available and often used in preprocessor macros. Each
slab.h inclusion directive was examined and added manually as
necessary.
6. percpu.h was updated not to include slab.h.
7. Build test were done on the following configurations and failures
were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my
distributed build env didn't work with gcov compiles) and a few
more options had to be turned off depending on archs to make things
build (like ipr on powerpc/64 which failed due to missing writeq).
* x86 and x86_64 UP and SMP allmodconfig and a custom test config.
* powerpc and powerpc64 SMP allmodconfig
* sparc and sparc64 SMP allmodconfig
* ia64 SMP allmodconfig
* s390 SMP allmodconfig
* alpha SMP allmodconfig
* um on x86_64 SMP allmodconfig
8. percpu.h modifications were reverted so that it could be applied as
a separate patch and serve as bisection point.
Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
We probably don't need it for most of the other driver ioctls as well,
but we explicitly did locking when doing the GEM pieces. On CPU-bound
graphics tasks, the BKL was showing up as 1-2% of CPU time.
Signed-off-by: Eric Anholt <eric@anholt.net>
Many new laptops now come with 2 gpus, one to be used for low power
modes and one for gaming/on-ac applications. These GPUs are typically
wired to the laptop panel and VGA ports via a multiplexer unit which
is controlled via ACPI methods.
4 combinations of systems typically exist - with 2 ACPI methods.
Intel/ATI - Lenovo W500/T500 - use ATPX ACPI method
ATI/ATI - some ASUS - use ATPX ACPI Method
Intel/Nvidia - - use _DSM ACPI method
Nvidia/Nvidia - - use _DSM ACPI method.
TODO:
This patch adds support for the ATPX method and initial bits
for the _DSM methods that need to written by someone with
access to the hardware.
Add a proper non-debugfs interface - need to get some proper
testing first.
v2: add power up/down support for both devices
on W500 puts i915/radeon into D3 and cuts power to radeon.
v3: redo probing methods, no DMI list, drm devices call to
register with switcheroo, it tries to find an ATPX method on
any device and once there is two devices + ATPX it inits the
switcher.
v4: ATPX msg handling using buffers - should work on more machines
v5: rearchitect after more mjg59 discussion - move ATPX handling to
radeon driver.
v6: add file headers + initial nouveau bits (to be filled out).
v7: merge delayed switcher code.
v8: avoid suspend/resume of gpu that is off
v9: rearchitect - mjg59 is always right. - move all ATPX code to
radeon, should allow simpler DSM also proper ATRM handling
v10: add ATRM support for radeon BIOS, add mutex to lock vgasr_priv
v11: fix bug in resuming Intel for 2nd time.
v12: start fixing up nvidia code blindly.
v13: blindly guess at finishing nvidia code
v14: remove radeon audio hacks - fix up intel resume more like upstream
v15: clean up printks + remove unnecessary igd/dis pointers
mount debugfs
/sys/kernel/debug/vgaswitcheroo/switch - should exist if ATPX detected
+ 2 cards.
DIS - immediate change to discrete
IGD - immediate change to IGD
DDIS - delayed change to discrete
DIGD - delayed change to IGD
ON - turn on not in use
OFF - turn off not in use
Tested on W500 (Intel/ATI) and T500 (Intel/ATI)
Signed-off-by: Dave Airlie <airlied@redhat.com>
New memory control config reg at 0x50 should be used for stolen
memory size detection on Sandybridge.
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
In order to improve our diagnostic capabilities following a GPU hang
and subsequent reset, we need to record the batch buffer that triggered
the error. We assume that the current batch buffer, plus a few details
about what else is on the active list, will be sufficient -- at the very
least an improvement over nothing.
The extra information is stored in /debug/dri/.../i915_error_state
following an error, and may be decoded using
intel_gpu_tools/tools/intel_error_decode.
v2: Avoid excessive work under spinlocks.
v3: Include ringbuffer for later analysis.
v4: Use kunmap correctly and record more buffer state.
v5: Search ringbuffer for current batch buffer
v6: Use a work fn for the impossible IRQ error case.
v7: Avoid non-atomic paths whilst in IRQ context.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Eric Anholt <eric@anholt.net>
Tools like powertop want to check the current FBC status and report it
to the user. So add a debugfs file indicating whether FBC is enabled,
and if not, why.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
As we need more and more controls within MCHBAR for memory config and
power management, this trys to keep MCHBAR enabled from driver load and
only tear down in driver unload.
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
This enables possible 36bit address mask on 965G that use physical
address for hw status page.
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
* 'drm-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
drm/radeon/kms: rs600: use correct mask for SW interrupt
gpu/drm/radeon/radeon_irq.c: move a dereference below a NULL test
drm/radeon/radeon_device.c: move a dereference below a NULL test
drm/radeon/radeon_fence.c: move a dereference below the NULL test
drm/radeon/radeon_connectors.c: add a NULL test before dereference
drm/radeon/kms: fix memory leak
drm/kms: Fix &&/|| confusion in drm_fb_helper_connector_parse_command_line()
drm/edid: Fix CVT width/height decode
drm/edid: Skip empty CVT codepoints
drm: remove address mask param for drm_pci_alloc()
drm/radeon/kms: add missing breaks in i2c and ss lookups
drm/radeon/kms: add primary dac adj values table
drm/radeon/kms: fallback to default connector table
drm_pci_alloc() has input of address mask for setting pci dma
mask on the device, which should be properly setup by drm driver.
And leave it as a param for drm_pci_alloc() would cause confusion
or mistake would corrupt the correct dma mask setting, as seen on
intel hw which set wrong dma mask for hw status page. So remove
it from drm_pci_alloc() function.
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
drivers/gpu/drm/i915/i915_dma.c: In function 'i915_driver_load':
drivers/gpu/drm/i915/i915_dma.c:1114: warning: 'll_base' may be used uninitialized in this function
Partly this is because gcc isn't smart enough. But `ll_base' does get used
uninitialised in the DRM_DEBUG() call.
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: Eric Anholt <eric@anholt.net>
Cc: Dave Airlie <airlied@linux.ie>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
This patch adds a new execbuf ioctl, execbuf2, for use by clients that
want to control fence register allocation more finely. The buffer
passed in to the new ioctl includes a new relocation type to indicate
whether a given object needs a fence register assigned for the command
buffer in question.
Compatibility with the existing execbuf ioctl is implemented in terms
of the new code, preserving the assumption that fence registers are
required for pre-965 rendering commands.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
[ickle: Remove pre-emptive clear_fence_reg()]
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Kristian Høgsberg <krh@bitplanet.net>
[anholt: Removed dmesg spam]
Signed-off-by: Eric Anholt <eric@anholt.net>
This patch changes around our hotplug enable code a bit to only enable
it for ports we actually detect and initialize. This prevents problems
with stuck or spurious interrupts on outputs that aren't actually wired
up, and is generally more correct.
Fixes FDO bug #23183.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
Instead of using the IS_I9XX etc macros that expand to a ton of
comparisons, use new struct intel_device_info to capture the
capabilities of the different chipsets. The drm_i915_private struct
will be initialized to point to the device info that correspond to
the actual device and this way, testing for a specific capability is
just a matter of checking a bit field.
Signed-off-by: Kristian Høgsberg <krh@bitplanet.net>
Signed-off-by: Eric Anholt <eric@anholt.net>
IGD* isn't a useful name. Replace with the codenames, as sourced from
pci.ids.
Signed-off-by: Adam Jackson <ajax@redhat.com>
[anholt: Fixed up for merge with pineview/ironlake changes]
Signed-off-by: Eric Anholt <eric@anholt.net>
Add a GETPARAM request for checking if page flipping is supported.
Useful for the 2D driver to enable the flipping path.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
On some laptops there is no HDMI/DP. But the xrandr still reports
several disconnected HDMI/display ports. In such case the user will be
confused.
>DVI1 disconnected (normal left inverted right x axis y axis)
>DP1 disconnected (normal left inverted right x axis y axis)
>DVI2 disconnected (normal left inverted right x axis y axis)
>DP2 disconnected (normal left inverted right x axis y axis)
>DP3 disconnected (normal left inverted right x axis y axis)
This patch set is to use the child device parsed in VBT to decide whether
the HDMI/DP/LVDS/TV should be initialized.
Parse the child device from VBT.
The device class type is also added for LFP, TV, HDMI, DP output.
https://bugs.freedesktop.org/show_bug.cgi?id=22785
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Reviewed-by: Adam Jackson <ajax@redhat.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Add the support of ACPI opregion on Ironlake so that the backlight
brightness can be adjusted by using ACPI interface
>/sys/class/backlight/acpi_video0/brightness
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Tested-by: Zhao Yakui <yakui.zhao@intel.com>
[zhenyuw: cleanups, fix typo for checking GSE irq and convert to
current irq handling logic.]
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Our work is serialised so allocating per-cpu workqueues is overkill and
a waste of resources.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Eric Anholt <eric@anholt.net>
Replace the DRM_DEBUG with DRM_DEBUG_DRIVER in generic i915 driver.
Then the debug info can be obtained by adding the boot option of
"drm.debug=0x02".
At the same time the debug info in increase/decrease clock is also
printed by using DRM_DEBUG_DRIVER instead of DRM_DEBUG_KMS.
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
This implements intel overlay support for kms via a device-specific
ioctl. Thomas Hellstrom brought up the idea of a general ioctl (on
dri-devel). We've reached the conclusion that such an infrastructure
only makes sense when multiple kms overlay implementations exists,
which atm don't (and it doesn't look like this is gonna change).
Open issues:
- Runs in sync with the gpu, i.e. unnecessary waiting. I've decided
to wait on this because the hw tends to hang when changing something
in this area. I left some dummy functions as infrastructure.
- polyphase filtering uses a static table.
- uses uninterruptible sleeps. Unfortunately the alternatives may
unnecessarily wedged the hw if/when we timeout too early (and
userspace only overloaded the batch buffers with stuff worth a few
secs of gpu time).
Changes since v1:
- fix off-by-one misconception on my side. This fixes fullscreen
playback.
Changes since v2:
- add underrun detection as spec'ed for i965.
- flush caches properly, fixing visual corruptions.
Changes since v4:
- fix up cache flushing of overlay memory regs.
- killed require_pipe_a logic - it hangs the chip.
Tested-By: diego.abelenda@gmail.com (on a 865G)
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
[anholt: Resolved against the MADVISE ioctl going in before this one]
Signed-off-by: Eric Anholt <eric@anholt.net>
Pineview doesn't have this FBC mechanism, so this code doesn't apply.
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
If we trigger a tracepoint for batch buffer submission, it is a reasonable
assumption that we wish to also trace the batch buffer completion. So in
order to capture the completion events, we need to enable irqs... However,
we cannot rely on the completion event to disable the irq later, so we
defer the irq disable to the retire request.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
* 'drm-intel-next' of git://git.kernel.org/pub/scm/linux/kernel/git/anholt/drm-intel: (57 commits)
drm/i915: Handle ERESTARTSYS during page fault
drm/i915: Warn before mmaping a purgeable buffer.
drm/i915: Track purged state.
drm/i915: Remove eviction debug spam
drm/i915: Immediately discard any backing storage for uneeded objects
drm/i915: Do not mis-classify clean objects as purgeable
drm/i915: Whitespace correction for madv
drm/i915: BUG_ON page refleak during unbind
drm/i915: Search harder for a reusable object
drm/i915: Clean up evict from list.
drm/i915: Add tracepoints
drm/i915: framebuffer compression for GM45+
drm/i915: split display functions by chip type
drm/i915: Skip the sanity checks if the current relocation is valid
drm/i915: Check that the relocation points to within the target
drm/i915: correct FBC update when pipe base update occurs
drm/i915: blacklist Acer AspireOne lid status
ACPI: make ACPI button funcs no-ops if not built in
drm/i915: prevent FIFO calculation overflows on 32 bits with high dotclocks
drm/i915: intel_display.c handle latency variable efficiently
...
Fix up trivial conflicts in drivers/gpu/drm/i915/{i915_dma.c|i915_drv.h}
By adding tracepoint equivalents for WATCH_BUF/EXEC we are able to monitor
the lifetimes of objects, requests and significant events. These events can
then be probed using the tracing frameworks, such as systemtap and, in
particular, perf.
For example to record the stack trace for every GPU stall during a run, use
$ perf record -e i915:i915_gem_request_wait_begin -c 1 -g
And
$ perf report
to view the results.
[Updated to fix compilation issues caused.]
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Ben Gamari <bgamari@gmail.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Add support for framebuffer compression on GM45 and above. Removes
some unnecessary I915_HAS_FBC checks as well (this is now part of the
FBC display function).
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
VGA arb requires DRM support for non-kms drivers, to turn on/off
irqs when disabling the mem/io regions.
VGA arb requires KMS support for GPUs where we can turn off VGA
decoding. Currently we know how to do this for intel and radeon
kms drivers, which allows them to be removed from the arbiter.
This patch comes from Fedora rawhide kernel.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Similar to the madvise() concept, the application may wish to mark some
data as volatile. That is in the event of memory pressure the kernel is
free to discard such buffers safe in the knowledge that the application
can recreate them on demand, and is simply using these as a cache.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
This patch puts in place the machinery to attempt to reset the GPU. This
will be used when attempting to recover from a GPU hang.
Signed-off-by: Owain G. Ainsworth <oga@openbsd.org>
Signed-off-by: Ben Gamari <bgamari.foss@gmail.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
We set a periodic timer to check on the GPU, resetting it every time a
batch is completed. If the timer elapses, we check acthd. If acthd
hasn't changed in two timer periods, we assume the chip is wedged.
This is implemented in such a way that it leaves the option open to
employ adaptive timer intervals in the future. One could wait until
several timer periods have elapsed before declaring the chip dead. If
the chip comes back after several periods but before the "dead"
threshold, the timer interval or dead threshold could be raised.
It is important to note that while checking for active requests, we need
to account for the fact that requests are removed from the list (i.e.
retired) in a deferred work queue handler. This means that merely
checking for an empty request_list is insufficient; the list could be
non-empty yet the GPU still idle, causing the hangcheck timer to
incorrectly mark the GPU as wedged (it took me a while to figure that
out---sigh...)
Signed-off-by: Ben Gamari <bgamari.foss@gmail.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
This patch adds framebuffer compression (good for about ~0.5W power
savings in the best case) support for pre-GM45 chips. GM45+ have a new,
more flexible FBC scheme that will be added in a separate patch.
FBC can't always be enabled: the compressed buffer must be physically
contiguous and reside in stolen space. So if you have a large display
and a small amount of stolen memory, you may not be able to take
advantage of FBC. In some cases, a BIOS setting controls how much
stolen space is available. Increasing this to 8 or 16M can help.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
The driver gets the bridge device in a number of places, upcoming
vga arb code paths need the bridge device, however they need it in
under a lock, and the pci lookup can allocate memory. So clean
this code up before then and get the bridge once for the driver lifetime.
Signed-off-by: Dave Airlie <airlied@redhat.com>
According to the docs, the ringbuffer is not allowed to wrap in the middle
of an instruction.
G45 PRM, Vol 1b, p101:
While the “free space” wrap may allow commands to be wrapped around the
end of the Ring Buffer, the wrap should only occur between commands.
Padding (with NOP) may be required to follow this restriction.
Do as commanded.
[Having seen bug reports where there is evidence of split commands, but
apparently the GPU has continued on merrily before a bizarre and untimely
death, this may or may not fix a few random hangs.]
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
CC: Eric Anholt <eric@anholt.net>
Signed-off-by: Eric Anholt <eric@anholt.net>
Initially I always meant this code to be shared, but things
ran away from me before I got to it.
This refactors the i915 and radeon kms fbdev interaction layers
out into generic helpers + driver specific pieces.
It moves all the panic/sysrq enhancements to the core file,
and stores a linked list of kernel fbs. This could possibly be
improved to only store the fb which has fbcon on it for panics
etc.
radeon retains some specific codes used for a big endian
workaround.
changes:
fix oops in v1
fix freeing path for crtc_info
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
We will have to add a prefix when using the macro defintion of DRM_DEBUG_KMS
/DRM_DEBUG_DRIVER/MODE. It is not convenient. We should use the DRM_NAME
as default prefix.
So remove the prefix in the macro definition of DRM_DEBUG_KMS/DRIVER/MODE.
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Acked-by: Ian Romanick <ian.d.romanick@intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This is seen on some G41 systems, where the BIOS will consume all but
a few KB of the aperture. This should be bad for all operating systems, as
it means that the OS can't dynamically manage memory between graphics and
the rest of the system, and OSes that did static memory management
statically add memory in addition to the BIOS allocation anyway. So, instead
of working around it, just fail out verbosely.
fd.o bug #21574
Signed-off-by: Eric Anholt <eric@anholt.net>
Reviewed-by: Ian Romanick <ian.d.romanick@intel.com>
Convert many printk calls to DRM_DEBUG calls to reduce kernel log noise
for normal activities. Switch other printk calls to DRM_ERROR or DRM_INFO.
Signed-off-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
This patch from jbarnes and myself adds FIFO watermark control to the
driver. This is needed for both power saving features on new platforms
with the so-called "big FIFO" and for controlling FIFO allocation
between pipes in multi-head configurations.
It's also necessary infrastructure to support things like framebuffer
compression and configuration supportability checks (i.e. checking a
configuration against available bandwidth).
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
This patch enables error detection by enabling several types of error
interrupts. When an error interrupt is received, the interrupt
handler captures the error state; hopefully resulting in an accurate
set of error data (error type, active head pointer, etc.). The new
record is then available from sysfs. The current code will also dump
the error state to the system log.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
In theory now that the AGP subsystem is using struct page, we should
have on problems enabling GEM on PAE systems.
Signed-off-by: Dave Airlie <airlied@redhat.com>
It hasn't been used in ages, and having the user tell your how much
memory is being freed at free time is a recipe for disaster even if it
was ever used.
Signed-off-by: Eric Anholt <eric@anholt.net>
* 'drm-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6: (50 commits)
drm: include kernel list header file in hashtab header
drm: Export hash table functionality.
drm: Split out the mm declarations in a separate header. Add atomic operations.
drm/radeon: add support for RV790.
drm/radeon: add rv740 drm support.
drm_calloc_large: check right size, check integer overflow, use GFP_ZERO
drm: Eliminate magic I2C frobbing when reading EDID
drm/i915: duplicate desired mode for use by fbcon.
drm/via: vfree() no need checking before calling it
drm: Replace DRM_DEBUG with DRM_DEBUG_DRIVER in i915 driver
drm: Replace DRM_DEBUG with DRM_DEBUG_MODE in drm_mode
drm/i915: Replace DRM_DEBUG with DRM_DEBUG_KMS in intel_sdvo
drm/i915: replace DRM_DEBUG with DRM_DEBUG_KMS in intel_lvds
drm: add separate drm debugging levels
radeon: remove _DRM_DRIVER from the preadded sarea map
drm: don't associate _DRM_DRIVER maps with a master
drm: simplify kcalloc() call to kzalloc().
intelfb: fix spelling of "CLOCK"
drm: fix LOCK_TEST_WITH_RETURN macro
drm/i915: Hook connector to encoder during load detection (fixes tv/vga detect)
...
Replace the DRM_DEBUG with the DRM_DEBUG_DRIVER to print the debug info
in i915 driver.
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Update interrupt handling methods for IGDNG with new registers
for display and graphics interrupt functions. As we won't use
irq-based vblank sync in dri2, so display interrupt on new chip
will be used for hotplug only in future.
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
All G4x and newer chips use the new style frame count register, with a
full 32 bit frame count. Update the code to reflect this.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
This adds kernel mode setting on IGDNG with VGA output support.
Note that suspend/resume doesn't work yet.
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Disable OpRegion support for now until verified on new chipsets.
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
keithp didn't like the original 20ms plan because a cooperative client could
be starved by an uncooperative client. There may even have been problems
with cooperative clients versus cooperative clients. So keithp changed
throttle to just wait for the second to last seqno emitted by that client.
It worked well, until we started getting more round-trips to the server
due to DRI2 -- the server throttles in BlockHandler, and so if you did more
than one round trip after finishing your frame, you'd end up unintentionally
syncing to the swap.
Fix this by keeping track of the client's requests, so the client can wait
when it has an outstanding request over 20ms old. This should have
non-starving behavior, good behavior in the presence of restarts, and less
waiting. Improves high-settings openarena performance on my GM45 by 50%.
Signed-off-by: Eric Anholt <eric@anholt.net>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
allocating devname in the i915 driver was a hack originally and I
forgot to figure out how to do this properly back then.
So this is the cleaner version that just picks devname or driver name
in the irq code.
It removes the devname allocs from the i915 driver.
Signed-off-by: Dave Airlie <airlied@redhat.com>
This allows userlevel code to discover the pipe number corresponding
to a given CRTC ID. This is necessary for doing pipe-specific
operations such as waiting for vblank on a given CRTC. Failure to use
the right pipe mapping can result in GPU hangs, or at least failure
to actually sync to vblank.
Signed-off-by: Carl Worth <cworth@cworth.org>
[anholt: Style touchups from review]
Signed-off-by: Eric Anholt <eric@anholt.net>
This should avoid a class of bugs where the hardware prefetches past the
end of the object, and walks into unallocated memory when the object is
bound to the last page of the aperture.
fd.o bug #21488
Signed-off-by: Eric Anholt <eric@anholt.net>
Commit 201361a5 introduces a leak when unwinding on error. Reorder
unwind, and eliminate leak.
Cc: Eric Anholt <eric@anholt.net>
Cc: Keith Packard <keithp@keithp.com>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
[anholt: fixed uninit variable use introduced in original patch]
Signed-off-by: Eric Anholt <eric@anholt.net>
The i915 DRM triggers registration of the ACPI video driver on load. It
should unregister it at unload in order to avoid generating backtraces on
being reloaded.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Add VGA port hotplug detection to the i915 driver. When KMS is enabled,
plugging in or removing a VGA cable from the VGA connector will
generate a uevent, which indicates to userspace that it should re-probe
outputs on this device (to determine modes, etc.).
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
[anholt: dropped extra PORT_HOTPLUG_STAT clear with ack from jbarnes]
Signed-off-by: Eric Anholt <eric@anholt.net>
IGD device only has last 1 page used by GTT. This should match the AGP gart
code.
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Intel graphics hardware that implements the ACPI IGD OpRegion spec
requires that the list of display devices be populated before any ACPI
video methods are called. Detect when this is the case and defer
registration until the opregion code calls it. Fixes crashes on HP
laptops.
http://bugzilla.kernel.org/show_bug.cgi?id=11259
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Acked-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Len Brown <len.brown@intel.com>
I've hit the occasional oops inside i915_wait_ring() with an indication of
a NULL derefence of dev->primary->master. Adding a NULL check is
consistent with the other potential users of dev->primary->master.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Eric Anholt <eric@anholt.net>
This introduces allocation in the batch submission path that wasn't there
previously, but these are compatibility paths so we care about simplicity
more than performance.
kernel.org bug #12419.
Signed-off-by: Eric Anholt <eric@anholt.net>
Reviewed-by: Keith Packard <keithp@keithp.com>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
The DRM uses its own wrappers to obtain resources from PCI devices,
which currently convert the resource_size_t into an unsigned long.
This is broken on 32-bit platforms with >32-bit physical address
space.
This fixes them, along with a few occurences of unsigned long used
to store such a resource in drivers.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Dave Airlie <airlied@linux.ie>
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86: enable DMAR by default
xen: disable interrupts early, as start_kernel expects
gpu/drm, x86, PAT: io_mapping_create_wc and resource_size_t
gpu/drm, x86, PAT: Handle io_mapping_create_wc() errors in a clean way
x86, Voyager: fix compile by lifting the degeneracy of phys_cpu_present_map
x86, doc: fix references to Documentation/x86/i386/boot.txt
io_mapping_create_wc can return NULL on error and io_mapping_free() should be
called on one of the error-cleanup path.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: Dave Airlie <airlied@redhat.com>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: Eric Anholt <eric@anholt.net>
Cc: Keith Packard <keithp@keithp.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
However we still have another issue with ioremap_wc not falling back
properly or somehow doing something else stupid, this probably needs
to be tracked down.
Signed-off-by: Dave Airlie <airlied@redhat.com>
