Always clear out these floppy_raw_cmd struct members after copying the
entire structure from userspace so that the in-kernel version is always
valid and never left in an interdeterminate state.
Signed-off-by: Matthew Daley <mattd@bugfuzz.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Since commit 1df5a06a ("ALSA: hda - hdmi: Fix programmed active channel
count") channel count is no longer being set if monitor_present is 0.
This is because setting the count was moved after the CA value is
determined, which is only after the monitor_present check in
hdmi_setup_audio_infoframe().
Unfortunately, in some cases, such as with a non-spec-compliant codec or
with a problematic video driver, monitor_present is always 0. As a
specific example, this seems to happen with gen1 ATV (SiI1390 codec),
causing left-channel-only stereo playback (multi-channel playback has
apparently never worked with this codec despite it reporting 8 channels,
reason unknown).
Simply setting converter channel count without setting the pin infoframe
and channel mapping as well does not theoretically make much sense as
this will just mean they are out-of-sync and multichannel playback will
have a wrong channel mapping.
However, adding back just setting the converter channel count even in
no-monitor case is the safest change which at least fixes the stereo
playback regression on SiI1390 codec. Do that.
Signed-off-by: Anssi Hannula <anssi.hannula@iki.fi>
Reported-by: Stephan Raue <stephan@openelec.tv>
Tested-by: Stephan Raue <stephan@openelec.tv>
Cc: <stable@vger.kernel.org> # 3.12+
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This touchpad seriously dislikes init reports, not only timeing out, but
also refusing to work after this.
Cc: stable@vger.kernel.org
Reported-and-tested-by: Vincent Fortier <th0ma7@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The extra seven bits are only required when allocating the report buffer.
We can not use those extra bytes for the length of the report in the
generic implementation of .request because the device might (will) refuse
the set_report command.
This has been verified on the Atmel touchpad found on the Samsung Ativ 9
plus, which uses hid-multitouch and HID over I2C. Without this fix, the
device refuses to switch to the multitouch mode, and it becomes unresponsive
from the user point of view.
Actually, this has been discussed during the initial submission of the
commit 4fa5a7f76c, see
https://patchwork.kernel.org/patch/3621751/
Unfortunately, I completely forgot about it later.
Reported-by: Matthias Bayer <thematthiasbayer@gmail.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
When building the name for the workqueue thread, make sure a format
string cannot leak in from the disk name.
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
The ubi->free_count should be updated with every insert/remove to/from
the ubi->free list.
Signed-off-by: Tanya Brokhman <tlinder@codeaurora.org>
Reviewed-by: Dolev Raviv <draviv@codeaurora.org>
Acked-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
In case of an error (if there are not free PEB's for example),
__wl_get_peb will return a negative value. In order to prevent access
violation we need to test the returned value prior to using it later on.
Signed-off-by: Tatyana Brokhman <tlinder@codeaurora.org>
Reviewed-by: Dolev Raviv <draviv@codeaurora.org>
Acked-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Dan's "smatch" checker found out that there was a bug in the error path of the
'ubifs_remount_rw()' function. Instead of jumping to the "out" label which
cleans-things up, we just returned.
This patch fixes the problem.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
We have had this code in the kernel for over a year now and have
shaken all the known issues out of the code over the past few
releases. It's now time to remove the experimental warnings during
mount and fully support the new filesystem format in production
systems.
Remove the experimental warning, and add a version number to the
initial "mounting filesystem" message to tell use what type of
filesystem is being mounted. Also, remove the temporary inode
cluster size output at mount time now we know that this code works
fine.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Signed-off-by: Dave Chinner <david@fromorbit.com>
On 64 bit systems the agp_info struct has a 4 byte hole between
->agp_mode and ->aper_base. We need to clear it to avoid disclosing
stack information to userspace.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
hhf_change() takes the sch_tree_lock and releases it but misses the
error cases. Fix the missed case here.
To reproduce try a command like this,
# tc qdisc change dev p3p2 root hhf quantum 40960 non_hh_weight 300000
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- only an email address change to the MAINTAINERS file
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=JLHy
-----END PGP SIGNATURE-----
Merge tag 'locks-v3.15-3' of git://git.samba.org/jlayton/linux
Pull file locking change from Jeff Layton:
"Only an email address change to the MAINTAINERS file"
* tag 'locks-v3.15-3' of git://git.samba.org/jlayton/linux:
MAINTAINERS: email address change for Jeff Layton
arm64 move of of_clk_init() call in a previous commit
- Default DMA ops changed to non-coherent to preserve compatibility with
32-bit ARM DT files. The "dma-coherent" property can be used to
explicitly mark a device coherent. The Applied Micro DT file has been
updated to avoid DMA cache maintenance for the X-Gene SATA controller
(the only arm64 related driver with such assumption in -rc mainline)
- Fixmap correction for earlyprintk
- kern_addr_valid() fix for huge pages
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.9 (GNU/Linux)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=kRLA
-----END PGP SIGNATURE-----
Merge tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 fixes from Catalin Marinas:
"These are mostly arm64 fixes with an additional arm(64) platform fix
for the initialisation of vexpress clocks (the latter only affecting
arm64; the arch/arm64 code is SoC agnostic and does not rely on early
SoC-specific calls)
- vexpress platform clocks initialisation moved earlier following the
arm64 move of of_clk_init() call in a previous commit
- Default DMA ops changed to non-coherent to preserve compatibility
with 32-bit ARM DT files. The "dma-coherent" property can be used
to explicitly mark a device coherent. The Applied Micro DT file
has been updated to avoid DMA cache maintenance for the X-Gene SATA
controller (the only arm64 related driver with such assumption in
-rc mainline)
- Fixmap correction for earlyprintk
- kern_addr_valid() fix for huge pages"
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
vexpress: Initialise the sysregs before setting up the clocks
arm64: Mark the Applied Micro X-Gene SATA controller as DMA coherent
arm64: Use bus notifiers to set per-device coherent DMA ops
arm64: Make default dma_ops to be noncoherent
arm64: fixmap: fix missing sub-page offset for earlyprintk
arm64: Fix for the arm64 kern_addr_valid() function
This is two patches both fixing bugs in drivers (virtio-scsi and mpt2sas)
causing an oops in certain circumstances.
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iQEcBAABAgAGBQJTZdBVAAoJEDeqqVYsXL0MIYMIAI/rDIV/MeF0OZd3nzTaEAIG
i8HPPgBTmSKmK3q04Pjjtc1CHW3unH6cr1tG1L4r1tyoxwcnZ0+x87fi3KcLIpBb
G6o/31QpniNQ/3LNdwCHtyl760XVZhWz6XpJ/NCmWuYeKx1RmT3W+ggnXD+fznNs
3h347rIrr4efkgRJIzzfi6pYa55VmvI6M7J/RpXmMg/IcfF+GBJfyEp0AsmIoYno
YVwFBB8h9cVsgvhROn8i1pYq1YOf9jo298LLMULMIvu9iZWHp57GOzA4HzyEa9kp
T1I6AzwJGbmirJsm0yD1hKgJns3Za+ZA3FeP5qQ7BX38YI7EKkkd+qtCMzT1YfY=
=whLk
-----END PGP SIGNATURE-----
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"This is two patches both fixing bugs in drivers (virtio-scsi and
mpt2sas) causing an oops in certain circumstances"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
[SCSI] virtio-scsi: Skip setting affinity on uninitialized vq
[SCSI] mpt2sas: Don't disable device twice at suspend.
of the framebuffer when early_ioremap() is no longer available and
dropping __init from functions that may be invoked after
free_initmem() - Dave Young
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=BzhM
-----END PGP SIGNATURE-----
Merge tag 'efi-urgent' of git://git.kernel.org/pub/scm/linux/kernel/git/mfleming/efi into x86/urgent
Pull EFI fix from Matt Fleming:
" * Fix earlyprintk=efi,keep support by switching to an ioremap() mapping
of the framebuffer when early_ioremap() is no longer available and
dropping __init from functions that may be invoked after
free_initmem() - Dave Young "
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Following arm64 commit bc3ee18a7a (arm64: init: Move of_clk_init to
time_init()), vexpress_osc_of_setup() is called via of_clk_init() long
before initcalls are issued. Initialising the vexpress oscillators
requires the vespress sysregs to be already initialised, so this patch
adds an explicit call to vexpress_sysreg_of_early_init() in vexpress
oscillator setup function.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Tested-by: Will Deacon <will.deacon@arm.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Tested-by: Pawel Moll <pawel.moll@arm.com>
Acked-by: Pawel Moll <pawel.moll@arm.com>
Cc: Mike Turquette <mturquette@linaro.org>
pte_ERROR() is not used anywhere, delete it.
For pgd_ERROR() and pmd_ERROR(), output something similar to x86, giving the address
of the pgd/pmd as well as it's value.
Also provide the caller, since these macros are invoked from pgd_clear_bad() and
pmd_clear_bad() which provides little context as to what high level operation was
occuring when the BAD state was detected.
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of returning false we should at least check the most basic
things, otherwise page table corruptions will be very difficult to
debug.
PMD and PTE tables are of size PAGE_SIZE, so none of the sub-PAGE_SIZE
bits should be set.
We also complement this with a check that the physical address the
pud/pmd points to is valid memory.
PowerPC was used as a guide while implementating this.
Signed-off-by: David S. Miller <davem@davemloft.net>
In commit b2d4383480 ("sparc64: Make
PAGE_OFFSET variable."), the MAX_PHYS_ADDRESS_BITS value was increased
(to 47).
This constant reference to '41UL' was missed.
Signed-off-by: David S. Miller <davem@davemloft.net>
Make get_user_insn() able to cope with huge PMDs.
Next, make do_fault_siginfo() more robust when get_user_insn() can't
actually fetch the instruction. In particular, use the MMU announced
fault address when that happens, instead of calling
compute_effective_address() and computing garbage.
Signed-off-by: David S. Miller <davem@davemloft.net>
If we have a 32-bit task we must chop off the top 32-bits of the
64-bit value just as the cpu would.
Signed-off-by: David S. Miller <davem@davemloft.net>
The large PMD path needs to check _PAGE_VALID not _PAGE_PRESENT, to
decide if it needs to bail and return 0.
pmd_large() should therefore just check _PAGE_PMD_HUGE.
Calls to gup_huge_pmd() are guarded with a check of pmd_large(), so we
just need to add a valid bit check.
Signed-off-by: David S. Miller <davem@davemloft.net>
On sparc64 "present" and "valid" are seperate PTE bits, this allows us to
naturally distinguish between the user explicitly asking for PROT_NONE
with mprotect() and other situations.
However we weren't handling this properly in the huge PMD paths.
First of all, the page table walker in the TSB miss path only checks
for _PAGE_PMD_HUGE. So the generic pmdp_invalidate() would clear
_PAGE_PRESENT but the TLB miss paths would still load it into the TLB
as a valid huge PMD.
Fix this by clearing the valid bit in pmdp_invalidate(), and also
checking the valid bit in USER_PGTABLE_CHECK_PMD_HUGE using "brgez"
since _PAGE_VALID is bit 63 in both the sun4u and sun4v pte layouts.
Signed-off-by: David S. Miller <davem@davemloft.net>
This code was mistakenly using the exec bit from the PMD in all
cases, even when the PMD isn't a huge PMD.
If it's not a huge PMD, test the exec bit in the individual ptes down
in tlb_batch_pmd_scan().
Signed-off-by: David S. Miller <davem@davemloft.net>
Bring this code in line with the perf based generic NMI watchdog
in kernel/watchdog.c (which we should convert over to at some
point).
In particular, don't do anything super fancy when the watchdog
triggers, and specifically don't do a do_exit() which only makes
things worse.
Either panic(), or WARN(). The latter of which will do all of
the actions such as give us a stack backtrace.
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 6a20dbd6ca,
"tty: Fix race condition between __tty_buffer_request_room and flush_to_ldisc"
correctly identifies an unsafe race condition between
__tty_buffer_request_room() and flush_to_ldisc(), where the consumer
flush_to_ldisc() prematurely advances the head before consuming the
last of the data committed. For example:
CPU 0 | CPU 1
__tty_buffer_request_room | flush_to_ldisc
... | ...
| count = head->commit - head->read
n = tty_buffer_alloc() |
b->commit = b->used |
b->next = n |
| if (!count) /* T */
| if (head->next == NULL) /* F */
| buf->head = head->next
In this case, buf->head has been advanced but head->commit may have
been updated with a new value.
Instead of reintroducing an unnecessary lock, fix the race locklessly.
Read the commit-next pair in the reverse order of writing, which guarantees
the commit value read is the latest value written if the head is
advancing.
Reported-by: Manfred Schlaegl <manfred.schlaegl@gmx.at>
Cc: <stable@vger.kernel.org> # 3.12.x+
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 6a20dbd6ca.
Although the commit correctly identifies an unsafe race condition
between __tty_buffer_request_room() and flush_to_ldisc(), the commit
fixes the race with an unnecessary spinlock in a lockless algorithm.
The follow-on commit, "tty: Fix lockless tty buffer race" fixes
the race locklessly.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When 'console=hvc0' is specified to the kernel parameter in x86 KVM guest,
hvc console is setup within a kthread. However, that will cause SEGV
and the boot will fail when the driver is builtin to the kernel,
because currently hvc_console_setup() is annotated with '__init'. This
patch removes '__init' to boot the guest successfully with 'console=hvc0'.
Signed-off-by: Tomoki Sekiyama <tomoki.sekiyama@hds.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The tty atomic_write_lock does not provide an exclusion guarantee for
the tty driver if the termios settings are LECHO & !OPOST. And since
it is unexpected and not allowed to call TTY buffer helpers like
tty_insert_flip_string concurrently, this may lead to crashes when
concurrect writers call pty_write. In that case the following two
writers:
* the ECHOing from a workqueue and
* pty_write from the process
race and can overflow the corresponding TTY buffer like follows.
If we look into tty_insert_flip_string_fixed_flag, there is:
int space = __tty_buffer_request_room(port, goal, flags);
struct tty_buffer *tb = port->buf.tail;
...
memcpy(char_buf_ptr(tb, tb->used), chars, space);
...
tb->used += space;
so the race of the two can result in something like this:
A B
__tty_buffer_request_room
__tty_buffer_request_room
memcpy(buf(tb->used), ...)
tb->used += space;
memcpy(buf(tb->used), ...) ->BOOM
B's memcpy is past the tty_buffer due to the previous A's tb->used
increment.
Since the N_TTY line discipline input processing can output
concurrently with a tty write, obtain the N_TTY ldisc output_lock to
serialize echo output with normal tty writes. This ensures the tty
buffer helper tty_insert_flip_string is not called concurrently and
everything is fine.
Note that this is nicely reproducible by an ordinary user using
forkpty and some setup around that (raw termios + ECHO). And it is
present in kernels at least after commit
d945cb9cce (pty: Rework the pty layer to
use the normal buffering logic) in 2.6.31-rc3.
js: add more info to the commit log
js: switch to bool
js: lock unconditionally
js: lock only the tty->ops->write call
References: CVE-2014-0196
Reported-and-tested-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The sleep function was updated to put the serial port to sleep only when necessary.
This appears to resolve the errant behavior of the driver as described in
Kernel Bug 61961 – "My Exar Corp. XR17C/D152 Dual PCI UART modem does not
work with 3.8.0".
Signed-off-by: Michael Welling <mwelling@ieee.org>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Per reference manuals of Freescale P1020 and P2020 SoCs, USB controller
present in these SoCs has bit 17 of USBx_CONTROL register marked as
Reserved - there is no PHY_CLK_VALID bit there.
Testing for this bit in ehci_fsl_setup_phy() behaves differently on two
P1020RDB boards available here - on one board test passes and fsl-usb
init succeeds, but on other board test fails, causing fsl-usb init to
fail.
This patch changes ehci_fsl_setup_phy() not to test PHY_CLK_VALID on
controller version 1.6 that (per manual) does not have this bit.
Signed-off-by: Nikita Yushchenko <nyushchenko@dev.rtsoft.ru>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Even if the USB-to-ATAPI converter supported multiple LUNs, this
driver would always detect the same physical device or media because
it doesn't use srb->device->lun in any way.
Tested with an Hewlett-Packard CD-Writer Plus 8200e.
Signed-off-by: Daniele Forsi <dforsi@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Dan writes:
"The Dell drivers use the same configuration for PIDs:
81A2: Dell Wireless 5806 Gobi(TM) 4G LTE Mobile Broadband Card
81A3: Dell Wireless 5570 HSPA+ (42Mbps) Mobile Broadband Card
81A4: Dell Wireless 5570e HSPA+ (42Mbps) Mobile Broadband Card
81A8: Dell Wireless 5808 Gobi(TM) 4G LTE Mobile Broadband Card
81A9: Dell Wireless 5808e Gobi(TM) 4G LTE Mobile Broadband Card
These devices are all clearly Sierra devices, but are also definitely
Gobi-based. The A8 might be the MC7700/7710 and A9 is likely a MC7750.
>From DellGobi5kSetup.exe from the Dell drivers:
usbif0: serial/firmware loader?
usbif2: nmea
usbif3: modem/ppp
usbif8: net/QMI"
Cc: <stable@vger.kernel.org>
Reported-by: AceLan Kao <acelan.kao@canonical.com>
Reported-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some OHCI controllers from ATI/AMD seem to have difficulty with
"global" USB suspend, that is, suspending an entire USB bus without
setting the suspend feature for each port connected to a device. When
we try to resume the child devices, the controller gives timeout
errors on the unsuspended ports, requiring resets, and can even cause
ohci-hcd to hang; see
http://marc.info/?l=linux-usb&m=139514332820398&w=2
and the following messages.
This patch fixes the problem by adding a new quirk flag to ohci-hcd.
The flag causes the ohci_rh_suspend() routine to suspend each
unsuspended, enabled port before suspending the root hub. This
effectively converts the "global" suspend to an ordinary root-hub
suspend. There is no need to unsuspend these ports when the root hub
is resumed, because the child devices will be resumed anyway in the
course of a normal system resume ("global" suspend is never used for
runtime PM).
This patch should be applied to all stable kernels which include
commit 0aa2832dd0 (USB: use "global suspend" for system sleep on
USB-2 buses) or a backported version thereof.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Peter Münster <pmlists@free.fr>
Tested-by: Peter Münster <pmlists@free.fr>
CC: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since the default DMA ops for arm64 are non-coherent, mark the X-Gene
controller explicitly as dma-coherent to avoid additional cache
maintenance.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Cc: Loc Ho <lho@apm.com>
Recently, the default DMA ops have been changed to non-coherent for
alignment with 32-bit ARM platforms (and DT files). This patch adds bus
notifiers to be able to set the coherent DMA ops (with no cache
maintenance) for devices explicitly marked as coherent via the
"dma-coherent" DT property.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Currently arm64 dma_ops is by default made coherent which makes it
opposite in default policy from arm.
Make default dma_ops to be noncoherent (same as arm), as currently there
aren't any dma-capable drivers which assumes coherent ops
Signed-off-by: Ritesh Harjani <ritesh.harjani@gmail.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Commit d57c33c5da (add generic fixmap.h) added (among other
similar things) set_fixmap_io to deal with early ioremap of devices.
More recently, commit bf4b558eba (arm64: add early_ioremap support)
converted the arm64 earlyprintk to use set_fixmap_io. A side effect of
this conversion is that my virtual machines have stopped booting when
I pass "earlyprintk=uart8250-8bit,0x3f8" to the guest kernel.
Turns out that the new earlyprintk code doesn't care at all about
sub-page offsets, and just assumes that the earlyprintk device will
be page-aligned. Obviously, that doesn't play well with the above example.
Further investigation shows that set_fixmap_io uses __set_fixmap instead
of __set_fixmap_offset. A fix is to introduce a set_fixmap_offset_io that
uses the latter, and to remove the superflous call to fix_to_virt
(which only returns the value that set_fixmap_io has already given us).
With this applied, my VMs are back in business. Tested on a Cortex-A57
platform with kvmtool as platform emulation.
Cc: Will Deacon <will.deacon@arm.com>
Acked-by: Mark Salter <msalter@redhat.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Fix for the arm64 kern_addr_valid() function to recognize
virtual addresses in the kernel logical memory map. The
function fails as written because it does not check whether
the addresses in that region are mapped at the pmd level to
2MB or 512MB pages, continues the page table walk to the
pte level, and issues a garbage value to pfn_valid().
Tested on 4K-page and 64K-page kernels.
Signed-off-by: Dave Anderson <anderson@redhat.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Since now the shrink list is private and nobody can free the dentry while
it is on the shrink list, we can remove RCU protection from this.
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Start with shrink_dcache_parent(), then scan what remains.
First of all, BUG() is very much an overkill here; we are holding
->s_umount, and hitting BUG() means that a lot of interesting stuff
will be hanging after that point (sync(2), for example). Moreover,
in cases when there had been more than one leak, we'll be better
off reporting all of them. And more than just the last component
of pathname - %pd is there for just such uses...
That was the last user of dentry_lru_del(), so kill it off...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
If we find something already on a shrink list, just increment
data->found and do nothing else. Loops in shrink_dcache_parent() and
check_submounts_and_drop() will do the right thing - everything we
did put into our list will be evicted and if there had been nothing,
but data->found got non-zero, well, we have somebody else shrinking
those guys; just try again.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Pull irq fixes from Thomas Gleixner:
"This udpate delivers:
- A fix for dynamic interrupt allocation on x86 which is required to
exclude the GSI interrupts from the dynamic allocatable range.
This was detected with the newfangled tablet SoCs which have GPIOs
and therefor allocate a range of interrupts. The MSI allocations
already excluded the GSI range, so we never noticed before.
- The last missing set_irq_affinity() repair, which was delayed due
to testing issues
- A few bug fixes for the armada SoC interrupt controller
- A memory allocation fix for the TI crossbar interrupt controller
- A trivial kernel-doc warning fix"
* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
irqchip: irq-crossbar: Not allocating enough memory
irqchip: armanda: Sanitize set_irq_affinity()
genirq: x86: Ensure that dynamic irq allocation does not conflict
linux/interrupt.h: fix new kernel-doc warnings
irqchip: armada-370-xp: Fix releasing of MSIs
irqchip: armada-370-xp: implement the ->check_device() msi_chip operation
irqchip: armada-370-xp: fix invalid cast of signed value into unsigned variable
Pull timer fixes from Thomas Gleixner:
"This update brings along:
- Two fixes for long standing bugs in the hrtimer code, one which
prevents remote enqueuing and the other preventing arbitrary delays
after a interrupt hang was detected
- A fix in the timer wheel which prevents math overflow
- A fix for a long standing issue with the architected ARM timer
related to the C3STOP mechanism.
- A trivial compile fix for nspire SoC clocksource"
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
timer: Prevent overflow in apply_slack
hrtimer: Prevent remote enqueue of leftmost timers
hrtimer: Prevent all reprogramming if hang detected
clocksource: nspire: Fix compiler warning
clocksource: arch_arm_timer: Fix age-old arch timer C3STOP detection issue
