Steffen Klassert says:
====================
1) Fix PMTU for IPv6 if the reported MTU minus the ESP overhead is
smaller than 1280. From Jiri Bohac.
2) Fix xfrm interface ID and inter address family tunneling when
migrating xfrm states. From Yan Yan.
3) Add missing xfrm intrerface ID initialization on xfrmi_changelink.
From Antony Antony.
4) Enforce validity of xfrm offload input flags so that userspace can't
send undefined flags to the offload driver.
From Leon Romanovsky.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
If I'm not mistaken (and I don't think I am), the way in which the
dcbnl_ops work is that drivers call dcb_ieee_setapp() and this populates
the application table with dynamically allocated struct dcb_app_type
entries that are kept in the module-global dcb_app_list.
However, nobody keeps exact track of these entries, and although
dcb_ieee_delapp() is supposed to remove them, nobody does so when the
interface goes away (example: driver unbinds from device). So the
dcb_app_list will contain lingering entries with an ifindex that no
longer matches any device in dcb_app_lookup().
Reclaim the lost memory by listening for the NETDEV_UNREGISTER event and
flushing the app table entries of interfaces that are now gone.
In fact something like this used to be done as part of the initial
commit (blamed below), but it was done in dcbnl_exit() -> dcb_flushapp(),
essentially at module_exit time. That became dead code after commit
7a6b6f515f ("DCB: fix kconfig option") which essentially merged
"tristate config DCB" and "bool config DCBNL" into a single "bool config
DCB", so net/dcb/dcbnl.c could not be built as a module anymore.
Commit 36b9ad8084 ("net/dcb: make dcbnl.c explicitly non-modular")
recognized this and deleted dcbnl_exit() and dcb_flushapp() altogether,
leaving us with the version we have today.
Since flushing application table entries can and should be done as soon
as the netdevice disappears, fundamentally the commit that is to blame
is the one that introduced the design of this API.
Fixes: 9ab933ab2c ("dcbnl: add appliction tlv handlers")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There's a potential leak issue under following execution sequence :
smc_release smc_connect_work
if (sk->sk_state == SMC_INIT)
send_clc_confirim
tcp_abort();
...
sk.sk_state = SMC_ACTIVE
smc_close_active
switch(sk->sk_state) {
...
case SMC_ACTIVE:
smc_close_final()
// then wait peer closed
Unfortunately, tcp_abort() may discard CLC CONFIRM messages that are
still in the tcp send buffer, in which case our connection token cannot
be delivered to the server side, which means that we cannot get a
passive close message at all. Therefore, it is impossible for the to be
disconnected at all.
This patch tries a very simple way to avoid this issue, once the state
has changed to SMC_ACTIVE after tcp_abort(), we can actively abort the
smc connection, considering that the state is SMC_INIT before
tcp_abort(), abandoning the complete disconnection process should not
cause too much problem.
In fact, this problem may exist as long as the CLC CONFIRM message is
not received by the server. Whether a timer should be added after
smc_close_final() needs to be discussed in the future. But even so, this
patch provides a faster release for connection in above case, it should
also be valuable.
Fixes: 39f41f367b ("net/smc: common release code for non-accepted sockets")
Signed-off-by: D. Wythe <alibuda@linux.alibaba.com>
Acked-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Syzkaller with UBSAN uncovered a scenario where a large number of
DATA_FIN retransmits caused a shift-out-of-bounds in the DATA_FIN
timeout calculation:
================================================================================
UBSAN: shift-out-of-bounds in net/mptcp/protocol.c:470:29
shift exponent 32 is too large for 32-bit type 'unsigned int'
CPU: 1 PID: 13059 Comm: kworker/1:0 Not tainted 5.17.0-rc2-00630-g5fbf21c90c60 #1
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.13.0-1ubuntu1.1 04/01/2014
Workqueue: events mptcp_worker
Call Trace:
<TASK>
__dump_stack lib/dump_stack.c:88 [inline]
dump_stack_lvl+0xcd/0x134 lib/dump_stack.c:106
ubsan_epilogue+0xb/0x5a lib/ubsan.c:151
__ubsan_handle_shift_out_of_bounds.cold+0xb2/0x20e lib/ubsan.c:330
mptcp_set_datafin_timeout net/mptcp/protocol.c:470 [inline]
__mptcp_retrans.cold+0x72/0x77 net/mptcp/protocol.c:2445
mptcp_worker+0x58a/0xa70 net/mptcp/protocol.c:2528
process_one_work+0x9df/0x16d0 kernel/workqueue.c:2307
worker_thread+0x95/0xe10 kernel/workqueue.c:2454
kthread+0x2f4/0x3b0 kernel/kthread.c:377
ret_from_fork+0x1f/0x30 arch/x86/entry/entry_64.S:295
</TASK>
================================================================================
This change limits the maximum timeout by limiting the size of the
shift, which keeps all intermediate values in-bounds.
Closes: https://github.com/multipath-tcp/mptcp_net-next/issues/259
Fixes: 6477dd39e6 ("mptcp: Retransmit DATA_FIN")
Acked-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The MPTCP SIOCOUTQ implementation is not very accurate in
case of fallback: it only measures the data in the MPTCP-level
write queue, but it does not take in account the subflow
write queue utilization. In case of fallback the first can be
empty, while the latter is not.
The above produces sporadic self-tests issues and can foul
legit user-space application.
Fix the issue additionally querying the subflow in case of fallback.
Fixes: 644807e3e4 ("mptcp: add SIOCINQ, OUTQ and OUTQNSD ioctls")
Closes: https://github.com/multipath-tcp/mptcp_net-next/issues/260
Reported-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When using hci_le_create_conn_sync it shall wait for the conn_timeout
since the connection complete may take longer than just 2 seconds.
Also fix the masking of HCI_EV_LE_ENHANCED_CONN_COMPLETE and
HCI_EV_LE_CONN_COMPLETE so they are never both set so we can predict
which one the controller will use in case of HCI_OP_LE_CREATE_CONN.
Fixes: 6cd29ec6ae ("Bluetooth: hci_sync: Wait for proper events when connecting LE")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
hci_update_accept_list_sync is returning the filter based on the error
but that gets overwritten by hci_le_set_addr_resolution_enable_sync
return instead of using the actual result of the likes of
hci_le_add_accept_list_sync which was intended.
Fixes: ad383c2c65 ("Bluetooth: hci_sync: Enable advertising when LL privacy is enabled")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Previous commit e04480920d ("Bluetooth: defer cleanup of resources
in hci_unregister_dev()") defers all destructive actions to
hci_release_dev() to prevent cocurrent problems like NPD, UAF.
However, there are still some exceptions that are ignored.
The smp_unregister() in hci_dev_close_sync() (previously in
hci_dev_do_close) will release resources like the sensitive channel
and the smp_dev objects. Consider the situations the device is detaching
or power down while the kernel is still operating on it, the following
data race could take place.
thread-A hci_dev_close_sync | thread-B read_local_oob_ext_data
|
hci_dev_unlock() |
... | hci_dev_lock()
if (hdev->smp_data) |
chan = hdev->smp_data |
| chan = hdev->smp_data (3)
|
hdev->smp_data = NULL (1) | if (!chan || !chan->data) (4)
... |
smp = chan->data | smp = chan->data
if (smp) |
chan->data = NULL (2) |
... |
kfree_sensitive(smp) |
| // dereference smp trigger UFA
That is, the objects hdev->smp_data and chan->data both suffer from the
data races. In a preempt-enable kernel, the above schedule (when (3) is
before (1) and (4) is before (2)) leads to UAF bugs. It can be
reproduced in the latest kernel and below is part of the report:
[ 49.097146] ================================================================
[ 49.097611] BUG: KASAN: use-after-free in smp_generate_oob+0x2dd/0x570
[ 49.097611] Read of size 8 at addr ffff888006528360 by task generate_oob/155
[ 49.097611]
[ 49.097611] Call Trace:
[ 49.097611] <TASK>
[ 49.097611] dump_stack_lvl+0x34/0x44
[ 49.097611] print_address_description.constprop.0+0x1f/0x150
[ 49.097611] ? smp_generate_oob+0x2dd/0x570
[ 49.097611] ? smp_generate_oob+0x2dd/0x570
[ 49.097611] kasan_report.cold+0x7f/0x11b
[ 49.097611] ? smp_generate_oob+0x2dd/0x570
[ 49.097611] smp_generate_oob+0x2dd/0x570
[ 49.097611] read_local_oob_ext_data+0x689/0xc30
[ 49.097611] ? hci_event_packet+0xc80/0xc80
[ 49.097611] ? sysvec_apic_timer_interrupt+0x9b/0xc0
[ 49.097611] ? asm_sysvec_apic_timer_interrupt+0x12/0x20
[ 49.097611] ? mgmt_init_hdev+0x1c/0x240
[ 49.097611] ? mgmt_init_hdev+0x28/0x240
[ 49.097611] hci_sock_sendmsg+0x1880/0x1e70
[ 49.097611] ? create_monitor_event+0x890/0x890
[ 49.097611] ? create_monitor_event+0x890/0x890
[ 49.097611] sock_sendmsg+0xdf/0x110
[ 49.097611] __sys_sendto+0x19e/0x270
[ 49.097611] ? __ia32_sys_getpeername+0xa0/0xa0
[ 49.097611] ? kernel_fpu_begin_mask+0x1c0/0x1c0
[ 49.097611] __x64_sys_sendto+0xd8/0x1b0
[ 49.097611] ? syscall_exit_to_user_mode+0x1d/0x40
[ 49.097611] do_syscall_64+0x3b/0x90
[ 49.097611] entry_SYSCALL_64_after_hwframe+0x44/0xae
[ 49.097611] RIP: 0033:0x7f5a59f51f64
...
[ 49.097611] RAX: ffffffffffffffda RBX: 0000000000000000 RCX: 00007f5a59f51f64
[ 49.097611] RDX: 0000000000000007 RSI: 00007f5a59d6ac70 RDI: 0000000000000006
[ 49.097611] RBP: 0000000000000000 R08: 0000000000000000 R09: 0000000000000000
[ 49.097611] R10: 0000000000000040 R11: 0000000000000246 R12: 00007ffec26916ee
[ 49.097611] R13: 00007ffec26916ef R14: 00007f5a59d6afc0 R15: 00007f5a59d6b700
To solve these data races, this patch places the smp_unregister()
function in the protected area by the hci_dev_lock(). That is, the
smp_unregister() function can not be concurrently executed when
operating functions (most of them are mgmt operations in mgmt.c) hold
the device lock.
This patch is tested with kernel LOCK DEBUGGING enabled. The price from
the extended holding time of the device lock is supposed to be low as the
smp_unregister() function is fairly short and efficient.
Signed-off-by: Lin Ma <linma@zju.edu.cn>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
sent_cmd memory is not freed before freeing hci_dev causing it to leak
it contents.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
As Jakub noticed, prints should be avoided on the datapath.
Also, as packets would never come to the else branch in
ping_lookup(), remove pr_err() from ping_lookup().
Fixes: 35a79e64de ("ping: fix the dif and sdif check in ping_lookup")
Reported-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Link: https://lore.kernel.org/r/1ef3f2fcd31bd681a193b1fcf235eee1603819bd.1645674068.git.lucien.xin@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
valid_lft, prefered_lft and tstamp are always accessed under the lock
"lock" in other places. Reading these without taking the lock may result
in inconsistencies regarding the calculation of the valid and preferred
variables since decisions are taken on these fields for those variables.
Signed-off-by: Niels Dossche <dossche.niels@gmail.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: Niels Dossche <niels.dossche@ugent.be>
Link: https://lore.kernel.org/r/20220223131954.6570-1-niels.dossche@ugent.be
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
smc_pnetid_by_table_ib() uses read_lock() and then it calls smc_pnet_apply_ib()
which, in turn, calls mutex_lock(&smc_ib_devices.mutex).
read_lock() disables preemption. Therefore, the code acquires a mutex while in
atomic context and it leads to a SAC bug.
Fix this bug by replacing the rwlock with a mutex.
Reported-and-tested-by: syzbot+4f322a6d84e991c38775@syzkaller.appspotmail.com
Fixes: 64e28b52c7 ("net/smc: add pnet table namespace support")
Confirmed-by: Tony Lu <tonylu@linux.alibaba.com>
Signed-off-by: Fabio M. De Francesco <fmdefrancesco@gmail.com>
Acked-by: Karsten Graul <kgraul@linux.ibm.com>
Link: https://lore.kernel.org/r/20220223100252.22562-1-fmdefrancesco@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Fix following coccicheck warning:
./net/sched/act_api.c:277:7-49: WARNING avoid newline at end of message
in NL_SET_ERR_MSG_MOD
Signed-off-by: Wan Jiabing <wanjiabing@vivo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These tests are supposed to check if the loop exited via a break or not.
However the tests are wrong because if we did not exit via a break then
"p" is not a valid pointer. In that case, it's the equivalent of
"if (*(u32 *)sr == *last_key) {". That's going to work most of the time,
but there is a potential for those to be equal.
Fixes: 1593123a6a ("tipc: add name table dump to new netlink api")
Fixes: 1a1a143daf ("tipc: add publication dump to new netlink api")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This test is checking if we exited the list via break or not. However
if it did not exit via a break then "node" does not point to a valid
udp_tunnel_nic_shared_node struct. It will work because of the way
the structs are laid out it's the equivalent of
"if (info->shared->udp_tunnel_nic_info != dev)" which will always be
true, but it's not the right way to test.
Fixes: 74cc6d182d ("udp_tunnel: add the ability to share port tables")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If a bridged port is not offloaded to the hardware - either because the
underlying driver does not implement the port_bridge_{join,leave} ops,
or because the operation failed - then its dp->bridge pointer will be
NULL when dsa_port_bridge_leave() is called. Avoid dereferncing NULL.
This fixes the following splat when removing a port from a bridge:
Unable to handle kernel access to user memory outside uaccess routines at virtual address 0000000000000000
Internal error: Oops: 96000004 [#1] PREEMPT_RT SMP
CPU: 3 PID: 1119 Comm: brctl Tainted: G O 5.17.0-rc4-rt4 #1
Call trace:
dsa_port_bridge_leave+0x8c/0x1e4
dsa_slave_changeupper+0x40/0x170
dsa_slave_netdevice_event+0x494/0x4d4
notifier_call_chain+0x80/0xe0
raw_notifier_call_chain+0x1c/0x24
call_netdevice_notifiers_info+0x5c/0xac
__netdev_upper_dev_unlink+0xa4/0x200
netdev_upper_dev_unlink+0x38/0x60
del_nbp+0x1b0/0x300
br_del_if+0x38/0x114
add_del_if+0x60/0xa0
br_ioctl_stub+0x128/0x2dc
br_ioctl_call+0x68/0xb0
dev_ifsioc+0x390/0x554
dev_ioctl+0x128/0x400
sock_do_ioctl+0xb4/0xf4
sock_ioctl+0x12c/0x4e0
__arm64_sys_ioctl+0xa8/0xf0
invoke_syscall+0x4c/0x110
el0_svc_common.constprop.0+0x48/0xf0
do_el0_svc+0x28/0x84
el0_svc+0x1c/0x50
el0t_64_sync_handler+0xa8/0xb0
el0t_64_sync+0x17c/0x180
Code: f9402f00 f0002261 f9401302 913cc021 (a9401404)
---[ end trace 0000000000000000 ]---
Fixes: d3eed0e57d ("net: dsa: keep the bridge_dev and bridge_num as part of the same structure")
Signed-off-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20220221203539.310690-1-alvin@pqrs.dk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Whenever one of these functions pull all data from an skb in a frag_list,
use consume_skb() instead of kfree_skb() to avoid polluting drop
monitoring.
Fixes: 6fa01ccd88 ("skbuff: Add pskb_extract() helper function")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Link: https://lore.kernel.org/r/20220220154052.1308469-1-eric.dumazet@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Pablo Neira Ayuso says:
====================
Netfilter fixes for net
This is fixing up the use without proper initialization in patch 5/5
-o-
Hi,
The following patchset contains Netfilter fixes for net:
1) Missing #ifdef CONFIG_IP6_NF_IPTABLES in recent xt_socket fix.
2) Fix incorrect flow action array size in nf_tables.
3) Unregister flowtable hooks from netns exit path.
4) Fix missing limit object release, from Florian Westphal.
5) Memleak in nf_tables object update path, also from Florian.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
stateful objects can be updated from the control plane.
The transaction logic allocates a temporary object for this purpose.
The ->init function was called for this object, so plain kfree() leaks
resources. We must call ->destroy function of the object.
nft_obj_destroy does this, but it also decrements the module refcount,
but the update path doesn't increment it.
To avoid special-casing the update object release, do module_get for
the update case too and release it via nft_obj_destroy().
Fixes: d62d0ba97b ("netfilter: nf_tables: Introduce stateful object update operation")
Cc: Fernando Fernandez Mancera <ffmancera@riseup.net>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
We need to provide a destroy callback to release the extra fields.
Fixes: 3b9e2ea6c1 ("netfilter: nft_limit: move stateful fields out of expression data")
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Unregister flowtable hooks before they are releases via
nf_tables_flowtable_destroy() otherwise hook core reports UAF.
BUG: KASAN: use-after-free in nf_hook_entries_grow+0x5a7/0x700 net/netfilter/core.c:142 net/netfilter/core.c:142
Read of size 4 at addr ffff8880736f7438 by task syz-executor579/3666
CPU: 0 PID: 3666 Comm: syz-executor579 Not tainted 5.16.0-rc5-syzkaller #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Call Trace:
<TASK>
__dump_stack lib/dump_stack.c:88 [inline]
__dump_stack lib/dump_stack.c:88 [inline] lib/dump_stack.c:106
dump_stack_lvl+0x1dc/0x2d8 lib/dump_stack.c:106 lib/dump_stack.c:106
print_address_description+0x65/0x380 mm/kasan/report.c:247 mm/kasan/report.c:247
__kasan_report mm/kasan/report.c:433 [inline]
__kasan_report mm/kasan/report.c:433 [inline] mm/kasan/report.c:450
kasan_report+0x19a/0x1f0 mm/kasan/report.c:450 mm/kasan/report.c:450
nf_hook_entries_grow+0x5a7/0x700 net/netfilter/core.c:142 net/netfilter/core.c:142
__nf_register_net_hook+0x27e/0x8d0 net/netfilter/core.c:429 net/netfilter/core.c:429
nf_register_net_hook+0xaa/0x180 net/netfilter/core.c:571 net/netfilter/core.c:571
nft_register_flowtable_net_hooks+0x3c5/0x730 net/netfilter/nf_tables_api.c:7232 net/netfilter/nf_tables_api.c:7232
nf_tables_newflowtable+0x2022/0x2cf0 net/netfilter/nf_tables_api.c:7430 net/netfilter/nf_tables_api.c:7430
nfnetlink_rcv_batch net/netfilter/nfnetlink.c:513 [inline]
nfnetlink_rcv_skb_batch net/netfilter/nfnetlink.c:634 [inline]
nfnetlink_rcv_batch net/netfilter/nfnetlink.c:513 [inline] net/netfilter/nfnetlink.c:652
nfnetlink_rcv_skb_batch net/netfilter/nfnetlink.c:634 [inline] net/netfilter/nfnetlink.c:652
nfnetlink_rcv+0x10e6/0x2550 net/netfilter/nfnetlink.c:652 net/netfilter/nfnetlink.c:652
__nft_release_hook() calls nft_unregister_flowtable_net_hooks() which
only unregisters the hooks, then after RCU grace period, it is
guaranteed that no packets add new entries to the flowtable (no flow
offload rules and flowtable hooks are reachable from packet path), so it
is safe to call nf_flow_table_free() which cleans up the remaining
entries from the flowtable (both software and hardware) and it unbinds
the flow_block.
Fixes: ff4bf2f42a ("netfilter: nf_tables: add nft_unregister_flowtable_hook()")
Reported-by: syzbot+e918523f77e62790d6d9@syzkaller.appspotmail.com
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
We encounter a tcp drop issue in our cloud environment. Packet GROed in
host forwards to a VM virtio_net nic with net_failover enabled. VM acts
as a IPVS LB with ipip encapsulation. The full path like:
host gro -> vm virtio_net rx -> net_failover rx -> ipvs fullnat
-> ipip encap -> net_failover tx -> virtio_net tx
When net_failover transmits a ipip pkt (gso_type = 0x0103, which means
SKB_GSO_TCPV4, SKB_GSO_DODGY and SKB_GSO_IPXIP4), there is no gso
did because it supports TSO and GSO_IPXIP4. But network_header points to
inner ip header.
Call Trace:
tcp4_gso_segment ------> return NULL
inet_gso_segment ------> inner iph, network_header points to
ipip_gso_segment
inet_gso_segment ------> outer iph
skb_mac_gso_segment
Afterwards virtio_net transmits the pkt, only inner ip header is modified.
And the outer one just keeps unchanged. The pkt will be dropped in remote
host.
Call Trace:
inet_gso_segment ------> inner iph, outer iph is skipped
skb_mac_gso_segment
__skb_gso_segment
validate_xmit_skb
validate_xmit_skb_list
sch_direct_xmit
__qdisc_run
__dev_queue_xmit ------> virtio_net
dev_hard_start_xmit
__dev_queue_xmit ------> net_failover
ip_finish_output2
ip_output
iptunnel_xmit
ip_tunnel_xmit
ipip_tunnel_xmit ------> ipip
dev_hard_start_xmit
__dev_queue_xmit
ip_finish_output2
ip_output
ip_forward
ip_rcv
__netif_receive_skb_one_core
netif_receive_skb_internal
napi_gro_receive
receive_buf
virtnet_poll
net_rx_action
The root cause of this issue is specific with the rare combination of
SKB_GSO_DODGY and a tunnel device that adds an SKB_GSO_ tunnel option.
SKB_GSO_DODGY is set from external virtio_net. We need to reset network
header when callbacks.gso_segment() returns NULL.
This patch also includes ipv6_gso_segment(), considering SIT, etc.
Fixes: cb32f511a7 ("ipip: add GSO/TSO support")
Signed-off-by: Tao Liu <thomas.liu@ucloud.cn>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
immediate verdict expression needs to allocate one slot in the flow offload
action array, however, immediate data expression does not need to do so.
fwd and dup expression need to allocate one slot, this is missing.
Add a new offload_action interface to report if this expression needs to
allocate one slot in the flow offload action array.
Fixes: be2861dc36 ("netfilter: nft_{fwd,dup}_netdev: add offload support")
Reported-and-tested-by: Nick Gregory <Nick.Gregory@Sophos.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
If the DSA master doesn't support IFF_UNICAST_FLT, then the following
call path is possible:
dsa_slave_switchdev_event_work
-> dsa_port_host_fdb_add
-> dev_uc_add
-> __dev_set_rx_mode
-> __dev_set_promiscuity
Since the blamed commit, dsa_slave_switchdev_event_work() no longer
holds rtnl_lock(), which triggers the ASSERT_RTNL() from
__dev_set_promiscuity().
Taking rtnl_lock() around dev_uc_add() is impossible, because all the
code paths that call dsa_flush_workqueue() do so from contexts where the
rtnl_mutex is already held - so this would lead to an instant deadlock.
dev_uc_add() in itself doesn't require the rtnl_mutex for protection.
There is this comment in __dev_set_rx_mode() which assumes so:
/* Unicast addresses changes may only happen under the rtnl,
* therefore calling __dev_set_promiscuity here is safe.
*/
but it is from commit 4417da668c ("[NET]: dev: secondary unicast
address support") dated June 2007, and in the meantime, commit
f1f28aa351 ("netdev: Add addr_list_lock to struct net_device."), dated
July 2008, has added &dev->addr_list_lock to protect this instead of the
global rtnl_mutex.
Nonetheless, __dev_set_promiscuity() does assume rtnl_mutex protection,
but it is the uncommon path of what we typically expect dev_uc_add()
to do. So since only the uncommon path requires rtnl_lock(), just check
ahead of time whether dev_uc_add() would result into a call to
__dev_set_promiscuity(), and handle that condition separately.
DSA already configures the master interface to be promiscuous if the
tagger requires this. We can extend this to also cover the case where
the master doesn't handle dev_uc_add() (doesn't support IFF_UNICAST_FLT),
and on the premise that we'd end up making it promiscuous during
operation anyway, either if a DSA slave has a non-inherited MAC address,
or if the bridge notifies local FDB entries for its own MAC address, the
address of a station learned on a foreign port, etc.
Fixes: 0faf890fc5 ("net: dsa: drop rtnl_lock from dsa_slave_switchdev_event_work")
Reported-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MPTCP in kernel path manager has some constraints on incoming
addresses announce processing, so that in edge scenarios it can
end-up dropping (ignoring) some of such announces.
The above is not very limiting in practice since such scenarios are
very uncommon and MPTCP will recover due to ADD_ADDR retransmissions.
This patch adds a few MIB counters to account for such drop events
to allow easier introspection of the critical scenarios.
Fixes: f7efc7771e ("mptcp: drop argument port from mptcp_pm_announce_addr")
Reviewed-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If an MPTCP endpoint received multiple consecutive incoming
ADD_ADDR options, mptcp_pm_add_addr_received() can overwrite
the current remote address value after the PM lock is released
in mptcp_pm_nl_add_addr_received() and before such address
is echoed.
Fix the issue caching the remote address value a little earlier
and always using the cached value after releasing the PM lock.
Fixes: f7efc7771e ("mptcp: drop argument port from mptcp_pm_announce_addr")
Reviewed-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After commit a88c9e4969 ("mptcp: do not block subflows
creation on errors"), if a signal address races with a failing
subflow creation, the subflow creation failure control path
can trigger the selection of the next address to be announced
while the current announced is still pending.
The above will cause the unintended suppression of the ADD_ADDR
announce.
Fix the issue skipping the to-be-suppressed announce before it
will mark an endpoint as already used. The relevant announce
will be triggered again when the current one will complete.
Fixes: a88c9e4969 ("mptcp: do not block subflows creation on errors")
Reviewed-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
UDP sendmsg() can be lockless, this is causing all kinds
of data races.
This patch converts sk->sk_tskey to remove one of these races.
BUG: KCSAN: data-race in __ip_append_data / __ip_append_data
read to 0xffff8881035d4b6c of 4 bytes by task 8877 on cpu 1:
__ip_append_data+0x1c1/0x1de0 net/ipv4/ip_output.c:994
ip_make_skb+0x13f/0x2d0 net/ipv4/ip_output.c:1636
udp_sendmsg+0x12bd/0x14c0 net/ipv4/udp.c:1249
inet_sendmsg+0x5f/0x80 net/ipv4/af_inet.c:819
sock_sendmsg_nosec net/socket.c:705 [inline]
sock_sendmsg net/socket.c:725 [inline]
____sys_sendmsg+0x39a/0x510 net/socket.c:2413
___sys_sendmsg net/socket.c:2467 [inline]
__sys_sendmmsg+0x267/0x4c0 net/socket.c:2553
__do_sys_sendmmsg net/socket.c:2582 [inline]
__se_sys_sendmmsg net/socket.c:2579 [inline]
__x64_sys_sendmmsg+0x53/0x60 net/socket.c:2579
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x44/0xd0 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x44/0xae
write to 0xffff8881035d4b6c of 4 bytes by task 8880 on cpu 0:
__ip_append_data+0x1d8/0x1de0 net/ipv4/ip_output.c:994
ip_make_skb+0x13f/0x2d0 net/ipv4/ip_output.c:1636
udp_sendmsg+0x12bd/0x14c0 net/ipv4/udp.c:1249
inet_sendmsg+0x5f/0x80 net/ipv4/af_inet.c:819
sock_sendmsg_nosec net/socket.c:705 [inline]
sock_sendmsg net/socket.c:725 [inline]
____sys_sendmsg+0x39a/0x510 net/socket.c:2413
___sys_sendmsg net/socket.c:2467 [inline]
__sys_sendmmsg+0x267/0x4c0 net/socket.c:2553
__do_sys_sendmmsg net/socket.c:2582 [inline]
__se_sys_sendmmsg net/socket.c:2579 [inline]
__x64_sys_sendmmsg+0x53/0x60 net/socket.c:2579
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x44/0xd0 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x44/0xae
value changed: 0x0000054d -> 0x0000054e
Reported by Kernel Concurrency Sanitizer on:
CPU: 0 PID: 8880 Comm: syz-executor.5 Not tainted 5.17.0-rc2-syzkaller-00167-gdcb85f85fa6f-dirty #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Fixes: 09c2d251b7 ("net-timestamp: add key to disambiguate concurrent datagrams")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Willem de Bruijn <willemb@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Flow table lookup is skipped if packet either went through ct clear
action (which set the IP_CT_UNTRACKED flag on the packet), or while
switching zones and there is already a connection associated with
the packet. This will result in no SW offload of the connection,
and the and connection not being removed from flow table with
TCP teardown (fin/rst packet).
To fix the above, remove these unneccary checks in flow
table lookup.
Fixes: 46475bb20f ("net/sched: act_ct: Software offload of established flows")
Signed-off-by: Paul Blakey <paulb@nvidia.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When bringing down the netdevice or system shutdown, a panic can be
triggered while accessing the sysfs path because the device is already
removed.
[ 755.549084] mlx5_core 0000:12:00.1: Shutdown was called
[ 756.404455] mlx5_core 0000:12:00.0: Shutdown was called
...
[ 757.937260] BUG: unable to handle kernel NULL pointer dereference at (null)
[ 758.031397] IP: [<ffffffff8ee11acb>] dma_pool_alloc+0x1ab/0x280
crash> bt
...
PID: 12649 TASK: ffff8924108f2100 CPU: 1 COMMAND: "amsd"
...
#9 [ffff89240e1a38b0] page_fault at ffffffff8f38c778
[exception RIP: dma_pool_alloc+0x1ab]
RIP: ffffffff8ee11acb RSP: ffff89240e1a3968 RFLAGS: 00010046
RAX: 0000000000000246 RBX: ffff89243d874100 RCX: 0000000000001000
RDX: 0000000000000000 RSI: 0000000000000246 RDI: ffff89243d874090
RBP: ffff89240e1a39c0 R8: 000000000001f080 R9: ffff8905ffc03c00
R10: ffffffffc04680d4 R11: ffffffff8edde9fd R12: 00000000000080d0
R13: ffff89243d874090 R14: ffff89243d874080 R15: 0000000000000000
ORIG_RAX: ffffffffffffffff CS: 0010 SS: 0018
#10 [ffff89240e1a39c8] mlx5_alloc_cmd_msg at ffffffffc04680f3 [mlx5_core]
#11 [ffff89240e1a3a18] cmd_exec at ffffffffc046ad62 [mlx5_core]
#12 [ffff89240e1a3ab8] mlx5_cmd_exec at ffffffffc046b4fb [mlx5_core]
#13 [ffff89240e1a3ae8] mlx5_core_access_reg at ffffffffc0475434 [mlx5_core]
#14 [ffff89240e1a3b40] mlx5e_get_fec_caps at ffffffffc04a7348 [mlx5_core]
#15 [ffff89240e1a3bb0] get_fec_supported_advertised at ffffffffc04992bf [mlx5_core]
#16 [ffff89240e1a3c08] mlx5e_get_link_ksettings at ffffffffc049ab36 [mlx5_core]
#17 [ffff89240e1a3ce8] __ethtool_get_link_ksettings at ffffffff8f25db46
#18 [ffff89240e1a3d48] speed_show at ffffffff8f277208
#19 [ffff89240e1a3dd8] dev_attr_show at ffffffff8f0b70e3
#20 [ffff89240e1a3df8] sysfs_kf_seq_show at ffffffff8eedbedf
#21 [ffff89240e1a3e18] kernfs_seq_show at ffffffff8eeda596
#22 [ffff89240e1a3e28] seq_read at ffffffff8ee76d10
#23 [ffff89240e1a3e98] kernfs_fop_read at ffffffff8eedaef5
#24 [ffff89240e1a3ed8] vfs_read at ffffffff8ee4e3ff
#25 [ffff89240e1a3f08] sys_read at ffffffff8ee4f27f
#26 [ffff89240e1a3f50] system_call_fastpath at ffffffff8f395f92
crash> net_device.state ffff89443b0c0000
state = 0x5 (__LINK_STATE_START| __LINK_STATE_NOCARRIER)
To prevent this scenario, we also make sure that the netdevice is present.
Signed-off-by: suresh kumar <suresh2514@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexei Starovoitov says:
====================
pull-request: bpf 2022-02-17
We've added 8 non-merge commits during the last 7 day(s) which contain
a total of 8 files changed, 119 insertions(+), 15 deletions(-).
The main changes are:
1) Add schedule points in map batch ops, from Eric.
2) Fix bpf_msg_push_data with len 0, from Felix.
3) Fix crash due to incorrect copy_map_value, from Kumar.
4) Fix crash due to out of bounds access into reg2btf_ids, from Kumar.
5) Fix a bpf_timer initialization issue with clang, from Yonghong.
* https://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf:
bpf: Add schedule points in batch ops
bpf: Fix crash due to out of bounds access into reg2btf_ids.
selftests: bpf: Check bpf_msg_push_data return value
bpf: Fix a bpf_timer initialization issue
bpf: Emit bpf_timer in vmlinux BTF
selftests/bpf: Add test for bpf_timer overwriting crash
bpf: Fix crash due to incorrect copy_map_value
bpf: Do not try bpf_msg_push_data with len 0
====================
Link: https://lore.kernel.org/r/20220217190000.37925-1-alexei.starovoitov@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
fib_alias_hw_flags_set() can be used by concurrent threads,
and is only RCU protected.
We need to annotate accesses to following fields of struct fib_alias:
offload, trap, offload_failed
Because of READ_ONCE()WRITE_ONCE() limitations, make these
field u8.
BUG: KCSAN: data-race in fib_alias_hw_flags_set / fib_alias_hw_flags_set
read to 0xffff888134224a6a of 1 bytes by task 2013 on cpu 1:
fib_alias_hw_flags_set+0x28a/0x470 net/ipv4/fib_trie.c:1050
nsim_fib4_rt_hw_flags_set drivers/net/netdevsim/fib.c:350 [inline]
nsim_fib4_rt_add drivers/net/netdevsim/fib.c:367 [inline]
nsim_fib4_rt_insert drivers/net/netdevsim/fib.c:429 [inline]
nsim_fib4_event drivers/net/netdevsim/fib.c:461 [inline]
nsim_fib_event drivers/net/netdevsim/fib.c:881 [inline]
nsim_fib_event_work+0x1852/0x2cf0 drivers/net/netdevsim/fib.c:1477
process_one_work+0x3f6/0x960 kernel/workqueue.c:2307
process_scheduled_works kernel/workqueue.c:2370 [inline]
worker_thread+0x7df/0xa70 kernel/workqueue.c:2456
kthread+0x1bf/0x1e0 kernel/kthread.c:377
ret_from_fork+0x1f/0x30
write to 0xffff888134224a6a of 1 bytes by task 4872 on cpu 0:
fib_alias_hw_flags_set+0x2d5/0x470 net/ipv4/fib_trie.c:1054
nsim_fib4_rt_hw_flags_set drivers/net/netdevsim/fib.c:350 [inline]
nsim_fib4_rt_add drivers/net/netdevsim/fib.c:367 [inline]
nsim_fib4_rt_insert drivers/net/netdevsim/fib.c:429 [inline]
nsim_fib4_event drivers/net/netdevsim/fib.c:461 [inline]
nsim_fib_event drivers/net/netdevsim/fib.c:881 [inline]
nsim_fib_event_work+0x1852/0x2cf0 drivers/net/netdevsim/fib.c:1477
process_one_work+0x3f6/0x960 kernel/workqueue.c:2307
process_scheduled_works kernel/workqueue.c:2370 [inline]
worker_thread+0x7df/0xa70 kernel/workqueue.c:2456
kthread+0x1bf/0x1e0 kernel/kthread.c:377
ret_from_fork+0x1f/0x30
value changed: 0x00 -> 0x02
Reported by Kernel Concurrency Sanitizer on:
CPU: 0 PID: 4872 Comm: kworker/0:0 Not tainted 5.17.0-rc3-syzkaller-00188-g1d41d2e82623-dirty #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Workqueue: events nsim_fib_event_work
Fixes: 90b93f1b31 ("ipv4: Add "offload" and "trap" indications to routes")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Link: https://lore.kernel.org/r/20220216173217.3792411-1-eric.dumazet@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Check for a hwaccel VLAN tag on rx and use it if present. Otherwise,
use __skb_vlan_pop() like the other tag parsers do. This fixes the case
where the VLAN tag has already been consumed by the master.
Fixes: a1292595e0 ("net: dsa: add new DSA switch driver for the SMSC-LAN9303")
Signed-off-by: Mans Rullgard <mans@mansr.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://lore.kernel.org/r/20220216124634.23123-1-mans@mansr.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
vsock_connect() expects that the socket could already be in the
TCP_ESTABLISHED state when the connecting task wakes up with a signal
pending. If this happens the socket will be in the connected table, and
it is not removed when the socket state is reset. In this situation it's
common for the process to retry connect(), and if the connection is
successful the socket will be added to the connected table a second
time, corrupting the list.
Prevent this by calling vsock_remove_connected() if a signal is received
while waiting for a connection. This is harmless if the socket is not in
the connected table, and if it is in the table then removing it will
prevent list corruption from a double add.
Note for backporting: this patch requires d5afa82c97 ("vsock: correct
removal of socket from the list"), which is in all current stable trees
except 4.9.y.
Fixes: d021c34405 ("VSOCK: Introduce VM Sockets")
Signed-off-by: Seth Forshee <sforshee@digitalocean.com>
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Link: https://lore.kernel.org/r/20220217141312.2297547-1-sforshee@digitalocean.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When 'ping' changes to use PING socket instead of RAW socket by:
# sysctl -w net.ipv4.ping_group_range="0 100"
There is another regression caused when matching sk_bound_dev_if
and dif, RAW socket is using inet_iif() while PING socket lookup
is using skb->dev->ifindex, the cmd below fails due to this:
# ip link add dummy0 type dummy
# ip link set dummy0 up
# ip addr add 192.168.111.1/24 dev dummy0
# ping -I dummy0 192.168.111.1 -c1
The issue was also reported on:
https://github.com/iputils/iputils/issues/104
But fixed in iputils in a wrong way by not binding to device when
destination IP is on device, and it will cause some of kselftests
to fail, as Jianlin noticed.
This patch is to use inet(6)_iif and inet(6)_sdif to get dif and
sdif for PING socket, and keep consistent with RAW socket.
Fixes: c319b4d76b ("net: ipv4: add IPPROTO_ICMP socket kind")
Reported-by: Jianlin Shi <jishi@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The previous bug fix had an unfortunate side effect that broke
distribution of binding table entries between nodes. The updated
tipc_sock_addr struct is also used further down in the same
function, and there the old value is still the correct one.
Fixes: 032062f363 ("tipc: fix wrong publisher node address in link publications")
Signed-off-by: Jon Maloy <jmaloy@redhat.com>
Link: https://lore.kernel.org/r/20220216020009.3404578-1-jmaloy@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Ipv6 flowlabels historically require a reservation before use.
Optionally in exclusive mode (e.g., user-private).
Commit 59c820b231 ("ipv6: elide flowlabel check if no exclusive
leases exist") introduced a fastpath that avoids this check when no
exclusive leases exist in the system, and thus any flowlabel use
will be granted.
That allows skipping the control operation to reserve a flowlabel
entirely. Though with a warning if the fast path fails:
This is an optimization. Robust applications still have to revert to
requesting leases if the fast path fails due to an exclusive lease.
Still, this is subtle. Better isolate network namespaces from each
other. Flowlabels are per-netns. Also record per-netns whether
exclusive leases are in use. Then behavior does not change based on
activity in other netns.
Changes
v2
- wrap in IS_ENABLED(CONFIG_IPV6) to avoid breakage if disabled
Fixes: 59c820b231 ("ipv6: elide flowlabel check if no exclusive leases exist")
Link: https://lore.kernel.org/netdev/MWHPR2201MB1072BCCCFCE779E4094837ACD0329@MWHPR2201MB1072.namprd22.prod.outlook.com/
Reported-by: Congyu Liu <liu3101@purdue.edu>
Signed-off-by: Willem de Bruijn <willemb@google.com>
Tested-by: Congyu Liu <liu3101@purdue.edu>
Link: https://lore.kernel.org/r/20220215160037.1976072-1-willemdebruijn.kernel@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Whenever bridge driver hits the max capacity of MDBs, it disables
the MC processing (by setting corresponding bridge option), but never
notifies switchdev about such change (the notifiers are called only upon
explicit setting of this option, through the registered netlink interface).
This could lead to situation when Software MDB processing gets disabled,
but this event never gets offloaded to the underlying Hardware.
Fix this by adding a notify message in such case.
Fixes: 147c1e9b90 ("switchdev: bridge: Offload multicast disabled")
Signed-off-by: Oleksandr Mazur <oleksandr.mazur@plvision.eu>
Acked-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Link: https://lore.kernel.org/r/20220215165303.31908-1-oleksandr.mazur@plvision.eu
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Clang static analysis reports this problem
route.c:425:4: warning: Use of memory after it is freed
trace_mctp_key_acquire(key);
^~~~~~~~~~~~~~~~~~~~~~~~~~~
When mctp_key_add() fails, key is freed but then is later
used in trace_mctp_key_acquire(). Add an else statement
to use the key only when mctp_key_add() is successful.
Fixes: 4f9e1ba6de ("mctp: Add tracepoints for tag/key handling")
Signed-off-by: Tom Rix <trix@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When multiple containers are running in the environment and multiple
macvlan network port are configured in each container, a lot of martian
source prints will appear after martian_log is enabled. they are almost
the same, and printed by net_warn_ratelimited. Each arp message will
trigger this print on each network port.
Such as:
IPv4: martian source 173.254.95.16 from 173.254.100.109,
on dev eth0
ll header: 00000000: ff ff ff ff ff ff 40 00 ad fe 64 6d
08 06 ......@...dm..
IPv4: martian source 173.254.95.16 from 173.254.100.109,
on dev eth1
ll header: 00000000: ff ff ff ff ff ff 40 00 ad fe 64 6d
08 06 ......@...dm..
There is no description of this kind of source in the RFC1812.
Signed-off-by: Zhang Yunkai <zhang.yunkai@zte.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a link comes up we add its presence to the name table to make it
possible for users to subscribe for link up/down events. However, after
a previous call signature change the binding is wrongly published with
the peer node as publishing node, instead of the own node as it should
be. This has the effect that the command 'tipc name table show' will
list the link binding (service type 2) with node scope and a peer node
as originator, something that obviously is impossible.
We correct this bug here.
Fixes: 50a3499ab8 ("tipc: simplify signature of tipc_namtbl_publish()")
Signed-off-by: Jon Maloy <jmaloy@redhat.com>
Link: https://lore.kernel.org/r/20220214013852.2803940-1-jmaloy@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Fixes return value documentation of kernel_getsockname()
and kernel_getpeername() functions.
The previous documentation wrongly specified that the return
value is 0 in case of success, however sock->ops->getname returns
the length of the address in bytes in case of success.
Signed-off-by: Alex Maydanik <alexander.maydanik@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
mv88e6xxx is special among DSA drivers in that it requires the VTU to
contain the VID of the FDB entry it modifies in
mv88e6xxx_port_db_load_purge(), otherwise it will return -EOPNOTSUPP.
Sometimes due to races this is not always satisfied even if external
code does everything right (first deletes the FDB entries, then the
VLAN), because DSA commits to hardware FDB entries asynchronously since
commit c9eb3e0f87 ("net: dsa: Add support for learning FDB through
notification").
Therefore, the mv88e6xxx driver must close this race condition by
itself, by asking DSA to flush the switchdev workqueue of any FDB
deletions in progress, prior to exiting a VLAN.
Fixes: c9eb3e0f87 ("net: dsa: Add support for learning FDB through notification")
Reported-by: Rafael Richter <rafael.richter@gin.de>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
nf_defrag_ipv6_disable() requires CONFIG_IP6_NF_IPTABLES.
Fixes: 75063c9294 ("netfilter: xt_socket: fix a typo in socket_mt_destroy()")
Reported-by: kernel test robot <lkp@intel.com>
Reviewed-by: Eric Dumazet<edumazet@google.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
