ksets contain a kobject and they should always be allocated dynamically,
because it is unknown to whoever creates them when ksets can be
released.
Signed-off-by: Riccardo Schirone <sirmy15@gmail.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
kobjects should always be allocated dynamically, because it is unknown
to whoever creates them when kobjects can be released.
Signed-off-by: Riccardo Schirone <sirmy15@gmail.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Even when kobject_init_and_add/kset_register fail, the kobject has been
already initialized and the refcount set to 1. Thus it is necessary to
release the kobject/kset, to avoid the memory associated with it hanging
around forever.
Signed-off-by: Riccardo Schirone <sirmy15@gmail.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
The indentation is incorrect and spaces need replacing with a tab
on the if statement.
Cleans up smatch warning:
fs/ext4/namei.c:3220 ext4_link() warn: inconsistent indenting
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Reviewed-by: Jan Kara <jack@suse.cz>
We could use 'sbi' instead of 'EXT4_SB(sb)' to make code more elegant.
Signed-off-by: Jun Piao <piaojun@huawei.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Reviewed-by: Jan Kara <jack@suse.cz>
In the function __ext4_grp_locked_error(), __save_error_info()
is called to save error info in super block block, but does not sync
that information to disk to info the subsequence fsck after reboot.
This patch writes the error information to disk. After this patch,
I think there is no obvious EXT4 error handle branches which leads to
"Remounting filesystem read-only" will leave the disk partition miss
the subsequence fsck.
Signed-off-by: Zhouyi Zhou <zhouzhouyi@gmail.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Cc: stable@vger.kernel.org
This patch fixes a race between the shutdown path and bio completion
handling. In the ext4 direct io path with async io, after submitting a
bio to the block layer, if journal starting fails,
ext4_direct_IO_write() would bail out pretending that the IO
failed. The caller would have had no way of knowing whether or not the
IO was successfully submitted. So instead, we return -EIOCBQUEUED in
this case. Now, the caller knows that the IO was submitted. The bio
completion handler takes care of the error.
Tested: Ran the shutdown xfstest test 461 in loop for over 2 hours across
4 machines resulting in over 400 runs. Verified that the race didn't
occur. Usually the race was seen in about 20-30 iterations.
Signed-off-by: Harshad Shirwadkar <harshads@google.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Cc: stable@vger.kernel.org
destroy_workqueue() will do flushing work for us.
Signed-off-by: Jun Piao <piaojun@huawei.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Reviewed-by: Jan Kara <jack@suse.cz>
When allocation of underlying block for a page fault fails, we fail the
fault with SIGBUS. However we may well hit ENOSPC just due to lots of
free blocks being held by the running / committing transaction. So
propagate the error from ext4_iomap_begin() and implement do standard
allocation retry loop in ext4_dax_huge_fault().
Reviewed-by: Ross Zwisler <ross.zwisler@linux.intel.com>
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Ext4 needs to pass through error from its iomap handler to the page
fault handler so that it can properly detect ENOSPC and force
transaction commit and retry the fault (and block allocation). Add
argument to dax_iomap_fault() for passing such error.
Reviewed-by: Ross Zwisler <ross.zwisler@linux.intel.com>
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
This link is replicated in most filesystems' config stanzas. Referring
to an archived version of that site is pointless as it mostly deals with
patches; user documentation is available elsewhere.
Signed-off-by: Adam Borowski <kilobyte@angband.pl>
CC: Alexander Viro <viro@zeniv.linux.org.uk>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Acked-by: Jan Kara <jack@suse.cz>
Acked-by: Dave Kleikamp <dave.kleikamp@oracle.com>
Acked-by: David Sterba <dsterba@suse.com>
Acked-by: "Yan, Zheng" <zyan@redhat.com>
Acked-by: Chao Yu <yuchao0@huawei.com>
Acked-by: Jaegeuk Kim <jaegeuk@kernel.org>
Acked-by: Steve French <smfrench@gmail.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
A number of ext4 source files were skipped due because their copyright
permission statements didn't match the expected text used by the
automated conversion utilities. I've added SPDX tags for the rest.
While looking at some of these files, I've noticed that we have quite
a bit of variation on the licenses that were used --- in particular
some of the Red Hat licenses on the jbd2 files use a GPL2+ license,
and we have some files that have a LGPL-2.1 license (which was quite
surprising).
I've not attempted to do any license changes. Even if it is perfectly
legal to relicense to GPL 2.0-only for consistency's sake, that should
be done with ext4 developer community discussion.
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
On a ppc64 machine, when mounting a fuzzed ext2 image (generated by
fsfuzzer) the following call trace is seen,
VFS: brelse: Trying to free free buffer
WARNING: CPU: 1 PID: 6913 at /root/repos/linux/fs/buffer.c:1165 .__brelse.part.6+0x24/0x40
.__brelse.part.6+0x20/0x40 (unreliable)
.ext4_find_entry+0x384/0x4f0
.ext4_lookup+0x84/0x250
.lookup_slow+0xdc/0x230
.walk_component+0x268/0x400
.path_lookupat+0xec/0x2d0
.filename_lookup+0x9c/0x1d0
.vfs_statx+0x98/0x140
.SyS_newfstatat+0x48/0x80
system_call+0x58/0x6c
This happens because the directory that ext4_find_entry() looks up has
inode->i_size that is less than the block size of the filesystem. This
causes 'nblocks' to have a value of zero. ext4_bread_batch() ends up not
reading any of the directory file's blocks. This renders the entries in
bh_use[] array to continue to have garbage data. buffer_uptodate() on
bh_use[0] can then return a zero value upon which brelse() function is
invoked.
This commit fixes the bug by returning -ENOENT when the directory file
has no associated blocks.
Reported-by: Abdul Haleem <abdhalee@linux.vnet.ibm.com>
Signed-off-by: Chandan Rajendra <chandan@linux.vnet.ibm.com>
Cc: stable@vger.kernel.org
It's possible for ext4_get_acl() to return an ERR_PTR. So we need to
add a check for this case in __ext4_new_inode(). Otherwise on an
error we can end up oops the kernel.
This was getting triggered by xfstests generic/388, which is a test
which exercises the shutdown code path.
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Cc: stable@vger.kernel.org
Currently, fallocate(2) with KEEP_SIZE followed by a fdatasync(2)
then crash, we'll see wrong allocated block number (stat -c %b), the
blocks allocated beyond EOF are all lost. fstests generic/468
exposes this bug.
Commit 67a7d5f561 ("ext4: fix fdatasync(2) after extent
manipulation operations") fixed all the other extent manipulation
operation paths such as hole punch, zero range, collapse range etc.,
but forgot the fallocate case.
So similarly, fix it by recording the correct journal tid in ext4
inode in fallocate(2) path, so that ext4_sync_file() will wait for
the right tid to be committed on fdatasync(2).
This addresses the test failure in xfstests test generic/468.
Signed-off-by: Eryu Guan <eguan@redhat.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Cc: stable@vger.kernel.org
407cd7fb83 (ext4: change fast symlink test to not rely on i_blocks)
broke ~10 years old ext3 file systems created by 2.6.17. Any ELF
executable fails because the /lib/ld-linux.so.2 fast symlink
cannot be read anymore.
The patch assumed fast symlinks were created in a specific way,
but that's not true on these really old file systems.
The new behavior is apparently needed only with the large EA inode
feature.
Revert to the old behavior if the large EA inode feature is not set.
This makes my old VM boot again.
Fixes: 407cd7fb83 (ext4: change fast symlink test to not rely on i_blocks)
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Reviewed-by: Andreas Dilger <adilger@dilger.ca>
Cc: stable@vger.kernel.org
This is a pure automated search-and-replace of the internal kernel
superblock flags.
The s_flags are now called SB_*, with the names and the values for the
moment mirroring the MS_* flags that they're equivalent to.
Note how the MS_xyz flags are the ones passed to the mount system call,
while the SB_xyz flags are what we then use in sb->s_flags.
The script to do this was:
# places to look in; re security/*: it generally should *not* be
# touched (that stuff parses mount(2) arguments directly), but
# there are two places where we really deal with superblock flags.
FILES="drivers/mtd drivers/staging/lustre fs ipc mm \
include/linux/fs.h include/uapi/linux/bfs_fs.h \
security/apparmor/apparmorfs.c security/apparmor/include/lib.h"
# the list of MS_... constants
SYMS="RDONLY NOSUID NODEV NOEXEC SYNCHRONOUS REMOUNT MANDLOCK \
DIRSYNC NOATIME NODIRATIME BIND MOVE REC VERBOSE SILENT \
POSIXACL UNBINDABLE PRIVATE SLAVE SHARED RELATIME KERNMOUNT \
I_VERSION STRICTATIME LAZYTIME SUBMOUNT NOREMOTELOCK NOSEC BORN \
ACTIVE NOUSER"
SED_PROG=
for i in $SYMS; do SED_PROG="$SED_PROG -e s/MS_$i/SB_$i/g"; done
# we want files that contain at least one of MS_...,
# with fs/namespace.c and fs/pnode.c excluded.
L=$(for i in $SYMS; do git grep -w -l MS_$i $FILES; done| sort|uniq|grep -v '^fs/namespace.c'|grep -v '^fs/pnode.c')
for f in $L; do sed -i $f $SED_PROG; done
Requested-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull compat and uaccess updates from Al Viro:
- {get,put}_compat_sigset() series
- assorted compat ioctl stuff
- more set_fs() elimination
- a few more timespec64 conversions
- several removals of pointless access_ok() in places where it was
followed only by non-__ variants of primitives
* 'misc.compat' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (24 commits)
coredump: call do_unlinkat directly instead of sys_unlink
fs: expose do_unlinkat for built-in callers
ext4: take handling of EXT4_IOC_GROUP_ADD into a helper, get rid of set_fs()
ipmi: get rid of pointless access_ok()
pi433: sanitize ioctl
cxlflash: get rid of pointless access_ok()
mtdchar: get rid of pointless access_ok()
r128: switch compat ioctls to drm_ioctl_kernel()
selection: get rid of field-by-field copyin
VT_RESIZEX: get rid of field-by-field copyin
i2c compat ioctls: move to ->compat_ioctl()
sched_rr_get_interval(): move compat to native, get rid of set_fs()
mips: switch to {get,put}_compat_sigset()
sparc: switch to {get,put}_compat_sigset()
s390: switch to {get,put}_compat_sigset()
ppc: switch to {get,put}_compat_sigset()
parisc: switch to {get,put}_compat_sigset()
get_compat_sigset()
get rid of {get,put}_compat_itimerspec()
io_getevents: Use timespec64 to represent timeouts
...
* Introduce MAP_SYNC and MAP_SHARED_VALIDATE, a mechanism to enable
'userspace flush' of persistent memory updates via filesystem-dax
mappings. It arranges for any filesystem metadata updates that may be
required to satisfy a write fault to also be flushed ("on disk") before
the kernel returns to userspace from the fault handler. Effectively
every write-fault that dirties metadata completes an fsync() before
returning from the fault handler. The new MAP_SHARED_VALIDATE mapping
type guarantees that the MAP_SYNC flag is validated as supported by the
filesystem's ->mmap() file operation.
* Add support for the standard ACPI 6.2 label access methods that
replace the NVDIMM_FAMILY_INTEL (vendor specific) label methods. This
enables interoperability with environments that only implement the
standardized methods.
* Add support for the ACPI 6.2 NVDIMM media error injection methods.
* Add support for the NVDIMM_FAMILY_INTEL v1.6 DIMM commands for latch
last shutdown status, firmware update, SMART error injection, and
SMART alarm threshold control.
* Cleanup physical address information disclosures to be root-only.
* Fix revalidation of the DIMM "locked label area" status to support
dynamic unlock of the label area.
* Expand unit test infrastructure to mock the ACPI 6.2 Translate SPA
(system-physical-address) command and error injection commands.
Acknowledgements that came after the commits were pushed to -next:
957ac8c421 dax: fix PMD faults on zero-length files
Reviewed-by: Ross Zwisler <ross.zwisler@linux.intel.com>
a39e596baa xfs: support for synchronous DAX faults
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
7b565c9f96 xfs: Implement xfs_filemap_pfn_mkwrite() using __xfs_filemap_fault()
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
-----BEGIN PGP SIGNATURE-----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=h2vZ
-----END PGP SIGNATURE-----
Merge tag 'libnvdimm-for-4.15' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm
Pull libnvdimm and dax updates from Dan Williams:
"Save for a few late fixes, all of these commits have shipped in -next
releases since before the merge window opened, and 0day has given a
build success notification.
The ext4 touches came from Jan, and the xfs touches have Darrick's
reviewed-by. An xfstest for the MAP_SYNC feature has been through
a few round of reviews and is on track to be merged.
- Introduce MAP_SYNC and MAP_SHARED_VALIDATE, a mechanism to enable
'userspace flush' of persistent memory updates via filesystem-dax
mappings. It arranges for any filesystem metadata updates that may
be required to satisfy a write fault to also be flushed ("on disk")
before the kernel returns to userspace from the fault handler.
Effectively every write-fault that dirties metadata completes an
fsync() before returning from the fault handler. The new
MAP_SHARED_VALIDATE mapping type guarantees that the MAP_SYNC flag
is validated as supported by the filesystem's ->mmap() file
operation.
- Add support for the standard ACPI 6.2 label access methods that
replace the NVDIMM_FAMILY_INTEL (vendor specific) label methods.
This enables interoperability with environments that only implement
the standardized methods.
- Add support for the ACPI 6.2 NVDIMM media error injection methods.
- Add support for the NVDIMM_FAMILY_INTEL v1.6 DIMM commands for
latch last shutdown status, firmware update, SMART error injection,
and SMART alarm threshold control.
- Cleanup physical address information disclosures to be root-only.
- Fix revalidation of the DIMM "locked label area" status to support
dynamic unlock of the label area.
- Expand unit test infrastructure to mock the ACPI 6.2 Translate SPA
(system-physical-address) command and error injection commands.
Acknowledgements that came after the commits were pushed to -next:
- 957ac8c421 ("dax: fix PMD faults on zero-length files"):
Reviewed-by: Ross Zwisler <ross.zwisler@linux.intel.com>
- a39e596baa ("xfs: support for synchronous DAX faults") and
7b565c9f96 ("xfs: Implement xfs_filemap_pfn_mkwrite() using __xfs_filemap_fault()")
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>"
* tag 'libnvdimm-for-4.15' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm: (49 commits)
acpi, nfit: add 'Enable Latch System Shutdown Status' command support
dax: fix general protection fault in dax_alloc_inode
dax: fix PMD faults on zero-length files
dax: stop requiring a live device for dax_flush()
brd: remove dax support
dax: quiet bdev_dax_supported()
fs, dax: unify IOMAP_F_DIRTY read vs write handling policy in the dax core
tools/testing/nvdimm: unit test clear-error commands
acpi, nfit: validate commands against the device type
tools/testing/nvdimm: stricter bounds checking for error injection commands
xfs: support for synchronous DAX faults
xfs: Implement xfs_filemap_pfn_mkwrite() using __xfs_filemap_fault()
ext4: Support for synchronous DAX faults
ext4: Simplify error handling in ext4_dax_huge_fault()
dax: Implement dax_finish_sync_fault()
dax, iomap: Add support for synchronous faults
mm: Define MAP_SYNC and VM_SYNC flags
dax: Allow tuning whether dax_insert_mapping_entry() dirties entry
dax: Allow dax_iomap_fault() to return pfn
dax: Fix comment describing dax_iomap_fault()
...
Every pagevec_init user claims the pages being released are hot even in
cases where it is unlikely the pages are hot. As no one cares about the
hotness of pages being released to the allocator, just ditch the
parameter.
No performance impact is expected as the overhead is marginal. The
parameter is removed simply because it is a bit stupid to have a useless
parameter copied everywhere.
Link: http://lkml.kernel.org/r/20171018075952.10627-6-mgorman@techsingularity.net
Signed-off-by: Mel Gorman <mgorman@techsingularity.net>
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Dave Chinner <david@fromorbit.com>
Cc: Dave Hansen <dave.hansen@intel.com>
Cc: Jan Kara <jack@suse.cz>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
All users of pagevec_lookup() and pagevec_lookup_range() now pass
PAGEVEC_SIZE as a desired number of pages. Just drop the argument.
Link: http://lkml.kernel.org/r/20171009151359.31984-15-jack@suse.cz
Signed-off-by: Jan Kara <jack@suse.cz>
Reviewed-by: Daniel Jordan <daniel.m.jordan@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We want only pages from given range in ext4_writepages(). Use
pagevec_lookup_range_tag() instead of pagevec_lookup_tag() and remove
unnecessary code.
Link: http://lkml.kernel.org/r/20171009151359.31984-5-jack@suse.cz
Signed-off-by: Jan Kara <jack@suse.cz>
Reviewed-by: Daniel Jordan <daniel.m.jordan@oracle.com>
Cc: "Theodore Ts'o" <tytso@mit.edu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
two data corruption bugs involving DAX, as well as a corruption bug
after a crash during a racing fallocate and delayed allocation.
Finally, a number of cleanups and optimizations.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEK2m5VNv+CHkogTfJ8vlZVpUNgaMFAloJCiEACgkQ8vlZVpUN
gaOahAgAhcgdPagn/B5w+6vKFdH+hOJLKyGI0adGDyWD9YBXN0wFQvliVgXrTKei
hxW2GdQGc6yHv9mOjvD+4Fn2AnTZk8F3GtG6zdqRM08JGF/IN2Jax2boczG/XnUz
rT9cd3ic2Ff0KaUX+Yos55QwomTh5CAeRPgvB69o9D6L4VJzTlsWKSOBR19FmrSG
NDmzZibgWmHcqzW9Bq8ZrXXx+KB42kUlc8tYYm2n6MTaE0LMvp3d9XcFcnm/I7Bk
MGa2d3/3FArGD6Rkl/E82MXMSElOHJnY6jGYSDaadUeMI5FXkA6tECOSJYXqShdb
ZJwkOBwfv2lbYZJxIBJTy/iA6zdsoQ==
=ZzaJ
-----END PGP SIGNATURE-----
Merge tag 'ext4_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4
Pull ext4 updates from Ted Ts'o:
- Add support for online resizing of file systems with bigalloc
- Fix a two data corruption bugs involving DAX, as well as a corruption
bug after a crash during a racing fallocate and delayed allocation.
- Finally, a number of cleanups and optimizations.
* tag 'ext4_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4:
ext4: improve smp scalability for inode generation
ext4: add support for online resizing with bigalloc
ext4: mention noload when recovering on read-only device
Documentation: fix little inconsistencies
ext4: convert timers to use timer_setup()
jbd2: convert timers to use timer_setup()
ext4: remove duplicate extended attributes defs
ext4: add ext4_should_use_dax()
ext4: add sanity check for encryption + DAX
ext4: prevent data corruption with journaling + DAX
ext4: prevent data corruption with inline data + DAX
ext4: fix interaction between i_size, fallocate, and delalloc after a crash
ext4: retry allocations conservatively
ext4: Switch to iomap for SEEK_HOLE / SEEK_DATA
ext4: Add iomap support for inline data
iomap: Add IOMAP_F_DATA_INLINE flag
iomap: Switch from blkno to disk offset
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEK2m5VNv+CHkogTfJ8vlZVpUNgaMFAloI8AUACgkQ8vlZVpUN
gaMdjgf8CCW7UhPjoZYwF8sUNtAaX9+JZT1maOcXUhpJ3vRQiRn+AzRH6yBYMm79
+NZBwVlk4dlEe55Wh4yFIStMAstqzCrke4C9CSbExjgHNsJdU4znyYuLRMbLfyO0
6c4NObiAIKJdW1/te1aN90keGC6min8pBZot+FqZsRr+Kq2+IOtM43JAv7efOLev
v3LCjUf9JKxatoB8tgw4AJRa1p18p7D2APWTG05VlFq63TjhVIYNvvwcQlizLwGY
cuEq3X59FbFdX06fJnucujU3WP3ES4/3rhufBK4NNaec5e5dbnH2KlAx7J5SyMIZ
0qUFB/dmXDSb3gsfScSGo1F71Ad0CA==
=asAm
-----END PGP SIGNATURE-----
Merge tag 'fscrypt-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/fscrypt
Pull fscrypt updates from Ted Ts'o:
"Lots of cleanups, mostly courtesy by Eric Biggers"
* tag 'fscrypt-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/fscrypt:
fscrypt: lock mutex before checking for bounce page pool
fscrypt: add a documentation file for filesystem-level encryption
ext4: switch to fscrypt_prepare_setattr()
ext4: switch to fscrypt_prepare_lookup()
ext4: switch to fscrypt_prepare_rename()
ext4: switch to fscrypt_prepare_link()
ext4: switch to fscrypt_file_open()
fscrypt: new helper function - fscrypt_prepare_setattr()
fscrypt: new helper function - fscrypt_prepare_lookup()
fscrypt: new helper function - fscrypt_prepare_rename()
fscrypt: new helper function - fscrypt_prepare_link()
fscrypt: new helper function - fscrypt_file_open()
fscrypt: new helper function - fscrypt_require_key()
fscrypt: remove unneeded empty fscrypt_operations structs
fscrypt: remove ->is_encrypted()
fscrypt: switch from ->is_encrypted() to IS_ENCRYPTED()
fs, fscrypt: add an S_ENCRYPTED inode flag
fscrypt: clean up include file mess
While reviewing whether MAP_SYNC should strengthen its current guarantee
of syncing writes from the initiating process to also include
third-party readers observing dirty metadata, Dave pointed out that the
check of IOMAP_WRITE is misplaced.
The policy of what to with IOMAP_F_DIRTY should be separated from the
generic filesystem mechanism of reporting dirty metadata. Move this
policy to the fs-dax core to simplify the per-filesystem iomap handlers,
and further centralize code that implements the MAP_SYNC policy. This
otherwise should not change behavior, it just makes it easier to change
behavior in the future.
Reviewed-by: Jan Kara <jack@suse.cz>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Cc: Ross Zwisler <ross.zwisler@linux.intel.com>
Reported-by: Dave Chinner <david@fromorbit.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
->s_next_generation is protected by s_next_gen_lock but its usage
pattern is very primitive. We don't actually need sequentially
increasing new generation numbers, so let's use prandom_u32() instead.
Reported-by: Dmitry Monakhov <dmonakhov@openvz.org>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
We return IOMAP_F_DIRTY flag from ext4_iomap_begin() when asked to
prepare blocks for writing and the inode has some uncommitted metadata
changes. In the fault handler ext4_dax_fault() we then detect this case
(through VM_FAULT_NEEDDSYNC return value) and call helper
dax_finish_sync_fault() to flush metadata changes and insert page table
entry. Note that this will also dirty corresponding radix tree entry
which is what we want - fsync(2) will still provide data integrity
guarantees for applications not using userspace flushing. And
applications using userspace flushing can avoid calling fsync(2) and
thus avoid the performance overhead.
Reviewed-by: Ross Zwisler <ross.zwisler@linux.intel.com>
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
If transaction starting fails, just bail out of the function immediately
instead of checking for that condition throughout the function.
Reviewed-by: Ross Zwisler <ross.zwisler@linux.intel.com>
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
For synchronous page fault dax_iomap_fault() will need to return PFN
which will then need to be inserted into page tables after fsync()
completes. Add necessary parameter to dax_iomap_fault().
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Ross Zwisler <ross.zwisler@linux.intel.com>
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds support for online resizing on bigalloc file system by
implementing EXT4_IOC_RESIZE_FS ioctl. Old resize interfaces (add
block groups and extend last block group) are left untouched. Tests
performed with cluster sizes of 1, 2, 4 and 8 blocks (of size 4k) per
cluster. I will add these tests to xfstests.
Signed-off-by: Harshad Shirwadkar <harshads@google.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
In the case where a filesystem has been configured without encryption
support, there is no longer any need to initialize ->s_cop at all, since
none of the methods are ever called.
Reviewed-by: Chao Yu <yuchao0@huawei.com>
Acked-by: Dave Chinner <dchinner@redhat.com>
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Now that all callers of fscrypt_operations.is_encrypted() have been
switched to IS_ENCRYPTED(), remove ->is_encrypted().
Reviewed-by: Chao Yu <yuchao0@huawei.com>
Acked-by: Dave Chinner <dchinner@redhat.com>
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Introduce a flag S_ENCRYPTED which can be set in ->i_flags to indicate
that the inode is encrypted using the fscrypt (fs/crypto/) mechanism.
Checking this flag will give the same information that
inode->i_sb->s_cop->is_encrypted(inode) currently does, but will be more
efficient. This will be useful for adding higher-level helper functions
for filesystems to use. For example we'll be able to replace this:
if (ext4_encrypted_inode(inode)) {
ret = fscrypt_get_encryption_info(inode);
if (ret)
return ret;
if (!fscrypt_has_encryption_key(inode))
return -ENOKEY;
}
with this:
ret = fscrypt_require_key(inode);
if (ret)
return ret;
... since we'll be able to retain the fast path for unencrypted files as
a single flag check, using an inline function. This wasn't possible
before because we'd have had to frequently call through the
->i_sb->s_cop->is_encrypted function pointer, even when the encryption
support was disabled or not being used.
Note: we don't define S_ENCRYPTED to 0 if CONFIG_FS_ENCRYPTION is
disabled because we want to continue to return an error if an encrypted
file is accessed without encryption support, rather than pretending that
it is unencrypted.
Reviewed-by: Chao Yu <yuchao0@huawei.com>
Acked-by: Dave Chinner <dchinner@redhat.com>
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Filesystems have to include different header files based on whether they
are compiled with encryption support or not. That's nasty and messy.
Instead, rationalise the headers so we have a single include fscrypt.h
and let it decide what internal implementation to include based on the
__FS_HAS_ENCRYPTION define. Filesystems set __FS_HAS_ENCRYPTION to 1
before including linux/fscrypt.h if they are built with encryption
support. Otherwise, they must set __FS_HAS_ENCRYPTION to 0.
Add guards to prevent fscrypt_supp.h and fscrypt_notsupp.h from being
directly included by filesystems.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
[EB: use 1 and 0 rather than defined/undefined]
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
[AV: in addition to the fix in previous commit]
Signed-off-by: Matthew Garrett <mjg59@google.com>
Cc: David Howells <dhowells@redhat.com>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Reviewed-by: David Howells <dhowells@redhat.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Help the user to find the appropriate mount option to continue mounting
the file system on a read-only device if the journal requires recovery.
Signed-off-by: Simon Ruderich <simon@ruderich.org>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly.
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Reviewed-by: Reviewed-by: Jan Kara <jack@suse.cz>
Cc: Andreas Dilger <adilger.kernel@dilger.ca>
Cc: linux-ext4@vger.kernel.org
The following commit:
commit 9b7365fc1c ("ext4: add FS_IOC_FSSETXATTR/FS_IOC_FSGETXATTR
interface support")
added several defines related to extended attributes to ext4.h. They were
added within an #ifndef FS_IOC_FSGETXATTR block with the comment:
/* Until the uapi changes get merged for project quota... */
Those uapi changes were merged by this commit:
commit 334e580a6f ("fs: XFS_IOC_FS[SG]SETXATTR to FS_IOC_FS[SG]ETXATTR
promotion")
so all the definitions needed by ext4 are available in
include/uapi/linux/fs.h. Remove the duplicates from ext4.h.
Signed-off-by: Ross Zwisler <ross.zwisler@linux.intel.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Reviewed-by: Jan Kara <jack@suse.cz>
This helper, in the spirit of ext4_should_dioread_nolock() et al., replaces
the complex conditional in ext4_set_inode_flags().
Signed-off-by: Ross Zwisler <ross.zwisler@linux.intel.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Reviewed-by: Jan Kara <jack@suse.cz>
We prevent DAX from being used on inodes which are using ext4's built in
encryption via a check in ext4_set_inode_flags(). We do have what appears
to be an unsafe transition of S_DAX in ext4_set_context(), though, where
S_DAX can get disabled without us doing a proper writeback + invalidate.
There are also issues with mm-level races when changing the value of S_DAX,
as well as issues with the VM_MIXEDMAP flag:
https://www.spinics.net/lists/linux-xfs/msg09859.html
I actually think we are safe in this case because of the following:
1) You can't encrypt an existing file. Encryption can only be set on an
empty directory, with new inodes in that directory being created with
encryption turned on, so I don't think it's possible to turn encryption on
for a file that has open DAX mmaps or outstanding I/Os.
2) There is no way to turn encryption off on a given file. Once an inode
is encrypted, it stays encrypted for the life of that inode, so we don't
have to worry about the case where we turn encryption off and S_DAX
suddenly turns on.
3) The only way we end up in ext4_set_context() to turn on encryption is
when we are creating a new file in the encrypted directory. This happens
as part of ext4_create() before the inode has been allowed to do any I/O.
Here's the call tree:
ext4_create()
__ext4_new_inode()
ext4_set_inode_flags() // sets S_DAX
fscrypt_inherit_context()
fscrypt_get_encryption_info();
ext4_set_context() // sets EXT4_INODE_ENCRYPT, clears S_DAX
So, I actually think it's safe to transition S_DAX in ext4_set_context()
without any locking, writebacks or invalidations. I've added a
WARN_ON_ONCE() sanity check to make sure that we are notified if we ever
encounter a case where we are encrypting an inode that already has data,
in which case we need to add code to safely transition S_DAX.
Signed-off-by: Ross Zwisler <ross.zwisler@linux.intel.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Reviewed-by: Jan Kara <jack@suse.cz>
The current code has the potential for data corruption when changing an
inode's journaling mode, as that can result in a subsequent unsafe change
in S_DAX.
I've captured an instance of this data corruption in the following fstest:
https://patchwork.kernel.org/patch/9948377/
Prevent this data corruption from happening by disallowing changes to the
journaling mode if the '-o dax' mount option was used. This means that for
a given filesystem we could have a mix of inodes using either DAX or
data journaling, but whatever state the inodes are in will be held for the
duration of the mount.
Signed-off-by: Ross Zwisler <ross.zwisler@linux.intel.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Reviewed-by: Jan Kara <jack@suse.cz>
Cc: stable@vger.kernel.org
If an inode has inline data it is currently prevented from using DAX by a
check in ext4_set_inode_flags(). When the inode grows inline data via
ext4_create_inline_data() or removes its inline data via
ext4_destroy_inline_data_nolock(), the value of S_DAX can change.
Currently these changes are unsafe because we don't hold off page faults
and I/O, write back dirty radix tree entries and invalidate all mappings.
There are also issues with mm-level races when changing the value of S_DAX,
as well as issues with the VM_MIXEDMAP flag:
https://www.spinics.net/lists/linux-xfs/msg09859.html
The unsafe transition of S_DAX can reliably cause data corruption, as shown
by the following fstest:
https://patchwork.kernel.org/patch/9948381/
Fix this issue by preventing the DAX mount option from being used on
filesystems that were created to support inline data. Inline data is an
option given to mkfs.ext4.
Signed-off-by: Ross Zwisler <ross.zwisler@linux.intel.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Reviewed-by: Jan Kara <jack@suse.cz>
CC: stable@vger.kernel.org
If there are pending writes subject to delayed allocation, then i_size
will show size after the writes have completed, while i_disksize
contains the value of i_size on the disk (since the writes have not
been persisted to disk).
If fallocate(2) is called with the FALLOC_FL_KEEP_SIZE flag, either
with or without the FALLOC_FL_ZERO_RANGE flag set, and the new size
after the fallocate(2) is between i_size and i_disksize, then after a
crash, if a journal commit has resulted in the changes made by the
fallocate() call to be persisted after a crash, but the delayed
allocation write has not resolved itself, i_size would not be updated,
and this would cause the following e2fsck complaint:
Inode 12, end of extent exceeds allowed value
(logical block 33, physical block 33441, len 7)
This can only take place on a sparse file, where the fallocate(2) call
is allocating blocks in a range which is before a pending delayed
allocation write which is extending i_size. Since this situation is
quite rare, and the window in which the crash must take place is
typically < 30 seconds, in practice this condition will rarely happen.
Nevertheless, it can be triggered in testing, and in particular by
xfstests generic/456.
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Reported-by: Amir Goldstein <amir73il@gmail.com>
Cc: stable@vger.kernel.org
Now that we no longer try to reserve metadata blocks for delayed
allocations (which tended to overestimate the required number of
blocks significantly), we really don't need retry allocations when the
disk is very full as aggressively any more.
The only time when it makes sense to retry an allocation is if we have
freshly deleted blocks that will only become available after a
transaction commit. And if we lose that race, it's not worth it to
try more than once.
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Switch to the iomap_seek_hole and iomap_seek_data helpers for
implementing lseek SEEK_HOLE / SEEK_DATA, and remove all the code that
isn't needed any more.
Note that with this patch ext4 will now always depend on the iomap code
instead of only when CONFIG_DAX is enabled, and it requires adding a
call into the extent status tree for iomap_begin as well to properly
deal with delalloc extents.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Reviewed-by: Jan Kara <jack@suse.cz>
[More fixes and cleanups by Andreas]
Report inline data as a IOMAP_F_DATA_INLINE mapping. This allows to use
iomap_seek_hole and iomap_seek_data in ext4_llseek and makes switching
to iomap_fiemap in ext4_fiemap easier.
Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Reviewed-by: Jan Kara <jack@suse.cz>
Replace iomap->blkno, the sector number, with iomap->addr, the disk
offset in bytes. For invalid disk offsets, use the special value
IOMAP_NULL_ADDR instead of IOMAP_NULL_BLOCK.
This allows to use iomap for mappings which are not block aligned, such
as inline data on ext4.
Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com> # iomap, xfs
Reviewed-by: Jan Kara <jack@suse.cz>
Pull nowait read support from Al Viro:
"Support IOCB_NOWAIT for buffered reads and block devices"
* 'work.read_write' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
block_dev: support RFW_NOWAIT on block device nodes
fs: support RWF_NOWAIT for buffered reads
fs: support IOCB_NOWAIT in generic_file_buffered_read
fs: pass iocb to do_generic_file_read
Pull mount flag updates from Al Viro:
"Another chunk of fmount preparations from dhowells; only trivial
conflicts for that part. It separates MS_... bits (very grotty
mount(2) ABI) from the struct super_block ->s_flags (kernel-internal,
only a small subset of MS_... stuff).
This does *not* convert the filesystems to new constants; only the
infrastructure is done here. The next step in that series is where the
conflicts would be; that's the conversion of filesystems. It's purely
mechanical and it's better done after the merge, so if you could run
something like
list=$(for i in MS_RDONLY MS_NOSUID MS_NODEV MS_NOEXEC MS_SYNCHRONOUS MS_MANDLOCK MS_DIRSYNC MS_NOATIME MS_NODIRATIME MS_SILENT MS_POSIXACL MS_KERNMOUNT MS_I_VERSION MS_LAZYTIME; do git grep -l $i fs drivers/staging/lustre drivers/mtd ipc mm include/linux; done|sort|uniq|grep -v '^fs/namespace.c$')
sed -i -e 's/\<MS_RDONLY\>/SB_RDONLY/g' \
-e 's/\<MS_NOSUID\>/SB_NOSUID/g' \
-e 's/\<MS_NODEV\>/SB_NODEV/g' \
-e 's/\<MS_NOEXEC\>/SB_NOEXEC/g' \
-e 's/\<MS_SYNCHRONOUS\>/SB_SYNCHRONOUS/g' \
-e 's/\<MS_MANDLOCK\>/SB_MANDLOCK/g' \
-e 's/\<MS_DIRSYNC\>/SB_DIRSYNC/g' \
-e 's/\<MS_NOATIME\>/SB_NOATIME/g' \
-e 's/\<MS_NODIRATIME\>/SB_NODIRATIME/g' \
-e 's/\<MS_SILENT\>/SB_SILENT/g' \
-e 's/\<MS_POSIXACL\>/SB_POSIXACL/g' \
-e 's/\<MS_KERNMOUNT\>/SB_KERNMOUNT/g' \
-e 's/\<MS_I_VERSION\>/SB_I_VERSION/g' \
-e 's/\<MS_LAZYTIME\>/SB_LAZYTIME/g' \
$list
and commit it with something along the lines of 'convert filesystems
away from use of MS_... constants' as commit message, it would save a
quite a bit of headache next cycle"
* 'work.mount' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
VFS: Differentiate mount flags (MS_*) from internal superblock flags
VFS: Convert sb->s_flags & MS_RDONLY to sb_rdonly(sb)
vfs: Add sb_rdonly(sb) to query the MS_RDONLY flag on s_flags
* Media error handling support in the Block Translation Table (BTT)
driver is reworked to address sleeping-while-atomic locking and
memory-allocation-context conflicts.
* The dax_device lookup overhead for xfs and ext4 is moved out of the
iomap hot-path to a mount-time lookup.
* A new 'ecc_unit_size' sysfs attribute is added to advertise the
read-modify-write boundary property of a persistent memory range.
* Preparatory fix-ups for arm and powerpc pmem support are included
along with other miscellaneous fixes.
-----BEGIN PGP SIGNATURE-----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=5iGY
-----END PGP SIGNATURE-----
Merge tag 'libnvdimm-for-4.14' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm
Pull libnvdimm from Dan Williams:
"A rework of media error handling in the BTT driver and other updates.
It has appeared in a few -next releases and collected some late-
breaking build-error and warning fixups as a result.
Summary:
- Media error handling support in the Block Translation Table (BTT)
driver is reworked to address sleeping-while-atomic locking and
memory-allocation-context conflicts.
- The dax_device lookup overhead for xfs and ext4 is moved out of the
iomap hot-path to a mount-time lookup.
- A new 'ecc_unit_size' sysfs attribute is added to advertise the
read-modify-write boundary property of a persistent memory range.
- Preparatory fix-ups for arm and powerpc pmem support are included
along with other miscellaneous fixes"
* tag 'libnvdimm-for-4.14' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm: (26 commits)
libnvdimm, btt: fix format string warnings
libnvdimm, btt: clean up warning and error messages
ext4: fix null pointer dereference on sbi
libnvdimm, nfit: move the check on nd_reserved2 to the endpoint
dax: fix FS_DAX=n BLOCK=y compilation
libnvdimm: fix integer overflow static analysis warning
libnvdimm, nd_blk: remove mmio_flush_range()
libnvdimm, btt: rework error clearing
libnvdimm: fix potential deadlock while clearing errors
libnvdimm, btt: cache sector_size in arena_info
libnvdimm, btt: ensure that flags were also unchanged during a map_read
libnvdimm, btt: refactor map entry operations with macros
libnvdimm, btt: fix a missed NVDIMM_IO_ATOMIC case in the write path
libnvdimm, nfit: export an 'ecc_unit_size' sysfs attribute
ext4: perform dax_device lookup at mount
ext2: perform dax_device lookup at mount
xfs: perform dax_device lookup at mount
dax: introduce a fs_dax_get_by_bdev() helper
libnvdimm, btt: check memory allocation failure
libnvdimm, label: fix index block size calculation
...
Pull quota scaling updates from Jan Kara:
"This contains changes to make the quota subsystem more scalable.
Reportedly it improves number of files created per second on ext4
filesystem on fast storage by about a factor of 2x"
* 'quota_scaling' of git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-fs: (28 commits)
quota: Add lock annotations to struct members
quota: Reduce contention on dq_data_lock
fs: Provide __inode_get_bytes()
quota: Inline dquot_[re]claim_reserved_space() into callsite
quota: Inline inode_{incr,decr}_space() into callsites
quota: Inline functions into their callsites
ext4: Disable dirty list tracking of dquots when journalling quotas
quota: Allow disabling tracking of dirty dquots in a list
quota: Remove dq_wait_unused from dquot
quota: Move locking into clear_dquot_dirty()
quota: Do not dirty bad dquots
quota: Fix possible corruption of dqi_flags
quota: Propagate ->quota_read errors from v2_read_file_info()
quota: Fix error codes in v2_read_file_info()
quota: Push dqio_sem down to ->read_file_info()
quota: Push dqio_sem down to ->write_file_info()
quota: Push dqio_sem down to ->get_next_id()
quota: Push dqio_sem down to ->release_dqblk()
quota: Remove locking for writing to the old quota format
quota: Do not acquire dqio_sem for dquot overwrites in v2 format
...
Pull block layer updates from Jens Axboe:
"This is the first pull request for 4.14, containing most of the code
changes. It's a quiet series this round, which I think we needed after
the churn of the last few series. This contains:
- Fix for a registration race in loop, from Anton Volkov.
- Overflow complaint fix from Arnd for DAC960.
- Series of drbd changes from the usual suspects.
- Conversion of the stec/skd driver to blk-mq. From Bart.
- A few BFQ improvements/fixes from Paolo.
- CFQ improvement from Ritesh, allowing idling for group idle.
- A few fixes found by Dan's smatch, courtesy of Dan.
- A warning fixup for a race between changing the IO scheduler and
device remova. From David Jeffery.
- A few nbd fixes from Josef.
- Support for cgroup info in blktrace, from Shaohua.
- Also from Shaohua, new features in the null_blk driver to allow it
to actually hold data, among other things.
- Various corner cases and error handling fixes from Weiping Zhang.
- Improvements to the IO stats tracking for blk-mq from me. Can
drastically improve performance for fast devices and/or big
machines.
- Series from Christoph removing bi_bdev as being needed for IO
submission, in preparation for nvme multipathing code.
- Series from Bart, including various cleanups and fixes for switch
fall through case complaints"
* 'for-4.14/block' of git://git.kernel.dk/linux-block: (162 commits)
kernfs: checking for IS_ERR() instead of NULL
drbd: remove BIOSET_NEED_RESCUER flag from drbd_{md_,}io_bio_set
drbd: Fix allyesconfig build, fix recent commit
drbd: switch from kmalloc() to kmalloc_array()
drbd: abort drbd_start_resync if there is no connection
drbd: move global variables to drbd namespace and make some static
drbd: rename "usermode_helper" to "drbd_usermode_helper"
drbd: fix race between handshake and admin disconnect/down
drbd: fix potential deadlock when trying to detach during handshake
drbd: A single dot should be put into a sequence.
drbd: fix rmmod cleanup, remove _all_ debugfs entries
drbd: Use setup_timer() instead of init_timer() to simplify the code.
drbd: fix potential get_ldev/put_ldev refcount imbalance during attach
drbd: new disk-option disable-write-same
drbd: Fix resource role for newly created resources in events2
drbd: mark symbols static where possible
drbd: Send P_NEG_ACK upon write error in protocol != C
drbd: add explicit plugging when submitting batches
drbd: change list_for_each_safe to while(list_first_entry_or_null)
drbd: introduce drbd_recv_header_maybe_unplug
...
Merge updates from Andrew Morton:
- various misc bits
- DAX updates
- OCFS2
- most of MM
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (119 commits)
mm,fork: introduce MADV_WIPEONFORK
x86,mpx: make mpx depend on x86-64 to free up VMA flag
mm: add /proc/pid/smaps_rollup
mm: hugetlb: clear target sub-page last when clearing huge page
mm: oom: let oom_reap_task and exit_mmap run concurrently
swap: choose swap device according to numa node
mm: replace TIF_MEMDIE checks by tsk_is_oom_victim
mm, oom: do not rely on TIF_MEMDIE for memory reserves access
z3fold: use per-cpu unbuddied lists
mm, swap: don't use VMA based swap readahead if HDD is used as swap
mm, swap: add sysfs interface for VMA based swap readahead
mm, swap: VMA based swap readahead
mm, swap: fix swap readahead marking
mm, swap: add swap readahead hit statistics
mm/vmalloc.c: don't reinvent the wheel but use existing llist API
mm/vmstat.c: fix wrong comment
selftests/memfd: add memfd_create hugetlbfs selftest
mm/shmem: add hugetlbfs support to memfd_create()
mm, devm_memremap_pages: use multi-order radix for ZONE_DEVICE lookups
mm/vmalloc.c: halve the number of comparisons performed in pcpu_get_vm_areas()
...
All users of pagevec_lookup() and pagevec_lookup_range() now pass
PAGEVEC_SIZE as a desired number of pages.
Just drop the argument.
Link: http://lkml.kernel.org/r/20170726114704.7626-11-jack@suse.cz
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Both occurences of pagevec_lookup() actually want only pages from a
given range. Use pagevec_lookup_range() for the lookup.
Link: http://lkml.kernel.org/r/20170726114704.7626-7-jack@suse.cz
Signed-off-by: Jan Kara <jack@suse.cz>
Cc: "Theodore Ts'o" <tytso@mit.edu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use pagevec_lookup_range() in ext4_find_unwritten_pgoff() since we are
interested only in pages in the given range. Simplify the logic as a
result of not getting pages out of range and index getting automatically
advanced.
Link: http://lkml.kernel.org/r/20170726114704.7626-6-jack@suse.cz
Signed-off-by: Jan Kara <jack@suse.cz>
Cc: "Theodore Ts'o" <tytso@mit.edu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Make pagevec_lookup() (and underlying find_get_pages()) update index to
the next page where iteration should continue. Most callers want this
and also pagevec_lookup_tag() already does this.
Link: http://lkml.kernel.org/r/20170726114704.7626-3-jack@suse.cz
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When servicing mmap() reads from file holes the current DAX code
allocates a page cache page of all zeroes and places the struct page
pointer in the mapping->page_tree radix tree.
This has three major drawbacks:
1) It consumes memory unnecessarily. For every 4k page that is read via
a DAX mmap() over a hole, we allocate a new page cache page. This
means that if you read 1GiB worth of pages, you end up using 1GiB of
zeroed memory. This is easily visible by looking at the overall
memory consumption of the system or by looking at /proc/[pid]/smaps:
7f62e72b3000-7f63272b3000 rw-s 00000000 103:00 12 /root/dax/data
Size: 1048576 kB
Rss: 1048576 kB
Pss: 1048576 kB
Shared_Clean: 0 kB
Shared_Dirty: 0 kB
Private_Clean: 1048576 kB
Private_Dirty: 0 kB
Referenced: 1048576 kB
Anonymous: 0 kB
LazyFree: 0 kB
AnonHugePages: 0 kB
ShmemPmdMapped: 0 kB
Shared_Hugetlb: 0 kB
Private_Hugetlb: 0 kB
Swap: 0 kB
SwapPss: 0 kB
KernelPageSize: 4 kB
MMUPageSize: 4 kB
Locked: 0 kB
2) It is slower than using a common zero page because each page fault
has more work to do. Instead of just inserting a common zero page we
have to allocate a page cache page, zero it, and then insert it. Here
are the average latencies of dax_load_hole() as measured by ftrace on
a random test box:
Old method, using zeroed page cache pages: 3.4 us
New method, using the common 4k zero page: 0.8 us
This was the average latency over 1 GiB of sequential reads done by
this simple fio script:
[global]
size=1G
filename=/root/dax/data
fallocate=none
[io]
rw=read
ioengine=mmap
3) The fact that we had to check for both DAX exceptional entries and
for page cache pages in the radix tree made the DAX code more
complex.
Solve these issues by following the lead of the DAX PMD code and using a
common 4k zero page instead. As with the PMD code we will now insert a
DAX exceptional entry into the radix tree instead of a struct page
pointer which allows us to remove all the special casing in the DAX
code.
Note that we do still pretty aggressively check for regular pages in the
DAX radix tree, especially where we take action based on the bits set in
the page. If we ever find a regular page in our radix tree now that
most likely means that someone besides DAX is inserting pages (which has
happened lots of times in the past), and we want to find that out early
and fail loudly.
This solution also removes the extra memory consumption. Here is that
same /proc/[pid]/smaps after 1GiB of reading from a hole with the new
code:
7f2054a74000-7f2094a74000 rw-s 00000000 103:00 12 /root/dax/data
Size: 1048576 kB
Rss: 0 kB
Pss: 0 kB
Shared_Clean: 0 kB
Shared_Dirty: 0 kB
Private_Clean: 0 kB
Private_Dirty: 0 kB
Referenced: 0 kB
Anonymous: 0 kB
LazyFree: 0 kB
AnonHugePages: 0 kB
ShmemPmdMapped: 0 kB
Shared_Hugetlb: 0 kB
Private_Hugetlb: 0 kB
Swap: 0 kB
SwapPss: 0 kB
KernelPageSize: 4 kB
MMUPageSize: 4 kB
Locked: 0 kB
Overall system memory consumption is similarly improved.
Another major change is that we remove dax_pfn_mkwrite() from our fault
flow, and instead rely on the page fault itself to make the PTE dirty
and writeable. The following description from the patch adding the
vm_insert_mixed_mkwrite() call explains this a little more:
"To be able to use the common 4k zero page in DAX we need to have our
PTE fault path look more like our PMD fault path where a PTE entry
can be marked as dirty and writeable as it is first inserted rather
than waiting for a follow-up dax_pfn_mkwrite() =>
finish_mkwrite_fault() call.
Right now we can rely on having a dax_pfn_mkwrite() call because we
can distinguish between these two cases in do_wp_page():
case 1: 4k zero page => writable DAX storage
case 2: read-only DAX storage => writeable DAX storage
This distinction is made by via vm_normal_page(). vm_normal_page()
returns false for the common 4k zero page, though, just as it does
for DAX ptes. Instead of special casing the DAX + 4k zero page case
we will simplify our DAX PTE page fault sequence so that it matches
our DAX PMD sequence, and get rid of the dax_pfn_mkwrite() helper.
We will instead use dax_iomap_fault() to handle write-protection
faults.
This means that insert_pfn() needs to follow the lead of
insert_pfn_pmd() and allow us to pass in a 'mkwrite' flag. If
'mkwrite' is set insert_pfn() will do the work that was previously
done by wp_page_reuse() as part of the dax_pfn_mkwrite() call path"
Link: http://lkml.kernel.org/r/20170724170616.25810-4-ross.zwisler@linux.intel.com
Signed-off-by: Ross Zwisler <ross.zwisler@linux.intel.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Cc: "Darrick J. Wong" <darrick.wong@oracle.com>
Cc: "Theodore Ts'o" <tytso@mit.edu>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: Andreas Dilger <adilger.kernel@dilger.ca>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Dave Chinner <david@fromorbit.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Matthew Wilcox <mawilcox@microsoft.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In the case of a kzalloc failure when allocating sbi we end up
with a null pointer dereference on sbi when assigning sbi->s_daxdev.
Fix this by moving the assignment of sbi->s_daxdev to after the
null pointer check of sbi.
Detected by CoverityScan CID#1455379 ("Dereference before null check")
Fixes: 5e405595e5 ("ext4: perform dax_device lookup at mount")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
This is based on the old idea and code from Milosz Tanski. With the aio
nowait code it becomes mostly trivial now. Buffered writes continue to
return -EOPNOTSUPP if RWF_NOWAIT is passed.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Jan Kara <jack@suse.cz>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
The ->iomap_begin() operation is a hot path, so cache the
fs_dax_get_by_host() result at mount time to avoid the incurring the
hash lookup overhead on a per-i/o basis.
Cc: "Theodore Ts'o" <tytso@mit.edu>
Cc: Andreas Dilger <adilger.kernel@dilger.ca>
Reviewed-by: Jan Kara <jack@suse.cz>
Reported-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Avoid a 32-bit time overflow in recently_deleted() since i_dtime
(inode deletion time) is stored only as a 32-bit value on disk.
Since i_dtime isn't used for much beyond a boolean value in e2fsck
and is otherwise only used in this function in the kernel, there is
no benefit to use more space in the inode for this field on disk.
Instead, compare only the relative deletion time with the low
32 bits of the time using the newly-added time_before32() helper,
which is similar to time_before() and time_after() for jiffies.
Increase RECENTCY_DIRTY to 300s based on Ted's comments about
usage experience at Google.
Signed-off-by: Andreas Dilger <adilger@dilger.ca>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
If an ext4 filesystem is mounted with both the DAX and read-only
options, executables on that filesystem will fail to start (claiming
'Segmentation fault') due to the fault handler returning
VM_FAULT_SIGBUS.
This is due to the DAX fault handler (see ext4_dax_huge_fault)
attempting to write to the journal when FAULT_FLAG_WRITE is set. This is
the wrong behavior for write faults which will lead to a COW page; in
particular, this fails for readonly mounts.
This change avoids journal writes for faults that are expected to COW.
It might be the case that this could be better handled in
ext4_iomap_begin / ext4_iomap_end (called via iomap_ops inside
dax_iomap_fault). These is some overlap already (e.g. grabbing journal
handles).
Signed-off-by: Randy Dodgen <dodgen@google.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Reviewed-by: Jan Kara <jack@suse.cz>
Reviewed-by: Ross Zwisler <ross.zwisler@linux.intel.com>
Quota does not get enabled for read-only mounts if filesystem
has quota feature, so that quotas cannot updated during orphan
cleanup, which will lead to quota inconsistency.
This patch turn on quotas during orphan cleanup for this case,
make sure quotas can be updated correctly.
Reported-by: Jan Kara <jack@suse.cz>
Signed-off-by: zhangyi (F) <yi.zhang@huawei.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Reviewed-by: Jan Kara <jack@suse.cz>
Cc: stable@vger.kernel.org # 3.18+
Current ext4 quota should always "usage enabled" if the
quota feautre is enabled. But in ext4_orphan_cleanup(), it
turn quotas off directly (used for the older journaled
quota), so we cannot turn it on again via "quotaon" unless
umount and remount ext4.
Simple reproduce:
mkfs.ext4 -O project,quota /dev/vdb1
mount -o prjquota /dev/vdb1 /mnt
chattr -p 123 /mnt
chattr +P /mnt
touch /mnt/aa /mnt/bb
exec 100<>/mnt/aa
rm -f /mnt/aa
sync
echo c > /proc/sysrq-trigger
#reboot and mount
mount -o prjquota /dev/vdb1 /mnt
#query status
quotaon -Ppv /dev/vdb1
#output
quotaon: Cannot find mountpoint for device /dev/vdb1
quotaon: No correct mountpoint specified.
This patch add check for journaled quotas to avoid incorrect
quotaoff when ext4 has quota feautre.
Signed-off-by: zhangyi (F) <yi.zhang@huawei.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Reviewed-by: Jan Kara <jack@suse.cz>
Cc: stable@vger.kernel.org # 3.18
On transformation of str to hash, computed value is initialised before
first byte modulo 4. But it is already initialised before entering loop
and after processing last byte modulo 4. So the corresponding test and
initialisation could be removed.
Signed-off-by: Damien Guibouret <damien.guibouret@partition-saving.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Original Lustre ea_inode feature did not have ref counts on xattr inodes
because there was always one parent that referenced it. New
implementation expects ref count to be initialized which is not true for
Lustre case. Handle this by detecting Lustre created xattr inode and set
its ref count to 1.
The quota handling of xattr inodes have also changed with deduplication
support. New implementation manually manages quotas to support sharing
across multiple users. A consequence is that, a referencing inode
incorporates the blocks of xattr inode into its own i_block field.
We need to know how a xattr inode was created so that we can reverse the
block charges during reference removal. This is handled by introducing a
EXT4_STATE_LUSTRE_EA_INODE flag. The flag is set on a xattr inode if
inode appears to have been created by Lustre. During xattr inode reference
removal, the manual quota uncharge is skipped if the flag is set.
Signed-off-by: Tahsin Erdogan <tahsin@google.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Changing behavior based on the version code is a timebomb waiting to
happen, and not easily bisectable. Drop it and leave any removal
to explicit developer action. (And I don't think file system
should _ever_ remove backwards compatibility that has no explicit
flag, but I'll leave that to the ext4 folks).
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Reviewed-by: Eric Biggers <ebiggers@google.com>
Replace the specification of data structures by pointer dereferences
as the parameter for the operator "sizeof" to make the corresponding size
determination a bit safer according to the Linux coding style convention.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Reviewed-by: Eric Sandeen <sandeen@redhat.com>
In the ext4 implementations of SEEK_HOLE and SEEK_DATA, make sure we
return -ENXIO for negative offsets instead of banging around inside
the extent code and returning -EFSCORRUPTED.
Reported-by: Mateusz S <muttdini@gmail.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Cc: stable@vger.kernel.org # 4.6
While running number of creating file threads concurrently,
we found heavy lock contention on group spinlock:
FUNC TOTAL_TIME(us) COUNT AVG(us)
ext4_create 1707443399 1440000 1185.72
_raw_spin_lock 1317641501 180899929 7.28
jbd2__journal_start 287821030 1453950 197.96
jbd2_journal_get_write_access 33441470 73077185 0.46
ext4_add_nondir 29435963 1440000 20.44
ext4_add_entry 26015166 1440049 18.07
ext4_dx_add_entry 25729337 1432814 17.96
ext4_mark_inode_dirty 12302433 5774407 2.13
most of cpu time blames to _raw_spin_lock, here is some testing
numbers with/without patch.
Test environment:
Server : SuperMicro Sever (2 x E5-2690 v3@2.60GHz, 128GB 2133MHz
DDR4 Memory, 8GbFC)
Storage : 2 x RAID1 (DDN SFA7700X, 4 x Toshiba PX02SMU020 200GB
Read Intensive SSD)
format command:
mkfs.ext4 -J size=4096
test command:
mpirun -np 48 mdtest -n 30000 -d /ext4/mdtest.out -F -C \
-r -i 1 -v -p 10 -u #first run to load inode
mpirun -np 48 mdtest -n 30000 -d /ext4/mdtest.out -F -C \
-r -i 3 -v -p 10 -u
Kernel version: 4.13.0-rc3
Test 1,440,000 files with 48 directories by 48 processes:
Without patch:
File Creation File removal
79,033 289,569 ops/per second
81,463 285,359
79,875 288,475
With patch:
File Creation File removal
810669 301694
812805 302711
813965 297670
Creation performance is improved more than 10X with large
journal size. The main problem here is we test bitmap
and do some check and journal operations which could be
slept, then we test and set with lock hold, this could
be racy, and make 'inode' steal by other process.
However, after first try, we could confirm handle has
been started and inode bitmap journaled too, then
we could find and set bit with lock hold directly, this
will mostly gurateee success with second try.
Tested-by: Shuichi Ihara <sihara@ddn.com>
Signed-off-by: Wang Shilong <wshilong@ddn.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Reviewed-by: Jan Kara <jack@suse.cz>
avoid duplicated codes, also we need goto
next group in case we found reserved inode.
Signed-off-by: Wang Shilong <wshilong@ddn.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Reviewed-by: Jan Kara <jack@suse.cz>
In recently_deleted() function we want to check whether inode is still
cached in buffer cache. Use sb_find_get_block() for that instead of
sb_getblk() to avoid unnecessary allocation of bdev page and buffer
heads.
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
This way we don't need a block_device structure to submit I/O. The
block_device has different life time rules from the gendisk and
request_queue and is usually only available when the block device node
is open. Other callers need to explicitly create one (e.g. the lightnvm
passthrough code, or the new nvme multipathing code).
For the actual I/O path all that we need is the gendisk, which exists
once per block device. But given that the block layer also does
partition remapping we additionally need a partition index, which is
used for said remapping in generic_make_request.
Note that all the block drivers generally want request_queue or
sometimes the gendisk, so this removes a layer of indirection all
over the stack.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
dq_data_lock is currently used to protect all modifications of quota
accounting information, consistency of quota accounting on the inode,
and dquot pointers from inode. As a result contention on the lock can be
pretty heavy.
Reduce the contention on the lock by protecting quota accounting
information by a new dquot->dq_dqb_lock and consistency of quota
accounting with inode usage by inode->i_lock.
This change reduces time to create 500000 files on ext4 on ramdisk by 50
different processes in separate directories by 6% when user quota is
turned on. When those 50 processes belong to 50 different users, the
improvement is about 9%.
Signed-off-by: Jan Kara <jack@suse.cz>
When journalling quotas, we writeback all dquots immediately after
changing them as part of current transation. Thus there's no need to
write anything in dquot_writeback_dquots() and so we can avoid updating
list of dirty dquots to reduce dq_list_lock contention.
This change reduces time to create 500000 files on ext4 on ramdisk by 50
different processes in separate directories by 15% when user quota is
turned on.
Signed-off-by: Jan Kara <jack@suse.cz>
When updating an extended attribute, if the padded value sizes are the
same, a shortcut is taken to avoid the bulk of the work. This was fine
until the xattr hash update was moved inside ext4_xattr_set_entry().
With that change, the hash update got missed in the shortcut case.
Thanks to ZhangYi (yizhang089@gmail.com) for root causing the problem.
Fixes: daf8328172 ("ext4: eliminate xattr entry e_hash recalculation for removes")
Reported-by: Miklos Szeredi <miklos@szeredi.hu>
Signed-off-by: Tahsin Erdogan <tahsin@google.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Arnd Bergmann <arnd@arndb.de>
As Stefan pointed out, I misremembered what clang can do specifically,
and it turns out that the variable-length array at the end of the
structure did not work (a flexible array would have worked here
but not solved the problem):
fs/ext4/mballoc.c:2303:17: error: fields must have a constant size:
'variable length array in structure' extension will never be supported
ext4_grpblk_t counters[blocksize_bits + 2];
This reverts part of my previous patch, using a fixed-size array
again, but keeping the check for the array overflow.
Fixes: 2df2c3402f ("ext4: fix warning about stack corruption")
Reported-by: Stefan Agner <stefan@agner.ch>
Tested-by: Chandan Rajendra <chandan@linux.vnet.ibm.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
This bug was found by a static code checker tool for copy paste
problems.
Signed-off-by: Maninder Singh <maninder1.s@samsung.com>
Signed-off-by: Vaneet Narang <v.narang@samsung.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
On a 32-bit platform, the value of n_blcoks_count may be wrong during
the file system is resized to size larger than 2^32 blocks. This may
caused the superblock being corrupted with zero blocks count.
Fixes: 1c6bd7173d
Signed-off-by: Jerry Lee <jerrylee@qnap.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Cc: stable@vger.kernel.org # 3.7+
When upgrading from old format, try to set project id
to old file first time, it will return EOVERFLOW, but if
that file is dirtied(touch etc), changing project id will
be allowed, this might be confusing for users, we could
try to expand @i_extra_isize here too.
Reported-by: Zhang Yi <yi.zhang@huawei.com>
Signed-off-by: Miao Xie <miaoxie@huawei.com>
Signed-off-by: Wang Shilong <wshilong@ddn.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Clean up some goto statement, make ext4_expand_extra_isize_ea() clearer.
Signed-off-by: Miao Xie <miaoxie@huawei.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Reviewed-by: Wang Shilong <wshilong@ddn.com>
Current ext4_expand_extra_isize just tries to expand extra isize, if
someone is holding xattr lock or some check fails, it will give up.
So rename its name to ext4_try_to_expand_extra_isize.
Besides that, we clean up unnecessary check and move some relative checks
into it.
Signed-off-by: Miao Xie <miaoxie@huawei.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Reviewed-by: Wang Shilong <wshilong@ddn.com>
We should avoid the contention between the i_extra_isize update and
the inline data insertion, so move the xattr trylock in front of
i_extra_isize update.
Signed-off-by: Miao Xie <miaoxie@huawei.com>
Reviewed-by: Wang Shilong <wshilong@ddn.com>
ext4_xattr_inode_read() currently reads each block sequentially while
waiting for io operation to complete before moving on to the next
block. This prevents request merging in block layer.
Add a ext4_bread_batch() function that starts reads for all blocks
then optionally waits for them to complete. A similar logic is used
in ext4_find_entry(), so update that code to use the new function.
Signed-off-by: Tahsin Erdogan <tahsin@google.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
When an xattr block has a single reference, block is updated inplace
and it is reinserted to the cache. Later, a cache lookup is performed
to see whether an existing block has the same contents. This cache
lookup will most of the time return the just inserted entry so
deduplication is not achieved.
Running the following test script will produce two xattr blocks which
can be observed in "File ACL: " line of debugfs output:
mke2fs -b 1024 -I 128 -F -O extent /dev/sdb 1G
mount /dev/sdb /mnt/sdb
touch /mnt/sdb/{x,y}
setfattr -n user.1 -v aaa /mnt/sdb/x
setfattr -n user.2 -v bbb /mnt/sdb/x
setfattr -n user.1 -v aaa /mnt/sdb/y
setfattr -n user.2 -v bbb /mnt/sdb/y
debugfs -R 'stat x' /dev/sdb | cat
debugfs -R 'stat y' /dev/sdb | cat
This patch defers the reinsertion to the cache so that we can locate
other blocks with the same contents.
Signed-off-by: Tahsin Erdogan <tahsin@google.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Reviewed-by: Andreas Dilger <adilger@dilger.ca>
ext4_alloc_file_blocks() does not use its mode parameter. Remove it.
Signed-off-by: Tahsin Erdogan <tahsin@google.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
After commit 62d1034f53e3 ("fortify: use WARN instead of BUG for now"),
we get a warning about possible stack overflow from a memcpy that
was not strictly bounded to the size of the local variable:
inlined from 'ext4_mb_seq_groups_show' at fs/ext4/mballoc.c:2322:2:
include/linux/string.h:309:9: error: '__builtin_memcpy': writing between 161 and 1116 bytes into a region of size 160 overflows the destination [-Werror=stringop-overflow=]
We actually had a bug here that would have been found by the warning,
but it was already fixed last year in commit 30a9d7afe7 ("ext4: fix
stack memory corruption with 64k block size").
This replaces the fixed-length structure on the stack with a variable-length
structure, using the correct upper bound that tells the compiler that
everything is really fine here. I also change the loop count to check
for the same upper bound for consistency, but the existing code is
already correct here.
Note that while clang won't allow certain kinds of variable-length arrays
in structures, this particular instance is fine, as the array is at the
end of the structure, and the size is strictly bounded.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
The dir_nlink feature has been enabled by default for new ext4
filesystems since e2fsprogs-1.41 in 2008, and was automatically
enabled by the kernel for older ext4 filesystems since the
dir_nlink feature was added with ext4 in kernel 2.6.28+ when
the subdirectory count exceeded EXT4_LINK_MAX-1.
Automatically adding the file system features such as dir_nlink is
generally frowned upon, since it could cause the file system to not be
mountable on older kernel, thus preventing the administrator from
rolling back to an older kernel if necessary.
In this case, the administrator might also want to disable the feature
because glibc's fts_read() function does not correctly optimize
directory traversal for directories that use st_nlinks field of 1 to
indicate that the number of links in the directory are not tracked by
the file system, and could fail to traverse the full directory
hierarchy. Fortunately, in the past ten years very few users have
complained about incomplete file system traversal by glibc's
fts_read().
This commit also changes ext4_inc_count() to allow i_nlinks to reach
the full EXT4_LINK_MAX links on the parent directory (including "."
and "..") before changing i_links_count to be 1.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=196405
Signed-off-by: Andreas Dilger <adilger@dilger.ca>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
I get a static checker warning:
fs/ext4/ext4.h:3091 ext4_set_de_type()
error: buffer overflow 'ext4_type_by_mode' 15 <= 15
It seems unlikely that we would hit this read overflow in real life, but
it's also simple enough to make the array 16 bytes instead of 15.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
ext4_find_unwritten_pgoff() does not properly handle a situation when
starting index is in the middle of a page and blocksize < pagesize. The
following command shows the bug on filesystem with 1k blocksize:
xfs_io -f -c "falloc 0 4k" \
-c "pwrite 1k 1k" \
-c "pwrite 3k 1k" \
-c "seek -a -r 0" foo
In this example, neither lseek(fd, 1024, SEEK_HOLE) nor lseek(fd, 2048,
SEEK_DATA) will return the correct result.
Fix the problem by neglecting buffers in a page before starting offset.
Reported-by: Andreas Gruenbacher <agruenba@redhat.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Jan Kara <jack@suse.cz>
CC: stable@vger.kernel.org # 3.8+
