Bspec states that we need to set nuke on modify all to prevent
screen corruption with fbc on skl and kbl.
v2: proper workaround name
References: HSD#2227109, HSDES#1404569388
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1465309159-30531-27-git-send-email-mika.kuoppala@intel.com
Set bit 8 in 0x43224 to prevent screen corruption and system
hangs on high memory bandwidth conditions. The same wa also suggest
setting bit 31 on ARB_CTL. According to another workaround we gain
better idle power savings when FBC is enabled.
v2: use correct workaround name
v3: split out overlapping wa for corruption avoidance (Ville)
References: HSD#2137218, HSD#2227171, HSD#2136579, BSID#883
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1465309159-30531-26-git-send-email-mika.kuoppala@intel.com
According to bspec this prevents screen corruption when fbc is
used.
v2: This workaround has a name, use it (Ville)
v3: remove bogus gen check on ilk/vlv wm path (Ville)
References: HSD#2135555, HSD#2137270, BSID#562
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1465309159-30531-25-git-send-email-mika.kuoppala@intel.com
According to bspec this workaround helps to reduce lag and improve
performance on edp.
Documentation suggests this for bdw and all gen9. However evidence
shows that this register is missing on gen9 and causing unclaimed mmio
access if we access it. So apply to bdw only where the reg
exists and can hold its value.
v2: drop skl
References: HSD#2134579
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1465309159-30531-11-git-send-email-mika.kuoppala@intel.com
if downscaling is enabled plane data rate increases according to scaling
amount. take scaling amount under consideration while calculating plane
data rate
v2: Address Matt's comments, where data rate was overridden because of
missing else.
v3 (by Matt):
- Add braces to 'else' branch to match kernel coding style
- Adjust final calculation now that skl_plane_downscale_amount()
returns 16.16 fixed point value instead of a decimal fixed point
v4 (by Matt):
- Avoid integer overflow by making sure final multiplication is
treated as 64-bit.
Cc: matthew.d.roper@intel.com
Signed-off-by: Kumar, Mahesh <mahesh1.kumar@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Kumar Mahesh <mahesh1.kumar@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463695381-21368-1-git-send-email-matthew.d.roper@intel.com
Don't use pipe pixel rate for plane pixel rate. Calculate plane pixel according
to formula
adjusted plane_pixel_rate = adjusted pipe_pixel_rate * downscale ammount
downscale amount = max[1, src_h/dst_h] * max[1, src_w/dst_w]
if 90/270 rotation use rotated width & height
v2: use intel_plane_state->visible instead of (fb == NULL) as per Matt's
comment.
v3 (by Matt):
- Keep downscale amount in 16.16 fixed point rather than converting to
decimal fixed point.
- Store adjusted plane pixel rate in plane state instead of the plane
parameters structure that we no longer use.
v4 (by Matt):
- Significant rebasing onto latest atomic watermark work
- Don't bother storing plane pixel rate in state; just calculate it
right before the calls that make use of it.
- Fix downscale calculations to actually use width values when
computing downscale_w rather than copy/pasted height values.
Cc: matthew.d.roper@intel.com
Signed-off-by: Kumar, Mahesh <mahesh1.kumar@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Kumar Mahesh <mahesh1.kumar@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463439121-28974-4-git-send-email-matthew.d.roper@intel.com
don't always use 8 ddb as minimum, instead calculate using proper
algorithm.
v2: optimizations as per Matt's comments.
v3 (by Matt):
- Fix boolean logic for !fb test in skl_ddb_min_alloc()
- Adjust negative tiling format comparisons in skl_ddb_min_alloc() to
improve readability.
v4 (by Matt):
- Rebase onto recent atomic watermark changes
- Slight tweaks to code flow to make the logic more closely match the
description in the bspec.
v5 (by Matt):
- Handle minimum scanline calculation properly for 4 & 8 bpp formats.
8bpp isn't actually possible right now, but it's listed in the bspec
so I've included it here for forward compatibility (similar to how
we have logic for NV12).
v6 (by Matt):
- Calculate plane_bpp correctly for non-NV12 formats. (Mahesh)
Cc: matthew.d.roper@intel.com
Signed-off-by: Kumar, Mahesh <mahesh1.kumar@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Kumar Mahesh <mahesh1.kumar@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1464713939-10440-1-git-send-email-matthew.d.roper@intel.com
We don't actually read out full plane state during driver startup (only
whether the primary plane is enabled/disabled), so all of the src/dest
rectangles are invalid at this point. However this calculation was
needless anyway since we re-calculate them from scratch on the very
first atomic transaction after boot anyway.
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Kumar Mahesh <mahesh1.kumar@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463439121-28974-2-git-send-email-matthew.d.roper@intel.com
I see the main drm pull got merged, here's the first batch of fixes for
4.7 already. Fixes all around, a large portion cc: stable stuff.
[airlied: the DP++ stuff is a regression fix].
* tag 'drm-intel-next-fixes-2016-05-25' of git://anongit.freedesktop.org/drm-intel:
drm/i915: Stop automatically retiring requests after a GPU hang
drm/i915: Unify intel_ring_begin()
drm/i915: Ignore stale wm register values on resume on ilk-bdw (v2)
drm/i915/psr: Try to program link training times correctly
drm/i915/bxt: Adjusting the error in horizontal timings retrieval
drm/i915: Don't leave old junk in ilk active watermarks on readout
drm/i915: s/DPPL/DPLL/ for SKL DPLLs
drm/i915: Fix gen8 semaphores id for legacy mode
drm/i915: Set crtc_state->lane_count for HDMI
drm/i915/BXT: Retrieving the horizontal timing for DSI
drm/i915: Protect gen7 irq_seqno_barrier with uncore lock
drm/i915: Re-enable GGTT earlier during resume on pre-gen6 platforms
drm/i915: Determine DP++ type 1 DVI adaptor presence based on VBT
drm/i915: Enable/disable TMDS output buffers in DP++ adaptor as needed
drm/i915: Respect DP++ adaptor TMDS clock limit
drm: Add helper for DP++ adaptors
Pull drm updates from Dave Airlie:
"Here's the main drm pull request for 4.7, it's been a busy one, and
I've been a bit more distracted in real life this merge window. Lots
more ARM drivers, not sure if it'll ever end. I think I've at least
one more coming the next merge window.
But changes are all over the place, support for AMD Polaris GPUs is in
here, some missing GM108 support for nouveau (found in some Lenovos),
a bunch of MST and skylake fixes.
I've also noticed a few fixes from Arnd in my inbox, that I'll try and
get in asap, but I didn't think they should hold this up.
New drivers:
- Hisilicon kirin display driver
- Mediatek MT8173 display driver
- ARC PGU - bitstreamer on Synopsys ARC SDP boards
- Allwinner A13 initial RGB output driver
- Analogix driver for DisplayPort IP found in exynos and rockchip
DRM Core:
- UAPI headers fixes and C++ safety
- DRM connector reference counting
- DisplayID mode parsing for Dell 5K monitors
- Removal of struct_mutex from drivers
- Connector registration cleanups
- MST robustness fixes
- MAINTAINERS updates
- Lockless GEM object freeing
- Generic fbdev deferred IO support
panel:
- Support for a bunch of new panels
i915:
- VBT refactoring
- PLL computation cleanups
- DSI support for BXT
- Color manager support
- More atomic patches
- GEM improvements
- GuC fw loading fixes
- DP detection fixes
- SKL GPU hang fixes
- Lots of BXT fixes
radeon/amdgpu:
- Initial Polaris support
- GPUVM/Scheduler/Clock/Power improvements
- ASYNC pageflip support
- New mesa feature support
nouveau:
- GM108 support
- Power sensor support improvements
- GR init + ucode fixes.
- Use GPU provided topology information
vmwgfx:
- Add host messaging support
gma500:
- Some cleanups and fixes
atmel:
- Bridge support
- Async atomic commit support
fsl-dcu:
- Timing controller for LCD support
- Pixel clock polarity support
rcar-du:
- Misc fixes
exynos:
- Pipeline clock support
- Exynoss4533 SoC support
- HW trigger mode support
- export HDMI_PHY clock
- DECON5433 fixes
- Use generic prime functions
- use DMA mapping APIs
rockchip:
- Lots of little fixes
vc4:
- Render node support
- Gamma ramp support
- DPI output support
msm:
- Mostly cleanups and fixes
- Conversion to generic struct fence
etnaviv:
- Fix for prime buffer handling
- Allow hangcheck to be coalesced with other wakeups
tegra:
- Gamme table size fix"
* 'drm-next' of git://people.freedesktop.org/~airlied/linux: (1050 commits)
drm/edid: add displayid detailed 1 timings to the modelist. (v1.1)
drm/edid: move displayid validation to it's own function.
drm/displayid: Iterate over all DisplayID blocks
drm/edid: move displayid tiled block parsing into separate function.
drm: Nuke ->vblank_disable_allowed
drm/vmwgfx: Report vmwgfx version to vmware.log
drm/vmwgfx: Add VMWare host messaging capability
drm/vmwgfx: Kill some lockdep warnings
drm/nouveau/gr/gf100-: fix race condition in fecs/gpccs ucode
drm/nouveau/core: recognise GM108 chipsets
drm/nouveau/gr/gm107-: fix touching non-existent ppcs in attrib cb setup
drm/nouveau/gr/gk104-: share implementation of ppc exception init
drm/nouveau/gr/gk104-: move rop_active_fbps init to nonctx
drm/nouveau/bios/pll: check BIT table version before trying to parse it
drm/nouveau/bios/pll: prevent oops when limits table can't be parsed
drm/nouveau/volt/gk104: round up in gk104_volt_set
drm/nouveau/fb/gm200: setup mmu debug buffer registers at init()
drm/nouveau/fb/gk20a,gm20b: setup mmu debug buffer registers at init()
drm/nouveau/fb/gf100-: allocate mmu debug buffers
drm/nouveau/fb: allow chipset-specific actions for oneinit()
...
For now, anything with a GuC requires uCode loading, and then supports
command submission once loaded. But these are logically distinct from
simply "having a GuC", so we need a separate macro for the latter. Then,
various tests should use this new macro rather than HAS_GUC_UCODE() or
testing enable_guc_submission.
v4:
Added a couple more uses of the new macro.
Signed-off-by: Dave Gordon <david.s.gordon@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
When we read out the watermark state from the hardware we're supposed to
transfer that into the active watermarks, but currently we fail to any
part of the active watermarks that isn't explicitly written. Let's clear
it all upfront.
Looks like this has been like this since the beginning, when I added the
readout. No idea why I didn't clear it up.
Cc: Matt Roper <matthew.d.roper@intel.com>
Fixes: 243e6a44b9 ("drm/i915: Init HSW watermark tracking in intel_modeset_setup_hw_state()")
Cc: stable@vger.kernel.org
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463151318-14719-2-git-send-email-ville.syrjala@linux.intel.com
(cherry picked from commit 15606534bf)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Found this while browsing Bspec. Looks like it applies to both skl and
kbl.
v2: Also for bxt (Art).
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Sonika Jindal <sonika.jindal@intel.com>
Cc: Durgadoss R <durgadoss.r@intel.com>
Cc: "Pandiyan, Dhinakaran" <dhinakaran.pandiyan@intel.com>
Cc: "Runyan, Arthur J" <arthur.j.runyan@intel.com>
Reviewed-by: Sonika Jindal<sonika.jindal@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463642060-30728-1-git-send-email-daniel.vetter@ffwll.ch
When we read out the watermark state from the hardware we're supposed to
transfer that into the active watermarks, but currently we fail to any
part of the active watermarks that isn't explicitly written. Let's clear
it all upfront.
Looks like this has been like this since the beginning, when I added the
readout. No idea why I didn't clear it up.
Cc: Matt Roper <matthew.d.roper@intel.com>
Fixes: 243e6a44b9 ("drm/i915: Init HSW watermark tracking in intel_modeset_setup_hw_state()")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463151318-14719-2-git-send-email-ville.syrjala@linux.intel.com
If we can't find any valid level 0 watermark values for the requested
atomic transaction, reject the configuration before we try to start
programming the hardware.
v2:
- Add extra debugging output when we reject level 0 watermarks so that
we can more easily debug how/why they were rejected.
Cc: Lyude Paul <cpaul@redhat.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463061971-19638-17-git-send-email-matthew.d.roper@intel.com
Moving watermark calculation into the check phase will allow us to to
reject display configurations for which there are no valid watermark
values before we start trying to program the hardware (although those
tests will come in a subsequent patch).
Another advantage of moving this calculation to the check phase is that
we can calculate the watermarks in a single shot as part of the atomic
transaction. The watermark interfaces we inherited from our legacy
modesetting days are a bit broken in the atomic design because they use
per-crtc entry points but actually re-calculate and re-program something
that is really more of a global state. That worked okay in the legacy
modesetting world because operations only ever updated a single CRTC at
a time. However in the atomic world, a transaction can involve multiple
CRTC's, which means we wind up computing and programming the watermarks
NxN times (where N is the number of CRTC's involved). With this patch
we eliminate the redundant re-calculation of watermark data for atomic
states (which was the cause of the WARN_ON(!wm_changed) problems that
have plagued us for a while).
We still need to work on the 'commit' side of watermark handling so that
we aren't doing redundant NxN programming of watermarks, but that's
content for future patches.
v2:
- Bail out of skl_write_wm_values() if the CRTC isn't active. Now that
we set dirty_pipes to ~0 if the active pipes change (because
we need to deal with DDB changes), we can now wind up here for
disabled pipes, whereas we couldn't before.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=89055
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=92181
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Tested-by: Daniel Stone <daniels@collabora.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463091100-13747-1-git-send-email-matthew.d.roper@intel.com
Once we move watermark calculation to the atomic check phase, we'll want
to start rejecting display configurations that exceed out watermark
limits. At the moment we just assume that there's always a valid set of
watermarks, even though this may not actually be true. Let's prepare by
passing return codes up through the call stack in preparation.
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463061971-19638-15-git-send-email-matthew.d.roper@intel.com
In an upcoming patch we'll move this calculation to the atomic 'check'
phase so that the display update can be rejected early if no valid
watermark programming is possible.
v2:
- Drop intel_pstate_for_cstate_plane() helper and add note about how
the code needs to evolve in the future if we start allowing more than
one pending commit against a CRTC. (Maarten)
v3:
- Only have skl_compute_wm_level calculate watermarks for enabled
planes; we can just set the other planes on a CRTC to disabled
without having to look at the plane state. This is important because
despite our CRTC lock we can still have racing commits that modify
a disabled plane's property without turning it on. (Maarten)
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463061971-19638-13-git-send-email-matthew.d.roper@intel.com
Now that we're properly pre-allocating the DDB during the atomic check
phase and we trust that the allocation is appropriate, let's actually
use the allocation computed and not duplicate that work during the
commit phase.
v2:
- Significant rebasing now that we can use cached data rates and
minimum block allocations to avoid grabbing additional plane states.
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463061971-19638-11-git-send-email-matthew.d.roper@intel.com
Calculate the DDB blocks needed to satisfy the current atomic
transaction at atomic check time. This is a prerequisite to calculating
SKL watermarks during the 'check' phase and rejecting any configurations
that we can't find valid watermarks for.
Due to the nature of DDB allocation, it's possible for the addition of a
new CRTC to make the watermark configuration already in use on another,
unchanged CRTC become invalid. A change in which CRTC's are active
triggers a recompute of the entire DDB, which unfortunately means we
need to disallow any other atomic commits from racing with such an
update. If the active CRTC's change, we need to grab the lock on all
CRTC's and run all CRTC's through their 'check' handler to recompute and
re-check their per-CRTC DDB allocations.
Note that with this patch we only compute the DDB allocation but we
don't actually use the computed values during watermark programming yet.
For ease of review/testing/bisecting, we still recompute the DDB at
watermark programming time and just WARN() if it doesn't match the
precomputed values. A future patch will switch over to using the
precomputed values once we're sure they're being properly computed.
Another clarifying note: DDB allocation itself shouldn't ever fail with
the algorithm we use today (i.e., we have enough DDB blocks on BXT to
support the minimum needs of the worst-case scenario of every pipe/plane
enabled at full size). However the watermarks calculations based on the
DDB may fail and we'll be moving those to the atomic check as well in
future patches.
v2:
- Skip DDB calculations in the rare case where our transaction doesn't
actually touch any CRTC's at all. Assuming at least one CRTC state
is present in our transaction, then it means we can't race with any
transactions that would update dev_priv->active_crtcs (which requires
_all_ CRTC locks).
v3:
- Also calculate DDB during initial hw readout, to prevent using
incorrect bios values. (Maarten)
v4:
- Use new distrust_bios_wm flag instead of skip_initial_wm (which was
never actually set).
- Set intel_state->active_pipe_changes instead of just realloc_pipes
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Lyude Paul <cpaul@redhat.com>
Cc: Radhakrishna Sripada <radhakrishna.sripada@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463061971-19638-10-git-send-email-matthew.d.roper@intel.com
SKL-style platforms can't fully trust the watermark/DDB settings
programmed by the BIOS and need to do extra sanitization on their first
atomic update. Add a flag to dev_priv that is set during hardware
readout and cleared at the end of the first commit.
Note that for the somewhat common case where everything is turned off
when the driver starts up, we don't need to bother with a recompute...we
know exactly what the DDB should be (all zero's) so just setup the DDB
directly in that case.
v2:
- Move clearing of distrust_bios_wm up below the swap_state call since
it's a more natural / self-explanatory location. (Maarten)
- Use dev_priv->active_crtcs to test whether any CRTC's are turned on
during HW WM readout rather than trying to count the active CRTC's
again ourselves. (Maarten)
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463061971-19638-9-git-send-email-matthew.d.roper@intel.com
We eventually want to calculate watermark values at atomic 'check' time
instead of atomic 'commit' time so that any requested configurations
that result in impossible watermark requirements are properly rejected.
The first step along this path is to allocate the DDB at atomic 'check'
time. As we perform this transition, allow the main allocation function
to operate successfully on either an in-flight state or an
already-commited state. Once we complete the transition in a future
patch, we'll come back and remove the unnecessary logic for the
already-committed case.
v2: Rebase/refactor; we should no longer need to grab extra plane states
while allocating the DDB since we can pull cached data rates and
minimum block counts from the CRTC state for any planes that aren't
being modified by this transaction.
v3:
- Simplify memsets to clear DDB plane entries. (Maarten)
- Drop a redundant memset of plane[pipe][PLANE_CURSOR] that was added
by an earlier Coccinelle patch. (Maarten)
- Assign *num_active at the top of skl_ddb_get_pipe_allocation_limits()
so that no code paths return without setting it. (kbuild robot)
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463061971-19638-8-git-send-email-matthew.d.roper@intel.com
This will eventually allow us to re-use old values without
re-calculating them for unchanged planes (which also helps us avoid
re-grabbing extra plane states).
v2:
- Drop unnecessary memset's; they were meant for a later patch (which
got reworked anyway to not need them, but were mis-rebased into this
one. (Maarten)
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463061971-19638-6-git-send-email-matthew.d.roper@intel.com
Our skl_get_total_relative_data_rate() function gets passed a crtc state
object to calculate the data rate for, but it currently always looks
up the committed plane states that correspond to that CRTC. Let's
check whether the CRTC state is an in-flight state (meaning
cstate->state is non-NULL) and if so, use the corresponding in-flight
plane states.
We'll soon be using this function exclusively for in-flight states; at
that time we'll be able to simplify the function a bit, but for now we
allow it to be used in either mode.
v2:
- Rebase on top of changes to cache plane data rates.
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463061971-19638-5-git-send-email-matthew.d.roper@intel.com
This will be important when we start calculating CRTC data rates for
in-flight CRTC states since it will allow us to calculate the total data
rate without needing to grab the plane state for any planes that aren't
updated by the transaction.
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463061971-19638-4-git-send-email-matthew.d.roper@intel.com
When we added atomic watermarks, we added a new display vfunc
'compute_pipe_wm' that is used to compute any pipe-specific watermark
information that we can at atomic check time. This was a somewhat poor
naming choice since we already had a 'skl_compute_pipe_wm' function that
doesn't quite fit this model --- the existing SKL function is something
that gets used at atomic commit time, after the DDB allocation has been
determined. Let's rename the existing SKL function to avoid confusion.
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463061971-19638-3-git-send-email-matthew.d.roper@intel.com
Reorganize the nested structures and unions we have for pipe watermark
data in intel_crtc_state so that platform-specific data can be added in
a more sensible manner (and save a bit of memory at the same time).
The change basically changes the organization from:
union {
struct intel_pipe_wm ilk;
struct intel_pipe_wm skl;
} optimal;
struct intel_pipe_wm intermediate /* ILK-only */
to
union {
struct {
struct intel_pipe_wm intermediate;
struct intel_pipe_wm optimal;
} ilk;
struct {
struct intel_pipe_wm optimal;
} skl;
}
There should be no functional change here, but it will allow us to add
more platform-specific fields going forward (and more easily extend to
other platform types like VLV).
While we're at it, let's move the entire watermark substructure out to
its own structure definition to make the code slightly more readable.
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463061971-19638-2-git-send-email-matthew.d.roper@intel.com
This way optimization from a previous patch works even better.
v2: Rebase.
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Pass drm_i915_private to the uncore init/fini routines and their
subservients as it is their native type.
text data bss dec hex filename
6309978 3578778 696320 10585076 a183f4 vmlinux
6309530 3578778 696320 10584628 a18234 vmlinux
a modest 400 bytes of saving, but 60 lines of code deleted!
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1462885804-26750-1-git-send-email-chris@chris-wilson.co.uk
Use the cdclk we're going to be using when the pipe gets enabled to
compute the IPS linetime watermark. The current cdclk frequency is
irrelevant at this point since it can still change.
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1461940278-17122-1-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
text data bss dec hex filename
6309351 3578714 696320 10584385 a18141 vmlinux
6308391 3578714 696320 10583425 a17d81 vmlinux
Almost 1KiB of code reduction.
v2: More s/INTEL_INFO()->gen/INTEL_GEN()/ and IS_GENx() conversions
text data bss dec hex filename
6304579 3578778 696320 10579677 a16edd vmlinux
6303427 3578778 696320 10578525 a16a5d vmlinux
Now over 1KiB!
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1462545621-30125-3-git-send-email-chris@chris-wilson.co.uk
I have noticed some of our interrupt handlers use both dev and
dev_priv while they could get away with only dev_priv in the
huge majority of cases.
Tidying that up had a cascading effect on changing functions
prototypes, so relatively big churn factor, but I think it is
for the better.
For example even where changes cascade out of i915_irq.c, for
functions prefixed with intel_, genX_ or <plat>_, it makes more
sense to take dev_priv directly anyway.
This allows us to eliminate local variables and intermixed usage
of dev and dev_priv where only one is good enough.
End result is shrinkage of both source and the resulting binary.
i915.ko:
- .text 000b0899
+ .text 000b0619
Or if we look at the Gen8 display irq chain:
-00000000000006ad t gen8_irq_handler
+0000000000000663 t gen8_irq_handler
-0000000000000028 T intel_opregion_asle_intr
+0000000000000024 T intel_opregion_asle_intr
-000000000000008c t ilk_hpd_irq_handler
+000000000000007f t ilk_hpd_irq_handler
-0000000000000116 T intel_check_page_flip
+0000000000000112 T intel_check_page_flip
-000000000000011a T intel_prepare_page_flip
+0000000000000119 T intel_prepare_page_flip
-0000000000000014 T intel_finish_page_flip_plane
+0000000000000013 T intel_finish_page_flip_plane
-0000000000000053 t hsw_pipe_crc_irq_handler
+000000000000004c t hsw_pipe_crc_irq_handler
-000000000000022e t cpt_irq_handler
+0000000000000213 t cpt_irq_handler
So small shrinkage but it is all fast paths so doesn't harm.
Situation is similar in other interrupt handlers as well.
v2: Tidy intel_queue_rps_boost_for_request as well. (Chris Wilson)
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
While browsing BSpec I bumped into a note saying we need to tune these
values based on actual measurements done after initial enabling. I've
checked that it indeed improves things on BXT. I haven't checked this on
CHV, but here it is if someone wants to give it a go.
v2:
- Add note about the discrepancy wrt. to the spec in the formula
calculating the credit encodings. (Mika, Ville)
- Move the WA comment to the new function. (Ville)
v3:
- Keep the comment about the SQC WA in the caller. (Ville)
CC: Ville Syrjälä <ville.syrjala@linux.intel.com>
CC: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1462280061-1457-4-git-send-email-imre.deak@intel.com
No need for hard-coding the register value, the corresponding fields are
defined properly in BSpec.
No functional change.
v2:
- Rebased on BXT L3 SQC tuning patch merged meanwhile.
CC: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> (v1)
Link: http://patchwork.freedesktop.org/patch/msgid/1462280061-1457-3-git-send-email-imre.deak@intel.com
If we move the release of the GEM request (i.e. decoupling it from the
various lists used for client and context tracking) after it is complete
(either by the GPU retiring the request, or by the caller cancelling the
request), we can remove the requirement that the final unreference of
the GEM request need to be under the struct_mutex.
The careful reader may notice that one or two impossible NULL pointer
tests are dropped for readability. These pointers cannot be NULL since
they are assigned during request construction and never unset.
v2,v3: Rebalance execlists by moving the context unpinning.
v4: Rebase onto -nightly
v5: Avoid trying to rebalance execlist/GuC context pinning, leave that
to the next step
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1461833819-3991-21-git-send-email-chris@chris-wilson.co.uk
As a part of WaGsvDisableTurbo, Driver makes an early exit from the
Gen9 Turbo enabling function, so doesn't program the Turbo Control register.
But BIOS could leave the Hw Turbo as enabled, so need to explicitly clear
out the Control register just to avoid inconsitency with debugfs
interface, which will show Turbo as enabled only and that is not expected
after adding the WaGsvDisableTurbo. Apart from this there is no problem
even if the Turbo is left enabled in the Control register, as the Up/Down
interrupts would remain masked.
v2: Add explicit clearing of Turbo Control register to *_disable_rps()
also for the similar consistency (Chris)
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Akash Goel <akash.goel@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/1461350146-23454-2-git-send-email-akash.goel@intel.com
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
On CHV GTFIFODBG has some read-only bits to indicate the number
of free FIFO entries. Ignore these when checking to see if any
of the sticky error bits are set.
This gets rid of these during device resume:
[drm:cherryview_enable_rps] GT fifo had a previous error 1080000
While at it, move the assignments out of the if().
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1460570970-14073-1-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The registers frobbed by vlv_init_display_clock_gating() libve inside
the disp2d power well, so frobbing them while the power well is down
results in unclaimed register access warning (and of course the values
won't stick). Let's do this setup after we know the power well is
enabled.
It's also worth noting that DSPCLK_GATE_D and CBR1_VLV lose their state
when the power well goes down, but fortunately the values we've been
writing are actually the reset defaults.
MI_ARB_VLV actually retains its value even if the power well was turned
off, we just can't access it while the power well is down.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=94164
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1460382992-28728-9-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>
Once again ILK is unhappy if we clear out the LP1+ watermark levels
outright, and instead we must disable the levels we don't want while
still leaving the actual programmed watermark levels intact.
Fixes underruns on the already enabled pipe when programming watermarks
while enabling the second pipe.
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Matt Roper <matthew.d.roper@intel.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=93787
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1459536799-18109-3-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>
dev_priv is what the macro works hard to extract, pass it directly.
> sed 's/\([A-Z].*(dev_priv\)->dev)/\1)/g'
v2:
- Include all wrapper macros too (Chris)
v3:
- Include sed cmdline (Chris)
v4:
- Break long line
- Rebase
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1460016485-8089-1-git-send-email-joonas.lahtinen@linux.intel.com
Currently we set the initial GPU frequency to min_freq_softlimit
on gen9, and to efficient_freq on VLV/CHV. On all the other platforms
we set it to idle_freq. Let's use idle_freq across the board to make
sure we don't waste power. This is especially relevant for VLV since
Vnn won't drop to minimum unless the GPU is at the minimum frequency.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1457120584-26080-3-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>
Extract the GPLL reference frequency from CCK and use it in the
GPU freq<->opcode conversions on VLV/CHV. This eliminates all the
assumptions we have about which divider is used for which czclk
frequency.
Note that unlike most clocks from CCK, the GPLL ref clock is a divided
down version of the CZ clock rather than the HPLL clock. CZ clock itself
is a divided down version of the HPLL clock though, so in effect it just
gets divided down twice.
While at it, throw in a few comments explaining the remaining constants
for anyone who later wants to compare this to the spreadsheets.
v2: Add slow/fast notes for CHV clocks (Imre)
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1457120584-26080-2-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com> (v1)
Refer to the GGTT VM consistently as "ggtt->base" instead of just "ggtt",
"vm" or indirectly through other variables like "dev_priv->ggtt.base"
to avoid confusion with the i915_ggtt object itself and PPGTT VMs.
Refer to the GGTT as "ggtt" instead of indirectly through chaining.
As a bonus gets rid of the long-standing i915_obj_to_ggtt vs.
i915_gem_obj_to_ggtt conflict, due to removal of i915_obj_to_ggtt!
v2:
- Added some more after grepping sources with Chris
v3:
- Refer to GGTT VM through ggtt->base consistently instead of ggtt_vm
(Chris)
v4:
- Convert all dev_priv->ggtt->foo accesses to ggtt->foo.
v5:
- Make patch checker happy
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Having provided for_each_engine_id() for cases where the third (id)
argument is useful, we can now replace all the remaining instances with
a simpler version that takes only two parameters. In many cases, this
also allows the elimination of the local variable used in the iterator
(usually 'i').
v2:
s/dev_priv/(dev_priv__)/ in body of for_each_engine_masked() [Chris Wilson]
Signed-off-by: Dave Gordon <david.s.gordon@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1458757194-17783-2-git-send-email-david.s.gordon@intel.com
Refer to Global GTT consistently as GGTT, thus rename dev_priv->gtt
to dev_priv->ggtt and struct i915_gtt to struct i915_ggtt.
Fix a couple of whitespace problems while at it.
v2:
- Fix a typo in commit message.
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Split out the part initing the clock gating hooks and move it earlier.
Add a new NOP hook for platforms without the need to apply clockgating
or workaround settings, so that the hook can be called unconditionally.
Also add a WARN for future platforms that forget to add a hook.
The rest of the hooks in intel_init_pm() should be inited in the same
way, but atm some of the hooks are set only conditionally, so before
doing this we need to make the setup unconditional and use instead some
flags.
v2:
- add a NOP hook and WARN if no hook is set for the platform (Chris)
- use the term hook instead of callback for these functions (Jani)
v3:
- remove the GEN4() check it's already covered by earlier platform
checks (Chris)
CC: Jani Nikula <jani.nikula@intel.com>
CC: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/1458128348-15730-6-git-send-email-imre.deak@intel.com
Some trivial ones, first pass done with Coccinelle:
@@
@@
(
- I915_NUM_RINGS
+ I915_NUM_ENGINES
|
- intel_ring_flag
+ intel_engine_flag
|
- for_each_ring
+ for_each_engine
|
- i915_gem_request_get_ring
+ i915_gem_request_get_engine
|
- intel_ring_idle
+ intel_engine_idle
|
- i915_gem_reset_ring_status
+ i915_gem_reset_engine_status
|
- i915_gem_reset_ring_cleanup
+ i915_gem_reset_engine_cleanup
|
- init_ring_lists
+ init_engine_lists
)
But that didn't fully work so I cleaned it up with:
for f in *.[hc]; do sed -i -e s/I915_NUM_RINGS/I915_NUM_ENGINES/ $f; done
for f in *.[hc]; do sed -i -e s/i915_gem_request_get_ring/i915_gem_request_get_engine/ $f; done
for f in *.[hc]; do sed -i -e s/intel_ring_flag/intel_engine_flag/ $f; done
for f in *.[hc]; do sed -i -e s/intel_ring_idle/intel_engine_idle/ $f; done
for f in *.[hc]; do sed -i -e s/init_ring_lists/init_engine_lists/ $f; done
for f in *.[hc]; do sed -i -e s/i915_gem_reset_ring_cleanup/i915_gem_reset_engine_cleanup/ $f; done
for f in *.[hc]; do sed -i -e s/i915_gem_reset_ring_status/i915_gem_reset_engine_status/ $f; done
v2: Rebase.
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Only planes that are part of the state should be used for recalculating
watermarks. For planes not part of the state the previous patch allows
us to re-use the old values since they're calculated even for levels
that are not actively used.
Changes since v1:
- Remove big if from intel_crtc_atomic_check.
- Remove extra newline.
- Remove memset in ilk_compute_pipe_wm.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Matt Roper <matthew.d.roper@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1456826842-32553-2-git-send-email-maarten.lankhorst@linux.intel.com
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
As Paulo has noted we can help bisectability by separating computing
watermarks on a noop in 2 separate commits.
This patch no longer clears the crtc watermark state, but recalculates
it completely. Regardless whether a level is used the full values for
each level are calculated. If a level is invalid wm[level].enable is
unset.
Changes since v1:
- Only call ilk_validate_wm_level when level <= usable_level. (Ville)
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/56D6D09E.5040007@linux.intel.com
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
This function returns an int, but when ilk_validate_pipe_wm fails it
returns false, which is 0 (success). As a result invalid watermarks
are applied, while they should have been rejected.
Fix this by returning -EINVAL.
Fixes: ed4a6a7ca8 ("drm/i915: Add two-stage ILK-style watermark programming (v11)")
Cc: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1456918563-28696-1-git-send-email-maarten.lankhorst@linux.intel.com
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
In addition to calculating final watermarks, let's also pre-calculate a
set of intermediate watermark values at atomic check time. These
intermediate watermarks are a combination of the watermarks for the old
state and the new state; they should satisfy the requirements of both
states which means they can be programmed immediately when we commit the
atomic state (without waiting for a vblank). Once the vblank does
happen, we can then re-program watermarks to the more optimal final
value.
v2: Significant rebasing/rewriting.
v3:
- Move 'need_postvbl_update' flag to CRTC state (Daniel)
- Don't forget to check intermediate watermark values for validity
(Maarten)
- Don't due async watermark optimization; just do it at the end of the
atomic transaction, after waiting for vblanks. We do want it to be
async eventually, but adding that now will cause more trouble for
Maarten's in-progress work. (Maarten)
- Don't allocate space in crtc_state for intermediate watermarks on
platforms that don't need it (gen9+).
- Move WaCxSRDisabledForSpriteScaling:ivb into intel_begin_crtc_commit
now that ilk_update_wm is gone.
v4:
- Add a wm_mutex to cover updates to intel_crtc->active and the
need_postvbl_update flag. Since we don't have async yet it isn't
terribly important yet, but might as well add it now.
- Change interface to program watermarks. Platforms will now expose
.initial_watermarks() and .optimize_watermarks() functions to do
watermark programming. These should lock wm_mutex, copy the
appropriate state values into intel_crtc->active, and then call
the internal program watermarks function.
v5:
- Skip intermediate watermark calculation/check during initial hardware
readout since we don't trust the existing HW values (and don't have
valid values of our own yet).
- Don't try to call .optimize_watermarks() on platforms that don't have
atomic watermarks yet. (Maarten)
v6:
- Rebase
v7:
- Further rebase
v8:
- A few minor indentation and line length fixes
v9:
- Yet another rebase since Maarten's patches reworked a bunch of the
code (wm_pre, wm_post, etc.) that this was previously based on.
v10:
- Move wm_mutex to dev_priv to protect against racing commits against
disjoint CRTC sets. (Maarten)
- Drop unnecessary clearing of cstate->wm.need_postvbl_update (Maarten)
v11:
- Now that we've moved to atomic watermark updates, make sure we call
the proper function to program watermarks in
{ironlake,haswell}_crtc_enable(); the failure to do so on the
previous patch iteration led to us not actually programming the
watermarks before turning on the CRTC, which was the cause of the
underruns that the CI system was seeing.
- Fix inverted logic for determining when to optimize watermarks. We
were needlessly optimizing when the intermediate/optimal values were
the same (harmless), but not actually optimizing when they differed
(also harmless, but wasteful from a power/bandwidth perspective).
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1456276813-5689-1-git-send-email-matthew.d.roper@intel.com
The assumption when adding the intel_display_power_is_enabled() checks
was that if it returns success the power can't be turned off afterwards
during the HW access, which is guaranteed by modeset locks. This isn't
always true, so make sure we hold a dedicated reference for the time of
the access.
Spotted-by: Mika Kuoppala <mika.kuoppala@intel.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=93441
CC: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1455719489-3008-1-git-send-email-imre.deak@intel.com
Code does read-modify-write but the read was outside the lock.
It is fine since the caller holds struct mutex, but if we
correct this we open up the opportunity for decreasing the
mutex duration time since the call to ironlake_enable_drps
does not need it any longer since it is covered by the
mchdev_lock lock.
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/1455186452-13691-2-git-send-email-tvrtko.ursulin@linux.intel.com
RPS lock must be taken before the struct_mutex to avoid
locking inversion. So stop grabbing it for the whole
powersave initialization and instead only take it during
the sections which need it.
Also, struct_mutex is not needed any more since dedicated
RPS lock was added in:
commit 4fc688ce79
Author: Jesse Barnes <jbarnes@virtuousgeek.org>
Date: Fri Nov 2 11:14:01 2012 -0700
drm/i915: protect RPS/RC6 related accesses (including PCU) with a new mutex
Based on prototype patch by Chris Wilson and a subsequent
mailing list discussion involving Ville, Imre, Chris and
Daniel.
v2: More details in the commit.
v3: Use drm_gem_object_unreference_unlocked. (Chris Wilson)
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
RC6 setup is shared between BIOS and Driver. BIOS sets up subset of RC6
setup registers. If those are not setup Driver should not enable RC6.
For implementing this, driver can check RC_CTRL0 and RC_CTRL1 values
to know if BIOS has enabled HW/SW RC6.
This will also enable user to control RC6 using BIOS settings alone.
RC6 related instability can be avoided by disabling via BIOS settings
till driver fixes it.
v2: Had placed logic in gen8 function by mistake. Fixed it.
Ensuring RPM is not enabled in case BIOS disabled RC6.
v3: Need to disable RPM if RC6 is disabled due to BIOS settings. (Daniel)
Runtime PM enabling happens before gen9_enable_rc6.
Moved the updation of enable_rc6 parameter in intel_uncore_sanitize.
v4: Added elaborate check for BIOS RC6 setup. Prepared check_pctx for bxt.
(Imre)
v5: Caching reserved stolen base and size in the driver private data.
Reorganized RC6 setup check. Moved from gen9_enable_rc6 to
intel_uncore_sanitize. (Imre)
v6: Rebasing on the patch submitted by Imre that moves gem_init_stolen
earlier in the load.
v7: Removed PWRCTX_MAXCNT_VCSUNIT1 check as it applies to SKL. (Imre)
v8: Fixed formatting and checkpatch issues. Fixed functional issue where
RC6 ctx size check was missing. (Imre)
Cc: Imre Deak <imre.deak@intel.com>
Signed-off-by: Sagar Arun Kamble <sagar.a.kamble@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1454697809-22113-1-git-send-email-sagar.a.kamble@intel.com
This reverts commit 396e33ae20.
This commit was triggering some FIFO underrun warnings on ILK-IVB
platforms (but surprisingly not on HSW/BDW that share more or less the
same codepaths). These underruns were caught by the continuous
integration (CI) system and could be reproduced consistently when
running the basic acceptance tests (BAT) on the affected platforms.
Note that this revert will cause a visible regression for some
end-users; the "flicker when mouse moves between monitors in X" issue
that was reported before this patch was merged will now return. However
regressions that are visible to CI have higher priority since they
prevent proper testing of future patches on those platforms. Hopefully
we'll be able to figure out the cause of the underruns quickly and
remerge an improved version of this patch to fix the regression.
Cc: Daniel Vetter <daniel@ffwll.ch>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=93640
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Daniel Vetter <daniel@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1453232584-8543-1-git-send-email-matthew.d.roper@intel.com
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
ilk_program_watermarks() is supposed to merge the active watermarks from
all pipes. Thus we need to use the active config too instead of some
precomputed stuff.
Fixes: aa36313686 ("drm/i915: Calculate watermark configuration during atomic check (v2)")
Cc: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1452776015-22076-2-git-send-email-ville.syrjala@linux.intel.com
ilk_compute_pipe_wm() assumes as zeroed pipe_wm structure when it
starts. We used to pass such a zeroed struct in, but this got broken
when the pipe_wm structure got embedded in the crtc state.
To fix it without too much fuzz, we need to resort to a memset().
Fixes: 4e0963c766 ("drm/i915: Calculate pipe watermarks into CRTC state (v3)")
Cc: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1452776015-22076-1-git-send-email-ville.syrjala@linux.intel.com
Add a common function to return "on" or "off" string based on the
argument, and drop the local versions of it.
This is the onoff version of
commit 42a8ca4cb4
Author: Jani Nikula <jani.nikula@intel.com>
Date: Thu Aug 27 16:23:30 2015 +0300
drm/i915: add yesno utility function
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1452768814-29787-1-git-send-email-jani.nikula@intel.com
In addition to calculating final watermarks, let's also pre-calculate a
set of intermediate watermark values at atomic check time. These
intermediate watermarks are a combination of the watermarks for the old
state and the new state; they should satisfy the requirements of both
states which means they can be programmed immediately when we commit the
atomic state (without waiting for a vblank). Once the vblank does
happen, we can then re-program watermarks to the more optimal final
value.
v2: Significant rebasing/rewriting.
v3:
- Move 'need_postvbl_update' flag to CRTC state (Daniel)
- Don't forget to check intermediate watermark values for validity
(Maarten)
- Don't due async watermark optimization; just do it at the end of the
atomic transaction, after waiting for vblanks. We do want it to be
async eventually, but adding that now will cause more trouble for
Maarten's in-progress work. (Maarten)
- Don't allocate space in crtc_state for intermediate watermarks on
platforms that don't need it (gen9+).
- Move WaCxSRDisabledForSpriteScaling:ivb into intel_begin_crtc_commit
now that ilk_update_wm is gone.
v4:
- Add a wm_mutex to cover updates to intel_crtc->active and the
need_postvbl_update flag. Since we don't have async yet it isn't
terribly important yet, but might as well add it now.
- Change interface to program watermarks. Platforms will now expose
.initial_watermarks() and .optimize_watermarks() functions to do
watermark programming. These should lock wm_mutex, copy the
appropriate state values into intel_crtc->active, and then call
the internal program watermarks function.
v5:
- Skip intermediate watermark calculation/check during initial hardware
readout since we don't trust the existing HW values (and don't have
valid values of our own yet).
- Don't try to call .optimize_watermarks() on platforms that don't have
atomic watermarks yet. (Maarten)
v6:
- Rebase
v7:
- Further rebase
v8:
- A few minor indentation and line length fixes
v9:
- Yet another rebase since Maarten's patches reworked a bunch of the
code (wm_pre, wm_post, etc.) that this was previously based on.
v10:
- Move wm_mutex to dev_priv to protect against racing commits against
disjoint CRTC sets. (Maarten)
- Drop unnecessary clearing of cstate->wm.need_postvbl_update (Maarten)
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1452108870-24204-1-git-send-email-matthew.d.roper@intel.com
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Although we can do a good job of reading out hardware state, the
graphics firmware may have programmed the watermarks in a creative way
that doesn't match how i915 would have chosen to program them. We
shouldn't trust the firmware's watermark programming, but should rather
re-calculate how we think WM's should be programmed and then shove those
values into the hardware.
We can do this pretty easily by creating a dummy top-level state,
running it through the check process to calculate all the values, and
then just programming the watermarks for each CRTC.
v2: Move watermark sanitization after our BIOS fb reconstruction; the
watermark calculations that we do here need to look at pstate->fb,
which isn't setup yet in intel_modeset_setup_hw_state(), even
though we have an enabled & visible plane.
v3:
- Don't move 'active = optimal' watermark assignment; we just undo
that change in the next patch anyway. (Ville)
- Move atomic helper locking fix to separate patch. (Maarten)
v4:
- Grab connection_mutex before calling atomic helper to duplicate
state. The connector loop inside the helper will throw a WARN
if we don't hold something to protect the connector list (and the
helper itself doesn't try to lock the list).
- Make failure to calculate watermarks for inherited state a WARN()
since it probably indicates a serious problem in either our state
readout code or our watermark code for this platform.
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
When watermark calculation was moved up to the atomic check phase, the
code was updated to calculate based on in-flight atomic state rather
than already-committed state. However the hsw_compute_linetime_wm()
didn't get updated and continued to pull values out of the
currently-committed CRTC state. On platforms that call this function
(HSW/BDW only), this will cause problems when we go to enable the CRTC
since we'll pull the current mode (off) rather than the mode we're
calculating for and wind up with a divide by zero error.
This was an oversight in commit:
commit a28170f338
Author: Matt Roper <matthew.d.roper@intel.com>
Date: Thu Sep 24 15:53:16 2015 -0700
drm/i915: Calculate ILK-style watermarks during atomic check (v3)
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1449171462-30763-5-git-send-email-matthew.d.roper@intel.com
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
commit 344df9809f ("drm/i915/skl: Disable coarse power gating up until F0")
failed to take into account that the same workaround is used in guc
when forcewake is sampled.
Wrap the condition check inside a macro and use it in both places
to fix the guc side scope.
Cc: Dave Gordon <david.s.gordon@intel.com>
Cc: Sagar Arun Kamble <sagar.a.kamble@intel.com>
Reviewed-by: Sagar Arun Kamble <sagar.a.kamble@intel.com>
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1450286318-6854-1-git-send-email-mika.kuoppala@intel.com
In some cases we want to check whether we hold an RPM wakelock reference
for the whole duration of a sequence. To achieve this add a new RPM
atomic sequence counter that we increment any time the wakelock refcount
drops to zero. Check whether the sequence number stays the same during
the atomic section and that we hold the wakelock at the beginning of the
section.
Motivated by Chris.
v2-v3:
- unchanged
v4:
- swap the order of atomic_read() and assert_rpm_wakelock_held() in
assert_rpm_atomic_begin() to avoid race
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> (v3)
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1450203038-5150-10-git-send-email-imre.deak@intel.com
Atm, we assert that the device is not suspended until the point when the
device is truly put to a suspended state. This is fine, but we can catch
more problems if we check that RPM refcount is non-zero. After that one
drops to zero we shouldn't access the device any more, even if the actual
device suspend may be delayed. Change assert_rpm_wakelock_held()
accordingly to check for a non-zero RPM refcount in addition to the
current device-not-suspended check.
For the new asserts to work we need to annotate every place explicitly in
the code where we expect that the device is powered. The places where we
only assume this, but may not hold an RPM reference:
- driver load
We assume the device to be powered until we enable RPM. Make this
explicit by taking an RPM reference around the load function.
- system and runtime sudpend/resume handlers
These handlers are called when the RPM reference becomes 0 and know the
exact point after which the device can get powered off. Disable the
RPM-reference-held check for their duration.
- the IRQ, hangcheck and RPS work handlers
These handlers are flushed in the system/runtime suspend handler
before the device is powered off, so it's guaranteed that they won't
run while the device is powered off even though they don't hold any
RPM reference. Disable the RPM-reference-held check for their duration.
In all these cases we still check that the device is not suspended.
These explicit annotations also have the positive side effect of
documenting our assumptions better.
This caught additional WARNs from the atomic modeset path, those should
be fixed separately.
v2:
- remove the redundant HAS_RUNTIME_PM check (moved to patch 1) (Ville)
v3:
- use a new dedicated RPM wakelock refcount to also catch cases where
our own RPM get/put functions were not called (Chris)
- assert also that the new RPM wakelock refcount is 0 in the RPM
suspend handler (Chris)
- change the assert error message to be more meaningful (Chris)
- prevent false assert errors and check that the RPM wakelock is 0 in
the RPM resume handler too
- prevent false assert errors in the hangcheck work too
- add a device not suspended assert check to the hangcheck work
v4:
- rename disable/enable_rpm_asserts to disable/enable_rpm_wakeref_asserts
and wakelock_count to wakeref_count
- disable the wakeref asserts in the IRQ handlers and RPS work too
- update/clarify commit message
v5:
- mark places we plan to change to use proper RPM refcounting with
separate DISABLE/ENABLE_RPM_WAKEREF_ASSERTS aliases (Chris)
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/1450227139-13471-1-git-send-email-imre.deak@intel.com
We can make the RPM dependency on RC6 explcit in the code by taking an
actual RPM reference, instead of avoiding to drop the initial one. This
will also enable us to remove the HAS_RUNTIME_PM special casing from
more places in the next patch.
v2:
- fixed typo in commit message (Joonas)
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1450203038-5150-4-git-send-email-imre.deak@intel.com
The cherryview device shares many characteristics with the valleyview
device. When support was added to the driver for cherryview, the
corresponding device info structure included .is_valleyview = 1.
This is not correct and leads to some confusion.
This patch changes .is_valleyview to .is_cherryview in the cherryview
device info structure and simplifies the IS_CHERRYVIEW macro.
Then where appropriate, instances of IS_VALLEYVIEW are replaced with
IS_VALLEYVIEW || IS_CHERRYVIEW or equivalent.
v2: Use IS_VALLEYVIEW || IS_CHERRYVIEW instead of defining a new macro.
Also add followup patches to fix issues discovered during the first
review. (Ville)
v3: Fix some style issues and one gen check. Remove CRT related changes
as CRT is not supported on CHV. (Imre, Ville)
v4: Make a few more optimizations. (Ville)
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Wayne Boyer <wayne.boyer@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1449692975-14803-1-git-send-email-wayne.boyer@intel.com
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Acked-by: Jani Nikula <jani.nikula@intel.com>
As described in the code comment, I couldn't set the minimum RPS
frequency on my BYT-M B0 to the minimum allowed as reported by Punit.
Fix this by clamping the minimum value to the first one that was
accepted on my machine.
Atm this issue doesn't cause any test failures, since in igt/pm_rps we
only check the cached version of the current frequency which is the same
what has been set. In the future we'll add checks for the actual
frequency too, and for that to pass this fix is necessary.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Acked-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1417711175-13271-1-git-send-email-imre.deak@intel.com
There is conflicting info between E0 and F0 steppings
for this workarounds. Trust more authoritative source and
be conservative and extend also for F0.
This prevents numerous (>50) gpu hangs with SKL GT4e
during piglit run.
References: HSD: gen9lp/2134184
Cc: Sagar Arun Kamble <sagar.a.kamble@intel.com>
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Sagar Arun Kamble <sagar.a.kamble@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1449505785-20812-1-git-send-email-mika.kuoppala@intel.com
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
The long term goal is to have enable/disable as the higher level
functions and activate/deactivate as the lower level functions, just
like we do for PSR and for the CRTC. This way, we'll run enable and
disable once per modeset, while update, activate and deactivate will
be run many times. With this, we can move the checks and code that
need to run only once per modeset to enable(), making the code simpler
and possibly a little faster.
This patch is just the first step on the conversion: it starts by
converting the current low level functions from enable/disable to
activate/deactivate. This patch by itself has no benefits other than
making review and rebase easier. Please see the next patches for more
details on the conversion.
v2:
- Rebase.
- Improve commit message (Chris).
v3: Rebase after changing the patch order.
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/
Per bspec, "Backlight PWM may stop in the asserted state, causing
backlight to stay fully on. WA: Before disabling PWM, set CLKGATE_DIS_0
0x46530 bit 13 PWM1 Gating Dis (for PWM1) or bit 14 PWM2 Gating Dis (for
PWM2). The bits can remain set without harm." (There's no workaround
name for this.)
This fixes some Broxton backlight issues.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
[Jani: cleanup & commit message]
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1448958232-26520-3-git-send-email-jani.nikula@intel.com
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJWUmHZAAoJEHm+PkMAQRiGHtcH/RVRsn8re0WdRWYaTr9+Hknm
CGlRJN4LKecttgYQ/2bS1QsDbt8usDPBiiYVopqGXQxPBmjyDAqPjsa+8VzCaVc6
WA+9LDB+PcW28lD6BO+qSZCOAm7hHSZq7dtw9x658IqO+mI2mVeCybsAyunw2iWi
Kf5q90wq6tIBXuT8YH9MXGrSCQw00NclbYeYwB9CmCt9hT/koEFBdl7uFUFitB+Q
GSPTz5fXhgc5Lms85n7flZlrVKoQKmtDQe4/DvKZm+SjsATHU9ru89OxDBdS5gSG
YcEIM4zc9tMjhs3GC9t6WXf6iFOdctum8HOhUoIN/+LVfeOMRRwAhRVqtGJ//Xw=
=DCUg
-----END PGP SIGNATURE-----
Merge tag 'v4.4-rc2' into drm-intel-next-queued
Linux 4.4-rc2
Backmerge to get at
commit 1b0e3a049e
Author: Imre Deak <imre.deak@intel.com>
Date: Thu Nov 5 23:04:11 2015 +0200
drm/i915/skl: disable display side power well support for now
so that we can proplery re-eanble skl power wells in -next.
Conflicts are just adjacent lines changed, except for intel_fbdev.c
where we need to interleave the changs. Nothing nefarious.
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Make I915_READ and I915_WRITE more type safe by wrapping the register
offset in a struct. This should eliminate most of the fumbles we've had
with misplaced parens.
This only takes care of normal mmio registers. We could extend the idea
to other register types and define each with its own struct. That way
you wouldn't be able to accidentally pass the wrong thing to a specific
register access function.
The gpio_reg setup is probably the ugliest thing left. But I figure I'd
just leave it for now, and wait for some divine inspiration to strike
before making it nice.
As for the generated code, it's actually a bit better sometimes. Eg.
looking at i915_irq_handler(), we can see the following change:
lea 0x70024(%rdx,%rax,1),%r9d
mov $0x1,%edx
- movslq %r9d,%r9
- mov %r9,%rsi
- mov %r9,-0x58(%rbp)
- callq *0xd8(%rbx)
+ mov %r9d,%esi
+ mov %r9d,-0x48(%rbp)
callq *0xd8(%rbx)
So previously gcc thought the register offset might be signed and
decided to sign extend it, just in case. The rest appears to be
mostly just minor shuffling of instructions.
v2: i915_mmio_reg_{offset,equal,valid}() helpers added
s/_REG/_MMIO/ in the register defines
mo more switch statements left to worry about
ring_emit stuff got sorted in a prep patch
cmd parser, lrc context and w/a batch buildup also in prep patch
vgpu stuff cleaned up and moved to a prep patch
all other unrelated changes split out
v3: Rebased due to BXT DSI/BLC, MOCS, etc.
v4: Rebased due to churn, s/i915_mmio_reg_t/i915_reg_t/
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/1447853606-2751-1-git-send-email-ville.syrjala@linux.intel.com
With gen < 9 we have had always 50Mhz units as our hw
ratio. With gen >= 9 the hw ratio changed to 16.667Mhz (50/3).
The result was that our gpu frequency tracing started to output
values 3 times larger than expected due to hardcoded scaling
value. Fix this by using Use intel_gpu_freq() when generating Mhz
value from ratio for 'intel_gpu_freq_change' trace event.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=92591
Cc: stable@vger.kernel.org # v4.3+
Reported-by: Eero Tamminen <eero.t.tamminen@intel.com>
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1447776866-29384-1-git-send-email-mika.kuoppala@intel.com
If ddb allocation for planes in current CRTC is changed, that doesn't
lead to ddb allocation change for other CRTCs, because our DDB allocation
is not dynamic according to plane parameters, ddb is allocated according
to number of CRTC enabled, & divided equally among CTRC's.
In current condition check during Watermark calculation, if number of
plane/ddb allocation changes for current CRTC, Watermark for other pipes
are recalculated. But there is no change in DDB allocation of other pipe
so watermark is also not changed, This leads to warning messages.
WARN_ON(!wm_changed)
This patch corrects this and check if DDB allocation for pipes is changed,
then only recalculate watermarks.
v2 (by Matt): Rebased to latest -nightly and fixed a typo
Signed-off-by: Kumar, Mahesh <mahesh1.kumar@intel.com>
Reviewed-by(v1): Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
When we set and later readback a frequency value through
sysfs interface, igt/pm_rpm assumes that we get same value back
if it matches hw granularity.
On bxt we have found out that this is not always the case.
Currently frequency - hw ratio - frequency conversions round down,
with few exceptions on platforms that have more specific conversions.
On bxt the supported range can be for example from 100Mhz to 650Mhz.
Midpoint is then calculated by test to be 375 which pm_rps uses to find a
closest hw supported frequency. That is 366 (ratio 22),
which it then writes back. But as the rounding down kicks in,
driver actually sets 350 instead of 366, as 366 is 2/3 below 22 * 50/3.
Fix this by rounding to closest instead of rounding down in
freq-ratio-freq conversions.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=92768
Testcase: igt/pm_rps/basic-api
Tested-by: Bob Paauwe <bob.j.paauwe@intel.com>
Cc: Bob Paauwe <bob.j.paauwe@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Bob Paauwe <bob.j.paauwe@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1447435781-23416-1-git-send-email-mika.kuoppala@intel.com
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
