Fix the following coccicheck warnings:
./drivers/net/ethernet/chelsio/cxgb4/cudbg_lib.c:3540:2-8: WARNING: NULL
check before some freeing functions is not needed.
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Jiapeng Chong <jiapeng.chong@linux.alibaba.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 0b5294483c ("net: dsa: mv88e6xxx: scratch: Fixup kerneldoc")
has addressed some but not all kerneldoc warnings for the Global 2
Scratch register accessors. Namely, we have some mismatches between
the function names in the kerneldoc and the ones in the actual code.
Let's adjust the comments so that they match the functions they're
sitting next to.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Michael Chan says:
====================
bnxt_en: Error recovery improvements.
This series contains some improvements for error recovery. The main
changes are:
1. Keep better track of the health register mappings with the
"status_reliable" flag.
2. Don't wait for firmware responses if firmware is not healthy.
3. Better retry logic of the first firmware message.
4. Set the proper flag early to let the RDMA driver know that firmware
reset has been detected.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Two enhancements:
1. Read the health status first before sending the first
HWRM_VER_GET message to firmware instead of the other way around.
This guarantees we got the accurate health status before we attempt
to send the message.
2. We currently only retry sending the first HWRM_VER_GET message to
the firmware if the firmware is in the process of booting. If the
firmware is in error state and is doing core dump for example, the
driver should also retry if the health register has the RECOVERING
flag set. This flag indicates the firmware will undergo recovery
soon. Modify the retry logic to retry for this case as well.
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Once the chip goes through reset, the register mapping may be lost
and any read of the mapped health registers may return garbage value
until the registers are mapped again in the init path.
Reading BNXT_FW_RESET_INPROG_REG after firmware reset will likely
return garbage value due to the above reason. Reading this register
is for information purpose only so remove it.
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During ifup, if the driver detects that firmware has gone through a
reset, it will go through a re-probe sequence. If the RDMA driver is
loaded, the re-probe sequence includes calling the RDMA driver to stop.
We need to set the BNXT_STATE_FW_RESET_DET flag earlier so that it is
visible to the RDMA driver. The RDMA driver's stop sequence is
different if firmware has gone through a reset.
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Reviewed-by: P B S Naresh Kumar <nareshkumar.pbs@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Check return value of call to bnxt_hwrm_func_resc_qcaps in
bnxt_hwrm_if_change and return failure on error.
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Scott Branden <scott.branden@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The original intent here is to allow commands during reset to succeed
without error when the device is disabled, to ensure that cleanup
completes normally during NIC close, where firmware is not necessarily
expected to respond.
The problem with faking success during reset's PCI disablement is that
unrelated ULP commands will also see inadvertent success during reset
when failure would otherwise be appropriate. It is better to return
a different error result such that reset related code can detect
this unique condition and ignore as appropriate.
Note, the pci_disable_device() when firmware is fatally wounded in
bnxt_fw_reset_close() does not need to be addressed, as subsequent
commands are already expected to fail due to the BNXT_NO_FW_ACCESS()
check in bnxt_hwrm_do_send_msg().
Reviewed-by: Scott Branden <scott.branden@broadcom.com>
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In situations where FW has crashed, the bnxt_hwrm_do_send_msg() call
will have to wait until timeout for each firmware message. This
generally takes about half a second for each firmware message. If we
try to unload the driver n this state, the unload sequence will take
a long time to complete.
Improve this by checking the health register if it is available and
abort the wait for the firmware response if the register shows that
firmware is not healthy. The very first message HWRM_VER_GET is
excluded from this check because that message is used to poll for
firmware to come out of reset during error recovery.
Signed-off-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to read the firmware health status, we first need to determine
the register location and then the register may need to be mapped.
There are 2 code paths to do this. The first one is done early as a
best effort attempt by the function bnxt_try_map_fw_health_reg(). The
second one is done later in the function bnxt_map_fw_health_regs()
after establishing communications with the firmware. We currently
only set fw_health->status_reliable if we can successfully set up the
health register in the first code path.
Improve the scheme by setting the fw_health->status_reliable flag if
either (or both) code paths can successfully set up the health
register. This flag is relied upon during run-time when we need to
check the health status. So this will make it work better.
During ifdown, if the health register is mapped, we need to invalidate
the health register mapping because a potential fw reset will reset
the mapping. Similarly, we need to do the same after firmware reset
during recovery. We'll remap it during ifup.
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Reviewed-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Huazhong Tan says:
====================
net: hns3: refactor and new features for flow director
This patchset refactor some functions and add some new features for
flow director.
patch 1~3: refactor large functions
patch 4, 7: add traffic class and user-def field support for ethtool
patch 5: refactor flow director configuration
patch 6: clean up for hns3_del_all_fd_entries()
change log:
V1->V2: modifies patch 5 as Jakub suggested, keep configuring
ethtool/tc flower rules synchronously while aRFS
asynchronously.
changes the usecnt of user-def rule checking in patch 7.
removes previous patches 8 and 9 from this series, since
there are issues that need further discussion.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
For DEVICE_VERSION_V3, the hardware supports to match specified
data in the specified offset of packet payload. Each layer can
have one offset, and can't be masked when configure flow director
rule by ethtool command. The layer is selected based on the
flow-type, ether for L2, ip4/ipv6 for L3, and tcp4/tcp6/udp4/udp6
for L4. For example, tcp4/tcp6/udp4/udp6 rules share the same
user-def offset, but each rule can have its own user-def value.
For the user-def field of ethtool -N/U command is 64 bits long.
The bit 0~15 is used for user-def value, and bit 32~47 for user-def
offset in HNS3 driver.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For only PF driver can configure flow director rule, it's
better to call hclge_del_all_fd_entries() directly in hclge
layer, rather than call hns3_del_all_fd_entries() in hns3
layer. Then the ae_algo->ops.del_all_fd_entries can be removed.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, the flow director rule of aRFS is configured in
the IO path. It's time-consuming. So move out the configuration,
and configure it asynchronously. And keep ethtool and tc flower
rule using synchronous way, otherwise the application maybe
unable to know the rule is installed or pending.
Add a state member for each flow director rule to indicate the
rule state. There are 4 states:
TO_ADD: the rule is waiting to add to hardware
TO_DEL: the rule is waiting to remove from hardware
DELETED: the rule has been removed from hardware. It's a middle
state, used to remove the rule node in the fd_rule_list.
ACTIVE: the rule is already added in hardware
For asynchronous way, when receive a new request to add or delete
flow director rule by aRFS, update the rule list, then request to
schedule the service task to finish the configuration.
For synchronous way, when receive a new request to add or delete
flow director rule by ethtool or tc flower, configure hardware
directly, then update the rule list if success.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The hardware supports to parse and match the traffic class field
of IPv6 packet for flow director, uses the same tuple as ip tos.
So removes the limitation of configure 'tclass' by driver.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, there are too many branches for hclge_fd_convert_tuple().
And it may be more when add new tuples. Refactor it by sorting the
tuples according to their length. So it only needs several KEY_OPT
now, and being flexible to add new tuples.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The process of function hclge_fd_get_tuple() is complex and
prolix. To make it more readable, extract the process of each
flow-type tuple to a single function.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The process of function hclge_add_fd_entry() is complex and
prolix. To make it more readable, extract the process of
fs->ring_cookie to a single function.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
s/unrequired/"not required"/
s/consme/consume/ .....two different places
s/accros/across/
Signed-off-by: Bhaskar Chowdhury <unixbhaskar@gmail.com>
Acked-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
s/subsytem/subsystem/
Signed-off-by: Bhaskar Chowdhury <unixbhaskar@gmail.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
s/packaet/packet/
Signed-off-by: Bhaskar Chowdhury <unixbhaskar@gmail.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
ic_close_dev contains a generalization of the logic to not close a
network interface if it's the host port for a DSA switch. This logic is
disguised behind an iteration through the lowers of ic_dev in
ic_close_dev.
When no interface for ipconfig can be found, ic_dev is NULL, and
ic_close_dev:
- dereferences a NULL pointer when assigning selected_dev
- would attempt to search through the lower interfaces of a NULL
net_device pointer
So we should protect against that case.
The "lower_dev" iterator variable was shortened to "lower" in order to
keep the 80 character limit.
Fixes: f68cbaed67 ("net: ipconfig: avoid use-after-free in ic_close_devs")
Fixes: 46acf7bdbc ("Revert "net: ipv4: handle DSA enabled master network devices"")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Tested-by: Heiko Thiery <heiko.thiery@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cristian Ciocaltea says:
====================
Add support for Actions Semi Owl Ethernet MAC
This patch series adds support for the Ethernet MAC found on the Actions
Semi Owl family of SoCs.
For the moment I have only tested the driver on RoseapplePi SBC, which is
based on the S500 SoC variant. It might work on S900 as well, but I cannot
tell for sure since the S900 datasheet I currently have doesn't provide
any information regarding the MAC registers - so I couldn't check the
compatibility with S500.
Similar story for S700: the datasheet I own is incomplete, but it seems
the MAC is advertised with Gigabit capabilities. For that reason most
probably we need to extend the current implementation in order to support
this SoC variant as well.
Please note that for testing the driver it is also necessary to update the
S500 clock subsystem:
https://lore.kernel.org/lkml/cover.1615221459.git.cristian.ciocaltea@gmail.com/
The DTS changes for the S500 SBCs will be provided separately.
Thanks,
Cristi
Changes in v3:
- Dropped the 'debug' module parameter and passed the default NETIF_MSG flags
to netif_msg_init(), according to David's review
- Removed the owl_emac_generate_mac_addr() function and the related
OWL_EMAC_GEN_ADDR_SYS_SN config option until a portable solution to get
the system serial number is found - when building on arm64 the following
error is thrown (as reported by Rob's kernel bot):
'[...]/owl-emac.c:9:10: fatal error: asm/system_info.h: No such file or directory'
- Rebased patchset on v5.12-rc4
Changes in v2:
* According to Philipp's review
- Requested exclusive control over serial line via
devm_reset_control_get_exclusive()
- Optimized error handling by using dev_err_probe()
* According to Andrew's review
- Dropped the inline keywords
- Applied Reverse Christmas Tree format to local variable declarations
- Renamed owl_emac_phy_config() to owl_emac_update_link_state()
- Documented the purpose of the special descriptor used in the context of
owl_emac_setup_frame_xmit()
- Updated comment inside owl_emac_mdio_clock_enable() regarding the MDC
clock divider setup
- Indicated MAC support for symmetric pause via phy_set_sym_pause()
in owl_emac_phy_init()
- Changed the MAC addr generation algorithm in owl_emac_generate_mac_addr()
by setting the locally administered bit in byte 0 and replacing bytes 1 & 2
with additional entries from enc_sn
- Moved devm_add_action_or_reset() before clk_set_rate() in owl_emac_probe()
* Other
- Added SMII interface support: updated owl_emac_core_sw_reset(), added
owl_emac_clk_set_rate(), updated description in the YAML binding
- Changed OWL_EMAC_TX_TIMEOUT from 0.05*HZ to 2*HZ
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Add entries for Actions Semi Owl Ethernet MAC binding and driver.
Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add new driver for the Ethernet MAC used on the Actions Semi Owl
family of SoCs.
Currently this has been tested only on the Actions Semi S500 SoC
variant.
Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add devicetree binding for the Ethernet MAC present on the Actions
Semi Owl family of SoCs.
For the moment advertise only the support for the Actions Semi S500 SoC
variant.
Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The existing code is functionally correct: iproute2 parses the ip_flags
argument for tc-flower and really packs it as big endian into the
TCA_FLOWER_KEY_FLAGS netlink attribute. But there is a problem in the
fact that W=1 builds complain:
net/sched/cls_flower.c:1047:15: warning: cast to restricted __be32
This is because we should use the dedicated helper for obtaining a
__be32 pointer to the netlink attribute, not a u32 one. This ensures
type correctness for be32_to_cpu.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A make W=1 build complains that:
net/sched/cls_flower.c:214:20: warning: cast from restricted __be16
net/sched/cls_flower.c:214:20: warning: incorrect type in argument 1 (different base types)
net/sched/cls_flower.c:214:20: expected unsigned short [usertype] val
net/sched/cls_flower.c:214:20: got restricted __be16 [usertype] dst
This is because we use htons on struct flow_dissector_key_ports members
src and dst, which are defined as __be16, so they are already in network
byte order, not host. The byte swap function for the other direction
should have been used.
Because htons and ntohs do the same thing (either both swap, or none
does), this change has no functional effect except to silence the
warnings.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a function to set the dynamic queue limit minimum value.
Some specific drivers might have legitimate reasons to configure
dql.min_limit to a given value. Typically, this is the case when the
PDU of the protocol is smaller than the packet size to used to
carry those frames to the device.
Concrete example: a CAN (Control Area Network) device with an USB 2.0
interface. The PDU of classical CAN protocol are roughly 16 bytes but
the USB packet size (which is used to carry the CAN frames to the
device) might be up to 512 bytes. Wen small traffic burst occurs, BQL
algorithm is not able to immediately adjust and this would result in
having to send many small USB packets (i.e packet of 16 bytes for each
CAN frame). Filling up the USB packet with CAN frames is relatively
fast (small latency issue) but the gain of not having to send several
small USB packets is huge (big throughput increase). In this case,
forcing dql.min_limit to a given value that would allow to stuff the
USB packet is always a win.
This function is to be used by network drivers which are able to prove
through a rationale and through empirical tests on several environment
(with other applications, heavy context switching, virtualization...),
that they constantly reach better performances with a specific
predefined dql.min_limit value with no noticeable latency impact.
Signed-off-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
There ended up being two sections with the same title. Combine the two
into one section.
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Cc: Manish Chopra <manishc@marvell.com>
Cc: Coiby Xu <coiby.xu@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
1. Remove CONFIG_HAVE_NET_DSA.
CONFIG_HAVE_NET_DSA is a legacy leftover from the times when drivers
should have selected CONFIG_NET_DSA manually.
Currently, all drivers has explicit 'depends on NET_DSA', so this is
no more needed.
2. CONFIG_HAVE_NET_DSA dependencies became CONFIG_NET_DSA's ones.
- dropped !S390 dependency which was introduced to be sure NET_DSA
can select CONFIG_PHYLIB. DSA migrated to Phylink almost 3 years
ago and the PHY library itself doesn't depend on !S390 since
commit 870a2b5e4f ("phylib: remove !S390 dependeny from Kconfig");
- INET dependency is kept to be sure we can select NET_SWITCHDEV;
- NETDEVICES dependency is kept to be sure we can select PHYLINK.
3. DSA drivers menu now depends on NET_DSA.
Instead on 'depends on NET_DSA' on every single driver, the entire
menu now depends on it. This eliminates a lot of duplicated lines
from Kconfig with no loss (when CONFIG_NET_DSA=m, drivers also can
be only m or n).
This also has a nice side effect that there's no more empty menu on
configurations without DSA.
4. Kbuild will now descend into 'drivers/net/dsa' only when
CONFIG_NET_DSA is y or m.
This is safe since no objects inside this folder can be built without
DSA core, as well as when CONFIG_NET_DSA=m, no objects can be
built-in.
Signed-off-by: Alexander Lobakin <alobakin@pm.me>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----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=mFaE
-----END PGP SIGNATURE-----
Merge tag 'selinux-pr-20210322' of git://git.kernel.org/pub/scm/linux/kernel/git/pcmoore/selinux
Pull selinux fixes from Paul Moore:
"Three SELinux patches:
- Fix a problem where a local variable is used outside its associated
function. Thankfully this can only be triggered by reloading the
SELinux policy, which is a restricted operation for other obvious
reasons.
- Fix some incorrect, and inconsistent, audit and printk messages
when loading the SELinux policy.
All three patches are relatively minor and have been through our
testing with no failures"
* tag 'selinux-pr-20210322' of git://git.kernel.org/pub/scm/linux/kernel/git/pcmoore/selinux:
selinuxfs: unify policy load error reporting
selinux: fix variable scope issue in live sidtab conversion
selinux: don't log MAC_POLICY_LOAD record on failed policy load
Flex-bytes allows for packet matching based on an offset and value. This
is supported via the ethtool user-def option.
The user-def 0xAAAABBBBCCCCDDDD: BBBB is the 2 byte pattern while AAAA
corresponds to its offset in the packet. Similarly DDDD is the 2 byte
pattern with CCCC being the corresponding offset. The offset ranges from
0x0 to 0x1F7 (up to 504 bytes into the packet). The offset starts from
the beginning of the packet.
This feature can be used to allow customers to set flow director rules
for protocols headers that are beyond standard ones supported by ethtool
(e.g. PFCP or GTP-U).
Like for matching GTP-U's TEID value 0x10203040:
ethtool -N ens787f0v0 flow-type udp4 dst-port 2152 \
user-def 0x002e102000303040 action 13
Signed-off-by: Haiyue Wang <haiyue.wang@intel.com>
Tested-by: Chen Bo <BoX.C.Chen@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Support the addition and deletion of Ethernet filters.
Supported fields are: proto
Supported flow-types are: ether
Example usage:
ethtool -N ens787f0v0 flow-type ether proto 0x8863 action 6
ethtool -N ens787f0v0 flow-type ether proto 0x8864 action 7
Signed-off-by: Haiyue Wang <haiyue.wang@intel.com>
Tested-by: Chen Bo <BoX.C.Chen@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Enable ethtool ntuple filter support on the VF driver using the virtchnl
interface to the PF driver and the Flow director functionality in the
hardware.
Signed-off-by: Haiyue Wang <haiyue.wang@intel.com>
Tested-by: Chen Bo <BoX.C.Chen@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Enable returning FDIR completion status by checking the
ctrl_vsi Rx queue descriptor value.
To enable returning FDIR completion status from ctrl_vsi Rx queue,
COMP_Queue and COMP_Report of FDIR filter programming descriptor
needs to be properly configured. After program request sent to ctrl_vsi
Tx queue, ctrl_vsi Rx queue interrupt will be triggered and
completion status will be returned.
Driver will first issue request in ice_vc_fdir_add_fltr(), then
pass FDIR context to the background task in interrupt service routine
ice_vc_fdir_irq_handler() and finally deal with them in
ice_flush_fdir_ctx(). ice_flush_fdir_ctx() will check the descriptor's
value, fdir context, and then send back virtual channel message to VF
by calling ice_vc_add_fdir_fltr_post(). An additional timer will be
setup in case of hardware interrupt timeout.
Signed-off-by: Yahui Cao <yahui.cao@intel.com>
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Qi Zhang <qi.z.zhang@intel.com>
Tested-by: Chen Bo <BoX.C.Chen@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Add new FDIR filter type to forward GTPU packets by matching TEID or QFI.
The filter is only enabled when COMMS DDP package is downloaded.
Signed-off-by: Yahui Cao <yahui.cao@intel.com>
Signed-off-by: Qi Zhang <qi.z.zhang@intel.com>
Tested-by: Chen Bo <BoX.C.Chen@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Add new filter type that allow forward non-IP Ethernet packets base on its
ethertype. The filter is only enabled when COMMS DDP package is loaded.
Signed-off-by: Yahui Cao <yahui.cao@intel.com>
Signed-off-by: Qi Zhang <qi.z.zhang@intel.com>
Tested-by: Chen Bo <BoX.C.Chen@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Add two new actions support for VF FDIR:
A passthrough action does not specify the destination queue, but
just allow the packet go to next pipeline stage, a typical use
cases is combined with a software mark (FDID) action.
Allow specify a 2^n continuous queues as the destination of a FDIR rule.
Packet distribution is based on current RSS configure.
Signed-off-by: Yahui Cao <yahui.cao@intel.com>
Signed-off-by: Qi Zhang <qi.z.zhang@intel.com>
Tested-by: Chen Bo <BoX.C.Chen@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Add basic FDIR flow list and pattern / action parse functions for VF.
Signed-off-by: Yahui Cao <yahui.cao@intel.com>
Signed-off-by: Qi Zhang <qi.z.zhang@intel.com>
Tested-by: Chen Bo <BoX.C.Chen@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The virtual channel is going to be extended to support FDIR and
RSS configure from AVF. New data structures and OP codes will be
added, the patch enable the FDIR part.
To support above advanced AVF feature, we need to figure out
what kind of data structure should be passed from VF to PF to describe
an FDIR rule or RSS config rule. The common part of the requirement is
we need a data structure to represent the input set selection of a rule's
hash key.
An input set selection is a group of fields be selected from one or more
network protocol layers that could be identified as a specific flow.
For example, select dst IP address from an IPv4 header combined with
dst port from the TCP header as the input set for an IPv4/TCP flow.
The patch adds a new data structure virtchnl_proto_hdrs to abstract
a network protocol headers group which is composed of layers of network
protocol header(virtchnl_proto_hdr).
A protocol header contains a 32 bits mask (field_selector) to describe
which fields are selected as input sets, as well as a header type
(enum virtchnl_proto_hdr_type). Each bit is mapped to a field in
enum virtchnl_proto_hdr_field guided by its header type.
+------------+-----------+------------------------------+
| | Proto Hdr | Header Type A |
| | +------------------------------+
| | | BIT 31 | ... | BIT 1 | BIT 0 |
| |-----------+------------------------------+
|Proto Hdrs | Proto Hdr | Header Type B |
| | +------------------------------+
| | | BIT 31 | ... | BIT 1 | BIT 0 |
| |-----------+------------------------------+
| | Proto Hdr | Header Type C |
| | +------------------------------+
| | | BIT 31 | ... | BIT 1 | BIT 0 |
| |-----------+------------------------------+
| | .... |
+-------------------------------------------------------+
All fields in enum virtchnl_proto_hdr_fields are grouped with header type
and the value of the first field of a header type is always 32 aligned.
enum proto_hdr_type {
header_type_A = 0;
header_type_B = 1;
....
}
enum proto_hdr_field {
/* header type A */
header_A_field_0 = 0,
header_A_field_1 = 1,
header_A_field_2 = 2,
header_A_field_3 = 3,
/* header type B */
header_B_field_0 = 32, // = header_type_B << 5
header_B_field_0 = 33,
header_B_field_0 = 34
header_B_field_0 = 35,
....
};
So we have:
proto_hdr_type = proto_hdr_field / 32
bit offset = proto_hdr_field % 32
To simply the protocol header's operations, couple help macros are added.
For example, to select src IP and dst port as input set for an IPv4/UDP
flow.
we have:
struct virtchnl_proto_hdr hdr[2];
VIRTCHNL_SET_PROTO_HDR_TYPE(&hdr[0], IPV4)
VIRTCHNL_ADD_PROTO_HDR_FIELD(&hdr[0], IPV4, SRC)
VIRTCHNL_SET_PROTO_HDR_TYPE(&hdr[1], UDP)
VIRTCHNL_ADD_PROTO_HDR_FIELD(&hdr[1], UDP, DST)
The byte array is used to store the protocol header of a training package.
The byte array must be network order.
The patch added virtual channel support for iAVF FDIR add/validate/delete
filter. iAVF FDIR is Flow Director for Intel Adaptive Virtual Function
which can direct Ethernet packets to the queues of the Network Interface
Card. Add/delete command is adding or deleting one rule for each virtual
channel message, while validate command is just verifying if this rule
is valid without any other operations.
To add or delete one rule, driver needs to config TCAM and Profile,
build training packets which contains the input set value, and send
the training packets through FDIR Tx queue. In addition, driver needs to
manage the software context to avoid adding duplicated rules, deleting
non-existent rule, input set conflicts and other invalid cases.
NOTE:
Supported pattern/actions and their parse functions are not be included in
this patch, they will be added in a separate one.
Signed-off-by: Jeff Guo <jia.guo@intel.com>
Signed-off-by: Yahui Cao <yahui.cao@intel.com>
Signed-off-by: Simei Su <simei.su@intel.com>
Signed-off-by: Beilei Xing <beilei.xing@intel.com>
Signed-off-by: Qi Zhang <qi.z.zhang@intel.com>
Tested-by: Chen Bo <BoX.C.Chen@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
We are going to enable FDIR configure for AVF through virtual channel.
The first step is to add helper functions to support control VSI setup.
A control VSI will be allocated for a VF when AVF creates its
first FDIR rule through ice_vf_ctrl_vsi_setup().
The patch will also allocate FDIR rule space for VF's control VSI.
If a VF asks for flow director rules, then those should come entirely
from the best effort pool and not from the guaranteed pool. The patch
allow a VF VSI to have only space in the best effort rules.
Signed-off-by: Xiaoyun Li <xiaoyun.li@intel.com>
Signed-off-by: Yahui Cao <yahui.cao@intel.com>
Signed-off-by: Qi Zhang <qi.z.zhang@intel.com>
Tested-by: Chen Bo <BoX.C.Chen@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Separate IPv4 and IPv6 ptype bit mask table into 2 tables:
with or without L4 protocols.
When a flow filter without any l4 type is specified, the
ICE_FLOW_SEG_HDR_IPV_OTHER flag can be used to describe if user
want to create a IP rule target for all IP packet or just IP
packet without l4 header.
Signed-off-by: Dan Nowlin <dan.nowlin@intel.com>
Signed-off-by: Qi Zhang <qi.z.zhang@intel.com>
Tested-by: Chen Bo <BoX.C.Chen@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
To apply different input set for GTP-U packet with or without extend
header as well as GTP-U uplink and downlink, we need to add TCAM mask
matching capability. This allows comprehending different PTYPE
attributes by examining flags from the parser. Using this method,
different profiles can be used by examining flag values from the parser.
Signed-off-by: Dan Nowlin <dan.nowlin@intel.com>
Signed-off-by: Qi Zhang <qi.z.zhang@intel.com>
Tested-by: Chen Bo <BoX.C.Chen@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Add more protocol support in flow filter, these
include PPPoE, L2TPv3, GTP, PFCP, ESP and AH.
Signed-off-by: Ting Xu <ting.xu@intel.com>
Signed-off-by: Yahui Cao <yahui.cao@intel.com>
Signed-off-by: Qi Zhang <qi.z.zhang@intel.com>
Tested-by: Chen Bo <BoX.C.Chen@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
To support FDIR input set with protocol field like DSCP, TTL,
PROT, etc. which is not word aligned, we need to enable field
vector masking.
Signed-off-by: Dan Nowlin <dan.nowlin@intel.com>
Signed-off-by: Qi Zhang <qi.z.zhang@intel.com>
Tested-by: Chen Bo <BoX.C.Chen@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Add more protocol and field support for flow filter include:
ETH, VLAN, ICMP, ARP and TCP flag.
Signed-off-by: Kevin Scott <kevin.c.scott@intel.com>
Signed-off-by: Qi Zhang <qi.z.zhang@intel.com>
Tested-by: Chen Bo <BoX.C.Chen@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
