Commit Graph

157 Commits

Author SHA1 Message Date
David Daney
38c3c0f673 MIPS: OCTEON: Improve _machine_halt implementation.
As noted by Wladislav Wiebe:
   $ halt
   ..
   Sent SIGKILL to all processes
   Requesting system halt
   [66.729373] System halted.
   [66.733244]
   [66.734761] =====================================
   [66.739473] [ BUG: lock held at task exit time! ]
   [66.744188] 3.8.7-0-sampleversion-fct #49 Tainted: G           O
   [66.750202] -------------------------------------
   [66.754913] init/21479 is exiting with locks still held!
   [66.760234] 1 lock held by init/21479:
   [66.763990]  #0:  (reboot_mutex){+.+...}, at: [<ffffffff801776c8>] SyS_reboot+0xe0/0x218
   [66.772165]
   [66.772165] stack backtrace:
   [66.776532] Call Trace:
   [66.778992] [<ffffffff805780a8>] dump_stack+0x8/0x34
   [66.783972] [<ffffffff801618b0>] do_exit+0x610/0xa70
   [66.788948] [<ffffffff801777a8>] SyS_reboot+0x1c0/0x218
   [66.794186] [<ffffffff8013d6a4>] handle_sys64+0x44/0x64

This is an alternative fix to the one sent by Wladislav.  We kill the
watchdog for each CPU and then spin in WAIT with interrupts disabled.
This is the lowest power mode for the OCTEON.  If we were to spin with
interrupts enabled, we would get a continual stream of warning messages
and backtraces from the lockup detector, so I chose to disable
interrupts.

Signed-off-by: David Daney <david.daney@cavium.com>
Cc: Maxim Uvarov <muvarov@gmail.com>
Cc: Wladislav Wiebe <wladislav.kw@gmail.com>
Cc: linux-mips@linux-mips.org
Cc: David Daney <david.daney@cavium.com>
Patchwork: https://patchwork.linux-mips.org/patch/5324/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2013-06-06 16:11:26 +02:00
Alexander Sverdlin
d41d547a41 MIPS: octeon: Fix GPIO number in IRQ chip private data
Current GPIO chip implementation in octeon-irq is still broken, even after upstream
commit 87161ccdc6 (MIPS: Octeon: Fix broken interrupt
controller code). It works for GPIO IRQs that have reset-default configuration, but
not for edge-triggered ones.

The problem is in octeon_irq_gpio_map_common(), which passes modified "hw" variable
(which has range of possible values 16..31) as "gpio_line" parameter to
octeon_irq_set_ciu_mapping(), which saves it in private data of the IRQ chip. Later,
neither octeon_irq_gpio_setup() is able to re-configure GPIOs (cvmx_write_csr() is
writing to non-existent CVMX_GPIO_BIT_CFGX), nor octeon_irq_ciu_gpio_ack() is able
to acknowledge such IRQ, because "mask" is incorrect.

Fix is trivial and has been tested on Cavium Octeon II -based board, including
both level-triggered and edge-triggered GPIO IRQs.

Signed-off-by: Alexander Sverdlin <alexander.sverdlin.ext@nsn.com>
Cc: David Daney <david.daney@cavium.com>
Acked-by: David Daney <david.daney@cavium.com>
Patchwork: http://patchwork.linux-mips.org/patch/4980/
Acked-by: John Crispin <blogic@openwrt.org>
2013-05-08 01:19:07 +02:00
EunBong Song
ed1197f931 MIPS: Fix build error cavium-octeon without CONFIG_SMP
Singed-off-by: EunBong Song <eunb.song@samsung.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2013-04-05 15:10:39 +02:00
Linus Torvalds
aebb2afd54 Merge branch 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus
Pull MIPS updates from Ralf Baechle:

 o Add basic support for the Mediatek/Ralink Wireless SoC family.

 o The Qualcomm Atheros platform is extended by support for the new
   QCA955X SoC series as well as a bunch of patches that get the code
   ready for OF support.

 o Lantiq and BCM47XX platform have a few improvements and bug fixes.

 o MIPS has sent a few patches that get the kernel ready for the
   upcoming microMIPS support.

 o The rest of the series is made up of small bug fixes and cleanups
   that relate to various parts of the MIPS code.  The biggy in there is
   a whitespace cleanup.  After I was sent another set of whitespace
   cleanup patches I decided it was the time to clean the whitespace
   "issues" for once and and that touches many files below arch/mips/.

Fix up silly conflicts, mostly due to whitespace cleanups.

* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (105 commits)
  MIPS: Quit exporting kernel internel break codes to uapi/asm/break.h
  MIPS: remove broken conditional inside vpe loader code
  MIPS: SMTC: fix implicit declaration of set_vi_handler
  MIPS: early_printk: drop __init annotations
  MIPS: Probe for and report hardware virtualization support.
  MIPS: ath79: add support for the Qualcomm Atheros AP136-010 board
  MIPS: ath79: add USB controller registration code for the QCA955X SoCs
  MIPS: ath79: add PCI controller registration code for the QCA955X SoCs
  MIPS: ath79: add WMAC registration code for the QCA955X SoCs
  MIPS: ath79: register UART for the QCA955X SoCs
  MIPS: ath79: add QCA955X specific glue to ath79_device_reset_{set, clear}
  MIPS: ath79: add GPIO setup code for the QCA955X SoCs
  MIPS: ath79: add IRQ handling code for the QCA955X SoCs
  MIPS: ath79: add clock setup code for the QCA955X SoCs
  MIPS: ath79: add SoC detection code for the QCA955X SoCs
  MIPS: ath79: add early printk support for the QCA955X SoCs
  MIPS: ath79: fix WMAC IRQ resource assignment
  mips: reserve elfcorehdr
  mips: Make sure kernel memory is in iomem
  MIPS: ath79: use dynamically allocated USB platform devices
  ...
2013-03-02 07:44:16 -08:00
Linus Torvalds
2ef14f465b Merge branch 'x86-mm-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 mm changes from Peter Anvin:
 "This is a huge set of several partly interrelated (and concurrently
  developed) changes, which is why the branch history is messier than
  one would like.

  The *really* big items are two humonguous patchsets mostly developed
  by Yinghai Lu at my request, which completely revamps the way we
  create initial page tables.  In particular, rather than estimating how
  much memory we will need for page tables and then build them into that
  memory -- a calculation that has shown to be incredibly fragile -- we
  now build them (on 64 bits) with the aid of a "pseudo-linear mode" --
  a #PF handler which creates temporary page tables on demand.

  This has several advantages:

  1. It makes it much easier to support things that need access to data
     very early (a followon patchset uses this to load microcode way
     early in the kernel startup).

  2. It allows the kernel and all the kernel data objects to be invoked
     from above the 4 GB limit.  This allows kdump to work on very large
     systems.

  3. It greatly reduces the difference between Xen and native (Xen's
     equivalent of the #PF handler are the temporary page tables created
     by the domain builder), eliminating a bunch of fragile hooks.

  The patch series also gets us a bit closer to W^X.

  Additional work in this pull is the 64-bit get_user() work which you
  were also involved with, and a bunch of cleanups/speedups to
  __phys_addr()/__pa()."

* 'x86-mm-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (105 commits)
  x86, mm: Move reserving low memory later in initialization
  x86, doc: Clarify the use of asm("%edx") in uaccess.h
  x86, mm: Redesign get_user with a __builtin_choose_expr hack
  x86: Be consistent with data size in getuser.S
  x86, mm: Use a bitfield to mask nuisance get_user() warnings
  x86/kvm: Fix compile warning in kvm_register_steal_time()
  x86-32: Add support for 64bit get_user()
  x86-32, mm: Remove reference to alloc_remap()
  x86-32, mm: Remove reference to resume_map_numa_kva()
  x86-32, mm: Rip out x86_32 NUMA remapping code
  x86/numa: Use __pa_nodebug() instead
  x86: Don't panic if can not alloc buffer for swiotlb
  mm: Add alloc_bootmem_low_pages_nopanic()
  x86, 64bit, mm: hibernate use generic mapping_init
  x86, 64bit, mm: Mark data/bss/brk to nx
  x86: Merge early kernel reserve for 32bit and 64bit
  x86: Add Crash kernel low reservation
  x86, kdump: Remove crashkernel range find limit for 64bit
  memblock: Add memblock_mem_size()
  x86, boot: Not need to check setup_header version for setup_data
  ...
2013-02-21 18:06:55 -08:00
Linus Torvalds
9afa3195b9 Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial
Pull trivial tree from Jiri Kosina:
 "Assorted tiny fixes queued in trivial tree"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (22 commits)
  DocBook: update EXPORT_SYMBOL entry to point at export.h
  Documentation: update top level 00-INDEX file with new additions
  ARM: at91/ide: remove unsused at91-ide Kconfig entry
  percpu_counter.h: comment code for better readability
  x86, efi: fix comment typo in head_32.S
  IB: cxgb3: delay freeing mem untill entirely done with it
  net: mvneta: remove unneeded version.h include
  time: x86: report_lost_ticks doesn't exist any more
  pcmcia: avoid static analysis complaint about use-after-free
  fs/jfs: Fix typo in comment : 'how may' -> 'how many'
  of: add missing documentation for of_platform_populate()
  btrfs: remove unnecessary cur_trans set before goto loop in join_transaction
  sound: soc: Fix typo in sound/codecs
  treewide: Fix typo in various drivers
  btrfs: fix comment typos
  Update ibmvscsi module name in Kconfig.
  powerpc: fix typo (utilties -> utilities)
  of: fix spelling mistake in comment
  h8300: Fix home page URL in h8300/README
  xtensa: Fix home page URL in Kconfig
  ...
2013-02-21 17:40:58 -08:00
Venkat Subbiah
0e49caf661 MIPS: Octeon: Adding driver to measure interrupt latency on Octeon.
Signed-off-by: Venkat Subbiah <venkat.subbiah@cavium.com>
[Rewrote timeing calculations]
Signed-off-by: David Daney <david.daney@cavium.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/4660/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2013-02-15 23:07:37 +01:00
Ralf Baechle
7034228792 MIPS: Whitespace cleanup.
Having received another series of whitespace patches I decided to do this
once and for all rather than dealing with this kind of patches trickling
in forever.

Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2013-02-01 10:00:22 +01:00
Yinghai Lu
ac2cbab21f x86: Don't panic if can not alloc buffer for swiotlb
Normal boot path on system with iommu support:
swiotlb buffer will be allocated early at first and then try to initialize
iommu, if iommu for intel or AMD could setup properly, swiotlb buffer
will be freed.

The early allocating is with bootmem, and could panic when we try to use
kdump with buffer above 4G only, or with memmap to limit mem under 4G.
for example: memmap=4095M$1M to remove memory under 4G.

According to Eric, add _nopanic version and no_iotlb_memory to fail
map single later if swiotlb is still needed.

-v2: don't pass nopanic, and use -ENOMEM return value according to Eric.
     panic early instead of using swiotlb_full to panic...according to Eric/Konrad.
-v3: make swiotlb_init to be notpanic, but will affect:
     arm64, ia64, powerpc, tile, unicore32, x86.
-v4: cleanup swiotlb_init by removing swiotlb_init_with_default_size.

Suggested-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Link: http://lkml.kernel.org/r/1359058816-7615-36-git-send-email-yinghai@kernel.org
Reviewed-and-tested-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Jeremy Fitzhardinge <jeremy@goop.org>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Cc: linux-mips@linux-mips.org
Cc: xen-devel@lists.xensource.com
Cc: virtualization@lists.linux-foundation.org
Cc: Shuah Khan <shuahkhan@gmail.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
2013-01-29 19:36:53 -08:00
Jiri Kosina
617677295b Merge branch 'master' into for-next
Conflicts:
	drivers/devfreq/exynos4_bus.c

Sync with Linus' tree to be able to apply patches that are
against newer code (mvneta).
2013-01-29 10:48:30 +01:00
Ralf Baechle
757be67f56 MIPS: Octeon: Fix warning.
Cong Ding <dinggnu@gmail.com> reports correctly that the variable dummy
is being used without initialization.  That said, I can't reproduce this
warning with GCC 4.7.1.  However, since the variable dummy servces no
real purpose, I'm going for a different fix.  This fix
includes https://patchwork.linux-mips.org/patch/4801/ plus Geert's
suggestion to use ACCESS_ONCE().

Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2013-01-22 18:07:46 +01:00
Greg Kroah-Hartman
28eb0e4661 MIPS: drivers: remove __dev* attributes.
CONFIG_HOTPLUG is going away as an option.  As a result, the __dev*
markings need to be removed.

This change removes the use of __devinit, __devexit_p, __devinitdata,
and __devexit from these drivers.

Based on patches originally written by Bill Pemberton, but redone by me
in order to handle some of the coding style issues better, by hand.

Cc: Bill Pemberton <wfp5p@virginia.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-01-03 15:57:09 -08:00
Jorrit Schippers
d82603c6da treewide: Replace incomming with incoming in all comments and strings
Signed-off-by: Jorrit Schippers <jorrit@ncode.nl>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
2013-01-03 16:15:49 +01:00
Linus Torvalds
cebfa85eb8 Merge branch 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus
Pull MIPS updates from Ralf Baechle:
 "The MIPS bits for 3.8.  This also includes a bunch fixes that were
  sitting in the linux-mips.org git tree for a long time.  This pull
  request contains updates to several OCTEON drivers and the board
  support code for BCM47XX, BCM63XX, XLP, XLR, XLS, lantiq, Loongson1B,
  updates to the SSB bus support, MIPS kexec code and adds support for
  kdump.

  When pulling this, there are two expected merge conflicts in
  include/linux/bcma/bcma_driver_chipcommon.h which are trivial to
  resolve, just remove the conflict markers and keep both alternatives."

* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (90 commits)
  MIPS: PMC-Sierra Yosemite: Remove support.
  VIDEO: Newport Fix console crashes
  MIPS: wrppmc: Fix build of PCI code.
  MIPS: IP22/IP28: Fix build of EISA code.
  MIPS: RB532: Fix build of prom code.
  MIPS: PowerTV: Fix build.
  MIPS: IP27: Correct fucked grammar in ops-bridge.c
  MIPS: Highmem: Fix build error if CONFIG_DEBUG_HIGHMEM is disabled
  MIPS: Fix potencial corruption
  MIPS: Fix for warning from FPU emulation code
  MIPS: Handle COP3 Unusable exception as COP1X for FP emulation
  MIPS: Fix poweroff failure when HOTPLUG_CPU configured.
  MIPS: MT: Fix build with CONFIG_UIDGID_STRICT_TYPE_CHECKS=y
  MIPS: Remove unused smvp.h
  MIPS/EDAC: Improve OCTEON EDAC support.
  MIPS: OCTEON: Add definitions for OCTEON memory contoller registers.
  MIPS: OCTEON: Add OCTEON family definitions to octeon-model.h
  ata: pata_octeon_cf: Use correct byte order for DMA in when built little-endian.
  MIPS/OCTEON/ata: Convert pata_octeon_cf.c to use device tree.
  MIPS: Remove usage of CEVT_R4K_LIB config option.
  ...
2012-12-14 14:27:45 -08:00
Ralf Baechle
241738bd51 Merge branch 'mips-next' of http://dev.phrozen.org/githttp/mips-next into mips-for-linux-next 2012-12-13 19:40:13 +01:00
David Daney
e1ced09797 MIPS/EDAC: Improve OCTEON EDAC support.
Some initialization errors are reported with the existing OCTEON EDAC
support patch.  Also some parts have more than one memory controller.

Fix the errors and add multiple controllers if present.

Signed-off-by: David Daney <david.daney@cavium.com>
2012-12-13 18:15:26 +01:00
David Daney
43f01da0f2 MIPS/OCTEON/ata: Convert pata_octeon_cf.c to use device tree.
The patch needs to eliminate the definition of OCTEON_IRQ_BOOTDMA so
that the device tree code can map the interrupt, so in order to not
temporarily break things, we do a single patch to both the interrupt
registration code and the pata_octeon_cf driver.

Also rolled in is a conversion to use hrtimers and corrections to the
timing calculations.

Acked-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: David Daney <david.daney@cavium.com>
2012-12-13 18:15:24 +01:00
Ralf Baechle
abe77f90dc MIPS: Octeon: Add kexec and kdump support
[ralf@linux-mips.org: Original patch by Maxim Uvarov <muvarov@gmail.com>
with plenty of further shining, polishing, debugging and testing by me.]

Signed-off-by: Maxim Uvarov <muvarov@gmail.com>
Cc: linux-mips@linux-mips.org
Cc: kexec@lists.infradead.org
Cc: horms@verge.net.au
Patchwork: https://patchwork.linux-mips.org/patch/1026/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2012-12-13 17:00:39 +01:00
Ralf Baechle
5456bd26ae MIPS: Octeon: Simplify code by assuming CONFIG_64BIT is always set.
No 32-bit kernels supported on Octeon.

Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2012-12-12 16:52:06 +01:00
Ralf Baechle
4fe64af7da MIPS: Octeon: Remove use of CONFIG_64BIT_PHYS_ADDR.
Only supporting 64-bit kernels there is no point in depending on
this symbol.

Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2012-12-12 16:52:06 +01:00
Ralf Baechle
ce4625f431 MIPS: Octeon: Remove highmem code.
On Cavium hardware only 64-bit kernels are supported so CONFIG_HIGHMEM
is never set.

Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2012-12-12 16:52:06 +01:00
Ralf Baechle
f65aad4177 MIPS: Cavium: Add EDAC support.
Drivers for EDAC on Cavium.  Supported subsystems are:

 o CPU primary caches.  These are parity protected only, so only error
   reporting.
 o Second level cache - ECC protected, provides SECDED.
 o Memory: ECC / SECDEC if used with suitable DRAM modules.  The driver will
   will only initialize if ECC is enabled on a system so is safe to run on
   non-ECC memory.
 o PCI: Parity error reporting

Since it is very hard to test this sort of code the implementation is very
conservative and uses polling where possible for now.

Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Reviewed-by: Borislav Petkov <borislav.petkov@amd.com>
2012-12-12 16:48:49 +01:00
Linus Torvalds
b58ed041a3 Device tree changes for v3.8
Bug fixes, little cleanups, and documentation changes. The most invasive
 thing here touches a bunch of the arch directories to use a common build
 rule for .dtb files. There are no major changes to functionality here
 other than a ew new helper functions.
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v1.4.11 (GNU/Linux)
 
 iQIcBAABAgAGBQJQx2/sAAoJEEFnBt12D9kB8aYP/iInsIXDi6c0sGRNgYoFBZUH
 pGZH/PGcZjDD2WPUOos56KTDsWt2kIZm/4ck1mBmXMD5pKM4znIQyMTkhKFiyO0l
 CARwCjyRuaHQJHt88Pcaqhk34HGLgV7ntImMHwpIn0mNbjx7hruk9aU9Jqdcd32j
 2ANbUYU9ikgq0e9s/+xQfB6QZxH1zecQkMalhQWvihtVybpG3xW67IROZv/69uL0
 OtHZZJ7nCwXcEb84rcEHU781tO0CoQhr/pId7DirQEKaD8oNLHsejFEgGEFfFrvZ
 eFmJP/YmZh7Ll+NNTMHnQwyDNa2LFuLazbjaqCqUHQgcw9daFFeP5ga3Uqp7WZbU
 4kIxBQJ3byELnttFVQbsMQag+IAgmgfp8YdJFk3VTJDJKwpMJAO1sQeoEUHnnWAr
 cyyCzROaFt1hUkhRiXso+IYNLvb60o0/2NJRTiObPdljy9OSXW6O3wFEGk9F/6u0
 jgl9tisfLUL0orKnJ5tR3kbHaJKQd+6HgBRJNiuB+9FYO43j1cY/sYggSNCkiCMy
 RvlGYDCJ+lfmZdZ4T+QYLpjsOenFosV0JZGU6MVlZmEGzTtLyhALZQKNHuxLw1Nc
 oTe8Fx5aJrWEYe/HGqm4C43DqEiQUCmZ9NPae0JyfocmjuwARSnepvWe1XZNa/8t
 aNfK6UkTO/IL3zOtOHfd
 =LB3n
 -----END PGP SIGNATURE-----

Merge tag 'devicetree-for-linus' of git://git.secretlab.ca/git/linux-2.6

Pull device tree changes from Grant Likely:
 "Here are the DT changes I've got queued up for v3.8.  As described
  below, there are a lot of bug fixes here and documentation updates but
  nothing major:

  Bug fixes, little cleanups, and documentation changes.  The most
  invasive thing here touches a bunch of the arch directories to use a
  common build rule for .dtb files.  There are no major changes to
  functionality here other than a few new helper functions."

* tag 'devicetree-for-linus' of git://git.secretlab.ca/git/linux-2.6: (34 commits)
  arm64: Fix the dtbs target building
  mtd: nand: davinci: fix the binding documentation
  rtc: rtc-mv: Add the device tree binding documentation
  devicetree/bindings: Move gpio-leds binding into leds directory
  of/vendor-prefixes: add Imagination Technologies
  microblaze: use new common dtc rule
  c6x: use new common dtc rule
  openrisc: use new common dtc rule
  arm64: Add dtbs target for building all the enabled dtb files
  arm64: use new common dtc rule
  ARM: dt: change .dtb build rules to build in dts directory
  kbuild: centralize .dts->.dtb rule
  Fix build when CONFIG_W1_MASTER_GPIO=m b exporting "allnodes"
  of/spi: Honour "status=disabled" property of device
  of_mdio: Honour "status=disabled" property of device
  of_i2c: Honour "status=disabled" property of device
  powerpc: Fix fallout from device_node->name constification
  of: add 'const' for of_parse_phandle parameter *np
  Documentation: correct of_platform_populate() argument list
  script: dtc: clean generated files
  ...
2012-12-11 11:30:41 -08:00
Stephen Warren
90b335fbbc kbuild: centralize .dts->.dtb rule
All architectures that use cmd_dtc do so in almost the same way. Create
a central build rule to avoid duplication. The one difference is that
most current uses of dtc build $(obj)/%.dtb from $(src)/dts/%.dts rather
than building the .dtb in the same directory as the .dts file. This
difference will be eliminated arch-by-arch in future patches.

MIPS is the exception here; it already uses the exact same rule as the
new common rule, so the duplicate is removed in this patch to avoid any
conflict. arch/mips changes courtesy of Ralf Baechle.

Update Documentation/kbuild to remove the explicit call to cmd_dtc from
the example, now that the rule exists in a centralized location.

Cc: Arnd Bergmann <arnd@arndb.de>
Cc: linux-arm-kernel@lists.infradead.org
Cc: Olof Johansson <olof@lixom.net>
Cc: Russell King <linux@arm.linux.org.uk>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Cc: Jonas Bonn <jonas@southpole.se>
Cc: linux@lists.openrisc.net
Cc: Aurelien Jacquiot <a-jacquiot@ti.com>
Cc: linux-c6x-dev@linux-c6x.org
Cc: Mark Salter <msalter@redhat.com>
Cc: Michal Simek <monstr@monstr.eu>
Cc: microblaze-uclinux@itee.uq.edu.au
Cc: Chris Zankel <chris@zankel.net>
Cc: linux-xtensa@linux-xtensa.org
Cc: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
2012-11-30 10:52:19 -06:00
Charles Hardin
0f731711af mips/octeon: 16-Bit NOR flash was not being detected during boot
The cavium code assumed that all NOR on the boot bus was
an 8-bit NOR part and hardcoded the bankwidth. The simple
solution was to add the code that queries the configuration
register for the width of the bus that has been hardware strapped
to the Cavium. This allows both 8-bit and 16-bit parts to be
discovered during boot.

Acked-by: David Daney <david.daney@cavium.com>
Signed-off-by: Charles Hardin <ckhardin@exablox.com>
Patchwork: http://patchwork.linux-mips.org/patch/4323
Signed-off-by: John Crispin <blogic@openwrt.org>
2012-11-09 11:37:16 +01:00
Jim Quinlan
92d11594f6 MIPS: Remove irqflags.h dependency from bitops.h
The "else clause" of most functions in bitops.h invoked
raw_local_irq_{save,restore}() and in doing so had a dependency on
irqflags.h.  This fix moves said code to bitops.c, removing the
dependency.

Signed-off-by: Jim Quinlan <jim2101024@gmail.com>
Cc: linux-mips@linux-mips.org
Cc: David Daney <ddaney.cavm@gmail.com>
Cc: Kevin Cernekee cernekee@gmail.com
Cc: Jim Quinlan <jim2101024@gmail.com>
Patchwork: https://patchwork.linux-mips.org/patch/4320/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2012-11-09 10:59:10 +01:00
Linus Torvalds
de390bba79 Merge branch 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus
Pull MIPS update from Ralf Baechle:
 "This is the MIPS update for 3.7.

  A fair chunk of them are platform updates to the Cavium Octeon SOC
  (which involves machine generated header files of considerable size),
  Atheros ATH79xx, RMI aka Netlogic aka Broadcom XLP, Broadcom BCM63xx
  platforms.

  Support for the commercial MIPS simulator MIPSsim has been removed as
  MIPS Technologies is shifting away from this product and Qemu is
  offering various more powerful platforms.  The generic MIPS code can
  now also probe for no-execute / write-only TLB features implemented
  without the full SmartMIPS extension as permitted by the latest MIPS
  processor architecture.  Lots of small changes to generic code."

* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (78 commits)
  MIPS: ath79: Fix CPU/DDR frequency calculation for SRIF PLLs
  MIPS: ath79: use correct fractional dividers for {CPU,DDR}_PLL on AR934x
  MIPS: BCM63XX: Properly handle mac address octet overflow
  MIPS: Kconfig: Avoid build errors by hiding USE_OF from the user.
  MIPS: Replace `-' in defconfig filename wth `_' for consistency.
  MIPS: Wire kcmp syscall.
  MIPS: MIPSsim: Remove the MIPSsim platform.
  MIPS: NOTIFY_RESUME is not needed in TIF masks
  MIPS: Merge the identical "return from syscall" per-ABI code
  MIPS: Unobfuscate _TIF..._MASK
  MIPS: Prevent hitting do_notify_resume() with !user_mode(regs).
  MIPS: Replace 'kernel_uses_smartmips_rixi' with 'cpu_has_rixi'.
  MIPS: Add base architecture support for RI and XI.
  MIPS: Optimise TLB handlers for MIPS32/64 R2 cores.
  MIPS: uasm: Add INS and EXT instructions.
  MIPS: Avoid pipeline stalls on some MIPS32R2 cores.
  MIPS: Make VPE count to be one-based.
  MIPS: Add new end of interrupt functionality for GIC.
  MIPS: Add EIC support for GIC.
  MIPS: Code clean-ups for the GIC.
  ...
2012-10-09 16:08:04 +09:00
Ralf Baechle
e33fd70bae Merge branch 'cn6xxx-mgmt' of git://git.linux-mips.org/pub/scm/daney/upstream-daney into mips-for-linux-next 2012-09-27 18:00:34 +02:00
Greg Kroah-Hartman
7ac3c93e5d Merge 3.6-rc6 into tty-next
This pulls in the fixes in 3.6-rc6

Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2012-09-16 17:31:36 -07:00
David Daney
70a26a219c MIPS: Octeon: Add octeon_io_clk_delay() function.
Also cleanup and fix octeon_init_cvmcount()

Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Acked-by: David S. Miller <davem@davemloft.net>
2012-08-31 11:48:48 -07:00
David Daney
c9f0f0c0e1 MIPS: OCTEON: Register ciu/ciu2 as the default irq_domain.
This makes it possible to call irq_create_mapping(NULL, ??)

Signed-off-by: David Daney <david.daney@cavium.com>
2012-08-31 10:46:54 -07:00
David Daney
1a7e68f2c7 MIPS: Octeon: Make interrupt controller work with threaded handlers.
For CIUv1 controllers, we were relying on all calls to the irq_chip
functions to be done from the CPU that received the irq, and that they
would all be done from interrupt contest.  These assumptions do not
hold for threaded handlers.

We make all the masking actually mask the irq source, and use real
raw_spin_locks instead of manually twiddling the Status[IE] bit.

Signed-off-by: David Daney <david.daney@cavium.com>
2012-08-31 10:46:54 -07:00
David Daney
88fd85892a MIPS: OCTEON: Add support for cn68XX interrupt controller.
The cn68XX has a new interrupt controller named CIU2, add support for
this, and use it if cn68XX detected at runtime.

Signed-off-by: David Daney <david.daney@cavium.com>
2012-08-31 10:46:54 -07:00
David Daney
c5aa59e88f MIPS: OCTEON: Update register definitions.
Add support for cn68xx, cn61xx, cn63xx, cn66xx and cnf71XX.

Add little-endian register layouts.

Patch cvmx-interrupt-rsl.c for changed definition.

Signed-off-by: David Daney <david.daney@cavium.com>
2012-08-31 10:46:53 -07:00
David Daney
87161ccdc6 MIPS: Octeon: Fix broken interrupt controller code.
Since 3.6.0-rc1,  We are getting many messages like:

WARNING: at kernel/irq/irqdomain.c:444 irq_domain_associate_many+0x23c/0x260()
Modules linked in:
Call Trace:
[<ffffffff814cb698>] dump_stack+0x8/0x34
[<ffffffff81133d00>] warn_slowpath_common+0x78/0xa8
[<ffffffff81187e44>] irq_domain_associate_many+0x23c/0x260
[<ffffffff81187f38>] irq_create_mapping+0xd0/0x220
[<ffffffff81188104>] irq_create_of_mapping+0x7c/0x158
[<ffffffff813e5f08>] irq_of_parse_and_map+0x28/0x40
.
.
.

Both the CIU and GPIO interrupt domains were somewhat screwed up.

For the CIU domain, we need to call irq_domain_associate() for each of
the preassigned irq numbers.  For the GPIO domain, we were applying
the register bit offset in octeon_irq_gpio_xlat, but it should be done
in octeon_irq_gpio_map instead.

Also: Reserve all 8 'core' irqs for the 'core' irq_chip so that they
don't get used by the other domains.  Remove unused OCTEON_IRQ_*
symbols.

Signed-off-by: David Daney <david.daney@cavium.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/4190/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2012-08-17 10:57:26 +02:00
David Daney
640de636a1 MIPS: OCTEON: Fix breakage due to 8250 changes.
The changes in linux-next removing serial8250_register_port() cause
OCTEON to fail to compile.

Lets make OCTEON use the new serial8250_register_8250_port() instead.

Signed-off-by: David Daney <david.daney@cavium.com>
Cc: Alan Cox <alan@linux.intel.com>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2012-08-14 14:54:31 -07:00
Ralf Baechle
68d8848567 Merge branches 'next/generic', 'next/alchemy', 'next/bcm63xx', 'next/cavium', 'next/jz4740', 'next/lantiq', 'next/loongson1b' and 'next/netlogic' into mips-for-linux-next 2012-07-25 16:37:46 +02:00
David Daney
a03822ea5d MIPS: OCTEON: Remove some unused files.
These FPA related files are not used anywhere in the kernel.  Remove
them.

Signed-off-by: David Daney <david.daney@cavium.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/3892/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2012-07-24 16:33:09 +02:00
David Daney
914f848077 MIPS: Octeon: Implement Octeon specific __copy_user_inatomic
The generic version seems to prefetch past the end of memory.

Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/3929/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2012-07-23 13:55:55 +01:00
David Daney
b59b284101 MIPS: Octeon: Use device tree to register serial ports.
Switch to using the device tree to register serial ports.

Add all the ports with compatible = "cavium,octeon-3860-uart".  Octeon serial
ports have their own device type, required port flags, and I/O
functions, so using of_serial.c is not indicated.

We need to do this as late_initcall, as the 8250 driver must be
initialized before we add any ports.  8250 initialization is done at
device_initcall time.

The OCTEON_IRQ_UART{0,1,2} symbols are removed as they are now unused
and interfere with irq_domain used by the device tree code.

Signed-off-by: David Daney <david.daney@cavium.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Cc: linux-mips@linux-mips.org
Cc: devicetree-discuss@lists.ozlabs.org
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: linux-kernel@vger.kernel.org
Cc: David Daney <david.daney@cavium.com>
Patchwork: https://patchwork.linux-mips.org/patch/3942/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2012-07-23 13:54:53 +01:00
David Daney
368bec0d4a netdev: octeon_mgmt: Convert to use device tree.
The device tree will supply the register bank base addresses, make
register addressing relative to those.  PHY connection is now
described by the device tree.

The OCTEON_IRQ_MII{0,1} symbols are also removed as they are now
unused and interfere with the irq_domain used for device tree irq
mapping.

Signed-off-by: David Daney <david.daney@cavium.com>
Acked-by: David S. Miller <davem@davemloft.net>
Cc: linux-mips@linux-mips.org
Cc: devicetree-discuss@lists.ozlabs.org
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/3941/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2012-07-23 13:54:53 +01:00
David Daney
2fd46f47be netdev: mdio-octeon.c: Convert to use device tree.
Get the MDIO bus controller addresses from the device tree, small
clean up in use of devm_*

Remove, now unused, platform device setup code.

Signed-off-by: David Daney <david.daney@cavium.com>
Acked-by: David S. Miller <davem@davemloft.net>
Cc: linux-mips@linux-mips.org
Cc: devicetree-discuss@lists.ozlabs.org
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/3938/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2012-07-23 13:54:53 +01:00
David Daney
f353a218de i2c: Convert i2c-octeon.c to use device tree.
There are three parts to this:

1) Remove the definitions of OCTEON_IRQ_TWSI and OCTEON_IRQ_TWSI2.
   The interrupts are specified by the device tree and these hard
   coded irq numbers block the used of the irq lines by the irq_domain
   code.

2) Remove platform device setup code from octeon-platform.c, it is
   now unused.

3) Convert i2c-octeon.c to use device tree.  Part of this includes
   using the devm_* functions instead of the raw counterparts, thus
   simplifying error handling.  No functionality is changed.

Signed-off-by: David Daney <david.daney@cavium.com>
Acked-by: Rob Herring <rob.herring@calxeda.com>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
Cc: linux-mips@linux-mips.org
Cc: devicetree-discuss@lists.ozlabs.org
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/3939/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2012-07-23 13:54:53 +01:00
David Daney
a0c16582b5 MIPS: Octeon: Setup irq_domains for interrupts.
Create two domains.  One for the GPIO lines, and the other for on-chip
sources.

Signed-off-by: David Daney <david.daney@cavium.com>
Cc: linux-mips@linux-mips.org
Cc: devicetree-discuss@lists.ozlabs.org
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: linux-kernel@vger.kernel.org
Cc: David Daney <david.daney@cavium.com>
Patchwork: https://patchwork.linux-mips.org/patch/3936/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2012-07-23 13:54:53 +01:00
David Daney
7ed1815296 MIPS: Octeon: Initialize and fixup device tree.
If a compiled in device tree template is used, trim out unwanted parts
based on legacy platform probing.

Signed-off-by: David Daney <david.daney@cavium.com>
Cc: linux-mips@linux-mips.org
Cc: devicetree-discuss@lists.ozlabs.org
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: linux-kernel@vger.kernel.org
Cc: David Daney <david.daney@cavium.com>
Patchwork: https://patchwork.linux-mips.org/patch/3935/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2012-07-23 13:54:52 +01:00
David Daney
736b1c9c95 MIPS: Octeon: Add device tree source files.
The two device tree files octeon_3xxx.dts and octeon_68xx.dts are
trimmed by code in a subsequent patch to reflect the hardware actually
present on the board.  To this end several properties that are not
part of the declared bindings are added to aid in trimming off
unwanted nodes.  Since the device tree and the code that trims it are
bound into the kernel binary, these 'marker' properties never escape
into the wild, and are purely an implementation detail of the kernel
early boot process.  This is done for backwards compatibility with
existing boards (identified by a board type enumeration value by their
bootloaders).  New boards will always pass a device tree from the
bootloader, the built-in trees are ignored in this case.

Signed-off-by: David Daney <david.daney@cavium.com>
Cc: linux-mips@linux-mips.org
Cc: devicetree-discuss@lists.ozlabs.org
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: linux-kernel@vger.kernel.org
Cc: David Daney <david.daney@cavium.com>
Patchwork: https://patchwork.linux-mips.org/patch/3937/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2012-07-23 13:54:52 +01:00
David Daney
a339aef904 MIPS: OCTEON: Consolidate the edge and level irq_chip structures.
We can consolidate octeon_irq_chip_ciu_edge and octeon_irq_chip_ciu as
they only differ in the .irq_ack element, and that is unused by the
level handler.  This gets rid of a bunch of duplicate definitions.

Signed-off-by: David Daney <david.daney@cavium.com>
Cc:  linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/3931/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2012-07-23 13:54:52 +01:00
David Daney
f5e0828421 MIPS: OCTEON: Remove unneeded OCTEON_IRQ_* defines.
The follow-on patch to add irq_domain support will be the supported
method for using these irq lines, so get these defines out of the way
in preperation for that.

Signed-off-by: David Daney <david.daney@cavium.com>
Cc:  linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/3930/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2012-07-23 13:54:52 +01:00
David Daney
6d1ab4c22d MIPS: Octeon: Add irq handlers for GPIO interrupts.
This is needed for follow-on on patches for Octeon to use the Device
Tree to configure GPIO interrupts.

Signed-off-by: David Daney <david.daney@cavium.com>
Cc:  linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/3932/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2012-07-23 13:54:51 +01:00
David Daney
05b8c8c128 MIPS: OCTEON: Remove some unused files.
These FPA related files are not used anywhere in the kernel.  Remove
them.

Signed-off-by: David Daney <david.daney@cavium.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/3892/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2012-07-23 13:54:51 +01:00