As per "Table 26-7. SATA PHY Subsystem Low-Level Programming Sequence"
in TRM [1] we need to turn on SATA_PHY_TX before SATA_PHY_RX.
[1] DRA75x, DRA74x TRM - http://www.ti.com/lit/ug/sprui30f/sprui30f.pdf
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
For increased DPLL stability use the settings recommended in
the TRM [1] for PHY_RX registers for SATA and USB.
For SATA we need to use spread spectrum settings even
though we don't have spread spectrum enabled. The
suggested non-spread spectrum settings don't work.
[1] DRA75x, DRA74x TRM - http://www.ti.com/lit/ug/sprui30f/sprui30f.pdf
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Introduce a mode property in the driver data so that
we don't have to keep using "of_device_is_compatible()"
throughtout the driver.
No functional change.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
There seems to be a missing bit-wise or operator when setting val,
fix this by adding it in.
Fixes: 2796ceb0c1 ("phy: ti-pipe3: Update pcie phy settings")
Cc: stable@vger.kernel.org # v4.19+
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Add UFS M-PHY node document for MediaTek SoC chips.
Signed-off-by: Stanley Chu <stanley.chu@mediatek.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
This patch documents the new proprty drive-impedance-ohm for
Rockchip's eMMC PHY node.
Signed-off-by: Christoph Muellner <christoph.muellner@theobroma-systems.com>
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
The rockchip-emmc PHY can be configured with different
drive impedance values. Currenlty a value of 50 Ohm is
hard coded into the driver.
This patch introduces the DTS property 'drive-impedance-ohm'
for the rockchip-emmc phy node, which uses the value from the DTS
to setup the drive impedance accordingly.
Signed-off-by: Christoph Muellner <christoph.muellner@theobroma-systems.com>
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
The phy code was using implicit sequencing between the PHY driver
and the UFS driver to implement certain hardware requirements.
Specifically, the PHY reset register in the UFS controller needs
to be deasserted before serdes start occurs in the PHY.
Before this change, the code was doing this by utilizing the two
phy callbacks, phy_init() and phy_poweron(), as "init step 1" and
"init step 2", where the UFS driver would deassert reset between
these two steps.
This makes it challenging to power off the regulators in suspend,
as regulators are initialized in init, not in poweron(), but only
poweroff() is called during suspend, not exit().
For UFS, move the actual firing up of the PHY to phy_poweron() and
phy_poweroff() callbacks, rather than init()/exit(). UFS calls
phy_poweroff() during suspend, so now all clocks and regulators for
the phy can be powered down during suspend.
QMP is a little tricky because the PHY is also shared with PCIe and
USB3, which have their own definitions for init() and poweron(). Rename
the meaty functions to _enable() and _disable() to disentangle from the
PHY core names, and then create two different ops structures: one for
UFS and one for the other PHY types.
In phy-qcom-ufs, remove the 'is_powered_on' and 'is_started' guards,
as the generic PHY code does the reference counting. The
14/20nm-specific init functions get collapsed into the generic power_on()
function, with the addition of a calibrate() callback specific to 14/20nm.
Signed-off-by: Evan Green <evgreen@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Move the PHY reset from ufs-qcom into the respective PHYs. This will
allow us to merge the two phases of UFS PHY initialization.
Signed-off-by: Evan Green <evgreen@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Expose a reset controller that the phy will later use to control its
own PHY reset in the UFS controller. This will enable the combining
of PHY init functionality into a single function.
Signed-off-by: Evan Green <evgreen@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Add a resets property to the PHY that represents the PHY reset
register in the UFS controller itself. This better describes the
complete specification of the PHY, and allows the PHY to perform
its initialization in a single function, rather than relying on
back-channel sequencing of initialization through the PHY framework.
Signed-off-by: Evan Green <evgreen@chromium.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Add a required reset to the SDM845 UFS phy to express the PHY reset
bit inside the UFS controller register space. Before this change, this
reset was not expressed in the DT, and the driver utilized two different
callbacks (phy_init and phy_poweron) to implement a two-phase
initialization procedure that involved deasserting this reset between
init and poweron. This abused the two callbacks and diluted their
purpose.
That scheme does not work as regulators cannot be turned off in
phy_poweroff because they were turned on in init, rather than poweron.
The net result is that regulators are left on in suspend that shouldn't
be.
This new scheme gives the UFS reset to the PHY, so that it can fully
initialize itself in a single callback. We can then turn regulators on
during poweron and off during poweroff.
Signed-off-by: Evan Green <evgreen@chromium.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Enable Qualcomm UFS controllers to expose the PHY reset via a reset
controller.
Signed-off-by: Evan Green <evgreen@chromium.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
This adds support for the shared USB3 + PCIE PHY found in the
Amlogic G12A SoC Family.
It supports USB3 Host mode or PCIE 2.0 mode, depending on the layout of
the board.
Selection is done by the #phy-cells, making the mode static and exclusive.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
This adds support for the USB2 PHY found in the Amlogic G12A SoC Family.
It supports Host and/or Peripheral mode, depending on it's position.
The first PHY is only used as Host, but the second supports Dual modes
defined by the USB Control Glue HW in front of the USB Controllers.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Add the Amlogic G12A Family USB3 + PCIE Combo PHY Bindings.
This PHY can provide exclusively USB3 or PCIE support on shared I/Os.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Add the Amlogic G12A Family USB2 OTG PHY Bindings
The PHY can work in host or peripheral modes depending on it's position.
Configuration of the mode is part of the USBCTRL registers which are
outside of the PHY registers.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
USB PHY driver supports two types of stingray USB PHYs
- Type 1 is a combo PHY contains two PHYs, one SS and one HS.
- Type 2 is a single HS PHY.
These two PHY versons support both Generic xHCI host controller driver
and BDC Broadcom device controller driver.
Signed-off-by: Srinath Mannam <srinath.mannam@broadcom.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Add DT binding document for Stingray USB PHY.
Signed-off-by: Srinath Mannam <srinath.mannam@broadcom.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Add support for the XUSB pad controller found on Tegra186 SoCs. It is
mostly similar to the same IP found on earlier chips, but the number of
pads exposed differs, as do the programming sequences.
Note that the DVDD_PEX, DVDD_PEX_PLL, HVDD_PEX and HVDD_PEX_PLL power
supplies of the XUSB pad controller require strict power sequencing and
are therefore controlled by the PMIC on Tegra186.
Signed-off-by: JC Kuo <jckuo@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
[dan.carpenter@oracle.com: Fix testing the wrong variable in probe()]
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
[yuehaibing@huawei.com: Make two functions static to fix sparse warning]
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Support enabling various supplies needed to provide power to the PLLs
and logic used to drive the USB, PCI and SATA pads.
Reviewed-by: JC Kuo <jckuo@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
The device tree bindings document the "mode" property of "ports"
subnodes, but the driver was not parsing the property. In preparation
for adding role switching, parse the property at probe time.
Based on work by JC Kuo <jckuo@nvidia.com>.
Reviewed-by: JC Kuo <jckuo@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Tegra186 USB2 pads and USB3 pads do not have hardware mux for changing
the pad function. For such "lanes", we can skip the lane mux register
programming.
Signed-off-by: JC Kuo <jckuo@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Extend the bindings to cover the set of features found in Tegra186. Note
that, technically, there are four more supplies connected to the XUSB
pad controller (DVDD_PEX, DVDD_PEX_PLL, HVDD_PEX and HVDD_PEX_PLL), but
the power sequencing requirements of Tegra186 require these to be under
the control of the PMIC.
Reviewed-by: JC Kuo <jckuo@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
The USB subsystem has always had an unusual requirement for its
scatter-gather transfers: Each element in the scatterlist (except the
last one) must have a length divisible by the bulk maxpacket size.
This is a particular issue for USB mass storage, which uses SG lists
created by the block layer rather than setting up its own.
So far we have scraped by okay because most devices have a logical
block size of 512 bytes or larger, and the bulk maxpacket sizes for
USB 2 and below are all <= 512. However, USB 3 has a bulk maxpacket
size of 1024. Since the xhci-hcd driver includes native SG support,
this hasn't mattered much. But now people are trying to use USB-3
mass storage devices with USBIP, and the vhci-hcd driver currently
does not have full SG support.
The result is an overflow error, when the driver attempts to implement
an SG transfer of 63 512-byte blocks as a single
3584-byte (7 blocks) transfer followed by seven 4096-byte (8 blocks)
transfers. The device instead sends 31 1024-byte packets followed by
a 512-byte packet, and this overruns the first SG buffer.
Ideally this would be fixed by adding better SG support to vhci-hcd.
But for now it appears we can work around the problem by
asking the block layer to respect the maxpacket limitation, through
the use of the virt_boundary_mask.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Seth Bollinger <Seth.Bollinger@digi.com>
Tested-by: Seth Bollinger <Seth.Bollinger@digi.com>
CC: Ming Lei <tom.leiming@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The generic EHCI binding is used by many controllers that are using the
EHCI spec.
Convert that binding to a YAML description to enable the validation on all
the nodes using that binding.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The generic OHCI binding is used by many controllers that are using the
OHCI spec.
Convert that binding to a YAML description to enable the validation on all
the nodes using that binding.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The USB HCD generic binding is used by many USB host bindings.
In order to allow the DT validation to happen on those, let's create a YAML
description for that generic binding that can be referenced later on.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The returned value in status has never been used since
commit 4296c70a5e ("USB/xHCI: Enable USB 3.0 hub remote wakeup.")
So remove 'status' completely.
Remove warning (W=1):
drivers/usb/core/hub.c:3671:8: warning: variable 'status' set but not used [-Wunused-but-set-variable]
Signed-off-by: Mathieu Malaterre <malat@debian.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Convert USB documents to ReST, in order to prepare for adding it
to the kernel API book, as most of the stuff there are driver or
subsystem-related.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This commit adds Tegra186 XUSB host mode controller support. This is
very similar to the existing support for Tegra124 and Tegra210, except
that the number of ports and PHYs differs and the IPFS wrapper being
gone.
Signed-off-by: JC Kuo <jckuo@nvidia.com>
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Starting with Tegra186, the XUSB controller no longer has the IPFS
wrapper. This commit adds a "has_ipfs" field to struct tegra_xusb_soc
that can be used to declare the existence of the IPFS wrapper.
For the existing chips (i.e. Tegra124 and Tegra210), the new field is
set to true. A future patch adding support for Tegra186 will set it to
false.
Signed-off-by: JC Kuo <jckuo@nvidia.com>
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Extend the bindings to cover the set of features found in Tegra186.
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: JC Kuo <jckuo@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On top of this, a cleanup of kvm_para.h headers, which were exported by
some architectures even though they not support KVM at all. This is
responsible for all the Kbuild changes in the diffstat.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iQEcBAABAgAGBQJcoM5VAAoJEL/70l94x66DU3EH/A8sYdsfeqALWElm2Sy9TYas
mntz+oTWsl3vDy8s8zp1ET2NpF7oBlBEMmCWhVEJaD+1qW3VpTRAseR3Zr9ML9xD
k+BQM8SKv47o86ZN+y4XALl30Ckb3DXh/X1xsrV5hF6J3ofC+Ce2tF560l8C9ygC
WyHDxwNHMWVA/6TyW3mhunzuVKgZ/JND9+0zlyY1LKmUQ0BQLle23gseIhhI0YDm
B4VGIYU2Mf8jCH5Ir3N/rQ8pLdo8U7f5P/MMfgXQafksvUHJBg6B6vOhLJh94dLh
J2wixYp1zlT0drBBkvJ0jPZ75skooWWj0o3otEA7GNk/hRj6MTllgfL5SajTHZg=
=/A7u
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull KVM fixes from Paolo Bonzini:
"A collection of x86 and ARM bugfixes, and some improvements to
documentation.
On top of this, a cleanup of kvm_para.h headers, which were exported
by some architectures even though they not support KVM at all. This is
responsible for all the Kbuild changes in the diffstat"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (28 commits)
Documentation: kvm: clarify KVM_SET_USER_MEMORY_REGION
KVM: doc: Document the life cycle of a VM and its resources
KVM: selftests: complete IO before migrating guest state
KVM: selftests: disable stack protector for all KVM tests
KVM: selftests: explicitly disable PIE for tests
KVM: selftests: assert on exit reason in CR4/cpuid sync test
KVM: x86: update %rip after emulating IO
x86/kvm/hyper-v: avoid spurious pending stimer on vCPU init
kvm/x86: Move MSR_IA32_ARCH_CAPABILITIES to array emulated_msrs
KVM: x86: Emulate MSR_IA32_ARCH_CAPABILITIES on AMD hosts
kvm: don't redefine flags as something else
kvm: mmu: Used range based flushing in slot_handle_level_range
KVM: export <linux/kvm_para.h> and <asm/kvm_para.h> iif KVM is supported
KVM: x86: remove check on nr_mmu_pages in kvm_arch_commit_memory_region()
kvm: nVMX: Add a vmentry check for HOST_SYSENTER_ESP and HOST_SYSENTER_EIP fields
KVM: SVM: Workaround errata#1096 (insn_len maybe zero on SMAP violation)
KVM: Reject device ioctls from processes other than the VM's creator
KVM: doc: Fix incorrect word ordering regarding supported use of APIs
KVM: x86: fix handling of role.cr4_pae and rename it to 'gpte_size'
KVM: nVMX: Do not inherit quadrant and invalid for the root shadow EPT
...
Pull x86 fixes from Thomas Gleixner:
"A pile of x86 updates:
- Prevent exceeding he valid physical address space in the /dev/mem
limit checks.
- Move all header content inside the header guard to prevent compile
failures.
- Fix the bogus __percpu annotation in this_cpu_has() which makes
sparse very noisy.
- Disable switch jump tables completely when retpolines are enabled.
- Prevent leaking the trampoline address"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/realmode: Make set_real_mode_mem() static inline
x86/cpufeature: Fix __percpu annotation in this_cpu_has()
x86/mm: Don't exceed the valid physical address space
x86/retpolines: Disable switch jump tables when retpolines are enabled
x86/realmode: Don't leak the trampoline kernel address
x86/boot: Fix incorrect ifdeffery scope
x86/resctrl: Remove unused variable
Pull perf tooling fixes from Thomas Gleixner:
"Core libraries:
- Fix max perf_event_attr.precise_ip detection.
- Fix parser error for uncore event alias
- Fixup ordering of kernel maps after obtaining the main kernel map
address.
Intel PT:
- Fix TSC slip where A TSC packet can slip past MTC packets so that
the timestamp appears to go backwards.
- Fixes for exported-sql-viewer GUI conversion to python3.
ARM coresight:
- Fix the build by adding a missing case value for enumeration value
introduced in newer library, that now is the required one.
tool headers:
- Syncronize kernel headers with the kernel, getting new io_uring and
pidfd_send_signal syscalls so that 'perf trace' can handle them"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf pmu: Fix parser error for uncore event alias
perf scripts python: exported-sql-viewer.py: Fix python3 support
perf scripts python: exported-sql-viewer.py: Fix never-ending loop
perf machine: Update kernel map address and re-order properly
tools headers uapi: Sync powerpc's asm/kvm.h copy with the kernel sources
tools headers: Update x86's syscall_64.tbl and uapi/asm-generic/unistd
tools headers uapi: Update drm/i915_drm.h
tools arch x86: Sync asm/cpufeatures.h with the kernel sources
tools headers uapi: Sync linux/fcntl.h to get the F_SEAL_FUTURE_WRITE addition
tools headers uapi: Sync asm-generic/mman-common.h and linux/mman.h
perf evsel: Fix max perf_event_attr.precise_ip detection
perf intel-pt: Fix TSC slip
perf cs-etm: Add missing case value
Pull CPU hotplug fixes from Thomas Gleixner:
"Two SMT/hotplug related fixes:
- Prevent crash when HOTPLUG_CPU is disabled and the CPU bringup
aborts. This is triggered with the 'nosmt' command line option, but
can happen by any abort condition. As the real unplug code is not
compiled in, prevent the fail by keeping the CPU in zombie state.
- Enforce HOTPLUG_CPU for SMP on x86 to avoid the above situation
completely. With 'nosmt' being a popular option it's required to
unplug the half brought up sibling CPUs (due to the MCE wreckage)
completely"
* 'smp-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/smp: Enforce CONFIG_HOTPLUG_CPU when SMP=y
cpu/hotplug: Prevent crash when CPU bringup fails on CONFIG_HOTPLUG_CPU=n
Pull locking fixlet from Thomas Gleixner:
"Trivial update to the maintainers file"
* 'locking-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
MAINTAINERS: Remove deleted file from futex file pattern
Pull core fixes from Thomas Gleixner:
"A small set of core updates:
- Make the watchdog respect the selected CPU mask again. That was
broken by the rework of the watchdog thread management and caused
inconsistent state and NMI watchdog being unstoppable.
- Ensure that the objtool build can find the libelf location.
- Remove dead kcore stub code"
* 'core-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
watchdog: Respect watchdog cpumask on CPU hotplug
objtool: Query pkg-config for libelf location
proc/kcore: Remove unused kclist_add_remap()
Three non-regression fixes.
Our optimised memcmp could read past the end of one of the buffers and
potentially trigger a page fault leading to an oops.
Some of our code to read energy management data on PowerVM had an endian bug
leading to bogus results.
When reporting a machine check exception we incorrectly reported TLB multihits
as D-Cache multhits due to a missing entry in the array of causes.
Thanks to:
Chandan Rajendra, Gautham R. Shenoy, Mahesh Salgaonkar, Segher Boessenkool,
Vaidyanathan Srinivasan.
-----BEGIN PGP SIGNATURE-----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=Ugv6
-----END PGP SIGNATURE-----
Merge tag 'powerpc-5.1-4' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc fixes from Michael Ellerman:
"Three non-regression fixes.
- Our optimised memcmp could read past the end of one of the buffers
and potentially trigger a page fault leading to an oops.
- Some of our code to read energy management data on PowerVM had an
endian bug leading to bogus results.
- When reporting a machine check exception we incorrectly reported
TLB multihits as D-Cache multhits due to a missing entry in the
array of causes.
Thanks to: Chandan Rajendra, Gautham R. Shenoy, Mahesh Salgaonkar,
Segher Boessenkool, Vaidyanathan Srinivasan"
* tag 'powerpc-5.1-4' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc/pseries/mce: Fix misleading print for TLB mutlihit
powerpc/pseries/energy: Use OF accessor functions to read ibm,drc-indexes
powerpc/64: Fix memcmp reading past the end of src/dest
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQQUwxxKyE5l/npt8ARiEGxRG/Sl2wUCXJ+ymAAKCRBiEGxRG/Sl
2yIKAQCnxxzaaCfoXtnYnpgtSZApKX+ifpkImh1WOvly+HLE4QEA3i3Bg4pb23ck
fClCFU9sahuxJbakWD0pvs4k77I1GQY=
=5KCa
-----END PGP SIGNATURE-----
Merge tag 'led-fixes-for-5.1-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/j.anaszewski/linux-leds
Pull LED fixes from Jacek Anaszewski:
- fix refcnt leak on interface rename
- use memcpy in device_name_store() to avoid including garbage from a
previous, longer value in the device_name
- fix a potential NULL pointer dereference in case of_match_device()
cannot find a match
* tag 'led-fixes-for-5.1-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/j.anaszewski/linux-leds:
leds: trigger: netdev: use memcpy in device_name_store
leds: pca9532: fix a potential NULL pointer dereference
leds: trigger: netdev: fix refcnt leak on interface rename
- Revert the extended use of gpio_set_config() and think about
how we can do this properly.
- Fix up the SPI CS GPIO handling so it now works properly on
the SPI bus children, as intended.
- Error paths and driver fixes.
-----BEGIN PGP SIGNATURE-----
iQIcBAABAgAGBQJcn4QVAAoJEEEQszewGV1zhyMP/3E2PeJmi1IKK2YTGJaEdz0+
71Q6++a7xB1jTOa1FKgYBUI+cwjjyhpaFU8Ax7jbNEpcUgTRu+wKFrdAp2of7UZk
iv+7ODzw+d/usdhlLgFSIf+NHUFSytQBZRRS4sSFi2QyavHF49pXzWv2oMFOgGiv
sn/Ke2lU8oT49W1TfH/RjLTyx36eEBhEyWe9JKYCrFuDFCYvykAOmYPP6wULHRG5
UCsRCP/tYktu5aANAavMh+o0SRH6Xik23bPo5adP32iKb4HuKurxy5bl26k+T5tU
crRANm/LD/3fu2GBoKPl3EjI7zQsJINwwvYO65tX44WJpBVZX07MRBiBCZxAex/m
j11x5oA9pBNM8Jn2MP2IIP3+izpyc3ojwJoLn27fM/PizMS3vU4Wp7MetAAjCwmb
qF7Y2ua3IGHn4vay5u4UJjGP/wFptv8YJLlqCO1wkeH2LdJm6ZM3uAhj0R4VOPoA
bTmFSRVCGOVL1DYYW2eWxADXW5zmdXmuKQx+/bmMUiw1s84gDOde8Yg7UGegaT4k
H1FjacvwKU0Q/OMx+4+jv1h6yAb0tF4iTkno5v99WEOAg+WWNnHj85r6aigaWSa7
FVmsMEJbDJbvUF1rEZ9Zq1fmwBKOY3qd3zSRulchimx0wd3LeBw3AKLx8ojk2/Hq
hoLlO5f2ifYTuHQbnHnX
=6ndO
-----END PGP SIGNATURE-----
Merge tag 'gpio-v5.1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO fixes from Linus Walleij:
"As you can see [in the git history] I was away on leave and Bartosz
kindly stepped in and collected a slew of fixes, I pulled them into my
tree in two sets and merged some two more fixes (fixing my own caused
bugs) on top.
Summary:
- Revert the extended use of gpio_set_config() and think about how we
can do this properly.
- Fix up the SPI CS GPIO handling so it now works properly on the SPI
bus children, as intended.
- Error paths and driver fixes"
* tag 'gpio-v5.1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio:
gpio: mockup: use simple_read_from_buffer() in debugfs read callback
gpio: of: Fix of_gpiochip_add() error path
gpio: of: Check for "spi-cs-high" in child instead of parent node
gpio: of: Check propname before applying "cs-gpios" quirks
gpio: mockup: fix debugfs read
Revert "gpio: use new gpio_set_config() helper in more places"
gpio: aspeed: fix a potential NULL pointer dereference
gpio: amd-fch: Fix bogus SPDX identifier
gpio: adnp: Fix testing wrong value in adnp_gpio_direction_input
gpio: exar: add a check for the return value of ida_simple_get fails
If userspace doesn't end the input with a newline (which can easily
happen if the write happens from a C program that does write(fd,
iface, strlen(iface))), we may end up including garbage from a
previous, longer value in the device_name. For example
# cat device_name
# printf 'eth12' > device_name
# cat device_name
eth12
# printf 'eth3' > device_name
# cat device_name
eth32
I highly doubt anybody is relying on this behaviour, so switch to
simply copying the bytes (we've already checked that size is <
IFNAMSIZ) and unconditionally zero-terminate it; of course, we also
still have to strip a trailing newline.
This is also preparation for future patches.
Fixes: 06f502f57d ("leds: trigger: Introduce a NETDEV trigger")
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
In case of_match_device cannot find a match, return -EINVAL to avoid
NULL pointer dereference.
Fixes: fa4191a609 ("leds: pca9532: Add device tree support")
Signed-off-by: Kangjie Lu <kjlu@umn.edu>
Signed-off-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
Here are some small staging driver fixes for 5.1-rc3, and one driver
removal.
The biggest thing here is the removal of the mt7621-eth driver as a
"real" network driver was merged in 5.1-rc1 for this hardware, so this
old driver can now be removed.
Other than that, there are just a number of small fixes, all resolving
reported issues and some potential corner cases for error handling
paths.
All of these have been in linux-next with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXJ8vpg8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+yksHgCeJATLFpgiWqGvR8K/PfiG2QixudEAoMivMAM2
s1Obj1TFIQK+xTAINt6U
=uJaK
-----END PGP SIGNATURE-----
Merge tag 'staging-5.1-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging driver fixes from Greg KH:
"Here are some small staging driver fixes for 5.1-rc3, and one driver
removal.
The biggest thing here is the removal of the mt7621-eth driver as a
"real" network driver was merged in 5.1-rc1 for this hardware, so this
old driver can now be removed.
Other than that, there are just a number of small fixes, all resolving
reported issues and some potential corner cases for error handling
paths.
All of these have been in linux-next with no reported issues"
* tag 'staging-5.1-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
staging: vt6655: Remove vif check from vnt_interrupt
staging: erofs: keep corrupted fs from crashing kernel in erofs_readdir()
staging: octeon-ethernet: fix incorrect PHY mode
staging: vc04_services: Fix an error code in vchiq_probe()
staging: erofs: fix error handling when failed to read compresssed data
staging: vt6655: Fix interrupt race condition on device start up.
staging: rtlwifi: Fix potential NULL pointer dereference of kzalloc
staging: rtl8712: uninitialized memory in read_bbreg_hdl()
staging: rtlwifi: rtl8822b: fix to avoid potential NULL pointer dereference
staging: rtl8188eu: Fix potential NULL pointer dereference of kcalloc
staging, mt7621-pci: fix build without pci support
staging: speakup_soft: Fix alternate speech with other synths
staging: axis-fifo: add CONFIG_OF dependency
staging: olpc_dcon_xo_1: add missing 'const' qualifier
staging: comedi: ni_mio_common: Fix divide-by-zero for DIO cmdtest
staging: erofs: fix to handle error path of erofs_vmap()
staging: mt7621-dts: update ethernet settings.
staging: remove mt7621-eth
Here are some small tty and serial driver fixes for 5.1-rc3.
Nothing major here, just a number of potential problems fixes for error
handling paths, as well as some other minor bugfixes for reported issues
with 5.1-rc1.
All of these have been in linux-next with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXJ8wCg8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ylWigCfSPVnxuGsNFTZIN8CUMBH4I5cmjkAnjrN3NdS
Sumt55mskpi/Ht+5UWmw
=LFqo
-----END PGP SIGNATURE-----
Merge tag 'tty-5.1-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial fixes from Greg KH:
"Here are some small tty and serial driver fixes for 5.1-rc3.
Nothing major here, just a number of potential problems fixes for
error handling paths, as well as some other minor bugfixes for
reported issues with 5.1-rc1.
All of these have been in linux-next with no reported issues"
* tag 'tty-5.1-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
tty: fix NULL pointer issue when tty_port ops is not set
Disable kgdboc failed by echo space to /sys/module/kgdboc/parameters/kgdboc
dt-bindings: serial: Add compatible for Mediatek MT8183
tty/serial: atmel: RS485 HD w/DMA: enable RX after TX is stopped
tty/serial: atmel: Add is_half_duplex helper
serial: sh-sci: Fix setting SCSCR_TIE while transferring data
serial: ar933x_uart: Fix build failure with disabled console
tty: serial: qcom_geni_serial: Initialize baud in qcom_geni_console_setup
sc16is7xx: missing unregister/delete driver on error in sc16is7xx_init()
tty: mxs-auart: fix a potential NULL pointer dereference
tty: atmel_serial: fix a potential NULL pointer dereference
serial: max310x: Fix to avoid potential NULL pointer dereference
serial: mvebu-uart: Fix to avoid a potential NULL pointer dereference
