The patches received from the vendor contained a lot of CodingStyle
issues. Cleans the style issues reported by checkpatch.pl on
those drivers.
It is better to do such style fixes when merging a big set of
changes than latter. Of course, the better is to receive patches
already cleaned ;)
Acked-by: Sri Deevi <Srinivasa.Deevi@conexant.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Improves the logic, for it to be clearer and to avoid having
board-dependent config there.
Acked-by: Sri Deevi <Srinivasa.Deevi@conexant.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The driver has a field to indicate what bus is used by tuner and
by demod. However, this field were never used. On Pixelview,
it uses I2C 2 for tuner, instead of I2C 1.
drivers/media/video/cx231xx/cx231xx-cards.c
Acked-by: Sri Deevi <Srinivasa.Deevi@conexant.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
drivers/media/video/cx231xx/cx231xx-avcore.c:1608: warning: format ‘%d’ expects type ‘int’, but argument 3 has type ‘long unsigned int’
drivers/media/video/cx231xx/cx231xx-417.c:1047: warning: format ‘%d’ expects type ‘int’, but argument 3 has type ‘size_t’
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Adjust the vblank and vactive counts so that they don't throw an error in
cx25840's set_std call (we did an equivalent change for NTSC when we got the
scaler working).
Signed-off-by: Devin Heitmueller <dheitmueller@hauppauge.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The cx231xx_do_mode_ctrl_overrides() function was not touching the vactive line
count for PAL/SECAM modes, which in some use cases results in it being left in
the chip default state of 480 (NTSC).
Explicitly set the values, as is already done for NTSC.
Signed-off-by: Devin Heitmueller <dheitmueller@hauppauge.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fix some indentation problems and remove an "if (1)" from the Colibri setup
function.
Signed-off-by: Devin Heitmueller <dheitmueller@hauppauge.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The cx231xx_set_Colibri_For_LowIF() function is only ever called if the tuner
has a DIF (see vidioc_s_frequency() in cx231xx-video.c). Hence, we do not
need to do a board specific check in this function.
Signed-off-by: Devin Heitmueller <dheitmueller@hauppauge.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The current code was deciding whether a DIF was present based on the board
profile. However, this is just another thing for someone to get wrong when
adding new boards. Make the decision based on the tuner instead, so that a
developer adding new boards only needs to specify which tuner the device has.
Of course, the first time somebody adds a board with a tuner other than xc5000
or tda18271, he/she will need to add another line for that tuner. But we
provide a friendly message in dmesg to let them know that.
Signed-off-by: Devin Heitmueller <dheitmueller@hauppauge.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Nobody is ever going to implement an i2c based IR controller on a bridge that
has an onboard universal IR receiver. This stuff was all copied from em28xx,
which has old enough versions of the chip that some didn't have onboard IR.
Remove the stubs related to i2c based IR (keeping the cx231xx-input code).
Signed-off-by: Devin Heitmueller <dheitmueller@hauppauge.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Move a printk() message which refers to enabling the cx23417 so that it only
shows up on a board that has the cx23417.
Signed-off-by: Devin Heitmueller <dheitmueller@hauppauge.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The video grabber reference design (Veyron) does not have a tuner input, so
do not have it defined in the board profile.
Signed-off-by: Devin Heitmueller <dheitmueller@hauppauge.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Extend the board profile structure to allow configuration of the output mode.
Right now they are all doing VIP 1.1 format, but we have a board that needs
ITU656 format (which hasn't been checked in yet).
Signed-off-by: Devin Heitmueller <dheitmueller@hauppauge.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add initial support for the Hauppauge USBLive 2 (2040:c200). Note that I
had to copy a bunch of the case statements used for the Conexant video grabber
reference design (which also doesn't have a tuner). This will likely need to
be refactored out into the board profile.
Signed-off-by: Devin Heitmueller <dheitmueller@hauppauge.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The tuner is on i2c port 3 just like all the reference designs. Having it
improperly set to port #1 causes the tuner initialization to fail when enabling
the device.
Signed-off-by: Devin Heitmueller <dheitmueller@hauppauge.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
If switching to a tuner input, reset the standard and tune to the last known
frequency. We need to do this in particular for this bridge since the tuner
gets powered down when captuing on the composite or s-video inputs.
Signed-off-by: Devin Heitmueller <dheitmueller@hauppauge.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Remove a hack which was jammed into s_input to force the device into bulk mode
at runtime (an abuse of the API). If this sort of functionality is actually
needed (aside from the existing "transfer_mode" modprobe variable), a patch
can be submitted which makes use of a private control.
Signed-off-by: Devin Heitmueller <dheitmueller@hauppauge.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The Exeter hardware design does not use GPIOs to manage whether its in
digital mode or analog mode, but we need to setup the power control properly.
For that board, setup power control and remove the mux select call. It is
highly likely that this change could be used by other boards as well, which
would make power management cleaner (fixing known issues transitioning between
analog and digital mode).
Signed-off-by: Devin Heitmueller <dheitmueller@hauppauge.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
You cannot call the video_mux routine from within the isoc setup, because that
code is shared with the digital isoc handler. This was causing the GPIOs and
power control to be put into the wrong state when starting up digital mode.
Signed-off-by: Devin Heitmueller <dheitmueller@hauppauge.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
We need to clear out the field before setting individual bits, or else we end
up with a union of whatever was there and what we are trying to set. For
example, switching to digital mode ends up being 0x30 instead of 0x10 if we
were previously in analog tv mode.
Signed-off-by: Devin Heitmueller <dheitmueller@hauppauge.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Move the responsibility for setting up the horizontal and vertical scalers
entirely to the cx25840 driver. The cx231xx-avcore was actually programming
garbage into the HSCALE_CTRL and VSCALE_CTRL registers (because of differences
in how the em28xx driver worked, which the cx231xx driver was derived from).
The net effect is that the scaler now works properly (tested with both PAL
and NTSC under mplayer and tvtime).
This patch also gets rid of cx25840 errors showing up in dmesg which say
"720x480 is not a valid size" (since we now properly setup the size of the
active video area).
Signed-off-by: Devin Heitmueller <dheitmueller@hauppauge.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Change the log level from info to debug for some log events that occur
frequently and should never need to be seen in normal operation.
Signed-off-by: Devin Heitmueller <dheitmueller@hauppauge.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
There is no need for a switch statement here. Use the contents of the board
profile to dictate the tuner driver and i2c address. Eventually if a board
ever comes around which has a different i2c bus than #1, well that should be a
field in the board profile as well.
Signed-off-by: Devin Heitmueller <dheitmueller@hauppauge.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The current code was sending one videobuf per field (despite having specified
V4L2_FIELD_SEQ_TB during setup). As a result, application which used the
read() interface would work, except they would sometimes have the fields
reversed (depending on the luck of which field the device was on when the
application started VBI capture). The net effect was that CC decoding would
only work about 50% of the time.
Restructure the VBI code a bit so that works like all the other drivers, such
that both fields are delivered in a single videobuf buffer, which ensures that
they are always received in a predictable order.
Signed-off-by: Devin Heitmueller <dheitmueller@hauppauge.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The VBI sampling rate and offset were incorrectly specified, which resulted in
CC data not being rendered under zvbi or tvtime.
Set the fields correctly.
Signed-off-by: Devin Heitmueller <dheitmueller@hauppauge.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Change a %x to a %p since the variable is a pointer
Signed-off-by: Devin Heitmueller <dheitmueller@hauppauge.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fix case where analog calls come in while the DVB side of the board is still
initializing. This patch is actually just an exact port of the same patch
made by Mauro to em28xx in hg rev 14762.
Signed-off-by: Devin Heitmueller <dheitmueller@hauppauge.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add support for various Hauppauge EXETER designs.
Note by DJH: fixed a few minor 'make checkpatch' warnings before commit.
Signed-off-by: Michael Krufky <mkrufky@kernellabs.com>
Signed-off-by: Devin Heitmueller <dheitmueller@hauppauge.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add an ext_lock argument to the videobuf init functions. This allows
drivers to pass the vdev->lock pointer (or any other externally held lock)
to videobuf. For now all drivers just pass NULL.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
As reported by Carlos, Prolink Pixelview SBTVD Hybrid is based on
Conexant cx231xx + Fujitsu 86A20S demodulator. However, both shares
the same USB ID. So, we need to use USB bcdDevice, in order to
properly discover what's the board.
We know for sure that bcd 0x100 is used for a dib0700 device, while
bcd 0x4001 is used for a cx23102 device. This patch reserves two ranges,
the first one from 0x0000-0x3f00 for dib0700, and the second from
0x4000-0x4fff for cx231xx devices.
This may need fixes in the future, as we get access to other devices.
Thanks-to: Carlos Americo Domiciano <c_domiciano@yahoo.com.br>
Cc: stable@kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
For more clearance what the functions actually do,
usb_buffer_alloc() is renamed to usb_alloc_coherent()
usb_buffer_free() is renamed to usb_free_coherent()
They should only be used in code which really needs DMA coherency.
All call sites have been changed accordingly, except for staging
drivers.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Pedro Ribeiro <pedrib@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Convert drivers/media/video/cx231xx/cx231xx-input.c to not
rely on ir-functions.c.
(I do not have the hardware so I can only compile test this)
Signed-off-by: David Härdeman <david@hardeman.nu>
Cc: Srinivasa Deevi <srinivasa.deevi@conexant.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Return -EINVAL if we don't find the control id.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
"dev" is never NULL here so there is no need to check.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
A latter patch will reuse the ir_input_register with a different meaning.
Before it, change all occurrences to a temporary name.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
card->driver is 15 characters and a NULL, the original code could
cause a buffer overflow.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Now, both driver and keytable names are exported to userspace. This
will help userspace to decide when a table need to be replaced
by another one.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files. percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.
percpu.h -> slab.h dependency is about to be removed. Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability. As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.
http://userweb.kernel.org/~tj/misc/slabh-sweep.py
The script does the followings.
* Scan files for gfp and slab usages and update includes such that
only the necessary includes are there. ie. if only gfp is used,
gfp.h, if slab is used, slab.h.
* When the script inserts a new include, it looks at the include
blocks and try to put the new include such that its order conforms
to its surrounding. It's put in the include block which contains
core kernel includes, in the same order that the rest are ordered -
alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
doesn't seem to be any matching order.
* If the script can't find a place to put a new include (mostly
because the file doesn't have fitting include block), it prints out
an error message indicating which .h file needs to be added to the
file.
The conversion was done in the following steps.
1. The initial automatic conversion of all .c files updated slightly
over 4000 files, deleting around 700 includes and adding ~480 gfp.h
and ~3000 slab.h inclusions. The script emitted errors for ~400
files.
2. Each error was manually checked. Some didn't need the inclusion,
some needed manual addition while adding it to implementation .h or
embedding .c file was more appropriate for others. This step added
inclusions to around 150 files.
3. The script was run again and the output was compared to the edits
from #2 to make sure no file was left behind.
4. Several build tests were done and a couple of problems were fixed.
e.g. lib/decompress_*.c used malloc/free() wrappers around slab
APIs requiring slab.h to be added manually.
5. The script was run on all .h files but without automatically
editing them as sprinkling gfp.h and slab.h inclusions around .h
files could easily lead to inclusion dependency hell. Most gfp.h
inclusion directives were ignored as stuff from gfp.h was usually
wildly available and often used in preprocessor macros. Each
slab.h inclusion directive was examined and added manually as
necessary.
6. percpu.h was updated not to include slab.h.
7. Build test were done on the following configurations and failures
were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my
distributed build env didn't work with gcov compiles) and a few
more options had to be turned off depending on archs to make things
build (like ipr on powerpc/64 which failed due to missing writeq).
* x86 and x86_64 UP and SMP allmodconfig and a custom test config.
* powerpc and powerpc64 SMP allmodconfig
* sparc and sparc64 SMP allmodconfig
* ia64 SMP allmodconfig
* s390 SMP allmodconfig
* alpha SMP allmodconfig
* um on x86_64 SMP allmodconfig
8. percpu.h modifications were reverted so that it could be applied as
a separate patch and serve as bisection point.
Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
