The index is received from vf, if use it directly,
an out-of-bound issue may be caused, so add a check for
this index before using it in hclge_get_rss_key().
Fixes: a638b1d8cc ("net: hns3: fix get VF RSS issue")
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The tqp_index is received from vf, if use it directly,
an out-of-bound issue may be caused, so add a check for
this tqp_index before using it in hclge_get_ring_chain_from_mbx().
Fixes: 84e095d64e ("net: hns3: Change PF to add ring-vect binding & resetQ to mailbox")
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The queue_id is received from vf, if use it directly,
an out-of-bound issue may be caused, so add a check for
this queue_id before using it in hclge_reset_vf_queue().
Fixes: 1a426f8b40 ("net: hns3: fix the VF queue reset flow error")
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are several issues which may be seen when the link goes down while
forwarding traffic, all of which can be attributed to the fact that the
port flushing procedure from the reference manual was not closely
followed.
With flow control enabled on both the ingress port and the egress port,
it may happen when a link goes down that Ethernet packets are in flight.
In flow control mode, frames are held back and not dropped. When there
is enough traffic in flight (example: iperf3 TCP), then the ingress port
might enter congestion and never exit that state. This is a problem,
because it is the egress port's link that went down, and that has caused
the inability of the ingress port to send packets to any other port.
This is solved by flushing the egress port's queues when it goes down.
There is also a problem when performing stream splitting for
IEEE 802.1CB traffic (not yet upstream, but a sort of multicast,
basically). There, if one port from the destination ports mask goes
down, splitting the stream towards the other destinations will no longer
be performed. This can be traced down to this line:
ocelot_port_writel(ocelot_port, 0, DEV_MAC_ENA_CFG);
which should have been instead, as per the reference manual:
ocelot_port_rmwl(ocelot_port, 0, DEV_MAC_ENA_CFG_RX_ENA,
DEV_MAC_ENA_CFG);
Basically only DEV_MAC_ENA_CFG_RX_ENA should be disabled, but not
DEV_MAC_ENA_CFG_TX_ENA - I don't have further insight into why that is
the case, but apparently multicasting to several ports will cause issues
if at least one of them doesn't have DEV_MAC_ENA_CFG_TX_ENA set.
I am not sure what the state of the Ocelot VSC7514 driver is, but
probably not as bad as Felix/Seville, since VSC7514 uses phylib and has
the following in ocelot_adjust_link:
if (!phydev->link)
return;
therefore the port is not really put down when the link is lost, unlike
the DSA drivers which use .phylink_mac_link_down for that.
Nonetheless, I put ocelot_port_flush() in the common ocelot.c because it
needs to access some registers from drivers/net/ethernet/mscc/ocelot_rew.h
which are not exported in include/soc/mscc/ and a bugfix patch should
probably not move headers around.
Fixes: bdeced75b1 ("net: dsa: felix: Add PCS operations for PHYLINK")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The verdict returned from ena_xdp_execute() is used to determine the
fate of the RX buffer's page. In case of XDP Redirect/TX error the
verdict should be set to XDP_ABORTED, otherwise the page won't be freed.
Fixes: a318c70ad1 ("net: ena: introduce XDP redirect implementation")
Signed-off-by: Shay Agroskin <shayagr@amazon.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Normally we clear the failover_pending flag when processing the reset.
But if we are unable to schedule a failover reset we must clear the
flag ourselves. We could fail to schedule the reset if we are in PROBING
state (eg: when booting via kexec) or because we could not allocate memory.
Thanks to Cris Forno for helping isolate the problem and for testing.
Fixes: 1d85049374 ("powerpc/vnic: Extend "failover pending" window")
Signed-off-by: Sukadev Bhattiprolu <sukadev@linux.ibm.com>
Tested-by: Cristobal Forno <cforno12@linux.ibm.com>
Link: https://lore.kernel.org/r/20210203050802.680772-1-sukadev@linux.ibm.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The XDP frame's headroom might be large enough to accommodate the
xdpf backpointer as well as shifting the data to an aligned address.
Try this first before resorting to allocating a new buffer and copying
the data.
Suggested-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Camelia Groza <camelia.groza@nxp.com>
Acked-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Acked-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The 256 byte data alignment is required for preventing DMA transaction
splits when crossing 4K page boundaries. Since XDP deals only with page
sized buffers or less, this restriction isn't needed. Instead, the data
only needs to be aligned to 64 bytes to prevent DMA transaction splits.
These lessened restrictions can increase performance by widening the pool
of permitted data alignments and preventing unnecessary realignments.
Fixes: ae680bcbd0 ("dpaa_eth: implement the A050385 erratum workaround for XDP")
Signed-off-by: Camelia Groza <camelia.groza@nxp.com>
Acked-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Acked-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When the erratum workaround is triggered, the newly created xdp_frame
structure is stored at the start of the newly allocated buffer. Avoid
the structure from being overwritten by explicitly reserving enough
space in the buffer for storing it.
Account for the fact that the structure's size might increase in time by
aligning the headroom to DPAA_FD_DATA_ALIGNMENT bytes, thus guaranteeing
the data's alignment.
Fixes: ae680bcbd0 ("dpaa_eth: implement the A050385 erratum workaround for XDP")
Signed-off-by: Camelia Groza <camelia.groza@nxp.com>
Acked-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Acked-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Michael tried to enable Advanced Error Reporting through the ENETC's
Root Complex Event Collector, and the system started spitting out single
bit correctable ECC errors coming from the ENETC interfaces:
pcieport 0000:00:1f.0: AER: Multiple Corrected error received: 0000:00:00.0
fsl_enetc 0000:00:00.0: PCIe Bus Error: severity=Corrected, type=Transaction Layer, (Receiver ID)
fsl_enetc 0000:00:00.0: device [1957:e100] error status/mask=00004000/00000000
fsl_enetc 0000:00:00.0: [14] CorrIntErr
fsl_enetc 0000:00:00.1: PCIe Bus Error: severity=Corrected, type=Transaction Layer, (Receiver ID)
fsl_enetc 0000:00:00.1: device [1957:e100] error status/mask=00004000/00000000
fsl_enetc 0000:00:00.1: [14] CorrIntErr
Further investigating the port correctable memory error detect register
(PCMEDR) shows that these AER errors have an associated SOURCE_ID of 6
(RFS/RSS):
$ devmem 0x1f8010e10 32
0xC0000006
$ devmem 0x1f8050e10 32
0xC0000006
Discussion with the hardware design engineers reveals that on LS1028A,
the hardware does not do initialization of that RFS/RSS memory, and that
software should clear/initialize the entire table before starting to
operate. That comes as a bit of a surprise, since the driver does not do
initialization of the RFS memory. Also, the initialization of the
Receive Side Scaling is done only partially.
Even though the entire ENETC IP has a single shared flow steering
memory, the flow steering service should returns matches only for TCAM
entries that are within the range of the Station Interface that is doing
the search. Therefore, it should be sufficient for a Station Interface
to initialize all of its own entries in order to avoid any ECC errors,
and only the Station Interfaces in use should need initialization.
There are Physical Station Interfaces associated with PCIe PFs and
Virtual Station Interfaces associated with PCIe VFs. We let the PF
driver initialize the entire port's memory, which includes the RFS
entries which are going to be used by the VF.
Reported-by: Michael Walle <michael@walle.cc>
Fixes: d4fd0404c1 ("enetc: Introduce basic PF and VF ENETC ethernet drivers")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Tested-by: Michael Walle <michael@walle.cc>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Link: https://lore.kernel.org/r/20210204134511.2640309-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Saeed Mahameed says:
====================
mlx5 fixes 2021-02-01
Please note the first patch in this series
("Fix function calculation for page trees") is fixing a regression
due to previous fix in net which you didn't include in your previous
rc pr. So I hope this series will make it into your next rc pr,
so mlx5 won't be broken in the next rc.
* tag 'mlx5-fixes-2021-02-01' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux:
net/mlx5e: Release skb in case of failure in tc update skb
net/mlx5e: Update max_opened_tc also when channels are closed
net/mlx5: Fix leak upon failure of rule creation
net/mlx5: Fix function calculation for page trees
====================
Link: https://lore.kernel.org/r/20210202070703.617251-1-saeed@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
So far phy_disconnect() is called before free_irq(). If CONFIG_DEBUG_SHIRQ
is set and interrupt is shared, then free_irq() creates an "artificial"
interrupt by calling the interrupt handler. The "link change" flag is set
in the interrupt status register, causing phylib to eventually call
phy_suspend(). Because the net_device is detached from the PHY already,
the PHY driver can't recognize that WoL is configured and powers down the
PHY.
Fixes: f1e911d5d0 ("r8169: add basic phylib support")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://lore.kernel.org/r/fe732c2c-a473-9088-3974-df83cfbd6efd@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In case of failure in tc update skb the packet is dropped
without freeing the skb.
Fixed by freeing the skb in case failure in tc update skb.
Fixes: d6d2778286 ("net/mlx5: E-Switch, Restore chain id on miss")
Fixes: c756909722 ("net/mlx5e: Add tc chains offload support for nic flows")
Signed-off-by: Maor Dickman <maord@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
max_opened_tc is used for stats, so that potentially non-zero stats
won't disappear when num_tc decreases. However, mlx5e_setup_tc_mqprio
fails to update it in the flow where channels are closed.
This commit fixes it. The new value of priv->channels.params.num_tc is
always checked on exit. In case of errors it will just be the old value,
and in case of success it will be the updated value.
Fixes: 05909babce ("net/mlx5e: Avoid reset netdev stats on configuration changes")
Signed-off-by: Maxim Mikityanskiy <maximmi@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
When creation of a new rule that requires allocation of an FTE fails,
need to call to tree_put_node on the FTE in order to release its'
resource.
Fixes: cefc23554f ("net/mlx5: Fix FTE cleanup")
Signed-off-by: Maor Gottlieb <maorg@nvidia.com>
Reviewed-by: Alaa Hleihel <alaa@nvidia.com>
Reviewed-by: Mark Bloch <mbloch@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
The function calculation always results in a value of 0. This works
generally, but when the release all pages feature is enabled it will
result in crashes.
Fixes: 0aa128475d ("net/mlx5: Maintain separate page trees for ECPF and PF functions")
Signed-off-by: Daniel Jurgens <danielj@nvidia.com>
Reported-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2021-02-01
This series contains updates to igc and i40e drivers.
Kai-Heng Feng fixes igc to report unknown speed and duplex during suspend
as an attempted read will cause errors.
Kevin Lo sets the default value to -IGC_ERR_NVM instead of success for
writing shadow RAM as this could miss a timeout. Also propagates the return
value for Flow Control configuration to properly pass on errors for igc.
Aleksandr reverts commit 2ad1274fa3 ("i40e: don't report link up for a VF
who hasn't enabled queues") as this can cause link flapping.
* '1GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue:
i40e: Revert "i40e: don't report link up for a VF who hasn't enabled queues"
igc: check return value of ret_val in igc_config_fc_after_link_up
igc: set the default return value to -IGC_ERR_NVM in igc_write_nvm_srwr
igc: Report speed and duplex as unknown when device is runtime suspended
====================
Link: https://lore.kernel.org/r/20210201214618.852831-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This reverts commit 2ad1274fa3
VF queues were not brought up when PF was brought up after being
downed if the VF driver disabled VFs queues during PF down.
This could happen in some older or external VF driver implementations.
The problem was that PF driver used vf->queues_enabled as a condition
to decide what link-state it would send out which caused the issue.
Remove the check for vf->queues_enabled in the VF link notify.
Now VF will always be notified of the current link status.
Also remove the queues_enabled member from i40e_vf structure as it is
not used anymore. Otherwise VNF implementation was broken and caused
a link flap.
The original commit was a workaround to avoid breaking existing VFs though
it's really a fault of the VF code not the PF. The commit should be safe to
revert as all of the VFs we know of have been fixed. Also, since we now
know there is a related bug in the workaround, removing it is preferred.
Fixes: 2ad1274fa3 ("i40e: don't report link up for a VF who hasn't enabled")
Signed-off-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Signed-off-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
This patch sets the default return value to -IGC_ERR_NVM in
igc_write_nvm_srwr. Without this change it wouldn't lead to a shadow RAM
write EEWR timeout.
Fixes: ab40561268 ("igc: Add NVM support")
Signed-off-by: Kevin Lo <kevlo@kevlo.org>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
It was reported that on RTL8125 network breaks under heavy UDP load,
e.g. torrent traffic ([0], from comment 27). Realtek confirmed a hw bug
and provided me with a test version of the r8125 driver including a
workaround. Tests confirmed that the workaround fixes the issue.
I modified the original version of the workaround to meet mainline
code style.
[0] https://bugzilla.kernel.org/show_bug.cgi?id=209839
v2:
- rebased to net
v3:
- make rtl_skb_is_udp() more robust and use skb_header_pointer()
to access the ip(v6) header
v4:
- remove dependency on ptp_classify.h
- replace magic number with offsetof(struct udphdr, len)
Fixes: f1bce4ad2f ("r8169: add support for RTL8125")
Tested-by: xplo <xplo.bn@gmail.com>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Link: https://lore.kernel.org/r/6e453d49-1801-e6de-d5f7-d7e6c7526c8f@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Pull networking fixes from Jakub Kicinski:
"Networking fixes including fixes from can, xfrm, wireless,
wireless-drivers and netfilter trees. Nothing scary, Intel
WiFi-related fixes seemed most notable to the users.
Current release - regressions:
- dsa: microchip: ksz8795: fix KSZ8794 port map again to program the
CPU port correctly
Current release - new code bugs:
- iwlwifi: pcie: reschedule in long-running memory reads
Previous releases - regressions:
- iwlwifi: dbg: don't try to overwrite read-only FW data
- iwlwifi: provide gso_type to GSO packets
- octeontx2: make sure the buffer is 128 byte aligned
- tcp: make TCP_USER_TIMEOUT accurate for zero window probes
- xfrm: fix wraparound in xfrm_policy_addr_delta()
- xfrm: fix oops in xfrm_replay_advance_bmp due to a race between
CPUs in presence of packet reorder
- tcp: fix TLP timer not set when CA_STATE changes from DISORDER to
OPEN
- wext: fix NULL-ptr-dereference with cfg80211's lack of commit()
Previous releases - always broken:
- igc: fix link speed advertising
- stmmac: configure EHL PSE0 GbE and PSE1 GbE to 32 bits DMA
addressing
- team: protect features update by RCU to avoid deadlock
- xfrm: fix disable_xfrm sysctl when used on xfrm interfaces
themselves
- fec: fix temporary RMII clock reset on link up
- can: dev: prevent potential information leak in can_fill_info()
Misc:
- mrp: fix bad packing of MRP test packet structures
- uapi: fix big endian definition of ipv6_rpl_sr_hdr
- add David Ahern to IPv4/IPv6 maintainers"
* tag 'net-5.11-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (86 commits)
rxrpc: Fix memory leak in rxrpc_lookup_local
mlxsw: spectrum_span: Do not overwrite policer configuration
selftests: forwarding: Specify interface when invoking mausezahn
stmmac: intel: Configure EHL PSE0 GbE and PSE1 GbE to 32 bits DMA addressing
net: usb: cdc_ether: added support for Thales Cinterion PLSx3 modem family.
ibmvnic: Ensure that CRQ entry read are correctly ordered
MAINTAINERS: add missing header for bonding
net: decnet: fix netdev refcount leaking on error path
net: switchdev: don't set port_obj_info->handled true when -EOPNOTSUPP
can: dev: prevent potential information leak in can_fill_info()
net: fec: Fix temporary RMII clock reset on link up
net: lapb: Add locking to the lapb module
team: protect features update by RCU to avoid deadlock
MAINTAINERS: add David Ahern to IPv4/IPv6 maintainers
net/mlx5: CT: Fix incorrect removal of tuple_nat_node from nat rhashtable
net/mlx5e: Revert parameters on errors when changing MTU and LRO state without reset
net/mlx5e: Revert parameters on errors when changing trust state without reset
net/mlx5e: Correctly handle changing the number of queues when the interface is down
net/mlx5e: Fix CT rule + encap slow path offload and deletion
net/mlx5e: Disable hw-tc-offload when MLX5_CLS_ACT config is disabled
...
The purpose of the delayed work in the SPAN module is to potentially
update the destination port and various encapsulation parameters of SPAN
agents that point to a VLAN device or a GRE tap. The destination port
can change following the insertion of a new route, for example.
SPAN agents that point to a physical port or the CPU port are static and
never change throughout the lifetime of the SPAN agent. Therefore, skip
over them in the delayed work.
This fixes an issue where the delayed work overwrites the policer
that was set on a SPAN agent pointing to the CPU. Modifying the delayed
work to inherit the original policer configuration is error-prone, as
the same will be needed for any new parameter.
Fixes: 4039504e6a ("mlxsw: spectrum_span: Allow setting policer on a SPAN agent")
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Pull rdma fixes from Jason Gunthorpe:
"Several recent regressions and some bug fixes:
- Typo corrupting the max_recv_sge for cxgb4
- Regression from re-using kernel enums as a HW AbI in vmw_pvrdma
- Sleeping inside a spinlock in hns
- Revert the attempt to fix devlink deadlocks as the fix is more buggy
- Typo in sysfs_emit_at conversions
- Revert the removal of VLAN support in rxe"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma:
Revert "RDMA/rxe: Remove VLAN code leftovers from RXE"
RDMA/usnic: Fix misuse of sysfs_emit_at
Revert "RDMA/mlx5: Fix devlink deadlock on net namespace deletion"
RDMA/hns: Use mutex instead of spinlock for ida allocation
RDMA/vmw_pvrdma: Fix network_hdr_type reported in WC
RDMA/cxgb4: Fix the reported max_recv_sge value
Saeed Mahameed says:
====================
mlx5 fixes 2021-01-26
This series introduces some fixes to mlx5 driver.
* tag 'mlx5-fixes-2021-01-26' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux:
net/mlx5: CT: Fix incorrect removal of tuple_nat_node from nat rhashtable
net/mlx5e: Revert parameters on errors when changing MTU and LRO state without reset
net/mlx5e: Revert parameters on errors when changing trust state without reset
net/mlx5e: Correctly handle changing the number of queues when the interface is down
net/mlx5e: Fix CT rule + encap slow path offload and deletion
net/mlx5e: Disable hw-tc-offload when MLX5_CLS_ACT config is disabled
net/mlx5: Maintain separate page trees for ECPF and PF functions
net/mlx5e: Fix IPSEC stats
net/mlx5e: Reduce tc unsupported key print level
net/mlx5e: free page before return
net/mlx5e: E-switch, Fix rate calculation for overflow
net/mlx5: Fix memory leak on flow table creation error flow
====================
Link: https://lore.kernel.org/r/20210126234345.202096-1-saeedm@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Ensure that received Command-Response Queue (CRQ) entries are
properly read in order by the driver. dma_rmb barrier has
been added before accessing the CRQ descriptor to ensure
the entire descriptor is read before processing.
Fixes: 032c5e8284 ("Driver for IBM System i/p VNIC protocol")
Signed-off-by: Lijun Pan <ljp@linux.ibm.com>
Link: https://lore.kernel.org/r/20210128013442.88319-1-ljp@linux.ibm.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Anthony Nguyen says:
====================
Intel Wired LAN Driver Updates 2021-01-26
This series contains updates to the ice, i40e, and igc driver.
Henry corrects setting an unspecified protocol to IPPROTO_NONE instead of
0 for IPv6 flexbytes filters for ice.
Nick fixes the IPv6 extension header being processed incorrectly and
updates the netdev->dev_addr if it exists in hardware as it may have been
modified outside the ice driver.
Brett ensures a user cannot request more channels than available LAN MSI-X
and fixes the minimum allocation logic as it was incorrectly trying to use
more MSI-X than allocated for ice.
Stefan Assmann minimizes the delay between getting and using the VSI
pointer to prevent a possible crash for i40e.
Corinna Vinschen fixes link speed advertising for igc.
* '100GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue:
igc: fix link speed advertising
i40e: acquire VSI pointer only after VF is initialized
ice: Fix MSI-X vector fallback logic
ice: Don't allow more channels than LAN MSI-X available
ice: update dev_addr in ice_set_mac_address even if HW filter exists
ice: Implement flow for IPv6 next header (extension header)
ice: fix FDir IPv6 flexbyte
====================
Link: https://lore.kernel.org/r/20210126221035.658124-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
fec_restart() does a hard reset of the MAC module when the link status
changes to up. This temporarily resets the R_CNTRL register which controls
the MII mode of the ENET_OUT clock. In the case of RMII, the clock
frequency momentarily drops from 50MHz to 25MHz until the register is
reconfigured. Some link partners do not tolerate this glitch and
invalidate the link causing failure to establish a stable link when using
PHY polling mode. Since as per IEEE802.3 the criteria for link validity
are PHY-specific, what the partner should tolerate cannot be assumed, so
avoid resetting the MII clock by using software reset instead of hardware
reset when the link is up. This is generally relevant only if the SoC
provides the clock to an external PHY and the PHY is configured for RMII.
Signed-off-by: Laurent Badel <laurentbadel@eaton.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
If a non nat tuple entry is inserted just to the regular tuples
rhashtable (ct_tuples_ht) and not to natted tuples rhashtable
(ct_nat_tuples_ht). Commit bc562be967 ("net/mlx5e: CT: Save ct entries
tuples in hashtables") mixed up the return labels and names sot that on
cleanup or failure we still try to remove for the natted tuples rhashtable.
Fix that by correctly checking if a natted tuples insertion
before removing it. While here make it more readable.
Fixes: bc562be967 ("net/mlx5e: CT: Save ct entries tuples in hashtables")
Reviewed-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: Paul Blakey <paulb@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Sometimes, channel params are changed without recreating the channels.
It happens in two basic cases: when the channels are closed, and when
the parameter being changed doesn't affect how channels are configured.
Such changes invoke a hardware command that might fail. The whole
operation should be reverted in such cases, but the code that restores
the parameters' values in the driver was missing. This commit adds this
handling.
Fixes: 2e20a15120 ("net/mlx5e: Fail safe mtu and lro setting")
Signed-off-by: Maxim Mikityanskiy <maximmi@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Trust state may be changed without recreating the channels. It happens
when the channels are closed, and when channel parameters (min inline
mode) stay the same after changing the trust state. Changing the trust
state is a hardware command that may fail. The current code didn't
restore the channel parameters to their old values if an error happened
and the channels were closed. This commit adds handling for this case.
Fixes: 6e0504c698 ("net/mlx5e: Change inline mode correctly when changing trust state")
Signed-off-by: Maxim Mikityanskiy <maximmi@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
This commit addresses two issues related to changing the number of
queues when the channels are closed:
1. Missing call to mlx5e_num_channels_changed to update
real_num_tx_queues when the number of TCs is changed.
2. When mlx5e_num_channels_changed returns an error, the channel
parameters must be reverted.
Two Fixes: tags correspond to the first commits where these two issues
were introduced.
Fixes: 3909a12e79 ("net/mlx5e: Fix configuration of XPS cpumasks and netdev queues in corner cases")
Fixes: fa3748775b ("net/mlx5e: Handle errors from netif_set_real_num_{tx,rx}_queues")
Signed-off-by: Maxim Mikityanskiy <maximmi@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Currently, if a neighbour isn't valid when offloading tunnel encap rules,
we offload the original match and replace the original action with
"goto slow path" action. For this we use a temporary flow attribute based
on the original flow attribute and then change the action. Flow flags,
which among those is the CT flag, are still shared for the slow path rule
offload, so we end up parsing this flow as a CT + goto slow path rule.
Besides being unnecessary, CT action offload saves extra information in
the passed flow attribute, such as created ct_flow and mod_hdr, which
is lost onces the temporary flow attribute is freed.
When a neigh is updated and is valid, we offload the original CT rule
with original CT action, which again creates a ct_flow and mod_hdr
and saves it in the flow's original attribute. Then we delete the slow
path rule with a temporary flow attribute based on original updated
flow attribute, and we free the relevant ct_flow and mod_hdr.
Then when tc deletes this flow, we try to free the ct_flow and mod_hdr
on the flow's attribute again.
To fix the issue, skip all furture proccesing (CT/Sample/Split rules)
in offload/unoffload of slow path rules.
Call trace:
[ 758.850525] Unable to handle kernel NULL pointer dereference at virtual address 0000000000000218
[ 758.952987] Internal error: Oops: 96000005 [#1] PREEMPT SMP
[ 758.964170] Modules linked in: act_csum(E) act_pedit(E) act_tunnel_key(E) act_ct(E) nf_flow_table(E) xt_nat(E) ip6table_filter(E) ip6table_nat(E) xt_comment(E) ip6_tables(E) xt_conntrack(E) xt_MASQUERADE(E) nf_conntrack_netlink(E) xt_addrtype(E) iptable_filter(E) iptable_nat(E) bpfilter(E) br_netfilter(E) bridge(E) stp(E) llc(E) xfrm_user(E) overlay(E) act_mirred(E) act_skbedit(E) rdma_ucm(OE) rdma_cm(OE) iw_cm(OE) ib_ipoib(OE) ib_cm(OE) ib_umad(OE) esp6_offload(E) esp6(E) esp4_offload(E) esp4(E) xfrm_algo(E) mlx5_ib(OE) ib_uverbs(OE) geneve(E) ip6_udp_tunnel(E) udp_tunnel(E) nfnetlink_cttimeout(E) nfnetlink(E) mlx5_core(OE) act_gact(E) cls_flower(E) sch_ingress(E) openvswitch(E) nsh(E) nf_conncount(E) nf_nat(E) mlxfw(OE) psample(E) nf_conntrack(E) nf_defrag_ipv4(E) vfio_mdev(E) mdev(E) ib_core(OE) mlx_compat(OE) crct10dif_ce(E) uio_pdrv_genirq(E) uio(E) i2c_mlx(E) mlxbf_pmc(E) sbsa_gwdt(E) mlxbf_gige(E) gpio_mlxbf2(E) mlxbf_pka(E) mlx_trio(E) mlx_bootctl(E) bluefield_edac(E) knem(O)
[ 758.964225] ip_tables(E) mlxbf_tmfifo(E) ipv6(E) crc_ccitt(E) nf_defrag_ipv6(E)
[ 759.154186] CPU: 5 PID: 122 Comm: kworker/u16:1 Tainted: G OE 5.4.60-mlnx.52.gde81e85 #1
[ 759.172870] Hardware name: https://www.mellanox.com BlueField SoC/BlueField SoC, BIOS BlueField:3.5.0-2-gc1b5d64 Jan 4 2021
[ 759.195466] Workqueue: mlx5e mlx5e_rep_neigh_update [mlx5_core]
[ 759.207344] pstate: a0000005 (NzCv daif -PAN -UAO)
[ 759.217003] pc : mlx5_del_flow_rules+0x5c/0x160 [mlx5_core]
[ 759.228229] lr : mlx5_del_flow_rules+0x34/0x160 [mlx5_core]
[ 759.405858] Call trace:
[ 759.410804] mlx5_del_flow_rules+0x5c/0x160 [mlx5_core]
[ 759.421337] __mlx5_eswitch_del_rule.isra.43+0x5c/0x1c8 [mlx5_core]
[ 759.433963] mlx5_eswitch_del_offloaded_rule_ct+0x34/0x40 [mlx5_core]
[ 759.446942] mlx5_tc_rule_delete_ct+0x68/0x74 [mlx5_core]
[ 759.457821] mlx5_tc_ct_delete_flow+0x160/0x21c [mlx5_core]
[ 759.469051] mlx5e_tc_unoffload_fdb_rules+0x158/0x168 [mlx5_core]
[ 759.481325] mlx5e_tc_encap_flows_del+0x140/0x26c [mlx5_core]
[ 759.492901] mlx5e_rep_update_flows+0x11c/0x1ec [mlx5_core]
[ 759.504127] mlx5e_rep_neigh_update+0x160/0x200 [mlx5_core]
[ 759.515314] process_one_work+0x178/0x400
[ 759.523350] worker_thread+0x58/0x3e8
[ 759.530685] kthread+0x100/0x12c
[ 759.537152] ret_from_fork+0x10/0x18
[ 759.544320] Code: 97ffef55 51000673 3100067f 54ffff41 (b9421ab3)
[ 759.556548] ---[ end trace fab818bb1085832d ]---
Fixes: 4c3844d9e9 ("net/mlx5e: CT: Introduce connection tracking")
Signed-off-by: Paul Blakey <paulb@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Reviewed-by: Vlad Buslov <vladbu@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
The cited commit introduce new CONFIG_MLX5_CLS_ACT kconfig variable
to control compilation of TC hardware offloads implementation.
When this configuration is disabled the driver is still wrongly
reports in ethtool that hw-tc-offload is supported.
Fixed by reporting hw-tc-offload is supported only when
CONFIG_MLX5_CLS_ACT is enabled.
Fixes: d956873f90 ("net/mlx5e: Introduce kconfig var for TC support")
Signed-off-by: Maor Dickman <maord@nvidia.com>
Reviewed-by: Vlad Buslov <vladbu@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Pages for the host PF and ECPF were stored in the same tree, so the ECPF
pages were being freed along with the host PF's when the host driver
unloaded.
Combine the function ID and ECPF flag to use as an index into the
x-array containing the trees to get a different tree for the host PF and
ECPF.
Fixes: c6168161f6 ("net/mlx5: Add support for release all pages event")
Signed-off-by: Daniel Jurgens <danielj@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
When IPSEC offload isn't active, the number of stats is not zero, but
the strings are not filled, leading to exposing stats with empty names.
Fix this by using the same condition for NUM_STATS and FILL_STRS.
Fixes: 0aab3e1b04 ("net/mlx5e: IPSec, Expose IPsec HW stat only for supporting HW")
Signed-off-by: Maxim Mikityanskiy <maximmi@mellanox.com>
Reviewed-by: Raed Salem <raeds@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
"Unsupported key used:" appears in kernel log when flows with
unsupported key are used, arp fields for example.
OpenVSwitch was changed to match on arp fields by default that
caused this warning to appear in kernel log for every arp rule, which
can be a lot.
Fix by lowering print level from warning to debug.
Fixes: e3a2b7ed01 ("net/mlx5e: Support offload cls_flower with drop action")
Signed-off-by: Maor Dickman <maord@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Reviewed-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Instead of directly return, goto the error handling label to free
allocated page.
Fixes: 5f29458b77 ("net/mlx5e: Support dump callback in TX reporter")
Signed-off-by: Pan Bian <bianpan2016@163.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
rate_bytes_ps is a 64-bit field. It passed as 32-bit field to
apply_police_params(). Due to this when police rate is higher
than 4Gbps, 32-bit calculation ignores the carry. This results
in incorrect rate configurationn the device.
Fix it by performing 64-bit calculation.
Fixes: fcb64c0f56 ("net/mlx5: E-Switch, add ingress rate support")
Signed-off-by: Parav Pandit <parav@nvidia.com>
Reviewed-by: Eli Cohen <elic@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
When we create the ft object we also init rhltable in ft->fgs_hash.
So in error flow before kfree of ft we need to destroy that rhltable.
Fixes: 693c6883bb ("net/mlx5: Add hash table for flow groups in flow table")
Signed-off-by: Roi Dayan <roid@nvidia.com>
Reviewed-by: Maor Dickman <maord@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Link speed advertising in igc has two problems:
- When setting the advertisement via ethtool, the link speed is converted
to the legacy 32 bit representation for the intel PHY code.
This inadvertently drops ETHTOOL_LINK_MODE_2500baseT_Full_BIT (being
beyond bit 31). As a result, any call to `ethtool -s ...' drops the
2500Mbit/s link speed from the PHY settings. Only reloading the driver
alleviates that problem.
Fix this by converting the ETHTOOL_LINK_MODE_2500baseT_Full_BIT to the
Intel PHY ADVERTISE_2500_FULL bit explicitly.
- Rather than checking the actual PHY setting, the .get_link_ksettings
function always fills link_modes.advertising with all link speeds
the device is capable of.
Fix this by checking the PHY autoneg_advertised settings and report
only the actually advertised speeds up to ethtool.
Fixes: 8c5ad0dae9 ("igc: Add ethtool support")
Signed-off-by: Corinna Vinschen <vinschen@redhat.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
This change simplifies the VF initialization check and also minimizes
the delay between acquiring the VSI pointer and using it. As known by
the commit being fixed, there is a risk of the VSI pointer getting
changed. Therefore minimize the delay between getting and using the
pointer.
Fixes: 9889707b06 ("i40e: Fix crash caused by stress setting of VF MAC addresses")
Signed-off-by: Stefan Assmann <sassmann@kpanic.de>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The current MSI-X enablement logic tries to enable best-case MSI-X
vectors and if that fails we only support a bare-minimum set. This
includes a single MSI-X for 1 Tx and 1 Rx queue and a single MSI-X
for the OICR interrupt. Unfortunately, the driver fails to load when we
don't get as many MSI-X as requested for a couple reasons.
First, the code to allocate MSI-X in the driver tries to allocate
num_online_cpus() MSI-X for LAN traffic without caring about the number
of MSI-X actually enabled/requested from the kernel for LAN traffic.
So, when calling ice_get_res() for the PF VSI, it returns failure
because the number of available vectors is less than requested. Fix
this by not allowing the PF VSI to allocation more than
pf->num_lan_msix MSI-X vectors and pf->num_lan_msix Rx/Tx queues.
Limiting the number of queues is done because we don't want more than
1 Tx/Rx queue per interrupt due to performance conerns.
Second, the driver assigns pf->num_lan_msix = 2, to account for LAN
traffic and the OICR. However, pf->num_lan_msix is only meant for LAN
MSI-X. This is causing a failure when the PF VSI tries to
allocate/reserve the minimum pf->num_lan_msix because the OICR MSI-X has
already been reserved, so there may not be enough MSI-X vectors left.
Fix this by setting pf->num_lan_msix = 1 for the failure case. Then the
ICE_MIN_MSIX accounts for the LAN MSI-X and the OICR MSI-X needed for
the failure case.
Update the related defines used in ice_ena_msix_range() to align with
the above behavior and remove the unused RDMA defines because RDMA is
currently not supported. Also, remove the now incorrect comment.
Fixes: 152b978a1f ("ice: Rework ice_ena_msix_range")
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Currently users could create more channels than LAN MSI-X available.
This is happening because there is no check against pf->num_lan_msix
when checking the max allowed channels and will cause performance issues
if multiple Tx and Rx queues are tied to a single MSI-X. Fix this by not
allowing more channels than LAN MSI-X available in pf->num_lan_msix.
Fixes: 87324e747f ("ice: Implement ethtool ops for channels")
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
