Pull ARM SoC fixes from Arnd Bergmann:
"The code fixes in this round are all for the Texas Instruments OMAP
platform, addressing several regressions related to the ti-sysc
interconnect changes that was merged in linux-5.11 and one recently
introduced RCU usage warning.
Tero Kristo updates his maintainer file entries as he is changing to a
new employer.
The other changes are for devicetree files across eight different
platforms:
TI OMAP:
- multiple gpio related one-line fixes
Allwinner/sunxi:
- ARM: dts: sun7i: a20: bananapro: Fix ethernet phy-mode
- soc: sunxi: mbus: Remove DE2 display engine compatibles
NXP lpc32xx:
- ARM: dts: lpc32xx: Revert set default clock rate of HCLK PLL
STMicroelectronics stm32
- multiple minor fixes for DHCOM/DHCOR boards
NXP Layerscape:
- Fix DCFG address range on LS1046A SoC
Amlogic meson:
- fix reboot issue on odroid C4
- revert an ethernet change that caused a regression
- meson-g12: Set FL-adj property value
Rockchip:
- multiple minor fixes on 64-bit rockchip machines
Qualcomm:
- Regression fixes for Lenovo Yoga touchpad and for interconnect
configuration
- Boot fixes for 'LPASS' clock configuration on two machines"
* tag 'arm-soc-fixes-v5.11-3' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (31 commits)
ARM: dts: lpc32xx: Revert set default clock rate of HCLK PLL
ARM: dts: sun7i: a20: bananapro: Fix ethernet phy-mode
arm64: dts: ls1046a: fix dcfg address range
soc: sunxi: mbus: Remove DE2 display engine compatibles
arm64: dts: meson: switch TFLASH_VDD_EN pin to open drain on Odroid-C4
Revert "arm64: dts: amlogic: add missing ethernet reset ID"
arm64: dts: rockchip: Disable display for NanoPi R2S
ARM: dts: omap4-droid4: Fix lost keypad slide interrupts for droid4
arm64: dts: rockchip: remove interrupt-names property from rk3399 vdec node
drivers: bus: simple-pm-bus: Fix compatibility with simple-bus for auxdata
ARM: OMAP2+: Fix booting for am335x after moving to simple-pm-bus
ARM: OMAP2+: Fix suspcious RCU usage splats for omap_enter_idle_coupled
ARM: dts: stm32: Fix GPIO hog flags on DHCOM DRC02
ARM: dts: stm32: Fix GPIO hog flags on DHCOM PicoITX
ARM: dts: stm32: Fix GPIO hog names on DHCOM
ARM: dts: stm32: Disable optional TSC2004 on DRC02 board
ARM: dts: stm32: Disable WP on DHCOM uSD slot
ARM: dts: stm32: Connect card-detect signal on DHCOM
ARM: dts: stm32: Fix polarity of the DH DRC02 uSD card detect
arm64: dts: qcom: sdm845: Reserve LPASS clocks in gcc
...
One fix for a phy-mode ethernet issue, and one to fix the display output on
SoCs with the Display Engine 2
* tag 'sunxi-fixes-for-5.11-2' of git://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
ARM: dts: sun7i: a20: bananapro: Fix ethernet phy-mode
soc: sunxi: mbus: Remove DE2 display engine compatibles
Link: https://lore.kernel.org/r/f8298059-f9ca-43b4-9e29-35bc0e0c9b15.lettre@localhost
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This reverts commit c17e9377aa.
The lpc32xx clock driver is not able to actually change the PLL rate as
this would require reparenting ARM_CLK, DDRAM_CLK, PERIPH_CLK to SYSCLK,
then stop the PLL, update the register, restart the PLL and wait for the
PLL to lock and finally reparent ARM_CLK, DDRAM_CLK, PERIPH_CLK to HCLK
PLL.
Currently, the HCLK driver simply updates the registers but this has no
real effect and all the clock rate calculation end up being wrong. This is
especially annoying for the peripheral (e.g. UARTs, I2C, SPI).
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Tested-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Link: https://lore.kernel.org/r/20210203090320.GA3760268@piout.net'
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
BPi Pro needs TX and RX delay for Gbit to work reliable and avoid high
packet loss rates. The realtek phy driver overrides the settings of the
pull ups for the delays, so fix this for BananaPro.
Fix the phy-mode description to correctly reflect this so that the
implementation doesn't reconfigure the delays incorrectly. This
happened with commit bbc4d71d63 ("net: phy: realtek: fix rtl8211e
rx/tx delay config").
Fixes: 10662a33dc ("ARM: dts: sun7i: Add dts file for Bananapro board")
Signed-off-by: Hermann Lauer <Hermann.Lauer@uni-heidelberg.de>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20210128111842.GA11919@lemon.iwr.uni-heidelberg.de
Pull devicetree fixes from Rob Herring:
- Cleanups on properties with standard unit suffixes
- Fix overwriting dma_range_map if there's no 'dma-ranges' property
- Fix a bug when creating a /chosen node from ARM ATAGs
- Add missing properties for TI j721e USB binding
- Several doc reference updates due to DT schema conversions
* tag 'devicetree-fixes-for-5.11-2' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux:
dt-bindings: Cleanup standard unit properties
of/device: Update dma_range_map only when dev has valid dma-ranges
ARM: zImage: atags_to_fdt: Fix node names on added root nodes
dt-bindings: usb: j721e: add ranges and dma-coherent props
dt-bindings:iio:adc: update adc.yaml reference
dt-bindings: memory: mediatek: update mediatek,smi-larb.yaml references
dt-bindings: display: mediatek: update mediatek,dpi.yaml reference
ASoC: audio-graph-card: update audio-graph-card.yaml reference
Fixes for omaps for v5.11-rc cycle
The recent changes to switch SoCs to boot with ti-sysc interconnect
target module driver and genpd caused few regressions:
- The omap_prm reset driver needs to clear any reset bits deasserted by
the bootloader or kexec boot for the three reset bit cases. Otherwise
we can have an oops with accelerators starting to boot with potentially
unconfigured MMU for example
- Custom kernel configs are not automatically selecting simple-pm-bus
driver that we now need to probe interconnects so we need to select it
always
- We are not passing legacy platform data in auxdata with simple-pm-bus
like we do for simple-bus. We need to pass auxdata to simple-pm-bus so
it can pass it to of_platform_populate()
Then recent RCU changes started causing splats for cpuidle44xx that now
need RCU_NONIDLE added to the calls in several places
And then we have few device specific fixes:
- We need to remove legacy spi-cs-hig for gta04 display to work, and
set the gpio to active low
- Omap1 specific ohci-omap needs to call gpio_free()
- Droid4 needs to use padconf interrupt for the slider as the edge
gpio interrupts may be lost for deeper idle states
* tag 'omap-for-v5.11/fixes-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: omap4-droid4: Fix lost keypad slide interrupts for droid4
drivers: bus: simple-pm-bus: Fix compatibility with simple-bus for auxdata
ARM: OMAP2+: Fix booting for am335x after moving to simple-pm-bus
ARM: OMAP2+: Fix suspcious RCU usage splats for omap_enter_idle_coupled
ARM: dts; gta04: SPI panel chip select is active low
soc: ti: omap-prm: Fix boot time errors for rst_map_012 bits 0 and 1
ARM: OMAP1: OSK: fix ohci-omap breakage
DTS: ARM: gta04: remove legacy spi-cs-high to make display work again
Link: https://lore.kernel.org/r/pull-1611818709-243493@atomide.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
We may lose edge interrupts for gpio banks other than the first gpio
bank as they are not always powered. Instead, we must use the padconf
interrupt as that is always powered.
Note that we still also use the gpio for reading the pin state as that
can't be done with the padconf device.
Signed-off-by: Tony Lindgren <tony@atomide.com>
The PHY address bit 2 is configured by the LED pin. Attaching a LED
to this pin is not sufficient to guarantee this configuration pin is
correctly read. This leads to some platforms having their PHY at
address 0 and others at address 4.
If there is no phy-handle specified, the FEC driver will scan the PHY
bus for a PHY and use that. Consequently, adding the DT configuration
of the PHY and the phy properties to the FEC driver broke some boards.
Fix this by removing the phy-handle property, and listing two PHY
entries for both possible PHY addresses, so that the DT configuration
for the PHY can be found by the PHY driver.
Fixes: 86b08bd5b9 ("ARM: dts: imx6-sr-som: add ethernet PHY configuration")
Reported-by: Christoph Mattheis <christoph.mattheis@arcor.de>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The Ux500 platforms have some memory carveouts set aside for
communicating with the modem and for the initial secure software
(ISSW). These areas are protected by the memory controller
and will result in an external abort if accessed like common
read/write memory.
On the legacy boot loaders, these were set aside by using
cmdline arguments such as this:
mem=96M@0 mem_mtrace=15M@96M mem_mshared=1M@111M
mem_modem=16M@112M mali.mali_mem=32M@128M mem=96M@160M
hwmem=127M@256M mem_issw=1M@383M mem_ram_console=1M@384M
mem=638M@385M
Reserve the relevant areas in the device tree instead. The
"mali", "hwmem", "mem_ram_console" and the trailing 1MB at the
end of the memory reservations in the list are not relevant for
the upstream kernel as these are nowadays replaced with
upstream technologies such as CMA. The modem and ISSW
reservations are necessary.
This was manifested in a bug that surfaced in response to
commit 7fef431be9 ("mm/page_alloc: place pages to tail in __free_pages_core()")
which changes the behaviour of memory allocations
in such a way that the platform will sooner run into these
dangerous areas, with "Unhandled fault: imprecise external
abort (0xc06) at 0xb6fd83dc" or similar: the real reason
turns out to be that the PTE is pointing right into one of
the reserved memory areas. We were just lucky until now.
We need to augment the DB8500 and DB8520 SoCs similarly
and also create a new include for the DB9500 used in the
Snowball since this does not have a modem and thus does
not need the modem memory reservation, albeit it needs
the ISSW reservation.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Cc: stable@vger.kernel.org
Cc: David Hildenbrand <david@redhat.com>
Link: https://lore.kernel.org/r/20201213225517.3838501-1-linus.walleij@linaro.org'
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
i.MX fixes for 5.11:
- Fix backlight pwm on imx6qdl-kontron-samx6i which is lost from
#pwm-cells conversion.
- Fix duplicated bus node name for i.MX8MN SoC.
- Fix reset register offset on LS1028A SoC.
- Rename MMC node aliases for imx6q-tbs2910 to keep the MMC device
index consistent with previous kernel version.
- Selecting ARM_GIC_V3 on non-CP15 processors to fix one build failure
with i.MX8M SoC driver.
- Fix typos with status property on imx6qdl-kontron-samx6i board.
- Fix duplicated regulator-name on imx6qdl-gw52xx board.
* tag 'imx-fixes-5.11' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
ARM: dts: imx6qdl-gw52xx: fix duplicate regulator naming
ARM: dts: imx6qdl-kontron-samx6i: fix i2c_lcd/cam default status
ARM: imx: fix imx8m dependencies
ARM: dts: tbs2910: rename MMC node aliases
arm64: dts: ls1028a: fix the offset of the reset register
arm64: dts: imx8mn: Fix duplicate node name
ARM: dts: imx6qdl-kontron-samx6i: fix pwms for lcd-backlight
Link: https://lore.kernel.org/r/20210112131224.GI28365@dragon
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The GPIO hog node name should match regex '^(hog-[0-9]+|.+-hog(-[0-9]+)?)$',
make it so and fix the following two make dtbs_check warnings:
arch/arm/boot/dts/stm32mp157c-dhcom-picoitx.dt.yaml: hog-usb-port-power: $nodename:0: 'hog-usb-port-power' does not match '^(hog-[0-9]+|.+-hog(-[0-9]+)?)$'
arch/arm/boot/dts/stm32mp153c-dhcom-drc02.dt.yaml: hog-usb-hub: $nodename:0: 'hog-usb-hub' does not match '^(hog-[0-9]+|.+-hog(-[0-9]+)?)$'
Fixes: ac68793f49 ("ARM: dts: stm32: Add DHCOM based PicoITX board")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
to be consistent with kernel versions up to v5.9 (mmc aliases not used here).
usdhc1 is not wired up on this board and therefore cannot be used.
Start mmc aliases with usdhc2.
Signed-off-by: Soeren Moch <smoch@web.de>
Cc: stable@vger.kernel.org # 5.10.x
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Pull ARM SoC fixes from Arnd Bergmann:
"These are a small number of bug fixes that all came in before or
during the merge window, most for the omap platform:
- One boot regression fix for Nokia N9 (OMAP3).
- Two small defconfig changes for omap2, to reflect changes in
drivers
- Warning fixes for DT issues on omap2, picoxcell and bitmap SoCs.
The picoxcell platform will be removed in v5.12, but fixing it
first makes it easier to backport to the fix to stable kernels and
get a clean build with new dtc versions"
* tag 'arm-fixes-5.11-1' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc:
ARM: picoxcell: fix missing interrupt-parent properties
ARM: dts: ux500/golden: Set display max brightness
arm64: dts: bitmain: Use generic "ngpios" rather than "snps,nr-gpios"
ARM: omap2: pmic-cpcap: fix maximum voltage to be consistent with defaults on xt875
ARM: omap2plus_defconfig: enable SPI GPIO
ARM: OMAP2+: omap_device: fix idling of devices during probe
ARM: dts: OMAP3: disable AES on N950/N9
ARM: omap2plus_defconfig: drop unused POWER_AVS option
The pwms property have to specify the no-/inverted flag since
commit fa28d8212e ("ARM: dts: imx: default to #pwm-cells = <3>
in the SoC dtsi files").
Fixes: fa28d8212e ("ARM: dts: imx: default to #pwm-cells = <3> in the SoC dtsi files")
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
With the arrival of
commit 2fee958319 ("spi: dt-bindings: clarify CS behavior for spi-cs-high and gpio descriptors")
it was clarified what the proper state for cs-gpios should be, even if the
flag is ignored. The driver code is doing the right thing since
766c6b63aa ("spi: fix client driver breakages when using GPIO descriptors")
The chip-select of the td028ttec1 panel is active-low, so we must omit spi-cs-high;
attribute (already removed by separate patch) and should now use GPIO_ACTIVE_LOW for
the client device description to be fully consistent.
Fixes: 766c6b63aa ("spi: fix client driver breakages when using GPIO descriptors")
CC: stable@vger.kernel.org
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Pull ARM updates from Russell King:
- Rework phys/virt translation
- Add KASan support
- Move DT out of linear map region
- Use more PC-relative addressing in assembly
- Remove FP emulation handling while in kernel mode
- Link with '-z norelro'
- remove old check for GCC <= 4.2 in ARM unwinder code
- disable big endian if using clang's linker
* tag 'for-linus' of git://git.armlinux.org.uk/~rmk/linux-arm: (46 commits)
ARM: 9027/1: head.S: explicitly map DT even if it lives in the first physical section
ARM: 9038/1: Link with '-z norelro'
ARM: 9037/1: uncompress: Add OF_DT_MAGIC macro
ARM: 9036/1: uncompress: Fix dbgadtb size parameter name
ARM: 9035/1: uncompress: Add be32tocpu macro
ARM: 9033/1: arm/smp: Drop the macro S(x,s)
ARM: 9032/1: arm/mm: Convert PUD level pgtable helper macros into functions
ARM: 9031/1: hyp-stub: remove unused .L__boot_cpu_mode_offset symbol
ARM: 9044/1: vfp: use undef hook for VFP support detection
ARM: 9034/1: __div64_32(): straighten up inline asm constraints
ARM: 9030/1: entry: omit FP emulation for UND exceptions taken in kernel mode
ARM: 9029/1: Make iwmmxt.S support Clang's integrated assembler
ARM: 9028/1: disable KASAN in call stack capturing routines
ARM: 9026/1: unwind: remove old check for GCC <= 4.2
ARM: 9025/1: Kconfig: CPU_BIG_ENDIAN depends on !LD_IS_LLD
ARM: 9024/1: Drop useless cast of "u64" to "long long"
ARM: 9023/1: Spelling s/mmeory/memory/
ARM: 9022/1: Change arch/arm/lib/mem*.S to use WEAK instead of .weak
ARM: kvm: replace open coded VA->PA calculations with adr_l call
ARM: head.S: use PC relative insn sequence to calculate PHYS_OFFSET
...
The DTB magic marker is stored as a 32-bit big-endian value, and thus
depends on the CPU's endianness. Add a macro to define this value in
native endianness, to reduce #ifdef clutter and (future) duplication.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Ard Biesheuvel <ardb@kernel.org>
Reviewed-by: Nicolas Pitre <nico@fluxnic.net>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
DTB stores all values as 32-bit big-endian integers.
Add a macro to convert such values to native CPU endianness, to reduce
duplication.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Ard Biesheuvel <ardb@kernel.org>
Reviewed-by: Nicolas Pitre <nico@fluxnic.net>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
This reverts
commit f1f028ff89 ("DTS: ARM: gta04: introduce legacy spi-cs-high to make display work again")
which had to be intruduced after
commit 6953c57ab1 ("gpio: of: Handle SPI chipselect legacy bindings")
broke the GTA04 display. This contradicted the data sheet but was the only
way to get it as an spi client operational again.
The panel data sheet defines the chip-select to be active low.
Now, with the arrival of
commit 766c6b63aa ("spi: fix client driver breakages when using GPIO descriptors")
the logic of interaction between spi-cs-high and the gpio descriptor flags
has been changed a second time, making the display broken again. So we have
to remove the original fix which in retrospect was a workaround of a bug in
the spi subsystem and not a feature of the panel or bug in the device tree.
With this fix the device tree is back in sync with the data sheet and
spi subsystem code.
Fixes: 766c6b63aa ("spi: fix client driver breakages when using GPIO descriptors")
CC: stable@vger.kernel.org
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Pull ARM SoC OMAP GenPD updates from Arnd Bergmann:
"These are additional updates for the power domain support on OMAP,
moving to an implementation based on device tree information instead
of SoC specific code. This is the latest step in the ongoing process
for moving code out of arch/arm/mach-omap2.
I kept this separate from the other driver changes since it touches
code in multiple areas"
* tag 'arm-soc-omap-genpd-5.11' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (51 commits)
ARM: OMAP2+: Fix am4 only build after genpd changes
ARM: dts: Configure power domain for omap5 dss
ARM: dts: omap5: add remaining PRM instances
soc: ti: omap-prm: omap5: add genpd support for remaining PRM instances
ARM: OMAP2+: Drop legacy platform data for dra7 gpmc
ARM: dts: Configure interconnect target module for dra7 iva
ARM: dts: dra7: add remaining PRM instances
soc: ti: omap-prm: dra7: add genpd support for remaining PRM instances
clk: ti: dra7: Drop idlest polling from IVA clkctrl clocks
ARM: OMAP2+: Drop legacy platform data for omap4 gpmc
ARM: OMAP2+: Drop legacy platform data for omap4 iva
ARM: dts: Configure power domain for omap4 dsp
ARM: dts: Configure power domain for omap4 dss
ARM: dts: omap4: add remaining PRM instances
soc: ti: omap-prm: omap4: add genpd support for remaining PRM instances
clk: ti: omap4: Drop idlest polling from IVA clkctrl clocks
ARM: OMAP2+: Drop legacy remaining legacy platform data for am4
ARM: dts: Use simple-pm-bus for genpd for am4 l3
ARM: dts: Move am4 l3 noc to a separate node
ARM: dts: Use simple-pm-bus for genpd for am4 l4_per
...
Pull ARM SoC driver updates from Arnd Bergmann:
"There are a couple of subsystems maintained by other people that merge
their drivers through the SoC tree, those changes include:
- The SCMI firmware framework gains support for sensor notifications
and for controlling voltage domains.
- A large update for the Tegra memory controller driver, integrating
it better with the interconnect framework
- The memory controller subsystem gains support for Mediatek MT8192
- The reset controller framework gains support for sharing pulsed
resets
For Soc specific drivers in drivers/soc, the main changes are
- The Allwinner/sunxi MBUS gets a rework for the way it handles
dma_map_ops and offsets between physical and dma address spaces.
- An errata fix plus some cleanups for Freescale Layerscape SoCs
- A cleanup for renesas drivers regarding MMIO accesses.
- New SoC specific drivers for Mediatek MT8192 and MT8183 power
domains
- New SoC specific drivers for Aspeed AST2600 LPC bus control and SoC
identification.
- Core Power Domain support for Qualcomm MSM8916, MSM8939, SDM660 and
SDX55.
- A rework of the TI AM33xx 'genpd' power domain support to use
information from DT instead of platform data
- Support for TI AM64x SoCs
- Allow building some Amlogic drivers as modules instead of built-in
Finally, there are numerous cleanups and smaller bug fixes for
Mediatek, Tegra, Samsung, Qualcomm, TI OMAP, Amlogic, Rockchips,
Renesas, and Xilinx SoCs"
* tag 'arm-soc-drivers-5.11' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (222 commits)
soc: mediatek: mmsys: Specify HAS_IOMEM dependency for MTK_MMSYS
firmware: xilinx: Properly align function parameter
firmware: xilinx: Add a blank line after function declaration
firmware: xilinx: Remove additional newline
firmware: xilinx: Fix kernel-doc warnings
firmware: xlnx-zynqmp: fix compilation warning
soc: xilinx: vcu: add missing register NUM_CORE
soc: xilinx: vcu: use vcu-settings syscon registers
dt-bindings: soc: xlnx: extract xlnx, vcu-settings to separate binding
soc: xilinx: vcu: drop useless success message
clk: samsung: mark PM functions as __maybe_unused
soc: samsung: exynos-chipid: initialize later - with arch_initcall
soc: samsung: exynos-chipid: order list of SoCs by name
memory: jz4780_nemc: Fix potential NULL dereference in jz4780_nemc_probe()
memory: ti-emif-sram: only build for ARMv7
memory: tegra30: Support interconnect framework
memory: tegra20: Support hardware versioning and clean up OPP table initialization
dt-bindings: memory: tegra20-emc: Document opp-supported-hw property
soc: rockchip: io-domain: Fix error return code in rockchip_iodomain_probe()
reset-controller: ti: force the write operation when assert or deassert
...
Pull ARM device tree updates from Arnd Bergmann:
"Across all platforms, there is a continued move towards DT schema for
validating the dts files. As a result there are bug fixes for mistakes
that are found using these schema, in addition to warnings from the
dtc compiler.
As usual, many changes are for adding support for additional on-chip
and on-board components in the machines we already support.
The newly supported SoCs for this release are:
- MStar Infinity2M, a low-end IP camera chip based on a dual-core
Cortex-A7, otherwise similar to the Infinity chip we already
support. This is also known as the SigmaStar SSD202D, and we add
support for the Honestar ssd201htv2 development kit.
- Nuvoton NPCM730, a Cortex-A9 based Baseboard Management Controller
(BMC), in the same family as the NPCM750. This gets used in the
Ampere Altra based "Fii Kudo" server and the Quanta GSJ, both of
which are added as well.
- Broadcom BCM4908, a 64-bit home router chip based on Broadcom's own
Brahma-B53 CPU. Support is also added for the Asus ROG Rapture
GT-AC5300 high-end WiFi router based on this chip.
- Mediatek MT8192 is a new SoC based on eight Cortex-A76/A55 cores,
meant for faster Chromebooks and tablets. It gets added along with
its reference design.
- Mediatek MT6779 (Helio P90) is a high-end phone chip from last
year's generation, also added along with its reference board. This
one is still based on Cortex-A75/A55.
- Mediatek MT8167 is a version of the already supported MT8516 chip,
both based on Cortex-A35. It gets added along with the "Pumpkin"
single board computer, but is likely to also make its way into
low-end tablets in the future.
For the already supported chips, there are a number of new boards.
Interestingly there are more 32-bit machines added this time than
64-bit. Here is a brief list of the new boards:
- Three new Mikrotik router variants based on Marvell Prestera
98DX3236, a close relative of the more common Armada XP
- A reference board for the Marvell Armada 382
- Three new servers using ASpeed baseboard management controllers,
the actual machines being from Bytedance, Facebook and IBM, and one
machine using the Nuvoton NPCM750 BMC.
- The Galaxy Note 10.1 (P4) tablet, using an Exynos 4412.
- The usual set of 32-bit i.MX industrial/embedded hardware:
* Protonic WD3 (tractor e-cockpit)
* Kamstrup OMNIA Flex Concentrator (smart grid platform)
* Van der Laan LANMCU (food storage)
* Altesco I6P (vehicle inspection stations)
* PHYTEC phyBOARD-Segin/phyCORE-i.MX6UL baseboard
- DH electronics STM32MP157C DHCOM, a PicoITX carrier board for the
aleady supported DHCOM module
- Three new Allwinner SoC based single-board computers:
* NanoPi R1 (H3 based)
* FriendlyArm ZeroPi (H3 based)
* Elimo Initium SBC (S3 based)
- Ouya Game Console based on Nvidia Tegra 3
- Version 5 of the already supported Zynq Z-Turn MYIR Board
- LX2162AQDS, a reference platform for NXP Layerscape LX2162A, which
is a repackaged 16-core LX2160A
- A series of Kontron i.MX8M Mini baseboard/SoM versions
- Espressobin Ultra, a new variant of the popular Armada 3700 based
board,
- IEI Puzzle-M801, a rackmount network appliance based on Marvell
Armada 8040
- Microsoft Lumia 950 XL, a phone
- HDK855 and HDK865 Hardware development kits for Qualcomm sm8250 and
sm8150, respectively
- Three new board variants of the "Trogdor" Chromebook (sc7180)
- New board variants of the Renesas based "Kingfisher" and "HiHope"
reference boards
- Kobol Helios64, an open source NAS appliance based on Rockchips
RK3399
- Engicam PX30.Core, a SoM based on Rockchip PX30, along with a few
carrier boards"
* tag 'arm-soc-dt-5.11' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (679 commits)
arm64: dts: sparx5: Add SGPIO devices
arm64: dts: sparx5: Add reset support
dt-bindings: gpio: Add a binding header for the MSC313 GPIO driver
ARM: mstar: SMP support
ARM: mstar: Wire up smpctrl for SSD201/SSD202D
ARM: mstar: Add smp ctrl registers to infinity2m dtsi
ARM: mstar: Add dts for Honestar ssd201htv2
ARM: mstar: Add chip level dtsi for SSD202D
ARM: mstar: Add common dtsi for SSD201/SSD202D
ARM: mstar: Add infinity2m support
dt-bindings: mstar: Add Honestar SSD201_HT_V2 to mstar boards
dt-bindings: vendor-prefixes: Add honestar vendor prefix
dt-bindings: mstar: Add binding details for mstar,smpctrl
ARM: mstar: Fill in GPIO controller properties for infinity
ARM: mstar: Add gpio controller to MStar base dtsi
ARM: zynq: Fix incorrect reference to XM013 instead of XM011
ARM: zynq: Convert at25 binding to new description on zc770-xm013
ARM: zynq: Fix OCM mapping to be aligned with binding on zc702
ARM: zynq: Fix leds subnode name for zc702/zybo-z7
ARM: zynq: Rename bus to be align with simple-bus yaml
...
Pull devicetree updates from Rob Herring:
- Add vendor prefixes for bm, gpio-key, mentor, FII, and Ampere
- Add ADP5585/ADP5589 and delta,q54sj108a2 to trivial-devices.yaml
- Convert fixed-partitions, i2c-gate and fsl,dpaa2-console bindings to
schemas
- Drop PicoXcell bindings
- Drop unused and undocumented 'pnx,timeout' property from LPC32xx
- Add 'dynamic-power-coefficient' to Mali GPU bindings
- Make 'make dt_binding_check' not error out on warnings
- Various minor binding fixes
* tag 'devicetree-for-5.11' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (22 commits)
dt-bindings: mali-bifrost: Add dynamic-power-coefficient
dt-bindings: mali-midgard: Add dynamic-power-coefficient
dt-bindings: i2c: dw: cancel mandatory requirements for "#address-cells" and "#size-cells"
dt-bindings: Remove PicoXcell bindings
ARM: dts: lpc32xx: Remove unused and undocumented 'pnx,timeout'
dt-bindings: mtd: convert "fixed-partitions" to the json-schema
dt-bindings: vendor-prefixes: Add undocumented bm, gpio-key, and mentor prefixes
dt-bindings: pci: rcar-pci-ep: Document missing interrupts property
dt-bindings: vendor-prefixes: Add an entry for AmpereComputing.com
dt-bindings: vendor-prefixes: correct the spelling of TQ-Systems GmbH
dt-bindings: mfd: fix stm32 timers example
dt-bindings: trivial-devices: Add delta,q54sj108a2
dt-bindings:i2c:i2c-gate: txt to yaml conversion
dt-bindings: add ADP5585/ADP5589 entries to trivial-devices
dt-bindings: Correct GV11B GPU register sizes
dt-bindings: vendor-prefixes: Add FII
dt-bindings: Fix typo on the DesignWare IP reset bindings documentation
dt-bindings: Fix error in 'make dtbs_check' when using DT_SCHEMA_FILES
dt-bindings: arm: vt8500: remove redundant white-spaces
dt-bindings: fsl-imx-drm: fix example compatible string
...
Pull input updates from Dmitry Torokhov:
- support for inhibiting input devices at request from userspace. If a
device implements open/close methods, it can also put device into low
power state. This is needed, for example, to disable keyboard and
touchpad on convertibles when they are transitioned into tablet mode
- now that ordinary input devices can be configured for polling mode,
dedicated input polling device implementation has been removed
- GTCO tablet driver has been removed, as it used problematic custom
HID parser, devices are EOL, and there is no interest from the
manufacturer
- a new driver for Dialog DA7280 haptic chips has been introduced
- a new driver for power button on Dell Wyse 3020
- support for eKTF2132 in ektf2127 driver
- support for SC2721 and SC2730 in sc27xx-vibra driver
- enhancements for Atmel touchscreens, AD7846 touchscreens, Elan
touchpads, ADP5589, ST1232 touchscreen, TM2 touchkey drivers
- fixes and cleanups to allow clean builds with W=1
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (86 commits)
Input: da7280 - fix spelling mistake "sequemce" -> "sequence"
Input: cyapa_gen6 - fix out-of-bounds stack access
Input: sc27xx - add support for sc2730 and sc2721
dt-bindings: input: Add compatible string for SC2721 and SC2730
dt-bindings: input: Convert sc27xx-vibra.txt to json-schema
Input: stmpe - add axis inversion and swapping capability
Input: adp5589-keys - do not explicitly control IRQ for wakeup
Input: adp5589-keys - do not unconditionally configure as wakeup source
Input: ipx4xx-beeper - convert comma to semicolon
Input: parkbd - convert comma to semicolon
Input: new da7280 haptic driver
dt-bindings: input: Add document bindings for DA7280
MAINTAINERS: da7280 updates to the Dialog Semiconductor search terms
Input: elantech - fix protocol errors for some trackpoints in SMBus mode
Input: elan_i2c - add new trackpoint report type 0x5F
Input: elants - document some registers and values
Input: atmel_mxt_ts - simplify the return expression of mxt_send_bootloader_cmd()
Input: imx_keypad - add COMPILE_TEST support
Input: applespi - use new structure for SPI transfer delays
Input: synaptics-rmi4 - use new structure for SPI transfer delays
...
Pull EDAC updates from Borislav Petkov:
"Somewhat busier than usual this cycle:
- Add support for AST2400 and AST2600 hw to aspeed_edac (Troy Lee)
- Remove an orphaned mv64x60_edac driver. Good riddance (Michael
Ellerman)
- Add a new igen6 driver for Intel client SoCs with an integrated
memory controller and using in-band ECC (Qiuxu Zhuo and Tony Luck)
- The usual smattering of fixes and cleanups all over"
* tag 'edac_updates_for_v5.11' of git://git.kernel.org/pub/scm/linux/kernel/git/ras/ras:
EDAC/mv64x60: Remove orphan mv64x60 driver
EDAC/aspeed: Add support for AST2400 and AST2600
ARM: dts: aspeed: Add AST2600 EDAC into common devicetree
dt-bindings: edac: aspeed-sdram-edac: Add ast2400/ast2600 support
EDAC/amd64: Fix PCI component registration
EDAC/igen6: ecclog_llist can be static
EDAC/i10nm: Add Intel Sapphire Rapids server support
EDAC: Add DDR5 new memory type
EDAC/i10nm: Use readl() to access MMIO registers
MAINTAINERS: Add entry for Intel IGEN6 EDAC driver
EDAC/igen6: Add debugfs interface for Intel client SoC EDAC driver
EDAC/igen6: Add EDAC driver for Intel client SoCs using IBECC
EDAC/synopsys: Return the correct value in mc_probe()
MAINTAINERS: Clean up the F: entries for some EDAC drivers
EDAC: Add three new memory types
EDAC: Fix some kernel-doc markups
EDAC: Do not issue useless debug statements in the polling routine
EDAC/amd64: Remove unneeded breaks
Few regression fixes for omaps for v5.10
Few fixes for regression issues recently noticed by folks testing
the current kernel:
- We need to disable AES for n950 as it's not accessible because of the
secure mode configuration and kernel fails to boot
- On gta04 wlan probe exposed a bug for BUS_NOTIFY_BIND_DRIVER that has
been around for a long time
- Droid bionic exposed an issue where we configure an invalid range on
the PMIC that adds boot time warnings
Obviously these fixes can be merged whenever suitable.
* tag 'omap-for-v5.10/fixes-rc6-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: omap2: pmic-cpcap: fix maximum voltage to be consistent with defaults on xt875
ARM: OMAP2+: omap_device: fix idling of devices during probe
ARM: dts: OMAP3: disable AES on N950/N9
Link: https://lore.kernel.org/r/pull-1607674932-973902@atomide.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The check_spi_bus_bridge() in scripts/dtc/checks.c requires that the node
have "spi-slave" property must with "#address-cells = <0>" and
"#size-cells = <0>". But currently both "#address-cells" and "#size-cells"
properties are deleted, the corresponding default values are 2 and 1. As a
result, the check fails and below warnings is displayed.
arch/arm/boot/dts/mmp2.dtsi:472.23-480.6: Warning (spi_bus_bridge): \
/soc/apb@d4000000/spi@d4037000: incorrect #address-cells for SPI bus
also defined at arch/arm/boot/dts/mmp2-olpc-xo-1-75.dts:225.7-237.3
arch/arm/boot/dts/mmp2.dtsi:472.23-480.6: Warning (spi_bus_bridge): \
/soc/apb@d4000000/spi@d4037000: incorrect #size-cells for SPI bus
also defined at arch/arm/boot/dts/mmp2-olpc-xo-1-75.dts:225.7-237.3
arch/arm/boot/dts/mmp2-olpc-xo-1-75.dtb: Warning (spi_bus_reg): \
Failed prerequisite 'spi_bus_bridge'
Because the value of "#size-cells" is already defined as zero in the node
"ssp3: spi@d4037000" in arch/arm/boot/dts/mmp2.dtsi. So we only need to
explicitly add "#address-cells = <0>" and keep "#size-cells" no change.
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Link: https://lore.kernel.org/r/20201207084752.1665-2-thunder.leizhen@huawei.com'
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
ARM: dts: zynq: DT changes for v5.11
- Adding support for Zturn-v5
- Small DT changes to clean errors from dt_binding_check
* tag 'zynq-dt-for-v5.10' of https://github.com/Xilinx/linux-xlnx:
ARM: zynq: Fix incorrect reference to XM013 instead of XM011
ARM: zynq: Convert at25 binding to new description on zc770-xm013
ARM: zynq: Fix OCM mapping to be aligned with binding on zc702
ARM: zynq: Fix leds subnode name for zc702/zybo-z7
ARM: zynq: Rename bus to be align with simple-bus yaml
ARM: zynq: Fix compatible string for adi,adxl345 chip
ARM: zynq: Add Z-turn board V5
ASPEED device tree updates for 5.11
- New machines
* Bytedance G220A, an AST2500 BMC for an x86 server
* Facebook Galaxy100, an AST2400 BMC for a network switch
* IBM Rainier 4U, an AST2600 BMC for a PowerPC server
- Reworking of Facebook device trees to use common dtsi
- A 64MB flash layout used by the G220A
- Misc updates to tiogapass, ethanolx, s2600wf, tacoma and rainier
* tag 'aspeed-5.11-devicetree' of git://git.kernel.org/pub/scm/linux/kernel/git/joel/aspeed: (25 commits)
ARM: dts: aspeed: ast2600evb: Add MAC0
ARM: dts: aspeed: rainier: Don't shout addresses
ARM: dts: aspeed: rainier: Mark FSI SPI controllers as restricted
ARM: dts: tacoma: Add reserved memory for ramoops
ARM: dts: rainier: Add reserved memory for ramoops
ARM: dts: tacoma: Fix node vs reg mismatch for flash memory
ARM: dts: aspeed: rainier: Add 4U device-tree
arm: dts: aspeed: tiogapass: Enable second MAC
ARM: dts: aspeed: minipack: Fixup I2C tree
ARM: dts: aspeed: wedge400: Fix FMC flash0 layout
ARM: dts: aspeed: Add Facebook Galaxy100 (AST2400) BMC
ARM: dts: aspeed: wedge100: Use common dtsi
ARM: dts: aspeed: wedge40: Use common dtsi
ARM: dts: aspeed: Common dtsi for Facebook AST2400 Network BMCs
ARM: dts: aspeed: amd-ethanolx: Add GPIO line names
ARM: dts: aspeed: amd-ethanolx: Enable devices for the iKVM functionality
ARM: dts: aspeed: amd-ethanolx: Enable KCS channel 3
ARM: dts: aspeed: tiogapass: Remove vuart
ARM: dts: Fix label address for 64MiB OpenBMC flash layout
ARM: dts: aspeed: g220a: Add some gpios
...
Link: https://lore.kernel.org/r/CACPK8Xfd7AmuEaUdFfYLu4ktcrpTnYUgwQSxUbC-McB02hvo_g@mail.gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
