Because that is what you get if a BIO_RW_BARRIER isn't supported!
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
We need to hold a reference to rdevs while reading and writing to attempt to
correct read errors. This reference must be taken under an rcu lock.
Signed-off-by: Neil Brown <neilb@suse.de>
Cc: "Paul E. McKenney" <paulmck@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
We should add to the counter for the rdev *after* checking if the rdev is
NULL!!!
Signed-off-by: Neil Brown <neilb@suse.de>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Names that are the opposite of their intended meanings are not so helpful.
Signed-off-by: Bryan O'Sullivan <bos@pathscale.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The reset code now turns off the PRESENT flag during a reset, so that
other code won't attempt to access a device that's in mid-reset.
Signed-off-by: Bryan O'Sullivan <bos@pathscale.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Remember when the verbs layer unregisters from the lower-level code.
Signed-off-by: Bryan O'Sullivan <bos@pathscale.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Different ipath hardware types have different numbers of buffers
available, so we decide on the counts ourselves unless we are specifically
overridden with a module parameter.
Signed-off-by: Bryan O'Sullivan <bos@pathscale.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Some systems do not set up 64-bit maps on systems with 2GB or less of
memory installed, so we have to fall back to trying a 32-bit setup.
Signed-off-by: Bryan O'Sullivan <bos@pathscale.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
We were accidentally exposing the "reset" sysfs file more than once
per device.
Signed-off-by: Bryan O'Sullivan <bos@pathscale.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
GuidInfo records have 8 byte GUIDs in them, so an index should be
multiplied by 8 to get an offset. mthca_query_gid() was incorrectly
multiplying by 16.
Noticed by Leonid Keller <leonid@mellanox.co.il>.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
* master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6:
[TG3]: Update version and reldate
[TG3]: Fix bug in nvram write
[TG3]: Add reset_phy parameter to chip reset functions
[TG3]: Reset chip when changing MAC address
[TG3]: Add phy workaround
[TG3]: Call netif_carrier_off() during phy reset
[IPV6]: Fix race in route selection.
[XFRM]: fix incorrect xfrm_policy_afinfo_lock use
[XFRM]: fix incorrect xfrm_state_afinfo_lock use
[TCP]: Fix unlikely usage in tcp_transmit_skb()
[XFRM]: fix softirq-unsafe xfrm typemap->lock use
[IPSEC]: Fix IP ID selection
[NET]: use hlist_unhashed()
[IPV4]: inet_init() -> fs_initcall
[NETLINK]: cleanup unused macro in net/netlink/af_netlink.c
[PKT_SCHED] netem: fix loss
[X25]: fix for spinlock recurse and spinlock lockup with timer handler
* git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: make EVIOCGSND return meaningful data
Input: ressurect EVIOCGREP and EVIOCSREP
Input: psmouse - fix new device detection logic
Input: move input_device_id to mod_devicetable.h
Input: allow using several chords for braille
Input: allow passing NULL to input_free_device()
Input: spitzkbd - fix the reversed Address and Calender keys
Input: ads7846 - improve filtering for thumb press accuracy
Input: ads7846 - report 0 pressure value along with pen up event
Input: ads7846 - handle IRQs that were latched during disabled IRQs
Input: ads7846 - miscellaneous fixes
Input: ads7846 - use msleep() instead of udelay() in suspend
Input: ads7846 - debouncing and rudimentary sample filtering
Input: ads7846 - power down ADC a bit later
Input: ads7846 - add pen_down sysfs attribute
Input: wistron - add support for Fujitsu N3510
Input: wistron - add signature for Amilo M7400
* git://git.kernel.org/pub/scm/linux/kernel/git/perex/alsa: (22 commits)
[ALSA] via82xx - Use DXS_SRC as default for VIA8235/8237/8251 chips
[ALSA] hda-codec - Add model entry for ASUS Z62F
[ALSA] PCMCIA sound devices shouldn't depend on ISA
[ALSA] hda-codec - Fix capture from line-in on VAIO SZ/FE laptops
[ALSA] Fix Oops at rmmod with CONFIG_SND_VERBOSE_PROCFS=n
[ALSA] PCM core - introduce CONFIG_SND_PCM_XRUN_DEBUG
[ALSA] adding __devinitdata to pci_device_id
[ALSA] add __devinitdata to all pci_device_id
[ALSA] hda-codec - Add codec id for AD1988B codec chip
[ALSA] hda-codec - Add model entry for ASUS M9 laptop
[ALSA] pcxhr - Fix a compiler warning on 64bit architectures
[ALSA] via82xx: tweak VT8251 workaround
[ALSA] intel8x0 - Disable ALI5455 SPDIF-input
[ALSA] via82xx: add support for VIA VT8251 (AC'97)
[ALSA] Fix typos and add information about Jack support to Audiophile-Usb.txt
[ALSA] Fix double free in error path of miro driver
[ALSA] hda-codec - Add entry for Epox EP-5LDA+ GLi
[ALSA] sound/pci/: remove duplicate #include's
[ALSA] hda-codec - Use model 'hp' for all HP laptops with AD1981HD
[ALSA] continue on IS_ERR from platform device registration
...
Jan Engelhardt <jengelh@linux01.gwdg.de> wrote:
while compiling 2.6.17-rc2 with allyesconfig, this showed up:
...
LOGO drivers/video/logo/logo_superh_clut224.c
CC drivers/video/logo/logo_linux_mono.o
...
A tab had sneaked in. Convert it to a few spaces.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Patch from Pavel Pisa
The clock starting imxmci_start_clock() function contains hardware
issue workaround, which repeats start attempt, if SDHC does not react on
the first trial. But the second start attempt can be taken even, if the
first succeed and test code misses time limited clock running phase
due to delay caused by schedule to other task or some another device
interrupt. This change enables to detect such situation.
The performance is not issue, because usually at full clock rate
only about six loops in delay cycle are needed.
Signed-off-by: Pavel Pisa <pisa@cmp.felk.cvut.cz>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Markus Gutschke
In order to prevent gcc from making incorrect optimizations, all asm()
statements that define system calls should report memory as
clobbered. Recent versions of the headers for i386 have been changed
accordingly, but the ARM headers are still defective.
This patch fixes the bug tracked at
http://bugzilla.kernel.org/show_bug.cgi?id=6205
Signed-off-by: Markus Gutschke <markus@google.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
A bug report from Gerd Hoffmann has highlighted that unconditionally
enabling the transmit interrupt at the end of console writes is very
bad.
In Gerd's case, it causes the test for buggy UARTs to give false
positives, incorrectly identifying ports as buggy when they are not.
Moreover, if we unconditionally enable the interrupt, and the port
is sharing it's interrupt with other ports, there is the very real
possibility that we'll cause an interrupt storm. (Not all ports use
OUT2 as an interrupt mask.)
Hence, revert part of f91a3715db and
all of f5968b37b3 until a better solution
can be found.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Alchemy SoC uart have got a non-standard divisor register that needs some
special handling.
This patch adds divisor read/write functions with test and special
handling for Alchemy internal uart.
Signed-off-by: Jon Anders Haugum <jonah@omegav.ntnu.no>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
I've noticed that the 8250/Au1x00 driver (drivers/serial/8250_au1x00.c)
doesn't claim UART memory ranges and uses wrong (KSEG1-based) UART
addresses instead of the physical ones.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The locking for the uart_port is over complicated, and can be
simplified if we introduce a flag to indicate that a port is "dead"
and will be removed.
This also helps the validator because it removes a case of non-nested
unlock ordering.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Fix bug in nvram write function. If the starting nvram address offset
happens to be the last dword of the page, the NVRAM_CMD_LAST bit will
not get set in the existing code. This patch fixes the bug by changing
the "else if" to "if" so that the last dword condition always gets
checked.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a reset_phy parameter to tg3_reset_hw() and tg3_init_hw(). With
the full chip reset during MAC address change, the automatic PHY reset
during chip reset will cause a link down and bonding will not work
properly as a result. With this reset_phy parameter, we can do a chip
reset without link down when changing MAC address or MTU.
Signed-off-by: Gary Zambrano <zambrano@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Do the full chip reset when changing MAC address if ASF is enabled.
ASF sometimes uses a different MAC address than the driver. Without
the reset, the ASF MAC address may be overwritten when the driver's
MAC address is changed.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add some PHY workaround code to reduce jitter on some PHYs.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add netif_carrier_off() call during tg3_phy_reset(). This is needed
to properly track the netif_carrier state in cases where we do a
PHY reset with interrupts disabled. The SerDes code will not run
properly if the netif_carrier state is wrong.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Let people enable the advansys driver on x86-32, even though it's broken
on other architectures due to missing DMA mapping infrastructure.
It's used by Jeffrey Phillips Freeman <jeffreyfreeman@syncleus.com> and
possibly others.
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
While writing to an event device allows to set repeat rate for an
individual input device there is no way to retrieve current settings
so we need to ressurect EVIOCGREP. Also ressurect EVIOCSREP so we
have a symmetrical interface.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Add help text in Kconfig
Signed-off-by: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Generate new sysfs-attribute 'uid' that contains an device specific unique
identifier. This can be used to identity multiple ALIASES of the same
physical device (PAV). In addition the sysfs-attributes 'vendor' (containing
the manufacturer of the device) and 'alias' (identify alias or base device) is
added. This is first part of PAV support in LPAR (also valid on zVM).
Signed-off-by: Horst Hummel <horst.hummel@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
In case of an instruction processing damage (IPD) machine check in kernel mode
the resulting action is always to stop the kernel. This is not necessarily
the best solution since a retry of the failing instruction might succeed. Add
logic to retry the instruction if no more than 30 instruction processing
damage checks occured in the last 5 minutes.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Added some changes that where proposed by Andrew Morton. Added 3592 device
type.
Signed-off-by: Stefan Bader <shbader@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
With CONFIG_SLAB_DEBUG=y networking over qeth doesn't work. The problem is
that the qib structure embedded in the qeth_irq structure needs an alignment
of 256 but kmalloc only guarantees an alignment of 8. When using SLAB
debugging the alignment of qeth_irq is not sufficient for the embedded qib
structure which causes all users of qdio (qeth and zfcp) to stop working.
Allocate qeth_irq structure with __get_free_page. That wastes a small amount
of memory (~2500 bytes) per online adapter.
Signed-off-by: Christian Borntraeger <cborntra@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The dasd state machine is not designed to enable an unformatted device, since
'unformatted' is a final state. The BIODASDENABLE ioctl calls
dasd_enable_device() which never returns if the device is in this special
state. Return -EPERM in dasd_increase_state for unformatted devices to make
dasd_enable_device terminate. Note: To get such an unformatted device online
it has to be re-analyzed. This means that the device needs to be disabled
prior to re-enablement.
Signed-off-by: Horst Hummel <horst.hummel@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Avoid memory allocation with GFP_KERNEL in qdio_establish/qdio_shutdown. Use
memory pool instead. (Otherwise this can lead to an I/O stall where qdio
waits for a free page and zfcp waits for end of error recovery in low memory
situations.)
Signed-off-by: Andreas Herrmann <aherrman@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Interrupts can stay disabled if an error occurred in _chp_add(). Use
spin_unlock_irq on the error paths to reenable interrupts.
Signed-off-by: Stefan Bader <shbader@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix a race condition in the I/O termination logic. The race can cause I/O to
a dasd device to fail with no retry left after turning one channel path to the
device off and on multiple times.
Signed-off-by: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
this fixes coverity id #489.
Since the last element in the array is always ARRAY_SIZE-1 we have to check
for ipcnum >= ARRAY_SIZE()
Signed-off-by: Eric Sesterhenn <snakebyte@gmx.de>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
If compiled into the kernel, parport_register_driver() is called before the
parport driver has been initalised.
This means that it is expected that tp_count is 0 after the
parport_register_driver() call() - tipar's attach function will not be
called until later during bootup.
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- Add new SA_PROBEIRQ which suppresses the new sharing-mismatch warning.
Some drivers like to use request_irq() to find an unused interrupt slot.
- Use it in i82365.c
- Kill unused SA_PROBE.
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Current address translation methods can produce wrong results, because
virt_to_bus and vice versa may not produce correct offsets on dma-allocated
memory. The right way is, while tracking both phys and virt address of the
window that has been allocated for boffer descriptors, and use those
numbers to compute the offset and make translation properly.
Signed-off-by: Vitaly Bordug <vbordug@ru.mvista.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This is intended to make the driver code more generic and flexible,
to get rid of board-specific layouts within driver, and generic rehaul,
yet keeping compatibility with the existing stuff utilizing it, being
compatible with legacy behavior (but with complaints that legacy mode
used).
Signed-off-by: Vitaly Bordug <vbordug@ru.mvista.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Some people report that we die on some Macs when we are expecting to
catch machine checks after poking at some random I/O address. I'd seen
it happen on my dual G4 with serial ports until we fixed those to use
OF, but now other users are reporting it with i8042.
This expands the use of check_legacy_ioport() to avoid that situation
even on 32-bit kernels.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux-2.6:
[IA64] update sn2 defconfig
[IA64] Add mca recovery failure messages
[IA64-SGI] fix SGI Altix tioce_reserve_m32() bug
[IA64] enable dumps to capture second page of kernel stack
[IA64-SGI] - Reduce overhead of reading sn_topology
[IA64-SGI] - Fix discover of nearest cpu node to IO node
[IA64] IOC4 config option ordering
[IA64] Setup an IA64 specific reclaim distance
[IA64] eliminate compile time warnings
[IA64] eliminate compile time warnings
[IA64-SGI] SN SAL call to inject memory errors
[IA64] - Fix MAX_PXM_DOMAINS for systems with > 256 nodes
[IA64] Remove unused variable in sn_sal.h
[IA64] Remove redundant NULL checks before kfree
[IA64] wire up compat_sys_adjtimex()
Fix the driver to return SUCCESS if the firmware or driver doesn't
have a command to abort, i.e., it's already been returned. Without
this patch, error recovery will take the target offline as it tries
harder and harder to get the driver to return the command it no longer
has.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
* master.kernel.org:/pub/scm/linux/kernel/git/gregkh/pci-2.6:
[PATCH] PCI quirk: VIA IRQ fixup should only run for VIA southbridges
[PATCH] PCI: fix potential resource leak in drivers/pci/msi.c
[PATCH] PCI: Documentation: no more device ids
[PATCH] PCI: fix via irq SATA patch
* master.kernel.org:/pub/scm/linux/kernel/git/gregkh/usb-2.6:
[PATCH] USB: ftdi_sio: add support for ASK RDR 400 series card reader
[PATCH] USB: ftdi_sio: Adds support for iPlus device.
[PATCH] USB: ftdi_sio vendor code for RR-CirKits LocoBuffer USB
[PATCH] USB: Use new PCI_CLASS_SERIAL_USB_* defines
[PATCH] USB: net2280: set driver data before it is used
[PATCH] USB: net2280: check for shared IRQs
[PATCH] USB: net2280: send 0-length packets for ep0
[PATCH] USB: net2280: Handle STALLs for 0-length control-IN requests
[PATCH] USB: storage: atmel unusual dev update
[PATCH] USB: Storage: unusual devs update
[PATCH] USB: add new iTegno usb CDMA 1x card support for pl2303
[PATCH] USB: Resource leak fix for whiteheat driver
Alan Cox pointed out that the VIA 'IRQ fixup' was erroneously running
on my system which has no VIA southbridge (but I do have a VIA IEEE
1394 device).
This should address that. I also changed "Via IRQ" to "VIA IRQ"
(initially I read Via as a capitalized via (by way/means of).
Signed-off-by: Chris Wedgwood <cw@f00f.org>
Acked-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The coverity checker spotted (as entry #599) that we might leak `entry' in
drivers/pci/msi.c::msix_capability_init()
This patch should take care of that.
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When abort failed, the driver gets reset handleer called. In the reset
handler, driver calls 'scsi_done()' callback for same SCSI command packet
(struct scsi_cmnd) multiple times if there are multiple SCSI command packet
in the pend_list. More over, if there are entry in the pend_lsit with
IOCTL packet associated, the driver returns it to wrong free_list so that,
in turn, the driver could end up with 'NULL pointer dereference..' during
I/O command building with incorrect resource.
Also, the patch contains several minor/cosmetic changes besides this.
Signed-off-by: Seokmann Ju <seokmann.ju@lsil.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Bug fix for stack overflow in EventDescriptionStr, (a function
for debuging firmware events). We allocated 50 bytes on local stack
for buff[], however there are places in the code where we've attempted
copying in greater than 50 bytes into buff[].
Signed-off-by: Eric Moore <Eric.Moore@lsil.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Some versions of the IBM 2104-DU3 disk enclosure
have been observed to hang Inquiries to non zero
LUNs to the SES device. This device only has LUN 0,
so this patch adds it to the BLIST to prevent scsi
core from scanning beyond LUN 0.
Signed-off-by: Brian King <brking@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Some pioneer DVDs are apparently returning odd "not ready" status
codes that the mid-layer doesn't recognise and so passes back to the
user as errors.
This patch overhauls our not-ready handling and adds transparent retries for:
format in progress
rebuild in progress
recalculation in progress
operation in progress
Long write in progress
self test in progress
The Pioneer was actually returning "long write in progress"
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This patch adds support for an ASK RDR 400 series contactless card
reader <http://www.ask.fr/uk/products_and_services/terminals.html> to
the ftdi_sio driver's device ID table. The product ID was supplied by
Adriano Couto on the ftdi-usb-sio-devel list.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Adds support in ftdi_sio usbserial driver for USB modems sold by
Plus GSM Company in Poland.
Signed-off-by: Luiz Fernando Capitulino <lcapitulino@mandriva.com.br>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds recognition of the RR-CirKits LocoBuffer USB
to the existing FTDI driver. http://www.rr-cirkits.com
Signed-off-by: Nathan Bronson <ngb@sns-usa.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We could use the recently added PCI_CLASS_SERIAL_USB_UHCI,
PCI_CLASS_SERIAL_USB_OHCI and PCI_CLASS_SERIAL_USB_EHCI defines in
more places, for slightly shorter and clearer code.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as671) fixes a bug in the error pathway for the net2280
probe routine. A failure during probe will cause the driver to call
pci_get_drvdata before the corresponding pci_set_drvdata has been set.
The patch also does a kzalloc conversion.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as670) adds a check for whether a shared IRQ was actually
generated by the net2280 device.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as669) fixes a bug in the net2280 driver. Now it will
properly send zero-length packets on ep0 until the control status stage
occurs.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as668) fixes a typo in net2280. The handler for 0-length
control-IN requests should check that the endpoint _isn't_ halted before
sending a 0-length packet.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Originally submitted by Olivier Blondeau <zeitoun@gmail.com>, with re-diffing
by me. Adds a new atmel unusual_dev entry.
Signed-off-by: Phil Dibowitz <phil@ipom.com>
This patch removes the Protocol portion of the Iomega Click! device as it's not
needed. Not-needed message reported by Kenneth Crudup <kenny@panix.com>
Signed-off-by: Phil Dibowitz <phil@ipom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add new iTegno usb CDMA 1x card (usbid '0eba:2080') support to pl2303 driver
Signed-off-by: Wang Jun <wangjun1974@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We may return from drivers/usb/serial/whiteheat.c::whiteheat_attach()
without freeing `result' if we leave via the no_firmware: label.
Spotted by the coverity checker as #670
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Few of the notifier_chain_register() callers use __init in the definition
of notifier_call. It is incorrect as the function definition should be
available after the initializations (they do not unregister them during
initializations).
This patch fixes all such usages to _not_ have the notifier_call __init
section.
Signed-off-by: Chandra Seetharaman <sekharan@us.ibm.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch fixes the nic initialization. If the nic was in low power
mode, it brings it back to normal power. Also, it utilizes a new
hardware reset during the init.
I am resending based on feedback, I corrected the register size mapping
and delay after posted write.
Signed-Off-By: Ayaz Abdulla <aabdulla@nvidia.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The sky2_reset function only called from sky2_probe.
Maybe the compiler was smart enough to figure this out already.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The ALIGN() macro in kernel.h does the same math that the
sky2 driver was using for padding.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Add an fake NAPI schedule once a second. This is an attempt to work around
for broken configurations with edge-triggered interrupts.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This is a workaround for the case edge-triggered irq's. Several users
seem to have broken configurations sharing edge-triggered irq's. To avoid
losing IRQ's, reshedule if more work arrives.
The changes to netdevice.h are to extract the part that puts device
back in list into separate inline.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Update skb with the real packet size.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
For coping with bad keyboards, permit to type a braille pattern by
pressing several chords. By default, only one chord is needed.
Signed-off-by: Samuel Thibault <samuel.thibault@ens-lyon.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Providing more accurate coordinates for thumb press requires additional
steps in the filtering logic:
- Ignore samples found invalid by the debouncing logic, or the ones that
have out of bound pressure value.
- Add a parameter to repeat debouncing, so that more then two consecutive
good readings are required for a valid sample.
Signed-off-by: Imre Deak <imre.deak@nokia.com>
Acked-by: Juha Yrjola <juha.yrjola@nokia.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
X touchscreen drivers that don't interpret the designated pen up message
assume a pen up event from a pressure value 0. For these we generate a
pressure 0 message along with the pen up message.
Signed-off-by: Imre Deak <imre.deak@nokia.com>
Acked-by: Juha Yrjola <juha.yrjola@nokia.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Fix resource leak in
drivers/scsi/aic7xxx/aic7xxx_osm_pci.c::ahc_linux_pci_dev_probe()
Found by the coverity checker (#668)
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
mptbase.h
bump version number to 3.03.09
remove unneeded flags
define workq and remove old fc specific locks
mptbase.c
initialize new lock and don't initialize two removed locks
mptscsih.c
when firmware reports target is no longer there, return
DID_REQUEUE for fc hosts so that i/o doesn't get killed until
the transport has an opportunity to manage the loss via its
dev loss timer
when the "eh_abort" routine is called, check to see if the
driver has the command or not before looking to see if a reset
is pending. James Smart and I talked about this and believe
that the API for this routine is: if driver doesn't have
command, return SUCCESS. This change helps prevent a target
from being taken offline. SUCCESS is returned because it's
likely that the command completed after error recovery timed
it out but before it could be aborted.
provide a routine to queue work to newly created workq, and
use it.
remove "ioc" from mptscsih_abort() it was only used one time.
the other references were via hd->ioc, so I just moved it....
net change in references to ioc via hd->ioc is zero
move hd->resetPending test and hd->timeouts increment to after
the test for whether the command to be aborted remains known
to the driver
Make certain that the workq exists before queuing work to it.
mptfc.c
no longer need to lock rport data structures as I was able to
single thread the code! I fixed up the debug code to
eliminate compilation messages due to type mismatch in the
printk. Got rid of some no longer needed rport flags.
Initialize and destroy the workq used for the rescan work.
simplify the logic regarding the increment of
fc_rescan_work_count. use post increment and test for zero
vs. pre increment and test for one; eliminate work_count
variable: queue_work can be called with the work_lock held as
it doesn't sleep
Signed-off-by: Michael Reed <mdr@sgi.com>
Signed-off-by: Eric Moore <Eric.Moore@lsil.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This patch handles case where raid hidden components
are not being removed when power turned off to device
attached to expander, as well as the case of
exposing raid components when power is turned back on
to devices attached to an expander. (This is a repost
of this patch, with mptsas_is_end_device declared
further up in the code.)
This patch contains some other miscellaneous bug fix's.
Signed-off-by: Eric Moore <Eric.Moore@lsil.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This patch fixes PIO mode on the softmac bcm43xx
driver. (A dscape patch will follow).
It mainly fixes endianess issues.
This patch is tested on PowerPC32 and i386.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The original code was doing arithmetics on a little-endian value.
Reported by Stelios Koroneos <stelios@stelioscellar.com>
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The MMC layer gives us two parts for the timeout calculation - a fixed
timeout in nanoseconds, and a card clock-speed dependent part.
The PXA MMC hardware allows for a timeout based on the fixed host clock
speed only. This resulted in some cards being given a short timeout,
and therefore failing to work.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* git://git.kernel.org/pub/scm/linux/kernel/git/kyle/parisc-2.6:
[PARISC] MAINTAINERS
[PARISC] Make ioremap default to _nocache
[PARISC] Add new entries to the syscall table
[PARISC] Further work for multiple page sizes
[PARISC] Fix up hil_kbd.c mismerge
[PARISC] defconfig updates
[PARISC] Document that we tolerate "Relaxed Ordering"
[PARISC] Misc. janitorial work
[PARISC] EISA regions must be mapped NO_CACHE
[PARISC] OSS ad1889: Match register names with ALSA driver
* git://git.kernel.org/pub/scm/linux/kernel/git/brodo/pcmcia-fixes-2.6:
[PATCH] pcmcia/pcmcia_resource.c: fix crash when using Cardbus cards
[PATCH] vrc4171: update config
[PATCH] pcmcia: fix oops in static mapping case
[PATCH] pcmcia: remove unneeded forward declarations
[PATCH] pcmcia: do not set dev_node to NULL too early
[PATCH] pcmcia: fix comment for pcmcia_load_firmware
[PATCH] pcmcia: unload second device first
[PATCH] pcmcia: add new ID to pcnet_cs
* git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc-merge:
powerpc: Fix define_machine so machine_is() works from modules
powerpc/ppc: export strncasecmp
[PATCH] powerpc: fix oops in alsa powermac driver
[PATCH] powerpc: update {g5,iseries,pseries}_defconfigs
[PATCH] ppc: Fix powersave code on arch/ppc
[PATCH] powerpc/cell: remove BUILD_BUG_ON and add sys_tee to spu_syscall_table
[PATCH] powermac: Fix i2c on keywest based chips
[PATCH] powerpc: Lower threshold for DART enablement to 1GB
[PATCH] powerpc: IOMMU support for honoring dma_mask
This patch contains the following possible cleanups:
- make the following needlessly global function static:
- drm_bufs.c: drm_addbufs_fb()
- remove the following unused EXPORT_SYMBOL's:
- drm_agpsupport.c: drm_agp_bind_memory
- drm_bufs.c: drm_rmmap_locked
- drm_bufs.c: drm_rmmap
- drm_stub.c: drm_get_dev
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Dave Airlie <airlied@linux.ie>
I recently found that not all BIOS manufacturers are using the specified
generic PNP id in their TPM ACPI table entry. I have added the vendor
specific IDs that I know about and added a module parameter that a user can
specify another HID to the probe list if their device isn't being found by the
default list.
Signed-off-by: Kylene Hall <kjhall@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch adds a boolean module parameter that allows the user to turn
interrupt support on and off. The default behavior is to attempt to use
interrupts.
Signed-off-by: Kylene Hall <kjhall@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Use __devexit_p() for the exit/remove function to protect against
discarding it.
WARNING: drivers/char/tpm/tpm_infineon.o - Section mismatch: reference to .exit.text:tpm_inf_pnp_remove from .data between 'tpm_inf_pnp' (at offset 0x20) and 'tpm_inf'
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Cc: Kylene Jo Hall <kjhall@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The acpi table which contains the BIOS log events was updated for 1.2.
There are now client and server modes as defined in the specifications with
slightly different formats. Additionally, the start field was even too
small for the 1.1 version but had been working anyway. This patch updates
the code to deal with any of the three types of headers probperly (1.1, 1.2
client and 1.2 server).
Signed-off-by: Kylie Hall <kjhall@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The memory start and length values obtained from the ACPI entry need to be
checked and filled in with the default values from the specification if
they don't exist. This patch fills in the default values and uses them
appropriately.
Signed-off-by: Kylie Hall <kjhall@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Apply the latest changes in the TPM interface to the Infineon TPM-driver.
Signed-off-by: Marcel Selhorst <selhorst@crypto.rub.de>
Acked-by: Kylie Hall <kjhall@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Use set_bit() and clear_bit() for dev_mask manipulation.
Signed-off-by: Kylie Hall <kjhall@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The timeout and duration values used in the tpm driver are not exposed to
userspace. This patch converts the storage units to jiffies with
msecs_to_jiffies. They were always being used in jiffies so this
simplifies things removing the need for calculation all over the place.
The change necessitated a type change in the tpm_chip struct to hold
jiffies.
Signed-off-by: Kylie Hall <kjhall@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The driver for the next generation of TPM chips version 1.2 including support
for interrupts. The Trusted Computing Group has written the TPM Interface
Specification (TIS) which defines a common interface for all manufacturer's
1.2 TPM's thus the name tpm_tis.
Signed-off-by: Leendert van Doorn <leendert@watson.ibm.com>
Signed-off-by: Kylene Hall <kjhall@us.ibm.com>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Many of the sysfs files were calling the TPM_GetCapability command with array.
Since for 1.2 more sysfs files of this type are coming I am generalizing the
array so there can be one array and the unique parts can be filled in just
before the command is called.
This updated version of the patch breaks the multi-value sysfs file into
separate files pointed out by Greg. It also addresses the code redundancy and
ugliness in the tpm_show_* functions pointed out on another patch by Dave
Hansen.
Signed-off-by: Kylene Hall <kjhall@us.ibm.com>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
With the TPM 1.2 Specification, each command is classified as short, medium or
long and the chip tells you the maximum amount of time for a response to each
class of command. This patch provides and array of the classifications and a
function to determine how long the response should be waited for. Also, it
uses that information in the command processing to determine how long to poll
for. The function is exported so the 1.2 driver can use the functionality to
determine how long to wait for a DataAvailable interrupt if interrupts are
being used.
Signed-off-by: Kylene Hall <kjhall@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Changes in the 1.2 TPM Specification make it necessary to update some fields
of the chip structure in the initialization function after it is registered
with tpm.c thus tpm_register_hardware was modified to return a pointer to the
structure. This patch makes that change and the associated changes in
tpm_atmel and tpm_nsc. The changes to tpm_infineon will be coming in a patch
from Marcel Selhorst.
Signed-off-by: Kylene Hall <kjhall@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
To assist with chip management and better support the possibility of having
multiple TPMs in the system of the same kind, the struct tpm_vendor_specific
member of the tpm_chip was changed from a pointer to an instance. This patch
changes that declaration and fixes up all accesses to the structure member
except in tpm_infineon which is coming in a patch from Marcel Selhorst.
Signed-off-by: Kylene Hall <kjhall@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Many of the sysfs files were calling the TPM_GetCapability command with array.
Since for 1.2 more sysfs files of this type are coming I am generalizing the
array so there can be one array and the unique parts can be filled in just
before the command is called.
Signed-off-by: Kylene Hall <kjhall@us.ibm.com>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The following patch set contains numerous changes to the base tpm driver
(tpm.c) to support the next generation of TPM chips. The changes include new
sysfs files because of more relevant data being available, a function to
access the timeout and duration values for the chip, and changes to make use
of those duration values. Duration in the TPM specification is defined as the
maximum amount of time the chip could take to return the results. Commands
are in one of three categories short, medium and long. Also included are
cleanups of how the commands for the sysfs files are composed to reduce a
bunch of redundant arrays.
This patch:
Fix minor spacing issues.
Signed-off-by: Kylene Hall <kjhall@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
A string corresponding to the tcpa_pc_event_id POST_CONTENTS was missing
causing an overflow bug when access was attempted in the get_event_name
function.
This bug was found by Coverity.
Signed-off-by: Kylene Hall <kjhall@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The eventname was kmalloc'd and not freed in the *_show functions.
This bug was found by Coverity.
Signed-off-by: Kylene Hall <kjhall@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
from: Greg Howard <ghoward@sgi.com>
Fix Altix system controller (snsc) device names to include the slot number
of the blade whose associated system controller is the target of the device
interface. Including the slot number avoids a problem we're currently
having where slots within the same enclosure are attempting to create
multiple kobjects with identical names.
Signed-off-by: Greg Howard <ghoward@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix a possible Oops in the Siemens Gigaset base driver when the device is
unplugged while an ISDN connection is still active, and makes sure that the
isdn4linux link level (LL) is properly informed if a connection is broken
by the USB cable being unplugged.
- Avoid unsafe checks of URB status fields outside the URB completion
handlers, keep track of in-use URBs myself instead.
- If an isochronous transfer URB completes with status==0, also check the
status of the frame descriptors.
- Verify length of interrupt messages received from the device.
- Align the length limit on transmitted AT commands with the device
documentation.
- In case of AT response receive overrun, keep newly arrived instead of old
unread data.
- Remove redundant check of device ID in the USB probe function.
- Correct and improve some comments and formatting.
Signed-off-by: Tilman Schmidt <tilman@imap.cc>
Acked-by: Hansjoerg Lipp <hjlipp@web.de>
Cc: Karsten Keil <kkeil@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Using the old ioctl interface together with cardbus card gives a NULL
pointer dereference since cardbus devices don't have a struct pcmcia_device.
also s->io[0].res can be NULL as well.
Fix is to move the pcmcia code after the cardbus code and to check for a null
pointer.
Signed-off-by: Daniel Ritz <daniel.ritz@gmx.ch>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
This patch updates "depends on" for PCMCIA_VRC4171.
CONFIG_VRC4171 has been removed, so replace it with CPU_VR41XX && ISA.
Signed-off-by: Yoichi Yuasa <yoichi_yuasa@tripeaks.co.jp>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
As static maps do not have IO resources, this setting oopses. However, as
we do not ever read this value, we can safely remove it.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
If we set dev_node to NULL too early, some drivers which used this to
determine whether unregister_netdev() needs to be called fail when removing
a PCMCIA card.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
The comment of "pcmcia_load_firmware" is wrong: the
firmware(*.cis) files reside in /lib/firmware/ _not_
/lib/firmware/cis/ .
Signed-off-by: komurojun-mbn@nifty.com
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Use list_add instead of list_add_tail for pcmcia_device_add
so that second device of multi-function-card will be unloaded first.
Signed-off-by: komurojun-mbn@nifty.com
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
This means "DMA Read returns" can bypass "MMIO Writes".
Violating the PCI specs in this case improves outbound DMA "flows"
and is currently not required by any drivers.
This is NOT a new behavior. Previous chipsets did this
already and I believe ZX1 PDC was already setting this
for hpux. I just want to further document the behavior.
Signed-off-by: Grant Grundler <grundler@parisc-linux.org>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
SERIAL_SGI_IOC4 and BLK_DEV_SGIIOC4 depend upon SGI_IOC4, and
SERIAL_SGI_IOC3 depends upon SGI_IOC3. Currently the definitions
are out of order in the config sequence.
Fix by including drivers/sn/Kconfig immediately after SGI_SN,
upon which SGI_IOC4 and SGI_IOC3 depend.
Signed-off-by: Brent Casavant <bcasavan@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
This fixes an oops in 2.6.16.X when loading the snd_powermac module. The
name of the requested module changed during the 2.6.16 development cycle
from i2c-keylargo to i2c-powermac.
Signed-off-by: Guido Guenther <agx@sigxcpu.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch fixes several bugs in the gianfar driver, including a major one
where spinlocks were horribly broken:
* Split gianfar locks into two types: TX and RX
* Made it so gfar_start() now clears RHALT
* Fixed a bug where calling gfar_start_xmit() with interrupts off would
corrupt the interrupt state
* Fixed a bug where a frame could potentially arrive, and never be handled
(if no more frames arrived
* Fixed a bug where the rx_work_limit would never be observed by the rx
completion code
* Fixed a bug where the interrupt handlers were not actually protected by
their spinlocks
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Correct the base address of the Realtek RTL8019AS chip on the Toshiba RBTX4938
board -- this should make the driver work at least when CONFIG_PCI is enabled.
Signed-off-by: Yuri Shpilevsky <yshpilevsky@ru.mvista.com>
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
- fix mddev_lock() usage bugs in md_attr_show() and md_attr_store().
[they did not anticipate the possibility of getting a signal]
- remove mddev_lock_uninterruptible() [unused]
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Acked-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
