The following speed modes are now supported in J7200 SoC,
- HS200 and HS400 modes at 1.8 V card voltage, in MMCSD0 subsystem [1].
- UHS-I speed modes in MMCSD1 subsystem [1].
Add support for UHS-I modes by adding voltage regulator device tree nodes
and corresponding pinmux details, to power cycle and voltage switch cards.
Set respective tags in sdhci0 and remove no-1-8-v tag from sdhci1
device tree nodes.
Also update the delay values for various speed modes supported, based on
the revised january 2021 J7200 datasheet[2].
[1] - section 12.3.6.1.1 MMCSD Features, in
https://www.ti.com/lit/ug/spruiu1a/spruiu1a.pdf,
(SPRUIU1A – JULY 2020 – REVISED JANUARY 2021)
[2] - https://www.ti.com/lit/ds/symlink/dra821u.pdf,
(SPRSP57B – APRIL 2020 – REVISED JANUARY 2021)
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Kishon Vijay Abraham I <kishon@ti.com>
Link: https://lore.kernel.org/r/20210326064120.31919-4-a-govindraju@ti.com
There are 6 gpio instances inside SoC with 2 groups as show below:
Group one: wkup_gpio0, wkup_gpio1
Group two: main_gpio0, main_gpio2, main_gpio4, main_gpio6
Only one instance from each group can be used at a time. So use main_gpio0
and wkup_gpio0 in current linux context and disable the rest of the nodes.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Link: https://lore.kernel.org/r/20210326064120.31919-3-a-govindraju@ti.com
x2 lane PCIe slot in the common processor board is enabled and connected to
j7200 SOM. Add PCIe DT node in common processor board to reflect the
same.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>
Link: https://lore.kernel.org/r/20210105151421.23237-7-kishon@ti.com
Add sub-nodes to SERDES0 DT node to represent SERDES0 is connected
to PCIe and QSGMII (multi-link SERDES).
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>
Link: https://lore.kernel.org/r/20210105151421.23237-6-kishon@ti.com
J7200 main_i2c1 is connected to the i2c bus on the CPB marked as main_i2c3
The i2c1 devices on the CPB are _not_ connected to the SoC, they are not
usable with the J7200 SOM.
Correct the expander name from exp4 to exp3 and at the same time add the
line names as well.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Link: https://lore.kernel.org/r/20201120073533.24486-3-peter.ujfalusi@ti.com
The J7200 SOM have additional io expander which is used to control several
SOM level muxes to make sure that the correct signals are routed to the
correct pin on the SOM <-> CPB connectors.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Link: https://lore.kernel.org/r/20201120073533.24486-2-peter.ujfalusi@ti.com
Follow the device tree standards that states to set the
status="reserved" if an device is operational, but used by a non-linux
firmware in the system.
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Tony Lindgren <tony@atomide.com>
Acked-by: Vignesh Raghavendra <vigneshr@ti.com>
Link: https://lore.kernel.org/r/20201113211826.13087-6-nm@ti.com
J7200 has a single instance of 8 channel ADC in MCU domain. Add DT node
for the same.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Sekhar Nori <nsekhar@ti.com>
Link: https://lore.kernel.org/r/20201029050950.4500-1-vigneshr@ti.com
The board uses lane 3 of SERDES for USB. Set the mux
accordingly.
The USB controller and EVM supports super-speed for USB0
on the Type-C port. However, the SERDES has a limitation
that upto 2 protocols can be used at a time. The SERDES is
wired for PCIe, QSGMII and USB super-speed. It has been
chosen to use PCI2 and QSGMII as default. So restrict
USB0 to high-speed mode.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>
Link: https://lore.kernel.org/r/20200930122032.23481-7-rogerq@ti.com
First two lanes of SERDES is connected to PCIe, third lane is
connected to QSGMII and the last lane is connected to USB. However,
Cadence torrent SERDES doesn't support more than 2 protocols
at the same time. Configure it only for PCIe and QSGMII.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>
Link: https://lore.kernel.org/r/20200930122032.23481-6-rogerq@ti.com
Add support for the eMMC and SD card connected on the common
processor board
sdhci0 is connected to an eMMC while sdhci1 is connected to the
micro SD slot.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Tested-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Sekhar Nori <nsekhar@ti.com>
Link: https://lore.kernel.org/r/20200924112644.11076-3-faiz_abbas@ti.com
Add DT nodes for I2C GPIO expanders on main_i2c0 and main_i2c1 and
also add the pinmux corresponding to these I2C instances.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Sekhar Nori <nsekhar@ti.com>
Reviewed-by: Faiz Abbas <faiz_abbas@ti.com>
Link: https://lore.kernel.org/r/20200923155400.13757-3-vigneshr@ti.com
The TI J7200 EVM base board has TI DP83867 PHY connected to external CPSW
NUSS Port 1 in rgmii-rxid mode.
Hence, add pinmux and Ethernet PHY configuration for TI J7200 SoC MCU
Gigabit Ethernet two ports Switch subsystem (CPSW NUSS).
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Suman Anna <s-anna@ti.com>
Link: https://lore.kernel.org/r/20200923220938.30788-5-grygorii.strashko@ti.com
Add support for J7200 Common Processor Board.
The EVM architecture is very similar to J721E as follows:
+------------------------------------------------------+
| +-------------------------------------------+ |
| | | |
| | Add-on Card 1 Options | |
| | | |
| +-------------------------------------------+ |
| |
| |
| +-------------------+ |
| | | |
| | SOM | |
| +--------------+ | | |
| | | | | |
| | Add-on | +-------------------+ |
| | Card 2 | | Power Supply
| | Options | | |
| | | | |
| +--------------+ | <---
+------------------------------------------------------+
Common Processor Board
Common Processor board is the baseboard that has most of the actual
connectors, power supply etc. A SOM (System on Module) is plugged on
to the common processor board and this contains the SoC, PMIC, DDR and
basic high speed components necessary for functionality.
Note:
* The minimum configuration required to boot up the board is System On
Module(SOM) + Common Processor Board.
* Since there is just a single SOM and Common Processor Board, we are
maintaining common processor board as the base dts and SOM as the dtsi
that we include. In the future as more SOM's appear, we should move
common processor board as a dtsi and include configurations as dts.
* All daughter cards beyond the basic boards shall be maintained as
overlays.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Suman Anna <s-anna@ti.com>
Link: https://lore.kernel.org/r/20200914162231.2535-6-lokeshvutla@ti.com
