Add support for PHY_INTERFACE_MODE_5GBASER mode within the Marvell CP110
common PHY driver.
This is currently only supported via SMC calls to TF-A. Legacy support
may be added later, if needed.
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The original changes brakes MAC address assignment on older chip
versions (see bug report [0]), and it brakes random MAC assignment.
is_valid_ether_addr() requires that its argument is word-aligned.
Add the missing alignment to array mac_addr.
[0] https://bugzilla.kernel.org/show_bug.cgi?id=215087
Fixes: 1c5d09d587 ("ethernet: r8169: use eth_hw_addr_set()")
Reported-by: Richard Herbert <rherbert@sympatico.ca>
Tested-by: Richard Herbert <rherbert@sympatico.ca>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Acked-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2021-11-22
Maciej Fijalkowski says:
Here are the two fixes for issues around ethtool's set_channels()
callback for ice driver. Both are related to XDP resources. First one
corrects the size of vsi->txq_map that is used to track the usage of Tx
resources and the second one prevents the wrong refcounting of bpf_prog.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Alex Elder says:
====================
net: ipa: prevent shutdown during setup
The setup phase of the IPA driver occurs in one of two ways.
Normally, it is done directly by the main driver probe function.
But some systems (those having a "modem-init" DTS property) don't
start setup until an SMP2P interrupt (sent by the modem) arrives.
Because it isn't performed by the probe function, setup on
"modem-init" systems could be underway at the time a driver
remove (or shutdown) request arrives (or vice-versa). This
situation can lead to hardware state not being cleaned up
properly.
This series addresses this problem by having the driver remove
function disable the setup interrupt. A consequence of this is
that setup will complete if it is underway when the remove function
is called.
So now, when removing the driver, setup:
- will have already completed;
- is underway, and will complete before proceeding; or
- will not have begun (and will not occur).
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The IPA setup_complete flag is set at the end of ipa_setup(), when
the setup phase of initialization has completed successfully. This
occurs as part of driver probe processing, or (if "modem-init" is
specified in the DTS file) it is triggered by the "ipa-setup-ready"
SMP2P interrupt generated by the modem.
In the latter case, it's possible for driver shutdown (or remove) to
begin while setup processing is underway, and this can't be allowed.
The problem is that the setup_complete flag is not adequate to signal
that setup is underway.
If setup_complete is set, it will never be un-set, so that case is
not a problem. But if setup_complete is false, there's a chance
setup is underway.
Because setup is triggered by an interrupt on a "modem-init" system,
there is a simple way to ensure the value of setup_complete is safe
to read. The threaded handler--if it is executing--will complete as
part of a request to disable the "ipa-modem-ready" interrupt. This
means that ipa_setup() (which is called from the handler) will run
to completion if it was underway, or will never be called otherwise.
The request to disable the "ipa-setup-ready" interrupt is currently
made within ipa_modem_stop(). Instead, disable the interrupt
outside that function in the two places it's called. In the case of
ipa_remove(), this ensures the setup_complete flag is safe to read
before we read it.
Rename ipa_smp2p_disable() to be ipa_smp2p_irq_disable_setup(), to be
more specific about its effect.
Fixes: 530f9216a9 ("soc: qcom: ipa: AP/modem communications")
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
We currently maintain a "disabled" Boolean flag to determine whether
the "ipa-setup-ready" SMP2P IRQ handler does anything. That flag
must be accessed under protection of a mutex.
Instead, disable the SMP2P interrupt when requested, which prevents
the interrupt handler from ever being called. More importantly, it
synchronizes a thread disabling the interrupt with the completion of
the interrupt handler in case they run concurrently.
Use the IPA setup_complete flag rather than the disabled flag in the
handler to determine whether to ignore any interrupts arriving after
the first.
Rename the "disabled" flag to be "setup_disabled", to be specific
about its purpose.
Fixes: 530f9216a9 ("soc: qcom: ipa: AP/modem communications")
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sr is a repeated start, it is used in both I2C and SMBus protocols.
Provide its description and replace start ("S") conditions with repeated
start ("Sr") conditions when relevant. This allows the documentation to
match the SMBus specification available at [1].
[1] http://www.smbus.org/specs/SMBus_3_1_20180319.pdf
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Ansuel Smith says:
====================
Add mirror and LAG support to qca8k
With the continue of adding 'Multiple feature to qca8k'
The switch supports mirror mode and LAG.
In mirror mode a port is set as mirror and other port are configured
to both igress or egress mode. With no port configured for mirror,
the mirror port is disabled and reverted to normal port.
The switch supports max 4 LAG with 4 different member max.
Current supported mode is Hash mode in both L2 or L2+3 mode.
There is a problematic implementation for the hash mode where
with multiple LAG configured, someone has to remove them to
change the hash mode as it's global.
When a member of the LAG is disconnected, the traffic is redirected
to the other port.
Some warning are present from checkpatch but can't really be fixed
as it would result in making the regs less readable.
(They really did their best with the LAG reg logic and complexity)
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Add LAG support to this switch. In Documentation this is described as
trunk mode. A max of 4 LAGs are supported and each can support up to 4
port. The current tx mode supported is Hash mode with both L2 and L2+3
mode.
When no port are present in the trunk, the trunk is disabled in the
switch.
When a port is disconnected, the traffic is redirected to the other
available port.
The hash mode is global and each LAG require to have the same hash mode
set. To change the hash mode when multiple LAG are configured, it's
required to remove each LAG and set the desired hash mode to the last.
An error is printed when it's asked to set a not supported hadh mode.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The switch supports mirror mode. Only one port can set as mirror port and
every other port can set to both ingress and egress mode. The mirror
port is disabled and reverted to normal operation once every port is
removed from sending packet to it.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add neigh_confirm() for the confirmed member in struct neighbour,
it can be called as an independent unit by other functions.
Signed-off-by: Yajun Deng <yajun.deng@linux.dev>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change adds a MCTP Serial transport binding, as defined by DMTF
specificiation DSP0253 - "MCTP Serial Transport Binding". This is
implemented as a new serial line discipline, and can be attached to
arbitrary tty devices.
From the Kconfig description:
This driver provides an MCTP-over-serial interface, through a
serial line-discipline, as defined by DMTF specification "DSP0253 -
MCTP Serial Transport Binding". By attaching the ldisc to a serial
device, we get a new net device to transport MCTP packets.
This allows communication with external MCTP endpoints which use
serial as their transport. It can also be used as an easy way to
provide MCTP connectivity between virtual machines, by forwarding
data between simple virtual serial devices.
Say y here if you need to connect to MCTP endpoints over serial. To
compile as a module, use m; the module will be called mctp-serial.
Once the N_MCTP line discipline is set [using ioctl(TCIOSETD)], we get a
new netdev suitable for MCTP communication.
The 'mctp' utility[1] provides a simple wrapper for this ioctl, using
'link serial <device>':
# mctp link serial /dev/ttyS0 &
# mctp link
dev lo index 1 address 0x00:00:00:00:00:00 net 1 mtu 65536 up
dev mctpserial0 index 5 address 0x(no-addr) net 1 mtu 68 down
[1]: https://github.com/CodeConstruct/mctp
Signed-off-by: Jeremy Kerr <jk@codeconstruct.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Schimmel says:
====================
mlxsw: Two small fixes
Patch #1 fixes a recent regression that prevents the driver from loading
with old firmware versions.
Patch #2 protects the driver from a NULL pointer dereference when
working on top of a buggy firmware. This was never observed in an actual
system, only on top of an emulator during development.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
When processing port up/down events generated by the device's firmware,
the driver protects itself from events reported for non-existent local
ports, but not the CPU port (local port 0), which exists, but lacks a
netdev.
This can result in a NULL pointer dereference when calling
netif_carrier_{on,off}().
Fix this by bailing early when processing an event reported for the CPU
port. Problem was only observed when running on top of a buggy emulator.
Fixes: 28b1987ef5 ("mlxsw: spectrum: Register CPU port with devlink")
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver fails to load with old firmware versions that cannot report
the maximum number of RIF MAC profiles [1].
Fix this by defaulting to a maximum of a single profile in such
situations, as multiple profiles are not supported by old firmware
versions.
[1]
mlxsw_spectrum 0000:03:00.0: cannot register bus device
mlxsw_spectrum: probe of 0000:03:00.0 failed with error -5
Fixes: 1c375ffb2e ("mlxsw: spectrum_router: Expose RIF MAC profiles to devlink resource")
Signed-off-by: Danielle Ratson <danieller@nvidia.com>
Reported-by: Vadim Pasternak <vadimp@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Schimmel says:
====================
mlxsw: Various updates
Patch #1 removes deadcode reported by Coverity.
Patch #2 adds a shutdown method in the PCI driver to ensure the kexeced
kernel starts working with a device that is in a sane state.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
On an arm64 platform with the Spectrum ASIC, after loading and executing
a new kernel via kexec, the following trace [1] is observed. This seems
to be caused by the fact that the device is not properly shutdown before
executing the new kernel.
Fix this by implementing a shutdown method which mirrors the remove
method, as recommended by the kexec maintainer [2][3].
[1]
BUG: Bad page state in process devlink pfn:22f73d
page:fffffe00089dcf40 refcount:-1 mapcount:0 mapping:0000000000000000 index:0x0
flags: 0x2ffff00000000000()
raw: 2ffff00000000000 0000000000000000 ffffffff089d0201 0000000000000000
raw: 0000000000000000 0000000000000000 ffffffffffffffff 0000000000000000
page dumped because: nonzero _refcount
Modules linked in:
CPU: 1 PID: 16346 Comm: devlink Tainted: G B 5.8.0-rc6-custom-273020-gac6b365b1bf5 #44
Hardware name: Marvell Armada 7040 TX4810M (DT)
Call trace:
dump_backtrace+0x0/0x1d0
show_stack+0x1c/0x28
dump_stack+0xbc/0x118
bad_page+0xcc/0xf8
check_free_page_bad+0x80/0x88
__free_pages_ok+0x3f8/0x418
__free_pages+0x38/0x60
kmem_freepages+0x200/0x2a8
slab_destroy+0x28/0x68
slabs_destroy+0x60/0x90
___cache_free+0x1b4/0x358
kfree+0xc0/0x1d0
skb_free_head+0x2c/0x38
skb_release_data+0x110/0x1a0
skb_release_all+0x2c/0x38
consume_skb+0x38/0x130
__dev_kfree_skb_any+0x44/0x50
mlxsw_pci_rdq_fini+0x8c/0xb0
mlxsw_pci_queue_fini.isra.0+0x28/0x58
mlxsw_pci_queue_group_fini+0x58/0x88
mlxsw_pci_aqs_fini+0x2c/0x60
mlxsw_pci_fini+0x34/0x50
mlxsw_core_bus_device_unregister+0x104/0x1d0
mlxsw_devlink_core_bus_device_reload_down+0x2c/0x48
devlink_reload+0x44/0x158
devlink_nl_cmd_reload+0x270/0x290
genl_rcv_msg+0x188/0x2f0
netlink_rcv_skb+0x5c/0x118
genl_rcv+0x3c/0x50
netlink_unicast+0x1bc/0x278
netlink_sendmsg+0x194/0x390
__sys_sendto+0xe0/0x158
__arm64_sys_sendto+0x2c/0x38
el0_svc_common.constprop.0+0x70/0x168
do_el0_svc+0x28/0x88
el0_sync_handler+0x88/0x190
el0_sync+0x140/0x180
[2]
https://www.mail-archive.com/linux-kernel@vger.kernel.org/msg1195432.html
[3]
https://patchwork.kernel.org/project/linux-scsi/patch/20170212214920.28866-1-anton@ozlabs.org/#20116693
Cc: Eric Biederman <ebiederm@xmission.com>
Signed-off-by: Danielle Ratson <danieller@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The function idr_for_each_entry() already checks that the next entry in
the IDR is not NULL.
Therefore, checking that again in every iteration leads to deadcode.
Remove the unnecessary check in order to avoid that.
Addresses-Coverity: ("Logically dead code")
Signed-off-by: Danielle Ratson <danieller@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tony Lu says:
====================
smc: Fixes for closing process and minor cleanup
Patch 1 is a minor cleanup for local struct sock variables.
Patch 2 ensures the active closing side enters TIME_WAIT.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The side that actively closed socket, it's clcsock doesn't enter
TIME_WAIT state, but the passive side does it. It should show the same
behavior as TCP sockets.
Consider this, when client actively closes the socket, the clcsock in
server enters TIME_WAIT state, which means the address is occupied and
won't be reused before TIME_WAIT dismissing. If we restarted server, the
service would be unavailable for a long time.
To solve this issue, shutdown the clcsock in [A], perform the TCP active
close progress first, before the passive closed side closing it. So that
the actively closed side enters TIME_WAIT, not the passive one.
Client | Server
close() // client actively close |
smc_release() |
smc_close_active() // PEERCLOSEWAIT1 |
smc_close_final() // abort or closed = 1|
smc_cdc_get_slot_and_msg_send() |
[A] |
|smc_cdc_msg_recv_action() // ACTIVE
| queue_work(smc_close_wq, &conn->close_work)
| smc_close_passive_work() // PROCESSABORT or APPCLOSEWAIT1
| smc_close_passive_abort_received() // only in abort
|
|close() // server recv zero, close
| smc_release() // PROCESSABORT or APPCLOSEWAIT1
| smc_close_active()
| smc_close_abort() or smc_close_final() // CLOSED
| smc_cdc_get_slot_and_msg_send() // abort or closed = 1
smc_cdc_msg_recv_action() | smc_clcsock_release()
queue_work(smc_close_wq, &conn->close_work) | sock_release(tcp) // actively close clc, enter TIME_WAIT
smc_close_passive_work() // PEERCLOSEWAIT1 | smc_conn_free()
smc_close_passive_abort_received() // CLOSED|
smc_conn_free() |
smc_clcsock_release() |
sock_release(tcp) // passive close clc |
Link: https://www.spinics.net/lists/netdev/msg780407.html
Fixes: b38d732477 ("smc: socket closing and linkgroup cleanup")
Signed-off-by: Tony Lu <tonylu@linux.alibaba.com>
Reviewed-by: Wen Gu <guwen@linux.alibaba.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There remains some variables to replace with local struct sock. So clean
them up all.
Fixes: 3163c5071f ("net/smc: use local struct sock variables consistently")
Signed-off-by: Tony Lu <tonylu@linux.alibaba.com>
Reviewed-by: Wen Gu <guwen@linux.alibaba.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
MIPS/IA64 define END as assembly function ending, which conflict
with END definition in slip.h, just undef it at first
Reported-by: lkp@intel.com
Signed-off-by: Huang Pei <huangpei@loongson.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
MIPS/IA64 define END as assembly function ending, which conflict
with END definition in mkiss.c, just undef it at first
Reported-by: lkp@intel.com
Signed-off-by: Huang Pei <huangpei@loongson.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 5fa6863ba6 ("spi: Check we have a spi_device_id for each DT
compatible") added a test to check that every SPI driver has a
spi_device_id for each DT compatiable string defined by the driver
and warns if the spi_device_id is missing. The spi_device_id is
missing for the MMC SPI driver and the following warning is now seen.
WARNING KERN SPI driver mmc_spi has no spi_device_id for mmc-spi-slot
Fix this by adding the necessary spi_device_id.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Link: https://lore.kernel.org/r/20211115113813.238044-1-jonathanh@nvidia.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
If a timeout is hit, it can result is incorrect data on the I2C bus
and/or memory corruptions in the guest since the device can still be
operating on the buffers it was given while the guest has freed them.
Here is, for example, the start of a slub_debug splat which was
triggered on the next transfer after one transfer was forced to timeout
by setting a breakpoint in the backend (rust-vmm/vhost-device):
BUG kmalloc-1k (Not tainted): Poison overwritten
First byte 0x1 instead of 0x6b
Allocated in virtio_i2c_xfer+0x65/0x35c age=350 cpu=0 pid=29
__kmalloc+0xc2/0x1c9
virtio_i2c_xfer+0x65/0x35c
__i2c_transfer+0x429/0x57d
i2c_transfer+0x115/0x134
i2cdev_ioctl_rdwr+0x16a/0x1de
i2cdev_ioctl+0x247/0x2ed
vfs_ioctl+0x21/0x30
sys_ioctl+0xb18/0xb41
Freed in virtio_i2c_xfer+0x32e/0x35c age=244 cpu=0 pid=29
kfree+0x1bd/0x1cc
virtio_i2c_xfer+0x32e/0x35c
__i2c_transfer+0x429/0x57d
i2c_transfer+0x115/0x134
i2cdev_ioctl_rdwr+0x16a/0x1de
i2cdev_ioctl+0x247/0x2ed
vfs_ioctl+0x21/0x30
sys_ioctl+0xb18/0xb41
There is no simple fix for this (the driver would have to always create
bounce buffers and hold on to them until the device eventually returns
the buffers), so just disable the timeout support for now.
Fixes: 3cfc883804 ("i2c: virtio: add a virtio i2c frontend driver")
Acked-by: Jie Deng <jie.deng@intel.com>
Signed-off-by: Vincent Whitchurch <vincent.whitchurch@axis.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Currently interrupt storm will occur from i2c-i801 after first
transaction if SMB_ALERT signal is enabled and ever asserted. It is
enough if the signal is asserted once even before the driver is loaded
and does not recover because that interrupt is not acknowledged.
This fix aims to fix it by two ways:
- Add acknowledging for the SMB_ALERT interrupt status
- Disable the SMB_ALERT interrupt on platforms where possible since the
driver currently does not make use for it
Acknowledging resets the SMB_ALERT interrupt status on all platforms and
also should help to avoid interrupt storm on older platforms where the
SMB_ALERT interrupt disabling is not available.
For simplicity this fix reuses the host notify feature for disabling and
restoring original register value.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=177311
Reported-by: ck+kernelbugzilla@bl4ckb0x.de
Reported-by: stephane.poignant@protonmail.com
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Tested-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
If driver interrupts are enabled, SMBHSTCNT_INTREN will be 1 after
the first transaction, and will stay to that value forever. This
means that interrupts will be generated for both host-initiated
transactions and also SMBus Alert events even after the driver is
unloaded. To be on the safe side, we should restore the initial state
of this bit at suspend and reboot time, as we do for several other
configuration bits already and for the same reason: the BIOS should
be handed the device in the same configuration state in which we
received it. Otherwise interrupts may be generated which nobody
will process.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Tested-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
The i.MX 8QM DTS files use two compatibles, so update the binding to fix
dtbs_check warnings like:
arch/arm64/boot/dts/freescale/imx8qm-mek.dt.yaml: i2c@5a800000:
compatible: ['fsl,imx8qm-lpi2c', 'fsl,imx7ulp-lpi2c'] is too long
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
disk->fops->owner is grabbed in blkdev_get_no_open() after the disk
kobject refcount is increased. This way can't make sure that
disk->fops->owner is still alive since del_gendisk() still can move
on if the kobject refcount of disk is grabbed by open() and
disk->fops->open() isn't called yet.
Fixes the issue by moving try_module_get() into blkdev_get_by_dev()
with ->open_mutex() held, then we can drain the in-progress open()
in del_gendisk(). Meantime new open() won't succeed because disk
becomes not alive.
This way is reasonable because blkdev_get_no_open() needn't to touch
disk->fops or defined callbacks.
Cc: Christoph Hellwig <hch@lst.de>
Cc: czhong@redhat.com
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/20211111020343.316126-1-ming.lei@redhat.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
We must flush the TLB before releasing i_mmap_rwsem to avoid the
potential reuse of an unshared PMDs page. This is not true in the case
of move_hugetlb_page_tables(). The last reference on the page table can
therefore be dropped before the TLB flush took place.
Prevent it by reordering the operations and flushing the TLB before
releasing i_mmap_rwsem.
Fixes: 550a7d60bd ("mm, hugepages: add mremap() support for hugepage backed vma")
Signed-off-by: Nadav Amit <namit@vmware.com>
Reviewed-by: Mike Kravetz <mike.kravetz@oracle.com>
Cc: Mina Almasry <almasrymina@google.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When __unmap_hugepage_range() calls to huge_pmd_unshare() succeed, a TLB
flush is missing. This TLB flush must be performed before releasing the
i_mmap_rwsem, in order to prevent an unshared PMDs page from being
released and reused before the TLB flush took place.
Arguably, a comprehensive solution would use mmu_gather interface to
batch the TLB flushes and the PMDs page release, however it is not an
easy solution: (1) try_to_unmap_one() and try_to_migrate_one() also call
huge_pmd_unshare() and they cannot use the mmu_gather interface; and (2)
deferring the release of the page reference for the PMDs page until
after i_mmap_rwsem is dropeed can confuse huge_pmd_unshare() into
thinking PMDs are shared when they are not.
Fix __unmap_hugepage_range() by adding the missing TLB flush, and
forcing a flush when unshare is successful.
Fixes: 24669e5847 ("hugetlb: use mmu_gather instead of a temporary linked list for accumulating pages)" # 3.6
Signed-off-by: Nadav Amit <namit@vmware.com>
Reviewed-by: Mike Kravetz <mike.kravetz@oracle.com>
Cc: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Set the RDMA protocol to use at driver bind time based on the ice PF's
rdma_mode flag.
Signed-off-by: Shiraz Saleem <shiraz.saleem@intel.com>
Tested-by: Leszek Kaliszczuk <leszek.kaliszczuk@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Allow support for 'enable_iwarp' and 'enable_roce' devlink params to turn
on/off iWARP or RoCE protocol support for E800 devices.
For example, a user can turn on iWARP functionality with,
devlink dev param set pci/0000:07:00.0 name enable_iwarp value true cmode runtime
This add an iWARP auxiliary rdma device, ice.iwarp.<>, under this PF.
A user request to enable both iWARP and RoCE under the same PF is rejected
since this device does not support both protocols simultaneously on the
same port.
Signed-off-by: Shiraz Saleem <shiraz.saleem@intel.com>
Tested-by: Leszek Kaliszczuk <leszek.kaliszczuk@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Add a new device generic parameter to enable and disable
iWARP functionality on a multi-protocol RDMA device.
Signed-off-by: Shiraz Saleem <shiraz.saleem@intel.com>
Tested-by: Leszek Kaliszczuk <leszek.kaliszczuk@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Nikolay Aleksandrov says:
====================
net: nexthop: fix refcount issues when replacing groups
This set fixes a refcount bug when replacing nexthop groups and
modifying routes. It is complex because the objects look valid when
debugging memory dumps, but we end up having refcount dependency between
unlinked objects which can never be released, so in turn they cannot
free their resources and refcounts. The problem happens because we can
have stale IPv6 per-cpu dsts in nexthops which were removed from a
group. Even though the IPv6 gen is bumped, the dsts won't be released
until traffic passes through them or the nexthop is freed, that can take
arbitrarily long time, and even worse we can create a scenario[1] where it
can never be released. The fix is to release the IPv6 per-cpu dsts of
replaced nexthops after an RCU grace period so no new ones can be
created. To do that we add a new IPv6 stub - fib6_nh_release_dsts, which
is used by the nexthop code only when necessary. We can further optimize
group replacement, but that is more suited for net-next as these patches
would have to be backported to stable releases.
v2: patch 02: update commit msg
patch 03: check for mausezahn before testing and make a few comments
more verbose
[1]
This info is also present in patch 02's commit message.
Initial state:
$ ip nexthop list
id 200 via 2002:db8::2 dev bridge.10 scope link onlink
id 201 via 2002:db8::3 dev bridge scope link onlink
id 203 group 201/200
$ ip -6 route
2001:db8::10 nhid 203 metric 1024 pref medium
nexthop via 2002:db8::3 dev bridge weight 1 onlink
nexthop via 2002:db8::2 dev bridge.10 weight 1 onlink
Create rt6_info through one of the multipath legs, e.g.:
$ taskset -a -c 1 ./pkt_inj 24 bridge.10 2001:db8::10
(pkt_inj is just a custom packet generator, nothing special)
Then remove that leg from the group by replace (let's assume it is id
200 in this case):
$ ip nexthop replace id 203 group 201
Now remove the IPv6 route:
$ ip -6 route del 2001:db8::10/128
The route won't be really deleted due to the stale rt6_info holding 1
refcnt in nexthop id 200.
At this point we have the following reference count dependency:
(deleted) IPv6 route holds 1 reference over nhid 203
nh 203 holds 1 ref over id 201
nh 200 holds 1 ref over the net device and the route due to the stale
rt6_info
Now to create circular dependency between nh 200 and the IPv6 route, and
also to get a reference over nh 200, restore nhid 200 in the group:
$ ip nexthop replace id 203 group 201/200
And now we have a permanent circular dependncy because nhid 203 holds a
reference over nh 200 and 201, but the route holds a ref over nh 203 and
is deleted.
To trigger the bug just delete the group (nhid 203):
$ ip nexthop del id 203
It won't really be deleted due to the IPv6 route dependency, and now we
have 2 unlinked and deleted objects that reference each other: the group
and the IPv6 route. Since the group drops the reference it holds over its
entries at free time (i.e. its own refcount needs to drop to 0) that will
never happen and we get a permanent ref on them, since one of the entries
holds a reference over the IPv6 route it will also never be released.
At this point the dependencies are:
(deleted, only unlinked) IPv6 route holds reference over group nh 203
(deleted, only unlinked) group nh 203 holds reference over nh 201 and 200
nh 200 holds 1 ref over the net device and the route due to the stale
rt6_info
This is the last point where it can be fixed by running traffic through
nh 200, and specifically through the same CPU so the rt6_info (dst) will
get released due to the IPv6 genid, that in turn will free the IPv6
route, which in turn will free the ref count over the group nh 203.
If nh 200 is deleted at this point, it will never be released due to the
ref from the unlinked group 203, it will only be unlinked:
$ ip nexthop del id 200
$ ip nexthop
$
Now we can never release that stale rt6_info, we have IPv6 route with ref
over group nh 203, group nh 203 with ref over nh 200 and 201, nh 200 with
rt6_info (dst) with ref over the net device and the IPv6 route. All of
these objects are only unlinked, and cannot be released, thus they can't
release their ref counts.
Message from syslogd@dev at Nov 19 14:04:10 ...
kernel:[73501.828730] unregister_netdevice: waiting for bridge.10 to become free. Usage count = 3
Message from syslogd@dev at Nov 19 14:04:20 ...
kernel:[73512.068811] unregister_netdevice: waiting for bridge.10 to become free. Usage count = 3
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The new selftest runs a sequence which causes circular refcount
dependency between deleted objects which cannot be released and results
in a netdevice refcount imbalance.
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When replacing a nexthop group, we must release the IPv6 per-cpu dsts of
the removed nexthop entries after an RCU grace period because they
contain references to the nexthop's net device and to the fib6 info.
With specific series of events[1] we can reach net device refcount
imbalance which is unrecoverable. IPv4 is not affected because dsts
don't take a refcount on the route.
[1]
$ ip nexthop list
id 200 via 2002:db8::2 dev bridge.10 scope link onlink
id 201 via 2002:db8::3 dev bridge scope link onlink
id 203 group 201/200
$ ip -6 route
2001:db8::10 nhid 203 metric 1024 pref medium
nexthop via 2002:db8::3 dev bridge weight 1 onlink
nexthop via 2002:db8::2 dev bridge.10 weight 1 onlink
Create rt6_info through one of the multipath legs, e.g.:
$ taskset -a -c 1 ./pkt_inj 24 bridge.10 2001:db8::10
(pkt_inj is just a custom packet generator, nothing special)
Then remove that leg from the group by replace (let's assume it is id
200 in this case):
$ ip nexthop replace id 203 group 201
Now remove the IPv6 route:
$ ip -6 route del 2001:db8::10/128
The route won't be really deleted due to the stale rt6_info holding 1
refcnt in nexthop id 200.
At this point we have the following reference count dependency:
(deleted) IPv6 route holds 1 reference over nhid 203
nh 203 holds 1 ref over id 201
nh 200 holds 1 ref over the net device and the route due to the stale
rt6_info
Now to create circular dependency between nh 200 and the IPv6 route, and
also to get a reference over nh 200, restore nhid 200 in the group:
$ ip nexthop replace id 203 group 201/200
And now we have a permanent circular dependncy because nhid 203 holds a
reference over nh 200 and 201, but the route holds a ref over nh 203 and
is deleted.
To trigger the bug just delete the group (nhid 203):
$ ip nexthop del id 203
It won't really be deleted due to the IPv6 route dependency, and now we
have 2 unlinked and deleted objects that reference each other: the group
and the IPv6 route. Since the group drops the reference it holds over its
entries at free time (i.e. its own refcount needs to drop to 0) that will
never happen and we get a permanent ref on them, since one of the entries
holds a reference over the IPv6 route it will also never be released.
At this point the dependencies are:
(deleted, only unlinked) IPv6 route holds reference over group nh 203
(deleted, only unlinked) group nh 203 holds reference over nh 201 and 200
nh 200 holds 1 ref over the net device and the route due to the stale
rt6_info
This is the last point where it can be fixed by running traffic through
nh 200, and specifically through the same CPU so the rt6_info (dst) will
get released due to the IPv6 genid, that in turn will free the IPv6
route, which in turn will free the ref count over the group nh 203.
If nh 200 is deleted at this point, it will never be released due to the
ref from the unlinked group 203, it will only be unlinked:
$ ip nexthop del id 200
$ ip nexthop
$
Now we can never release that stale rt6_info, we have IPv6 route with ref
over group nh 203, group nh 203 with ref over nh 200 and 201, nh 200 with
rt6_info (dst) with ref over the net device and the IPv6 route. All of
these objects are only unlinked, and cannot be released, thus they can't
release their ref counts.
Message from syslogd@dev at Nov 19 14:04:10 ...
kernel:[73501.828730] unregister_netdevice: waiting for bridge.10 to become free. Usage count = 3
Message from syslogd@dev at Nov 19 14:04:20 ...
kernel:[73512.068811] unregister_netdevice: waiting for bridge.10 to become free. Usage count = 3
Fixes: 7bf4796dd0 ("nexthops: add support for replace")
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We need a way to release a fib6_nh's per-cpu dsts when replacing
nexthops otherwise we can end up with stale per-cpu dsts which hold net
device references, so add a new IPv6 stub called fib6_nh_release_dsts.
It must be used after an RCU grace period, so no new dsts can be created
through a group's nexthop entry.
Similar to fib6_nh_release it shouldn't be used if fib6_nh_init has failed
so it doesn't need a dummy stub when IPv6 is not enabled.
Fixes: 7bf4796dd0 ("nexthops: add support for replace")
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ansuel Smith says:
====================
Multiple cleanup and feature for qca8k
This is a reduced version of the old massive series.
Refer to the changelog to know what is removed from this.
We clean and convert the driver to GENMASK FIELD_PREP to clean multiple
use of various naming scheme. (example we have a mix of _MASK, _S _M,
and various name) The idea is to ""simplify"" and remove some shift and
data handling by using FIELD API.
The patch contains various checkpatch warning and are ignored to not
create more mess in the header file. (fixing the too long line warning
would results in regs definition less readable)
We conver the driver to regmap API as ipq40xx SoC is based on the same
reg structure and we need to generilize the read/write access to split
the driver to commond and specific code.
The conversion to regmap is NOT done for the read/write/rmw operation,
the function are reworked to use the regmap helper instead.
This is done to keep the patch delta low but will come sooner or later
when the code will be split.
Any new feature will directly use the regmap helper and the reg
set/clear and the busy wait function are migrated to regmap helper as
the use of these function is low.
We also add a minor patch for MIB counter as qca8337 is missing 2 extra
counter, support for mdb and ageing settings.
v3:
- Try to reduce regmap conversion patch
v2:
- Move regmap init to sw_probe instead of moving switch id check.
- Removed LAGs, mirror extra features will come later in another
smaller series.
- Squash 2 ageing patch
- Add more description about the regmap patch
- Rework mdb patch to do operation under the same lock
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for mdb add/del function. The ARL table is used to insert
the rule. The rule will be searched, deleted and reinserted with the
port mask updated. The function will check if the rule has to be updated
or insert directly with no deletion of the old rule.
If every port is removed from the port mask, the rule is removed.
The rule is set STATIC in the ARL table (aka it doesn't age) to not be
flushed by fast age function.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
qca8k support setting ageing time in step of 7s. Add support for it and
set the max value accepted of 7645m.
Documentation talks about support for 10000m but that values doesn't
make sense as the value doesn't match the max value in the reg.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The switch supports fast aging by flushing any rule in the ARL
table for a specific port.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
