When stmmac_mdio_reset, was called from stmmac_resume, it was not
resetting the PHY due to which MAC was not getting reset properly and
hence ethernet interface not was resumed properly.
The issue was currently only reproducible on stih301-b2204.
Signed-off-by: Pankaj Dev <pankaj.dev@st.com>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The reset delays used for stmmac are in the order of 10ms to 1 second,
which is far too long for udelay usage, so switch to using msleep.
Practically this fixes the PHY not being reliably detected in some cases
as udelay wouldn't actually delay for long enough to let the phy
reliably be reset.
Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the much more common pr_warn instead of pr_warning.
Other miscellanea:
o Typo fixes submiting/submitting
o Coalesce formats
o Realign arguments
o Add missing terminating '\n' to formats
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds simple cleanups for stmmac, removing test we know is always
true, fixing whitespace, and moving code out of if().
Signed-off-by: Pavel Machek <pavel@denx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
mii_irq[] array is never initialized anywhere in the driver, thus mii_irq[]
will always equate to zero. So, for the case where the PHY does not have an
irq, we should use PHY_POLL for that situation.
Signed-off-by: Dinh Nguyen <dinguyen@altera.com>
Tested-by: Vince Bridgers <vbridger@altera.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch promotes stmmac_mdio_reset function from static to
non-static, so that power management functions can decide to reset if
the IP comes out from lowe power state specially hibernation cases.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes gpio_free for reset line of the phy, driver stores
the gpio number in its private data-structure to use in future. As the
driver uses this pin in future this pin should not be freed.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds phy reset callback support for stmmac driver via device
trees. It adds three new properties to gmac device tree bindings to
define the reset signal via gpio.
With this patch users can conveniently pass reset gpio number with pre,
pulse and post delay in micro secs via DTs.
active low:
_________ ____________
<pre-delay> |<pulse-delay> |<post-delay>
| |
|_______________|
active high:
________________
<pre-delay> |<pulse-delay> |<post-delay>
| |
________| |___________
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch tidies up the code. I have run Linden (and verified with checkpatch)
many part of the driver trying to reorganize some sections respecting the
codying-style rules in the points where it was not done.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With this patch the stmmac fails in case of the phy device
is not found; w/o this fix the mdio can be register twice when
do down/up the iface and this is not correct.
Reported-by: Stas <stsp@list.ru>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes bus_id from mdio platform data, The reason to remove
bus_id is, stmmac mdio bus_id is always same as stmmac bus-id, so there
is no point in passing this in different variable.
Also stmmac ethernet driver connects to phy with bus_id passed its
platform data.
So, having single bus-id is much simpler.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a basic check in stmmac_mdio_unregister to see if mdio
bus registeration for this driver was actually sucessfull or not.
Use case here is, if BSP considers using mdio-gpio bus along with stmmac
driver by passing mdio_bus_data as NULL in platform data.
Call to stmmac_mdio_register with mdio_bus_data as NULL returns 0, which
is a considered sucessfull call form stmmac. Then again when we unload
the driver we just call stmmac_mdio_unregister, this is were the actual
problem is stmmac-mdio code dont really know at this instance of calling
that stmmac_mdio_register was actually successful.
So Adding a check in stmmac_mdio_unregister is always safe.
Without this patch stmmac driver calls stmmac_mdio_register from
stmmac_release which Segfaults as mii bus was never registered at the
first point.
Originally the this bug was found when unloading an stmmac driver
instance which uses mdio-gpio for smi access.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If a specific clk_csr value is passed from the platform
this means that the CSR Clock Range selection cannot be
changed at run-time and it is fixed (as reported in the driver
documentation). Viceversa the driver will try to set the MDC
clock dynamically according to the actual clock input.
Signed-off-by: Deepak Sikri <deepak.sikri@st.com>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Reviewed-by: Francesco Virlinzi <francesco.virlinzi@st.com>
Reviewed-by: David Laight <david.laight@aculab.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The CSR Clock Range has been reworked and new macros has
been added in the platform header to allow the CSR Clock
Range selection in the GMII Address Register.
The previous work didn't add the other fields
that can be used to achieve MDC clock of frequency
higher than the IEEE 802.3 specified frequency limit
of 2.5 MHz and program a clock divider of lower value.
On such platforms, these are used indeed so this patch
adds them.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes the infinite waits from the mdio read and
write interfaces. These infinite waits have been replaced by
the timeout handling. In case if a time out occurs, an error is
returned.
Signed-off-by: Deepak Sikri <deepak.sikri@st.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After commit "db8857b stmmac: use an unique MDIO bus name" my
device stopped being probed because two different names were being
used in different places. This fixes the inconsistency.
Signed-off-by: Alessandro Rubini <rubini@gnudd.com>
Acked-by: Giancarlo Asnaghi <giancarlo.asnaghi@st.com>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Florian Fainelli <florian@openwrt.org>
Acked-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the PCI support (as EXPERIMENTAL)
this has been also tested on XLINX XC2V3000 FF1152AMT0221
D1215994A VIRTEX FPGA board.
To support the PCI bus the main part has been reworked
and both the platform and the PCI specific parts have
been moved into different files.
Signed-off-by: Rayagond Kokatanur <rayagond@vayavyalabs.com>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the STMicroelectronics driver into driver/net/ethernet/stmicro/ and
make the necessary Kconfig and Makefile changes.
CC: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
