Until not so long ago, there were system log messages pointing to
inconsistent MTRR setup of the video frame buffer caused by the way vesafb
and X worked. While vesafb was fixed meanwhile, I believe fixing it there
only hides a shortcoming in the MTRR code itself, in that that code is not
symmetric with respect to the ordering of attempts to set up two (or more)
regions where one contains the other. In the current shape, it permits
only setting up sub-regions of pre-exisiting ones. The patch below makes
this symmetric.
While working on that I noticed a few more inconsistencies in that code,
namely
- use of 'unsigned int' for sizes in many, but not all places (the patch
is converting this to use 'unsigned long' everywhere, which specifically
might be necessary for x86-64 once a processor supporting more than 44
physical address bits would become available)
- the code to correct inconsistent settings during secondary processor
startup tried (if necessary) to correct, among other things, the value
in IA32_MTRR_DEF_TYPE, however the newly computed value would never get
used (i.e. stored in the respective MSR)
- the generic range validation code checked that the end of the
to-be-added range would be above 1MB; the value checked should have been
the start of the range
- when contained regions are detected, previously this was allowed only
when the old region was uncacheable; this can be symmetric (i.e. the new
region can also be uncacheable) and even further as per Intel's
documentation write-trough and write-back for either region is also
compatible with the respective opposite in the other
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Just like on x86-64, don't touch foreign CPUs' memory if the watchdog
isn't enabled at all.
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Signed-off-by: Andi Kleen <ak@suse.de>
While not strictly required with the current code (as the upper half of
page table entries generated by __set_fixmap() cannot be non-zero due
to the second parameter of this function being 'unsigned long'), the
use of set_pte() in __set_fixmap() in the context of clear_fixmap() is
still improper with CONFIG_X86_PAE (see the respective comment in
include/asm-i386/pgtable-3level.h) and would turn into a bug if that
second parameter ever gets changed to a 64-bit type.
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Signed-off-by: Andi Kleen <ak@suse.de>
gcc doesn't support -mtune=core2 yet, but will be soon. Use -mtune=generic or -mtune=i686
as fallback
TBD need benchmarking for INTEL_USERCOPY etc. So far I used the same defaults as MPENTIUMM
Signed-off-by: Andi Kleen <ak@suse.de>
Add a way to disable the timer IRQ routing check via a boot option. The
VMI timer code uses this to avoid triggering the pester Mingo code, which
probes for some very unusual and broken motherboard routings. It fires
100% of the time when using a paravirtual delay mechanism instead of using
a realtime delay, since there is no elapsed real time, and the 4 timer IRQs
have not yet been delivered.
In addition, it is entirely possible, though improbable, that this bug
could surface on real hardware which picks a particularly bad time to enter
SMM mode, causing a long latency during one of the timer IRQs.
While here, make check_timer be __init.
Signed-off-by: Zachary Amsden <zach@vmware.com>
Signed-off-by: Andi Kleen <ak@suse.de>
[chrisw: use no_timer_check to bring inline with x86_64 as per Andi's request]
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
BIOS ROM areas may not be mapped into the guest address space, so be careful
when touching those addresses to make sure they appear to be mapped.
[akpm@osdl.org: fix unused var warning]
AK: Changed __get_user to probe_kernel_address
Signed-off-by: Jeremy Fitzhardinge <jeremy@xensource.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Andi Kleen <ak@suse.de>
Cc: Jeremy Fitzhardinge <jeremy@goop.org>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Add the three bare TLB accessor functions to paravirt-ops. Most amusingly,
flush_tlb is redefined on SMP, so I can't call the paravirt op flush_tlb.
Instead, I chose to indicate the actual flush type, kernel (global) vs. user
(non-global). Global in this sense means using the global bit in the page
table entry, which makes TLB entries persistent across CR3 reloads, not
global as in the SMP sense of invoking remote shootdowns, so the term is
confusingly overloaded.
AK: folded in fix from Zach for PAE compilation
Signed-off-by: Zachary Amsden <zach@vmware.com>
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
Signed-off-by: Andi Kleen <ak@suse.de>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Jeremy Fitzhardinge <jeremy@goop.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Add APIC accessors to paravirt-ops. Unfortunately, we need two write
functions, as some older broken hardware requires workarounds for
Pentium APIC errata - this is the purpose of apic_write_atomic.
AK: replaced __inline with inline
Signed-off-by: Zachary Amsden <zach@vmware.com>
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
Signed-off-by: Andi Kleen <ak@suse.de>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Jeremy Fitzhardinge <jeremy@goop.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Two legacy power management modes are much easier to just explicitly disable
when running in paravirtualized mode - neither APM nor PnP is still relevant.
The status of ACPI is still debatable, and noacpi is still a common enough
boot parameter that it is not necessary to explicitly disable ACPI.
Signed-off-by: Zachary Amsden <zach@vmware.com>
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
Signed-off-by: Andi Kleen <ak@suse.de>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Jeremy Fitzhardinge <jeremy@goop.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Allow selected bug checks to be skipped by paravirt kernels. The two most
important are the F00F workaround (which is either done by the hypervisor,
or not required), and the 'hlt' instruction check, which can break under
some hypervisors.
Signed-off-by: Zachary Amsden <zach@vmware.com>
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
Signed-off-by: Andi Kleen <ak@suse.de>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Jeremy Fitzhardinge <jeremy@goop.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
1) Each hypervisor writes a probe function to detect whether we are
running under that hypervisor. paravirt_probe() registers this
function.
2) If vmlinux is booted with ring != 0, we call all the probe
functions (with registers except %esp intact) in link order: the
winner will not return.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
Signed-off-by: Andi Kleen <ak@suse.de>
Cc: Jeremy Fitzhardinge <jeremy@goop.org>
Cc: Zachary Amsden <zach@vmware.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Both lhype and Xen want to call the core of the x86 cpu detect code before
calling start_kernel.
(extracted from larger patch)
AK: folded in start_kernel header patch
Signed-off-by: Jeremy Fitzhardinge <jeremy@xensource.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Andi Kleen <ak@suse.de>
Cc: Jeremy Fitzhardinge <jeremy@goop.org>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
It turns out that the most called ops, by several orders of magnitude,
are the interrupt manipulation ops. These are obvious candidates for
patching, so mark them up and create infrastructure for it.
The method used is that the ops structure has a patch function, which
is called for each place which needs to be patched: this returns a
number of instructions (the rest are NOP-padded).
Usually we can spare a register (%eax) for the binary patched code to
use, but in a couple of critical places in entry.S we can't: we make
the clobbers explicit at the call site, and manually clobber the
allowed registers in debug mode as an extra check.
And:
Don't abuse CONFIG_DEBUG_KERNEL, add CONFIG_DEBUG_PARAVIRT.
And:
AK: Fix warnings in x86-64 alternative.c build
And:
AK: Fix compilation with defconfig
And:
^From: Andrew Morton <akpm@osdl.org>
Some binutlises still like to emit references to __stop_parainstructions and
__start_parainstructions.
And:
AK: Fix warnings about unused variables when PARAVIRT is disabled.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Jeremy Fitzhardinge <jeremy@xensource.com>
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
Signed-off-by: Zachary Amsden <zach@vmware.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Create a paravirt.h header for all the critical operations which need to be
replaced with hypervisor calls, and include that instead of defining native
operations, when CONFIG_PARAVIRT.
This patch does the dumbest possible replacement of paravirtualized
instructions: calls through a "paravirt_ops" structure. Currently these are
function implementations of native hardware: hypervisors will override the ops
structure with their own variants.
All the pv-ops functions are declared "fastcall" so that a specific
register-based ABI is used, to make inlining assember easier.
And:
+From: Andy Whitcroft <apw@shadowen.org>
The paravirt ops introduce a 'weak' attribute onto memory_setup().
Code ordering leads to the following warnings on x86:
arch/i386/kernel/setup.c:651: warning: weak declaration of
`memory_setup' after first use results in unspecified behavior
Move memory_setup() to avoid this.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
Signed-off-by: Andi Kleen <ak@suse.de>
Cc: Jeremy Fitzhardinge <jeremy@goop.org>
Cc: Zachary Amsden <zach@vmware.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Andy Whitcroft <apw@shadowen.org>
IOPL is implicitly saved and restored on task switch,
so explicit check is no longer needed.
Signed-off-by: Chuck Ebbert <76306.1226@compuserve.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Makes the intention of the code cleaner to read and avoids
a potential deadlock on mmap_sem. Also change the types of
the arguments to not include __user because they're really
not user addresses.
Signed-off-by: Andi Kleen <ak@suse.de>
The entry.S code at work_notifysig is surely wrong. It drops into unrelated
code if the branch to work_notifysig_v86 is taken, and CONFIG_VM86=n.
[PATCH] Make vm86 support optional
tree 9b5daef528
pushed to git Jan 8, 2006, and first appears in 2.6.16
The 'fix' here is to also compile out the vm86 test & branch when
CONFIG_VM86=n.
Signed-off-by: Joe Korty <joe.korty@ccur.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Extend bzImage protocol to enable bootloaders to load a completely relocatable
bzImage. Now protected mode component of kernel is also relocatable and a
boot-loader can load the protected mode component at a differnt physical
address than 1MB. (If kernel was built with CONFIG_RELOCATABLE)
Kexec can make use of it to load this kernel at a different physical address
to capture kernel crash dumps.
Signed-off-by: Vivek Goyal <vgoyal@in.ibm.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
o Now CONFIG_PHYSICAL_START is being replaced with CONFIG_PHYSICAL_ALIGN.
Hardcoding the kernel physical start value creates a problem in relocatable
kernel context due to boot loader limitations. For ex, if somebody
compiles a relocatable kernel to be run from address 4MB, but this kernel
will run from location 1MB as grub loads the kernel at physical address
1MB. Kernel thinks that I am a relocatable kernel and I should run from
the address I have been loaded at. So somebody wanting to run kernel
from 4MB alignment location (for improved performance regions) can't do
that.
o Hence, Eric proposed that probably CONFIG_PHYSICAL_ALIGN will make
more sense in relocatable kernel context. At run time kernel will move
itself to a physical addr location which meets user specified alignment
restrictions.
Signed-off-by: Vivek Goyal <vgoyal@in.ibm.com>
Signed-off-by: Andi Kleen <ak@suse.de>
o Relocations generated w.r.t absolute symbols are not processed as by
definition, absolute symbols are not to be relocated. Explicitly warn
user about absolutions relocations present at compile time.
o These relocations get introduced either due to linker optimizations or
some programming oversights.
o Also create a list of symbols which have been audited to be safe and
don't emit warnings for these.
Signed-off-by: Vivek Goyal <vgoyal@in.ibm.com>
Signed-off-by: Andi Kleen <ak@suse.de>
This patch modifies the i386 kernel so that if CONFIG_RELOCATABLE is
selected it will be able to be loaded at any 4K aligned address below
1G. The technique used is to compile the decompressor with -fPIC and
modify it so the decompressor is fully relocatable. For the main
kernel relocations are generated. Resulting in a kernel that is relocatable
with no runtime overhead and no need to modify the source code.
A reserved 32bit word in the parameters has been assigned
to serve as a stack so we figure out where are running.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Vivek Goyal <vgoyal@in.ibm.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Defining __PHYSICAL_START and __KERNEL_START in asm-i386/page.h works but
it triggers a full kernel rebuild for the silliest of reasons. This
modifies the users to directly use CONFIG_PHYSICAL_START and linux/config.h
which prevents the full rebuild problem, which makes the code much
more maintainer and hopefully user friendly.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Vivek Goyal <vgoyal@in.ibm.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Currently when we are reserving the memory the kernel text
resides in we start at __PHYSICAL_START which happens to be
correct but not very obvious. In addition when we start relocating
the kernel __PHYSICAL_START is the wrong value, as it is an
absolute symbol that does not get relocated.
By starting the reservation at __pa_symbol(_text)
the code is clearer and will be correct when relocated.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Vivek Goyal <vgoyal@in.ibm.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Ld knows about 2 kinds of symbols, absolute and section
relative. Section relative symbols symbols change value
when a section is moved and absolute symbols do not.
Currently in the linker script we have several labels
marking the beginning and ending of sections that
are outside of sections, making them absolute symbols.
Having a mixture of absolute and section relative
symbols refereing to the same data is currently harmless
but it is confusing.
This must be done carefully as newer revs of ld do not place
symbols that appear in sections without data and instead
ld makes those symbols global :(
My ultimate goal is to build a relocatable kernel. The
safest and least intrusive technique is to generate
relocation entries so the kernel can be relocated at load
time. The only penalty would be an increase in the size
of the kernel binary. The problem is that if absolute and
relocatable symbols are not properly specified absolute symbols
will be relocated or section relative symbols won't be, which
is fatal.
The practical motivation is that when generating kernels that
will run from a reserved area for analyzing what caused
a kernel panic, it is simpler if you don't need to hard code
the physical memory location they will run at, especially
for the distributions.
[AK: and merged:]
o Also put a message so that in future people can be aware of it and
avoid introducing absolute symbols.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Vivek Goyal <vgoyal@in.ibm.com>
Signed-off-by: Andi Kleen <ak@suse.de>
On modern systems RAM errors don't cause NMIs, but it's usually
caused by PCI SERR. Mention PCI instead of RAM in the printk.
Reported by r_hayashi@ctc-g.co.jp (Ryutaro Hayashi)
Cc: r_hayashi@ctc-g.co.jp
Signed-off-by: Andi Kleen <ak@suse.de>
Resending as I believe the discussion about them established they were
correct.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Currently the idle loop has two nested loops -- one high level
in cpu_idle and in some low level idle functions another one.
Looping in the low level idle functions breaks the idle notifiers
because interrupts waking up sleep states need to execute
exit_idle() which is only in cpu_idle().
So don't do that, only loop in cpu_idle(). This only removes
code.
In some cases e.g. poll_idle the idle loop is a little longer
now because cpu_idle checks more things. I hope that isn't a problem
ACPI idle doesn't change behaviour because it never looped anyways.
Cc: len.brown@intel.com
Cc: eranian@hpl.hp.com
Signed-off-by: Andi Kleen <ak@suse.de>
Use the pcurrent field in the PDA to implement the "current" macro. This ends
up compiling down to a single instruction to get the current task.
Signed-off-by: Jeremy Fitzhardinge <jeremy@xensource.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Cc: Chuck Ebbert <76306.1226@compuserve.com>
Cc: Zachary Amsden <zach@vmware.com>
Cc: Jan Beulich <jbeulich@novell.com>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Use the cpu_number in the PDA to implement raw_smp_processor_id. This is a
little simpler than using thread_info, though the cpu field in thread_info
cannot be removed since it is used for things other than getting the current
CPU in common code.
Signed-off-by: Jeremy Fitzhardinge <jeremy@xensource.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Cc: Chuck Ebbert <76306.1226@compuserve.com>
Cc: Zachary Amsden <zach@vmware.com>
Cc: Jan Beulich <jbeulich@novell.com>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
sys_vm86 uses a struct kernel_vm86_regs, which is identical to pt_regs, but
adds an extra space for all the segment registers. Previously this structure
was completely independent, so changes in pt_regs had to be reflected in
kernel_vm86_regs. This changes just embeds pt_regs in kernel_vm86_regs, and
makes the appropriate changes to vm86.c to deal with the new naming.
Also, since %gs is dealt with differently in the kernel, this change adjusts
vm86.c to reflect this.
While making these changes, I also cleaned up some frankly bizarre code which
was added when auditing was added to sys_vm86.
Signed-off-by: Jeremy Fitzhardinge <jeremy@xensource.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Cc: Chuck Ebbert <76306.1226@compuserve.com>
Cc: Zachary Amsden <zach@vmware.com>
Cc: Jan Beulich <jbeulich@novell.com>
Cc: Andi Kleen <ak@suse.de>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Jason Baron <jbaron@redhat.com>
Cc: Chris Wright <chrisw@sous-sol.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
There are a few places where the change in struct pt_regs and the use of %gs
affect the userspace ABI. These are primarily debugging interfaces where
thread state can be inspected or extracted.
Signed-off-by: Jeremy Fitzhardinge <jeremy@xensource.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Cc: Chuck Ebbert <76306.1226@compuserve.com>
Cc: Zachary Amsden <zach@vmware.com>
Cc: Jan Beulich <jbeulich@novell.com>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
This patch is the meat of the PDA change. This patch makes several related
changes:
1: Most significantly, %gs is now used in the kernel. This means that on
entry, the old value of %gs is saved away, and it is reloaded with
__KERNEL_PDA.
2: entry.S constructs the stack in the shape of struct pt_regs, and this
is passed around the kernel so that the process's saved register
state can be accessed.
Unfortunately struct pt_regs doesn't currently have space for %gs
(or %fs). This patch extends pt_regs to add space for gs (no space
is allocated for %fs, since it won't be used, and it would just
complicate the code in entry.S to work around the space).
3: Because %gs is now saved on the stack like %ds, %es and the integer
registers, there are a number of places where it no longer needs to
be handled specially; namely context switch, and saving/restoring the
register state in a signal context.
4: And since kernel threads run in kernel space and call normal kernel
code, they need to be created with their %gs == __KERNEL_PDA.
Signed-off-by: Jeremy Fitzhardinge <jeremy@xensource.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Cc: Chuck Ebbert <76306.1226@compuserve.com>
Cc: Zachary Amsden <zach@vmware.com>
Cc: Jan Beulich <jbeulich@novell.com>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
When a CPU is brought up, a PDA and GDT are allocated for it. The GDT's
__KERNEL_PDA entry is pointed to the allocated PDA memory, so that all
references using this segment descriptor will refer to the PDA.
This patch rearranges CPU initialization a bit, so that the GDT/PDA are set up
as early as possible in cpu_init(). Also for secondary CPUs, GDT+PDA are
preallocated and initialized so all the secondary CPU needs to do is set up
the ldt and load %gs. This will be important once smp_processor_id() and
current use the PDA.
In all cases, the PDA is set up in head.S, before a CPU starts running C code,
so the PDA is always available.
Signed-off-by: Jeremy Fitzhardinge <jeremy@xensource.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Cc: Chuck Ebbert <76306.1226@compuserve.com>
Cc: Zachary Amsden <zach@vmware.com>
Cc: Jan Beulich <jbeulich@novell.com>
Cc: Andi Kleen <ak@suse.de>
Cc: James Bottomley <James.Bottomley@SteelEye.com>
Cc: Matt Tolentino <matthew.e.tolentino@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
This patch has the basic definitions of struct i386_pda, and the segment
selector in the GDT.
asm-i386/pda.h is more or less a direct copy of asm-x86_64/pda.h. The most
interesting difference is the use of _proxy_pda, which is used to give gcc a
model for the actual memory operations on the real pda structure. No actual
reference is ever made to _proxy_pda, so it is never defined.
Signed-off-by: Jeremy Fitzhardinge <jeremy@xensource.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Cc: Chuck Ebbert <76306.1226@compuserve.com>
Cc: Zachary Amsden <zach@vmware.com>
Cc: Jan Beulich <jbeulich@novell.com>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Use asm-offsets for the offsets of registers into the pt_regs struct, rather
than having hard-coded constants
I left the constants in the comments of entry.S because they're useful for
reference; the code in entry.S is very dependent on the layout of pt_regs,
even when using asm-offsets.
Signed-off-by: Jeremy Fitzhardinge <jeremy@xensource.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Cc: Keith Owens <kaos@ocs.com.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
ioremap must be balanced by an iounmap and failing to do so can result
in a memory leak.
Tested (compilation only):
- using allmodconfig
- making sure the files are compiling without any warning/error due to
new changes
Signed-off-by: Amol Lad <amol@verismonetworks.com>
Signed-off-by: Andi Kleen <ak@suse.de>
i386 port of the sLeAZY-fpu feature. Chuck reports that this gives him a +/-
0.4% improvement on his simple benchmark
x86_64 description follows:
Right now the kernel on x86-64 has a 100% lazy fpu behavior: after *every*
context switch a trap is taken for the first FPU use to restore the FPU
context lazily. This is of course great for applications that have very
sporadic or no FPU use (since then you avoid doing the expensive save/restore
all the time). However for very frequent FPU users... you take an extra trap
every context switch.
The patch below adds a simple heuristic to this code: After 5 consecutive
context switches of FPU use, the lazy behavior is disabled and the context
gets restored every context switch. If the app indeed uses the FPU, the trap
is avoided. (the chance of the 6th time slice using FPU after the previous 5
having done so are quite high obviously).
After 256 switches, this is reset and lazy behavior is returned (until there
are 5 consecutive ones again). The reason for this is to give apps that do
longer bursts of FPU use still the lazy behavior back after some time.
Signed-off-by: Chuck Ebbert <76306.1226@compuserve.com>
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Andi Kleen <ak@suse.de>
Clean up the espfix code:
- Introduced PER_CPU() macro to be used from asm
- Introduced GET_DESC_BASE() macro to be used from asm
- Rewrote the fixup code in asm, as calling a C code with the altered %ss
appeared to be unsafe
- No longer altering the stack from a .fixup section
- 16bit per-cpu stack is no longer used, instead the stack segment base
is patched the way so that the high word of the kernel and user %esp
are the same.
- Added the limit-patching for the espfix segment. (Chuck Ebbert)
[jeremy@goop.org: use the x86 scaling addressing mode rather than shifting]
Signed-off-by: Stas Sergeev <stsp@aknet.ru>
Signed-off-by: Andi Kleen <ak@suse.de>
Acked-by: Zachary Amsden <zach@vmware.com>
Acked-by: Chuck Ebbert <76306.1226@compuserve.com>
Acked-by: Jan Beulich <jbeulich@novell.com>
Cc: Andi Kleen <ak@muc.de>
Signed-off-by: Jeremy Fitzhardinge <jeremy@goop.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
When a spinlock lockup occurs, arrange for the NMI code to emit an all-cpu
backtrace, so we get to see which CPU is holding the lock, and where.
Cc: Andi Kleen <ak@muc.de>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Badari Pulavarty <pbadari@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Andi Kleen <ak@suse.de>
This patch removes the default_ldt[] array, as it has been unused since
iBCS stopped being supported. This means it is now possible to actually
set an empty LDT segment.
In order to deal with this, the set_ldt_desc/load_LDT pair has been
replaced with a single set_ldt() operation which is responsible for both
setting up the LDT descriptor in the GDT, and reloading the LDT register.
If there are no LDT entries, the LDT register is loaded with a NULL
descriptor.
Signed-off-by: Jeremy Fitzhardinge <jeremy@xensource.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Cc: Andi Kleen <ak@suse.de>
Acked-by: Zachary Amsden <zach@vmware.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Here is a patch (used by perfmon2) to detect the presence of the Precise Event
Based Sampling (PEBS) feature for i386. The patch also adds the cpu_has_pebs
macro.
- adds X86_FEATURE_PEBS
- adds cpu_has_pebs to test for X86_FEATURE_PEBS
Signed-off-by: stephane eranian <eranian@hpl.hp.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
This just got removed on x86-64, do the same on 32bit.
It always annoyed me when this ate a line of oops output pushing
interesting stuff off the screen.
Signed-off-by: Dave Jones <davej@redhat.com>
Signed-off-by: Andi Kleen <ak@suse.de>
The unwinder has some extra newlines, which eat up loads of screen
space when it spews. (See https://bugzilla.redhat.com/bugzilla/attachment.cgi?id=137900
for a nasty example).
warning_symbol-> and warning-> already printk a newline, so don't add one
in the strings passed to them.
[AK: redone for new code]
Signed-off-by: Dave Jones <davej@redhat.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Fix checks that failed to realize that values are 4-kB-unit-sized (note the
format strings in this same diff context which *do* realize the unit size,
via appended "000"!). Also fix an incorrect below-1MB area check (as
gathered from Jan Beulich's unapplied patch at
http://www.ussg.iu.edu/hypermail/linux/kernel/0411.1/1378.html ) Update
mtrr_add_page() docu to make 4-kB-sized calculation more obvious.
Given several further items mentioned in Jan's patch mail, all in all MTRR
code seems surprisingly buggy, for a surprisingly long period of time (many
years). Further work/investigation would be useful.
TBD Note that my patch is pretty much UNTESTED, since I can only verify that it
TBD successfully boots my machine, but I cannot test against actual buggy
TBD hardware which would require these (formerly broken) checks. Long -mm
TBD simmering would make sense, especially since these now-working checks might
TBD turn out to have adverse effects on unaffected hardware.
Signed-off-by: Andreas Mohr <andi@lisas.de>
Signed-off-by: Andi Kleen <ak@suse.de>
Acked-by: Jan Beulich <jbeulich@novell.com>
Cc: Andi Kleen <ak@muc.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Conflicts:
drivers/ata/libata-scsi.c
include/linux/libata.h
Futher merge of Linus's head and compilation fixups.
Signed-Off-By: David Howells <dhowells@redhat.com>
Conflicts:
drivers/infiniband/core/iwcm.c
drivers/net/chelsio/cxgb2.c
drivers/net/wireless/bcm43xx/bcm43xx_main.c
drivers/net/wireless/prism54/islpci_eth.c
drivers/usb/core/hub.h
drivers/usb/input/hid-core.c
net/core/netpoll.c
Fix up merge failures with Linus's head and fix new compilation failures.
Signed-Off-By: David Howells <dhowells@redhat.com>
This reverts commit 281ea49b0c,
which broke ACPI Interrupt source overrides that move
the SCI from one IRQ in PIC mode to another in IOAPIC mode.
If the SCI shared an interrupt line with another device,
this would result in a "irq 18: nobody cared" type failure.
http://bugzilla.kernel.org/show_bug.cgi?id=7601
Signed-off-by: Len Brown <len.brown@intel.com>
Converts from using struct "class_device" to "struct device" making
everything show up properly in /sys/devices/ with symlinks from the
/sys/class directory.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Converts from using struct "class_device" to "struct device" making
everything show up properly in /sys/devices/ with symlinks from the
/sys/class directory.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch makes the needlessly global pci_bf_sort static.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Acked-by: Matt Domsch <Matt_Domsch@dell.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This updated patch adds the Intel ICH9 LPC and SMBus Controller DID's.
Signed-off-by: Jason Gaston <jason.d.gaston@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
ioremap must be balanced by an iounmap and failing to do so can result
in a memory leak.
Tested (compilation only):
- using allmodconfig
- making sure the files are compiling without any warning/error due to
new changes
Signed-off-by: Amol Lad <amol@verismonetworks.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Mostly CodingStyle cleanups for arch/i386/pci/i386.c:
- fit in 80 columns;
- use a #defined value instead of an inline constant;
Also change one resource_size_t (DBG) printk from %08lx to %lx since
it can be more than 32 bits (more than 8 hexits).
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The number of permutations of crap we do is amazing and almost all of it
has the wrong effect in 2.6.
At the heart of this is the PCI SFF magic which says that compatibility
mode PCI IDE controllers use ISA IRQ routing and hard coded addresses
not the BAR values. The old quirks variously clears them, sets them,
adjusts them and then IDE ignores the result.
In order to drive all this garbage out and to do it portably we need to
handle the SFF rules directly and properly. Because we know the device
BAR 0-3 are not used in compatibility mode we load them with the values
that are implied (and indeed which many controllers actually
thoughtfully put there in this mode anyway).
This removes special cases in the IDE layer and libata which now knows
that bar 0/1/2/3 always contain the correct address. It means our
resource allocation map is accurate from boot, not "mostly accurate"
after ide is loaded, and it shoots lots of code. There is also lots more
code and magic constant knowledge to shoot once this is in and settled.
Been in my test tree for a while both with drivers/ide and with libata.
Wants some -mm shakedown in case I've missed something dumb or there are
corner cases lurking.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When showing the stack backtrace, make sure that we never accept not
only an unchanging frame pointer, but also a frame pointer that moves
back down the stack frame. It must always grow up (toward older stack
frames).
I doubt this has triggered, but a subtly corrupt stack with extremely
unlucky contents could cause us to loop forever on a bogus endless frame
pointer chain.
This review was triggered by much worse problems happening in some of
the other stack unwinding code.
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The scheduler on Andreas Friedrich's hyperthreading system stopped
working properly: the scheduler would never move tasks to another CPU!
The lask known working kernel was 2.6.8.
After a couple of attempts to corner the bug, the following smoking gun
was found:
BIOS reported wrong ACPI idfor the processor
CPU#1: set_cpus_allowed(), swapper:1, 3 -> 2
[<c0103bbe>] show_trace_log_lvl+0x34/0x4a
[<c0103ceb>] show_trace+0x2c/0x2e
[<c01045f8>] dump_stack+0x2b/0x2d
[<c0116a77>] set_cpus_allowed+0x52/0xec
[<c0101d86>] cpu_idle_wait+0x2e/0x100
[<c0259c57>] acpi_processor_power_exit+0x45/0x58
[<c0259752>] acpi_processor_remove+0x46/0xea
[<c025c6fb>] acpi_start_single_object+0x47/0x54
[<c025cee5>] acpi_bus_register_driver+0xa4/0xd3
[<c04ab2d7>] acpi_processor_init+0x57/0x77
[<c01004d7>] init+0x146/0x2fd
[<c0103a87>] kernel_thread_helper+0x7/0x10
a quick look at cpu_idle_wait() shows how broken that code is
on i386: it changes the init task's affinity map but never
restores it ...
and because all userspace tasks get forked by init, they all
inherited that single-CPU affinity mask. x86_64 cloned this
bug too.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Cc: Andreas Friedrich <andreas.friedrich@fujitsu-siemens.com>
Cc: Wolfgang Erig <Wolfgang.Erig@fujitsu-siemens.com>
Cc: Andrew Morton <akpm@osdl.org>
Cc: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Komuro reports that ISA interrupts do not work after a disable_irq(),
causing some PCMCIA drivers to not work, with messages like
eth0: Asix AX88190: io 0x300, irq 3, hw_addr xx:xx:xx:xx:xx:xx
eth0: found link beat
eth0: autonegotiation complete: 100baseT-FD selected
eth0: interrupt(s) dropped!
eth0: interrupt(s) dropped!
eth0: interrupt(s) dropped!
...
Linus Torvalds <torvalds@osdl.org> said:
"Now, edge-triggered interrupts are a _lot_ harder to mask, because the
Intel APIC is an unbelievable piece of sh*t, and has the edge-detect logic
_before_ the mask logic, so if a edge happens _while_ the device is
masked, you'll never ever see the edge ever again (unmasking will not
cause a new edge, so you simply lost the interrupt).
So when you "mask" an edge-triggered IRQ, you can't really mask it at all,
because if you did that, you'd lose it forever if the IRQ comes in while
you masked it. Instead, we're supposed to leave it active, and set a flag,
and IF the IRQ comes in, we just remember it, and mask it at that point
instead, and then on unmasking, we have to replay it by sending a
self-IPI."
This trivial patch solves the problem.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Cc: Ingo Molnar <mingo@redhat.com>
Acked-by: Komuro <komurojun-mbn@nifty.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* 'for-linus' of git://one.firstfloor.org/home/andi/git/linux-2.6:
[PATCH] x86-64: Fix race in exit_idle
[PATCH] x86-64: Fix vgetcpu when CONFIG_HOTPLUG_CPU is disabled
[PATCH] x86: Add acpi_user_timer_override option for Asus boards
[PATCH] x86-64: setup saved_max_pfn correctly (kdump)
[PATCH] x86-64: Handle reserve_bootmem_generic beyond end_pfn
[PATCH] x86-64: shorten the x86_64 boot setup GDT to what the comment says
[PATCH] x86-64: Fix PTRACE_[SG]ET_THREAD_AREA regression with ia32 emulation.
[PATCH] x86-64: Fix partial page check to ensure unusable memory is not being marked usable.
Revert "[PATCH] MMCONFIG and new Intel motherboards"
Fix interrupt routing for via 586 bridges. pirq can be 5 which needs to be
mapped to INTD. But currently the access functions can handle only pirq
1-4. this is similar to the other via chipsets where pirq 4 and 5 are both
mapped to INTD. Fixes bugzilla #7490
Cc: Daniel Paschka <monkey20181@gmx.net>
Cc: Adrian Bunk <bunk@susta.de>
Signed-off-by: Daniel Ritz <daniel.ritz@gmx.ch>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Timer overrides are normally disabled on Nvidia board because
they are commonly wrong, except on new ones with HPET support.
Unfortunately there are quite some Asus boards around that
don't have HPET, but need a timer override.
We don't know yet how to handle this transparently,
but at least add a command line option to force the timer override
and let them boot.
Cc: len.brown@intel.com
Signed-off-by: Andi Kleen <ak@suse.de>
This refactoring actually optimizes the code a little by caching the value
that we think the device is programmed with instead of reading it back from
the hardware. Which simplifies the code a little and should speed things up a
bit.
This patch introduces the concept of a ht_irq_msg and modifies the
architecture read/write routines to update this code.
There is a minor consistency fix here as well as x86_64 forgot to initialize
the htirq as masked.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Cc: Andi Kleen <ak@suse.de>
Acked-by: Bryan O'Sullivan <bos@pathscale.com>
Cc: <olson@pathscale.com>
Cc: Roland Dreier <rolandd@cisco.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
There are two bugs in the kretprobe-booster.
1) It doesn't make room for gs registers.
2) It doesn't change status of the current kprobe. This status will
effect the fault handling.
This patch fixes these bugs and, additionally, saves skipped registers for
compatibility with the original kretprobe.
Signed-off-by: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
o Currently there is no specific alignment restriction in linker script
and in some cases it can be placed non 4K aligned addresses. This fails
kexec which checks that segment to be loaded is page aligned.
o I guess, it does not harm data segment to be 4K aligned.
Signed-off-by: Vivek Goyal <vgoyal@in.ibm.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
If the microcode driver is built in (rather than module) there are some,
ehm, interesting effects happening due to the new "call out to userspace"
behavior that is introduced.. and which runs too early. The result is a
boot hang; which is really nasty.
The patch below is a minimally safe patch to fix this regression for 2.6.19
by just not requesting actual microcode updates during early boot. (That
is a good idea in general anyway)
The "real" fix is a lot more complex given the entire cpu hotplug scenario
(during cpu hotplug you normally need to load the microcode as well); but
the interactions for that are just really messy at this point; this fix at
least makes it work and avoids a full detangle of hotplug.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
arch/x86_64/kernel/cpufreq/../../../i386/kernel/cpu/cpufreq/speedstep-lib.c:131: error: 'MSR_FSB_FREQ' undeclared (first use in this function)
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Dave Jones <davej@redhat.com>
On some systems such as the IBM x3650 there are bits set in the
upper half of the control values provided by the _PSS object.
These bits are only relevant for cpufreq drivers that use IO ports
which are not currently supported by the speedstep-centrino driver.
The current MSR oriented code assumes that upper bits are not set
and thus fails to work correctly when they are. e.g. the control
and status value equality check fails even though the ACPI spec
allows the inequality.
Signed-off-by: Gary Hade <garyh@us.ibm.com>
Signed-off-by: Dave Jones <davej@redhat.com>
This reverts commit de09bddb9d. It tried
to reserve the MMCONFIG mmio memory ranges, but since the MMCONFIG
information is broken and often bogus (which is why we don't dare use it
most of the time _anyway_), it does more harm than good.
Cc: Jeff Chua <jeff.chua.linux@gmail.com>
Cc: Adrian Bunk <bunk@stusta.de>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Several more Intel CPUs are now capable using the p4-clockmod cpufreq
driver. As it is of limited use most of the time, print a big bold warning
if a better cpufreq driver might be available.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Dave Jones <davej@redhat.com>
Since the "mask" bit is in the low word, when we write a new entry, we
need to write the high word first, before we potentially unmask it.
The exception is when we actually want to mask the interrupt, in which
case we want to write the low word first to make sure that the high word
doesn't change while the interrupt routing is still active.
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This is preparation for fixing the ordering of the accesses that
got broken by the commit cf4c6a2f27 when
factoring out the "common" io apic routing entry accesses.
Move the accessor function (that were only used by io_apic.c) out
of a header file, and use proper memory-mapped accesses rather than
making up our own "volatile" pointers.
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
APM BIOS Interface Secification can now be found at
http://www.microsoft.com/whdc/archive/amp_12.mspx
Signed-off-by: Kristian Mueller <Kristian-M@Kristian-M.de>
Acked-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
efi_memory_present_wrapper() parameter start/end is physical address, but
function memory_present parameter is PFN, this patch converts physical
address to PFN.
Signed-off-by: bibo, mao <bibo.mao@intel.com>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* master.kernel.org:/pub/scm/linux/kernel/git/gregkh/pci-2.6:
PCI: Remove quirk_via_abnormal_poweroff
PCI: reset pci device state to unknown state for resume
PCI: x86-64: mmconfig missing printk levels
PCI: fix pci_fixup_video as it blows up on sparc64
acpiphp: fix latch status
Add a vmlinux.lds.h helper macro for defining the eight-level initcall table,
teach all the architectures to use it.
This is a prerequisite for a patch which performs initcall synchronisation for
multithreaded-probing.
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
[ Added AVR32 as well ]
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This reverts much of the original pci_fixup_video change and makes it
work for all arches that need it.
fixed, and tested on x86, x86_64 and IA64 dig.
Signed-off-by: Eiichiro Oiwa <eiichiro.oiwa.nm@hitachi.com>
Acked-by: David Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Jan convinced me that it was unnecessary because the assembly stubs do
this already on the stack.
Cc: jbeulich@novell.com
Signed-off-by: Andi Kleen <ak@suse.de>
The fake return address was being set to __KERNEL_PDA, rather than 0.
Push it earlier while %eax still equals 0.
Signed-off-by: Jeremy Fitzhardinge <jeremy@xensource.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Cc: Andi Kleen <ak@muc.de>
Cc: Andrew Morton <akpm@osdl.org>
This avoids some problems with gcc 4.x and earlier generating
invalid unwind information. In 4.1 the option is default
when unwind information is enabled.
And it seems to generate smaller code too, so it's probably
a good thing on its own. With gcc 4.0:
i386:
4683198 902112 480868 6066178 5c9002 vmlinux (before)
4449895 902112 480868 5832875 5900ab vmlinux (after)
x86-64:
4939761 1449584 648216 7037561 6b6279 vmlinux (before)
4854193 1449584 648216 6951993 6a1439 vmlinux (after)
On 4.1 it shouldn't make much difference because it is
default when unwind is enabled anyways.
Suggested by Michael Matz and Jan Beulich
Cc: jbeulich@novell.com
Signed-off-by: Andi Kleen <ak@suse.de>
This was copied, pasted but not edited.
Cc: Andi Kleen <ak@muc.de>
Cc: Jan Beulich <jbeulich@novell.com>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Andi Kleen <ak@suse.de>
acpi-cpufreq needs the same patch as the previous speedstep-centrino change.
Additionally, the centrino driver can have its ifdef moved out a little
further to eliminate some more code/variables.
Signed-off-by: Dave Jones <davej@redhat.com>
arch/i386/kernel/cpu/cpufreq/speedstep-centrino.c:396: warning: 'sw_any_bug_dmi_table' defined but not used
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Dave Jones <davej@redhat.com>
acpi-cpufreq.c, speedstep-centrino.c: warning: 'sw_any_bug_dmi_table' defined but not used
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Len Brown <len.brown@intel.com>
- Fixes a build problem with CONFIG_M386=y (include file dependencies get
messy).
- Share the implementation between x86 and x86_64
- These are too big to inline anyway.
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Len Brown <len.brown@intel.com>
Interrupts must be disabled during alternative instruction patching. On
systems with high timer IRQ rates, or when running in an emulator, timing
differences can result in random kernel panics because of running partially
patched instructions. This doesn't yet fix NMIs, which requires extricating
the patch code from the late bug checking and is logically separate (and also
less likely to cause problems).
Signed-off-by: Zachary Amsden <zach@vmware.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Separate out the concept of "queue congestion" from "backing-dev congestion".
Congestion is a backing-dev concept, not a queue concept.
The blk_* congestion functions are retained, as wrappers around the core
backing-dev congestion functions.
This proper layering is needed so that NFS can cleanly use the congestion
functions, and so that CONFIG_BLOCK=n actually links.
Cc: "Thomas Maier" <balagi@justmail.de>
Cc: "Jens Axboe" <jens.axboe@oracle.com>
Cc: Trond Myklebust <trond.myklebust@fys.uio.no>
Cc: David Howells <dhowells@redhat.com>
Cc: Peter Osterlund <petero2@telia.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Problem:
New Dell PowerEdge servers have 2 embedded ethernet ports, which are
labeled NIC1 and NIC2 on the chassis, in the BIOS setup screens, and
in the printed documentation. Assuming no other add-in ethernet ports
in the system, Linux 2.4 kernels name these eth0 and eth1
respectively. Many people have come to expect this naming. Linux 2.6
kernels name these eth1 and eth0 respectively (backwards from
expectations). I also have reports that various Sun and HP servers
have similar behavior.
Root cause:
Linux 2.4 kernels walk the pci_devices list, which happens to be
sorted in breadth-first order (or pcbios_find_device order on i386,
which most often is breadth-first also). 2.6 kernels have both the
pci_devices list and the pci_bus_type.klist_devices list, the latter
is what is walked at driver load time to match the pci_id tables; this
klist happens to be in depth-first order.
On systems where, for physical routing reasons, NIC1 appears on a
lower bus number than NIC2, but NIC2's bridge is discovered first in
the depth-first ordering, NIC2 will be discovered before NIC1. If the
list were sorted breadth-first, NIC1 would be discovered before NIC2.
A PowerEdge 1955 system has the following topology which easily
exhibits the difference between depth-first and breadth-first device
lists.
-[0000:00]-+-00.0 Intel Corporation 5000P Chipset Memory Controller Hub
+-02.0-[0000:03-08]--+-00.0-[0000:04-07]--+-00.0-[0000:05-06]----00.0-[0000:06]----00.0 Broadcom Corporation NetXtreme II BCM5708S Gigabit Ethernet (labeled NIC2, 2.4 kernel name eth1, 2.6 kernel name eth0)
+-1c.0-[0000:01-02]----00.0-[0000:02]----00.0 Broadcom Corporation NetXtreme II BCM5708S Gigabit Ethernet (labeled NIC1, 2.4 kernel name eth0, 2.6 kernel name eth1)
Other factors, such as device driver load order and the presence of
PCI slots at various points in the bus hierarchy further complicate
this problem; I'm not trying to solve those here, just restore the
device order, and thus basic behavior, that 2.4 kernels had.
Solution:
The solution can come in multiple steps.
Suggested fix#1: kernel
Patch below optionally sorts the two device lists into breadth-first
ordering to maintain compatibility with 2.4 kernels. It adds two new
command line options:
pci=bfsort
pci=nobfsort
to force the sort order, or not, as you wish. It also adds DMI checks
for the specific Dell systems which exhibit "backwards" ordering, to
make them "right".
Suggested fix#2: udev rules from userland
Many people also have the expectation that embedded NICs are always
discovered before add-in NICs (which this patch does not try to do).
Using the PCI IRQ Routing Table provided by system BIOS, it's easy to
determine which PCI devices are embedded, or if add-in, which PCI slot
they're in. I'm working on a tool that would allow udev to name
ethernet devices in ascending embedded, slot 1 .. slot N order,
subsort by PCI bus/dev/fn breadth-first. It'll be possible to use it
independent of udev as well for those distributions that don't use
udev in their installers.
Suggested fix#3: system board routing rules
One can constrain the system board layout to put NIC1 ahead of NIC2
regardless of breadth-first or depth-first discovery order. This adds
a significant level of complexity to board routing, and may not be
possible in all instances (witness the above systems from several
major manufacturers). I don't want to encourage this particular train
of thought too far, at the expense of not doing #1 or #2 above.
Feedback appreciated. Patch tested on a Dell PowerEdge 1955 blade
with 2.6.18.
You'll also note I took some liberty and temporarily break the klist
abstraction to simplify and speed up the sort algorithm. I think
that's both safe and appropriate in this instance.
Signed-off-by: Matt Domsch <Matt_Domsch@dell.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
pci_fixup_video turns into generic code because there are many platforms need this fixup
for embedded VGA as well as x86. The Video BIOS integrates into System BIOS on a machine
has embedded VGA although embedded VGA generally don't have PCI ROM. As a result,
embedded VGA need the way that the sysfs rom points to the Video BIOS of System
RAM (0xC0000). PCI-to-PCI Bridge Architecture specification describes the condition whether
or not PCI ROM forwards VGA compatible memory address. fixup_video suits this specification.
Although the Video ROM generally implements in x86 code regardless of platform, some
application such as X Window System can run this code by dosemu86. Therefore,
pci_fixup_video should turn into generic code.
Signed-off-by: Eiichiro Oiwa <eiichiro.oiwa.nm@hitachi.com>
Acked-by: Alan Cox <alan@redhat.com>
Acked-by: Jesse Barnes <jesse.barnes@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
If someone inserts speedstep-smi on a mobile P4, it prevents other cpufreq
modules from loading until it is unloaded.
Signed-off-by: Hiroshi Miura <miura@da-cha.org>
Signed-off-by: Dave Jones <davej@redhat.com>
ioremap must be balanced by an iounmap and failing to do so can result
in a memory leak.
Tested (compilation only):
- using allmodconfig
- making sure the files are compiling without any warning/error due to
new changes
Signed-off-by: Amol Lad <amol@verismonetworks.com>
Signed-off-by: Dave Jones <davej@redhat.com>
Introduce desc->name and eliminate the handle_irq_name() hack. Add
set_irq_chip_and_handler_name() to set the flow type and name at once.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Matthew Wilcox <willy@debian.org>
Cc: Kyle McMartin <kyle@mcmartin.ca>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Avoid possible PIT livelock issues seen on SMP systems (and reported by
Andi), by not allowing it as a clocksource on SMP boxes.
However, since the PIT may no longer be present, we have to properly handle
the cases where SMP systems have TSC skew and fall back from the TSC.
Since the PIT isn't there, it would "fall back" to the TSC again. So this
changes the jiffies rating to 1, and the TSC-bad rating value to 0.
Thus you will get the following behavior priority on i386 systems:
tsc [if present & stable]
hpet [if present]
cyclone [if present]
acpi_pm [if present]
pit [if UP]
jiffies
Rather then the current more complicated:
tsc [if present & stable]
hpet [if present]
cyclone [if present]
acpi_pm [if present]
pit [if cpus < 4]
tsc [if present & unstable]
jiffies
Signed-off-by: John Stultz <johnstul@us.ibm.com>
Cc: Andi Kleen <ak@suse.de>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Enable ondemand governor and acpi-cpufreq to use IA32_APERF and IA32_MPERF MSR
to get active frequency feedback for the last sampling interval. This will
make ondemand take right frequency decisions when hardware coordination of
frequency is going on.
Without APERF/MPERF, ondemand can take wrong decision at times due
to underlying hardware coordination or TM2.
Example:
* CPU 0 and CPU 1 are hardware cooridnated.
* CPU 1 running at highest frequency.
* CPU 0 was running at highest freq. Now ondemand reduces it to
some intermediate frequency based on utilization.
* Due to underlying hardware coordination with other CPU 1, CPU 0 continues to
run at highest frequency (as long as other CPU is at highest).
* When ondemand samples CPU 0 again next time, without actual frequency
feedback from APERF/MPERF, it will think that previous frequency change
was successful and can go to wrong target frequency. This is because it
thinks that utilization it has got this sampling interval is when running at
intermediate frequency, rather than actual highest frequency.
More information about IA32_APERF IA32_MPERF MSR:
Refer to IA-32 Intel® Architecture Software Developer's Manual at
http://developer.intel.com
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Dave Jones <davej@redhat.com>
Recent speedstep-centrino unification onto acpi-cpufreq patchset broke
cpuinfo_cur_freq interface in /sys/../cpuinfo/, when MSR was used for
transitions. Attached patch fixes that breakage.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Dave Jones <davej@redhat.com>
Only change the frequency if the state previously set is different
from what we are trying to set. We don't really have to get the current
frequency at this point.
Signed-off-by: Denis Sadykov <denis.m.sadykov@intel.com>
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Alexey Starikovskiy <alexey.y.starikovskiy@intel.com>
Signed-off-by: Dave Jones <davej@redhat.com>
Mark ACPI hooks in speedstep-centrino as deprecated. Change the order in which
speedstep-centrino and acpi-cpufreq (when both are in kernel) will be
added. First driver to be tried is now acpi-cpufreq, followed by
speedstep-centrino.
Add a note in feature-removal-schedule to mark this deprecation.
Signed-off-by: Denis Sadykov <denis.m.sadykov@intel.com>
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Alexey Starikovskiy <alexey.y.starikovskiy@intel.com>
Signed-off-by: Dave Jones <davej@redhat.com>
Add in the support for Intel Enhanced Speedstep - MSR based transitions.
With this change, the ACPI based support in speedstep-centrino can be
deprecated and duplicate code in that driver can be marked for removal.
Much easier to maintain and support this way. This also reduces the
user misconfigurations and questions on which driver is to be used
under which CPUs to support Enhanced Speedstep.
Signed-off-by: Denis Sadykov <denis.m.sadykov@intel.com>
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Alexey Starikovskiy <alexey.y.starikovskiy@intel.com>
Signed-off-by: Dave Jones <davej@redhat.com>
Some clean up and redsign of the driver. Mainly making it easier to add
support for multiple sub-mechanisms of changing frequency. Currently this
driver supports only ACPI SYSTEM_IO address space. With the changes
below it is easier to add support for other address spaces like Intel
Enhanced Speedstep which uses MSR (ACPI FIXED_FEATURE_HARDWARE) to do the
transitions.
Signed-off-by: Denis Sadykov <denis.m.sadykov@intel.com>
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Alexey Starikovskiy <alexey.y.starikovskiy@intel.com>
Signed-off-by: Dave Jones <davej@redhat.com>
This patchset has refresh/rebase of a bunch of patches/bugfixes related to
acpi-cpufreq that were sent earlier on this list.
patch 1/8
Patch that fixes a bug in swcoordination code in acpi-cpufreq
patch 2/8 through patch 7/8
Grand unification of ACPI based speedstep-centrino and acpi-cpufreq drivers.
ACPI allows P-state transitions in multiple ways. Like using IO ports or using
processor native method (MSR). Without this patch, IO port based P-state
transitions are handled in acpi-cpufreq driver and MSR based transitions on
Intel CPUs are handled in speedstep-centrino driver. Even though most of the
code in these two drivers should be similar, except for final changing/checking
of frequency (one driver does it using IO port and other does it through
MSR), we have duplicated code in these two drivers. There are also issues
around BIOSes supporting both MSR and IO port and which driver should be
loaded first in standard installations.
The patchset combines functionality of these two driver into acpi-cpufreq
driver. ACPI based functionality in speedstep-centrino is marked deprecated
and will be removed in future. speedstep-centrino will continue to work
on systems that depend on older non-ACPI table based P-state chanes.
* 2/8 - Patch that reorganizes the code in acpi-cpufreq, cleaning it up
a little and making it easier to add MSR support later.
* 3/8 - Pull in the MSR based transition support into acpi-cpufreq.
* 4/8 - Mark speedstep-centrino deprecated. Change the order in Makefile to
load acpi-cpufreq first and speedstep-centrino later, in cases where both
are configured in.
* 5/8 - lindent acpi-cpufreq.c
* 6/8 - Minor change to eliminate the check of current frequency on
notifications. We can use last set frequency instead.
* 7/8 - Make cpufreq->get of acpi_cpufreq work correctly again.
There will be a patch in future that removes ACPI based support in
speedstep-centrino in coming months.
patch 8/8
Add support for IA32_APERF and IA32_MPERF MSR and get the actual frequency
from these MSRs and use it to determine the next frequency target in ondemand
governor
This patch:
There is a bug in software coordination patch in acpi-cpufreq, due to which
frequency will only be set on first CPU of any coordinated group.
Bug identified by Denis, was not recognised earlier as there are no platforms
yet that use software coordination with acpi-cpufreq driver.
Signed-off-by: Denis Sadykov <denis.m.sadykov@intel.com>
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Dave Jones <davej@redhat.com>
The Linux group at Stratus Technologies has come across an issue with SCI
routing under ACPI. We were bitten by this when we made an x86_64 platform
whose BIOS provides an Interrupt Source Override for the SCI itself.
Apparently the override has no effect for the System Control Interrupt, and
this appears to be because of the way the SCI is setup in the ACPI code.
It does not handle the case where busirq != gsi.
The code that sets up the SCI routing assumes that bus irq == global irq.
So there is simply no provision for telling it otherwise. The attached
patch provides this mechanism.
This patch provided by David Bulkow, was tested on an i386 platform, which
does not use the SCI override, and also on an x86_64 platform which does
use an override.
Signed-off-by: David Bulkow <david.bulkow@stratus.com>
Cc: Andi Kleen <ak@muc.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Len Brown <len.brown@intel.com>
Intel processors starting with the Core Duo support
support processor native C-state using the MWAIT instruction.
Refer: Intel Architecture Software Developer's Manual
http://www.intel.com/design/Pentium4/manuals/253668.htm
Platform firmware exports the support for Native C-state to OS using
ACPI _PDC and _CST methods.
Refer: Intel Processor Vendor-Specific ACPI: Interface Specification
http://www.intel.com/technology/iapc/acpi/downloads/302223.htm
With Processor Native C-state, we use 'MWAIT' instruction on the processor
to enter different C-states (C1, C2, C3). We won't use the special IO
ports to enter C-state and no SMM mode etc required to enter C-state.
Overall this will mean better C-state support.
One major advantage of using MWAIT for all C-states is, with this and
"treat interrupt as break event" feature of MWAIT, we can now get accurate
timing for the time spent in C1, C2, .. states.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Len Brown <len.brown@intel.com>
Get rid of warning in the thermal throttling code about not checking
sysfs return values.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Apparently whoever converted voyager never actually checked that the
patch would compile ...
Remove as much of the pt_regs references as possible and move the
remaining ones into line with what's in x86 generic.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The implementation of genirq in x86 completely broke voyager (and
presumably visws). Since it's plugged into so much of the x86
infrastructure, you can't expect it to work unconverted.
This patch introduces a voyager IRQ handler type and switches voyager
to the genirq infrastructure.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Fix kernel-doc function name in usercopy.c.
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Implement the epoll_pwait system call, that extend the event wait mechanism
with the same logic ppoll and pselect do. The definition of epoll_pwait
is:
int epoll_pwait(int epfd, struct epoll_event *events, int maxevents,
int timeout, const sigset_t *sigmask, size_t sigsetsize);
The difference between the vanilla epoll_wait and epoll_pwait is that the
latter allows the caller to specify a signal mask to be set while waiting
for events. Hence epoll_pwait will wait until either one monitored event,
or an unmasked signal happen. If sigmask is NULL, the epoll_pwait system
call will act exactly like epoll_wait. For the POSIX definition of
pselect, information is available here:
http://www.opengroup.org/onlinepubs/009695399/functions/select.html
Signed-off-by: Davide Libenzi <davidel@xmailserver.org>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Andi Kleen <ak@muc.de>
Cc: Michael Kerrisk <mtk-manpages@gmx.net>
Cc: Ulrich Drepper <drepper@redhat.com>
Cc: Roland McGrath <roland@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Makes UML compile on any possible processor choice. The two problems were:
*) x86 code, when 386 is selected, checks at runtime boot_cpuflags, which we do
not have.
*) 3Dnow support for memcpy() et al. does not compile currently and fixing this
is not trivial, so simply disable it; with this change, if one selects MK7
UML compiles (while it did not).
Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Cc: Jeff Dike <jdike@addtoit.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
hw_interrupt_type is deprecated in favour of struct irq_chip.
[mingo@elte.hu: do x86_64 too]
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Arch-independent zone-sizing is using indices instead of symbolic names to
offset within an array related to zones (max_zone_pfns). The unintended
impact is that ZONE_DMA and ZONE_NORMAL is initialised on powerpc instead
of ZONE_DMA and ZONE_HIGHMEM when CONFIG_HIGHMEM is set. As a result, the
the machine fails to boot but will boot with CONFIG_HIGHMEM turned off.
The following patch properly initialises the max_zone_pfns[] array and uses
symbolic names instead of indices in each architecture using
arch-independent zone-sizing. Two users have successfully booted their
powerpcs with it (one an ibook G4). It has also been boot tested on x86,
x86_64, ppc64 and ia64. Please merge for 2.6.19-rc2.
Credit to Benjamin Herrenschmidt for identifying the bug and rolling the
first fix. Additional credit to Johannes Berg and Andreas Schwab for
reporting the problem and testing on powerpc.
Signed-off-by: Mel Gorman <mel@csn.ul.ie>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Which vector an irq is assigned to now varies dynamically and is
not needed outside of io_apic.c. So remove the possibility
of accessing the information outside of io_apic.c and remove
the silly macro that makes looking for users of irq_vector
difficult.
The fact this compiles ensures there aren't any more pieces
of the old CONFIG_PCI_MSI weirdness that I failed to remove.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
In commit ace80ab796 I removed the weird
logic that used the vector number as the irq number when MSI was
defined. However pci_enable_irq was using a different test in the
io_apic_assign_irqs path and I missed it :(
This patch removes the wrong code so no one hits this problem.
This code is only active when a specific set of boot command line
parameters is specified which likely explains why no one has notices
this earlier.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* git://git.infradead.org/~dhowells/irq-2.6:
IRQ: Maintain regs pointer globally rather than passing to IRQ handlers
IRQ: Typedef the IRQ handler function type
IRQ: Typedef the IRQ flow handler function type
CONFIG_M386 turns on spinlock-based generic rwsems - which surprises the
semaphore.S rwsem stubs. Tested both with and without CONFIG_M386.
Reported-by: Klaus Knopper <knopper@knopper.net>
Triaged-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andi Kleen <ak@suse.de>
Always make sure RIP/EIP is 0 in the registers stored on the top
of the stack of a kernel thread. This makes sure the unwinder code
won't try a fallback but knows the stack has ended.
AK: this patch is a bit mysterious. in theory they should be terminated
anyways, but it seems to fix at least one crash. Anyways double termination
probably doesn't hurt.
Signed-off-by: Andi Kleen <ak@suse.de>
Maintain a per-CPU global "struct pt_regs *" variable which can be used instead
of passing regs around manually through all ~1800 interrupt handlers in the
Linux kernel.
The regs pointer is used in few places, but it potentially costs both stack
space and code to pass it around. On the FRV arch, removing the regs parameter
from all the genirq function results in a 20% speed up of the IRQ exit path
(ie: from leaving timer_interrupt() to leaving do_IRQ()).
Where appropriate, an arch may override the generic storage facility and do
something different with the variable. On FRV, for instance, the address is
maintained in GR28 at all times inside the kernel as part of general exception
handling.
Having looked over the code, it appears that the parameter may be handed down
through up to twenty or so layers of functions. Consider a USB character
device attached to a USB hub, attached to a USB controller that posts its
interrupts through a cascaded auxiliary interrupt controller. A character
device driver may want to pass regs to the sysrq handler through the input
layer which adds another few layers of parameter passing.
I've build this code with allyesconfig for x86_64 and i386. I've runtested the
main part of the code on FRV and i386, though I can't test most of the drivers.
I've also done partial conversion for powerpc and MIPS - these at least compile
with minimal configurations.
This will affect all archs. Mostly the changes should be relatively easy.
Take do_IRQ(), store the regs pointer at the beginning, saving the old one:
struct pt_regs *old_regs = set_irq_regs(regs);
And put the old one back at the end:
set_irq_regs(old_regs);
Don't pass regs through to generic_handle_irq() or __do_IRQ().
In timer_interrupt(), this sort of change will be necessary:
- update_process_times(user_mode(regs));
- profile_tick(CPU_PROFILING, regs);
+ update_process_times(user_mode(get_irq_regs()));
+ profile_tick(CPU_PROFILING);
I'd like to move update_process_times()'s use of get_irq_regs() into itself,
except that i386, alone of the archs, uses something other than user_mode().
Some notes on the interrupt handling in the drivers:
(*) input_dev() is now gone entirely. The regs pointer is no longer stored in
the input_dev struct.
(*) finish_unlinks() in drivers/usb/host/ohci-q.c needs checking. It does
something different depending on whether it's been supplied with a regs
pointer or not.
(*) Various IRQ handler function pointers have been moved to type
irq_handler_t.
Signed-Off-By: David Howells <dhowells@redhat.com>
(cherry picked from 1b16e7ac850969f38b375e511e3fa2f474a33867 commit)
* master.kernel.org:/pub/scm/linux/kernel/git/davej/configh:
Remove all inclusions of <linux/config.h>
Manually resolved trivial path conflicts due to removed files in
the sound/oss/ subdirectory.
This moves the declarations for the architecture helpers into
include/linux/htirq.h from the generic include/linux/pci.h. Hopefully this
will make this distinction clearer.
htirq.h is included where it is needed.
The dependency on the msi code is fixed and removed.
The Makefile is tidied up.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Andi Kleen <ak@suse.de>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Greg KH <greg@kroah.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
It turns out msi_ops was simply not enough to abstract the architecture
specific details of msi. So I have moved the resposibility of constructing
the struct irq_chip to the architectures, and have two architecture specific
functions arch_setup_msi_irq, and arch_teardown_msi_irq.
For simple architectures those functions can do all of the work. For
architectures with platform dependencies they can call into the appropriate
platform code.
With this msi.c is finally free of assuming you have an apic, and this
actually takes less code.
The helpers for the architecture specific code are declared in the linux/msi.h
to keep them separate from the msi functions used by drivers in linux/pci.h
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Andi Kleen <ak@suse.de>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Greg KH <greg@kroah.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch implements two functions ht_create_irq and ht_destroy_irq for
use by drivers. Several other functions are implemented as helpers for
arch specific irq_chip handlers.
The driver for the card I tested this on isn't yet ready to be merged.
However this code is and hypertransport irqs are in use in a few other
places in the kernel. Not that any of this will get merged before 2.6.19
Because the ipath-ht400 is slightly out of spec this code will need to be
generalized to work there.
I think all of the powerpc uses are for a plain interrupt controller in a
chipset so support for native hypertransport devices is a little less
interesting.
However I think this is a half way decent model on how to separate arch
specific and generic helper code, and I think this is a functional model of
how to get the architecture dependencies out of the msi code.
[akpm@osdl.org: Kconfig fix]
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Cc: Greg KH <greg@kroah.com>
Cc: Andi Kleen <ak@muc.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
After raising the number of irqs the system supports this function is no
longer necessary.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Rajesh Shah <rajesh.shah@intel.com>
Cc: Andi Kleen <ak@muc.de>
Cc: "Protasevich, Natalie" <Natalie.Protasevich@UNISYS.com>
Cc: "Luck, Tony" <tony.luck@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch removes the change in behavior of the irq allocation code when
CONFIG_PCI_MSI is defined. Removing all instances of the assumption that irq
== vector.
create_irq is rewritten to first allocate a free irq and then to assign that
irq a vector.
assign_irq_vector is made static and the AUTO_ASSIGN case which allocates an
vector not bound to an irq is removed.
The ioapic vector methods are removed, and everything now works with irqs.
The definition of NR_IRQS no longer depends on CONFIG_PCI_MSI
[akpm@osdl.org: cleanup]
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Rajesh Shah <rajesh.shah@intel.com>
Cc: Andi Kleen <ak@muc.de>
Cc: "Protasevich, Natalie" <Natalie.Protasevich@UNISYS.com>
Cc: "Luck, Tony" <tony.luck@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This removes the hardcoded assumption that irq == vector in the msi
composition code, and it allows the msi message composition to setup logical
mode, or lowest priorirty delivery mode as we do for other apic interrupts,
and with the same selection criteria.
Basically this moves the problem of what is in the msi message into the
architecture irq management code where it belongs. Not in a generic layer
that doesn't have enough information to compose msi messages properly.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Rajesh Shah <rajesh.shah@intel.com>
Cc: Andi Kleen <ak@muc.de>
Cc: "Protasevich, Natalie" <Natalie.Protasevich@UNISYS.com>
Cc: "Luck, Tony" <tony.luck@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The current implementation of create_irq() is a hack but it is the current
hack that msi.c uses, and unfortunately the ``generic'' apic msi ops depend on
this hack. Thus we are stuck this hack of assuming irq == vector until the
depencencies in the generic msi code are removed.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Rajesh Shah <rajesh.shah@intel.com>
Cc: Andi Kleen <ak@muc.de>
Cc: "Protasevich, Natalie" <Natalie.Protasevich@UNISYS.com>
Cc: "Luck, Tony" <tony.luck@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Currently we attempt to predict how many irqs we will be able to allocate with
msi using pci_vector_resources and some complicated accounting, and then we
only allow each device as many irqs as we think are available on average.
Only the s2io driver even takes advantage of this feature all other drivers
have a fixed number of irqs they need and bail if they can't get them.
pci_vector_resources is inaccurate if anyone ever frees an irq. The whole
implmentation is racy. The current irq limit policy does not appear to make
sense with current drivers. So I have simplified things. We can revisit this
we we need a more sophisticated policy.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Rajesh Shah <rajesh.shah@intel.com>
Cc: Andi Kleen <ak@muc.de>
Cc: "Protasevich, Natalie" <Natalie.Protasevich@UNISYS.com>
Cc: "Luck, Tony" <tony.luck@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch converts all the i386 PIC controllers (except VisWS and Voyager,
which I could not test - but which should still work as old-style IRQ layers)
to the new and simpler irq-chip interrupt handling layer.
[akpm@osdl.org: build fix]
[mingo@elte.hu: enable fasteoi handler for i386 level-triggered IO-APIC irqs]
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Roland Dreier <rolandd@cisco.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This allows numaq to properly align cpus to their given node during
boot. Pass logical apicid to apicid_to_node and allow the summit
sub-arch to use physical apicid (hard_smp_processor_id()).
Tested against numaq and summit based systems with no issues.
Signed-off-by: Keith Mannthey <kmannth@us.ibm.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This changes a couple of if() BUG(); constructs to
BUG_ON(); so it can be safely optimized away.
Signed-off-by: Eric Sesterhenn <snakebyte@gmx.de>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Many files include the filename at the beginning, serveral used a wrong one.
Signed-off-by: Uwe Zeisberger <Uwe_Zeisberger@digi.com>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
The patch below corrects multiple occurances of "the the"
typos across several files, both in source comments and KConfig files.
There is no actual code changed, only text. Note this only affects the /arch
directory, and I believe I could find many more elsewhere. :)
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Jesper Juhl reported that testing the software math-emulation by forcing
"no387" doesn't work on modern CPU's.
The reason was two-fold:
- you also need to pass in "nofxsr" to make sure that we not only don't
touch the old i387 legacy hardware, it also needs to disable the
modern XMM/FXSR sequences
- "nofxsr" didn't actually clear the capability bits immediately,
leaving the early boot sequence still using FXSR until we got to
the identify_cpu() stage.
This fixes the "nofxsr" flag to take effect immediately on the boot CPU.
Debugging by Randy Dunlap
Acked-by: Randy Dunlap <rdunlap@xenotime.net>
Cc: Jesper Juhl <jesper.juhl@gmail.com>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This adds the new kernel_execve function on all architectures that were using
_syscall3() to implement execve.
The implementation uses code from the _syscall3 macros provided in the
unistd.h header file. I don't have cross-compilers for any of these
architectures, so the patch is untested with the exception of i386.
Most architectures can probably implement this in a nicer way in assembly or
by combining it with the sys_execve implementation itself, but this should do
it for now.
[bunk@stusta.de: m68knommu build fix]
[markh@osdl.org: build fix]
[bero@arklinux.org: build fix]
[ralf@linux-mips.org: mips fix]
[schwidefsky@de.ibm.com: s390 fix]
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Andi Kleen <ak@muc.de>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Ian Molton <spyro@f2s.com>
Cc: Mikael Starvik <starvik@axis.com>
Cc: David Howells <dhowells@redhat.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: Hirokazu Takata <takata.hirokazu@renesas.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Kyle McMartin <kyle@mcmartin.ca>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Kazumoto Kojima <kkojima@rr.iij4u.or.jp>
Cc: Richard Curnow <rc@rc0.org.uk>
Cc: William Lee Irwin III <wli@holomorphy.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Cc: Miles Bader <uclinux-v850@lsi.nec.co.jp>
Cc: Chris Zankel <chris@zankel.net>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Bernhard Rosenkraenzer <bero@arklinux.org>
Signed-off-by: Mark Haverkamp <markh@osdl.org>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
In some places, particularly drivers and __init code, the init utsns is the
appropriate one to use. This patch replaces those with a the init_utsname
helper.
Changes: Removed several uses of init_utsname(). Hope I picked all the
right ones in net/ipv4/ipconfig.c. These are now changed to
utsname() (the per-process namespace utsname) in the previous
patch (2/7)
[akpm@osdl.org: CIFS fix]
Signed-off-by: Serge E. Hallyn <serue@us.ibm.com>
Cc: Kirill Korotaev <dev@openvz.org>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Herbert Poetzl <herbert@13thfloor.at>
Cc: Andrey Savochkin <saw@sw.ru>
Cc: Serge Hallyn <serue@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Replace references to system_utsname to the per-process uts namespace
where appropriate. This includes things like uname.
Changes: Per Eric Biederman's comments, use the per-process uts namespace
for ELF_PLATFORM, sunrpc, and parts of net/ipv4/ipconfig.c
[jdike@addtoit.com: UML fix]
[clg@fr.ibm.com: cleanup]
[akpm@osdl.org: build fix]
Signed-off-by: Serge E. Hallyn <serue@us.ibm.com>
Cc: Kirill Korotaev <dev@openvz.org>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Herbert Poetzl <herbert@13thfloor.at>
Cc: Andrey Savochkin <saw@sw.ru>
Signed-off-by: Cedric Le Goater <clg@fr.ibm.com>
Cc: Jeff Dike <jdike@addtoit.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Move the init_nsproxy definition out of arch/ into kernel/nsproxy.c. This
avoids all arches having to be updated. Compiles and boots on s390.
Signed-off-by: Serge E. Hallyn <serue@us.ibm.com>
Cc: Kirill Korotaev <dev@openvz.org>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Herbert Poetzl <herbert@13thfloor.at>
Cc: Andrey Savochkin <saw@sw.ru>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch adds a nsproxy structure to the task struct. Later patches will
move the fs namespace pointer into this structure, and introduce a new utsname
namespace into the nsproxy.
The vserver and openvz functionality, then, would be implemented in large part
by virtualizing/isolating more and more resources into namespaces, each
contained in the nsproxy.
[akpm@osdl.org: build fix]
Signed-off-by: Serge Hallyn <serue@us.ibm.com>
Cc: Kirill Korotaev <dev@openvz.org>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Herbert Poetzl <herbert@13thfloor.at>
Cc: Andrey Savochkin <saw@sw.ru>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
cpumask: ensure that node_to_cpumask() is available to modules for all
supported combinations of architecture and CONFIG_NUMA.
Signed-off-by: Greg Banks <gnb@melbourne.sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
kprobe_flush_task() possibly calls kfree function during holding
kretprobe_lock spinlock, if kfree function is probed by kretprobe that will
incur spinlock deadlock. This patch moves kfree function out scope of
kretprobe_lock.
Signed-off-by: bibo, mao <bibo.mao@intel.com>
Signed-off-by: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Whitespace is used to indent, this patch cleans up these sentences by
kernel coding style.
Signed-off-by: bibo, mao <bibo.mao@intel.com>
Signed-off-by: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Cc: "Luck, Tony" <tony.luck@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
In an effort to make kprobe modules more portable, here is a patch that:
o Introduces the "symbol_name" field to struct kprobe.
The symbol->address resolution now happens in the kernel in an
architecture agnostic manner. 64-bit powerpc users no longer have
to specify the ".symbols"
o Introduces the "offset" field to struct kprobe to allow a user to
specify an offset into a symbol.
o The legacy mechanism of specifying the kprobe.addr is still supported.
However, if both the kprobe.addr and kprobe.symbol_name are specified,
probe registration fails with an -EINVAL.
o The symbol resolution code uses kallsyms_lookup_name(). So
CONFIG_KPROBES now depends on CONFIG_KALLSYMS
o Apparantly kprobe modules were the only legitimate out-of-tree user of
the kallsyms_lookup_name() EXPORT. Now that the symbol resolution
happens in-kernel, remove the EXPORT as suggested by Christoph Hellwig
o Modify tcp_probe.c that uses the kprobe interface so as to make it
work on multiple platforms (in its earlier form, the code wouldn't
work, say, on powerpc)
Signed-off-by: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Signed-off-by: Prasanna S Panchamukhi <prasanna@in.ibm.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
During tracking down a PAE compile failure, I found that config.h was being
included in a bunch of places in i386 code. It is no longer necessary, so
drop it.
Signed-off-by: Zachary Amsden <zach@vmware.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Jeremy Fitzhardinge <jeremy@xensource.com>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add a pte_update_hook which notifies about pte changes that have been made
without using the set_pte / clear_pte interfaces. This allows shadow mode
hypervisors which do not trap on page table access to maintain synchronized
shadows.
It also turns out, there was one pte update in PAE mode that wasn't using any
accessor interface at all for setting NX protection. Considering it is PAE
specific, and the accessor is i386 specific, I didn't want to add a generic
encapsulation of this behavior yet.
Signed-off-by: Zachary Amsden <zach@vmware.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Jeremy Fitzhardinge <jeremy@xensource.com>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Create a new PTE function which combines clearing a kernel PTE with the
subsequent flush. This allows the two to be easily combined into a single
hypercall or paravirt-op. More subtly, reverse the order of the flush for
kmap_atomic. Instead of flushing on establishing a mapping, flush on clearing
a mapping. This eliminates the possibility of leaving stale kmap entries
which may still have valid TLB mappings. This is required for direct mode
hypervisors, which need to reprotect all mappings of a given page when
changing the page type from a normal page to a protected page (such as a page
table or descriptor table page). But it also provides some nicer semantics
for real hardware, by providing extra debug-proofing against using stale
mappings, as well as ensuring that no stale mappings exist when changing the
cacheability attributes of a page, which could lead to cache conflicts when
two different types of mappings exist for the same page.
Signed-off-by: Zachary Amsden <zach@vmware.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Jeremy Fitzhardinge <jeremy@xensource.com>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Re-implement smp_send_nmi_allbutself() so that calls to smp_processor_id
(through send_IPI_allbutself) can be replaced with safe_smp_processor_id
without affecting other parts of the kernel (as suggested by Eric Biederman).
Signed-off-by: Fernando Vazquez <fernando@intellilink.co.jp>
Looks-reasonable-to: Andi Kleen <ak@muc.de>
Acked-by: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Vivek Goyal <vgoyal@in.ibm.com>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Substitute "smp_processor_id" with the stack overflow-safe
"safe_smp_processor_id" in the reboot path to the second kernel.
[akpm@osdl.org: build fix]
Signed-off-by: Fernando Vazquez <fernando@intellilink.co.jp>
Looks-reasonable-to: Andi Kleen <ak@muc.de>
Acked-by: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Vivek Goyal <vgoyal@in.ibm.com>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This is a the first of a series of patch-sets aiming at making kdump more
robust against stack overflows.
This patch set does the following:
* Add safe_smp_processor_id function to i386 architecture (this function was
inspired by the x86_64 function of the same name).
* Substitute "smp_processor_id" with the stack overflow-safe
"safe_smp_processor_id" in the reboot path to the second kernel.
This patch:
On the event of a stack overflow critical data that usually resides at the
bottom of the stack is likely to be stomped and, consequently, its use should
be avoided.
In particular, in the i386 and IA64 architectures the macro smp_processor_id
ultimately makes use of the "cpu" member of struct thread_info which resides
at the bottom of the stack. x86_64, on the other hand, is not affected by
this problem because it benefits from the use of the PDA infrastructure.
To circumvent this problem I suggest implementing "safe_smp_processor_id()"
(it already exists in x86_64) for i386 and IA64 and use it as a replacement
for smp_processor_id in the reboot path to the dump capture kernel. This is a
possible implementation for i386.
Signed-off-by: Fernando Vazquez <fernando@intellilink.co.jp>
Looks-reasonable-to: Andi Kleen <ak@muc.de>
Acked-by: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Vivek Goyal <vgoyal@in.ibm.com>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
With 2.6.18-rc4-mm2, now wall_jiffies will always be the same as jiffies.
So we can kill wall_jiffies completely.
This is just a cleanup and logically should not change any real behavior
except for one thing: RTC updating code in (old) ppc and xtensa use a
condition "jiffies - wall_jiffies == 1". This condition is never met so I
suppose it is just a bug. I just remove that condition only instead of
kill the whole "if" block.
[heiko.carstens@de.ibm.com: s390 build fix and cleanup]
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Cc: Andi Kleen <ak@muc.de>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Ian Molton <spyro@f2s.com>
Cc: Mikael Starvik <starvik@axis.com>
Cc: David Howells <dhowells@redhat.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: Hirokazu Takata <takata.hirokazu@renesas.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Kyle McMartin <kyle@mcmartin.ca>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Kazumoto Kojima <kkojima@rr.iij4u.or.jp>
Cc: Richard Curnow <rc@rc0.org.uk>
Cc: William Lee Irwin III <wli@holomorphy.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Cc: Miles Bader <uclinux-v850@lsi.nec.co.jp>
Cc: Chris Zankel <chris@zankel.net>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
All on stack DECLARE_COMPLETIONs should be replaced by:
DECLARE_COMPLETION_ONSTACK
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Acked-by: Ingo Molnar <mingo@elte.hu>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Clarify my (Pierre's) position on which GPL versions apply. The patch only
touches the source files where I am the only major author. The people who
have made the minor commits to the files have been contacted and have no
issues with this change.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
