>From now on FW will be downloaded from the binary file using request_firmware.
There will be different files for every supported chip. Currently 57710 (e1) and
57711 (e1h).
File names have the following format: bnx2x-<chip version>-<FW version>.fw.
ihex versions of current FW files are submitted in the next patch.
Each binary file has a header in the following format:
struct bnx2x_fw_file_section {
__be32 len;
__be32 offset;
}
struct bnx2x_fw_file_hdr {
struct bnx2x_fw_file_section init_ops;
struct bnx2x_fw_file_section init_ops_offsets;
struct bnx2x_fw_file_section init_data;
struct bnx2x_fw_file_section tsem_int_table_data;
struct bnx2x_fw_file_section tsem_pram_data;
struct bnx2x_fw_file_section usem_int_table_data;
struct bnx2x_fw_file_section usem_pram_data;
struct bnx2x_fw_file_section csem_int_table_data;
struct bnx2x_fw_file_section csem_pram_data;
struct bnx2x_fw_file_section xsem_int_table_data;
struct bnx2x_fw_file_section xsem_pram_data;
struct bnx2x_fw_file_section fw_version;
}
Each bnx2x_fw_file_section contains the length and the offset of the appropriate
section in the binary file. Values are stored in the big endian format.
Data types of arrays:
init_data __be32
init_ops_offsets __be16
XXsem_pram_data u8
XXsem_int_table_data u8
init_ops struct raw_op {
u8 op;
__be24 offset;
__be32 data;
}
fw_version u8
>From now boundaries of a specific initialization stage are stored in
init_ops_offsets array instead of being defined by separate macroes. The index
in init_ops_offsets is calculated by BLOCK_OPS_IDX macro:
#define BLOCK_OPS_IDX(block, stage, end) \
(2*(((block)*STAGE_IDX_MAX) + (stage)) + (end))
Security:
In addition to sanity check of array boundaries bnx2x will check a FW version.
Additional checks might be added in the future.
Signed-off-by: Vladislav Zolotarov <vladz@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for the Xilinx ll_temac 10/100/1000 Ethernet
device. The ll_temac ipcore is typically used on Xilinx Virtex and
Spartan designs attached to either a PowerPC 4xx or Microblaze
processor.
At the present moment, this driver only works with Virtex5 PowerPC
designs because it assumes DCR is used to access the DMA registers.
However, the low level access to DMA registers is abstracted and
it should be easy to adapt for the other implementations.
I'm posting this driver now as an RFC. There are still some things that
need to be tightened up, but it does appear to be stable.
Derived from driver code written by Yoshio Kashiwagi and David H. Lynch Jr.
Tested on Xilinx ML507 eval board with Base System Builder generated
FPGA design.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds an igbvf driver to handle virtual functions provided by the
igb driver when SR-IOV has been enabled. A virtual function is a
lightweight pci-e function that supports a single queue and shares
resources with the 82576 physical function contained within the igb
driver.
To spawn virtual functions from the igb driver all that is needed is to
enable CONFIG_PCI_IOV and have an 82576 Ethernet adapter on a system that
supports SR-IOV in the BIOS. The virtual functions will appear after the
interface is loaded.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ethoc indirectly uses crc32_le() and bitrev32(), so select
those library functions to be built.
drivers/built-in.o: In function `ethoc_set_multicast_list':
ethoc.c:(.text+0x6226f): undefined reference to `crc32_le'
ethoc.c:(.text+0x62276): undefined reference to `bitrev32'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Based on original patch by Ben Hutchings <ben@decadent.org.uk> and
Bastian Blank <waldi@debian.org>, with the following main changes:
Separated the mips firmware and rv2p firmware into different files
to make it easier to update them separately.
Added some code to fixup the rv2p code with run-time information
such as PAGE_SIZE.
Update version to 2.0.0.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Kconfig and Makefile related changes for vxge driver.
- No changes in current submission.
- Changes from previous submission -
- Incorporated the following review comments as per Bill Flink:
- Add dependancy on INET along with PCI
- Remove dependancy on INET_LRO and add GRO support.
- Made this patch as last patch as per Ben Hutchings comments.
Signed-off-by: Sivakumar Subramani <sivakumar.subramani@neterion.com>
Signed-off-by: Rastapur Santosh <santosh.rastapur@neterion.com>
Signed-off-by: Ramkrishna Vepa <ram.vepa@neterion.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Let driver depend on HAS_IOMEM to avoid build breakage on s390:
CC drivers/net/ethoc.o
drivers/net/ethoc.c: In function 'ethoc_read':
drivers/net/ethoc.c:221: error: implicit declaration of function 'ioread32'
drivers/net/ethoc.c: In function 'ethoc_write':
drivers/net/ethoc.c:226: error: implicit declaration of function 'iowrite32'
drivers/net/ethoc.c: In function 'ethoc_rx':
drivers/net/ethoc.c:405: error: implicit declaration of function 'memcpy_fromio'
drivers/net/ethoc.c: In function 'ethoc_start_xmit':
drivers/net/ethoc.c:828: error: implicit declaration of function 'memcpy_toio'
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Acked-by: Thierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a platform device driver that supports the OpenCores 10/100
Mbps Ethernet MAC.
The driver expects three resources: one IORESOURCE_MEM resource defines the
memory region for the core's memory-mapped registers while a second
IORESOURCE_MEM resource defines the network packet buffer space. The third
resource, of type IORESOURCE_IRQ, associates an interrupt with the driver.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Acked-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that most network device drivers in (all but one in x86_64 allmodconfig)
support net_device_ops. Expose it as a configuration parameter. Still
need to address even older 32 bit drivers, and other arch before
compatiablity can be scheduled for removal in some future release.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Driver for Dave DNET ethernet controller found on Dave/DENX QongEVB-LITE
FPGA. Heavily based on Dave sources, I've just adopted it to current
kernel version and done some code cleanup.
Signed-off-by: Ilya Yanok <yanok@emcraft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To match ixgbe GRO functionality, we remove the LRO (which is now GRO)
Kconfig option which enables GRO by default.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Controlled by a compile-time (Kconfig) option for now, since it
isn't a win in all cases.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MDIO bus drivers for the UCC and gianfar ethernet controllers are
essentially the same. There's no reason to duplicate that much code.
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch makes cxgb3 invoke the GRO hooks instead of LRO. As
GRO has a compatible external interface to LRO this is a very
straightforward replacement.
I've kept the ioctl controls for per-queue LRO switches. However,
we should not encourage anyone to use these.
Because of that, I've also kept the skb construction code in
cxgb3. Hopefully we can phase out those per-queue switches
and then kill this too.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Acked-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch makes igb invoke the GRO hooks instead of LRO. As
GRO has a compatible external interface to LRO this is a very
straightforward replacement.
Three things of note:
1) I've kept the LRO Kconfig option until we decide to enable
GRO across the board at which point it can also be killed.
2) The poll_controller stuff is broken in igb as it tries to do
the same work as the normal poll routine. Since poll_controller
can be called in the middle of a poll, this can't be good.
I noticed this because poll_controller can invoke the GRO hooks
without flushing held GRO packets.
However, this should be harmless (assuming the poll_controller
bug above doesn't kill you first :) since the next ->poll will
clear the backlog. The only time when we'll have a problem is
if we're already executing the GRO code on the same ring, but
that's no worse than what happens now.
3) I kept the ip_summed check before calling GRO so that we're
on par with previous behaviour.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch makes ixgbe invoke the GRO hooks instead of LRO. As
GRO has a compatible external interface to LRO this is a very
straightforward replacement.
As GRO uses the napi structure to track the held packets, I've
modified the code paths involved to pass that along.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
We do not depend on EXPERIMENTAL and the driver is
not experimental, so remove this warning.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Integrate the i2400m driver into the kernel's build and Kconfig.
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
cxgb3i requires the cxgb3 net driver, so it selects it. However,
cxgb3 has dependencies which the select cannot see. Fix this by
separating out the cxgb3 dependencies into a separate hidden config
option (CONFIG_CHELSIO_T3_DEPENDS) and make both cxgb3 and cxgb3i
depend on it.
Reported-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Karen Xie <kxie@chelsio.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
I noticed it isn't possible to build token ring & fddi drivers
without causing LLC, and a bunch of other things to be forced
built-in. For distro kernels, this means carrying a chunk of
code in the vmlinuz, even if the user doesn't use those protocols.
Signed-off-by: Dave Jones <davej@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The code appears to be dead: nobody call these functions, plus build
breaks when UGETH_FILTERING is enabled:
ucc_geth.c:1848: warning: 'struct enet_addr' declared inside parameter list
ucc_geth.c:1848: warning: its scope is only this definition or declaration, which is probably not what you want
ucc_geth.c: In function 'ugeth_82xx_filtering_get_match_addr_in_hash':
ucc_geth.c:1856: error: dereferencing pointer to incomplete type
ucc_geth.c:1874: error: dereferencing pointer to incomplete type
ucc_geth.c:1877: warning: return from incompatible pointer type
ucc_geth.c: At top level:
ucc_geth.c:1885: warning: 'struct enet_addr' declared inside parameter list
ucc_geth.c: In function 'ugeth_82xx_filtering_add_addr_in_hash':
ucc_geth.c:1894: error: dereferencing pointer to incomplete type
ucc_geth.c:1909: warning: passing argument 2 of 'ugeth_82xx_filtering_get_match_addr_in_hash' from incompatible pointer type
ucc_geth.c:1909: warning: assignment from incompatible pointer type
ucc_geth.c:1918: error: dereferencing pointer to incomplete type
ucc_geth.c: At top level:
ucc_geth.c:1928: warning: 'struct enet_addr' declared inside parameter list
ucc_geth.c: In function 'ugeth_82xx_filtering_clear_addr_in_hash':
ucc_geth.c:1947: warning: passing argument 2 of 'ugeth_82xx_filtering_get_match_addr_in_hash' from incompatible pointer type
ucc_geth.c:1947: warning: assignment from incompatible pointer type
ucc_geth.c:1954: error: dereferencing pointer to incomplete type
ucc_geth.c: At top level:
ucc_geth.c:2060: warning: 'struct enet_addr' declared inside parameter list
ucc_geth.c: In function 'ugeth_82xx_filtering_add_addr_in_paddr':
ucc_geth.c:2064: error: dereferencing pointer to incomplete type
ucc_geth.c:2073: error: dereferencing pointer to incomplete type
ucc_geth.c:2075: warning: passing argument 2 of 'hw_add_addr_in_paddr' from incompatible pointer type
make[2]: *** [ucc_geth.o] Error 1
The code is there since the driver was merged, and nobody seem to be
interested in fixing or actually using it. If we ever want the
filtering support, we can always revert the patch and fix it, but so
far it just draws reader's attention.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a driver for the LAN9240 PCI ethernet adapter.
Changes since initial submission:
- debug msg_level has been changed to use standard definitions
- convert to use net_device_ops
Signed-off-by: Steve Glendinning <steve.glendinning@smsc.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since the netlink option for DCB is necessary to actually be useful,
simplified the Kconfig option. In addition, added useful help text for the
Kconfig option.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds support for Data Center Bridging (DCB) features in the ixgbe
driver and adds an rtnetlink interface for configuring DCB to the
kernel. The DCB feature support included are Priority Grouping (PG) -
which allows bandwidth guarantees to be allocated to groups to traffic
based on the 802.1q priority, and Priority Based Flow Control (PFC) -
which introduces a new MAC control PAUSE frame which works at
granularity of the 802.1p priority instead of the link (IEEE 802.3x).
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the 82576 device to the description for igb in Kconfig.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Without this patch it is possible to select drivers which require
bestcomm support without bestcomm support being selected. This
patch reworks the bestcomm dependencies to ensure the correct
bestcomm tasks are always enabled.
Reported-by: Hans Lehmann <hans.lehmann@ritter-elektronik.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Attached is a driver for SMSC's LAN911x and LAN921x families of embedded
ethernet controllers.
There is an existing smc911x driver in the tree; this is intended to
replace it. Dustin McIntire (the author of the smc911x driver) has
expressed his support for switching to this driver.
This driver contains workarounds for all known hardware issues, and has
been tested on all flavours of the chip on multiple architectures.
This driver now uses phylib, so this patch also adds support for the
device's internal phy
Signed-off-by: Steve Glendinning <steve.glendinning@smsc.com>
Signed-off-by: Bahadir Balban <Bahadir.Balban@arm.com>
Signed-off-by: Dustin Mcintire <dustin@sensoria.com>
Signed-off-by: Bill Gatliff <bgat@billgatliff.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This patch adds better IPv6 failover support for bonding devices,
especially when in active-backup mode and there are only IPv6 addresses
configured, as reported by Alex Sidorenko.
- Creates a new file, net/drivers/bonding/bond_ipv6.c, for the
IPv6-specific routines. Both regular bonds and VLANs over bonds
are supported.
- Adds a new tunable, num_unsol_na, to limit the number of unsolicited
IPv6 Neighbor Advertisements that are sent on a failover event.
Default is 1.
- Creates two new IPv6 neighbor discovery functions:
ndisc_build_skb()
ndisc_send_skb()
These were required to support VLANs since we have to be able to
add the VLAN id to the skb since ndisc_send_na() and friends
shouldn't be asked to do this. These two routines are basically
__ndisc_send() split into two pieces, in a slightly different order.
- Updates Documentation/networking/bonding.txt and bumps the rev of bond
support to 3.4.0.
On failover, this new code will generate one packet:
- An unsolicited IPv6 Neighbor Advertisement, which helps the switch
learn that the address has moved to the new slave.
Testing has shown that sending just the NA results in pretty good
behavior when in active-back mode, I saw no lost ping packets for example.
Signed-off-by: Brian Haley <brian.haley@hp.com>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The bool kconfig option added to ixgbe and myri10ge for DCA is ambigous,
so this patch adds a description to the kconfig option.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (29 commits)
tcp: Restore ordering of TCP options for the sake of inter-operability
net: Fix disjunct computation of netdev features
sctp: Fix to handle SHUTDOWN in SHUTDOWN_RECEIVED state
sctp: Fix to handle SHUTDOWN in SHUTDOWN-PENDING state
sctp: Add check for the TSN field of the SHUTDOWN chunk
sctp: Drop ICMP packet too big message with MTU larger than current PMTU
p54: enable 2.4/5GHz spectrum by eeprom bits.
orinoco: reduce stack usage in firmware download path
ath5k: fix suspend-related oops on rmmod
[netdrvr] fec_mpc52xx: Implement polling, to make netconsole work.
qlge: Fix MSI/legacy single interrupt bug.
smc911x: Make the driver safer on SMP
smc911x: Add IRQ polarity configuration
smc911x: Allow Kconfig dependency on ARM
sis190: add identifier for Atheros AR8021 PHY
8139x: reduce message severity on driver overlap
igb: add IGB_DCA instead of selecting INTEL_IOATDMA
igb: fix tx data corruption with transition to L0s on 82575
ehea: Fix memory hotplug support
netdev: DM9000: remove BLACKFIN hacking in DM9000 netdev driver
...
* git://git.kernel.org/pub/scm/linux/kernel/git/czankel/xtensa-2.6:
xtensa: Add config files for Diamond 232L - Rev B processor variant
xtensa: Fix io regions
xtensa: Add support for the Sonic Ethernet device for the XT2000 board.
xtensa: replace remaining __FUNCTION__ occurrences
xtensa: use newer __SPIN_LOCK_UNLOCKED macro
XTENSA: warn about including <asm/rwsem.h> directly.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
IB/ehca: Reject dynamic memory add/remove when ehca adapter is present
IB/ehca: Fix reported max number of QPs and CQs in systems with >1 adapter
IPoIB: Set netdev offload features properly for child (VLAN) interfaces
IPoIB: Clean up ethtool support
mlx4_core: Add Ethernet PCI device IDs
mlx4_en: Add driver for Mellanox ConnectX 10GbE NIC
mlx4_core: Multiple port type support
mlx4_core: Ethernet MAC/VLAN management
mlx4_core: Get ethernet MTU and default address from firmware
mlx4_core: Support multiple pre-reserved QP regions
Update NetEffect maintainer emails to Intel emails
RDMA/cxgb3: Remove cmid reference on tid allocation failures
IB/mad: Use krealloc() to resize snoop table
IPoIB: Always initialize poll_timer to avoid crash on unload
IB/ehca: Don't allow creating UC QP with SRQ
mlx4_core: Add QP range reservation support
RDMA/ucma: Test ucma_alloc_multicast() return against NULL, not with IS_ERR()
The Mellanox ConnectX can operate as an InfiniBand adapter, as an
Ethernet NIC, or as a Fibre Channel (FC) HBA. The kernel has a
low-level driver, mlx4_core, which handles multiplexing access to the
device, and there is also already an InfiniBad driver, mlx4_ib.
This patch adds a new driver, mlx4_en, which implements a standard
Ethernet NIC driver.
Signed-off-by: Liran Liss <liranl@mellanox.co.il>
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Since more ARM platforms use this device, it is easier to add a
dependency on ARM rather than individual platforms.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Add a bool IGB_DCA defined to y if IGB and DCA are enabled, but IGB isn't y while DCA=m. And thus remove the need to select INTEL_IOATDMA when IGB is enabled, so that non-x86 architectures can build the igb driver.
Based on work/patch from Brice Goglin <brice@myri.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
RBTX4939 board has SMC91X chip and there can be other MIPS boards with
that chip. Make SMC91X selectable on all MIPS board would be better than
enumerating each boards in Kconfig.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Cc: jeff@garzik.org
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
We cannot select INTEL_IOATDMA in Kconfig as soon as MYRI10GE or IXGBE
is enabled since the former is not available on all architectures.
Just use a Kconfig bool {IXGBE,MYRI10GE}_DCA set to =y when DCA
support can actually be built.
[myri10ge portion written and signed-off-by] Brice Goglin <brice@myri.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
I don't think the enic driver has anything to do with Mark Everett
(http://en.wikipedia.org/wiki/A_Man_Called_E). Fix the Kconfig
description.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm: (236 commits)
[ARM] 5300/1: fixup spitz reset during boot
[ARM] 5295/1: make ZONE_DMA optional
[ARM] 5239/1: Palm Zire 72 power management support
[ARM] 5298/1: Drop desc_handle_irq()
[ARM] 5297/1: [KS8695] Fix two compile-time warnings
[ARM] 5296/1: [KS8695] Replace macro's with trailing underscores.
[ARM] pxa: allow multi-machine PCMCIA builds
[ARM] pxa: add preliminary CPUFREQ support for PXA3xx
[ARM] pxa: add missing ACCR bit definitions to pxa3xx-regs.h
[ARM] pxa: rename cpu-pxa.c to cpufreq-pxa2xx.c
[ARM] pxa/zylonite: add support for USB OHCI
[ARM] ohci-pxa27x: use ioremap() and offset for register access
[ARM] ohci-pxa27x: introduce pxa27x_clear_otgph()
[ARM] ohci-pxa27x: use platform_get_{irq,resource} for the resource
[ARM] ohci-pxa27x: move OHCI controller specific registers into the driver
[ARM] ohci-pxa27x: introduce flags to avoid direct access to OHCI registers
[ARM] pxa: move I2S register and bit definitions into pxa2xx-i2s.c
[ARM] pxa: simplify DMA register definitions
[ARM] pxa: make additional DCSR bits valid for PXA3xx
[ARM] pxa: move i2c register and bit definitions into i2c-pxa.c
...
Fixed up conflicts in
arch/arm/mach-versatile/core.c
sound/soc/pxa/pxa2xx-ac97.c
sound/soc/pxa/pxa2xx-i2s.c
manually.
Remove the EXPERIMENTAL label from the atl1 driver and change the vendor
name to include Attansic's successor, Atheros. We'll leave Attansic in
the name since Attansic's PCI ID (1969) is encoded in the PCI config and
is what users encounter on their systems.
Signed-off-by: Jay Cliburn <jacliburn@bellsouth.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for i.MX31ADS board to the cs89x0 ethernet driver.
Rework Kconfig options for the cs89x0 driver to reduce the #ifdef
clutter.
Signed-off-by: Gilles Chanteperdrix <gilles.chanteperdrix@xenomai.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Since the e1000/e1000e split, no hardware supported by e1000
supports packet split, just remove the Kconfig option and associated
code from the driver.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Now that arch/ppc is dead CONFIG_PPC_MERGE is always defined for all
powerpc platforms so we don't need to depend on it.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Cc: David Gibson <david@gibson.dropbear.id.au>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Use DCA in myri10ge when CONFIG_DCA_MODULE is set as well.
And thus force INTEL_IOATDMA to =y so that DCA=y if we are =y.
Signed-off-by: Brice Goglin <brice@myri.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
drivers/built-in.o: In function `rtl8169_gset_xmii':
r8169.c:(.text+0x82259): undefined reference to `mii_ethtool_gset'
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Acked-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Edward Hsu <edward_hsu@realtek.com.tw>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
ixgbe can depend on dca IF it is enabled. So if we are compiled as
IXGBE=y, and DCA is enabled, then we must force INTEL_IOATDMA and therefore
DCA to be =y also.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Switch mv643xx_eth from using drivers/net/mii.c to using phylib.
Since the mv643xx_eth hardware does all the link state handling and
PHY polling, the driver will use phylib in the "Doing it all yourself"
mode described in the phylib documentation.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Acked-by: Andy Fleming <afleming@freescale.com>
Driver for Atheros L2 10/100 network device. Includes necessary
changes for Kconfig, Makefile, and pci_ids.h.
Signed-off-by: Chris Snook <csnook@redhat.com>
Signed-off-by: Jay Cliburn <jacliburn@bellsouth.net>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
so update things accordingly
Signed-off-by: Mike Frysinger <vapier.adi@gmail.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
After some cleanups in arch/mips area, now MACH_TX49XX is selected for
both TOSHIBA_RBTX4927 and TOSHIBA_RBTX4938. Fold these two conditions
to one.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Add support SH7619 Internal ethernet controler.
Signed-off-by: Yoshinori Sato <ysato@users.sourceforge.jp>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
SH7763 has Ethernet core same as SH7710/SH7712.
Positions of some registry are different, but the basic part is the same.
I add support of ethernet of sh7763 to sh_eth.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Full patch for the Atheros L1E Gigabit Ethernet driver.
Supportring AR8121, AR8113 and AR8114
Signed-off-by: Jie Yang <jie.yang @atheros.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (1232 commits)
iucv: Fix bad merging.
net_sched: Add size table for qdiscs
net_sched: Add accessor function for packet length for qdiscs
net_sched: Add qdisc_enqueue wrapper
highmem: Export totalhigh_pages.
ipv6 mcast: Omit redundant address family checks in ip6_mc_source().
net: Use standard structures for generic socket address structures.
ipv6 netns: Make several "global" sysctl variables namespace aware.
netns: Use net_eq() to compare net-namespaces for optimization.
ipv6: remove unused macros from net/ipv6.h
ipv6: remove unused parameter from ip6_ra_control
tcp: fix kernel panic with listening_get_next
tcp: Remove redundant checks when setting eff_sacks
tcp: options clean up
tcp: Fix MD5 signatures for non-linear skbs
sctp: Update sctp global memory limit allocations.
sctp: remove unnecessary byteshifting, calculate directly in big-endian
sctp: Allow only 1 listening socket with SO_REUSEADDR
sctp: Do not leak memory on multiple listen() calls
sctp: Support ipv6only AF_INET6 sockets.
...
Looking at older kernel sources the APOLLO_ELPLUS option was added
somewhere during kernel 2.1, but even kernel 2.2.0 does not contain
any driver that would be enabled through it...
Reported-by: Robert P. J. Day <rpjday@crashcourse.ca>
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The only user of the board, the extremly dated and rare MIPS Atlas board,
has been removed, so this driver can go, too.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This patch adds support for the use of the inet_lro module to provide
software LRO support.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
network maintainers suggest NAPI only drivers are the only way to go.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Support for the at91sam9g20 : Atmel 400Mhz ARM 926ej-s SOC.
AT91sam9g20 is an evolution of the at91sam9260 with a faster clock
speed.
We created a new board for this device but based the chip support
directly on 9260 files with little updates.
Here is the chip page on Atmel wabsite:
http://atmel.com/dyn/products/product_card.asp?part_id=4337
Signed-off-by: Sedji Gaouaou <sedji.gaouaou@atmel.com>
Signed-off-by: Justin Waters <justin.waters@timesys.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
It will almost unavoidably cause some breakage but it
is long overdue.
The driver identification string has been updated, a
lost tabulation and some unused code have been removed.
Otherwise the code paths should stay the same.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Edward Hsu <edward_hsu@realtek.com.tw>
We do not want to prolong the situation much longer that e1000
and e1000e support these devices at the same time. As a result,
take out the bandage that was added for the interim period
and remove all the PCI Express device IDs from e1000.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Support for in-kernel LRO with the ability to enable/disable via ethtool
based on comments from Ben Hutchings.
Signed-off-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: PJ Waskiewicz <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The ENC28J60 driver ended up adding itself inbetween the
two DM9000 Kconfig entries, so re-unite the two together.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The DM9000's internal PHY reports a copy of the link status
in the NSR register of the chip. Reading the status when
polling for link status is faster as it eliminates the need
to sleep, but does not print as much information.
Add an platform flag to force this behaviour, and a Kconfig
option to allow it to be forced to the faster method always.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Supporting the 57711 and 57711E - refers to in the code as E1H. The
57710 is referred to as E1.
To support the new members in the family, the bnx2x structure was
divided to 3 parts: common, port and function. These changes caused some
rearrangement in the bnx2x.h file.
A set of accessories macros were added to make access to the bnx2x
structure more readable
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The arch/ppc sub-tree has been removed in the powerpc git tree. The old
ibm_emac driver is no longer used by anything as a result of this. This
removes it, leaving the ibm_newemac driver as the proper driver to use for
PowerPC boards with the EMAC hardware.
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Add support for Renesas SuperH Ethernet controller. This driver supports
SH7710 and SH7712.
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Enable the smc911x driver for the SuperH architecture. While at it remove
the unused SMC_USE_SH_DMA definition.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Now that walk_memory_resource() is available regardless of
MEMORY_HOTPLUG's setting, this dependency is not needed.
Signed-off-by: Nathan Lynch <ntl@pobox.com>
Acked-by: Jeff Garzik <jeff@garzik.org>
Acked-by: Yasunori Goto <y-goto@jp.fujitsu.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
As the driver has the standard way to handle PSK, deprecate the old
interface.
Signed-off-by: Masakazu Mokuno <mokuno@sm.sony.co.jp>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
cxgb3 uses lro_* functions and selects INET_LRO, but this doesn't help unless
INET is already enabled, so make the driver depend on INET also.
sge.c:(.text+0x9f09a): undefined reference to `lro_flush_all'
sge.c:(.text+0x9f62f): undefined reference to `lro_receive_skb'
sge.c:(.text+0x9f8a3): undefined reference to `lro_receive_frags'
sge.c:(.text+0x9fbe0): undefined reference to `lro_vlan_hwaccel_receive_skb'
sge.c:(.text+0x9ffcd): undefined reference to `lro_vlan_hwaccel_receive_frags'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Make this driver compile cleanly on 64 bit platforms.
Compile tested only.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This patch introduces code to register and unregister the tg3 mdio bus
with the system.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This driver has been superseded by fs_enet and is no longer in use.
Signed-off-by: Becky Bruce <becky.bruce@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The new ehea memory hot plug implementation depends on MEMORY_HOTPLUG.
Signed-off-by: Hannes Hering <hering2@de.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Delete the non-napi code from the driver and Kconfig.
Tested x86_64. Apply at next open opportunity.
Signed-off-by: Don Fry <pcnet32@verizon.net>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (53 commits)
tcp: Overflow bug in Vegas
[IPv4] UFO: prevent generation of chained skb destined to UFO device
iwlwifi: move the selects to the tristate drivers
ipv4: annotate a few functions __init in ipconfig.c
atm: ambassador: vcc_sf semaphore to mutex
MAINTAINERS: The socketcan-core list is subscribers-only.
netfilter: nf_conntrack: padding breaks conntrack hash on ARM
ipv4: Update MTU to all related cache entries in ip_rt_frag_needed()
sch_sfq: use del_timer_sync() in sfq_destroy()
net: Add compat support for getsockopt (MCAST_MSFILTER)
net: Several cleanups for the setsockopt compat support.
ipvs: fix oops in backup for fwmark conn templates
bridge: kernel panic when unloading bridge module
bridge: fix error handling in br_add_if()
netfilter: {nfnetlink,ip,ip6}_queue: fix skb_over_panic when enlarging packets
netfilter: x_tables: fix net namespace leak when reading /proc/net/xxx_tables_names
netfilter: xt_TCPOPTSTRIP: signed tcphoff for ipv6_skip_exthdr() retval
tcp: Limit cwnd growth when deferring for GSO
tcp: Allow send-limited cwnd to grow up to max_burst when gso disabled
[netdrvr] gianfar: Determine TBIPA value dynamically
...
The driver supports the 10Xpress PHY and XFP modules on our reference
designs SFE4001 and SFE4002 and the SMC models SMC10GPCIe-XFP and
SMC10GPCIe-10BT.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The platform is actually named routerboard 532 so let's call it this.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Acked-by: Jeff Garzik <jeff@garzik.org>
... and isn't possible on sparc32 boxen anyway, unless somebody
had done JavaStation with PCIE lately.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc: (49 commits)
[POWERPC] Add zImage.iseries to arch/powerpc/boot/.gitignore
[POWERPC] bootwrapper: fix build error on virtex405-head.S
[POWERPC] 4xx: Fix 460GT support to not enable FPU
[POWERPC] 4xx: Add NOR FLASH entries to Canyonlands and Glacier dts
[POWERPC] Xilinx: of_serial support for Xilinx uart 16550.
[POWERPC] Xilinx: boot support for Xilinx uart 16550.
[POWERPC] celleb: Add support for PCI Express
[POWERPC] celleb: Move miscellaneous files for Beat
[POWERPC] celleb: Move a file for SPU on Beat
[POWERPC] celleb: Move files for Beat mmu and iommu
[POWERPC] celleb: Move files for Beat hvcall interfaces
[POWERPC] celleb: Move the SCC related code for celleb
[POWERPC] celleb: Move the files for celleb base support
[POWERPC] celleb: Consolidate io-workarounds code
[POWERPC] cell: Generalize io-workarounds code
[POWERPC] Add CONFIG_PPC_PSERIES_DEBUG to enable debugging for platforms/pseries
[POWERPC] Convert from DBG() to pr_debug() in platforms/pseries/
[POWERPC] Register udbg console early on pseries LPAR
[POWERPC] Mark udbg console as CON_ANYTIME, ie. callable early in boot
[POWERPC] Set udbg_console index to 0
...
The PS3 gelic network driver depends on the wake-on-lan support
provided by the PS3 sys manager driver. Add that dependency
to the GELIC_NET Kconfig option.
Prevents these build errors:
ps3_gelic_net.c:1277: undefined reference to `.ps3_sys_manager_get_wol'
ps3_gelic_net.c:1337: undefined reference to `.ps3_sys_manager_set_wol'
CC: Masakazu Mokuno <mokuno@sm.sony.co.jp>
CC: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Convert the tc35815 driver to use the generic PHY layer in
drivers/net/phy. Also rename 'boardtype' to 'chiptype' which hould be
more appropriate.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
drivers/net/pasemi_mac.c is enabled by CONFIG_PASEMI_MAC, which depends on
PPC64 && PCI. However pasemi_mac.c uses several routines that are only
built when PPC_PASEMI is selected. This can lead to an unbuildable config:
ERROR: ".pasemi_dma_start_chan" [drivers/net/pasemi_mac.ko] undefined!
So make CONFIG_PASEMI_MAC depend on PPC_PASEMI instead of PPC64.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch adds support for the IDT rc32434 Ethernet MAC
we can find in the IDT boards and the Mikrotik RB500.
Driver references some code from the linux-mips RB500
support.
Signed-off-by: Florian Fainelli <florian.fainelli@telecomint.eu>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Philip Rischel <rischelp@idt.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
All the hardware supported by this driver is now supported
by the skge driver. The last remaining issue was support for ancient
dual port SysKonnect fiber boards, and the skge driver now does these
correctly (p.s. sk98lin was always broken on these old dual port
boards anyway).
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
| CC drivers/net/ps3_gelic_wireless.o
| /home/bigeasy/git/linux-2.6/drivers/net/ps3_gelic_wireless.c: In function 'gelic_wl_setup_netdev_ops':
| /home/bigeasy/git/linux-2.6/drivers/net/ps3_gelic_wireless.c:2660: error: 'struct net_device' has no member named 'wireless_data'
| /home/bigeasy/git/linux-2.6/drivers/net/ps3_gelic_wireless.c:2661: error: 'struct net_device' has no member named 'wireless_handlers'
| make[3]: *** [drivers/net/ps3_gelic_wireless.o] Error 1
| make[2]: *** [drivers/net] Error 2
| make[1]: *** [drivers] Error 2
| make[1]: *** Waiting for unfinished jobs....
| make: *** [sub-make] Error 2
Signed-off-by: Sebastian Siewior <sebastian@breakpoint.cc>
Acked-by: Masakazu Mokuno <mokuno@sm.sony.co.jp>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since the macvlan release I had at least 5 users asking how to configure
it since the old userspace tool doesn't work with the version in the
kernel. Add a pointer to the Kconfig help.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change the debug macros to use the compiler to elide any
unnecessary debug level, and to allow device configurable
debug control.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Masakazu Mokuno <mokuno@sm.sony.co.jp>
Acked-by: Dan Williams <dcbw@redhat.com>
Acked-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Add architecture support for the MN10300/AM33 CPUs produced by MEI to the
kernel.
This patch also adds board support for the ASB2303 with the ASB2308 daughter
board, and the ASB2305. The only processor supported is the MN103E010, which
is an AM33v2 core plus on-chip devices.
[akpm@linux-foundation.org: nuke cvs control strings]
Signed-off-by: Masakazu Urade <urade.masakazu@jp.panasonic.com>
Signed-off-by: Koichi Yasutake <yasutake.koichi@jp.panasonic.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch converts cpmac to the new Fixed PHY infrastructure, though it
doesn't fix all the problems with that driver. I didn't even bother to
test this patch to compile, because cpmac driver is broken in several ways:
1. This driver won't compile by itself because lack of its header describing
platform data;
2. It assumes that fixed PHYs should be created by the ethernet driver.
It is wrong assumption: fixed PHYs creation is platform code authority,
driver must blindly accept bus_id and phy_id platform data variables
instead.
Also, it seem that that driver doesn't have actual in-tree users, so
nothing to fix further.
The main purpose of that patch is to get rid of the following Kconfig
warning:
scripts/kconfig/conf -s arch/powerpc/Kconfig
drivers/net/Kconfig:1713:warning: 'select' used by config symbol
'CPMAC' refers to undefined symbol 'FIXED_MII_100_FDX'
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The Kconfig of igb and enc28j60 contains references to
obsolet Documentation/networking/net-modules.txt.
Signed-off-by: Johann Felix Soden <johfel@users.sourceforge.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
* git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux-2.6-for-linus: (25 commits)
virtio: balloon driver
virtio: Use PCI revision field to indicate virtio PCI ABI version
virtio: PCI device
virtio_blk: implement naming for vda-vdz,vdaa-vdzz,vdaaa-vdzzz
virtio_blk: Dont waste major numbers
virtio_blk: provide getgeo
virtio_net: parametrize the napi_weight for virtio receive queue.
virtio: free transmit skbs when notified, not on next xmit.
virtio: flush buffers on open
virtnet: remove double ether_setup
virtio: Allow virtio to be modular and used by modules
virtio: Use the sg_phys convenience function.
virtio: Put the virtio under the virtualization menu
virtio: handle interrupts after callbacks turned off
virtio: reset function
virtio: populate network rings in the probe routine, not open
virtio: Tweak virtio_net defines
virtio: Net header needs hdr_len
virtio: remove unused id field from struct virtio_blk_outhdr
virtio: clarify NO_NOTIFY flag usage
...
This patch moves virtio under the virtualization menu and changes virtio
devices to not claim to only be for lguest.
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes the no longer required dependency of IBMLANA
on MCA_LEGACY.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
