The em28xx driver have lots of different input types but
only 4 of such types are actually used. The others are bogus.
Remove them, in order to cleanup the driver.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This patch enables the tvp5150 decoder driver to be used with the media
controller framework by adding pad-level subdev operations and init the
media entity pad.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
The tvp5150 output video is interlaced so mark the format
field as alternate and reduce the height to the half.
[javier: split patch and write commit message]
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
This patch were a workaround for a regression at tvp5150, but
it causes troubles on devices with omap3+tvp5151 when working
in non-parallel bus mode.
Now that em28xx was fixed, we can get rid of that.
This reverts commit 47de9bf893.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
On em28xx driver, s_stream subdev ops was not implemented
properly. It was used only to disable stream, never enabling it.
That was the root cause of the regression when we added support
for s_stream on tvp5150 driver.
With that, we can get rid of the changes on tvp5150 side,
e. g. changeset 47de9bf893 ('[media] tvp5150: Fix breakage for serial usage').
Tested video output on em2820+tvp5150 on WinTV USB2 and
video and/or vbi output on em288x+tvp5150 on HVR 950.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
At least on Zotac CI321 ACPI provides an ioport range for the wake up part
but accessing these ioports has no effect.
Instead the ioport base address is set to another value already
(0xa20 in my case) and accessing this ioport range works.
Therefore set a new ioport base address only if the current ioport base
address is 0 (register reset default).
The need to use the existing base address instead of trying to set
an own one doesn't seem to be limited to this specific device as other
drivers like hwmon/nct6775 do it the same way.
This change was successfully tested on the mentioned device.
And the change should be generic enough to not break the driver for
other chips (however due to lack of appropriate hardware I wasn't
able to test this).
[mchehab@osg.samsung.com: Tested on Intel NUC NUC5i7RYB with BIOS
version RYBDWi35.86A.0350.2015.0812.1722]
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Tested-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Calling nvt_set_cir_iren separately is not needed as this is done
by nvt_cir_regs_init.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Selecting the logical device in the interrupt handler is not needed
as no configuration register is accessed.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Only enable the logical devices after the registers have been initialized.
The call to nvt_enable_logical_dev in nvt_resume is not needed as this is
done implicitely by nvt_cir_regs_init now.
[mchehab@osg.samsung.com: fixed multiline comment to kernel CodingStyle]
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Switch to using the recently introduced IR default timeout value
(IR_DEFAULT_TIMEOUT) and consider the value of SAMPLE_PERIOD
when calculating the limit count register value.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
At least on NVT6779D clearing the wake fifo works in learning mode only
(although this condition is not mentioned in the chip spec).
Setting the clear fifo bit has no effect in wake up mode.
Even if clearing the wake fifo should work in wake up mode on other
chips this workaround doesn't hurt.
If needed the caller of nvt_clear_cir_wake_fifo has to take care
of locking.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The two EFM ioports are accessed by drivers for other parts of the Nuvoton
Super-IO chips too. Therefore access to these ioports needs to be
protected by using request_muxed_region (like it's implemented e.g. in
hwmon/nct6775 already).
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This issue was detected by using the Coccinelle software.
Return the value from a call of the msi2500_ctrl_msg() function
without using an extra check for the variable "ret" at the end.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The variable "rc" will be set to an appropriate value from a call of
the r820t_set_tv_standard() function.
Thus let us omit the explicit initialisation at the beginning.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This issue was detected by using the Coccinelle software.
1. Let us return directly if a call of the regmap_write() function failed.
2. Delete the jump label "err" then.
3. Return zero as a constant at the end.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This issue was detected by using the Coccinelle software.
1. Let us return directly if a call of the si2165_readreg8()
function failed.
2. Reduce the scope for the local variables "ret" and "tmp" to one branch
of an if statement.
3. Delete the jump label "err" then.
4. Return the value from a call of the si2165_writereg8() function
without using an extra assignment for the variable "ret" at the end.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Matthias Schwarzott <zzam@gentoo.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The ov2659 driver performs device detection and initialization in the
following way:
- send reset command REG_SOFTWARE_RESET
- load array of predefined register's setting (~150 values)
- read device version REG_SC_CHIP_ID_H/REG_SC_CHIP_ID_L
- check version and exit if invalid.
As result, for not connected device there will be >~150 i2c transactions
executed before device version checking and exit (there are no
failures detected because ov2659 declared as I2C_CLIENT_SCCB and NACKs
are ignored in this case).
Let's fix that by checking the chip version first and start
initialization only if it's supported.
Cc: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The data type "int" was used by the variable "ret" in the
gsc_m2m_poll() function despite of the aspect that the type "unsigned int"
will usually be needed for the return value from a call of the
v4l2_m2m_poll() function.
Improve this implementation detail by addition of the type modifier then.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Add optional reset and standby gpios. The reset gpio is used to reset
the chip in power_on().
The standby gpio is not used currently. It is just unset, so the chip is
not in standby.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Passing a physical address to free_pages() is a bad idea.
config_params->fault_pxl.fpc_table_addr is set to virt_to_phys()
of __get_free_pages() return value; what we should pass to free_pages()
is its phys_to_virt(). ccdc_close() does that properly, but
ccdc_update_raw_params() doesn't.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
changeset 460b6c0831 ("tvp5150: Add s_stream subdev operation
support") broke for em28xx-based devices with uses tvp5150. On those
devices, touching the TVP5150_MISC_CTL register causes em28xx to stop
streaming.
I suspect that it uses the 27 MHz clock provided by tvp5150 to feed
em28xx. So, change the logic to do nothing on s_stream if the tvp5150 is
not set up to work with V4L2_MBUS_PARALLEL.
Tested with Hauppauge WinTV USB 2 model 42012 Rev. C186
(USB ID: 2040:4200).
Cc: Javier Martinez Canillas <javier@osg.samsung.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().
Cc: Antti Palosaari <crope@iki.fi>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
With CONFIG_V4L2=m and VIDEO_SAMSUNG_EXYNOS4_IS=y, we can select the
individual drivers as built-in code when that should not be possible:
drivers/built-in.o: In function `s5pcsis_set_fmt':
policy.c:(.text+0x13afdc): undefined reference to `v4l_bound_align_image'
drivers/built-in.o: In function `s5pcsis_probe':
policy.c:(.text+0x13b440): undefined reference to `v4l2_of_parse_endpoint'
policy.c:(.text+0x13b72c): undefined reference to `v4l2_subdev_init'
Changing VIDEO_SAMSUNG_EXYNOS4_IS to tristate means that the dependency
from CONFIG_V4L2 propates to the individual Kconfig symbols and they
can only be built as loadable modules if V4L2 or any other of the
dependencies itself is a module.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The si2165 does not support bandwidth auto-detection.
Reject the request.
Signed-off-by: Matthias Schwarzott <zzam@gentoo.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Now that this was defined at usb-id.h, update the values for
USB_PID_TERRATEC_CINERGY_S2_R1 and USB_PID_TERRATEC_CINERGY_S2_R2.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The FIFO is used for ir_raw_event records, however for some historic
reason the FIFO is used on a per byte basis. IMHO this adds unneeded
complexity. Therefore set up the FIFO for ir_raw_event records.
This also allows to define the FIFO statically as part of
ir_raw_event_ctrl instead of having to allocate the FIFO dynamically.
In addition:
- When writing into the FIFO and it's full return ENOSPC instead of
ENOMEM thus making it easier to tell between "FIFO full" and
"Dynamic memory allocation failed" when the error is propagated to
a higher level.
Also add an error message.
- When reading from the FIFO check whether it's empty.
This is not strictly needed here but kfifo_out is annotated
"must check" anyway.
Successfully tested it with the nuvoton-cir driver.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
When requesting resources use different names for the normal and
the wakeup part. This makes it easier to interpret the output
of e.g. /proc/interrupts and /proc/ioports.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
MyGica/Geniatech S2870 is very similar to the S870 but with dual tuner. The card is recognised as Geniatech STK8096-PVR.
[mchehab@osg.samsung.com: Fix some checkpatch.pl issues]
Signed-off-by: Nicolas Sugino <nsugino@3way.com.ar>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Soon my dibcom.fr/parrot.com-address won't respond anymore.
Thus I'm replacing it. And, while being at it,
let's adapt some other (old) email-addresses as well.
Signed-off-by: Patrick Boettcher <patrick.boettcher@posteo.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The Documentation/devicetree/bindings/media/i2c/tvp5150.txt DT binding doc
lists "ti,tvp5150" as the device compatible string but the driver does not
have an OF match table. Add the table to the driver so the I2C core can do
an OF style match.
Signed-off-by: Eduard Gavin <egavinc@gmail.com>
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The video decoder supports either 8-bit 4:2:2 YUV with discrete syncs
or 8-bit ITU-R BT.656 with embedded syncs output format but currently
BT.656 it's always reported. Allow to configure the format to use via
either platform data or a device tree definition.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
After power-up, the tvp5150 decoder is in a unknown state until the
RESETB pin is driven LOW which reset all the registers and restarts
the chip's internal state machine.
The init sequence has some timing constraints and the RESETB signal
can only be used if the PDN (Power-down) pin is first released.
So, the initialization sequence is as follows:
1- PDN (active-low) is driven HIGH so the chip is power-up
2- A 20 ms delay is needed before sending a RESETB (active-low) signal.
3- The RESETB pulse duration is 500 ns.
4- A 200 us delay is needed for the I2C client to be active after reset.
This patch used as a reference the logic in the IGEPv2 board file from
the ISEE 2.6.37 vendor tree.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This patch adds the .g_mbus_config subdev operation to the driver.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This patch adds the .s_stream subdev operation to the driver.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This patch adds support for the V4L2_CID_PIXEL_RATE control.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Expand the version detection code to identity the tvp5151.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Move the version detection code to a separate function and restructure
it to prepare for TVP5151 support.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The build of m32r allmodconfig fails with the error:
drivers/media/v4l2-core/videobuf2-dma-contig.c:484:2:
error: implicit declaration of function 'dma_get_cache_alignment'
The build of videobuf2-dma-contig.c depends on HAS_DMA and it is
correctly mentioned in the Kconfig but the symbol VIDEO_STI_BDISP also
selects VIDEOBUF2_DMA_CONTIG, so it is trying to compile
videobuf2-dma-contig.c even though HAS_DMA is not defined.
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Some user space use cases result in kernel hangup on the HIC_OPEN_SENSOR
command write. In case when a minimalistic application is used for setting
up the streaming, the hangups occur only occasionally. In case of GStreamer
use cases it is always the case.
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
In order to allow for automatic media device entities linking
from the level of libv4l plugin the open system call shouldn't
fail, as the libv4l plugins can begin their job not until it
succeeds.
This patch allows for leaving the pipeline not linked on
open and postpones verifying it to the moment when streamon
callback is called.
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
VIDIOC_SUBDEV_G_FMT ioctl should return TRY format previously
set with VIDIOC_SUBDEV_S_FMT. Currently it is not the case as
only ACTIVE formats are saved in the driver. Since the driver
doesn't alter hardware state in the set_fmt op anyway, the
op can save the format in both TRY and ACTIVE case.
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Ironically, 7d4020c3c4 ("[media] exynos4-is: fix some warnings when
compiling on arm64") fixed some format string bugs but introduced a
new one. buf_index is a simple int, so it should be printed with %d,
not %pad (which is correctly used for dma_addr_t).
Fixes: 7d4020c3c4 ("[media] exynos4-is: fix some warnings when compiling on arm64")
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This was found with the -RT patch enabled, but the fix should apply to
non-RT also.
Compilation error without this fix:
../drivers/media/platform/vsp1/vsp1_video.c: In function
'vsp1_pipeline_stopped':
../drivers/media/platform/vsp1/vsp1_video.c:524:2: error: expected
expression before 'do'
spin_unlock_irqrestore(&pipe->irqlock, flags);
^
Signed-off-by: Anders Roxell <anders.roxell@linaro.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The v4l2_subdev_sensor_ops structures are never modified, so declare them
as const.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The data-shift DT property speficies the number of bits to be shifted,
but the driver still interprets the value as a multiple of two bits as
used by now removed platform data support. Fix it.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The sequence number counter is incremented on each output buffer, and that
incremented value is used as the sequence number of that buffer. The input
buffer sequence numbering is based just on reading the same counter. If
the input buffer is marked done first, its sequence number ends up being
that of the output buffer - 1.
This is how the resizer works as well.
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The function can return negative value.
The problem has been detected using proposed semantic patch
scripts/coccinelle/tests/assign_signed_to_unsigned.cocci [1].
[1]: http://permalink.gmane.org/gmane.linux.kernel/2046107
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
use the vb2_buffer_state enum for assigning the state
of the vb2 buffer, along side making isp_pipeline_state
state variable local to the block.
This fixes the following sparse warning as well:
drivers/media/platform/omap3isp/ispvideo.c:497:35: warning: mixing different enum types
drivers/media/platform/omap3isp/ispvideo.c:497:35: int enum isp_pipeline_state versus
drivers/media/platform/omap3isp/ispvideo.c:497:35: int enum vb2_buffer_state
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
When the video buffer queue was stopped before the stream source was started
in omap3isp_streamon(), the buffers were not returned back to videobuf2.
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Move the starting of the sensor from the VIDIOC_STREAMON handler to the
videobuf2 queue op start_streaming. This avoids failing starting the stream
after vb2_streamon() has already finished.
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Platform drivers needs to export the OF id table and this be built
into the module or udev will not have the necessary information to
autoload the driver module when the device is registered via OF.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The Media Control framework now requires entities to be registered with
the media device before creating links so commit c7621b3044 ("[media]
v4l: vsp1: separate links creation from entities init") separated link
creation from entities init.
But unfortunately that patch introduced a regression since wrong links
were created causing a boot failure on Renesas boards.
This patch fixes the boot issue and also the media graph was compared
by Geert Uytterhoeven to make sure that the driver changes required by
the Media Control framework next generation did not affect the graph.
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Move the generic implementation to <linux/dma-mapping.h> now that all
architectures support it and remove the HAVE_DMA_ATTR Kconfig symbol now
that everyone supports them.
[valentinrothberg@gmail.com: remove leftovers in Kconfig]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Aurelien Jacquiot <a-jacquiot@ti.com>
Cc: Chris Metcalf <cmetcalf@ezchip.com>
Cc: David Howells <dhowells@redhat.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Haavard Skinnemoen <hskinnemoen@gmail.com>
Cc: Hans-Christian Egtvedt <egtvedt@samfundet.no>
Cc: Helge Deller <deller@gmx.de>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Jesper Nilsson <jesper.nilsson@axis.com>
Cc: Koichi Yasutake <yasutake.koichi@jp.panasonic.com>
Cc: Ley Foon Tan <lftan@altera.com>
Cc: Mark Salter <msalter@redhat.com>
Cc: Mikael Starvik <starvik@axis.com>
Cc: Steven Miao <realmz6@gmail.com>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: Joerg Roedel <jroedel@suse.de>
Cc: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Valentin Rothberg <valentinrothberg@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* pxafb: device-tree support
* An unsafe kernel parameter 'lockless_register_fb' for debugging problems
happening while inside the console lock
* Small miscellaneous fixes & cleanups
* omapdss: add writeback support functions
* Separation of omapfb and omapdrm (see below)
About the separation of omapfb and omapdrm, see
http://permalink.gmane.org/gmane.comp.video.dri.devel/143151 for longer story.
The short version:
omapfb and omapdrm have shared low level drivers (omapdss and panel drivers),
making further development of omapdrm difficult. After these patches omapfb and
omapdrm have their own versions of the drivers, which are more or less
direct copies for now but will diverge soon.
This also means that omapfb (everything under drivers/video/fbdev/omap2/) is
now in maintenance mode, and all new development will be done for omapdrm
(drivers/gpu/drm/omapdrm/).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJWnKg1AAoJEPo9qoy8lh71lrsP/RwwG8FDMl2tgwcsKVa/VlbF
oez/CaNeZ9Jz0qd5RbIzIS9QdbL0AZugg4twwl76UbHWT477Z3EbUmpw++78kasr
RFKDWYqMbxw3kshRDyALinGQmxPOPjNnc5mt9CYKzK4x0pJSLBmZc8qaNK3L4a5a
eLJ3h6UhQDY61D04qr+LuTCETAxNR78x+NNIG7vYa9oS0ZDDrhlDyVPw4akPDMS6
6Y5NgtRL1h2mq2hLBgTDCrwx3p7yZbnkSRKbpFnw/yddiXilND1d75JoW+0F6vKW
U8DiRKxYtHNBdry4HlpRwufT52wkmtA/2puCW5Smw8araQ7R+s+wOt/1HAYQM72g
8UCmNFMbhBpk8x8pT24ja4wyTLM9gaZqG9MWHLPEPbE6WicxSbqEAvIX9sakXLv6
dDaf1SHZ+DFpq0jOwC8Rcnx1JFeeNNDf5cJb2pZI2Zka5jayQRTdbxeZGGnpFzu1
1ZMiNQ24U+n9hgjV9QMiCW24TEBXFhFTf0Nlne3VP7qUbmvLqMUdGxGwM+b25/El
SW/peryWglxsn5EBA7XybK+RTYxbjDtD5a8SOjD2YTNqVVVFHgf7z05SfSmYO5yi
H67eDqdt0YsEGG87I8hv3eKM7FSRlYAywTC2mPfSOJ3+/G+18OU/voepcJHZ15x7
SO3e/TFTrtglJzjVzX8j
=Nrji
-----END PGP SIGNATURE-----
Merge tag 'fbdev-4.5' of git://git.kernel.org/pub/scm/linux/kernel/git/tomba/linux
Pull fbdev updates from Tomi Valkeinen:
"Summary:
- pxafb: device-tree support
- An unsafe kernel parameter 'lockless_register_fb' for debugging
problems happening while inside the console lock
- Small miscellaneous fixes & cleanups
- omapdss: add writeback support functions
- Separation of omapfb and omapdrm (see below)
About the separation of omapfb and omapdrm, see
http://permalink.gmane.org/gmane.comp.video.dri.devel/143151
for longer story. The short version:
omapfb and omapdrm have shared low level drivers (omapdss and panel
drivers), making further development of omapdrm difficult. After
these patches omapfb and omapdrm have their own versions of the
drivers, which are more or less direct copies for now but will diverge
soon.
This also means that omapfb (everything under drivers/video/fbdev/omap2/)
is now in maintenance mode, and all new development will be done for
omapdrm (drivers/gpu/drm/omapdrm/)"
* tag 'fbdev-4.5' of git://git.kernel.org/pub/scm/linux/kernel/git/tomba/linux: (49 commits)
video: fbdev: pxafb: fix out of memory error path
drm/omap: make omapdrm select OMAP2_DSS
drm/omap: move omapdss & displays under omapdrm
omapfb: move vrfb into omapfb
omapfb: take omapfb's private omapdss into use
omapfb/displays: change CONFIG_DISPLAY_* to CONFIG_FB_OMAP2_*
omapfb/dss: change CONFIG_OMAP* to CONFIG_FB_OMAP*
omapdss: remove CONFIG_OMAP2_DSS_VENC from omapdss.h
omapfb: copy omapdss & displays for omapfb
omapfb: allow compilation only if DRM_OMAP is disabled
fbdev: omap2: panel-dpi: simplify gpio setting
fbdev: omap2: panel-dpi: in .disable first disable backlight then display
OMAPDSS: DSS: fix a warning message
video: omapdss: delete unneeded of_node_put
OMAPDSS: DISPC: Remove boolean comparisons
OMAPDSS: DSI: cleanup DSI_IRQ_ERROR_MASK define
OMAPDSS: remove extra out == NULL checks
OMAPDSS: change internal dispc functions to static
OMAPDSS: make a two dss feat funcs internal to omapdss
OMAPDSS: remove extra EXPORT_SYMBOLs
...
Infrastructural changes:
- In struct gpio_chip, rename the .dev node to .parent to better reflect
the fact that this is not the GPIO struct device abstraction. We will
add that soon so this would be totallt confusing.
- It was noted that the driver .get_value() callbacks was
sometimes reporting negative -ERR values to the gpiolib core, expecting
them to be propagated to consumer gpiod_get_value() and gpio_get_value()
calls. This was not happening, so as there was a mess of drivers
returning negative errors and some returning "anything else than zero"
to indicate that a line was active. As some would have bit 31 set to
indicate "line active" it clashed with negative error codes. This is
fixed by the largeish series clamping values in all drivers with
!!value to [0,1] and then augmenting the code to propagate error codes
to consumers. (Includes some ACKed patches in other subsystems.)
- Add a void *data pointer to struct gpio_chip. The container_of() design
pattern is indeed very nice, but we want to reform the struct gpio_chip
to be a non-volative, stateless business, and keep states internal to
the gpiolib to be able to hold on to the state when adding a proper
userspace ABI (character device) further down the road. To achieve this,
drivers need a handle at the internal state that is not dependent on
their struct gpio_chip() so we add gpiochip_add_data() and
gpiochip_get_data() following the pattern of many other subsystems.
All the "use gpiochip data pointer" patches transforms drivers to this
scheme.
- The Generic GPIO chip header has been merged into the general
<linux/gpio/driver.h> header, and the custom header for that removed.
Instead of having a separate mm_gpio_chip struct for these generic
drivers, merge that into struct gpio_chip, simplifying the code and
removing the need for separate and confusing includes.
Misc improvements:
- Stabilize the way GPIOs are looked up from the ACPI legacy
specification.
- Incremental driver features for PXA, PCA953X, Lantiq (patches from the
OpenWRT community), RCAR, Zynq, PL061, 104-idi-48
New drivers:
- Add a GPIO chip to the ALSA SoC AC97 driver.
- Add a new Broadcom NSP SoC driver (this lands in the pinctrl dir, but
the branch is merged here too to account for infrastructural changes).
- The sx150x driver now supports the sx1502.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=63rR
-----END PGP SIGNATURE-----
Merge tag 'gpio-v4.5-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO updates from Linus Walleij:
"Here is the bulk of GPIO changes for v4.5.
Notably there are big refactorings mostly by myself, aimed at getting
the gpio_chip into a shape that makes me believe I can proceed to
preserve state for a proper userspace ABI (character device) that has
already been proposed once, but resulted in the feedback that I need
to go back and restructure stuff. So I've been restructuring stuff.
On the way I ran into brokenness (return code from the get_value()
callback) and had to fix it. Also, refactored generic GPIO to be
simpler.
Some of that is still waiting to trickle down from the subsystems all
over the kernel that provide random gpio_chips, I've touched every
single GPIO driver in the kernel now, oh man I didn't know I was
responsible for so much...
Apart from that we're churning along as usual.
I took some effort to test and retest so it should merge nicely and we
shook out a couple of bugs in -next.
Infrastructural changes:
- In struct gpio_chip, rename the .dev node to .parent to better
reflect the fact that this is not the GPIO struct device
abstraction. We will add that soon so this would be totallt
confusing.
- It was noted that the driver .get_value() callbacks was sometimes
reporting negative -ERR values to the gpiolib core, expecting them
to be propagated to consumer gpiod_get_value() and gpio_get_value()
calls. This was not happening, so as there was a mess of drivers
returning negative errors and some returning "anything else than
zero" to indicate that a line was active. As some would have bit
31 set to indicate "line active" it clashed with negative error
codes. This is fixed by the largeish series clamping values in all
drivers with !!value to [0,1] and then augmenting the code to
propagate error codes to consumers. (Includes some ACKed patches
in other subsystems.)
- Add a void *data pointer to struct gpio_chip. The container_of()
design pattern is indeed very nice, but we want to reform the
struct gpio_chip to be a non-volative, stateless business, and keep
states internal to the gpiolib to be able to hold on to the state
when adding a proper userspace ABI (character device) further down
the road. To achieve this, drivers need a handle at the internal
state that is not dependent on their struct gpio_chip() so we add
gpiochip_add_data() and gpiochip_get_data() following the pattern
of many other subsystems. All the "use gpiochip data pointer"
patches transforms drivers to this scheme.
- The Generic GPIO chip header has been merged into the general
<linux/gpio/driver.h> header, and the custom header for that
removed. Instead of having a separate mm_gpio_chip struct for
these generic drivers, merge that into struct gpio_chip,
simplifying the code and removing the need for separate and
confusing includes.
Misc improvements:
- Stabilize the way GPIOs are looked up from the ACPI legacy
specification.
- Incremental driver features for PXA, PCA953X, Lantiq (patches from
the OpenWRT community), RCAR, Zynq, PL061, 104-idi-48
New drivers:
- Add a GPIO chip to the ALSA SoC AC97 driver.
- Add a new Broadcom NSP SoC driver (this lands in the pinctrl dir,
but the branch is merged here too to account for infrastructural
changes).
- The sx150x driver now supports the sx1502"
* tag 'gpio-v4.5-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (220 commits)
gpio: generic: make bgpio_pdata always visible
gpiolib: fix chip order in gpio list
gpio: mpc8xxx: Do not use gpiochip_get_data() in mpc8xxx_gpio_save_regs()
gpio: mm-lantiq: Do not use gpiochip_get_data() in ltq_mm_save_regs()
gpio: brcmstb: Allow building driver for BMIPS_GENERIC
gpio: brcmstb: Set endian flags for big-endian MIPS
gpio: moxart: fix build regression
gpio: xilinx: Do not use gpiochip_get_data() in xgpio_save_regs()
leds: pca9532: use gpiochip data pointer
leds: tca6507: use gpiochip data pointer
hid: cp2112: use gpiochip data pointer
bcma: gpio: use gpiochip data pointer
avr32: gpio: use gpiochip data pointer
video: fbdev: via: use gpiochip data pointer
gpio: pch: Optimize pch_gpio_get()
Revert "pinctrl: lantiq: Implement gpio_chip.to_irq"
pinctrl: nsp-gpio: use gpiochip data pointer
pinctrl: vt8500-wmt: use gpiochip data pointer
pinctrl: exynos5440: use gpiochip data pointer
pinctrl: at91-pio4: use gpiochip data pointer
...
Pull trivial tree updates from Jiri Kosina.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial:
floppy: make local variable non-static
exynos: fixes an incorrect header guard
dt-bindings: fixes some incorrect header guards
cpufreq-dt: correct dead link in documentation
cpufreq: ARM big LITTLE: correct dead link in documentation
treewide: Fix typos in printk
Documentation: filesystem: Fix typo in fs/eventfd.c
fs/super.c: use && instead of & for warn_on condition
Documentation: fix sysfs-ptp
lib: scatterlist: fix Kconfig description
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=6J4t
-----END PGP SIGNATURE-----
Merge tag 'media/v4.5-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull second batch of media updates from Mauro Carvalho Chehab:
"This is the second part of the media patches. It contains the media
controller next generation patches, with is the result of one year of
discussions and development. It also contains patches to enable media
controller support at the DVB subsystem.
The goal is to improve the media controller to allow proper support
for other types of Video4Linux devices (radio and TV ones) and to
extend the media controller functionality to allow it to be used by
other subsystems like DVB, ALSA and IIO.
In order to use the new functionality, a new ioctl is needed
(MEDIA_IOC_G_TOPOLOGY). As we're still discussing how to pack the
struct fields of this ioctl in order to avoid compat32 issues, I
decided to add a patch at the end of this series commenting out the
new ioctl, in order to postpone the addition of the new ioctl to the
next Kernel version (4.6).
With that, no userspace visible changes should happen at the media
controller API, as the existing ioctls are untouched. Yet, it helps
DVB, ALSA and IIO developers to develop and test the patches adding
media controller support there, as the core will contain all required
internal changes to allow adding support for devices that belong to
those subsystems"
* tag 'media/v4.5-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (177 commits)
[media] Postpone the addition of MEDIA_IOC_G_TOPOLOGY
[media] mxl111sf: Add a tuner entity
[media] dvbdev: create links on devices with multiple frontends
[media] media-entitiy: add a function to create multiple links
[media] dvb-usb-v2: postpone removal of media_device
[media] dvbdev: Add RF connector if needed
[media] dvbdev: remove two dead functions if !CONFIG_MEDIA_CONTROLLER_DVB
[media] call media_device_init() before registering the V4L2 device
[media] uapi/media.h: Use u32 for the number of graph objects
[media] media-entity: don't sleep at media_device_register_entity()
[media] media-entity: increase max number of PADs
[media] media-entity.h: document the remaining functions
[media] media-device.h: use just one u32 counter for object ID
[media] media-entity.h fix documentation for several parameters
[media] DocBook: document media_entity_graph_walk_cleanup()
[media] move documentation to the header files
[media] media: Move MEDIA_ENTITY_MAX_PADS from media-entity.h to media-entity.c
[media] media: Remove pre-allocated entity enumeration bitmap
[media] staging: v4l: davinci_vpbe: Use the new media graph walk interface
[media] staging: v4l: omap4iss: Use the new media graph walk interface
...
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=PA5/
-----END PGP SIGNATURE-----
Merge tag 'media/v4.5-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media updates from Mauro Carvalho Chehab:
"The part of patches for Kernel 4.5. There's nothing really big here:
- driver-specific headers for media devices were moved to separate
directories, in order to make clear what headers belong to the core
kABI and require documentation
- Platform data for media drivers were moved from include/media to
include/linux/platform_data/media
- add a driver for cs3308 8-channel volume control, used on some
high-end capture boards
- lirc.h kAPI header were added at include/uapi/linux
- Driver cleanups, new board additions and improvements"
* tag 'media/v4.5-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (204 commits)
[media] rc: sunxi-cir: Initialize the spinlock properly
[media] rtl2832: do not filter out slave TS null packets
[media] rtl2832: print reg number on error case
[media] rtl28xxu: return demod reg page from driver cache
[media] coda: enable MPEG-2 ES decoding
[media] coda: don't start streaming without queued buffers
[media] coda: hook up vidioc_prepare_buf
[media] coda: relax coda_jpeg_check_buffer for trailing bytes
[media] coda: make to_coda_video_device static
[media] s5p-mfc: remove volatile attribute from MFC register addresses
[media] s5p-mfc: merge together s5p_mfc_hw_call and s5p_mfc_hw_call_void
[media] s5p-mfc: use spinlock to protect MFC context
[media] s5p-mfc: remove unnecessary callbacks
[media] s5p-mfc: make queue cleanup code common
[media] s5p-mfc: use one implementation of s5p_mfc_get_new_ctx
[media] s5p-mfc: constify s5p_mfc_codec_ops structures
[media] au8522: Avoid memory leak for device config data
[media] ir-lirc-codec.c: don't leak lirc->drv-rbuf
[media] uvcvideo: small cleanup in uvc_video_clock_update()
[media] uvcvideo: Fix reading the current exposure value of UVC
...
There are a few discussions left with regards to this ioctl:
1) the name of the new structs will contain _v2_ on it?
2) what's the best alternative to avoid compat32 issues?
Due to that, let's postpone the addition of this new ioctl to
the next Kernel version, to give people more time to discuss it.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
While mxl111sf may have multiple frontends, it has just one
tuner. Reflect that on the media graph.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Devices like mxl111sf-based WinTV Aero-m have multiple
frontends, all linked on the same demod. Currently, the
dvb_create_graph() function is not smart enough to create
multiple links. Fix it.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Sometimes, it is desired to create 1:n and n:1 or even
n:n links between different entities with the same
function.
This is actually needed to support DVB devices that
have multiple frontends. While we could do a function
like that internally at the DVB core, such function is
generic enough to be at media-entity, and it could be
useful on some other places.
So, add such function.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
We should not remove the media_device until its last usage,
or we may have use after free troubles.
So, move the per-adapter media_device removal to happen at
the end of the adapter removal code.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Several pure digital TV devices have a frontend with the tuner
integrated on it. Add the RF connector when dvb_create_media_graph()
is called on such devices.
Tested with siano and dvb_usb_mxl111sf drivers.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Those functions are used only if CONFIG_MEDIA_CONTROLLER_DVB.
Without that, if !CONFIG_MEDIA_CONTROLLER_DVB, it would produce
two warnings:
drivers/media/dvb-core/dvbdev.c:219:12: warning: 'dvb_create_tsout_entity' defined but not used [-Wunused-function]
static int dvb_create_tsout_entity(struct dvb_device *dvbdev,
^
drivers/media/dvb-core/dvbdev.c:264:12: warning: 'dvb_create_media_entity' defined but not used [-Wunused-function]
static int dvb_create_media_entity(struct dvb_device *dvbdev,
^
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Currently, v4l2_device_register() doesn't use the media_device
struct. So, calling media_device_init() could be called either
before or after v4l2_device_register().
Yet, it is a good practice to initialize everything before calling
the register functions. Also, the other drivers call
media_device_init() before registering the V4L2 device.
So, move the call for media_device_init() to happen earlier on
exynos4-is and s3c-camif.
This is just a cleanup patch.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The DVB drivers may have 257 PADs. Get the next power of two
that would accomodate that amount.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Instead of using one u32 counter per type for object IDs, use
just one counter. With such change, it makes sense to simplify
the debug logs too.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Some exported functions were still documented at the .c file,
instead of documenting at the .h one.
Move the documentation to the right place, as we only use headers
at media device-drivers.xml DocBook.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This isn't really a part of any interface drivers are expected to use. In
order to keep drivers from using it, hide it in media-entity.c. This was
always an arbitrary number and should be removed in the long run.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The bitmaps for entity enumerations used to be statically allocated. Now
that the drivers have been converted to use the new interface which
explicitly initialises the enum objects, drop the pre-allocated bitmaps.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Instead of using a bitmap directly in a driver, use the new media entity
enumeration interface to perform the same.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Instead of using a bitmap directly in a driver, use the new media entity
enumeration interface to perform the same.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Initialise a given graph walk object once, and then keep using it whilst
the same pipeline is running. Once the pipeline is stopped, release the
graph walk object.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This will also mean that the necessary graph related data structures will
be allocated dynamically, removing the need for maximum ID checks.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The media graph walk requires initialisation and cleanup soon. Update the
users to perform the soon necessary API calls.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The media graph walk requires initialisation and cleanup soon. Update the
users to perform the soon necessary API calls.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Cc: Hyun Kwon <hyun.kwon@xilinx.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The media graph walk requires initialisation and cleanup soon. Update the
users to perform the soon necessary API calls.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Cc: Javier Martinez Canillas <javier@osg.samsung.com>
Cc: Kamil Debski <k.debski@samsung.com>
Cc: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The media graph walk requires initialisation and cleanup soon. Update the
users to perform the soon necessary API calls.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The media graph walk requires initialisation and cleanup soon. Update the
users to perform the soon necessary API calls.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Add media_entity_graph_walk_init() and media_entity_graph_walk_cleanup()
functions in order to dynamically allocate memory for the graph. This is
not done in media_entity_graph_walk_start() as there are situations where
e.g. correct error handling, that itself may not fail, requires successful
graph walk.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The struct media_entity_graph was allocated in the stack, limiting the
number of entities that could be reasonably allocated. Instead, move the
struct to struct media_pipeline which is typically allocated using
kmalloc() instead.
The intent is to keep the enumeration around for later use for the
duration of the streaming. As streaming is eventually stopped, an
unfortunate memory allocation failure would prevent stopping the
streaming. As no memory will need to be allocated, the problem is avoided
altogether.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This is useful in e.g. knowing whether certain operations have already
been performed for an entity. The users include the framework itself (for
graph walking) and a number of drivers.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The internal index can be used internally by the framework in order to keep
track of entities for a purpose or another. The internal index is constant
while it's registered to a media device, but the same index may be re-used
once the entity having that index is unregistered.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
We need to set "err = -ENOMEM" here.
Fixes: 38b11f19667a ('[media] v4l2-core: create MC interfaces for devnodes')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The copy_to/from_user() functions return the number of bytes *not*
copied. They don't return error codes.
Fixes: 4f6b3f363475 ('media] media-device: add support for MEDIA_IOC_G_TOPOLOGY ioctl')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The G_TOPOLOGY ioctl is used to get a graph topology and since in the
future a graph can be dynamically updated, there is a way to know the
topology version so userspace can be aware that the graph has changed.
The version 0 is reserved to indicate that the graph is static (i.e no
graphs updates since the media device was registered).
So, now that the media device initialization and registration has been
split and the media device node is not exposed to user-space until all
the entities have been registered and links created, it is safe to set
a topology version 0 in media_device_register().
Suggested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Suggested-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Registering a V4L2 sub-device includes, among other things, registering
the related media entity and calling the sub-device's registered op. Since
patch "media: convert links from array to list", creating a link between
two pads requires registering the entity first. If the registered() op
involves link creation, the link list head will not be initialised before
it is used.
Resolve this by first registering the entity, then calling its
registered() op.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
There are now two new warnings:
drivers/media/usb/dvb-usb-v2/dvb_usb_core.c: In function 'dvb_usbv2_media_device_register':
drivers/media/usb/dvb-usb-v2/dvb_usb_core.c:433:2: warning: ignoring return value of '__media_device_register', declared with attribute warn_unused_result [-Wunused-result]
media_device_register(adap->dvb_adap.mdev);
^
drivers/media/usb/dvb-usb/dvb-usb-dvb.c: In function 'dvb_usb_media_device_register':
drivers/media/usb/dvb-usb/dvb-usb-dvb.c:128:2: warning: ignoring return value of '__media_device_register', declared with attribute warn_unused_result [-Wunused-result]
media_device_register(adap->dvb_adap.mdev);
^
Those are because the drivers are not properly checking if the
media device init and register were succeeded.
Fix it.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The media device node is registered and so made visible to user-space
before entities are registered and links created which means that the
media graph obtained by user-space could be only partially enumerated
if that happens too early before all the graph has been created.
To avoid this race condition, split the media init and registration
in separate functions and only register the media device node when
all the pending subdevices have been registered, either explicitly
by the driver or asynchronously using v4l2_async_register_subdev().
The media_device_register() had a check for drivers not filling dev
and model fields but all drivers in mainline set them and not doing
it will be a driver bug so change the function return to void and
add a BUG_ON() for dev being NULL instead.
Also, add a media_device_cleanup() function that will destroy the
graph_mutex that is initialized in media_device_init().
[mchehab@osg.samsung.com: Fix compilation if !CONFIG_MEDIA_CONTROLLER
and remove two warnings added by this changeset]
Suggested-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
If media_device_unregister() is called by two different
drivers, a race condition may happen, as the check if the
device is not registered is not protected.
Move the spin_lock() to happen earlier in the function, in order
to prevent such race condition.
Reported-by: Shuah Khan <shuahkh@osg.samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
media entity register and unregister functions are called by media
device register/unregister. Move them to occur earlier, as we'll need
an unlocked version of media_device_entity_unregister() and we don't
want to add a function prototype without needing it.
No functional changes.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Most media functions that unregister, check if the corresponding register
function succeed before. So these functions can safely be called even if a
registration was never made or the component as already been unregistered.
Add the same check to media_device_unregister() function for consistency.
This will also allow to split the media_device_register() function in an
initialization and registration functions without the need to change the
generic cleanup functions and error code paths for all the media drivers.
Suggested-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
As pointed by Dan, the commit f8fd4c61b5ae ("[media] media-entity:
protect object creation/removal using spin lock")' leads to the
following static checker warning:
drivers/media/media-entity.c:781 media_remove_intf_link()
error: dereferencing freed memory 'link'
drivers/media/media-entity.c
777 void media_remove_intf_link(struct media_link *link)
778 {
779 spin_lock(&link->graph_obj.mdev->lock);
780 __media_remove_intf_link(link);
781 spin_unlock(&link->graph_obj.mdev->lock);
In practice, I didn't see any troubles even with KASAN enabled. I guess
gcc optimizer internally cached the mdev reference, instead of getting
it twice. Yet, it is a very bad idea to rely on such optimization. So,
let's fix the code.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Changeset f8fd4c61b5ae ("[media] media-entity: protect object
creation/removal using spin lock") changed the object creation/removal
protection to spin lock, as this is what's used on media-device,
keeping the mutex reserved for graph traversal routines. However, it
also changed the link setup, by mistake.
This could cause troubles, as the link setup can affect the graph
traversal, and this is likely the reason for a mutex there.
So, revert media_entity_setup_link() to use mutex.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
As we're using the headers file only for documentation, move the
two kernel-doc macros to the header, and fix it to avoid
warnings.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
If a different entity->pipe in a pipeline was encountered, a warning was
issued but the execution continued as if nothing had happened. Return an
error instead right there.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The Media Controller next gen patchset added several new fields
to be used with it. Document them.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Instead of flagging an interface link as MEDIA_LNK_FL_INTERFACE_LINK
only when returning to userspace, do it at link creation time.
That would allow using such flag internally, and cleans up a
little bit the code for G_TOPOLOGY ioctl.
[mchehab@osg.samsung.com: folded with a fixup from Dan Carpenter,
replacing & by &&]
Suggested-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Commit 86ee417578a2 ("[media] media: convert links from array to list")
had many changes that were automated using coccinelle but the semantic
patch was not smart enough to rely on operators precedence and avoid
using unnecessary enclosing parenthesis.
This patch removes them since are not needed.
Suggested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The uvc_mc_register_entities() function iterated over the entities three
times to initialize the entities, register the subdev for the ones whose
type was UVC_TT_STREAMING and to create the entities links.
But this can be simplied by merging the init and registration logic in a
single loop.
Suggested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The function uvc_mc_create_pads_links() creates entities links but the
"pads" prefix is redundant since the driver doesn't handle any other
kind of link, so it can be removed.
Suggested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The for loop in the vsp1_create_entities() function that create the links,
checks the entity type and call the proper link creation function but then
it uses continue to force the next iteration of the loop to take place and
skipping code in between that creates links for different entities types.
It is more readable and easier to understand if the if else constructs is
used instead of the continue statement.
Suggested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The functions that create entities links are called *_create_pads_links()
but the "pads" prefix is redundant since the driver doesn't handle any
other kind of link so it can be removed.
Suggested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The isp_subdev_notifier_complete() complete callback defines a struct
v4l2_device *v4l2_dev to avoid needing two level of indirections to
access the V4L2 subdevs but the var is not always used when possible
as when calling v4l2_device_register_subdev_nodes().
So change that to consistently use the defined v4l2_dev pointer var.
Suggested-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Commit bc36b30fe06b ("[media] omap3isp: separate links creation from
entities init") moved the link creation logic from the entities init
functions and so removed the error_link labels from the error paths.
But after that, some functions have a single error label so it makes
more sense to rename the label to just "error" in thi case.
Suggested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The function that creates the links between ISP internal and external
entities is called isp_create_pads_links() but the "pads" prefix is
redundant since the driver doesn't handle any other kind of link so
it can just be removed.
While being there, fix the function's kernel-doc since is not using
a proper format.
Suggested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The entities to video nodes links were created on separate functions for
each ISP module but since the only thing that these functions do is to
call media_create_pad_link(), there's no need for that indirection level
and all link creation logic can be just inlined in the caller function.
Also, since the only possible failure for the link creation is a memory
allocation, there is no need for error messages since the core already
reports a very verbose message in that case.
Suggested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
By using u64 integers and pointers, we can get rid of compat32
logic. So, let's do it!
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Suggested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The pad index is unsigned. Replace the occurences of it where
pertinent.
Suggested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Several additional functions are described at media-entity.c.
Moving them to the header file, to make the code cleaner and
to have all such macros at the same place.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Those media_obj_* functions are actually creating/destroying
media graph objects. So, rename them to better represent
what they're actually doing.
No functional changes.
This was created via this small shell script:
for i in $(git grep -l media_gobj_init); do sed s,media_gobj_init,media_gobj_create,g <$i >a && mv a $i; done
for i in $(git grep -l media_gobj_remove); do sed s,media_gobj_remove,media_gobj_destroy,g <$i >a && mv a $i; done
Suggested-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
> > > + if (rlink != link->reverse) {
> > > + r++;
> >
> > The variable is incremented here but otherwise never used, you can remove it.
Suggested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Move this function to happen earlier, in order to avoid
a uneeded forward declaration.
Suggested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This function was used in the past to free the links
that were allocated by the media controller core.
However, this is not needed anymore. We should likely
get rid of the funcion on some function, but, for now,
let's just convert into an inlined function and let the
compiler to get rid of it.
Suggested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Both revision and group_id fields were never used and were always
initialized to zero. Remove them.
Suggested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
With the MC next gen rework, what's left for media_entity_init()
is to just initialize the PADs. However, certain devices, like
a FLASH led/light doesn't have any input or output PAD.
So, there's no reason why calling media_entity_init() would be
mandatory. Also, despite its name, what this function actually
does is to initialize the PADs data. So, rename it to
media_entity_pads_init() in order to reflect that.
The media entity actual init happens during entity register,
at media_device_register_entity(). We should move init of
num_links and num_backlinks to it.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The __media_device_enum_links() copies links definitions from
Kernelspace to userspace. It has to work with 3 structs that
handle with links. Better name them to:
link: Kernelspace internal link representation, of the
type media_link;
klink_desc: struct media_link_desc pointer to the
kernel memory where the data will be filled;
ulink_desc: struct media_link_desc pointer to the
memory where the data will be copied to
userspace.
Suggested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
It is better to keep the headers in alphabetic order.
Suggested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
If an entity is registered with a media device before is initialized
with media_device_register_entity(), the number of pads won't be set
so media_device_register_entity() won't create pad objects and add
it to the media device pads list.
Do this at entity initialization time if the entity was registered
before so the graph is complete and correct regardless of the order
in which the entities are initialized and registered.
Suggested-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The entity->num_pads are defined as u16. So, better to use an
unsigned int, as this prevents additional warnings when W=2
(or W=1 on some architectures).
The "i" counter at __media_device_get_topology() is also a
monotonic counter that should never be below zero. So,
make it unsigned too.
Suggested-by: Sakari Ailus <sakari.ailus@iki.fi>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
We should not be creating device nodes at IRQ contexts. So,
the only flags we'll be using will be GFP_KERNEL. Let's
remove the gfp_flags, in order to make the interface simpler.
If we ever need it, it would be easy to revert those changes.
While here, remove an extra blank line.
Suggested-by: Sakari Ailus <sakari.ailus@iki.fi>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Indirect links are those whose interface indirectly controls
other functions.
There are two interfaces that have indirect controls at the DVB
side:
- the network interface, which also controls the demux;
- the DVR interface which also controls the demux.
One could argue that the frontend control to the tuner is indirect.
Well, that's debatable. There's no way to create subdev interfaces
for tuner and demod, as those devices are tightly coupled. So, it
was decided that just one interface is the best to control both
entities, and there's no plan (or easy way) to decouple both. So,
the DVB frontend interface should link to both entities.
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Cleanup the code a little bit by moving the routine that creates
links between DVR and demux to the I/O entitis into a separate
function.
While here, fix the code to use strncmp() instead of strcmp().
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Now that entities have a main function, expose it via
MEDIA_IOC_G_TOPOLOGY ioctl.
Please notice that some entities may have secundary functions.
Such use case will be addressed later, when we add support for the
Media Controller properties.
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Entities should have one or more functions. Calling it as a
type proofed to not be correct, as an entity could eventually
have more than one type.
So, rename the field as function.
Please notice that this patch doesn't extend support for
multiple function entities. Such change will happen when
we have real case drivers using it.
No functional changes.
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
If the graph creation fails, don't register the device.
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
If the graph creation fails, don't register the device.
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
If media controller is enabled and mdev is filled, it should
ensure that the media graph will be properly initialized.
Enforce that.
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Interface links are normally enabled, meaning that the interfaces are
bound to the entities. So, any ioctl send to the interface are reflected
at the entities managed by the interface.
However, when a device is used, other interfaces for the same hardware
could be decoupled from the entities linked to them, because the
hardware may have some parts busy.
That's for example, what happens when an hybrid TV device is in use.
If it is streaming analog TV or capturing signals from S-Video/Composite
connectors, typically the digital part of the hardware can't be used and
vice-versa.
This is generally due to some internal hardware or firmware limitation,
that it is not easily mapped via data pipelines.
What the Kernel drivers do internally is that they decouple the hardware
from the interface. So, all changes, if allowed, are done only at some
interface cache, but not physically changed at the hardware.
The usage is similar to the usage of the MEDIA_LNK_FL_ENABLED on data
links. So, let's use the same flag to indicate if either the interface
to entity link is bound/enabled or not.
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Due to the graph traversal algorithm currently in usage, we
need a copy of all data links. Those backlinks should not be
send to userspace, as otherwise, all links there will be
duplicated.
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Depending on the input, an au0828 may have a different
number of connectors. add entities to represent them.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
V4L2 device (and subdevice) nodes should create an interface, if the
Media Controller support is enabled.
Please notice that radio devices should not create an entity, as radio
input/output is either via wires or via ALSA.
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Right now, if something gets wrong at dvb_create_media_entity()
or at dvb_create_media_graph(), the device will still be
registered.
Change the logic to properly handle it and free all media graph
objects if something goes wrong at dvb_register_device().
Also, change the logic at dvb_create_media_graph() to return
an error code if something goes wrong. It is up to the
caller to implement the right logic and to call
dvb_unregister_device() to unregister the already-created
objects.
While here, add a missing logic to unregister the created
interfaces.
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The logic is testing if num_links==0 at the wrong place. Due to
that, a backlink may be kept without removal, causing KASAN
to complain about usage after free during either entity or
link removal.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The media_entity_cleanup() function only cleans up the entity links list
but this operation is already made in media_device_unregister_entity().
In most cases this should be harmless (besides having duplicated code)
since the links list would be empty so the iteration would not happen
but the links list is initialized in media_device_register_entity() so
if a driver fails to register an entity with a media device and clean up
the entity in the error path, a NULL deference pointer error will happen.
So don't try to empty the links list in media_entity_cleanup() since
is either done already or haven't been initialized yet.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
The DVB core needs to unregister the media device. So, we
can't call au0828_unregister_media_device() before calling
au0828_dvb_unregister(), otherwise the DVB MC free code
(that will be implemented on the next patch) will fail.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Interface links are normally enabled, meaning that the interfaces are
bound to the entities. So, any ioctl sent to the interface are reflected
at the entities managed by the interface.
However, when a device is in use, other interfaces for the same hardware
could be decoupled from the entities linked to them, because the
hardware may have some parts busy.
That's for example, what happens when an hybrid TV device is in use.
If it is streaming analog TV or capturing signals from S-Video/Composite
connectors, typically the digital part of the hardware can't be used and
vice-versa.
This is generally due to some internal hardware or firmware limitation,
that it is not easily mapped via data pipelines.
What the Kernel drivers do internally is that they decouple the hardware
from the interface. So, all changes, if allowed, are done only at some
interface cache, but not physically changed at the hardware.
The usage is similar to the usage of the MEDIA_LNK_FL_ENABLED on data
links. So, let's use the same flag to indicate if either the interface
to entity link is bound/enabled or not.
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Tuners actually have at least one connector on its input.
Add a PAD to connect it.
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Some parts of the media controller are using mutexes while
others are using spin locks in order to protect creation
and removal of elements in the graph. That's wrong!
Also, the V4L2 core can remove graph elements on non-interactive
context:
BUG: sleeping function called from invalid context at include/linux/sched.h:2776
Fix it by always using spin locks for graph element addition/removal,
just like entity creation/removal is protected at media-device.c
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Just like what's done with entities, when the media controller is
unregistered, release any interface and interface links that
might still be there.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Interface links connected to an entity should be removed
before the entity itself can be removed.
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Add functions to explicitly unregister all entity links.
This function is called automatically when an entity
link is destroyed.
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Add support for the new MEDIA_IOC_G_TOPOLOGY ioctl, according
with the RFC for the MC next generation.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Every time a graph object is added or removed, the version
of the topology changes. That's a requirement for the new
MEDIA_IOC_G_TOPOLOGY, in order to allow userspace to know
that the topology has changed after a previous call to it.
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The MC next gen API sends objects to userspace grouped by
their types.
In the case of pads and links, in order to improve performance
and have a simpler code, the best is to store them also on
separate linked lists at MC.
If we don't do that, we would need this kind of interaction
to send data to userspace (code is in structured english):
for each entity:
for each pad:
store pads
for each entity:
for each link:
store link
for each interface:
for each link:
store link
With would require one nested loop for pads and two nested
loops for links. By using separate linked lists for them,
just one loop would be enough.
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Let's control the topology changes inside the graph_object. So, move the
addition and removal of interfaces/entities from the mdev lists to
media_gobj_init() and media_gobj_remove().
The main reason is that mdev should have lists for all object types, as
the new MC api will require to store objects in separate places.
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Just like we do with entities, use a similar macro for the
interfaces loop.
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Sometimes, it is important to see if the created pad is
sink or source. Add info to track that.
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The Media Controller New Generation redefines the types for both
interfaces and entities to be used on DVB. Make the needed
changes at the DVB core for all interfaces, entities and
data and interface links to appear in the graph.
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Instead of abusing MEDIA_ENT_T_V4L2_SUBDEV, initialize
new subdev entities as MEDIA_ENT_T_UNKNOWN.
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The driver creates two subdevs, one for the image sensor pixel array
(and the related readout logic) and one for an ISP.
The first subdev already uses the MEDIA_ENT_T_V4L2_SUBDEV_SENSOR type,
but the second subdev isn't a sensor pixel array.
So, rename the second subdev as MEDIA_ENT_T_V4L2_SUBDEV_UNKNOWN.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This sensor driver is abusing MEDIA_ENT_T_V4L2_SUBDEV, creating
some subdevs with a non-existing type.
As this is a sensor driver, one of the entries is
MEDIA_ENT_T_CAM_SENSOR. The other one will be using
MEDIA_ENT_T_V4L2_SUBDEV_UNKNOWN, because the subdev is not
any of the already existing types.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
On omap3/omap4/davinci drivers, MEDIA_ENT_T_V4L2_SUBDEV macro is
abused in order to "simplify" the pad checks.
Basically, it does a logical or of this macro, in order to check
for a local index and if the entity is either a subdev or not.
As we'll get rid of MEDIA_ENT_T_V4L2_SUBDEV macro, replace it by
2 << 16 where it occurs, and add a note saying that the code
there is actually a hack.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Instead of relying on media subtype, use the new macros to detect
if an entity is a subdev or an A/V DMA entity.
Please note that most drivers assume that there's just AV_DMA or
V4L2 subdevs. This is not true anymore, as we've added MC support
for DVB, and there are plans to add support for ALSA and FB/DRM
too.
Ok, on the current pipelines supported by those drivers, just V4L
stuff are there, but, assuming that some day a pipeline that also
works with other subsystems will ever added, it is better to add
explicit checks for the AV_DMA stuff.
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Now that interfaces and entities are distinct, it makes no sense
of keeping something named as MEDIA_ENT_T_DEVNODE.
This change was done with this script:
for i in $(git grep -l MEDIA_ENT_T|grep -v uapi/linux/media.h); do sed s,MEDIA_ENT_T_DEVNODE_V4L,MEDIA_ENT_T_V4L2_VIDEO, <$i >a && mv a $i; done
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Now that interfaces got created, we need to fix the entity
namespace.
So, let's create a consistent new namespace and add backward
compatibility macros to keep the old namespace preserved.
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Some interfaces indirectly control multiple entities.
Add support for those.
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The media device should list the interface objects, so add a linked list
for those interfaces in struct media_device.
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Now that the infrastruct for that is set, add support for
interfaces.
Please notice that we're missing two links:
DVB FE intf -> tuner
DVB demux intf -> dvr
Those should be added latter, after having the entire graph
set. With the current infrastructure, those should be added
at dvb_create_media_graph(), but it would also require some
extra core changes, to allow the function to enumerate the
interfaces.
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
As we'll be adding other interface types in the future, put the
common interface create code on a separate function.
Suggested-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Now that we have a new graph object called "interfaces", we
need to be able to link them to the entities.
Add a linked list to the interfaces to allow them to be
linked to the entities.
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Remove entity name from the link as this exists only if the object
type is PAD on both link ends.
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The media_entity_add_link() function takes an entity
as an argument just to get the list head.
Make it more generic by changing the function argument
to list_head.
No functional changes.
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The entire logic that represent graph links were developed on a
time where there were no needs to dynamic remove links. So,
although links are created/removed one by one via some
functions, they're stored as an array inside the entity struct.
As the array may grow, there's a logic inside the code that
checks if the amount of space is not enough to store
the needed links. If it isn't the core uses krealloc()
to change the size of the link, with is bad, as it
leaves the memory fragmented.
So, convert links into a list.
Also, currently, both source and sink entities need the link
at the graph traversal logic inside media_entity. So there's
a logic duplicating all links. That makes it to spend
twice the memory needed. This is not a big deal for today's
usage, where the number of links are not big.
Yet, if during the MC workshop discussions, it was said that
IIO graphs could have up to 4,000 entities. So, we may
want to remove the duplication on some future. The problem
is that it would require a separate linked list to store
the backlinks inside the entity, or to use a more complex
algorithm to do graph backlink traversal, with is something
that the current graph traversal inside the core can't cope
with. So, let's postpone a such change if/when it is actually
needed.
It should also be noticed that the media_link structure uses
44 bytes on 32-bit architectures and 84 bytes on 64-bit
architecture. It will thus be allocated out of the 64-bytes and
96-bytes pools respectively. That's a 12.5% memory waste on
64-bit architectures and 31.25% on 32-bit architecture.
A linked list is less efficient than an array in this case, but
this could later be optimized if we can get rid of the reverse
links (with would reduce memory allocation by 50%).
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Links are graph objects that represent the links of two already
existing objects in the graph.
While with the current implementation, it is possible to create
the links earlier, It doesn't make any sense to allow linking
two objects when they are not both created.
So, remove the code that would be handling those early-created
links and add a BUG_ON() to ensure that.
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The smiapp driver creates the pads links before the media entity is
registered with the media device. This doesn't work now that object
IDs are used to create links so the media_device has to be set.
Move entity registration logic before pads links creation.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The uvc driver creates the pads links before the media entity is
registered with the media device. This doesn't work now that obj
IDs are used to create links so the media_device has to be set.
Move entities registration logic before pads links creation.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The vsp1 driver initializes the entities and creates the pads links
before the entities are registered with the media device. This doesn't
work now that object IDs are used to create links so the media_device
has to be set.
Split out the pads links creation from the entity initialization so are
made after the entities registration.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The vsp1 driver creates the pads links before the media entities are
registered with the media device. This doesn't work now that object
IDs are used to create links so the media_device has to be set.
Move entities registration logic before pads links creation.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The omap3isp driver parses the graph endpoints to know how many subdevices
needs to be registered async and register notifiers callbacks for to know
when these are bound and when the async registrations are completed.
Currently the entities pad are linked with the correct ISP input interface
when the subdevs are bound but it happens before entitities are registered
with the media device so that won't work now that the entity links list is
initialized on device registration.
So instead creating the pad links when the subdevice is bound, create them
on the complete callback once all the subdevices have been bound but only
try to create for the ones that have a bus configuration set during bound.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The omap3isp driver initializes the entities and creates the pads links
before the entities are registered with the media device. This does not
work now that object IDs are used to create links so the media_device
has to be set.
Split out the pads links creation from the entity initialization so the links
are created after the entities have been registered with the media device.
Suggested-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Interfaces are different than entities: they represent a
Kernel<->userspace interaction, while entities represent a
piece of hardware/firmware/software that executes a function.
Let's distinguish them by creating a separate structure to
store the interfaces.
Later patches should change the existing drivers and logic
to split the current interface embedded inside the entity
structure (device nodes) into a separate object of the graph.
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The struct media_entity has a .parent field that stores a pointer
to the parent struct media_device. But recently a media_gobj was
embedded into the entities and since struct media_gojb already has
a pointer to a struct media_device in the .mdev field, the .parent
field becomes redundant and can be removed.
This patch replaces all the usage of .parent by .graph_obj.mdev so
that field will become unused and can be removed on a later patch.
No functional changes.
The transformation was made using the following coccinelle spatch:
@@
struct media_entity *me;
@@
- me->parent
+ me->graph_obj.mdev
@@
struct media_entity *link;
@@
- link->source->entity->parent
+ link->source->entity->graph_obj.mdev
@@
struct exynos_video_entity *ve;
@@
- ve->vdev.entity.parent
+ ve->vdev.entity.graph_obj.mdev
Suggested-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
With the new API, a link can be either between two PADs or between an interface
and an entity. So, we need to use a better name for the function that create
links between two pads.
So, rename the such function to media_create_pad_link().
No functional changes.
This patch was created via this shell script:
for i in $(find drivers/media -name '*.[ch]' -type f) $(find drivers/staging/media -name '*.[ch]' -type f) $(find include/ -name '*.h' -type f) ; do sed s,media_entity_create_link,media_create_pad_link,g <$i >a && mv a $i; done
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
It helps to check if the media controller is doing the
right thing with the object creation and removal.
No extra code/data will be produced if DEBUG or
CONFIG_DYNAMIC_DEBUG is not enabled.
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
We can only free the media device after being sure that no
graph object is used.
In order to help tracking it, let's add debug messages
that will print when the media controller gets registered
or unregistered.
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Just like entities and pads, links also need to have unique
Object IDs along a given media controller.
So, let's add a media_gobj inside it and initialize
the object then a new link is created.
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
PADs also need unique object IDs that won't conflict with
the entity object IDs.
The pad objects are currently created via media_entity_init()
and, once created, never change.
While this will likely change in the future in order to
support dynamic changes, for now we'll keep PADs as arrays
and initialize the media_gobj embedded structs when
registering the entity.
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
As entities are graph objects, let's embed media_gobj
on it. That ensures an unique ID for entities that can be
global along the entire media controller.
For now, we'll keep the already existing entity ID. Such
field need to be dropped at some point, but for now, let's
not do this, to avoid needing to review all drivers and
the userspace apps.
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Due to the MC API proposed changes, we'll need to have an unique
object ID for all graph objects, and have some shared fields
that will be common on all media graph objects.
Right now, the only common object is the object ID, but other
fields will be added later on.
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Accessing media_entity ID should now use media_entity_id() macro to
obtain the entity ID, as a next patch will remove the .id field from
struct media_entity .
So, get rid of it, otherwise the omap3isp driver will fail to build.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Instead of accessing directly entity.id, let's create a macro,
as this field will be moved into a common struct later on.
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This logic was broken on the original patch, likely due to a
cut-and-paste mistake.
Fix it.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This was depending on broken because we're working at the
Media Controller API, with has... issues.
As this got fixed, we can re-enable it.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
