We currently manage IRQs in pool_bm which is a bit field
of MAX_MSIX bits. Thus, allocating more than MAX_MSIX
interrupts can't be managed in pool_bm.
Fixing this by capping number of requested MSIXs to
MAX_MSIX.
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Carol L Soto <clsoto@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
arch/s390/net/bpf_jit_comp.c
drivers/net/ethernet/ti/netcp_ethss.c
net/bridge/br_multicast.c
net/ipv4/ip_fragment.c
All four conflicts were cases of simple overlapping
changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
mlx4_core preparation to support hardware accelerated 802.1ad VLAN
device.
To allow 802.1ad accelerated device, "packet has vlan" (phv)
Firmware capability should be available. Firmware without the
phv capability won't behave properly and can't support 802.1ad device
acceleration.
The driver checks the Firmware capability and sets the phv bit
accordingly in SET_PORT command.
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some old PF drivers don't let VFs allocate counters, in that case, use
the sink counter so the VF can load and operate properly.
Fixes: 6de5f7f6a1 ('net/mlx4_core: Allocate default counter per port')
Reported-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add extra check for total vfs for SRIOV to check if that value is
bigger than total vfs in pci SRIOV capabalities. Fix a check and
print of the number of maximum vfs that hw can handle. Fix a check
and print of the number of maximum vfs per port that driver can handle.
Signed-off-by: Carol L Soto <clsoto@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking updates from David Miller:
1) Add TX fast path in mac80211, from Johannes Berg.
2) Add TSO/GRO support to ibmveth, from Thomas Falcon
3) Move away from cached routes in ipv6, just like ipv4, from Martin
KaFai Lau.
4) Lots of new rhashtable tests, from Thomas Graf.
5) Run ingress qdisc lockless, from Alexei Starovoitov.
6) Allow servers to fetch TCP packet headers for SYN packets of new
connections, for fingerprinting. From Eric Dumazet.
7) Add mode parameter to pktgen, for testing receive. From Alexei
Starovoitov.
8) Cache access optimizations via simplifications of build_skb(), from
Alexander Duyck.
9) Move page frag allocator under mm/, also from Alexander.
10) Add xmit_more support to hv_netvsc, from KY Srinivasan.
11) Add a counter guard in case we try to perform endless reclassify
loops in the packet scheduler.
12) Extern flow dissector to be programmable and use it in new "Flower"
classifier. From Jiri Pirko.
13) AF_PACKET fanout rollover fixes, performance improvements, and new
statistics. From Willem de Bruijn.
14) Add netdev driver for GENEVE tunnels, from John W Linville.
15) Add ingress netfilter hooks and filtering, from Pablo Neira Ayuso.
16) Fix handling of epoll edge triggers in TCP, from Eric Dumazet.
17) Add an ECN retry fallback for the initial TCP handshake, from Daniel
Borkmann.
18) Add tail call support to BPF, from Alexei Starovoitov.
19) Add several pktgen helper scripts, from Jesper Dangaard Brouer.
20) Add zerocopy support to AF_UNIX, from Hannes Frederic Sowa.
21) Favor even port numbers for allocation to connect() requests, and
odd port numbers for bind(0), in an effort to help avoid
ip_local_port_range exhaustion. From Eric Dumazet.
22) Add Cavium ThunderX driver, from Sunil Goutham.
23) Allow bpf programs to access skb_iif and dev->ifindex SKB metadata,
from Alexei Starovoitov.
24) Add support for T6 chips in cxgb4vf driver, from Hariprasad Shenai.
25) Double TCP Small Queues default to 256K to accomodate situations
like the XEN driver and wireless aggregation. From Wei Liu.
26) Add more entropy inputs to flow dissector, from Tom Herbert.
27) Add CDG congestion control algorithm to TCP, from Kenneth Klette
Jonassen.
28) Convert ipset over to RCU locking, from Jozsef Kadlecsik.
29) Track and act upon link status of ipv4 route nexthops, from Andy
Gospodarek.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1670 commits)
bridge: vlan: flush the dynamically learned entries on port vlan delete
bridge: multicast: add a comment to br_port_state_selection about blocking state
net: inet_diag: export IPV6_V6ONLY sockopt
stmmac: troubleshoot unexpected bits in des0 & des1
net: ipv4 sysctl option to ignore routes when nexthop link is down
net: track link-status of ipv4 nexthops
net: switchdev: ignore unsupported bridge flags
net: Cavium: Fix MAC address setting in shutdown state
drivers: net: xgene: fix for ACPI support without ACPI
ip: report the original address of ICMP messages
net/mlx5e: Prefetch skb data on RX
net/mlx5e: Pop cq outside mlx5e_get_cqe
net/mlx5e: Remove mlx5e_cq.sqrq back-pointer
net/mlx5e: Remove extra spaces
net/mlx5e: Avoid TX CQE generation if more xmit packets expected
net/mlx5e: Avoid redundant dev_kfree_skb() upon NOP completion
net/mlx5e: Remove re-assignment of wq type in mlx5e_enable_rq()
net/mlx5e: Use skb_shinfo(skb)->gso_segs rather than counting them
net/mlx5e: Static mapping of netdev priv resources to/from netdev TX queues
net/mlx4_en: Use HW counters for rx/tx bytes/packets in PF device
...
Conflicts:
drivers/net/ethernet/mellanox/mlx4/main.c
net/packet/af_packet.c
Both conflicts were cases of simple overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
Default counter per port will be allocated at the mlx4 core driver load.
Every QP opened by the Ethernet driver will be attached to the port's default
counter. This is an infrastructure step to collect VF statistics from the PF.
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since virtual functions get their counters indices allocation from the PF,
allocate counters indices bitmap only in case the function isn't virtual.
Also, check that the device has counters to allocate before creating the
indices bitmap table.
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reserve the last valid counter index for "sink" counter, when a
new counter cannot be allocated, the driver will use this counter.
In order to avoid allocating this counter on any other flow, fix the
indices bitmap allocation range, and reserve the sink counter index.
Add macro for the sink counter index and replace all appearences of the
index with the macro.
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add resetting the counter data to the free counter flow, so the counter's
data won't be accessible anymore if querying the counter. Also, on next
counter allocation (to another VM for example), it will be fresh and clear.
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If counters are not supported by the device. The indices bitmap table is not
allocated during initialization. Add the symmetrical check before cleaning
the counters bitmap table or freeing a counter.
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Due to firmware bug, under VPI configuration when port1 = IB and
port2 = Eth, Granular QoS per VF isn't working properly. More over,
the whole QP0/QP1 Para-Virtualization in the mlx4 IB driver is
broken on that config.
Hence, we must disable Granular QoS per VF under that configuration
till a fix is introduced. Once that happens, a new device capability
will be used to mark the feature support on that specific configuration.
Reported-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to read the HCA's cycle counter efficiently in
user space, we need to map the HCA's register.
This is done through mmap call.
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
If mlx4_enable_sriov is called by adapter without this
feature MLX4_DEV_CAP_FLAG2_SYS_EQS then during this path the function alloc
icm is called twice without freeing the structures from the first time.
Acked-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Carol L Soto <clsoto@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If user loads mlx4_core with num_vfs greater than
supported then variable dev->dev_vfs is freed 2 times after unloading the
driver.
Acked-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Carol L Soto <clsoto@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that EQs management is in the sole responsibility of mlx4_core,
the IRQ affinity hints configuration should be in its hands as well.
request_irq is called only once by the first consumer (maybe mlx4_ib),
so mlx4_en passes the affinity mask too late. We also need to request
vectors according to the cores we want to run on.
mlx4_core distribution of IRQs to cores is straight forward,
EQ(i)->IRQ will set affinity hint to core i.
Consumers need to request EQ vectors, according to their cores
considerations (NUMA).
Signed-off-by: Ido Shamay <idos@mellanox.com>
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Previously, mlx4_en allocated EQs and used them exclusively.
This affected RoCE performance, as applications which are
events sensitive were limited to use only the legacy EQs.
Change that by introducing an EQ pool. This pool is managed
by mlx4_core. EQs are assigned to ports (when there are limited
number of EQs, multiple ports could be assigned to the same EQs).
An exception to this rule is the ASYNC EQ which handles various events.
Legacy EQs are completely removed as all EQs could be shared.
When a consumer (mlx4_ib/mlx4_en) requests an EQ, it asks for
EQ serving on a specific port. The core driver calculates which
EQ should be assigned to that request.
Because IRQs are shared between IB and Ethernet modules, their
names only include the PCI device BDF address.
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Ido Shamay <idos@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove the limitation that disallows configuring single ported VFs
in the presence of IB ports, after addressing the issues that
prevented that to work.
SMI (QP0) requests/responses are still not supported for single
ported IB VFs.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
To have out of the box experience, the PF generates random GUIDs who
serve as the initial admin values.
Signed-off-by: Yishai Hadas <yishaih@mellanox.com>
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Manages alias GUIDs per VF per port in the core layer.
This is a pre-step for managing alias GUIDs in a mode that the admin
GUID is returned via ib_query_gid() regardless of whether the SM
has approved it or not.
Signed-off-by: Yishai Hadas <yishaih@mellanox.com>
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Enabled when the device supports KEEP FCS and IGNORE FCS.
When the flag is set, pass all received frames up the stack,
even ones with invalid FCS, controlled by ethtool.
Signed-off-by: Muhammad Mahajna <muhammadm@mellanox.com>
Signed-off-by: Ido Shamay <idos@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A new capability bit was introduced in the past to to differ devices
using the QoS ETS feature. The old was deprecated since then.
If driver sees device which set only the old capabilty, it will print
warning to user suggesting to upgrade the FW.
Signed-off-by: Ido Shamay <idos@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Enable RSS support for fragmented IP packets, when device supports it.
Until now, fragmented IP packets were directed only to the default_qpn.
Since IP fragments (datagram) have no upper protocols (L3 IP packets),
hash is performed on 3-tuple - dst MAC, source IP and dest IP. The HW
makes sure that this holds for the 1st fragment too, so all fragments
go to the same QP.
Signed-off-by: Ido Shamay <idos@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the low-level device commands and definitions used for QP max-rate limiting.
This is done through the following elements:
- read rate-limit device caps in QUERY_DEV_CAP: number of different
rates and the min/max rates in Kbs/Mbs/Gbs units
- enhance the QP context struct to contain rate limit units and value
- allow to do run time rate-limit setting to QPs through the
update-qp firmware command
- QP rate-limiting is disallowed for VFs
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We do support cache line sizes of 32 and 64 bytes without activating the
CQE stride feature. Fix a misleading print saying that these cache line
sizes aren't supported.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Supply interface functions to bond and unbond ports of a mlx4 internal
interfaces. Example for such an interface is the one registered by the
mlx4 IB driver under RoCE.
There are
1. Functions to go in/out to/from bonded mode
2. Function to remap virtual ports to physical ports
The bond_mutex prevents simultaneous access to data that keep status of
the device in bonded mode.
The upper mlx4 interface marks to the mlx4 core module that they
want to be subject for such bonding by setting the MLX4_INTFF_BONDING
flag. Interface which goes to/from bonded mode is re-created.
The mlx4 Ethernet driver does not set this flag when registering the
interface, the IB driver does.
Signed-off-by: Moni Shoua <monis@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Structs allocated for the resource tracker must be freed in
the error flow.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The reserved lKey is different for each VF.
A base lkey value is returned in QUERY_DEV_CAP at offset 0x98.
The reserved L_key value for a VF is:
VF_lkey = base_lkey + (VF_number << 8).
This VF L_key value should be returned in QUERY_FUNC_CAP
(opcode-modifier = 0) at offset 0x48.
To indicate that the lkey value at offset 0x48 is valid, the Hypervisor
sets a flag bit in dword 0x0, offset 27 in the QUERY_FUNC_CAP wrapper
function.
When the VF calls QUERY_FUNC_CAP, it should check if this flag bit is set.
If it is set, the VF should take the reserved lkey value at offset 0x48.
If the bit is not set, the VF should not use a reserved lkey
(i.e., should set its reserved lkey value to 0).
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
arch/arm/boot/dts/imx6sx-sdb.dts
net/sched/cls_bpf.c
Two simple sets of overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
When SRIOV commands are executed over the comm-channel and get
a fatal error (e.g. timeout, closing command failure) the VF enters
into error state and reset flow is activated.
To be able to recognize whether the failure was on a closing command, the
operational code for the given VHCR command is used. Once the device entered
into an error state we prevent redundant error messages from being printed.
Signed-off-by: Yishai Hadas <yishaih@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In SRIOV, both the PF and the VF may attempt device recovery whenever they
assume that the device is not functioning. When the PF driver resets the
device, the VF should detect this and attempt to reinitialize itself.
The VF must be able to reset itself under all circumstances, even
if the PF is not responsive.
The VF shall reset itself in the following cases:
1. Commands are not processed within reasonable time over the communication channel.
This is done considering device state and the correct return code based on
the command as was done in the native mode, done in the next patch.
2. The VF driver receives an internal error event reported by the PF on the
communication channel. This occurs when the PF driver resets the device or
when VF is out of sync with the PF.
Add 'VF reset' capability, which allows the VF to reinitialize itself even when the
PF is not responsive.
As PF and VF may run their reset flow simulantanisly, there are several cases
that are handled:
- Prevent freeing VF resources upon FLR, when PF is in its unloading stage.
- Prevent PF getting VF commands before it has finished initializing its resources.
- Upon VF startup, check that comm-channel is online before sending
commands to the PF and getting timed-out.
Signed-off-by: Yishai Hadas <yishaih@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix AER callbacks to work properly, it includes:
- Refractoring AER to be aligned with Reset flow support.
- Sync with concurrent catas flow.
In addition, fix the shutdown PCI callback to sync with
concurrent catas flow.
Signed-off-by: Yishai Hadas <yishaih@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We need to manage interface state to sync between reset flow and some other
relative cases such as remove_one. This has to be done to prevent certain
races. For example in case software stack is down as a result of unload call,
the remove_one should skip the unload phase.
Implement the remove_one case, handling AER and other cases comes next.
The interface can be up/down, upon remove_one, the state will include an extra
bit indicating that the device is cleaned-up, forcing other tasks to finish
before the final cleanup.
Signed-off-by: Yishai Hadas <yishaih@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This includes:
- resetting the chip when a fatal error is detected (the current code
does not do this).
- exposing the ability to enter error state from outside the catas code
by calling its functionality. (E.g. FW Command timeout, AER error).
- managing a persistent device state. This is needed to sync between
reset flow cases.
Signed-off-by: Yishai Hadas <yishaih@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Using a WQ per device instead of a single global WQ, this allows
independent reset handling per device even when SRIOV is used.
This comes as a pre-patch for supporting chip reset
for both native and SRIOV.
Signed-off-by: Yishai Hadas <yishaih@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When an HCA enters an internal error state, this is detected by the driver.
The driver then should reset the HCA and restart the software stack.
Keep ports information and some SRIOV configuration in a persistent area
to have it valid across reset.
Signed-off-by: Yishai Hadas <yishaih@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Maintain a persistent memory that should survive reset flow/PCI error.
This comes as a preparation for coming series to support above flows.
Signed-off-by: Yishai Hadas <yishaih@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Except for VXLAN steering rules, all offloads should work as they were
under plain DMFS mode. Fix that by enabling all the offloads under
DMFS-A0 mode, except for VXLAN steering rules.
Fixes: d57febe1a4 "net/mlx4: Add A0 hybrid steering"
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We shouldn't call UNMAP_FA here, this is done in mlx4_load_one.
If mlx4_query_func fails, we need to invoke CLOSE_HCA for both
native and master.
Fixes: a0eacca948 ('net/mlx4_core: Refactor mlx4_load_one')
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- On-demand paging support in core midlayer and mlx5 driver. This lets
userspace create non-pinned memory regions and have the adapter HW
trigger page faults.
- iSER and IPoIB updates and fixes.
- Low-level HW driver updates for cxgb4, mlx4 and ocrdma.
- Other miscellaneous fixes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=MCO9
-----END PGP SIGNATURE-----
Merge tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband
Pull infiniband updates from Roland Dreier:
"Main batch of InfiniBand/RDMA changes for 3.19:
- On-demand paging support in core midlayer and mlx5 driver. This
lets userspace create non-pinned memory regions and have the
adapter HW trigger page faults.
- iSER and IPoIB updates and fixes.
- Low-level HW driver updates for cxgb4, mlx4 and ocrdma.
- Other miscellaneous fixes"
* tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband: (56 commits)
IB/mlx5: Implement on demand paging by adding support for MMU notifiers
IB/mlx5: Add support for RDMA read/write responder page faults
IB/mlx5: Handle page faults
IB/mlx5: Page faults handling infrastructure
IB/mlx5: Add mlx5_ib_update_mtt to update page tables after creation
IB/mlx5: Changes in memory region creation to support on-demand paging
IB/mlx5: Implement the ODP capability query verb
mlx5_core: Add support for page faults events and low level handling
mlx5_core: Re-add MLX5_DEV_CAP_FLAG_ON_DMND_PG flag
IB/srp: Allow newline separator for connection string
IB/core: Implement support for MMU notifiers regarding on demand paging regions
IB/core: Add support for on demand paging regions
IB/core: Add flags for on demand paging support
IB/core: Add support for extended query device caps
IB/mlx5: Add function to read WQE from user-space
IB/core: Add umem function to read data from user-space
IB/core: Replace ib_umem's offset field with a full address
IB/mlx5: Enhance UMR support to allow partial page table update
IB/mlx5: Remove per-MR pas and dma pointers
RDMA/ocrdma: Always resolve destination mac from GRH for UD QPs
...
Move check for DPDP out of the loop to make the code more readable.
Signed-off-by: Yuval Shaia <yuval.shaia@oracle.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
To support asymmetric EQ allocations, we should query the device
capabilities prior to enabling SRIOV. As a side effect of adding that,
we are dumping the PF device capabilities twice. Avoid that by moving
the printing into a helper function which is called once.
Fixes: 7ae0e400cd ('net/mlx4_core: Flexible (asymmetric) allocation of
EQs and MSI-X vectors for PF/VFs')
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current mlx4_load_one has a memory leak as it always allocates
dev_cap, but frees it only on error.
In addition, even if VFs exist when mlx4_load_one is called,
we still need to notify probed VFs that we're loading (by
incrementing pf_loading).
Fixes: a0eacca948 ('net/mlx4_core: Refactor mlx4_load_one')
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the required firmware commands for A0 steering and a way to enable
that. The firmware support focuses on INIT_HCA, QUERY_HCA, QUERY_PORT,
QUERY_DEV_CAP and QUERY_FUNC_CAP commands. Those commands are used
to configure and query the device.
The different A0 DMFS (steering) modes are:
Static - optimized performance, but flow steering rules are
limited. This mode should be choosed explicitly by the user
in order to be used.
Dynamic - this mode should be explicitly choosed by the user.
In this mode, the FW works in optimized steering mode as long as
it can and afterwards automatically drops to classic (full) DMFS.
Disable - this mode should be explicitly choosed by the user.
The user instructs the system not to use optimized steering, even if
the FW supports Dynamic A0 DMFS (and thus will be able to use optimized
steering in Default A0 DMFS mode).
Default - this mode is implicitly choosed. In this mode, if the FW
supports Dynamic A0 DMFS, it'll work in this mode. Otherwise, it'll
work at Disable A0 DMFS mode.
Under SRIOV configuration, when the A0 steering mode is enabled,
older guest VF drivers who aren't using the RX QP allocation flag
(MLX4_RESERVE_A0_QP) will get a QP from the general range and
fail when attempting to register a steering rule. To avoid that,
the PF context behaviour is changed once on A0 static mode, to
require support for the allocation flag in VF drivers too.
In order to enable A0 steering, we use log_num_mgm_entry_size param.
If the value of the parameter is not positive, we treat the absolute
value of log_num_mgm_entry_size as a bit field. Setting bit 2 of this
bit field enables static A0 steering.
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently QUERY_PORT is done as a part of QUERY_DEV_CAP firmware command.
Since we would like to use it without querying all device capabilities,
extract this part to be a function of its own.
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A0 hybrid steering is a form of high performance flow steering.
By using this mode, mlx4 cards use a fast limited table based steering,
in order to enable fast steering of unicast packets to a QP.
In order to implement A0 hybrid steering we allocate resources
from different zones:
(1) General range
(2) Special MAC-assigned QPs [RSS, Raw-Ethernet] each has its own region.
When we create a rss QP or a raw ethernet (A0 steerable and BF ready) QP,
we try hard to allocate the QP from range (2). Otherwise, we try hard not
to allocate from this range. However, when the system is pushed to its
limits and one needs every resource, the allocator uses every region it can.
Meaning, when we run out of raw-eth qps, the allocator allocates from the
general range (and the special-A0 area is no longer active). If we run out
of RSS qps, the mechanism tries to allocate from the raw-eth QP zone. If that
is also exhausted, the allocator will allocate from the general range
(and the A0 region is no longer active).
Note that if a raw-eth qp is allocated from the general range, it attempts
to allocate the range such that bits 6 and 7 (blueflame bits) in the
QP number are not set.
When the feature is used in SRIOV, the VF has to notify the PF what
kind of QP attributes it needs. In order to do that, along with the
"Eth QP blueflame" bit, we reserve a new "A0 steerable QP". According
to the combination of these bits, the PF tries to allocate a suitable QP.
In order to maintain backward compatibility (with older PFs), the PF
notifies which QP attributes it supports via QUERY_FUNC_CAP command.
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When using BF (Blue-Flame), the QPN overrides the VLAN, CV, and SV fields
in the WQE. Thus, BF may only be used for QPNs with bits 6,7 unset.
The current Ethernet driver code reserves a Tx QP range with 256b alignment.
This is wrong because if there are more than 64 Tx QPs in use,
QPNs >= base + 65 will have bits 6/7 set.
This problem is not specific for the Ethernet driver, any entity that
tries to reserve more than 64 BF-enabled QPs should fail. Also, using
ranges is not necessary here and is wasteful.
The new mechanism introduced here will support reservation for
"Eth QPs eligible for BF" for all drivers: bare-metal, multi-PF, and VFs
(when hypervisors support WC in VMs). The flow we use is:
1. In mlx4_en, allocate Tx QPs one by one instead of a range allocation,
and request "BF enabled QPs" if BF is supported for the function
2. In the ALLOC_RES FW command, change param1 to:
a. param1[23:0] - number of QPs
b. param1[31-24] - flags controlling QPs reservation
Bit 31 refers to Eth blueflame supported QPs. Those QPs must have
bits 6 and 7 unset in order to be used in Ethernet.
Bits 24-30 of the flags are currently reserved.
When a function tries to allocate a QP, it states the required attributes
for this QP. Those attributes are considered "best-effort". If an attribute,
such as Ethernet BF enabled QP, is a must-have attribute, the function has
to check that attribute is supported before trying to do the allocation.
In a lower layer of the code, mlx4_qp_reserve_range masks out the bits
which are unsupported. If SRIOV is used, the PF validates those attributes
and masks out unsupported attributes as well. In order to notify VFs which
attributes are supported, the VF uses QUERY_FUNC_CAP command. This command's
mailbox is filled by the PF, which notifies which QP allocation attributes
it supports.
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.co.il>
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We now allow up to 126 VFs. Note though that certain firmware
versions only allow up to 80 VFs. Moreover, old HCAs only support 64 VFs.
In these cases, we limit the maximum number of VFs to 64.
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Previously, the driver queried the firmware in order to get the number
of supported EQs. Under SRIOV, since this was done before the driver
notified the firmware how many VFs it actually needs, the firmware had
to take into account a worst case scenario and always allocated four EQs
per VF, where one was used for events while the others were used for completions.
Now, when the firmware supports the asymmetric allocation scheme, denoted
by exposing num_sys_eqs > 0 (--> MLX4_DEV_CAP_FLAG2_SYS_EQS), we use the
QUERY_FUNC command to query the firmware before enabling SRIOV. Thus we
can get more EQs and MSI-X vectors per function.
Moreover, when running in the new firmware/driver mode, the limitation
that the number of EQs should be a power of two is lifted.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
